Search Documents

By C. Fortin

ABSTRACT The subject of gold flotation has been reviewed extensively. Most of these reviews focus on the theories of gold flotation and the physical and chemical effects that may impact the efficacy of the gold flotation process. The current status of gold flotation chemistry as it is being applied in industry has not been widely addressed. This paper reviews current gold flotation practice and research advancements and discusses how these applications tie in with the current understanding of gold flotation chemistry. Survey results from worldwide gold flotation operations are analyzed. Potential future areas of gold flotation research are highlighted.

Jan 1, 2013

By S. A. Pence, A. I. McCallum, V. de Korompay

"Special salt protection rings containing a water-swell• able, polymeric sealant are in successful operation in Canadian potash shafts. Installed above the Prairie Evaporite salt formation at a depth of 3,000 feet, the sealant is preventing formation water migration into the salt and pressure build-up on the concrete lining of both production and service shafts. The salt protection rings are not under the hydrostatic pressure of the formation water.The chemical sealant in use has the unique property of imbibing water and swelling. •Therefore, any water at• tempting to flow by the seal ring actually produces a tighter seal.The purpose of this paper is to discuss the sealant and its properties and uses. Installation of the material and its operation in two Canadian mine shafts is described."

Jan 1, 1971

By John Shirokoff, Ladan Khaksar

"Cyclic polarization technique and also potentiodynamic measurements were applied to study corrosion behavior of 13% chromium steels in chloride containing environment. Potentiodynamic measurements were performed at 25 and 75 °C with 0, 10 and 20 g/l NaCl in 0.01 M hydrochloric acid solution. At the same time, the significant pitting parameters such as corrosion potential (Ecorr), pitting potential (Epit), protection potential (Epro) and passive current (Ipass) of cyclic polarization curves with various NaCl concentration were analyzed and compared to describe the corrosion behavior of 13% chromium stainless steel. Surface measurement techniques such as SEM and EDS were used for morphology and analysis of corrosion products. The results showed that both temperature and Cl- concentration had significant effects on corrosion behavior of 13% chromium stainless steel in acidic solution.INTRODUCTION Of all the corrosion resistant alloys (CRA) used in oil and gas developments, martensitic stainless steels (MSS) are some of the most common ones these days. These steels not only have the advantages of normal steels: high strength, cost-effective, easy to manufacture, available in a wide variety of product forms, but they also have good CO2 corrosion resistance at higher temperatures as a result of their 11% minimum chromium content. One of the most common types of MSS used in the oil and gas industry is 13% chromium steel. NACE and API standards both reference several different varieties of 13% chromium steels for use in oil and gas projects(“Corrosion Resistant High Cr Steel for Oil and Gas Wells,” 2013). All types of 13% chromium steels have about 12 to 14% chromium and other minor alloying additions, and can be placed into two general groups: conventional and modified. Conventional 13% Cr steels (13Cr) are those most common in oil and gas, some of which are CA6NM (UNS J91150), AISI 410(UNS S41000), and AISI 420 (UNS S42000). These alloys have excellent corrosion resistance when compared to carbon steels up to about 300°F (150°C) and are used for a variety of wellhead, tubular, and downhole components however they have very limited resistance to cracking in H2S (Vallourec Group, 2015). Modified 13% Cr (M13Cr) steels came from the need for increased corrosion resistance at higher temperatures, increased H2S cracking resistance, and increased yield strength above 85 ksi (586 Mpa) primarily for tubular goods and other downhole equipment. These features were developed by taking a conventional 13Cr steel and adding nickel (Ni), molybdenum (Mo), copper (Cu), and other alloying elements. M13Cr provides better corrosion resistance than 13Cr up to about 350°F (177°C), yield strengths up to 110 ksi (758 Mpa), and also improved H2S cracking resistance(“Corrosion Resistant High Cr Steel for Oil and Gas Wells,” 2013)."

Jan 1, 2017

By H. A. Hamza, J. Visman

"This is a report on the combined application of ""long-chain"" flocculants and classifier cyclones in the field of slimes treatment, with emphasis on the simultaneous thickening and clarifying of industrial effluents, at low cost. The principle of the process described below involves: (1) the formation of small floes of relatively great strength, by sequential dispersion and conditioning, with average floe size of about 1501 microns; (2) the floes being of sufficient strength to withstand the shearing forces operating within a cyclone and consequently behaving as solid particles with an equivalent diameter (Stokes) that exceeds the size cutpoint of the classifier cyclone; (3) the removal of flocculated solids by means of a classifier cyclone the size cutpoint of which permits effective separation of these solids from the water. Results of test work to date indicate that a broader use of cyclones in industry is possible with the above types of flocculants because the submicron particles and colloidal material are readily collected and clear water is produced, with the attendant advantages of compact construction and low cost that are characteristic of centrifugal separation. The process generally permits classifier cyclones of medium throughput capacity (e.g. 12-in. diam.) to be used for clarifying effluents that contain minus 10-micron particles."

Jan 1, 1973

By R. C. Gegg

The property of MacLeod-Cockshutt Gold Mines, Limited, is in the Little Long Lac area of the Thunder Bay Mining Division, Ontario, about four miles south of the Canadian National railway station of Geraldton. The town of Geraldton is about 170 miles east of Port Arthur and 22 miles west of Long Lac, which is on the main line of the Canadian National railway. The Trans-Canada highway passes through the property and during the winter season the road is maintained between Port Arthur and Long Lac. Electric power is supplied by the Hydro-Electric Commission of Ontario from their Cameron Falls plant and is distributed at 44,000 volts by a local transformer station. Early History The South orebody was discovered by diamond drilling in the spring of 1936. This is a porphyry contact orebody with major pyrite and minor arsenopyrite mineralization. Some gold is present in the 'free' state, but for the most part it is locked in the pyrite, with little or none in the arsenopyrite. Preliminary test work was based on comparing straight cyanidation with bulk flotation and cyanidation of the concentrates. The overall results by the two methods were found similar, but for economic reasons the flotation-cyanidation process was adopted. Before the mill came into operation, a new and entirely different type of orebody, consisting of massive sulphide lenses in banded iron formation, was discovered to the north of the existing workings. These bodies are an intricate mixture of pyrite and arsenopyrite, both carying gold.

Jan 1, 1949

By C. Larsen, R. A. Walker, A. Voth, C. Daoust

"The 3000 t/d mill at Hernia Gold Mines Inc. was commissioned in March, 1985. By Canadian standards the concentrator is highly automated, however, unlike the retrofit systems in many other plants, the Hernia process control system was installed during plant construction. This paper describes the Hernia control system beginning with system development (justification, architecture, start up, etc.), proceeding to current applications (crushing, grinding, leaching, etc.) and finally discusses some of the short term objectives for system improvement.INTRODUCTIONThe Hernia Gold Mines Inc. operation is located in the Marathon area of Northwestern Ontario. Controlled by Noranda Minerals Inc. (50.1 %), the cost of bringing the mine into production was nearly $300 million. A unique feature of the mine development was the extraordinarily short elapsed time of three years from Noranda's initial involvement to the start of milling operations. Additional background information on this project can be found in the trade literature (e.g. Tinter (1986). Scales (1987).)The Hernia concentrator is designed to process 3000 tpd of ore and commenced operation in March, 1985. Figure 1 provides a general plant flowsheet indicating the major circuits. Typical annual production statistics are included on the figure and these have been extrapolated from the available 1987 year-to-date data. Larsen and Tessier (1986) have previously described the operational aspects of the mill.In a metaphorical sense, the Hernia concentrator is like the traditional bride, ""wearing something old (e.g. the cyanide leach process), something new (e.g. a plant wide digital control system installed during construction), something borrowed (e.g. crushers from Gaspe) and something blue (e.g. the cladding on the surface buildings). While the prospect of fully undressing this bride is of considerable interest, here we choose to focus on something new. In particular, we choose to examine the process control system in some detail since Hernia is one of Canada's more highly autcmated gold mills. The control system is of interest because it has received suostantial credit for maximizing metal production and minimizing operating costs. With reference to the latter, it is worthy of note that Hem lo reports recent operating costs of less than $100 U.S./oz."

Jan 1, 1988

By G. Paillard, I. E. Puddington, A. F. Sirianni, F. W. Meadus

Experiments with some selected Nova Scotia coals and a single sample of American anthracite, reconstituted in granular form with lower sulphur and ash contents by spherical agglomeration methods, are described. The effect of different bridging liquids, grinding times, gangue depressents and modes of agitation on the final product are discussed. The application of agglomeration techniques as a means of drying wet coal fines is also noted.

Jan 1, 1968

By R. Ichimura

This paper summarizes the results of a five-year project, which aimed at improving the current method to process the arsenic-bearing smelter dust of El Teniente. This project, which was started in 2001, was carried out jointly by JOGMEC (Japan Oil, Gas and Metals National Corporation) and CIMM (Centro de Investigación Minera y Metalurgica, Chile), and was financially supported by the Japanese and the Chilean governments. In the new process, the smelter dust is leached with sulfuric acid to dissolve arsenic, which is subsequently precipitated as crystalline ferric arsenate (scorodite) at ambient pressure by controlling the crystallization and crystal growing stage. As a result, a stable form of ferric arsenate is obtained, which passes the U.S. E.P.A. TCLP limit of 5 mg/L As. Copper and zinc are subsequently recovered from the arsenic-free solution. The copper product can be fed into the main copper production circuit at the Las Ventanas Smelter and Refinery, whereas zinc is recovered as a marketable product. A demonstration plant was installed and operated at CODELCO's Las Ventanas Smelter and Refinery. The basic and detailed engineering design was prepared by Mitsui Mining and Smelting Co. Ltd (MMS) on the basis of a joint study done by JOGMEC, CIMM and CODELCO's Las Ventanas Division.

Jan 1, 2007

By R. W. Bruce, K. W. Downes

"IntroductionSULPHUR production in Canada from all sources for the year 1953 amounted to about 375,000 tons. Except for 16,000 tons of elemental sulphur derived from natural gas, this production was in the form of by-product pyrites, liquid sulphur dioxide, and sulphuric acid. In the same year, Canadian industry imported 359,000 tons of elemental sulphur from the United States. The cost, including transportation charges, to Canadian consuming plants ranged from $35.00 to $45.00 per long ton, depending upon location.Although most of the sulphur consumed is used in the oxidized form it is often most convenient to buy sulphur in the elemental form, and convert it to sulphur dioxide or sulphuric acid in situ as required. This is because elemental sulphur is easily shipped and stored, weighs only half as much as an equivalent quantity of sulphur dioxide and one-third as much as the corresponding quantity of sulphuric acid, and is readily converted to these forms in a sulphur burner. A process, therefore, which could economically recover elemental sulphur from sulphide ores would be most attractive.Since the turn of the century, notable improvements have been made in extractive metallurgy, but until recently only limited attention has been paid to the possibilities of elemental sulphur recovery. This has been due to the plentiful supplies of cheaply mined Frasch sulphur which have been available on the world markets."

Jan 1, 1955

By D. B. Dreisinger, M. Mokmeli, B. Wassink

Dissemination of selenium and tellurium in sulphide minerals results in the contamination of pregnant leach solutions and electrolytes in the hydrometallurgical treatment of sulphide ores and residues. The selenium and tellurium content of the copper sulphate-sulfuric acid solution may be reduced into insoluble precipitates of copper selenides and tellurides using cuprous ion. This study presents the use of the thermodynamics and kinetics for the removal process of selenium and tellurium in real life application. Dominant species of selenium and tellurium in acidic copper sulfate solutions were identified and the reduction rates of species were compared. The findings were applied to industrial conditions by modeling the Vale’s CRED (Sudbury, Canada) plant’s selenium and tellurium purification circuit. Rate reducing factors on selenium and tellurium removal were identified and discussed.

Jan 1, 2014

By Melvin S. Taylor

The environmental control program at Cassiar Mine is an active one involving government, unions and company personnel all working together to achieve a goal- "A clean and safe working environment". This can only be achieved by utilizing three of Cassiar's most important resources; i.e., people, time and money. Past environmental programs have more than proved that the goal can be reached and. with the future programs now in progress. Cassiar Asbestos will achieve its environmental goals.

Jan 1, 1978

By Chris M. Healey

"Abstract - Perhaps the single most significant variable in the evaluation of a mining project is the reserve estimate. Many parameters are considered when estimating reserves, among them geology. This paper examines the link between the quality of a reserve estimate and a good understanding of the geological controls for the deposit. A clear understanding of the geometry is essential to the accurate definition of the shape and size of the deposit. This includes the definition of any structural controls as well as the proper interpretation of the stratigraphy. Further when the distribution of grades is erratic and there is consequently a high nugget effect, there are significant problems in estimating the true grade of the deposit.Two Saskatchewan examples are presented, one with good knowledge of the controls and therefore good estimates of reserves, and the other with a poor understanding of the geology and resultant problems in deriving good estimates. In both cases the reserve estimates at various stages in the project development are compared to actual results from underground work. The first example is the Star Lake Mine where just about all the estimates were within 10% of the actual on both tonnage and grade. The Laurel Lake deposit is discussed to show how problems in interpreting the geological data make reserve estimation very difficult. Laurel Lake has the additional problem of erratic grade distribution."

Jan 1, 1992

By E. W. Williams

THE Ontario Research Foundation has developed a process for producing low-density steel shapes by direct reduction of iron oxide powders. The process is a combination of reduction, sintering (without compaction), and carburizing, and has been described by Cavanagh (1). Iron oxide powder, in the form of mill scale or highly concentrated iron ore, carefully sized, is poured into a porous mould. A reducing agent, generally coke breeze, is placed around this mould in a heat resistant sagger which is sealed off and heated to 2,000°F. for a number of hours. The coke/ ore ratio, the particle size distribution, the temperature and time of soaking, and the size and shape of the reduced product, determine the densities and carbon contents attained. The Defence Research Board sponsored a programme of research into some of the mechanical properties of the material (which was named Controlled Density Steel) and this paper is an account of various factors which govern the tensile strength of the steel. The ?practically attainable range of density is from 1.5 to 5.5 gm./ cc. but higher densities are obtained on hot working. This paper, however, is restricted to discussion of results for moulded products.

Jan 1, 1957

By T. Senga, T. Namihira, S. Terada, S. Owada

"Electrical disintegration (ED) has been well known as a good comminution method to improve liberation of compositional phases because it was reported that electron avalanche could occur preferentially at phase boundary. But the detailed mechanism of the ED has been still not known. This paper describes the results of ED experiments using synthetic binary sample, copper/resin, under the conditions of various distance between electrodes, and discusses the energy distribution in the three kinds of phenomena in the ED process, which are(1) streamer progression in water, (2) electron avalanche in water, and (3) electron avalanche in solid sample, by measuring current and voltage with elapsed time. Then, it has been found that the energy distribution in the phenomenon (1) is quite low and that the distribution in the phenomenon(2) had a considerably large compared with that in the(3), which indicates that the shockwave generated in water could contribute much to the sample breakage.INTRODUCTIONElectrical disintegration (ED) has been well known as a specific comminution technology which enhanced selective breakage at phase boundary and lead to a good liberation among compositional phases1-6),but the detailed mechanism has not been clarified yet. This study describes energy distribution among the phenomena in the ED process by using a synthetic binary sample, copper/resin, the phenomena of which are (1) streamer progression in water, (2) electron avalanche and shockwave generation in water and (3) electron avalanche in solid sample usually at phase boundary. The energy distribution could be calculated from ED experiments and from voltage-current changes between electrodes as a function of elapsed time.SAMPLE AND EXPERIMENTALSampleThe sample used in this paper was a synthetic binary solid of copper/resin as shown in Figure1.Cut and polished pure copper lump was put into silicone mold and melted epoxy resin was poured into it and cooled, then, finally the binary sample was polished and molded in the form of 10 mm * 10 mm * 10 mm."

Jan 1, 2017

By A. Hynes, T. Skulski, D. Francis

The Archean volcano-sedimentary succession in the LG-3 area has undergone two phases of deformation and has been metamorphosed to upper greenschist and amphibolite facies. Marine, fine-grained sediments and mafic pyroclastics comprise the lowest observed stratigraphic unit. These sediments are overlain by a thick sequence of submarine basalts and minor basaltic andesite. The lavas are characterized by high Al/Al+Si, Ti values, low Mg numbers and flat REE profiles (lOx chondrite). A sedimentary prism of coarse elastics which was deposited close to an exposed plutonic highland, overlie the volcanics. Massive lavas of basaltic andesi te and associated volcano-sediments comprise the uppermost stratigraphic unit. These lavas are characterized by high Mg numbers, Ni, Cr, LREE (lOOx chondrite) but low Ti, Al/Al+Si and HRee. The supracrustal rocks were intruded by tonalites and tonalitic gneisses.

Jan 1, 1984

By Lawrence Bragg

WE associate metals with hardness, toughness, and strength. But a curious paradox lies at the root of the valuable mechanical proper-ties of the metallic state: in order to be strong, a metal must be weak. This paradox, and the equally surprising fact that, in a sense, metals are not true solids at all, are among the topics here discussed by Sir Lawrence Bragg. (1) WHAT METALS MEAN TO US We employ various materials to build or fabricate the many objects we use in everyday life, choosing those whose properties are most suitable for the purpose which the object has to serve. Certain of these materials have been used from the earliest times, such as stone, wood, leather, and animal or vegetable fibres, each with its own peculiar valuable properties. Stone resists crushing and is very durable and permanent, as indeed it must be, since it has so long resisted change as a part of-the earth's crust. It is there-fore ideal for walls and buildings, and very early in his history man discovered how to make artificial stones by burning clay, with the advantage that they could be given any desired shape, and made into bricks or given elaborate forms as pottery. Wood is strong and tough and light, it resists tension as well as compression, and is nor brittle like stone. It forms beams and furniture and parts of tools or weapons. Leather is tough but at the same time iris flexible; it is ideal as straps or sheers. Vegetable fibres such as linen or cotton, and animal fibres such as wool and silk, owe their value to their flexibility and strength in resisting extension. They can be spun into yarn or rope, and woven into cloth. The technological age in which we are now living is replacing the natural products used by early man by a series of artificial products, but it is remarkable to see how in nearly every case we are copying Nature's materials. The wide use of concrete represents a developed art of making artificial stone. Artificial fibres such as rayon or ?nylon replace cotton, wool, and flax. Plastics are coming very much to the fore; they correspond to early man's use of horn, another substance with peculiar properties of roughness in all directions without the 'grain' of wood. For the most part we are following in the footsteps of our remote ancestors, though we can make for ourselves what they had to cull from wood and field. There are exceptions; for instance, we have discovered comparatively recently the number of uses to which natural rubber can be put, and are now making it artificially. This is a really new discovery; our ancestors had nothing with such remarkable powers of elastic stretching without breaking, and resistance to being abraded.

Jan 1, 1943

By R. V. Fox, L. K. Sinclair, D. L. Baek

"In this study, rare earth elements were recovered from bastnasite concentrate and waste fluorescent lamp phosphors using supercritical carbon dioxide extraction with a nitric acid/tributyl phosphate adduct. Several pretreatment methods were used to alter the crystal structure of the source materials, and thus improve rare earth element recovery. Pretreatment methods included 1) dry roasting of the source material at 730oC, 2) decomposition with 50% sodium hydroxide solution at 150oC for 4 hours, and 3) decomposition with 12 M sulfuric acid at 300oC for 4 hours. Treated and untreated samples underwent supercritical extraction at 24 MPa and 65oC for 1 hour. Untreated bastnasite and phosphor samples showed <10% rare earth element recovery, but sodium hydroxide digestion resulted in >60% recovery for most rare earth elements. Dry roasting of the bastnasite concentrate was also effective, resulting in >60% recovery for cerium.INTRODUCTIONRare earth elements (REEs) consist of the 15 lanthanides, scandium, and yttrium. Scandium and yttrium are included because they are in the same group as lanthanum, appear in many of the same ore deposits as the rest of the lanthanides, and exhibit many similar chemical properties. REEs are used in a wide array of applications including electronics, magnets, catalysts, glass, and solid-state lighting (Xie, Zhang, Dreisinger, & Doyle, 2014). Because of China’s continued dominance of worldwide REE production, the United States Department of Energy has sought to diversify domestic supplies of REEs (United States Department of Energy, 2011). A key part of this strategy is the development of improved extraction methods for both ores and recycled sources.Supercritical fluid extraction (SFE) is a promising technology for extraction and separation of rare earth elements. Contact with an acid adduct dissolved in supercritical carbon dioxide allows for the rapid extraction of REEs from solid matrices. Supercritical CO2 has several potentially useful properties as a solvent, including high diffusivity and the ability to tune solvation properties by adjusting pressure. Such tunability may have applications in separating the REEs once they have been extracted from the solid phase. Tributyl phosphate/nitric acid adducts (TBP:HNO3) are a particularly promising class of adducts for SFE extraction of rare earth elements. Using TBP:HNO3 adducts in supercritical CO2, several researchers have successfully extracted REEs from their oxides (Wuhua, Pijia, & Yongjun, 2010; Zhu, Duan, Xu, & Zhu, 2009). However, there is a complication in applying this technique to many types of ores and recycled sources: REEs are often locked in refractory minerals which are resistant to acid attack, resulting in limited recovery in supercritical extraction."

Jan 1, 2016

By R. Rumpold, J. Antrekowitsch

"The continued increase of the automobile production leads to a higher platinum, palladium and rhodium (PGM) demand. Due to the high value of the PGMs the recycle of these metals from automotive catalysts is of special interest. Pyrometallurgical processes, which are only focused on the PGMs, represent the state of the art of automotive catalysts recovery. However, hydrometallurgical recycling processes offer additional recovery of other valuable metals and compounds. The method presented in this paper is based on a combination of hydrochloric acid and hydrogen peroxide to dissolve the valuable metal fraction which can be precipitated afterwards.INTRODUCTIONPlatinum and the corresponding metals from the PGM group, especially palladium and rhodium are well known as catalytic active materials. They support chemical reactions which are inhibited. This effect is used to decrease the amount of harmful compounds like hydrocarbons, carbon monoxide or nitrogen oxides in automotive exhaust gases. The generation of these toxic substances is based on incomplete combustion, which in turn is caused by non-ideal conditions in the combustion chamber. Catalytic converters minimize the harmful compounds by supporting the following Reactions 1 – 3 (Votsmeier et al., 2009).CO + ½ O2 ? CO2 (1)CnHm + (n + ¼ m) O2 ? n CO2 + ½ m H2O (2)2 NO + 2 CO ? N2 + 2 CO2 (3)Platinum and palladium are very effective for the oxidation (Reactions 1 and 2), while rhodium supports the decomposition of nitrogen oxides by carbon monoxide (Votsmeier et al., 2009). The classical three way catalyst was a platinum – rhodium combination with a Pt:Rh ratio of 5:1 (Hagelüken et al., 2005). Today the platinum, palladium and rhodium ratio is highly variable and strongly depends on the engine type as well as on the car producer. Diesel engines are operated with a super stoichiometric air addition in comparison to spark ignition systems. Therefore the exhaust gas composition and off gas temperature is different. Based on the high oxygen amount, diesel engines produce less carbon monoxide and hydrocarbons but more nitrogen oxide in contrast to gasoline engines. This leads to various requirements for the catalytic converters."

Jan 1, 2012

By C. R. Tang

Due to the current lack of sufficient occupational hazards supervisory staff in China, an occupational hazards supervision regulatory framework is proposed, based on the cloud. Data on respirable dust, noise, heat, toxic and hazardous substances and protection facilities are uploaded to private cloud computing data and service centers to build an occupational hazards supervision system. This system promotes occupational hazards governance. Complex reports are generated. Through the establishment of an occupational hazard supervision data threshold, the dynamic regulation of occupational hazards is accomplished. The main characteristics of this approach are low cost, ease of expansion and maintenance, and strong performance.

Aug 1, 2013

By Rita Awwad

Building Information Modeling (BIM) has been gaining a significant edge in the construction industry over the last decade. BIM allows gathering all building information in one shared database that can help all construction entities better understand, integrate and visualize all work progress from inception to operation of the building. The main purpose behind BIM is to bring all project participants together (Client, Architect, Contractor, Consultant) since the initial stages of a project allowing them to cooperate and work as a team in the promise of an increased productivity, reduced cost, enhanced quality and faster delivery. However, a full-fledged implementation of BIM tools and benefits is not yet achieved in the construction industry and remains a debatable issue for researchers and practitioners in the construction field. This paper aims at assessing BIM awareness and usage in the Lebanese construction industry through conducting interviews with contractors, architects and consultants that are key players in the Lebanese market. A comprehensive literature review about BIM adoption in some developed countries and in the surrounding region is also provided in order to better evaluate the Lebanese industry status in comparison with foreign industries. This research sheds the light on BIM awareness of the different construction parties in the Lebanese market, assesses the extent of its current use, identifies the pertaining implementation challenges, and provides recommendations to enhance BIM role in the Lebanese construction industry.

Aug 1, 2013