Search Documents

Expansion of the B.H.P. Co. Ltd. mater ials handling facilities, at their Newcastle Steelworks, began in 1964 and continued until 1970. The present complex handles the annual iron ore requirement of some three million tons for the Sinter Plant and Blast Furnaces. Iron ore is discharged from ore carriers and conveyed at rates up to 3,000 t.p.h. to either of two 180,000 ton capacity storage yards, where it is blended using boom stackers. Material is reclaimed from these yards at rates up to 1,000 t.p.h. using a slewing boom bucket-wheel reclaimer and fed to a screening station. Oversize material is scalped out and crushed in a closed circuit cone crusher. Undersize material is sized on double-deck vibratory screens which separate at 1/4in (6mm). The two fractions are blended in two of four 70,000 ton capacity blending yards using slewing boom travelling stackers. Bridge-mounted bucket-wheel reclaimers reclaim the blended piles at 1,000 t.p.h. Fine ore is conveyed to the Sinter Plant and lump ore to a second screening station, for rescreening, before passing to the Blast Furnace.

Jan 1, 1972

By S Yang, J Wang, J G. Ning

A series of conventional dynamic uniaxial compression (CDUC) tests and coupled static-dynamic loading (CSDL) tests were conducted using a split Hopkinson pressure bar (SHPB) system to explore the dynamic mechanical behaviour and fracture characteristics of medium sandstone on a microscale in the laboratory. In the CDUC tests, the dynamic uniaxial compressive strength of the medium sandstone was rate-dependent, while the dynamic elastic modulus was not dependent on the strain rate. Then, we proposed a generalised model to characterise the rate-dependent strength from 17.5 s-1 to 96.8 s-1. In the CSDL tests, with increasing initial pre-static stress, the dynamic elastic modulus and dynamic strength increased nonlinearly at first and then decreased. The results show that two classical mechanical types (ie Class I and Class II) are observed from the dynamic stress-strain responses of the CDUC and CSDL tests. By means of scanning electron microscopy (SEM), the micro difference of post-loading microfracture characteristics in Class I and Class II behaviour was identified. In Class I behaviour, intergranular fracture (IF) usually initiates at or near the grains, most cracks deflected along the grain boundaries, resulting in a sharp angular edge, then coalesces to the main fracture surface that splits the specimen along the direction of stress wave propagation. In contrast, Class II behaviour results from the combined IF and transgranular fracture (TF).

Nov 29, 2022

By F Cesnik, P Griffin, S Green

In July 2004 a flotation concentrate regrind circuit was commissioned in the æHigh GradeÆ Ridgeway concentrator at NewcrestÆs Cadia Valley Operations. This was the culmination of two years of project testing, process design and planning which commenced shortly after commissioning the concentrator in March 2002. During the two-year project evolution alternative grinding technologies were evaluated from conventional ball milling through to sand milling. A Detritor mill was eventually selected for the duty and the criteria on which this selection was based will be presented. As the project evolved so too did the equipment sizing with the concentrator quickly exceeding design capacity of 4 Mtpa and currently averaging 5.6 Mtpa, the process design had to accommodate this and future potential throughput increases. This paper will focus on the supporting testwork, circuit surveys and concentrate properties which were used as the design basis for the project. The economic evaluation which led to the project receiving board approval in November 2003 will also be presented. Detailed design and construction management issues will be discussed as will preliminary results and findings up to November 2004.

Jan 1, 2005

By West Coast Staff

Attention to the design of facilities for drainage, of both surface water and seepage, made it possible to attain, for a qam impounding residues from a concentrating mill, a more stable sand wall which can eventually be carried to a greater height.EXPERIENCE WITH No. 1 DAMResidue from the lead zinc concentrating mill, which treats the ore from the Rosebery and Hercules Mines, was pumped 3,600 ft. through a 5-in. diameter woodstave pipeline to the site of the dam. It was formerly delivered through a 4-in. steel pipeline.State laws prevent the residue being discharged to waste into the Stitt River. Furthermore, as a pyritic residue it is a potential source of sulphur.Between 1936 and 1956 more than 1,000,000 tons. of residue was paddocked. The run-of-mill product was roughly classified at the dam in a 6-ft. diameter cone classifier and the sand fraction was pumped by a 3-in. pump to the front wall of the dam across a shallow valley. The overflow gravitated to the rear of the dam (Fig. 1). Typical sizings were:

Jan 1, 1958

By Chapman RL

A new process has been developed to remove the impurities copper, cadmium, cobalt and nickel from a zinc plant electrolyte by cementation on zinc dust. The process has been tested in the laboratory and in a continuously operated pilot plant. It has been found that cadmium, in the presence of small amounts of antimony in solution, assists the removal of cobalt. Cementation is conducted in two stages: the first stage for removal of copper with a small excess of zinc dust to produce a relatively high grade product, the second stage for removal of cadmium, cobalt and nickel by addition of zinc dust in the presence of anti- mony. The excess zinc and the cadmium present in the second stage cementate can be selective- ly recovered by slow leaching in spent electrolyte. Zinc dust processes in use elsewhere are described and compared with the present system for use in the Risdon circuit.

Jan 1, 1984

Regional problems, such as political risk and debt reschedulings, in Pacific Rim nations coupled with the price volatility of gold mean that multi-faceted financing packages are needed to offset the many risks inherent in a new gold mine development. The cross-border risks of getting money back out of a producing mine may require the involvement of export credit agencies, multilateral government banks, or political risk insurance. Variations on forward gold sales, gold loans, or offset structures can also enhance the flexibility and safety for the providers of both the debt and equity. The region will become as large a gold producer as South Africa by 1990. The large dollar amounts for both investment and revenues realised are of great significance to the economies of many of the Pacific Rim countries especially as a means to increase foreign exchange earnings.

Jan 1, 1987

The Ladolam gold deposit, located on Lihir Island in PNG, is one of the largest known epithermal gold deposits, with a resource of over 37 million ounces. The deposit is characterised by a telescoped porphyry-epithermal system 2-rich sulphidic hydrothermal fluids capable of transporting significant quantities of gold, and the sudden change from porphyry to pithermal conditions caused by removal of the volcanic edifice. As magmatic ore fluids breached the surface, cool surface waters (seawater and/or meteoric) acted as a diluent. Although no other deposit is known with comparable geological characteristics and size, positive features that may be looked for in exploration for other like-deposits elsewhere include magnetite-rich alkalic volcanic rocks, large carbonate haloes, and presence of phreatomagmatic breccias. New discoveries may be recessive or undercover, due to the quartz-poor nature of the alteration.

Jan 1, 2002

By G J. Harbort, V Lawson, L Reemeyer

The Jameson Cell is a high intensity flotation device, which utilises induced air from the atmosphere. It was developed jointly by Mount Isa Mines and Professor Graeme Jameson of the University of Newcastle in the 1980s. It is proven to generate fine bubbles, in the order of 300 to 500 ¦m, in a high intensity, high shear and compact zone contained in the downcomer. This aerated mixture exits the downcomer into the pulp zone, which is the quiescent mineral and gangue separation zone. A number of Australian base metal flotation circuits feature a reverse flotation stage at the head of the circuit. Testwork and plant operating data has shown that the use of a Jameson Cell in the prefloat cleaner application has further improved prefloat gangue recovery and selectivity. Operation of a Jameson Cell in a carbonaceous/pyrite prefloat cleaner duty at the Mt Isa copper concentrator increased copper recovery and reduced pyrite in the copper concentrate. Testwork at Zinifex Century Zinc Mine showed a decrease in zinc losses by the utilisation of Jameson Cell prefloat cleaner. Appraisal of a Jameson Cell in a scalping role within the Mt Isa Copper Concentrator indicated significant benefits could be achieved.

Jan 1, 2005

By W Uhlmann, U Grnnewald, B Nixdorf

Flooding with surface water is the preferred technique for the abatement of acidification from pyrite oxidation in the lakes of abandoned Lusatian lignite mines. However, water resources of the region are limited and in addition, interruption of water inflow during the summer and the termination of the flooding process after reaching the final water level can lead to a re-acidification of the lakes. The development of three mining lakes with a surface-water flooding history of six to 28 years was analysed û in two lakes on the basis of fortnightly to monthly hydrochemical monitoring data. During summer flooding interruption, the younger lakes showed a decrease in pH from neutral down to pH 4. The degree of the pH decrease depended on the intensity of the groundwater inflow from the overburden dumps and this affected the hypolimnion more than the epilimnion. The third lake was flooded 28 years ago and up to now, interruption of the surface water inflow resulted in re-acidification. These three examples were able to show the benefits and limits of the surface water flooding technique for the abatement of Lusatian mining lake acidification.

Jan 1, 2003

By Guo H

The importance of using disc cutters for rock excavation is reflected by their wide application in hard rock cutting machines such as tunnel boring machines and raise borers. The forces involved in the cutting process are those due mainly to thrust and rolling forces and are greater than that required by cutting picks. An interesting feature of cutting with discs is the formation of surface crushing, surface and sub-surface chipping and primary crack formation. Experimental, as well as analytical, work has been carried out to determine the optimum spacing between the disc cutters to control primary crack orientation. Wedge bit indenters were used to simulate disc cutters. The paper concludes by proposing a new approach to rock excavation by hybrid cutting based on controlling the primary crack Orientation.

Jan 1, 1992

By Z R. Guo, Y Qiu, X F. Wang

Mechanical damage leads to the increase of effective stress of sediments, and pore closure hinders the discharge of methane gas. Ignoring the influence of mechanical damage leads to an excessive prediction of hydrate gas production. Therefore, a fully coupled model considering mechanical damage-chemical decomposition-gas-water two-phase seepage-temperature was developed in this study, and the model was verified by Masuda experiment. Based on the fully coupled model, the temporal and spatial evolution of the whole process of hydrate decomposition under the influence of three initial absolute permeabilities, three pressure drops and three water saturations were considered. The results showed that: • The gas production rate reached the peak value in a short time after depressurisation, and the peak value increased with the increase of the absolute initial permeability. The larger the initial absolute permeability was, the faster the damage variable reached the peak value. The porosity increased gradually before the damage variable reached its peak, and the gas flowed more easily. • When the pressure drop was low, the hydrate remained stable in solid form. As the pressure drop increased, the hydrate gradually began to decompose. The greater the pressure drop was, the faster the initial decomposition rate of the hydrate was. So the damage variable increased rapidly and the porosity increased continuously, resulting in a large gas production rate at the initial stage of decomposition. • The larger the initial water saturation was, the smaller the effective stress wss, resulting in the slow growth of the damage variable and the small change of porosity.While the gas relative permeability was small, it resulted in a smaller gas production rate, and hydrate decomposition was slower. • The damage variable showed a process of rapid growth first, then slowly increased to the peak, and then gradually decreased to a stable state. When the damage was considered, the hydrate decomposition time to the steady state was longer, and the gas production was about 80.68 per cent of that without considering the damage.

Nov 29, 2022

The highland region of Papua-New Guinea is relatively rugged terrain where stream gradients are steep. In areas where porphyry copper deposits outcrop the streams commonly expose primary sulphide mineralization in unoxidized rocks. Stream sediment geochemistry combined with float examination and broad geological mapping proved to be an effective tool for detection of outcropping bodies of mineralization. After discovery, detailed stream sediment sampling, soil sampling and rock chip sampling, together with detailed geological mapping proved adequate to delineate drilling targets. Reconnaissance stream sediment sample density was dictated by geology and access and a density of one sample per 25 Km2, or less, was desirable to ensure a high degree of confidence in the programme. Research indicated that the base metals occur in sulphide form in stream sediment and that the -80 mesh size fraction gave the most reliable results. The evaluation of results from any one area relied on the interpretation of the local geology. Basic histogram methods for determining background and threshold values for metals in stream sediments were

Jan 1, 1973

By Haeussler P, Christie A, Bradley D, Skinner D

Mesothermal gold deposits of southern Alaska and Westland, New Zealand have both formed at the seaward edge of major collisional zones in the Pacific basin. In Alaska, production of large fluid volumes correlates in time with the addition of heat into the lower parts of the accreted terranes in the late stages of collisional orogeny. This heat was critical for driving both the metamorphic reactions that released the large volumes of fluid that carried the gold, and the contemporaneous widespread anatexis and magmatism. In Alaska's Chugach terrane, this heat was produced by subduction of a spreading ridge beneath the North America continental margin in the Eocene. The resulting products were the S-type granites and gold-bearing veins. The similar widespread S-type plutonism and gold veining in Westland's Buller terrane suggest that a similar tectonic event could have triggered ore formation along the southeastern edge of Gondwanaland. Based on the Alaskan model, a Devonian or Early Carboniferous age is favoured for high volume metamorphogenic fluid generation and gold vein formation in Westland.

Jan 1, 1995

New Zealand's Land and Income Tax Act 1954 contains unique incentives for companies engaged in mining certain specified minerals or petroleum. Sections 152 and 153 provide for the taxable income of such companies to be based not on profits made but on dividends paid to shareholders. A significant saving in tax results, particularly where profits are not distributed: but the Act attempts to ensure that undistributed profits are used for further mineral exploration and development. To encourage investment in the mining industry, persons taking up shares in a company mining for the specified minerals or petroleum are entitled to a one-third deduction in respect of monies paid on the shares and used by the company for its purposes; and company shareholders may make loans to the company and write-off such loans for tax purposes to an amount of up to half their taxable income. Maximum utilisation of the tax incentives calls for careful consideration as to whether a mining or petroleum company should be financed by way of loan capital or share capital.

Jan 1, 1971

By B Petrie, D J. MacKenzie

The Macraes mine is producing 175 000 ounces Au/year from a mesothermal deposit with total resource of at least five million ounces. The deposit is hosted in greenschist facies Otago Schist, a widespread Mesozoic metasedimentary sequence that forms the basement of the South Island of New Zealand. Mineralisation was controlled by a late metamorphic shear zone which had both brittle and ductile structures accompanying mineralisation. The shear zone dips shallowly (about 15¦), subparallel to the shallow-dipping regional foliation, and mineralization occurred during southwesterly-directed thrust motion. Mineralisation occurred under greenschist facies conditions (about 350¦C) during uplift of the Otago Schist in the late Jurassic. No syn- or late-metamorphic igneous bodies occur within the schist belt. The hosting shear zone is up to 120 m thick, and is traceable for more than 30 km along strike. The shear zone is truncated by an underlying low angle normal fault that juxtaposes mineralised lower greenschist facies rocks on to unmineralised upper greenschist facies rocks.

Jan 1, 2004

By J-P Franzidis, E V. Manl, K Runge

Over recent years a number of techniques have been developed as part of the Australian Minerals Industries Research Association (AMIRA) P9 project to represent mathematically or measure directly subprocesses occurring in flotation cells. These include the determination of a:machine parameter (bubble surface area flux, Sb); froth parameter (froth recovery, Rf); entrainment and drainage parameters; and ore floatability parameter (Pi). A cost-effective methodology was developed for using these techniques to derive models of flotation circuits. This methodology was applied to derive a model of the flotation circuit at the Western Mining Corporation (WMC) Ltd Mt Keith Nickel Concentrator. The model was used to simulate a number of minor circuit flowsheet changes, the results of which are discussed in this paper. One year later, a second study of this plant was conducted. In this second study, data were collected while operating the plant in the flowsheet configurations that were simulated from the model developed from the first study. The results obtained from the second study showed reasonable agreement with the trends predicted from the first study model; discrepancies can be explained in terms of the model assumptions. This suggests that this simple circuit modelling methodology can be useful in assisting plant engineers to optimise flotation circuits.

Jan 1, 2000

Oceana Gold CorporationÆs (OGC) Frasers underground (FRUG) transitioned into production in early 2008. The mine uses a relatively unique yielding pillars mining method that takes its lessons from empirical coal mining practices more so than hard rock techniques. Being a low-grade, flat-dipping resource hosted in the highly structured relatively weak Otago schist in central South Island in New Zealand, meant a number of iterations were undertaken to find the right mix of mining cost and resource extraction. Mining is on the down dip extension of the active Frasers open pit at the Macraes site (that extracts the full shear zone package at a head grade of 1.5 g/t). The challenges for the FRUG feasibility study team was to deliver an net present value (NPV) positive operation that would exist as a coproduct with OGCÆs other New Zealand operations, allowing it to make use of the high throughput low cost refractory ore treatment facility.Key factors in the successful project design were: Net capital costs kept to less than NZ$30 M by realising significant gold revenues from mine development from month four onwards. Virtually eliminating waste development by putting all key capital infrastructure in the low-grade ore adjacent to panels and maintaining the option of extracting this resource on retreat from the mine. Targeting a specific higher grade halo ore package within the entire mineralised shear zone. Applying a mining method that accepted a higher degree of dilution, ore loss and resource loss (in yielding and non-yielding pillars) to the flat-dipping resource. Thus providing an acceptable margin per tonne and resource tonnes mix, as the resource could not support a conventional low-cost caving operation, nor a higher cost room and pillar or open stope and backfill operation. 2008 has seen increasing tonnes and grade performance with a corresponding decrease in cost per tonne and cost per ounce as the mine has reached nominal capacity and is producing an operating surplus. The challenge will be to maintain and improve.

Jan 1, 2009

By Restarick CJ

Plant data are presented which indicate a relationship between flotation rate constants and pulp density in zinc cleaning circuits at Broken Hill. The data were obtained from down the bank sampling of cleaner and recleaner banks at North Broken Hill and New Broken Hill Consolidated Concentrators. It was found that, under normal plant operation, flotation rate constants increased at the lower pulp densities existing in the later cells of cleaner banks. The addition of dilution water to the feed to the bank increased flotation rate constants, thereby confirming the relationship. It is shown that the relationship between flotation rate constant and pulp density is size dependent, being most pronounced for larger sized particles. In contrast, the effect is not markedly dependent upon mineral type. Possible consequences of this relationship for control of cleaner operation are discussed with the aid of some simulated results.

Jan 1, 1978

The Nagambie heap leach gold mine commenced production of gold in September, 1989. The mine,120km north of Melbourne in Victoria, Australia, was developed by Perseverance Mining Cor- poration Ltd, a junior Australian mining company, with no other operating mines. Gold production to December 31, 1990 was 47,621 oz. The mine is now producing at the rate of about 45,000 oz per year. As of February 28, 1991, resources at the mine are 5.1 million tonnes measured, at 0.65g/t Au while reserves were 1.65 million tonnes at 0.86g/t Au of proven, heap leach ore, plus 0.37 million tonnes at 0.40g/t Au, of dump leach ore. Metallurgical recoveries expected are 80 per cent for the heap ore and 60 per cent for the dump ore. Perseverance Mining Corporation was listed on the Australian Stock Exchange on April 2, 1987, after a capital raising in March that year. At this time the company's issued capital was 4 million ordinary 25ó shares, 3 million of which were issued to the public to raise $0.75 million.

Jan 1, 1991

By Thorburn D

This paper reviews the history of environmental assessment in New Zealand with reference to mineral developments. Emphasis is given to larger more controversial projects particularly metal mines. The changing role and application of the Environmental Protection and Enhancement Procedures is examined in the context of changes in the government's environmental administration and the response of the Ministry of Energy's resource allocation group. Conclusions are drawn on the effectiveness of the present environmental assessment activities and on the allocation of administration of priorities in the Ministry. The Ministry of Energy has effectively ceased to exist.

Jan 1, 1990