Search Documents

WMC Resources Ltd has been involved the development and trialling of an automated load haul dump vehicle system since 1997. This paper describes the introduction of the system into the Olympic Dam Operation and its performance compared with existing manual loaders. In certain situations the autotram loader will outperform the manual operation, particularly on the longer distances. There were no personnel injuries associated with the operation of the system during the testing period.

Jan 1, 2005

The influence of pulp potential on the flotation behaviour of sulphide minerals in laboratory batch flotation tests is discussed in terms of self-induced flota- tion, collector-induced flotation, and depression.' Assuming that the pulp poten- tial is controlled by the same factors that determine the genuine redox poten- tial, an attempt is made to interpret the experimental results in terms of potential-dependent reactions based on bulk thermodynamic data. Self-induced flotation is displayed by many sulphides in moderately oxidizing solutions but not in reducing solutions. The available evidence suggests that the hydrophobic entity could be sulphur produced by superficial oxidation of the mineral but this has not been established beyond dispute. In general, flotation is observed near the potentials at which sul- phur would be expected to form and the minerals which produce sulphur seem to float the most strongly. Collector-induced flotation is most conveniently studied on minerals which have only slight self-induced floatab- ility. The mineral-collector interaction is potential-dependent hence flotation is generally only observed in limited ranges of potentials. While the general form of the floatability-potential relationship is similar to that predicted from thermody- namic data close correspondence between predicted and experimental results is not always observed.

Jan 1, 1984

By Houlihan RN, Landau J

A reciprocating plate column is described in which two sets of perforated plates are mounted alternately on two shafts and are reciprocated with a phase difference of 1800 between them. It is shown that such a column is mechanically superior to the previously proposed types: under practical operating conditions the pressure fluctuations at the base of the column are only a small fraction of the static head. Furthermore, mass transfer experiments with the system tributyl phosphate in kerosene- acid aqueous solutions of uranyl nitrate show that both high specific throughputs and reason- ably good efficiencies can be attained in this type of column. A comparison with the more conventional extraction equipment (mixer -settlers, pulsed columns) on the basis of residence time per equilibrium stage indicates the potential of reciprocating plate columns in hydrometallurg- ical application, especially in which the requirements of separation efficiency are modest while the scale of operation is large.

Jan 1, 1975

By Vassiliev P

Cut-off optimisation, based on the work of Lane (1988), can be used to maximise the NPV (Net Present Value) of a mine by the judicious manipulation of cut-offs and the use of stockpiles. Apart from maximising NPV, cut-off optimisation will ver

Jan 1, 1998

By Perry JH, King RL

The Bureau of Mines in cooperation with Kaiser Steel Corporation conducted two methane drainage studies in an advancing section of the Sunnyside No. I Mine where production was being severely hampered by methane emissions. A total of six horizontal aoreholes were completed during the studies to an average length of 291 meters. Total gas production from the boreholes as of December 1981 has exceeded 6,088,800 m3. Methane emissions into the section were reduced by 40 pct as a result of the first drainage system. The second drainage system is currently producing 11,328 m3/day from four Doreholes. Mining of the section and cementing of the horizontal horeholes is expected to begin within 2 Years.

Jan 1, 1982

The techniques originally developed to process digital images of Mars, later gained widespread acceptance when applied to Landsat data: they are now making a significant impact in fields of geology outside remote sensing. The three ingredients of success are seen to be firstly, the perceptual attributes of image displays and the use of colour; secondly, the absolute ability to register data from a variety of sources; and thirdly, the speed of specialist "interactive" digital image display systems. The future lies in further exploiting these attributes through a Geographic Information Systems (GIS) approach to data handling, integration and display.

Jan 1, 1986

By Gray J, Krouse HR, Changkakoti A, Kwak TAP

The Dachang tin field with more than one hundred million tonnes of ore at 1% tin and 3% Zn is one of the largest tin fields in the world. It comprises five carbonate replacement tin deposits, of which the Changpo deposit containing about 80 million tonnes of ore at about 1% tin is the largest deposit. The deposit, hosted by middle Devonian limestone, argillaceous limestone and black shale, is genetically related to the Longxianggei granite.The oxygen, hydrogen and carbon isotope data of minerals, rocks and fluids suggest a magmatic fluid which evolved during the crystallization of the Longxianggei granite. Mass balance calculations show that the depletions observed in 180 and 13C values of calcites from the ore bodies to the country rocks were due to continous isotopic exchange reactions between the magmatic fluid and the marine limestones at different W/R ratios and between 300 and 600¦C.

Jan 1, 1990

By Fraser CJ

Stability control plays a prominent part in the planning and execution of coal winning in the deep open cuts in the Latrobe Valley operated by the State Electricity Commission of Victoria (SECV). Different stability mechanisms affect the individual overburden and coal faces. These are the classical rotational slip in overburden and the three-dimensional tetra- hedral wedge or planar block slip in the coal faces. The stability of the overall batters is affected by the so-called "block sliding" mechanism, which is unique in Australian open cuts. The basal stability of the open cuts is affected by pressure from water in confined aquifers underlying the coal being excavated. This paper describes each of these mechanisms and the current monitoring and con- trol techniques practised by the SECV.

Jan 1, 1982

By Lockyer PC, Reed MR Bartlett PM

Difficult ground conditions have plagued the underground operations at Mount Windarra since mining started in 1974.The ore at Mount Windarra consists of seven vertically dipping, sub vertically plunging ore shoots. The ore zone in which the shoots lie is characterised by moderate to heavy cleavage and the presence of serpentanite. The ore is known to extend to 1100 metres below surface.Long hole open stoping under cover of backfill has been used as the primary mining method at the mine, but its poor performance brought the mine near to closure in 1984. The mine had been closed from 1979 to 1980.

Jan 1, 1985

By Katsuyama K, Nag DK

Three aspects of rock mechanics, namely, in-situ stress estimation by acoustic emission (AE) method, strength of rock mass and role of chemicals to reduce the strength are covered. It is possible to detect the previously applied maximum stress by stressing a rock specimen to the point where there is a substantial increase in AE activity. This is known as Kaiser effect. From the AE signatures in the second and subsequent loadings, AE take-off point was identified more easily than in the first loading. In determining the compressive strength of rock mass, two factors have to be considered, namely, the size effect on the compressive strength of intact rock and the effect of discontinuities on the compressive strength of rock mass. Although a modified Bieniawski criterion gives best agreement with the triaxial test data, modifications have been suggested to Hoek-Brown criterion due to its popularity. It is possible to reduce the tensile strength of sandstone by saturating it with weak chemical solutions made with dodecyltrimethyl ammonium bromide, polyethylene oxide and aluminium chloride by up to 30%. In the case of compressive strength, there is no appreciable effect. The possible explanation is that the chemical solutions produce an effect on the strength of sandstone only when the failure mechanism is dominated by tensile mode.

Jan 1, 1998

In discussing the Asia-Pacific region weare talking about a region which has more than 60% of the world's population, a regional economy which will in 10 years be larger than the European Economic Community, and a group of countries with some of the highest electricity generation growth rates in the world. It is economically the most dynamic region in the world.

Jan 1, 1990

The kinetics of desorption of nitrogen from molten iron were investigated using the electromagnetic levitation technique. The respective influences of gas flow rate and surface active element (S) were examined. A second order behaviour with respect to the nitrogen concentration in the melt prevailed at all experimental conditions. Sulphur had a marked inhibiting effect on the desorption rate. The experimental results on the rates of nitrogen desorption have been interpreted with the aid of a reaction mechanism consisting of a sequence of elementary steps.

Jan 1, 1991

By Wadsley MW

This paper gives an overall view of the CSIRO-SGTE computer system for thermodynamic calculations. The basis of the system is the coupling of a large self-consistent numeric data bank of thermodynamic information to a modular set of application programs. These seven programs cover management of data files, calculation of thermodynamic properties for species and reactions, plotting of predomin- ance area diagrams, equilibrium and enthalpy balances for complex processes, analysis of thermodynamic efficiency and the estimation of unknown properties. The data bank contains a wide coverage of species and data types so that the system may be applied to many areas of chemistry and metallurgy.

Jan 1, 1984

MOUNT STEWART is situated half a mile south of Leadville railway station, which is distant 240 miles by rail from Sydney via Mudgee. It forms a low ridge from which rock waste and alluvium slope gradually to the black-soil flats of the Coolaburragundy River. The Mt. Stewart mine comprises:(a) The Mt. Stewart workings in M.L. 44, parish Talbragar, Co. Bligh.(b) The Grosvenor workings in M.Ls. 44 and 45, parish Talbragar, Co. Bligh.(c) The Extended workings in M.L. 44, parish Talbragar, Co. Bligh.The workings contain 1375 ft.. of vertical shafts, 1105 ft. of underlay shafts, 800 ft. of rises and winzes, 8520 ft. of drives and crosscuts, and 18,000 ft. of stapes.The mine was first opened in 1888 as a silver-lead mine, and a waterjacketed furnace was erected during 18B2. The furnace was installed with two internally-fired tubular boilers of 35 h.p. and 25 h.p. respectively, and two Baker's rotary pressure blowers. The results of the smelting campaign indicate that, during 14 months, a total of 15,000 tons of ore were treated, yielding silver and lead. In addition to this, a quantity of matte was sold containing about 8000 oz. of silver. As a result of the treatment...

Jan 1, 1925

An investigation was made into the mineralogical characteristics of the upper portions of the 650 and 750 copper lodes. The investigation was based on a comprehensive suite of geological specimens representing all types of mineralization encountered during mining until the end of 1954 and the chief aims of the investigation were to determine (a) the minerals present and their textures and associations, (b) the paragenetic sequence of deposition of minerals in the orebodies, (c) significant changes, if any, which could be found in the orebodies with depth, and (d) the nature and mode of occurrence of nickel in the ore. The general structure of the orebodies is outlined and their mineral composition given. 10 textures exhibited by the ore minerals are described and a paragenetic sequence of events in the formation of the copper orebodies is outlined. No decrease in the complexity of the sulphide mineral textures with depth could be seen and no evidence was found to suggest that the tenor of the ore would decrease with depth although some factors which may eventually limit the extent of the orebodies are noted. The mode of occurrence of minor elements in the orebodies is described. Notes on the occurrence of pyrite, aikinite and berthierite in the orebodies is given and the orebodies are considered to be identified with LiIidgren's mesothermal type of sulphide ore deposit in which considerable replacement of older by younger generations of sulphide minerals occurred.INTRODUCTIONA mineragraphic study was made by Stillwell and Edwards (1945) of a suite of specimens submitted by Mount Isa Mines Limited from the Mount Isa Black Star copper orebodies with a view to determining 1. the nature, extent and association of arsenic, antimonyand bismuth minerals, 2. the mode of occurrence of silver and 3. whether galena and sphalerite occurred in minute forms and below the sizes readily observed in hand specimens.

Jan 1, 1961

Australia is the Western world's largest producer of alumina, supplying one third of total needs. Western Australia's South-West has the greatest concentration of alumina production in the world, with a current annual production rate in the region of 6.8 million tonnes per annum, over 20 per cent of the total supplied to market economies. The value of this production in 1989-90 was 2.34 billion dollars, a very significant contribution to the economy of the State (1). This is despite the fact that the bauxite from the Darling Range is the lowest grade that has ever been commercially exploited, and despite the geographical isolation of the region. It is therefore of great importance to the National and State economies that this industry retain its competitive edge, particularly in the current times of economic downturn. One essential ingredient of this competetiveness is technology and innovation, which can be assured by the committment of the industry to an active program of Research and Development, with support from the public sector as Appropriate.

Jan 1, 1991

The gossan developed from the Whim Creek Cu-Zn-Pb-Ag sulphide deposit, in the Pilbara region of Western Australia, occurs near the top of a ridge in a dissected plateau 01 moderate relief. The gossan is characterized by the abundance of secondary ore minerals which indicates that it is relatively immature, due to climatic conditions and erosional stripping.The abundant presence of secondary carbonates indicates that the low pH generally resulting from sulphide oxidation has been neutralized, probably by the buffering effect of carbonatcs and silicates. Fe, Cu, Pb, 'Ag and Sn have been enriched in the gossan relative to the primary ore, and Mn, Ti, Co and Ni have been strongly depleted; other elements have remained substantially unchanged. The gossan has a strong gcochemical signature characterized by high Cu, Zn, Pb, As, Sb, Sn, Ag and Mo coutents. Boxwork textures are poorly developed, bu't the gossan has other diagnostic mineralogical features including sulphide inclusions in quartz and the presence of residual cassiterite.

Jan 1, 1982

Aluminium in Australia, and in fact all round the world, is made virtually exclusively by the Hall-Heroult process, whereby the metal is derived from the electrolysis of alumina dissolved in an electrolyte comprising fluoride salts. It is the distribution and control of these inorganic fluorides during and after the reduction process which go to make up the bulk of environmental problems associated with aluminium reduction smelters. The emission characteristics of fluorides from the process, the occurrence and effects of fluorides in the environment, and the control techniques wnich are applied in industry, all need to be taken into account in assessing the overall environmental aspects of aluminium Production.

Jan 1, 1977

Increases in mechanisation and mining at greater depths are leading to additional problems of heat and humidity in many mines. As a result there is now an escalating demand for temperature prediction simulations appli- cable to underground environments. After a brief review of the present situation with regard to world mining and the use of environmental programs, the paper goes on to discuss in moderate detail the mathe- matical modelling of the many parameters that govern the condition of the ventilating air in a mine. The development of a program that gives the temperature distribution for a mine ventilation system is then outlined. The practicality of the program is discussed and the presentation format for users is explained. Simplification of input data requirements and the acquisition of data from other planning programs are an integral part of the commercial application of this program.

Jan 1, 1977

By Eckersley J, Boyd G

A brief review is presented of the mechanisms and causes of spoil pile failures which have occurred at the Goonyella Mine. In particular, the results of a recent geo- technical investigation of the spoil dumps in the Cleanskin pit are briefly presented. Spoil pile hydrology is discussed in relation to the use of effective stress concepts in the analysis of spoil pile stability. Experience in relation to stabilisation of dragline dumps is discussed as well as the likelihood of current techniques being success- ful in the prevention of gross failures if prestrip material is placed in existing spoil piles. Parameters exerting a major control on dump stability are outlined.

Jan 1, 1981