Search Documents

By M. Aushouri, S. H. Mansouri, N. Aminizadeh

A thermo-chemical model of the Peirce-Smith copper converter has been developed to predict the molten temperature. The primary assumption of the model was that all matte, slag and gaseous phases in the converter were in thermal and chemical equilibrium. In this model, the matte components were considered only as copper, iron and sulfur elements. In the slag making stage, all the reacted iron was converted to fayalite. The reaction rate of iron and oxygen in this stage was considered to be constant. The converter temperature was calculated by heat balance over time. The model was validated by a detailed comparison with measured industrial data. A good agreement was obtained. The converter temperature depends on process parameters such as oxygen efficiency and molten emissivity.

Jan 1, 2007

By Mory M. Ghomshei

"The cost of deep underground mine cooling depends on a number of geological, environmental and economic factors such as the temperature gradient in the mine, the outside air temperature, and the local price of energy. While geological factors, being static, can be controlled to some extent during the mine design, the environmental and economic factors dynamically change and therefore can only be controlled through a flexible mine ventilation system.With an average temperature gradient of 20–25°C/km, the virgin rock temperature at 2,000 m can reach 45–60°C. Conventional cooling at such depths could lead to exorbitantly high costs. In-mine geothermal heat pumps can considerably reduce the cost of cooling through energy communication with the centralized absorption chillers, which service the mine from the surface.It is shown that in-mine heat pump systems can be a viable option for reducing operating expenses and providing some degree of flexibility to cope with fluctuating energy costs. The price of Natural gas and electrify are the most important variables for optimizing the level of interaction between the surface and inmine cooling systems. Deep mine waters can be used to carry a portion of the mine heat to the surface, where the heat from mine can be used as a supplementary energy source for absorption chillers. As an extra benefit, the heat output of the chillers can be used for district heating and or greenhouse growing.The case of cooling deep levels of deep mines in Sudbury Canada (e.g. Creighton Mine) has been discussed. It is shown that an initial 1MW in-mine geothermal heat pump system can save significantly on the cost of cooling. Such a demonstration project will allow R&D on viability of larger similar systems to be incrementally added in the future.INTRODUCTIONThe amount of heat generated in deep and ultra-deep mines depend primarily on the regional temperature gradient and the thermal conductivity of mine rocks. The conductive heat flow is quantifiable and can be minimized or optimized in the process of mine design. Another important heat source can be related to underground equipment such as diesel machinery which often have low efficiencies (approximately 25–35%). This heat source can be controlled and reduced though improving efficiencies or using electrical equipment, which offer a much better efficiency (approximately 80–90%). Mine waters can also be a significant heat source (convectively bringing large amounts of heat into the mine workings)."

Jan 1, 2019

By Ron Light, Doug Applett

"HistoryThe Nanisivik mine began operation in October 1976 as the world's most northerly metal mine and the first permanent industrial project in the Canadian High Arctic. Located 700 km north of the Arctic Circle on Baffin Island's Strathcona Sound, exploration by Texasgulf Inc. between 1957 and 1970 had outlined the ore deposit. In 1974, Nanisivik Mines Ltd. was formed with Mineral Resources International, the Government of Canada, Metallgesellschaft and Billiton being shareholders, and Strathcona Mineral Services Ltd. providing project management. In 1996, Breakwater Resources purchased the mine from Alberta Energy Corporation Limited which had recently acquired the assets of then owners Conwest Exploration Ltd.Ore DepositThe main ore deposit is very flat, approximately 80 m in width and varying in thickness from 3 m to 16 m. The length of the deposit is approximately 3000 m with satellite zones located on the perimeter of the main zone. The economic mineralization is sphalerite with minor galena and silver. The sphalerite and galena are coarse grained and associated with pyrite as the main gangue component with minor inclusions pf dolomite and calcite within the deposit. The deposit being hosted in a permafi·ost environment creates a number of challenges. Dry drilling is employed in room and pillar production drilling. The permafrost aids in the stability of both the pillars and the back."

Jan 1, 2000

By Jason Palmer

"Water in mining is the commodity that has driven the mining industry for decades. Often used frivolously, modern economic and social pressures are forcing change to use less water and to improve the quality of water and effluents. Used in many processes, water is ultimately consumed in tailings disposal and technologies which can increase the recovery of water are constantly being developed. Filtration and thickening are often seen as competing technologies for water recovery however new cases are developing that show significant advantages can be achieved by combining the two technologies to develop the most effective solution. Supported by case studies this paper investigates the merits of each of the technologies and which strategies of combining the two produce the best outcomes.INTRODUCTIONMineral processing applications generally require water for the processing of ores, whether utilising physical or chemical methods. Water is first added in the milling stage and additional water added as required throughout the circuit. Water losses from the circuit are principally associated with the tailings stream. Optimised water recovery is necessary both because it is a scarce commodity and to minimise the environmental impact.Water recovery is usually accomplished through a sedimentation or filtration processes. Water can be removed from the tailings impoundment by evaporation but this does not improve the mine’s water consumption. The water recovery methodology also determines the water quality; increasing water recovery concentrates solutes in the process water and may create recirculating loads of fine solids."

Jan 1, 2016

By C. J. Hartley

"Scandium oxide can be recovered as a by-product from process streams in a number of chemical and metallurgical plants including TiO2 sulphate pigment, Ni/Co laterite, zirconium oxychloride and uranium operations. The feed materials available for processing can be either mid or end of process streams containing many species in solution. This paper describes the strategies available to limit coextraction of elements into scandium containing streams from TiO2 pigment production and the removal of these elements to deliver high purity scandium oxide.A critical part of process development is to work within the constraints of the main process in terms of introducing new unit processes and producing minimal additional process intermediates and residues. This requires flexibility in designing flowsheets and plants to find novel process routes that avoid production of intermediates and/or the introduction of reagents that can compromise the main process operations.Bloom Energy has developed novel solvent extraction processes for the extraction and refining of scandium oxide that minimise impacts on core process streams within TiO2 pigment plants. The additional unit processes are designed to have minimal contact with pigment plant process streams to produce a concentrate that is refined to nominal 3N purity scandium oxide in a simple, small scale commercial plant."

Jan 1, 2016

By Raymond S. Suglo

Increasing depths of mining coupled with the mechanization of most underground mining operations have led to growing complexities in the mine environments with the production of large amounts of gaseous and particulate contaminants. Over 100,000 lives have been lost due methane gas and dust explosions in coal mine workings in both the US and Canada since 1900 when the methane concentrations exceeded stipulated levels in some workings. There is therefore the need to constantly assess and evaluate the performance of the existing mine ventilation systems to maintain safe and acceptable mine environmental conditions in workings to meet the requirements of federal, state or provincial laws. This paper uses the results of continuous monitoring of methane concentrations conducted in selected development headings in coal mines in North America to assess the effectiveness of existing auxiliary ventilation systems in the control of methane gas concentrations in the headings. The results show that the average quantities of fresh air required to dilute, disperse and remove methane concentrations within set levels of one minute varied from 5.43 m3/s in Heading #11 (Condition 2) to 27.97 m3/s in Heading #10 (Condition 1) and this represented about 12 to 26% of the quantities required to dilute methane concentrations to safe levels within one minute under Condition 1 and 32 to 139% under Condition 2. The average dilution times in the headings studied were less than 8 minutes. The forcing efficiencies of the auxiliary systems in the headings studied ranged from poor to excellent implying that the auxiliary ventilation systems were capable of controlling the methane concentrations below statutory levels but may not be able to cope with large and unusual methane concentrations in the headings. This study is important to prevent methane gas and coal dust explosions in coal mines and thus avoid any loss of lives and property.

May 1, 2001

By R. Tervo, G. Ellie

"Automated information systems are being developed very rapidly in Europe. In France, Belgium and West Germany, more than 70% of the coal production is controlled by these installations. Information on both product ion and the mine environment is produced. For example, at one mine in France the system records the operating times of the compressors and of the refrigeration pumps, counts the number of coal cars passing the unloading point, and controls the principal conveyors and the loading /unloading of the storage bins. In addition, the ventilation air velocity, the methane content and the carbon monoxide content in the return air entry are recorded; an alarm is triggered and the current to the conveyors cut when the gas content exceeds a critical level. The recorded information is used at four levels: (1) for immediate action, (2) for daily reports, (3) for monthly reports and (4) for long-term studies. For example, when any conveyor is stopped for more than 10 minutes, the system controller immediately telephones to learn of the reason. At the end of a shift, the load factor of the conveyors is computed; then monthly an analysis of the causes of low load factors is made. The presentation describes in detail the system that has been installed in more than 20 mines in France."

Jan 1, 1973

By G. Wren

As base metal sulphide resources become increasingly challenging to process, producers seek alternative options to treat concentrates. This study considers the mineral, elemental, and leaching character of a West Australian nickel sulphide deposit (Cosmos Nickel Project). After a brief review of the published work bench top leach tests were conducted to examine the factors which impact the kinetics of nickel sulphide leaching such as particle size, temperature, acid strength and type, concentration of copper sulphate and sodium chloride, and oxygen partial pressure. The effect of sodium chloride was considered due to the common occurrence of hyper saline water at West Australian nickel sulphide mine sites. Ultrafine grinding to an 80% passing size of 10 µm resulted in high nickel leaching efficiency. Moreover, higher concentrations of acid, copper(II) and sodium chloride also gave higher nickel and cobalt leaching efficiencies but arsenic precipitated as FeAsO4. Under the most suitable conditions the extractions of nickel, cobalt and arsenic at 90oC after 6 hours were >95%, 90% and <5%, respectively. The comparison with results from high pressure operations indicates the possibility of using a hydrometallurgical flowsheet based on fine grinding and atmospheric pressure leaching and warrants further investigations.

Jan 1, 2014

By C. Jay Hodgson, P. J. MacGeehan, T. Sanders

"The orebodies of the Campbell and Dickenson mines are localized within an anomalously fissile and deformed zone that transects the eastern margin of a dominantly mafic volcanic complex close to its contact with a synchronously formed sedimentary basin containing clastic and chemical sedimentary rocks. The ore zones are mainly quartz-carbonate fissure veins and siliceous replacement zones formed during deformation and metamorphism, although there are some syn-volcanic exhalative ore zones in the mines. On a regional scale, the volcanic rocks have been affected by syn-volcanic spilitic alteration which has involved the leaching of Fe, Mg, Au and As from, and the addition of Na and variable amounts of Si to bleached zones enveloping primary permeable structures in the rocks. The leached constituents were deposited on the contemporaneous sea floor as iron-rich chemical sedimentary rocks. Although this alteration is not closely related, spatially, to the ore zones, it is characteristic of the general environment, and may serve to distinguish gold-prospective from gold-barren areas on a mining-camp scale.Closely associated spatially with gold deposits is a zone of feldspar-destructive alteration within which the volcanic rocks are characteristically feldspar-free, enriched in As, Au and to a variable degree in Si, and depleted in Na, Ca and to a variable degree in Mg, Fe and K. The alteration zone is also characterized by abundant, variably transposed, small quartz-dolomite to ferrodolomite veinlets formed during deformation and metamorphism, and includes, but extends outside of, the anomalously fissile zone hosting the orebodies. The alteration zone is interpreted to have formed syn-volcanically within the upper part of a major submarine hydrothermal discharge zone."

Jan 1, 1982

By Richard A. McIvor

"All mine shaft conveyances in Canada and most of the United States that are supported by a single hoist rope or attachment point and used for transporting persons are required by regulation to be equipped with safety catches and mechanisms. These safety mechanisms, commonly called safety dogs, are designed to stop and hold a free falling conveyance, with a full personnel load, in the event of a hoist rope or attachment component failure. The conveyance’s safety mechanism must be tested under dynamic conditions before it is used to transport personnel. This paper will discuss free-fall testing and it’s results on conveyance free-fall tests performed in the test tower at INCO Limited, Sudbury, Ontario.Topics covered will be free-fall tests on various wood types such as B.C. fir, Karri wood and Trusjoist MacMillan Limited Parallamwood (PSL), comparison of deceleration rates versus free-fall velocity and the influence of safety dog tooth design on deceleration rates."

Jan 1, 1996

By C. Hunt, J. Vivas, D. M. Allen

"In this paper we present the results of a combined remote sensing - numerical modelling study to improve our understanding of groundwater seepage in open pit and natural rock slopes, and to investigate the interaction between groundwater, in-situ stress conditions and brittle fracture. The location of seepage is a key element in the characterisation of rock slope stability in open pits and natural slopes; definition of the fracture network geometry and its inter-relationship with seepage, however, remains a challenge in engineering practice. Current techniques used to characterize groundwater seepage locations require direct access to the rock slope for a detailed and exhaustive investigation, and can be severely limited due to access and the limited coverage of the survey methods both with respect to the height and length of the sampled rock slope. Herein, we describe remote sensing methods, which allow the collection of structural and seepage information over a wide spatial area. Remote sensing techniques are shown to have the potential to provide additional insights into the orientation and general connectivity of fractures that may play a major role in the general stability of a rock slope. A preliminary methodology for the use of remote sensing in the characterization of seepage zones in a natural slope through the application of ground-based LiDAR and Infrared Thermography (IRT) is presented.One of the most challenging problems in rock slope engineering is the realistic simulation of fluid flow through fractured and deforming rock slopes. Deformation and the development of brittle fractures can cause significant local changes in the permeability and strength of the rock mass, potentially affecting rock slope performance. Understanding fluid flow through fractured and deforming rock slopes, especially in highly-stressed environments is of great importance for slope stability analysis. Changes in the interconnectivity of fractures during slope failure are an important, yet are relatively unstudied in rock slope engineering. We present the results of hydromechanical UDEC-Trigon rock slope models focussing on the potential role of brittle fracture in rock slope failure, its interaction with groundwater pressures, and the influence of the assumed in-situ stress ratio. Damage intensity parameters are used to characterize damage within different regions of a biplanar slope failure."

Jan 1, 2015

By Eddy Dénommé, Deni Villeneuve

"Niobec mine, a producer of pyrochlore concentrates since 1976, became a producer of ferroniobium in 1994 and achieved accreditation to the ISO 9002 standard in 1995. The goal of ISO 9002 is to ensure that the products supplied to clients regularly meet their specifications, through explicit work standards and procedures throughout the production process, from deposit appraisal to ferroniobium production.A key element of ISO 9002 implementation at Niobec consists of the quality control procedures applied to the raw materials: the ore fed to the mill and the pyrochlore concentrate fed to the reduction plant. These controls extend from exploration, deposit appraisal, mine planning and reserves estimation, mining, mineral processing and, finally, ferroniobium production. The implementation of ISO 9002 has allowed more efficient control of the quality of the final product sold to clients. It requires interactive team work, the role of the geologist being to relate all information pertaining to raw material and product quality to the geological framework of the deposits."

Jan 1, 1997

By A. R. Sorta, D. C. Sego

ABSTRACT The settling, shear strength, and index properties of oil sands fines-sand mixture tailings (FSMT) for a wide range of solids and fines content are investigated. Results indicate that the liquid limit of FSMT obeys a linear mixture law. The fines-water ratio (FWR) governs the permeability of composite tailings (CT) and CT with comparable geotechnical behaviour can be produced from the same initial FWR mixtures. A phosphogypsum (PG) dosage > 900 mg/kg does not improve the dewatering behaviour of CT. The undrained shear strength of FSMT at the liquid limit is approximately 2.4 kPa, but is dependent on fines content at the plastic limit.

Jan 1, 2013

By W. R. A. Graeser

"The Nordenham finishing mill is situated in the town of Nordenham, Fede1•al Republic of Germany, on the banks of the Weser River opposite the town of Bremerhaven, with access by water to the North Sea.The unfinished fibre, shipped j?•om Deception Bay during the sub-Arctic summer shipping season, is unloaded from bulk ocean carriers, stored and then processed throughout the year until the following shipping season. This paper describes the unloading and storage facilities,the finishing mill and the finished-fibre storage arrangement. Details of environmental and dust control practices and West German environmental standards are discussed. A resumé of fibre markets is included."

Jan 1, 1976

By E. B. Wilson

"Although the Operations Research technique of Reliability Theory has been applied with marked success in many fields, including the Apollo spaceship programs, the concept of reliability has not been generally adopted in mining and other heavy industries. Of course, reliability, or the probability that a system will be able to operate without a failure for a given interval of time, does not require the same emphasis in mining as in the aerospace industries. Nevertheless, certain aspects of Reliability Theory can be followed advantageously. For example, reliability calculations can determine the best time to overhaul and whether to retain stand-by units.The usefulness of the pseudo-operations research technique known as Replacement Theory is more readily re-cognized by the maintenance engineers in mining and other heavy industries. One of the least complex models enables the optimum Lifetime of an asset to be determined."

Jan 1, 1970

By J M. Gibbs

Craigmont Mines Limited mine 50,000 tons of ore and waste per day from the open pit at Merritt, British Columbia. An electric-powered "down-the-hole" drill, a diesel-powered rotary drill and two electric-powered rotary drills have been used. All primary drilling, as a result of cost and operating experience, is now performed with two electric-powered rotary drills. Trials with various loading techniques have increased the amount of AN-FO and decreased the amount of commercially prepared slurries used for primary blasting. Approximately 95 per cent of the primary blasting is accomplished with AN -FO, mixed at the hole. Introduction THE Craigmont mine is located near the village of Merritt, B.C., 240 miles northeast of Vancouver. The concentrator has been in production since September of 1961. Craigmont is a combined open-pit and underground operation. To date, slightly more than 95 per cent of the mill feed has been mined from the open pit. As underground development proceeds, the ore requirements from the open pit will decrease. The average milling rate from September, 1961, to April, 1964, was approximately 4,900 tons per day.

Jan 1, 1965

By Dean S. Rogers

"In February 1980, Dome Mines Limited announced a $50 million expansion program which would result in a 50% increase in mill capacity from the present 1,815 tonnes per day to an eventual production rate of 2, 720 tonnes per day in the year 1984. As an integral and necessary part of this planned expansion, a new vertical production shaft, No. 8 Shaft, would be sunk from surface to a depth of 1,645 metres.Throughout the seventy-year history of mining at the Dome, gold has been found in a number of different rock types and in association with a number of different structural settings. However, the key to successfully locating ore deposits lies in the recognition of the favourable environments in which they generally occur. First and foremost, the exercise of locating the No. 8 shaft became an exercise in geological deduction based on the projection of these favourable lithologic environments.In November 1980, after detailed engineering work was completed, the total cost of the project was estimated at $75.5 million 1980 dollars or $91 million dollars allowing for inflation over a four-year construction period. These estimates include the shaft, significant replacement and alterations to the milling process, and an upgrading of the plant."

Jan 1, 1982

By Donald Brisebois

The mining of high-grade, narrow vein deposits is an important field of activity in the precious metal mining sector. The principle factor that has undermined the profitability and effectiveness of mining such ore zones is the substantial dilution that occurs when blasting with explosives during extraction. In order to minimise dilution, the Thermal Fragmentation Mining Method enables the operator to extract a narrow mineralised corridor, 50 cm to 1 metre wide (according to the width of the vein), between two sub-level drifts. By inserting a strong burner powered by diesel fuel and compressed air into a pilot hole previously drilled directly into the vein, a thermal reaction is created, spalling the rock and enlarging the hole to 80 cm in diameter. The remaining ore between the thermal holes is broken loose using low powered explosives, leaving the waste walls intact. This patented method produces highly concentrated ore, resulting in 400% - 500% less dilution when compared to conventional mining methods. The mining method reduces the environmental affects of mining operations since much smaller quantities of rock are displaced, stockpiled, and treated using chemical agents. The fully mechanised equipment operated by a 2-person team (1 thermal fragmentation operator, 1 drilling operator) maximises the effectiveness of skilled personnel, and increases productivity and safety. The Thermal Fragmentation is currently employed in 3 mining operations in North America.

May 1, 2010

By X. Cao, A. Birur, R. R. Chromik, J. Cuddy, P. Wanjara, J. Gholipour Baradari, T. Shariff

In this study, 3.1 mm thick Ti-5553 (Ti-5Al-5V-5Mo-3Cr) butt joints were autogenously welded using a 4 kW continuous wave Nd:YAG laser. The effect of welding speed and defocusing distance on the weld quality was investigated in terms of the surface morphology, welding defects, microstructure and hardness. Welds with full penetration were achieved at a defocusing distance ranging from -1 mm to 0 mm and welding speeds from 2.25 to 6.0 m/min. Underfill and porosity were the two main defects most frequently observed but within the optimum process window these defects could be maintained to meet aerospace specification tolerances. The fusion zone (FZ) consisted entirely of retained beta with a refined dendritic morphology. Compared to the bimodal alpha (a) + beta (ß) microstructure of the base metal (BM), the dissolution of the a phase was observed in the heat affected zone (HAZ), which led to an 11 % decrease in hardness from the BM to the FZ. To determine the tensile properties of the welded samples, an automated 3D deformation measurement system was used to measure the local strain in the weld region. The yield strength (YS) and ultimate tensile strength (UTS) increased with increasing welding speed with a highest joint efficiency of 75 % being achieved, albeit with a concomitant reduction in the ductility.

Jan 1, 2010

By C. Joulian, A. G. Guézennec, A. Chmielarz, Y. Ménard, M. Hanke, P. d’Hugues

"The copper concentrate used in this study is produced by flotation of a black shale organic rich ore. This resource is a carbonate-rich, polymineral concentrate. In the last 5-6 years, ore characteristics changed and the concentrate grades degraded. This study evaluated bioleaching of the concentrate in stirred tank reactors as an alternative to the pyrometallurgical technology that is currently applied, and which may no longer be feasible in future given the concentrate chemistry.The first part of the study focused on testing non-traditional operating conditions during continuous bioleaching experiments: high solids concentration (> 20% solids), reduced agitation and aeration rates. For the same residence time, bioleaching performance at high solids loading (25%) was the same as that reached during previous bioleaching experiments at 15% solids. No mixing or microbial issues were encountered. The bacterial consortium used in the experiments demonstrated a high copper tolerance.The second part of the study was devoted to technology development for metal recovery from copper bearing solutions obtained during bioleaching experiments. Due to the high copper concentration of the leachate, solvent extraction prior to electrowinning was not necessary. After iron removal, high quality copper cathodes (morphology and composition) were obtained from the PLS by electrowinning."

Jan 1, 2014