Search Documents

South Crofty's ventilation network is large and complex. Of the total exhaust air quantity 40% enters the mine by leakage routes through old workings, this air carries high concentrations of radon gas and results in the mine becoming a classified work place under the Ionising Radiation Regulations 1985. Improvements in the control of the ventilating air and dilution by increased air quantity have reduced the average contamination to aelow-0.2 WL. The major part of the radon originates from ground water inflows and from concentrations of radium within the mine with direct emanation from rock surfaces being negligible. Of 600 kBgs-1 total radon leaving the mine 93% cannot be accounted for from known and accessible sources.

Jan 1, 1988

By P W. Cleary, M D. Sinnott

Cross-belt cutters are commonly used for sampling coal. They are generally cheaper than falling-stream cutters, particularly when a cutter must be retrofitted. The major mechanisms thought most likely to lead to sample bias are being investigated by discrete element modelling (DEM) in a project funded through the Australian Coal Association Research Program. This paper describes a benchmark run and the current direction of research.

Jan 1, 2008

By Just GD, Phillips R

The application of high pressure water jet technology to the drilling of longholes in coal has resulted in the development of a system currently capable of drilling to lengths greater than 200m. Field tests at the German Creek Mine have demonstrated directional control of the holes within a 0.5m section of the seam. Initial application of the technique at the German Creek operations is for drilling methane drainage holes. These developments, in three stages, result from support by the National Energy Research Development and Demonstration Council

Jan 1, 1991

By Koginmo V. I

The concentrator at Bougainville Copper Limited has an annual throughput of 48.2 million tonnes/year producing approximately 175,000 tonnes copper, 16.1 tonnes gold, and 50 tonnes silver. Conventional three stage crushing and screening are used to reduce run of mine ore to an average product d80 size of 6.7mm. The primary objective of the crush- ing plant is to provide a continuous supply of ore to the 12 primary grind- ing mills via an intermediate 300,000 tonnes capacity stockpile. Since ball mill performance improves with decreasing mill feed size, the crushing plant continually strives to produce the finest possible product for mill- ing. This has been achieved by increasing plant availability and total installed power, and improving crusher manganese liner life, screen cloth life, and plant operating practices. A recent innovation was the installa- tion of a 35 million tonnes/year preconcentration screening plant in Janu- ary 1987 to recover high grade fines from low grade run of mine ore types in which the mineralisation occurs preferentially along fracture planes in the parent rock.

Jan 1, 1988

Mining has long been an important activity for the people of Australia. The Aboriginals used rocks and minerals in their culture many thousand years before European settlement. It was not until 1840 that silver-lead ore was discovered in the Mount Lofty Ranges, and developed as Australia's first metalliferous mine.

Jan 1, 1995

By Grace NC, Lightfoot BW

Small scale trials of the smelting of a copper concentrate in the Sirosmelt submerged lance reactor are described. Pellets of concentrate were dropped into the reactor while injecting air-rich mixtures of oil and air through a lance into a bath of matte overlain by slag. This produced a discardable slag and a matte which was converted in sequential stages in the same reactor to white metal and blister copper. Difficulties were encountered in determining the end points of the converting stages but control techniques were developed to allow successful operations producing blister copper. Deportments of minor constituents of the concentrate to slag, matte,metal and fume for the three stages are reported and possible applications are Discussed.

Jan 1, 1980

By Veal FL

Technological changes in Portland cement manufacturing during past years have reflected changes in the economics and availability of various types of fuel such as coal, fuel oil and natural gas. The industry consumes a sig- nificant quantity of both thermal and electric- al energy. The nature of the process and its chemical constraints does however permit the use of comparatively low grade fuels such as high ash coal and high sulphur oil. In striving for increased daily kiln outputs and conservation of energy, there is a worldwide trend towards the use of dry process plants. Wet process kilns of about 2 500 tonnes per day assume massive component sizes which present difficulties in manufacture, and transport to plant sites. Large capacity dry process units in excess of 8 000 tonnes per day are now in operation using precalcination techniques in which part of the fuel is introduced in the static preheater section ahead of the kiln while the balance is added to the kiln in a conventional manner. This technique has virtually doubled the potential output of any given single kiln.

Jan 1, 1976

The results of the washing of coal are often presented by using Partition Curves. By analogy, it is possible to express the results of screening by using similar partition curves. As in the coal washing processes, this method determines the accuracy of screening and is also suitable for different separations depending on the difference in size distribu- tion. This method compares the effectiveness of two screening operations and forecasts the performances.

Jan 1, 1984

By L R. B M Sß

This paper presents the results of a liberation study made on a sulfide copper ore from Carajßs, Brazil, in a mini pilot plant flotation test. The aim of the research was the methodological evaluation of a liberation study using a sample crushed at 1 mm and a sample ground for flotation testing to a target size of 80 per cent

Jan 1, 2005

Mining Automation By Professor Hugh Durrant-Whyte, Australian Centre for Field Robotics and Centre for Mining Technology and Equipment, Department of Mechanical and Mechatronic Engineering, The University of Sydney Professor Hugh Durrant-Whyte summarised why the mining industry needs to automate and reviewed the current automation technology - its risks, costs and benefits. Why automate? The drivers for automation include: safety, productivity, quality control and reduced manning, equipment utilisation, maintenance, and organisation and planning. Durrant-Whyte recommended starting out with a picture of a fully automated mine and working backwards through a systematic analysis of benefit and risk. This also involves looking at the impact of the total automation on current mine design, and identifying the key technologies.

Jan 1, 1997

Currently there is considerable interest in the production of DRI in Western Australia to take advantage of intense interest from the Asian market. Most DRI is produced using gas-based processes and is used as a feedstock in electric arc steel furnaces, otherwise known as mini-mills. This paper critically examines the technical and economic issues of various gas-based DR processes available today and recommends the most effective and attractive processes suitable for Western Australian iron ores.

Jan 1, 1996

Examples are given of the different management approaches used to improve a mine's profitability and the view is put that attention to mine design is very important but easily overlooked. The need for humans to use graphics to ccanprehend and develop strategies to exploit ore deposits is discussed. The use of two and three dimensional representations for geology, mine design and survey data is reviewed. The current use of computers in mining is discussed and reasons for the limited use of ccanputer graphis are proposed. Suggestions are made as to how more extensive use may be made of catputer graphics in mining by using recent and possibly forthcoming advances in computer hardware and by adopting certain software approaches.

Jan 1, 1983

By Andersen AK

A previous paper (1) indicated that electrowinning of copper at current densities considerably higher than those currently employed in electrowinning operations is technically feasible. It is of interest, therefore, to establish the extent of economic benefits which may be obtained from high current density operation and to determine the value of the optimum current density. Optimization of electrorefining processes has been discussed in considerable detail by Ibl (2) and Schmidt (3) whop from theoretical considerations, derived expressions for the optimum current density. In this work, general equations relating both the capital investment and the production cost for copper electrowinning plants to current density and plant capacity are established. From these equations, the optimum current density can be calculated for any desired plant capacity.

Jan 1, 1969

By Baynes F. J, Bermingham A. G

The 6000m long King Headrace Tunnel will be driven through hard Owen Conglomerate in the Eastern third and feldspar porphyry in the Western two thirds, with the anticipated hardness up to 350MPa unconfined compressive strength. Since the Commission had not driven a long, large diameter tunnel for some twenty years, major research was undertaken to assess the current tunnelling trends. Tunnel boring machines were compared with drill and fire equipment. Rail equipment was compared with rubber tyred equipment. Tenders were called with tenderers invited to submit alternatives if desired. Commissioning and production excavation using the equipment is discussed with the final conclusion being that the individual items of equipment purchased combined to make an efficient hard rock drill and blast system capable of progressing through all rock conditions likely to be encountered on the King and Anthony Schemes.

Jan 1, 1987

The Western Australian Mining and Petroleum Research Institute (WAMPRI) was established in 1981 by the Western Australian Government as a funding and co-ordinating Institute to foster research into the mining and petroleum industry within this State. To June 1984, the Institute has sponsored 34 projects with a total notional value of $2.5 million and an actual cash commitment of $1.5 million. Strong support for WAMPRI has come from Industry with 60 companies contributing half the money needed for the research grants.The 34 WAMPRI projects funded so far cover all aspects of the mining and petroleum geosciences.Several WAMPRI projects are concerned with gold including processing technology and the development of exploration models and techniques, they are providing successful results.Although well supported by Industry there is a surprising lack of applications being submitted to the Institute in the area of mining engineering, where it is felt there is much scope for research projects.

Jan 1, 1984

The collapse of the I.T.C., the subsequent fall in the price of Tin, and the lifting of quotas saw the Renison concentrator resuming full seven- day operations at maximum capacity in 1985/86. Performance was sus- tained in terms of grade and recovery, and in some areas improved, over this period. A further challenge was declining head grades, and the need to treat higher proportions of less amenable ore types. The complexity of the flowsheet and the method of mining and ore handling predisposes the process to unstable operation, and solving this problem comprises a major component of the current development effort. The concentrator has an imbalance of capacity between processes, and excess in some areas is being adapted to enhance the capacity of others. Magnetic susceptibility of various minerals is being exploited to greater effect. Significant performance gains are achievable by improving exist- ing unit process efficiency, particularly in grinding, gravity processes and Cassiterite Flotation. This paper reviews the metallurgical developments, both recently implemented and planned for this year, which have contributed to main- taining Renison Limited in a competitive position in the post I.T.C. Tin industry.

Jan 1, 1988

By P Townsend, F Russell

Palabora Mining Company operates an integrated open pit mine, concentrator, smelter and refinery complex located in the Northern Province of South Africa. The Palabora open pit went into production in 1966, mining 30 000 t/d to produce some 62 000 tpa of copper. With continuous modification and improvement, a mining rate of 82 000 t/d, producing up to 135 000 tpa of refined copper, has been achieved. While these improvements have also enabled the mine life to be nearly doubled, the open pit will reach the end of its economic life by 2003. The Palabora orebody is vertical and the reserve extends to a depth of 1800 m over an area of 700 m by 200 m. Studies to assess the economics of mining the orebody by underground means began in the mid-1980s. These studies indicated that block caving is the lowest cost underground mining method that would generate a suitable return. In March 1996, a decision was made to develop a 30 000 t/d block cave mine that will extend the life of the Palabora Mining Company by a further 20 years. In terms of the relatively high rock strength and the resultant coarse fragmentation that is expected at the drawpoint, the Palabora cave can be considered rather unique when compared to other block cave operations. This paper describes the project in broad terms and details the mining method, particularly with respect to the cavability of the orebody and the design features to deal with the coarse fragmentation. The project commenced in July 1996 and final development of the undercut and drawbells is scheduled for completion in November 2003. This paper describes the status of the project and planning as of April 2000.

Jan 1, 2000

By Trutwin W, Tracz J

The outbreak of open fires underground cause disturbances to the conditions of the mine ventilation process. Thermal and chemical effects due to fire create unsteady, transient states in airflow and the spread of combustion products in the mine ventilation network. Changes in airflow have an influence on the fire, constituting a sort of feed-back between the fire and the ventilation process. This paper deals with a numerical simulation method, which enables the determination of transients caused by fires. The mathematical model, of the simulation method considered, has been based upon a: simple model of combustion of fuel in the airway, unsteady exchange of heat between the fire, airflow and surrounding rocks, airflow in mine ventilation networks and the theory of heatflow in the rocks. Initial and boundary conditions allow the determination of a set of parameters describing the airflow, the propagation of combustion products, the tempera- ture of the fire and flow etc. due to the fire. The simulation method, facilitates a graphical presentation of the spread of combustion products throughout the network. The simulation method has been prepared for an IBM PC/AT Computer.

Jan 1, 1988

By Svenson D

Most exploratory drilling in the N.S.W. coal fields has been conducted using convent- ional diamond drill rigs of modern design, us- ually truck or trailer mounted. Conventional diamond drill rigs have also been used exten- sively by the Queensland Department of Mines for coal exploration. However almost all of the exploratory drilling of surface mine coal prospects throughout Queensland has been conducted using rotary rigs typified by the Mayhew 1000 truck mounted unit. The rotary rig has proved capable of both rapid non-core drilling and core drilling with high core recoveries when modern core barrels have been used by experienced drillers. For deep or continuous core drilling, wire-line equipment is now in general use. Both wire-line and conventional coring is effected using stationary split inner tube barrels, for minimum core disturbance, maximum core recovery, ease and accuracy of logging and sub-sectional sampling. Diamond core bits are generally required in N.S.W., with water circu- lation. In Queensland, the generally softer coal measures strata can be successfully cored using tungsten carbide bits and air circulation is the preferred method where possible.

Jan 1, 1977

By Lane G

This paper addresses project commissioning, that is, activities that culminate in the transfer of a project from the construction phase to routine plant operation. These activities should be initiated early in the engineering and design phase to ensure that the plant design is operator friendly and that construction is scheduled such that pre-operational testing and hand over to the owner occurs in a timely and cost-effective manner. For the purposes of this paper, commissioning includes all activities related to pre-operational testing, no-load testing, water commissioning, and ore commissioning. That is, all activities from construction completion to practical completion of the prime contract. This process is facilitated in numerous ways dependent on the nature of the project prime contract and the size of the project. For small lump sum projects, the contractor's responsibility may include all phases of commissioning to practical completion, whereas, a managing contractor on a complex multi-contract project may only be required to bring the project to mechanical completion and hand over to the owner for ore commissioning. Irrespective of the responsibilities, commissioning programs require careful planning, effective communication and detailed reporting. Unsuccessful

Jan 1, 1997