Search Documents

ALTHOUGH discovered as long ago as 1817, by Strohmeyer, the use of cadmium did not become in anyway general for nearly a century. Its properties, although well known, did not recommend it to users of metals generally, and it was, on the whole, regarded more in the light of a nuisance to zinc producers than anything else. Its real value was not appreciated until both the United States of America and Germany, who are entirely dependent on outside sources for their supplies of tin, were faced with the unpleasant fact that their tin stocks were being rapidly depleted, with practically no prospect of having them replenished. This resulted in serious efforts being made in the UnIted States of America to conserve what tin was available, and, as a consequence, several metals were tried in the hope that they would prove satisfactory substitutes for tin. Among these was cadmium, and it was found that cadmium could replace tin in a manner sufficiently satisfactory to permit of its use in many directions where tin had been used before.It is on this ability of cadmium to replace tin that its use became in any way general at first; but since then new avenues of development have been opened up in which its physical and chemical properties are proving their value. It is highly probable that its use will extend very considerably as time goes on. OCCURRENCE OF CADMIUM.There are several cadmium minerals known, but none of them occur in profitable quantities as ores. The cadmium of commerce is derived almost entirely from zinc minerals and ores in which it is almost invariably present in proportions which are usually very small. Cadmium behaves metallurgically almost the same as zinc, and hence constitutes a fraction of 1% of almost all spelter.

Jan 1, 1923

By Rogis J

The basic parameters causing outbursts are rock pressure, gas characteristics and the physico-mechanical properties of the coal. The three sets of factors are to some degree interdependent. At Collinsville, the gas characteristics coupled with the physico-mechanical properties of the coal appear to be the major factors contributing to outbursts. The relative importance of rock pressure is uncertain. The following geological parameters appear to be necessary before outbursts can occur. 1. A coal rank greater than 1.2% vitrinite reflectance. 2. Thrust faults with throws greater than 3.Om or strike- slip faults with coal gouge wider than 0.3m. 3. Seam gas emission values greater than 1.1 cm3 /g. Igneous intrusions are the likely source of the carbon dioxide seam gas. Outbursts have occurred at depths ranging from 215m to 265m. They occur at these relatively shallow depths due to: 1. the high rank of coal at the present topographic surface and the high coalification gradient; 2. the relatively high degree of tectonic deformation of the strata; 3. the seam gas characteristics; and 4. the extent of igneous intrusions.

Jan 1, 1980

By Moy A. D

The Esperanza deposit is located 120 kin N of Mount Isa, Queensland at approximately lat 19¦20'S, long 139¦22'E on the Camooweal (SE 54-13) 1:250 000 scale map sheet. It is one of several structurally controlled copper ¦ cobalt deposits developed along the Mount Gordon Fault zone and related faults, within the Western Fold Belt of the Mount Isa Inlier (Figure 1). Together with the nearby Mammoth orebodies it forms the basis of the Gunpowder operation of Aberfoyle Limited. Until recently ore was mined from the Mammoth orebodies by open stoping with decline haulage to surface leach pads. Leaching of in situ broken ore (in place) and surface heaps, followed by solvent extraction and electro-winning (SX-EW), produced copper metal on-site. In March 1997, mining was suspended at Mammoth and the focus of the Gunpowder operation switched to development of the Esperanza orebody, which is expected to begin open cut production in mid 1998. SX-EW methods will produce 44 000 tpa of copper from an expanded plant. The pre-mining mineral resource at Esperanza (measured, indicated and inferred) is estimated at 4.6 Mt averaging 7.7 per cent copper.

Jan 1, 1997

By Bhattacharyya A. K>

The Pemali Open Pit Mine is situated in a small island called Bangka in Indonesia. It produces approximately 165,000 m3/year of tin ore with an average grade of 3.67 kg/m' of tin from a primary deposit. The deposit occurs at the rim of a granitoid intrusion within sedimentary beds. The rock formations, all extremely weathered, and the overlying alluvium, are exposed to a rainfall exceeding 3m/year. Serious slope stability problems are experienced at the mine, despite using overall pit slopes of 20¦-29¦, the latter resulting in a stripping ratio of 4:1. This paper outlines a computer based back analysis of a major slope failure involving some 250,000 m' of material which occurred on the west wall of the pit in February, 1984. The findings from the analysis, together with other information, are used to examine the stability of the east wall of the pit, where tension cracks developed later. The results indicate that the large influx of water was the most significant cause of such slope stability problems and a more intensified water management programme would be beneficial.

Jan 1, 1989

This paper summarises the current status of the mining sector in Poland in terms of vertical transport system safety. Selected results of research programs conducted at the AGH-UST relating to mine hoist system safety are reviewed. The conclusions support the notion that the costs of vertical transport systems can be reduced, while at the same time maintaining the required safety and reliability levels. Novel solutions: movable fender beams HWR, linings modar« and the integrated shock absorbers PHH for conveyance guiding systems fully confirm this hypothesis.

Jan 1, 2005

By Low Russell

Mark Westfield, writing in The Australian on 16 May 1994 stated: The role of the independent expert is crucial to Australia's investment system. When it falls down, there can be very dramatic consequences. The scope of these consequences was dramatically illustrated in the decision of Rogers J. at first instance in Cambridge Credit Corporation v. Hutcheson (1983) 8 ACLR 123 when the auditors of the failed company were found liable for breach of contract and faced a damages award of $145 million, well in excess of their insurance cover. No comfort should be sought in the fact that this decision was overturned on appeal, for the result of the appeal rested on whether there had been a causal connection between the breach of contract which had occurred and the loss suffered, rather than on the fundamental principle of auditors' liability. Thus: Those who prepare experts' reports in company cases carry a heavy moral responsibility, whatever their legal duties may be... Unless high standards are observed by those who prepare these reports, there is a danger that systems established for the protection of the investing public will, in fact, operate to their detriment through reliance placed on those reports and on the reputations of those who furnish them. In lending his name, the expert will often, as in this case, be lending a name to conjure With.

Jan 1, 1995

The comminution process indicates that the most energy-efficient comminution system would be one where the particles leave the breakage field as soon as they reach product size. Contrary to the free falling gravitational (vertical) flow in crushers, the grinding millÆs energy efficiency essentially depends on ore characteristics and the discharge rate of broken particles, which in turn depends on how efficiently the discharge pump (grate and pulp lifters) operates. The essential function of a pulp lifter is to transport the broken material and slurry from the discharge grate out of the mill. Hence, the design optimisation of pulp lifters affects not only the energy efficiency and throughput of autogenous grinding/semi-autogenous (AG/SAG) grinding mills, but also contributes other process benefits such as improved wear life and operator-friendly steady and smooth mill operation. Following its introduction in 2006, OutotecÆs patented Turbo Pulp Lifter (TPLÖ) design has been retrofitted at existing sites and also installed in some new ones around the world. This paper will provide operational experience and data on how the TPLÖ design has allowed AG and SAG mills to operate efficiently.

Jan 1, 2009

By F Melcher, M Wiedicke, A Wittenberg

Ferromanganese nodules form a specific category of widespread marine mineral deposits. The tremendous increase in metal prices during the last decade raised new economic interest in their exploration. The German Federal Institute for Geosciences and Natural Resources (BGR), which had been engaged in nodule research in the 1970s and 1980s, renewed its activities on this subject based on an exploration contract with the International Seabed Authority, signed in 2006. BGRÆs licence area û comprising 75 000 km2 û is located between the Clarion and the Clipperton Fracture Zones. In this so-called nodule belt north of the equator the sea floor reaches water depths of >4000 m. About 900 million tonnes of manganese nodules are expected there. In this study the fine-scale distribution of important elements in manganese nodules and crusts from a variety of locations was investigated. Besides 11 samples from the RV SONNE cruise SO-25, numerous samples from additional locations were included in this study for comparison. In general, the sample suite includes two genetic types of precipitates, manganese nodules and Co-rich crusts. A detailed characterisation of the distribution of major, minor and important trace elements in manganese nodules based on in situ microenergy dispersive X-ray fluorescence (¦-EDXRF) analysis is presented here. The data are compared with bulk major, minor and trace element data as well as with quantitative electron probe microanalysis (EMPA) data sets. The element distribution maps and profiles produced by ¦-EDXRF analysis with short or extended (in case of profiles) counting times, allow precise selection of æregions of interestÆ for further detailed investigation using high spatial resolution techniques (eg scanning electron microscope (SEM)-EDAX; laser ablation-inductively coupled plasma mass spectroscopy (LA-ICPMS); isotopic studies).

Jan 1, 2008

By D E. Ralph, D-J Kim, G-J Ahn, Y-H Rhee

The amount of discarded dry batteries are presently found to be increasing globally and waste cathode active materials of the lithium ion battery industry are among them. Hydrometallurgical operations are being applied to recover the valuable metals from these waste batteries. To find an economic and environmentally friendly process, the bioleaching process was applied in the present investigation for recovery of valuable metals. Its principle is the microbial production of sulfuric acid and simultaneous leaching of metals. Bioleaching of spent lithium ion secondary batteries, containing LiCoO2, has been studied in this investigation. A new method for recovery of cobalt, potentially the basis of an economic and environmentally friendly process was examined. The present study has been carried out using chemolithotrophic and acidophilic bacteria Acidithiobacillus ferrooxidans, which utilises elemental sulfur and ferrous ion as the energy source to dissolve metals from spent batteries. Bio-dissolution of cobalt was found to be faster than lithium. The effect of initial Fe(II) concentration, initial pH and solid/liquid (w/v) ratio were studied in detail. Higher Fe(II) concentration showed a decrease in dissolution due to co-precipitation of Fe(III) with the metals in the residues. Similarly, at higher initial pH values and higher solid/liquid ratio (w/v) metal dissolution was found to be inhibited. The optimised conditions for bio-dissolution were solid/liquid (w/v) ratio û 10 g/L, initial Fe(II) concentration û 3 g/L, elemental sulfur û one per cent (w/v) and initial pH û 2.5. In the optimised conditions, cobalt dissolution was observed to be about 60 per cent, whereas that of lithium was ten per cent after 20 days. A first order kinetic model was derived to study the rate of dissolution of both the metals.

Jan 1, 2006

The difficulty of successfully imple menting a landscape policy is almost incom- prehensible. Landscape design is recognised as an essential component in the integration of engineering and architectural projects into the landscape, but the factors which prevent the achievement of a successful result are rarely recognised or assessed. In many cases these prohibiting factors are due to a lack of understanding of the effect of major planning decisions on the existing landscape, the importance of the landscape plan and the significance of appro- priate specified techniques to prevent un- necessary damage and to ensure retention of existing vegetation in a healthy condition. The role of the landscape architect in incorporating new land uses into the landscape provides the background against which factors which inhibit policy achievement can be con- sidered.

Jan 1, 1976

Although technology and circumstances are in a constant state of change, the principles of managing the human element remain constant. The isolated mining community continues to form the backbone of the minerals industry but the nature of the isolation, along with the economic and political environment of the industry, is changing. These changes require new inputs by management to the workforce. Management must determine an effective working relationship with unions on its mine site and concurrently contribute to the build- up of the expertise of the individual worker through training and communication. It must also retain a proper balance, by way of human contribution, in cost and information reporting and in other areas amenable to computerisation. These comprise the aids to management necessary to achieve the desired operating efficiency and profitability.

Jan 1, 1980

The exploration methods used by the British Coal Corporation in 1990 improve the geological reliability of underground coal production. Although some of the techniques in common use have been proved to be effective, their limitations are recognised and concentration has been on the increasing integration of direct and remote sensing techniques. Attention is focussed onto first seam workings in sections of at least 2 metres in the depth range of 400-1200 metres and covers both surface and underground exploration. The case studies of exploration techniques and their effect on mine design at several existing collieries are representative of a wide range of geological environments within the more productive British coalfields. Notwithstanding such improvements in exploration and geological reliability, further new exploration technology is currently being investigated or trialled by British Coal.

Jan 1, 1991

By Huajun W, Long LZ

The composition of fly ash and formation mechanism of cennospheres are introduced in this paper. The signification of using this potential new mineral processing resource is emphasised. The beneficiation properties of the components of fly ash, such as susceptibility, specific gravity, size, shape and flotability etc have been examined in detail. A technique was designed to process fly ash from the XiGaoJing power plant in Beijing, and a flowsheet is also presented. Flotabld cennospheres, magnetic beads, sinkable beads, carbon and advanced pozzolamics can be obtained as separate products through this flowsheet. It is emphasised that the beneficiation of fly ash is an efficient means of totally utilising the resource. Examination of the products show that they have good physico-chemical properties. Possible areas of their application are also Suggested.

Jan 1, 1993

Determining the environmental consequences of green field projects is becoming an increasingly important component of new projects. Feasibility studies are regarded by potential investors as incomplete if a comprehensive Environmental Impact Assessment (EIA) has not been completed. These EIAÆs need to meet various local and international requirements in order to achieve bankability. Heavy mineral mining projects are often located in ecological sensitive coastal zones, and bring with them a suite of social impacts in the mainly developing countries within which they are usually located. This paper draws on experience gained in undertaking EIAÆs for heavy mineral mining projects in Kenya, Mozambique and South Africa, and uses these case studies to identify potential pitfalls. Important lessons include the need to initiate the EIA process as early as possible in the project, in order to develop management systems to mitigate the environmental impacts of exploration. Close and on-going consultation with affected communities is also seen to be critical to the success of the EIA. Proactive participation on the part of the environmental consultants with the project team and all interested and affected parties (IAPs) is important. An EIA commissioned later in project planning makes it difficult for the EIA to contribute in a positive manner to the project. Early engagement with environmental consultants allows the environmental assessment to develop from a report to an actual process, and to become fully integrated with project planning. The proviso is that an initial æfatal flawÆ assessment is required to identify any potential æshow stoppersÆ, in order to meet one of the important objectives of EIA, namely an assessment of whether or not the proposed project is the preferred development intervention in the study area. For more controversial proposals this may require the commissioning of a Strategic Environmental Assessment (SEA), which circumvents some of the limitations of the project level EIA. Whilst confidentiality is a constraint to full disclosure, an open participatory approach to public consultation is essential to add credibility to the EIA process and to gain, at least, the acceptance of the process from the majority of IAPs. Full disclosure is encouraged by organisations such as the International Finance Corporation, who acknowledge that good public consultation costs a lot of money, but bad public consultation costs a lot more! An open approach to disclosure presents understandable difficulties for proponents, as they are required to give up some of their control over the project, and to trust the social scientists engaged in the process. However, independence in the EIA process is critical to its success. This paper will highlight these and other issues by drawing on five case studies to identify lessons learnt, and explore the above themes in more detail.

Jan 1, 2001

By Locke CA

Geophysical signatures of the Taranaki and Tongariro volcanoes reflect similarities in their age, composition and hydrothermal histories, but also reflect differences in host rock settings and edifice evolution. The Taranaki volcanoes have strong positive gravity anomalies showing that their edifices largely consist of dense andesite which reflects substantial lava production or dyke injection during construction and that large sub-edifice dykelstock complexes occur. In contrast, the Tongariro volcanoes have strong negative gravity anomalies indicating low density edifices of volcaniclastic material; no sub-edifice intrusions can be identified, probably because of the lack of density contrast with host basement rocks. Strong positive magnetic anomalies over the younger cones can mainly be attributed to near-surface andesite lavas or dykes whereas subdued magnetic effects are associated with hydrothermally altered zones within both edifices and sub-edifice intrusions.

Jan 1, 1995

By Dawes S

Efficient roof control in colliery operation is a factor that must be maintained for· the maximum reQovery and economic extraction of the mineral. It must be carefully considered in each of the following stages in the life of a mine.1. The primary development and the first working of the mine.2. The maintenance of access roads, intake and return airways.3. The extraction of pillars.FACTORS IN ROOF CONTROLThe main objects of roof control are: The support of the roof in working places, the relief of roof pressure from the workings during pillar extraction, and in some instances the prevention of subsidence of the surface.The support of the roof during development operations and first working, and the subsequent maintenance of these is influenced by:-1. The depth of the seam below the surface.2. The thickness of the seam.3. The dip of the seam.4. The condition of the roof and floor.5. The method of extraction-mechanical or by hand.6. The method of. working-Iongwall or bord and pillar.7. The availability of material.As a general rule, the pressure exerted by the superincumbent strata may be taken as one pound per square inch for each foot of cover, and the crushing strength of coal as 1,500 to 2,000 lb. per square inch; this, of course, varies, but from these figures it may be assumed that seams below 2,000ft. in depth are liable to crush. If any part of the seam is removed, added weight is thrown onto the remaining coal. It is therefpre essential that for effective working this extra weight must be removed or supported as soon as possible.The outstanding principle in the support of mining excavations is to ensure that the supports are set as soon as possible after the natural support has been removed.Where a system of bord and pillar is applied, the early setting of supports reduces the extent to which the roof bends, thereby reducing the liability to ·tension fractures at the centre of the road.

Jan 1, 1947

The last two years have seen a rapid change-over from mechanised cut and fill. stoping to the more economic and productive long hole open stoping method, such that today more than 80 per cent of total production is won from open stopes. At first drilling was by sub-level rings and/or parallel up and down holes from inter- mediate sill horizons using conventional exten- sion rod equipment. Sub-levels were developed no more than 40 metres apart to allow accurate drilling. Compact, crawler mounted in-the-hole hammer equipment was introduced as soon as it became available in Australia. Today, all open stope drilling is done with three Atlas Copco ROC306 rigs and two Ingersoll-Rand CMM jumbos. Fans of 115 mm diameter holes, varying from near vertical down holes to horizontal, are drilled with a burden of 3 m. Toe spacing varies from 3.5 m to 4 m. An Atlas Copco DG418 booster compressor is used to boost run-of-mine air from 700 kPa to 1400 kPa in the areas of longest drilling. This has improved overall drilling performance in these areas by 40 percent.

Jan 1, 1977

By Korsch RJ

Permian oroclines in eastern Australia must have formed by sliding on a detachment surface. It is identified as a westward- dipping Devonian and Carboniferous sub- duction zone. Major strike-slip faults probably sole out on the same surface. One major fault with an associated serpentinite belt was pulled away from the craton abd bent into loops. Basins formed in the loops.

Jan 1, 1987

Natural gas from the south west Queensland gas fields is now available in north west Queensland to fuel the development of many Carpentaria Mineral Province projects. Like these projects, the south west Queensland gas project, developed under the operatorship of Santos Ltd, has its own æMining CycleÆ. While the project is entering its third expansion phase, it is at the same time actively extending its discovery phase, with large programs of gas exploration and reserves definition. This paper outlines the history of the south west Queensland gas project, with particular emphasis on the relationship of the project to north west Queensland.

Jan 1, 1998

By A Whaanga, A Doecke

The internal stratigraphy of the Marillana Creek palaeochannel Tertiary channel iron deposits (CID) in the Hamersley Province of Western Australia was initially defined in the 1980s and redefined as the Marillana Formation in the early 2000s. Recent drilling, open pit mining and field observations in the Western deposits at BHP Billiton Iron OreÆs Marillana Creek tenements have revealed some additional details on the extent and detail of some units of the Marillana Formation stratigraphy in this area. The drill hole data at Western 1 South has identified a number of features either not previously documented in this area or whose significance has not been adequately recognised, including a denatured zone at the base of the Upper CID of the Barimunya Member, and variations in the lithology within the Munjina Member at the base of the channel. Additionally, the Western 4 pit walls show evidence of a significant near-surface clay horizon and overlying CID, which are suggested to be the equivalent of the Iowa Eastern Member in the Eastern deposits. The deposition of this unit was most likely driven by a regional climatic disruption rather than a change in sediment source area alone. The nature of the Weeli Wolli Formation-derived goethitic peloids in the Western deposits may explain the more extensive denaturing in the Western Lower CID of the Barimunya Member. In contrast, the more robust nature of the haematitic-cored pelletoids in the Central and Eastern deposits has resulted in a less denatured Lower CID in these areas. Such work reveals the value of and need for geologistsÆ ongoing face mapping observations and detailed drill hole logging, and cautions against not querying previously accepted interpretations.

Jan 1, 2007