Search Documents

By Z. S. Shao, X. Z. Li

"Sub-critical crack growth plays an important role in long-term creep failure in brittle rock. Based on micromechanics established by using relationship between micromechanical wing crack growth model and macroscopic strain, and comparing theoretical model with testing results, a method, which applies the theory to real rock, is suggested in this paper. Using this method, properties of creep, damage and progressive failure in brittle rock are investigated. Effects of stress state on creep failure time and steady-state creep rate are analyzed and graphically presented. The results are helpful to support structure design and service life evaluation of underground structures with high geostatic stresses. INTRODUCTIONDuring the long-term operation in underground space with brittle surrounding rock, due to chemical action between pore water and rock, the failure of rock often occurs at stresses below its short-term failure strength, which brings serious effect on the long-term stability of underground structure. Thus, the long-term strength of brittle rock attracted wide interests of scholars around the world. The static fatigue limit was predicted by exponential function that is derived from abundant experiment data of stress level and failure time(Schmidtke & Lajtai, 1985), and similar result by relationship between stress state and failure time was also suggested (Lau & Chandler, 2004; Aubertin et al., 2000; Sangha & Dhir, 1972). According to relationship between steady creep rate and stress state during creep, a critical stress that transforms steady-state creep to accelerated creep was studied and the long-term strength was suggested (Tsai et al., 2008; Ma & Daemen, 2006; Lajtai et al., 1991). Based on the results of experiment in compression, the long-term strength of rock was defined by stress at volume strain reversal. When applied stresses are larger than the long-term strength, the microcracks in the rock will grow constantly, damage of rock will increase and failure of rock will occur finally (Chandler, 2013; Bieniawski, 1967; Brace et al., 1966)."

Jan 1, 2015

By A. Elsayed

Lightweight metals such as magnesium show potential in replacing aluminum alloy castings for engine cradles, cylinder heads and transmission cases. Unfortunately, magnesium alloys are susceptible to entrapping oxides and other impurities during casting that hinder strength and ductility. The current study examined various filter sizes and configurations with the aim of improving the mechanical properties of permanent mould cast AZ91E. The unfiltered casting had a yield strength, tensile strength and ductility of 93.3 MPa, 153.3 MPa and 2.2 % respectively and increased to 96.5 MPa, 167.0 MPa and 3.1 % with the use of a fine mesh filter within the well of the mould. The increased strength and ductility was likely due to the filtered castings containing fewer inclusions on their fracture surfaces as compared to the unfiltered castings.

Jan 1, 2011

By K. A. Foxford, D. A. Polya, R. P. B. Hebblethwaite

"Abstract-A variety of techniques for interpreting systems of mineralized echelon veins is discussed using examples from Panasqueira and SW England. As aids for exploration and mine planning, and as a tool for ore reserve evaluation, particular emphasis is placed upon establishing vein morphology in the third dimension, and upon understanding vein dilation and propagation histories. Special attention is also placed upon investigating vein thickness and spacing relationships, and upon understanding vein segmentation. The relevant data for these techniques are all readily obtainable from stope and core sources.The vein systems described were produced in host-rock sequences that underwent incremental dilation in response to fluid overpressures, and individual veins display evidence for mineral infilling synchronous with their propagation. Echelon vein geometries resemble those reported from igneous dikes and sills: vein walls are stepped and veins are divided into segments arranged in echelons. Changes in vein geometry, from arrays to composite structures, reflect both the evolution of the vein system with time, and the changes occurring between the margins (arrays) and core (composite structures) of the system. These characteristic morphologies can be used to infer vein propagation and fluid injection trends, proximity of neighboring veins, and the shape of the system as a whole. The techniques are applicable to systems of echelon veins produced under tensile conditions in rocks where faults were absent at the time of vein formation, and where subsequent deformation has been minimal. Further work is required to assess the application to echelon vein systems formed within more complex tectonic regimes."

Jan 1, 1995

By Peter N. Calder

The orientation of planes of inherent weakness (joints) with reference to an excavation in rock is the critical factor determining stability. The purely frictional 'residual' strength remaining following the breakdown of initial cohesion is the only strength which can be counted on to resist sliding for the long term. A simple method of resolving driving and resisting forces in three dimensions along joint intersections 'undercut' by the excavation is presented. Contrary to the case of slope failure in soils, it is shown how significant changes in the slope angle sometimes have no effect on the degree of stability pre-sent in rock slopes. Wall control by reorientation of the slope, the use of cable bolts and water diversion are briefly discussed.

Jan 1, 1970

By K. Huang, L. Pan

"Darcy’s law has been used extensively to model cake filtration. It is a macroscopic model, in which particle size dominates the kinetics and cake moisture. In the present work, a capillary flow model has been developed from first principles to study the effects of microscopic parameters such as capillary radius, boundary layer slip, disjoining pressure, and surface tension that may be important for dewatering ultrafine particles. Laboratory-scale pressure filtration tests show that dewatering kinetics is strongly dependent on capillary radius, which in turn is influenced by surface hydrophobicity, surface charge, and length scales of particles. The model parameters determined from laboratory-scale filtration tests show that use of a hydrophobizing reagent can greatly improve fine particle filtration due to increased slip and decreased capillary pressure. The kinetics of dewatering kaolin clay is fastest at a pH where the layer-structured particles coagulate with a face-to-edge orientation. The capillary flow model developed in the present work may be useful for designing filters and optimizing operating conditions.INTRODUCTIONIn 2014, Canada produced 2.2 million barrels per day of crude oil from the oil sands resources in Alberta, which is expected to grow to 3.2–4.0 million barrels per day by 2030 (CAPP, 2013). One of the challenges to meeting these projections is the tailings management. At present, the industry uses ?77 km2 of the lands to construct tailings ponds. Significant amounts of the tailings disposed to the ponds are silts and clays that are slow to settle and consolidate, creating problems for reclamation. It is, therefore, the objective of the present work to develop a filtration model that may be useful for developing advanced dewatering technologies that can address the tailings management issues.Darcy’s equation is the governing law for filtration. It was derived as an empirical model by H. Darcy in 1856 while he was studying fluid flow in sand filters (Hall, 1956). Since then, many investigators derived it from first principles. It relates superficial fluid velocity to the pressure drop across a porous medium of known permeability. In filtration, the latter can be related empirically to particle size using the Kozney equation (Yoon, 2005)."

Jan 1, 2016

By K. A. Foxford, D. A. Polya, R. P. B. Hebblethwaite

"A variety of techniques for interpreting systems of mineralized echelon veins is discussed using examples from Panasqueira and SW England. As aids for exploration and mine planning, and as a tool for ore reserve evaluation, particular emphasis is placed upon establishing vein morphology in the third dimension, and upon understanding vein dilation and propagation histories. Special attention is also placed upon investigating vein thickness and spacing relationships, and upon understanding vein segmentation. The relevant data for these techniques are all readily obtainable from stope and core sources.The vein systems described were produced in host-rock sequences that underwent incremental dilation in response to fluid overpressures, and individual veins display evidence for mineral infilling synchronous with their propagation. Echelon vein geometries resemble those reported from igneous dikes and sills: vein walls are stepped and veins are divided into segments arranged in echelons. Changes in vein geometry, from arrays to composite structures, reflect both the evolution of the vein system with time, and the changes occurring between the margins (arrays) and core (composite structures) of the system. These characteristic morphologies can be used to infer vein propagation and fluid injection trends, proximity of neighboring veins, and the shape of the system as a whole. The techniques are applicable to systems of echelon veins produced under tensile conditions in rocks where faults were absent at the time of vein formation, and where subsequent deformation has been minimal. Further work is required to assess the application to echelon vein systems formed within more complex tectonic regimes."

Jan 1, 1995

By Ltd. (CYMCO) Technology Center Yunnan Metallurgical Group Co., S. Jian, T. Song, J. D. Miller

"As sulfide zinc ore deposits become exhausted, nonsulfide zinc ore deposits become the other resource for zinc production. However, flotation for zinc recovery from nonsulfide deposits is much more difficult than the flotation of sphalerite from sulfide deposits and may become an option for zinc production only if a suitable processing technology is developed. In this regard, research efforts are being devoted to the flotation of nonsulfide zinc oxide minerals. Some common methods which have been used for the flotation of zinc oxide minerals include sulfidization-flotation, activation, and direct flotation with anionic and cationic collectors. The traditional flotation techniques have low efficiency and difficulty in separation and recovery of the zinc minerals from gangue minerals, for example, smithsonite (ZnCO3) from other carbonate gangue minerals and hemimorphite (Zn4Si2O7 (OH)2·H2O) from silicate gangue minerals. In this study potassium lauryl phosphate was evaluated as a collector for the flotation of nonsulfide zinc minerals. Results from contact angle and microflotation experiments at pH 6–9 show that hemimorphite (Zn4Si2O7 (OH)2·H2O) can be floated from quartz and that smithsonite (ZnCO3) can be floated from calcite. However, when dodecylamine, which is a common collector reported in literature for the flotation of nonsulfide zinc minerals, was used as collector, no significant difference between nonsulfide zinc minerals and gangue minerals was observed at any pH value. Initial evaluation suggests that potassium lauryl phosphate is effective at low concentration and may be a promising collector for zinc oxide mineral flotation.INTRODUCTIONBefore the twentieth century, zinc was mainly produced from nonsulfide ores (Large, 2001; Gilg, Boni, & Cook, 2008). With the development of differential flotation processes in the late 19th century major production switched from nonsulfide zinc sources to sulfide zinc ores (Hitzman, Reynolds, Sangster, Allen, & Carman, 2003; Gilg et al., 2008). However, as it is becoming more difficult to find new sulfide ores, recovery from nonsulfide deposits is being considered. Nonsulfide flotation for zinc recovery is much more difficult than the flotation recovery of sphalerite from sulfide deposits and may become an option for zinc production if a suitable technology is developed. Zinc and lead oxide ores are difficult to beneficiate ores due to their similar floatability with gangue, high solubility in water, and the influence of slimes (Fa, Miller, Tao, & Li, 2005). In order to improve the performance of oxidized minerals, lots of effort is being devoted to this field of study (Ejtemaei & Mahdi, 2014)."

Jan 1, 2016

By K. E. Waters, J. E. Nesset, F. Rosenblum, J. A. Finch

An advanced laboratory-scale weathering apparatus has been developed at McGill University to study the effects of weathering (ambient temperature oxidation) on the self-heating of sulphides. Previous work by the authors has shown that the problematic self-heating of sulphides is inherently linked to the degree of oxidation (weathering) of the minerals: un-oxidized active sulphides exhibit little or no self-heating while the same material when weathered can generate extensive self-heating bringing temperatures well above 100 0C. In this study the effects of environmental conditions (weathering time, ambient temperature, sample moisture, relative humidity, and oxygen content) were evaluated with respect to the self-heating response of a pentlandite-pyrrhotite nickel sulphide concentrate.

Jan 1, 2015

By Hans Lundberg

PREFACE THE successful conclusion of all geophysical work depends on the operator's skill and sound judgment, as well as on his knowledge of geology and geophysics. We have been fortunate enough to have as co-workers a number of very good men. Some results of their work are summarized in this paper, and it is a pleasure to acknowledge their cheerful spirit of co-operation and the enthusiasm and loyalty with which they have assisted in the building of a geophysical organization to serve the Canadian mining industry HISTORY Geophysical prospecting is commonly, but quite erroneously, regarded as something new. The name is modern, but the principle of applying physical laws to reveal the presence of hidden ore is several hundred years old. Already, at the beginning of our civilization, the need was strongly felt for methods that could indicate the presence of ore in regions where the ore-bodies were completely masked or hidden from the eye. Particularly in countries where the rocks have been eroded during periods of glaciation and later covered by a thick mantle of glacial debris, all kinds of mysterious schemes were invented to locate the hidden ore. Often magic was resorted to (for example, the divining rod), but methods based on sound principles were also developed. Such features as topography, colour and taste of surface waters, and the growth and occurrence of trees and plants, were used to reveal certain types of ore deposits. For finding bodies of iron ore, the compass was very early in use. The fact that objects of iron attract a compass needle was utilized in prospecting long bef01:e the time of Columbus, and a systematic search for bodies of iron ore by this method was organized as early as the year 1600. There are still in existence documents, dated a little over 300 years ago, which show that the Swedish Chancellor of that day, Axel Oxenstiorna, ordered dozens of sun-dial compasses from instrument makers in Germany. The Swedish Government at that time employed a great number of prospectors to search systematically for iron ore. This Government undertaking must have been quite successful, as a number of iron ore-bodies were found in areas covered by heavy overburden. These prospectors were simply Government 'geo-physicists', although they were not known by this fancy name.

Jan 1, 1937

By Ifeanyichukwu Nweke

"Aluminium rolling processing from ingots to cold rolled coils comes with a lot of challenges especially in controlling defective products in casting, hot mill and cold mill operations. Hence this study focused on reducing defects at mills and cast-house using six sigma approaches. The use of six sigma approach will help the production experts to determine the gap between its operation and world class process. Practical data from First Aluminium Rolling mills were presented and analysed and mini improvement projects were proposed based on organisation need to achieve excellence. This study encourages aluminium alloy industries to pursue process improvement projects on the basis of analysis on data obtained from their shop floor, hence ensuring that through this, recovery is improved and cost of poor quality is reduced.INTRODUCTION Engineer Bill Smith while working at Motorola in 1986 introduced a new concept in which a set of techniques and tools are used for process improvement by controlling variations (defects). These tools and techniques are explained by an acronym DMAIC. D DEFINE the problem M MEASURE the variables in the problem A ANALYSE the variables of the problem I IMPLEMENT and verify the solution to the problem C CONTROL the solution to sustain it Most times in six-sigma approach, variations in the process that results in defects and customers’ dissatisfaction are targeted at 3.4 defects per million opportunities. There are numerous methods six sigma application use to achieve quality results and innovative strategies. Improving the quality of process through these methods helps identify and reduce variations which paves way for organisational excellence. In this study, it is encouraged to use six sigma techniques to improve aluminium rolling operations and other aluminium processing activities, the benefits of such improvement concept include: • Satisfy the voice of the customer (VOC) • Minimise costs • Maximise Profits • Build Good Team • Implement Profitable Project"

Jan 1, 2018

By A. Idegami, M. Imamura, S. Heguri, Y. Ozaki

"Nickel powder can be produced by the reduction of a nickel ammine complex solution by hydrogen at high temperature and pressure. To minimize the deposition of fine nickel on the surface of the reactor and other equipment, seed crystals are added to the initial solution to promote nucleation of the nickel powder. Such seed crystals catalyze the precipitation of the nickel particles on the surface of the seed and enhance grain growth. In this study, nickel nuclei were precipitated by the addition of a polymer to the nickel ammine complex solution, resulting in the production of nickel powder. Thus, we herein propose a model that explains the effect of the polymer in the precipitation of nickel nuclei.INTRODUCTIONNickel powder is commonly produced via a hydrometallurgical process from the hydrogen reduction of a solution containing a nickel ammine complex at high temperatures and pressures, and this process was commercialized in the 1950s by Sherritt Gordon (Sherritt International, Canada, Benson & Colvin,1973; The Staff, Research and Development Division, Sherritt Gordon Mines, Ltd., 1958).In the above transformation, upon the injection of hydrogen gas into the solution, nickel is reduced as outlined in Equation(1), ultimately resulting in the production of nickel powder.Ni(NH3)nSO4+ H2?Ni+ (NH4)2SO4+ (n-2)NH3(n:2–6)(1)In this process, seed crystals are added to the reactor to suppress the precipitation of fine nickel (scaling) and to enhance nickel reduction (Benson & Colvin, 1973; Mackiw, Lin & Kunda, 1957). More specifically, iron sulfate and a small amount of dispersant polymer are added, which leads to the formation of nuclei. Upon subsequent hydrogen reduction, the reduced nickel can then be deposited on the nuclei, allowing nickel particle growth to take place. However, this results in iron contamination in the final nickel product, and so the use of pure nickel as a seed crystal is desirable to produce high quality nickel powders."

Jan 1, 2017

By L. Tafaghodi, S. Sarbishei

"Following the depletion of nickel sulfide ores, laterites are considered as one of the main sources for producing nickel and cobalt. One of the primary steps in pyrometallurgical extraction of nickel from laterites involves partial reduction of the ore at temperatures below 1000°C. Studying the kinetics of laterite reduction provides valuable information on reducibility of nickel laterites using coal as a reductant. The present study investigates the reduction behavior of a nickel laterite by thermal gravimetric analysis and differential scanning calorimetry. Non-isothermal reduction tests and X-ray diffraction analysis were performed to find the main reactions that occur during the process. The kinetic parameters were calculated by Coats-Redfern method. The general model of simple reaction f(a)=(1-a)n was used for calculating kinetic parameters.INTRODUCTION Nickel (Ni) naturally occurs in the form of sulfide and laterite ores. Laterite ores are mainly available in tropical regions. Weathering phenomena during millions of years has led to the formation of several layers with specific mineralogy (Butt & Cluzel, 2013). The three main layers downward are limonite, smectite, and saprolite (Crundwell et al., 2011). Although laterites are the most available nickel ore resource (70%), their share in the overall Ni production is limited to 40% (Crundwell et al., 2011). The main reasons for not materializing the full potential of laterites are as follows (Ray et al., 1985): •,Laterite ores contain high water content (free and combined) which in turn results in high energy consumption of the extraction process. •,As Ni is present in the form of solid solution in laterites, physical upgrading methods such as flotation are not effective in increasing the Ni content before the extraction process. •,Extracting Ni from sulfide ores involve exothermic reactions which are beneficial due to decreasing the overall energy requirement of the process, however there is not efficient release of energy in the process of extracting Ni from laterite ores."

Jan 1, 2017

By Ralph W. Edie

"IntroductionTHIS PAPER presents some analyses of diabases from a number of metallogenic provinces in Canada and the United States. It is intended as a contribution to the literature on the genesis of mineral deposits associated with diabase.As it has been in the past, opinion today on the origin of the cobaltnickel- native silver and associated pitchblende type of deposit is sharply divided. Some geologists hold that this type of deposit is in some way genetically related to intrusive diabase; others are of the opinion that the deposits are related to granite. The controversy, like others of a similar nature, probably will not be settled satisfactorily for many years to come, •but in the meantime it is recognized that, with respect to most deposits of the type referred to, altogether too few facts are known for accurate conclusions on genesis to be drawn. To contribute in a small way to factual data on this whole .problem, the writer analyzed diabase from several districts in Canada in which deposits of the aforementioned type occur. For comparative purposes, the copper, cobalt, and nickel content of diabase from Cornwall, Pennsylvania, and of norite from the Sudbury basin of Ontario, was also determined.Insofar as is known, none of the analytical work undertaken had been previously carried out."

Jan 1, 1953

By M. Elmadagli

Wear mechanisms of two commercial aluminum alloys, namely a spray formed and extruded Al-25%Si alloy, and a sand cast A390 alloy (18.5 %Si) that are known to be successful in cylinder bore technology were studied to have a better understanding of the requirements for wear resistant aluminum alloy design. From durability point of view these alloys are known to be successful for engine bore applications. It is interesting to compare the wear mechanisms in these alloys because they have significantly different silicon content and microstructures, and were produced using different techniques. The wear tests were done using a block-on-ring configuration, in controlled air atmospheres (5 % relative humidity). In spite of the differences in silicon content and microstructure, the wear mechanisms were similar and consisted of formation and destruction of hard tribolayers that are either formed by either mechanical or chemical interactions on contact surfaces. The differences in the wear rates between the two alloys arose from the differences in the hardness of the worn surfaces, and the alloy's ability to sustain the tribolayers on the worn surfaces.

Jan 1, 2004

By W. Dingley, G. R. Hoey

"AbstractWear of six types of grinding balls was compared with and without corrosion inhibition in grinding Ni-Cu sulphide and hematite ores in laboratory ball mills. Forged steel balls (Rc 60 to 65) and three types of white cast iron balls (Rc 50 to 65) were susceptible to corrosive wear and two types of stainless steel balls [AISI Type 440C (Rc 65) and AISI Type 302 is; 35)] were relatively immune. The relative wear rates of the five types of hard balls (Rc 50 to 65) were dependent on the corrosivity of the ore. Ranking of the hard balls with respect to wear resistance was consistent for the sulphide and hematite ores in the presence of corrosion inhibition, whereas their ranking was different for the two ores in the absence of inhibition.The electrochemical potential of the grinding balls was measured during grinding and was found to be a useful measurement for assessing the susceptibility of an alloy to corrosive wear. Reduction of ball wear for forged steel and white cast irons with corrosion inhibition was concomitant with a shift of ball potential to less active values. Ball potentials in the presence of inhibition were indicative of non-corroding metal surfaces.IntroductionA PREVIOUS STUDY by the authors (1) showed that corrosion inhibitors - sodium nitrite, sodium chromate and sodium metasilicate - reduced wear of forged steel grinding balls by up to 49% in grinding Ni-Cu sulphide ore. Although the mechanism of wear reduction was not elucidated, it was concluded that corrosion must play a significant role in the wear of grinding media. Remark and Wick (2) of Battelle Pacific Northwest Laboratories have also evaluated corrosion inhibitors for the reduction of metal wear using abrasive and n on- abrasive te sting procedures. Their research was sponsored by 16 companies throughout the world. Preliminary results indicated that anodic inhibitors prevent from one-fourth to one-half of the loss due to corrosion."

Jan 1, 1977

By B. Tonn, F. Kröger

"The continued development in engine technology is leading to an augmentation in power density which steadily elevates the requirements for thermally and thermo-mechanically highly loaded components such as cylinder heads and pistons. Due to these high performance requirements conventionally applied Al-Si alloys have reached their application limits, since their mechanical properties deteriorate quickly under the influence of heat. Improved applicability is given by Al-Cu-based casting alloys which have a superior high-temperature strength than Al-Si alloys. Since Al-Cu alloys exhibit insufficient casting characteristics, especially regarding hot tearing susceptibility and increased tendency for porosity, it is currently not possible to cast geometrically complex components in robust permanent mold casting processes. The further development of Al-Cu alloys is aimed at finding an optimum between improved castability while high-temperature strength and thermal conductivity are not deteriorated. It is known that a high amount of eutectic reduces the hot tearing susceptibility of an alloy, but it reduces thermal conductivity at the same time. In this paper it will be presented how the conflicting objectives – improved high-temperature strength, good thermal conductivity and reduced hot tearing susceptibility – can be brought together to develop an optimized Al-Cu alloy for application in permanent mold casting.INTRODUCTION At the beginning of the 21st century car, engine blocks were primarily made of gray cast iron (GJL). Less than half a decade later, the choice of material had shifted towards lightweight materials. Ever since, the car engine manufacturing is dominated by aluminum-based alloys. The weight of car engine blocks could thus be reduced by around 50% due to the lower specific weight of aluminum alloys compared to gray cast iron. Furthermore, the high thermal conductivity of aluminum alloys allowed a reduction of complex cooling channel systems and thereby promoted the advancement of this material group. The further development in engine technology leads to an augmentation in power density which elevates the requirements for thermally and thermo-mechanically highly loaded components. For example, in diesel-powered car engines the upper required limits can reach an ignition pressure as high as 230 bar and gas temperatures of up to 1000°C. Thereby, thermal loads can cause high alternating thermal stresses (Grzincic, 2003) which can effectively be reduced by providing high thermal conductivity."

Jan 1, 2017

By Carol A. Pilon

"IntroductionRECENTLY, the Saskatchewan Research Council (Saskatoon ) marked the completion of one of its coal-related projects with the publication of the Bibliography and Index of Coal in Saskatchewan and Adjoining Provinces and States, hereafter referred to as the Bibliography and Index of Coal. Over a two-year time period, literature was surveyed and indexed and bibliographic data were compiled using a computer-assisted information retrieval system called FAMULUS. The final publication contains 1150 bibliographic references, which are cross-referenced by six indices.The project was initiated in September 1974, in support of Saskatchewan's Coal Resources Evaluation Program , an ongoing research program sponsored by the Department of Energy, Mines and Resources (Ottawa) and the Province of Saskatchewan. This program places emphasis on such areas of concern as the occurrence of deposits, chemical and physical properties, calculation of reserves and computer-assisted applications for the evaluation of lignite resources in the Province. Attention is also given to aspects of geophysical exploration, mining conditions and economics, by-products and the transporting of lignite. These are the subject areas .covered by the Bibliography and Index of Coal.The over -all objectives of the literature indexing project may be enumerated as follows: (1) to build a specialized resource library by surveying established public and specialized libraries, and commercial data bases; (2) to enter library data into the FAMULUS information retrieval system, to be used to generate bibliographies and indexes, and to retrieve information by the use of specified searching techniques; (3) to make this library data available to interested persons."

Jan 1, 1977

By S. Esfahani, M. Barati, Y. Kauwachi

"Heat recovery from slag has gained attention due to its high potential in lowering energy intensity of metal extraction processes. A direct method to recover the thermal energy of slag is to use countercurrent air flow that extracts the heat from falling droplets. Often, the solidified slag is aimed to be used as a substitute for Portland cement, thus high cooling rates are required to form an amorphous slag with sufficiently strong hydaulicity. Rapid cooling however involves using large gas flow rates that in turn lower the thermal efficiency of the process. This article presents a mathematical model that was developed to determine the optimum conditions in the heat recovery process and to investigate the effect of the air flow and granule diameter on the cooling rate of the droplets as well as the thermal efficiency of the heat recovery system. INTRODUCTIONMetallurgical slags are the largest by-product of high temperature materials refining and extraction processes. The total amount of metallurgical slag produced in the year 2008 has been estimated at up to 422 million tonnes containing up to 222 TWh/y (Barati and Esfahani, 2011) of thermal energy. Over the past four decades attempts have been made to recover this substantial amount of energy as heat, electricity, or fuel, while none of the proposed method has been commercialized yet.During slow cooling the slag tends to crystallize the constituents (CaO, SiO2, Al2O3, etc.) into a hard, heavy solid. In the past, over 90% (Bengt, 1983) of the molten waste was discharged onto heaps and allowed to cool slowly, then crushed and used in road construction or land filling or as coarse aggregate for concrete. However, later it was found if cooled rapidly, the slag can be used as a substitute for Portland cement. As a result, processes such as wet granulation were created in which molten slag is fragmented with water, forming amorphous (glassy) phases. Despite its effectiveness in producing a suitable material, heat would not be recovered through this process. Thus, dry granulation was introduced in 1930’s and was developed further in 1970 – 1980’s."

Jan 1, 2012

By J. W. Hohn

The precipitation of Fe(III) to form ferrihydrite in the presence of arsenic is the United States EPA's Best Demonstrated Available Technology for treating arsenic-containing hydrometallurgical solutions and waste streams. This technology has been widely adopted throughout the world and developments have been well reviewed. The adsorption and long-term stability of ferrihydrite can be improved by co-precipitating Fe(III) and Al(III) together to form an aluminum-modified ferrihydrite. Arsenate adsorption into ferrihydrite and modified ferrihydrite as a function of pH, Fe/As or (Al+Fe)/As mole ratio, and the initial As(V) concentration is presented and compared. The results of long-term aging of both adsorbents at 70°C for over a year are also summarized.

Jan 1, 2006

By Getu F. Biftu

There is general agreement among scientists that global surface temperatures have been increasing during the past decades. The increase in temperature is postulated to be the result of either an increase in greenhouse gases emission or climate variability (i.e., due to variations in sun or volcanic activity or El Nino and La Nina events) during past decades and may continue to increase. The effects of a predicted rise in the Earth?s surface temperature include an increase in average global evaporation and increase or decrease in precipitation (Bloomfield, 1992; Mann et al., 1991; Vinnikov et al., 1990; Gan 1995; Zhang et al., 2000a). The general circulation models (GCMs) project a global warming due to greenhouse effects of 1.5-4.5°C by the mid 2050s, with the most pronounced changes taking place in northern latitudes (Nicholls et al., 1996). However, similar predictions at a watershed scale or even a regional scale using GCMs are mot possible yet (Arnell et. al., 1996; Georgievskii et. al., 1996; Zhang et al., 2000a). Detection of historic trends, changes and variability in climatic variables is another indirect means of understanding potential future changes or variability at regional and local scales. The main objective of this paper is to review studies related to climatic change or variability and associated hydrologic changes at a regional scale and local scale, particularly those studies applicable to the Oil Sands Region (OSR) of Alberta. This paper identifies gaps in our current understanding of the hydrologic processes that may be affected by climate change; it discusses potential implications to developments in the OSR; and it explores mitigation opportunities including several that have already been implemented.

May 1, 2004