Search Documents

By L. Tafaghodi, A. Hosseinpour

"Silicon is considered as the most appropriate semiconductor material for manufacturing solar cells because of its natural abundance and being nontoxic. The transferable knowledge and technology from the electronics industry and the long history of silicon-based semiconductors are also assisting the domination of silicon as the most common semiconductor material. Developing an environmentally and economically viable process for producing solar grade silicon has been one of the main challenges in the silicon industry in the past few years. Metallurgical refining processes have received significant attention because of their high productivity and low cost. Slag refining is one of the purification methods which is based on oxidation of the impurity elements, followed by its dissolution into a slag phase. This article presents a review of various slag refining processes that have been employed for purification of silicon and silicon alloys. SiO2, CaO, CaF2, CaCl2, Al2O3, MgO and Na2O are the major components of the slags used for silicon refining. These slags can be classified into three main categories including binary, ternary and quaternary slags.INTRODUCTION Silicon can be categorized into three different grades based on its application or purity: metallurgical grade silicon (MG-Si) with purity of ~98 %, solar grade silicon (SoG-Si) with purity of ~99.99999 % and semiconductor grade silicon (SeG-Si) which has the purity of 99.9999999 % (Johnston & Barati, 2010; Krystad, Tang, & Tranell, 2012; Tang, Øvrelid, Tranell, & Tangstad, 2009). Producing SeG-Si is carried out through an energy-intensive and complicated process named Siemens. This purification process is relatively slow and involves using toxic and corrosive reagents (e.g. Trichlorosilane). At present the majority of SoG-Si is produced via Siemens or Siemens-like processes and there is very limited production via processes dedicated to SoG-Si. Because of the difference in silicon specifications required in microelectronics and photovoltaic industry, and the cost and energy associated with the Siemens process, an interest has emerged to develop technologies dedicated to producing low cost SoG-Si (Istratov et al., 2003; Johnston, Khajavi, Li, Sokhanvaran, & Barati, 2012; Mitrašinovic, D'Souza, & Utigard, 2012; Wu et al., 2012)."

Jan 1, 2017

By Lex L. Udy

External-detonation-generated plasmas, highly ionized zones of reacting material ejected from the surface of detonating explosive charges, are shown to be the cause of channel desensitization, i.e., the self-quenching of a detonating explosive column loaded in a borehole with an air annulus between the explosive and the borehole wall. The effects of this phenomenon on several explosive compositions and types are demonstrated and discussed. The explosives tested include aluminum-sensitized and explosive-sensitized slurries, ANFO, liquid explosives and dynamites. Various techniques are described that can be used to reduce or eliminate the plasma effect.

Jan 1, 1979

By L. Rao, P. Carabin

"Advances in thermal plasma torches have resulted in this technology becoming a commercially viable solution for chemical and metallurgical processes. The main advantages of plasma are its ability to control process chemistry and to build small footprint reactors due to its high energy density and reactivity of the free radicals that are produced. This paper focuses on thermal plasmas produced by DC torches and their applications for waste treatment, production of high purity metals, and nanomaterials. Both transferred and non-transferred torches have been used as either a source of heat or as a reagent in various industrial processes. INTRODUCTIONPlasma technology has become an ideal solution for many industrial chemical, metallurgical and mechanical processes (Venkataramani, 2002). Thermal plasma powered systems are typical used for their unique characteristics such as high energy densities, high temperatures, small installation sizes, rapid startup and shutdown features, controlled process chemistry and use of electrical energy as a heating source resulting in decoupling the heat source from the oxygen flow rate (Heberlein et al., 2007). Depending on the nature of the main plasma forming gas used, thermal plasma systems offer a high temperature heating source coupled with a highly reactive plasma plume rich in free radicals and ions which promote otherwise hard to drive chemical reactions, as well as high heat transfer rates.Industrial plasmas can be broadly classified as thermal plasmas and non thermal plasmas. Thermal plasmas are atmospheric pressure plasmas characterized by local thermodynamic equilibrium (Boulos et al., 1994). Thermal plasmas are typically established between any two current conducting electrodes separated by an insulator. A plasma forming gas is blown between the two conducting electrodes resulting in a high temperature plasma plume. A plasma torch generates and maintains an electrically conducting gas column between the two electrodes; a cathode (negative electrode) and an anode (positive electrode) (Camacho, 1988). If both electrodes are housed in a single housing, resulting in an arc enclosed inside the plasma torch, then such plasma generating torches are termed as non-transferred (NT) plasma torches, whereas, if the second electrode is external to the torch, creating an arc transferred between the cathode and the working piece, then such plasma torches are termed as transferred (T) plasma torches. Depending on the source of the electricity which can be either direct current (DC), alternating current (AC) at main network frequency or at radio frequency (RF), the plasma torches are classified as DC, AC or RF plasma torches (Venkataramani, 2002)."

Jan 1, 2012

By M. Medraj, M. A. Arafin, D. P. Turner, P. Bocher

In this study, the kinetics of isothermal solidification during TLP bonding of Inconel 625 and 718 superalloys with nickel based multi-component filler alloy BNi-2 have been studied through a combination of direct experimentation and mathematical modeling in order to determine the effect of process variables and, thus, to optimize the process. The predicted isothermal solidification completion times from the boron diffusion model and migrating solid/liquid interface model were in good agreement with the experimentally determined values and, they were found to be significantly less than those of other nickel superalloys with different nickel based filler alloys. Further, significant reduction of holding time was observed with increasing bonding temperature and with decreasing joint gap. No significant grain growth in the base metals has been observed in the temperature range being investigated (1325 - 1394K).

Jan 1, 2006

By R. G. S. Mussi

An inclined cooling plate is utilized as a modification in the compocasting process of magnesium alloy and the mechanical properties of the composites obtained are studied in this work. Based on crystal separation theory, molten AZ91D is poured onto an inclined plate in order to produce solidification nuclei inside the fluid metal, and is mechanically stirred while reinforcement is added. Particulate SiC was utilized as reinforcement in quantities varying from 0 to 15%vol. Dispersion of the reinforcement was observed by macro and microstructure analysis. SiC was properly mixed into matrix until 15%vol., and Vickers hardness tests were carried out for the composites produced. Results obtained for hardness were shown to increase with reinforcement addition and comparable to those of traditional compocasting. Utilization of Inclined Cooling Plate produced good inclusion and homogenization of SiC through an AZ91D matrix, at lower temperatures and shorter times than traditional compocasting.

Jan 1, 2006

By S. L. Gula

"Effective and timely communication during routine operations, and especially during emergency situations, is no easy task in any underground mine. At Cominco Fertilizers, Potash Operations, where 150people are employed underground to produce 3.1 million tonnes of potash per annum at a depth of 1100 m (3600ft), this is no exception. The over-all mine workings underlie an area of approximately 20 km 2 with average travel time to the active mining areas being approximately 30 to 40 minutes by light vehicle, and significantly longer than this for heavy equipment.In a mine of this size, the deployment and management of personnel and materials on a day-to-day basis, and during mine emergencies, is an important exercise. The Personal Emergency Device (PED) system has provided the Potash Division a means to achieve improvements in this area and reduce the communications bottleneck.The MineAt Cominco Fertilizers Potash Operations, approximately 30 km southwest of Saskatoon, the orebody is the same horizon being mined by other potash producers in the Saskatoon area and extends over 300 km in an east-west direction, and approximately 150 km in a north-south direction. Mining operations are carried out with approximately 150 employees operating on a continuous-shift basis, seven days a week.Mining is presently being done from Block 6 which takes the mine to its northernmost boundary and contains reserves of approximately 50 million tonnes. Production is from one level by five twin rotor continuous mining machines, each capable of cutting a face up to 5.5 m wide and 3.3 m high . All ore is transported to the shaft via approximately 20 km of conveyor where it is removed to surface by two 24 tonne skips.After the ore is conveyed to the mill for processing, the finished product is shipped by rail car or trucks to other parts of Canada, the United States or through Vancouver to other parts of the world."

Jan 1, 1993

By Hagen B. Schultes

"Refratechnik, a leading German refractory company, acquired a majority shareholding in Baymag in 1979. This acquisition included the mining rights for a magnesite deposit of exceptionally high purity in the Canadian Rocky Mountains.The deposit, situated in the Kootenay region of southeastern British Columbia, is of Cambrian age and has ore reserves of 50 million m. t. of magnesite. The Baymag magnesite deposit is one of the purest in the world. The deposit was opened up and mining commenced in early 1982. Production of various caustic calcined magnesia products in a rotary kiln operation in Exshaw, Alberta, was started in mid-1982. The product application ranges from pulp and paper production, to the chemical industry, and to animal feed supplements. Since the end of 1983, Baymag has produced high-quality refractory grade fused magnesium oxide f or specialty applications in the steel industry.IntroductionAlthough magnesium is the eighth most abundant element in the earth and forms about 2.06% of the earth's crust, common knowledge about magnesium and especially magnesium oxide (MgO) as an industrial mineral is not widespread. The reason might be that, with the exception of magnesium metal as the element, magnesia products are not generally sold as final products to end-users, but rather are needed for the production of final products such as steel, cement, paper, etc. Therefore, some general comments are given about the different sources of MgO, the different products, world production and consumption , before Baymag specifics are addressed. Magnesium metal will not be discussed in this paper."

Jan 1, 1986

By R. V. Tomkins

Introduction In the past fifteen years, bentonite production in the United States has increased very rapidly. From l50,000 tons in l934, it rose to 400,000 tons in l 942 and to a record 920,000 tons in 1948. Occurrences of bentonite ?in western Canada were described in the early part of the century by Ries and Keele (3), Ells (2), Spence (4). and other officer of the Dominion Department of Mines, and, in Saskatchewan, Professor W. G. Worcester (6), of the University of Saskatchewan has explored and carried out tests on deposits of the material at various times during the past thirty years. Nevertheless, Canadian developments have not kept pace with those in the United States. Exact figures for total Canadian production are not released, but it is probably under l0,000 tons annually. There are a great number of uses for bentonite, but in the United States three alone account for 90 per cent of the consumption. These are for drilling gel, foundry sand bond, and oil decolorizer. The tremendous oil exploration programme on the Canadian prairies has increased the possibility of an adequate domestic market for drilling gel. Therefore, in Saskatchewan, our efforts have been directed mainly to the production of a good drilling gel, with a minor part of the project devoted to activation of bentonites for oil decolorizing.

Jan 1, 1952

By R. H. McCorkell

Measurements of radon in air and aqueous solutions can be affected by leakage from vessels in which samples and standards are kept and by absorption and later release of radon by the materials of these vessels. The author had received various oral communications concerning the se processes : e.g ., that natural rubber and greases absorb large amounts of radon, whereas silicone rubber and grease do not; and that radon is readily lost from polyethylene bottles and that inverting glass bottles containing aqueous samples reduced radon loss from them . However, the results of actual tests and quantitative data showing these effects were not available. For this reason, it was necessary to make numerous measurements of the leakage and absorption of radon in the course of designing apparatus and methods for measuring radium and radon concentrations. It was thought that the data obtained might be of use to others, and consequently they are compiled in the present note .

Jan 1, 1980

By M. Reda

Because of the adverse environmental effect of Chromate, Molybdate ions had been investigated as replacement for Chromate and the results had shown not to be encouraging. Film deposited from peroxopolymolybdate (from reaction of Molybdenum meta, with excess Hydrogen Peroxide), are more robust than that deposited from molybdate solutions. This was shown to be due to higher fraction of Mo (IV) and Mo (V) that form from Mo (VI) in the peroxopolymolybdate deposited film than the film deposited from Molybdate solutions. The peroxopolymolybdate film contains 40% un-hydrated molybdic acid, tetraperoxodimolybdate and tetra peroxo tetra molybdate. The protective properties of peroxopolymolybdate were shown to be due to the effectiveness of the un-hydrated molybdic acid.

Jan 1, 2010

By Noel Brien, O&apos

General: National Asbestos Mines Limited has operated an asbestos mine and mill near Thetford Mines, Quebec, since 1958. As a result of additional exploration of the orebody in 1962-63, it became apparent that long-range mining plans would have to be revised to allow for a large increase in both ore and waste tonnages. It was decided that the task of checking out possible mine designs could best be analyzed by a computer to obtain data from which an optimum open-pit configuration could be plotted. Object: It was desired to arrive at an optimum open-pit configuration with an over-all pit slope of 45 degrees and a minimum operational width of 200 ft. at the bottom. Calculations were based on assay values from diamond drill holes in cross sections of the mine. The computer's assignment was to select and describe, by coordinates, the optimum cross section for the mine. Mine engineers then assembled the various optimum sections to produce the pit outline. As this would not necessarily result in a practical mining arrangement, the computer also provided alternate solutions,

Jan 1, 1965

By A. Mukherjee, C. Kelly, B. Markovich, G. E. Agar, G. E. Robertson, F. Khan, B. Shea

"Laboratory batch flotation tests were performed on a sample of bulk slow cooled converter matte (Cu:Ni = I) to optimize the time in each of the separation stages. Numerical simulations were carried out to estimate a continuous circuit material balance for the conditions selected. An experimental simulation of a continuous circuit (locked cycle test) readily came to steady state and there was reasonable agreement between the numerical and experimental results. The use of nitrogen as the flotation gas and the addition of collector to the grinding mill minimized the oxidation of chalcocite, which has previously resulted in increasing circulating loads, and led to a stable circuit with very low weights in the recycle streams.IntroductionINCO Limited developed a flotation process for separating the components of copper-nickel matte [Sproule, Harcourt and Rose 1945; Sproule, Harcourt and Renzoni 1960] in 1945 to replace the Orford process and continues to use the flotation process in almost the original mode to this day. Initially the matte processed was the result of smelting a nickel concentrate that analyzed about 12% nickel and 2% copper and all of the recycle material that was generated in the smelting process. The matte generated analyzed about 25% copper and 53% nickel, roughly 2: 1 nickel to copper. This matte was blown in Pierce-Smith converters to be sulfur deficient in order to produce a metallic phase that collected the precious metals contained in the smelter feed [Wilson and Stratton-Crawley 1991]. This process continued with little change until 1994 when the separation of chalcopyrite from pentlandite in the Copper Cliff mill was discontinued after 63 years of operation. As a consequence of the elimination of the primary separation of chalcopyrite from pentlandite in the milling process a bulk concentrate was produced for smelting. Bulk concentrate smelting came into practice in 1994 as part of the initiative to meet government legislation that restricted the emission of sulfur dioxide to the atmosphere. Previously, the copper concentrate was smelted in an INCO oxygen flash furnace which resulted in the capture of a high strength sulfur dioxide stream from which liquid sulfur dioxide was produced. Nickel concentrate was smelted in reverberatory furnaces that produced low strength sulfur dioxide gases which were difficult to treat. The action taken by INCO to meet the environmental constraints was to smelt a bulk concentrate in oxygen flash furnaces which would produce gases suitable for the production of liquid sulfur dioxide and another stream that was high enough in sulfur dioxide to be readily converted to sulfuric acid [Bell et al 1990]. The end result of this decision was that all the copper-nickel separation would be done in the matte separation plant."

Jan 1, 1996

By R. B. Stein

"Countercurrent decantation circuits(CCD) are often employed in hydrometallurgy to effect solids-liquid separation in combination with a barren solution wash to reduce losses of valuable solution component(s) from the tails. Bechtel Corporation uses its BEMSIM flowsheet-modelling PC computer program to simulate a CCD circuit where the ""dirty"" wash solution contains significant amounts of soluble components. An algorithm successfully models this condition and is simplified to a single expression when the wash solution is a ""clean"" solution containing no solubles. The CCD calculation module is compared to operating data from uranium and nickel-cobalt CCD circuits.IntroductionHydrometallurgical process schemes have often relied on countercurrent washing methods to reduce soluble losses of valuable product in the tails. Commonly used equipment to effect this operation is a CCD circuit of N thickeners in series, where a slurry is fed to thickener I and a wash solution to thickener N; clear pregnant solution overflows thickener I and washed tails exit as underflow from thickener N. CCD circuits of this type are typically employed when the solids tend to slime heavily and where a filter is not economic.A typical CCD circuit usually employs from two to five thickeners and can employ either a ""clean"" washing solution of, say, pure water or else the hydrometallurgical circuit may generate a ""dirty"" barren solution containing an appreciable amount of soluble component which may be advantageously returned to the process as CCD wash solution. Various authors have treated the case for clean washing solutions (Svarkovsky 1977, Merritt 1970). For the case of dirty wash solutions, an algorithm has been developed to enable efficient modelling by the BEMSIM computer program, because the need for an accurate method to calculate soluble losses is required when performing an economic trade-off analysis of the value of product lost in the tails as a function of the number of thickeners."

Jan 1, 1990

By Norman A. Parlee

Introduction The principal primary iron and steel producing capacity of the Dominion Steel and Coal Corporation is at the Dominion Iron and Steel, Limited, plant at Sydney, Cape Breton Island, Nova Scotia. The main raw materials are Cape Breton coal, Wabana (Newfoundland) iron ore, and Port-au-Port (Newfoundland) limestone. This plant, which was established at the turn of the century has gradually expanded its production facilities so that today its ingot producing capacity is over 720,000 tons annually. Principal operating units of the plant at present are three batteries of 173 Koppers by-product coke ovens with conventional by-product recovery equipment, three blast furnaces .of 15 ft. 6 in., 18 ft. 3 in., and 19 ft. 3 in. hearth diameter (inside the brick), one 700-ton hot metal mixer, ten open hearth furnaces (two of 175-ton capacity, three 12 5-ton, five 60-ton), one 10-ton electric furnace, a 40-inch blooming mill, a billet mill, a rail mill, a tie plate mill, rod and bar mills, and a wire and nail mill. Extensive machine shops and an iron and brass foundry are also available for plant maintenance and repairs. This paper will describe developments during the past five years and those now in process. It will also briefly discuss research being done and indicate the direction of future development.

Jan 1, 1951

By A. Bauer, P. Katsabanis, M. Baker

The principal results from a previous paper presented at the Mine Accident Prevention Association of Ontario in 1987 (1) are summarized here. It is concluded that the selection of explosives in mines experiencing sulphide ignitions is important and that aluminized explosives should be avoided because of their high explosion temperatures and their detonation products. The duration of the blast is also critical and secondary blasts should not occur simultaneously with nearby priroa:ty blasts.

May 11, 1988

By A. D. Pittuck

Refractory minerals .containing uranium and columbium have been successfully treated at Queen's University, Kingston, to produce high-grade concentrates. Recoveries of over 90 per cent of the uranium and columbium have been obtained when treating concentrates containing euxenite, fergusonite, betafite, and pyrochlore. The processes ?consisted -of leaching the columbium with hydrofluoric acid, and the uranium with nitric acid, sulphuric acid, or sodium carbonate solutions. The leach liquors were extracted with organic solvents from which the values were stripped and precipitated, producing final products assaying 45 to 55 per cent Ob2O5 and 60 to 70 per cent U3Os.

Jan 1, 1958

By T. D. Chatwin

Acid rock drainage (ARD) is one of the most serious and potentially enduring environmental problems of the mining industry. High liability costs carried by many mining companies to cover potential obligations of ARD are a clear indication of the gravity of the problem. Unchecked, ARD can result in water quality impacts that could well be the industry's most significant financial and credibility risk. Effectively preventing acid drainage is a formidable challenge that requires the total commitment of the mining industry throughout the entire life-cycle of a mine. To achieve this commitment a strong business case for ARD prevention must be developed. This paper will address the elements of acid prevention and discuss their importance not only to the company but the entire industry as well. The International Network for Acid Prevention (INAP) is an industry-led group created to help meet this challenge. In 2009, INAP published the GARD Guide (www.gardguide.com), a web-base best practices guide for the prevention of ARD [1]. In this paper, the GARD Guide will be used to identify preventative actions for all mining industry stakeholders. It will, in turn, be used to estimate ARD management and mitigation value accrued to the company from ARD prevention, which will be used in developing a business case for acid prevention.

Jan 1, 2011

By B. I. Boyko

As part of the Ministry of the Environment's Resource Recovery Program, the Province of Ontario has constructed a $13 million "Experimental Plant for Resource Recovery" in Metropolitan Toronto. The technology and unit operations involved in the processing of municipal solid wastes at a rate of 40 tons per hour at this facility are reviewed. Shredding, air separation and classification, screening, magnetic separation and composting are some of the operations featured at this plant. Recoverable commodities expected include paper, ferrous metals, an air-classified light fraction (shredded paper and film plastic), glass and compost. Existing and potential markets for these materials are discussed.

Jan 1, 1978

By G. V. Sirianni, G. E. Viens, R. A. Campbell, G. N. Banks, R. L. Sachdeva

"A combined shaft-electric furnace for the smelting of ores and the melting of metallized iron pellets is being developed. The materials are preheated, and in some cases pre-reduced, in the shaft before being transferred to the electric furnace, where melting or smelting is completed. It has been demonstrated that this combination of equipment will enable much of the relatively expensive electrical energy to be replaced by cheaper energy in the form of oil or natural gas, and preliminary experiments indicate that the total energy requirements for a melting or smelting operation are significantly reduced. Projections based on results obtained from the preliminary experiments indicate that further improvements will be possible when certain modifications to the equipment are completed."

Jan 1, 1968

By M. Pelser, H. Gous, J. H. W. M. Brits, K. Voogt

The effect of impurities; iron and selenium, on current efficiency and deposit quality in copper electrowinning was investigated using an at-line cell at the Rustenburg Base Metals Refiners’ Copper Tankhouse. The tankhouse is a direct leach, starter sheet electrowinning operation with a unique electrolyte composition. The effect of iron on the current efficiency in the at-line cell was found to be less severe than reported in literature. However, the distinction between the chemical impact of iron on current efficiency and the physical impact of iron on a starter sheet operation needs to be realised. The effect of selenium on current efficiency and deposit quality is also reported. INTRODUCTION Anglo American Platinum’s Rustenburg Base Metals Refiners’ (RBMR) Copper Tankhouse serves a unique function in the refinery flowsheet in that its primary functions are the removal of copper and production of acid for the leach circuit. This function needs to be performed to specification in order to keep the leach circuit operating optimally. Current efficiency is seen as an indicator of tankhouse performance and efficient energy use. The tankhouse plates starter sheets onto titanium blanks which, after stripping and preparation, return into the production cells for further plating. Approximately 78% of tankhouses surveyed (Robinson et al., 2013) use permanent cathode technology whereas older, smaller operations still use starter sheet technology. Drawbacks of the starter sheet technology are that the starters are thin and bend easily leading to increased shorts, they need to be removed after two days of plating to be manually straightened and are then returned to the cells. In addition, the electrolyte levels in the cells need to be adjusted during the plating cycle to improve loop adhesion to the cathode and reduce loop corrosion. The starter sheet technology is therefore very labour intensive and the final quality of the product is dependent on the quality of the starter sheets produced. In comparison, permanent cathode or direct plating technology lends itself to automation, allows for higher current densities and better cathode quality due to more robust geometric stability in the cell. The present barrier to implementation of permanent cathode plating at the RBMR Copper Tankhouse is the capital cost required to convert the tankhouse, i.e. blanks and stripping machine. At present, alternatives to titanium blanks, such as LDX 2101, are being investigated for the unique electrolyte composition of this tankhouse.

Jan 1, 2019