Search Documents

By M. Fan, M. Mankosa, G. Luttrell

"Column and other non-conventional flotation approaches continue to provide benefits where conventional flotation processes have exhibited limited success. This is particularly evident with respect to flotation of ultrafine and coarse particles. Advancements in air sparging technology have provided the ability to produce finer bubbles than previously possible. The generation of finer bubbles coupled with the froth washing capabilities of a flotation column has demonstrated improvements in ultrafine particle recovery while simultaneously producing a high-grade float product. On the other side of the spectrum, the use of these sparging technologies while applying flotation fundamentals to a fluidized-bed reactor has increased the maximum floatable particle size up to and in excess of 3 mm. Benefits of higher recoveries and reduced reagent consumption have resulted from the use of these technologies. An additional benefit includes a reduction in plant grinding requirements. As such, this paper describes the application of Cavitation-Tube sparger technology and fluidized-bed flotation (HydroFloat). A review of data from industrial and pilot-scale applications is also provided.INTRODUCTIONConventional (mechanical) froth flotation is considered the workhorse of the minerals processing industry. This low-cost process makes it possible to selectively recover minerals by exploiting the difference in surface characteristics (e.g., wettability) of the valuable component and the waste material. Unfortunately, the upper particle size limit for flotation rarely exceeds 0.600 mm, and is typically maintained at less than 0.300 mm for most industrial applications. For many commercial base metal plants, the particle size range for optimum recovery is typically between 0.01 and 0.1 mm (Lynch et al., 1981). This finding is not novel. In fact, the effect of particle size on flotation recovery was studied as early as 1931 by Gaudin et al. who showed that coarse (+0.250 mm) and extremely fine particles (-0.010 mm) are more difficult to recover than particles of an intermediate size. The loss of recovery is due to inherent limitations associated with the flotation process, including bubble-particle adhesion and collision, detachment, buoyancy, and transport."

Jan 1, 2010

By Mike Ounpuu

"Locked cycle testing has become more common practice in the last 10 years. Reasons vary from a desire to avoid pilot plant testing, demand for more variability testing within deposits, and perhaps most importantly, a request from the financial institutions who invariably finance many of the projects. Surprisingly, many people don’t understand locked cycle testing, analysis and balancing. This paper provides a brief overview of locked cycle testing, and then progresses into a more detailed discussion on the analysis and balancing of locked cycle test data. The paper endeavors to educate CMP personnel on how to determine if the test was good and if a reasonable metallurgical projection was made. The paper uses case studies to illustrate the key points.INTRODUCTIONA locked cycle test is a repetitive batch used to simulate a continuous circuit. The basic procedure has a complete batch test performed in the first cycle which is then followed by similar batch tests which have “intermediate” material from the previous cycle added to the appropriate location in the current cycle. These batch tests, or cycles, are continued in this iterative manner for an arbitrary number of cycles. The final products from each cycle, i.e. final concentrate and final tailings, are filtered and thus removed from further processing. At the end of the test, all the products, final and intermediate, are dried, weighed and subjected to chemical analysis. The test is balanced and a metallurgical projection is made.This description can be found in many of our classical textbooks for the mineral engineer 1, 2, 3,4. Unfortunately, none of these textbooks provide any discussion beyond the basic procedure. Often, they provide comments such as in Taggart’ where he states; “It is questionable whether in any case it approximates mill results any more closely than the standard batch test”. It is truly surprising that our classic textbooks promote that locked cycle tests are more art than science, and suggest that they can be of dubious value. None of the textbooks provide meaningful insight or discussion in how to assess:"

Jan 1, 2001

By M. Mononen, J. Huuskonen, M. Vauhkonen, J. Kourunen, A. Lehikoinen

"A new approach to measure process conditions in flotation cells is presented. Real scale flotation cells in a Zinc circuit are imaged using Outotec LevelSense sensors based on electrical resistance tomography. The latest results from long period plant tests show that the sensors together with FrothControl analysis give new information that correlates well with other process parameters. The sensors can compensate for electrical contact contamination using an automatic calibration technique and they are basically maintenance free. The results indicate that using the LevelSense sensors and FrothControl solution, the process control and optimization can be done automatically, stabilizing and improving the metallurgical performance of the flotation process.INTRODUCTIONThe froth flotation process is widely used in mineral industry for the separation of minerals from low-grade ore slurry. Different property parameters of froth and slurry could be measured to monitor and control the flotation process: air bubble size distribution, flow dynamics, thickness of the froth bed, amount of solids in the froth, etc. Some techniques already exist that can be utilized in studying these important parameters on-line. Examples of the techniques are the high-speed video imaging, simple conductivity probes, ultrasound techniques, floats and pressure transducers (Maldonado et al., 2008). These techniques, however, often suffer from some limitations. For example, the video imaging only gives information from the surface of the froth, simple conductivity probes suffer from contamination and the floats may get stuck and therefore do not give reliable signal for process control and optimization."

Jan 1, 2013

By A. J. Williams

"Conventional base metal milling practice normally consists of crushing, grinding and cyclone classification followed by flotation. It is the authors' belief that the commencement of flotation after cyclone classification leads to inferior metallurgical results and that implementation of flotation of grinding mill discharges can result in increased recovery due to reduced overgrinding, reduced activation of contaminating minerals and improved dewatering circuit results due to the production of coarser concentrates.The concept of recovering minerals from the discharge of grinding mills is not new! Gold concentrators have utilized jigs and flotation cells while iron ore plants have employed magnetic separators to recover gold and magnetite respectively from the discharge of grinding mills. More recently, a Reichert cone has been used to recover sulphide and oxide base metal minerals from screened rod mill discharge. 1To the authors' knowledge, the first application of flotation of base metal minerals from the discharge of a production plant grinding mill was at the Lake Dufault concentrator of Corpor'1tion Falcon bridge Copper. Located 10 miles north of Noranda, Quebec the Lake Dufault concentrator commenced operations in August, 1964.The installation of flot11tion cells in the Lake Dufault grinding circuit proved so successful that an identical system was installed in the Manibridge concentrator of Falconbridge Nickel Mines Limited. Located 90 miles southwest of Thompson, Manitoba the Mamibridge concentrator commenced operations in June, 1971 and due to exhaustion of economic ore reserves discontinued production in May 1977."

Jan 1, 1984

By John A. Herbst, Xiangjun Qiu

"Prediction of wear on a microscale level in mineral processing equipment turns out to be a challenging undertaking. This is particularly true for cases in which the objective is to use such predictions for wear parts design. The key to obtaining such predictions has turned out to be the use of physics based models along with phenomenological constitutive equations. In this paper, two components of the HFS tool set, one for particles (DEM) and one for slurry (MPF), are used for modeling. These tools are applied to the simulation of wear of SAG/AG shell lifters/plates and wear in slurry pumps. In each case wear predictions are validated with plant measurements.INTRODUCTIONHigh Fidelity Simulation (HFS) has emerged as an important tool set for mineral processing plant equipment design and optimization (Herbst and Potapov, 2003; Herbst and Nordell, 2002; Herbst and Lichter, 2006). This tool set consists of Discrete Element Modeling (DEM) of particle motion, Multi-Phase Flow (MPF) for liquid motion, discrete grain breakage (DGB) for particle fragmentation and discrete grain liberation (DGL) for mineral liberation (Campbell, Potapov and Tsuji, 1997; Ferzinger and Peric, 1997; Potapov and Campbell, 1996; Herbst and Potapov, 2005).Three sample snapshots of basic HFS illustrating the use of each of the various types of mineral processing equipment are shown below.Figure 1 shows a snapshot of a DEM simulation of ball charge motion in a commercial scale Vertimill. DEM simulation involves simultaneous solution of Newton’s Laws of Motion for 400,000 balls."

Jan 1, 2007

By M. K. Mishra, U. M. R. Karanam

Relative to slender pillars, larger size pillars exhibit improved strata control. Fly ash, though traditionally treated as a waste product, is emerging as an alternate engineering material. This paper deals with the development of a strong fly ash composite material with additives. The geotechnical properties of this fly ash composite were determined and used to trap model core pillars, which resemble squat pillars. The trapped samples were tested under uni-axial loading in the laboratory and the results showed higher load-bearing capacity of the model core pillars. The reinforced fly ash composites provide lateral confinement and exhibit improved post- failure behaviour of the model cores.

Jan 1, 2008

By D. F. Cooper, J. G. Paterson, K. H. Pang

"Effective control of metallurgy by manual adjustment of cell levels is common flotation practice. With an on-stream XRF analyzer interfaced to a process control computer it is possible to program the computer to carry out this function automatically. This paper describes the development and implementation of closed loop control of the concentrate and tailing grades at the Clarabelle Mill of the International Nickel Company of Canada, Limited, The XRF analyzer was used as the sensor, cell level as the control and the computer as the controller.IntroductionThe International Nickel Company of Canada, Limited recently brought on-stream Clarabelle Mill having a rated capacity of 35,000 tons per day. The plant was required to increase milling capacity in the Sudbury area by 9,000 tons per day and to improve milling efficiencies by replacing the obsolete crushing and grinding equipment at the Copper Cliff Mill. This represents the fourth mill built since 1959 and incorporates the latest thinking in a continuing evolution of instrumentation and control concepts. Table 1 illustrates control progress at Inco since 1959.In 1967 Frood-Stobie Mill came on-stream incorporating a central control room, an on-stream analyzer, a data gathering computer, and a significant change in instrumentation from direct-contacted pneumatic to miniature electronic. The computer successfully controls the analyzer but has very limited process control capability. Based on this experience a process control computer system was installed at Clarabelle Mill with the objective of carrying out extensive supervisory control and a limited amount of direct digital control."

Jan 1, 1973

By Sanjeeva Latchireddi

"Deteriorating ore grade and high demand of metals has tremendously influenced the unit capacity of SAG mills. Pebble circuits have been added to the existing SAG circuits to increase their unit capacity. To make the pebble circuits justifiable, the grate openings are increased almost to 4.5 inches to draw large quantity of pebbles. The inherent transportation problems associated with SAG mills in closed circuit with pebble fraction are more complicated than the single stage SAG mill operation, because the coarse pebbles behave significantly different to that of slurry in pulp lifters. In addition, operation of mills at higher speed, to take advantage of precise design of high release angled shell lifters significantly reduces the discharge efficiency of the conventional pulp dischargers. The presence of a sizable quantity of pebbles in the pulp lifter limits the space available and reduces the flow gradient through the grate thus increases the load inside the mill and hence the mill power-draw. This paper analyses all the problems associated in discharge of slurry and pebbles in SAG mills with pebble circuits. The Outokumpu patented Turbo Pulp Lifter (TPLTM) aims at eliminating the inherent material transport problems to ensure good grinding conditions. Recent installation of TPLTM in a 26-ft SAG mill has proven these claims by reducing the specific power consumption while increasing the mill capacity.INTRODUCTIONThe conventional wisdom is to look at the semi-autogenous grinding (SAG) mill as just another grinding mill in which ball charge, mill filling, and mill speed are varied to attain maximum throughput. Liner design for the SAG was also approached more from a wear perspective rather than a metallurgical and hydraulic-flow perspective. The extensive research work carried out by Latchireddi and Morrell (1997,2003a and 2003b) has demonstrated to think of the SAG as more of a pump in which the grates and pulp discharger end (“impeller”) were designed to efficiently discharge the product sized particles smaller than the grate size with minimal recirculation out of the mill.The rock load in the mill is essentially depends on ore characteristics and the discharge rate of broken particles. The discharge rate of the product material depends on how efficiently the discharge pump (grate and pulp lifters) is operating. Similar to the impeller design affecting the pump capacity, the pulp lifter design affects the discharge capacity (or mill throughput) of the SAG/AG grinding mills. The general arrangement of AG/SAG mills discharge system is shown in Figure 1."

Jan 1, 2007

By G. Herget

"A brief visit to European longwall mining operations in potash showed that retreating longwall mining provides a very attractive alternative to room-and pillar mining, especially in areas with bad roof, narrow seams and areas with high ground pressures. Mines de Potasse d'Alsace, France converted all potash operations to longwall mining in 1980. Recovery rates per panel vary between 75o/~ to 85% which compares very favourably with Saskatchewan values. Ground pressure in Saskatchewan are comparable to those of some of the deposits in Europe, but the presence of water in the hanging wall of Saskatchewan orebodies has to be given serious consideration. However, given the mining experience in Saskatchewan and the improved technology f or laboratory and field investigations, a review of present mining practice in Saskatchewan is desirable. IntroductionLongwall mining is practiced widely in coal mining and allows complete mechanization. It is applicable at great mining depth, in thin seams, weak roof and has been applied recently even to coal bed s dipping more than 65 degrees. Ideally this system allows complete extraction of an orebody. However, with high mechanization and emphasis on obtaining high outputs per man shift, extraction ratios rarely reach more than 80010 per panel.France, Spain and the U.S.S.R. have had longwall operations in potash for some time and a brief description is given below. Two of the operations were visited and the Russian operation is described based on German literature"

Jan 1, 1986

By Raymond J. Pichette

"Aeromagnetic data can be useful in helping to delineate structures and rock types in gold exploration. Magnetic anomalies associated with Archean volcanic belts in northeastern Ontario can be quickly and effectively analyzed in profile form with the use of model curves. The model curves help to locate contacts between strata. They also help to estimate the magnetite content of the rocks and their depth beneath overburden.An aeromagnetic map of part of Catharine Township, Ontario has been analyzed with the aid of model curves. Several magnetic rock types, potential fault zones and areas of relatively thick overburden were delineated.IntroductionIn any exploration program, a good understanding of the stratigraphy, rock types and structure enhances the possibility of success. For example, environments which host gold deposits in the Abitibi Volcanic Belt may be characterized as follows (Jensen, 1980; Pyke, 1980):(I) They have major faults, especially as tectonic boundaries between volcanic piles which include mafic and ultramafic rocks and clastic sedimentary rocks or gneisses.(2) They have subvolcanic felsic intrusions.(3) They have extensive carbonitization, with or without carbonate and sulphide-facies iron formation.In all cases, delineation of structure and rock type should be a major objective in exploration. The analysis of magnetic data can be a useful tool in this task. This paper is presented with the purpose of describing the application of the magnetic method to gold exploration in Archean volcanic terrains.Magnetic AnalysisTotal-intensity magnetic contour maps can be used to discriminate rock units according to differences in magnetization. However, because of smoothing of texture resulting from the compilation procedure and the fact that survey lines are widely spaced, contours should not be directly used for quantitative analysis. A much more definitive means of magnetic analysis is provided by the use of the original profile or chart recordings. Model curves provide a basis for analyzing these profiles both accurately and rapidly."

Jan 1, 1982

By Donald Leroux, Ralph Dahlke, Dave Scott, Finch. James A., Cesar O. Gomez

"The efficiency of the flotation process depends on how effectively air is dispersed into small bubbles. Bubble surface area flux - the surface area of bubbles per unit time per unit cross-section area of a cell - is emerging as the parameter to characterize gas dispersion. One of the approaches proposed to measure bubble surface area flux in industrial cells is based on the measurement of two variables: gas velocity and gas holdup, using separate sensors. Plant testing of the gas velocity sensor gave evidence of a series of operational problems which may be necessary to correct before attempting to characterize gas dispersion. Problems such as uneven air distribution within a cell and along a bank, faulty air and slurry valves detected during attempts to redistribute air, and poor control of pulp level and gas flow became evident. Detection of these problems from gas velocity measurements is illustrated.INTRODUCTIONBubble surface area flux is considered a key variable in the optimization of flotation circuit performance (Gorain et al., 1997; 1998). The Mineral Processing Group at McGill University has devised and developed a method for estimating bubble surface area flux in industrial flotation cells (Finch et al., 1999). The method is based on measuring gas holdup and superficial gas velocity using two separate sensors and applying drift flux analysis to estimate bubble size (Dobby et al., 1988; Banisi and Finch, 1994). With bubble size and superficial gas velocity known bubble surface area flux can be calculated.This method was selected by Noranda to characterize gas dispersion in cells as part of a program to model and optimize flotation circuit performance. However, initial testing at Brunswick Mine with the gas velocity sensor provided some unexpected results indicating operational problems and equipment malfunctions that needed to be addressed before systematic measurement of gas dispersion could be initiated.The subject of this communication is to illustrate the detection of these problems from gas velocity measurements. The line 3 Zn Cleaner circuit comprising four stages of Denver DR cells was the main subject of analysis, including the effect of correcting these problems on the metallurgical performance of the Zn 3rd cleaner bank of ten DRl 00 cells."

Jan 1, 2001

By M. Tarvainen, J. Kallioinen

"Depressed metal prices coupled with increasing production costs have presented a great challenge for operators to control and reduce the costs of production to maintain profitability. Depleting ore reserves, added to the above has forced Outokumpu to take a hard look at its operations, to develop new methods to profitably extend the life of its mines. One of the areas investigated and approved for further development has been the use of larger and more energy efficient equipment. As a result, large flotation machines were developed and today 38 and 60m3 flotation machines are in use.Secondly, ore preconcentration has been developed to avoid processing the part of the ore that has little or no mineral values.Another quite recent development and the topic of this paper, has been the use of coarse flotation before conventional flotation. The main idea is that part of the valuable mineral is separated as early as practical by floating it with specially designed flotation equipment, installed in the grinding classification circuit. The new flotation cell is specially designed for this application and differs from the conventional cells in the tank design, feed arrangement and modified mechanisms in some cases."

Jan 1, 1984

By Bill Shand

"Placer Dome - Campbell Mine is a gold mine located at Balmertown in the Red Lake District of North Western Ontario. During the last 50 years, the mine has produced over ten million ounces of gold.A change in ball mill grinding media was made in August 1998 from 1.5” diameter forged balls to 1.5” diameter, 18% chrome balls. This was done to reduce grinding media consumption and to potentially help flotation performance.A marked ball test done in September-October 1999 showed that, of the alloys tested, 18% chrome was the optimum for the ore at Campbell Mine. The test showed that consumption of chrome balls should be 3 times less than forged balls.In December 1999, the ball size was increased from 1.5” to 2” in an effort to reduce the amount of oversize rock discharging from the ball mill. This change in size was successful.Grinding media consumption for the ball mill decreased 73% from 1.20 kg/tonne before the use of chrome balls to 0.327 kg/tonne after the use of chrome balls. This clearly indicates that, for the ore at Campbell Mine, there is significant savings in grinding media by using chrome.Grinding ball costs were reduced by 59% from $O.88/tonne of ore milled to $0.36/tonne of ore milled representing a saving of $298,000 per year. This also clearly indicates that using chrome balls is a benefit at Campbell Mine.Test work to show that chrome grinding media is beneficial to flotation has been inconclusive so far but is still ongoing.No tests have been done to see if there would be a benefit with an even higher chrome percentage in the grinding media. Test work in this area is also planned for the future"

Jan 1, 2001

By Christine Hansen

?Kiss my Asteroid? Unofficial Title Human life is tied to minerals It?s worth noting that: The living human body consumes minerals. The minerals we take in multivitamins show the close linkage between human beings and mineral resources. Unlike tourism or specialized manufacturing, a human being could not live without mineral consumption. Minerals and their consumption is a tangible part of human life.

May 1, 2013

By C. J. Allen, L. Battiston

"Introduction It has long been recognized by the hot-dip galvanizing industry that the characteristics of the galvanized coating can be influenced significantly by steel and pro cessing variables. Probably the variable of most concern to galvan izers today is steel chemistry. More specifically, the problem is the excessive reactivity of continuously-cast, silicon-bearing steels. In the past, structural steels processed by general galvanizers were in the low-to-medium ca rbon category and contained silicon at either low impurity levels (as with rimmed steels), or less than approximately 0.10% (as with semi-killed steels). The structures of the coatings produced on such steels are characterized by dense, compact layers of delta and zeta iron-zinc alloy phases and a distinct outer layer of eta zinc, which usually imparts a bright shiny appearance to the coating. The presence of silicon in steel, above the so-called semi-killed levels, is known to cause marked stru ctural changes in galvanized coatings. Such coatings are characterized by a relatively thin delta layer, a thick , coarse zeta layer and frequently an absence of the eta layer. The eta phase, comprising zinc which is carried out of the bath during withdrawal of the work, can be consumed by the continuation of the coating reactions until its temperature drops to the solidification point. This results in a dull grey and often mottled surface instead of the usually bright metallic appearance. These galvanized coatings are usually much thicker than coating specifications requ ire and they are usually more brittle and have poor adhesion to the steel. In service, these coatings tend to develop a rust-like discolouration. With the wider use of continuous casting by the steel producers and the associated additions of silicon in this process, the problem is becoming more important and receiving greater attention from the galvanizing industry ."

Jan 1, 1987

By H. R. Banks

IF you have ever travelled in the valley lying between the Selkirks and the Rockies in the East Koorenay district, you will have noted that the former mountains are rounded and massive, while the serrated peaks of the latter, fingering into the sky, bring an entirely different. picture. These two mountain ranges, with the comparatively level valley between, serve splendidly to introduce the subject for discussion. It is rather strange that, despite the fact that wear is undoubredly the greatest force with which human ingenuity bas to contend, it has come in for very little study from the stand point of pure science. Empiricism has been the sole ally in the fight for improvement! That we may have a clear understanding as to what we mean by wear, I would include in the term the breaking dawn of ail solid matter, from the natural wearing dawn of the mountains previously mentioned, to the hale in the mill pipe-line, which forces one to shut-down-usually at some un-earthly hour-to carry out a repair. It seems a far cry from mountains to mill launders or pipe-lines, but, magnified sufficiently, most of the materials with which we have to deal would show surfaces not unlike those we see around us. The progressive steps of wear, or ?erosion' as our geological friends would prefer to term it, are exemplified in the two ranges of mountains and the valley between. True, the wearing dawn by natural forces is a slow process. The aeons which have passed since first these mountains were formed seem endless. The natural forces pitted against them seem puny in the light of the interminable rime that has been needed to effect the changes. But here, as in the case of the materials with which we are dealing day by day, the combination of many forces ultimately brings about that condition which we describe as 'worn out'. In the case of the mountains, it is when they are finally levelled into plains, and in the case of equipment which we use, it is when that equipment will no longer serve its purpose.

Jan 1, 1943

By Richard Peaker, Jens Lichter, Alexander V. Potapov

"The recent combination of Computational Fluid Dynamics (CFD) and Discrete Element Modeling (DEM) can provide considerable insight into the performance of flotation cells. One area of interest from a fundamental equipment design perspective has been the influence of flotation cell size and the inflow rate on the metallurgical performance of the cell. One of the specific design objectives when increasing the size of flotation cells, or increasing the feed flow to the flotation cell, is to ensure that the feed stream flowing into the cell does not have an opportunity to bypass the mechanism.This paper describes the initial modeling efforts to quantify the inter-relationship of cell size, inflow rates, and feed and discharge box placement, on the retention time distribution of solids in the flotation cell, and the fraction of particles that bypass the mechanism on a size by size basis.INTRODUCTIONThe great majority of newly installed cells in mineral processing plants world-wide are of the cylindrical tank design and this tank shape offers a number of hydraulic advantages over the older style of square cells. Cylindrical cells give symmetrical flow patterns and by careful design of the mechanism and tank internals, the flow patterns generated can concentrate the more intense mixing in the lower portion of the cell to promote good solids suspension and particlebubble contact. Simultaneously, cylindrical tank design gives a more quiescent upper zone for particle-bubble transport into the froth zone. These symmetrical flow patterns are naturally disturbed in normal operation by the slurry inflow and outflow from the individual cells. The challenge for flotation cell designers is to determine the magnitude of these flow disturbances, and to assess whether or when the inflow and outflow rates have a sufficient impact on the hydraulic flow patterns so as to potentially affect the metallurgical performance of the flotation cell."

Jan 1, 2007

By Colin Hardie, Simon Pelletier, Rakan Rhabani, Guy Comeau

"In order to improve the nickel concentrate thickener operation at Raglan Mine, two pulp deaeration cyclones were installed. These units obtained from Outotec Pty Ltd, also called the FrothBuster®, have been in continuous operation since mid-October 2006. The primary objective of the de-aeration cyclones is to lower the solids content in the thickener overflow by de-aerating the concentrate pulp before it enters the concentrate thickener. This dearated slurry should help decrease the nickel particle losses that report to the thickener overflow because of the flotation effect within the thickener.Optimizing the de-aeration cyclones has been a slow and ongoing process, however, initial testing is encouraging. The latest test results indicate a 50 % reduction (0.070 to 0.035 % solids) in nickel losses to the concentrate thickener overflow resulting in an additional $350,000 in annual revenues.This paper will present an overview of installing the de-aeration cyclones within a limited space, as well as the preliminary commissioning and testing challenges. This paper will also discuss the most recent concentrate thickener operating results since the de-aeration units were installed.INTRODUCTIONThe Xstrata Nickel Raglan Concentrator, located at the northern limit of Quebec’s Nunavik Region has been in production since 1997. In early 2002, the concentrator implemented the Zero Process Water Discharge (ZPWD) project to recycle the process water to decrease fresh water consumption and reduce discharges to the environment. Due to this initiative, the chemistry of the process water changed significantly resulting in flotation concentrate streams, which were very frothy and difficult to manage. This phenomenon has resulted in operational challenges in many areas of the concentrator including slurry pumping, flow measurement and concentrate thickening.In October 2005, the Raglan Mine underwent a conversion from an AG mill to a SAG mill operation in order to increase throughput and to optimize key process areas. As part of this project, the first two North American pulp de-aeration (FrothBuster®) units from Outotec were installed to improve the operation of the concentrate thickener. The primary objective of the deaeration technology was to lower the solids content in the thickener overflow by de-aerating the concentrate thickener feed pulp. This in turn was to reduce the froth, which accumulates on the thickener surface, and more importantly reduce valuable nickel losses to the thickener overflow because of the flotation effect within the thickener."

Jan 1, 2008

By Dave Bulled, Jim Thompson, Tim Leriche, Mark Blake, Troy Wilkie

"A commitment to a core testing, plant modeling and reconciling technique has shown substantial economic benefits to IOC in terms of accurate production forecasting, smoother operation of the mill, improved expectations of throughput and co-operation across production departments from geology, planning, mining, and processing, to shipping of concentrate to market.This paper describes a successful seven year program of forecasting throughput of the autogenous milling circuit at the Carol Lake concentrator of IOC. Work started with audits of the grinding circuit in 2001 and benchmarking of the data collected from samples of mill feed and plant operation to the CEET mill design and throughput forecasting model.Initially 390 drill core samples were tested for SAG Power Index (SPI) to measure the energy required in milling, and the data distributed using a geostatistical technique across the two operating pits, so that hardness was estimated in each of the 40,000 blocks (or 1500 million tons) of potential ore. In 2004 a forecast of energy requirement, i.e. forecast of throughput for a given power availability at the mill, was produced for each ore block using the CEET model and used for mine planning to smooth plant throughput. The forecast for blocks mined on a monthly basis was reconciled with plant results over the next 2 years and minor changes made to the CEET model. The forecasting exercise was repeated in 2006 and in 2008 with the latest model based on the testing of almost 1300 samples of drill core at closer spacing.INTRODUCTIONThe contracting of sales to clients and the timely supply of products to meet those contracts is a cornerstone of good business practice. Ensuring the correct scheduling of production is a major concern of mining companies where the supply and qualities of the raw material is uncertain and production facilities are not flexible. This is particularly challenging when the product is of high volume and produced far from the customer, such as iron ore.Apart from the metal content of the ore being mined, the greatest impact on production scheduling is the throughput of the comminution section of the extraction plant; most notably when size reduction is achieved by autogenous grinding. The response of the mills to variability in the hardness of the ore can change throughput by as much as 50% from day to day at some plants."

Jan 1, 2009

By Peter Radziszewski

"Comminition process costs, which typically represent an important contribution to mining operating costs, can themselves be divided roughly between energy and liner /charge wear. As such, developing the ability of predicting mill wear will allow a more accurate estimation of wear costs and therefore their control. In this paper and based on the possibility of estimating energy dissipated in impact and abrasion by using a discrete element charge motion model for mill charge motion simulation, media wear will be investigated principally as a function of three wear mechanisms : impact, abrasion and corrosion. Experimental results will be used to identify a total media wear model. Model results will be compared with real mill data from three operating Australian mines. These preliminary results show for the cases tested that the overall average error, as compared with the observed cases, is 0 % with a standard deviation of 66.1 %. Results from the Bond abrasion index tests, for the same cases investigated, give an overall error of 73 % and a standard deviation of 192.5 %. Further work is in progress to improve test procedure, validity and confidence.INTRODUCTIONComminition process costs, which typically represent an important contribution to mining operating costs, can themselves be divided roughly between energy and line / charge wear. In Greenfield situations where the estimation of operating costs is critical in determining project feasibility, the level of confidence in such estimates becomes quite important. With regards to media wear, the Bond abrasion test currently serves as the standard media wear prediction device. However, as shown [l, 21 test results once compared with actual wear rates can vary greatly. Figure 1 shows test results as compared with 15 cases. Average error over this data is 73 % with a standard deviation of 192.5 %. As such, developing the ability of more accurately predicting mill wear will allow greater confidence in wear cost estimation and therefore their control."

Jan 1, 2001