Search Documents

By Porter I

Rock mass classification systems have emerged as a powerful tool which can be used for assessing ground conditions and determining support requirements in underground mines. They should not be used as a substitute for complete engineering design, but rather as a supplement to observational methods and analytical study. In general, the use of rock mass classification is attractive, but each classification system has various deficiencies. Use of any particular system should be made only with knowledge of that systems limitations. It is desirable to employ a number of systems and design methods which will allow for comparison and lead to a better understanding of the rock mass condition.The Rock Mass Quality system (Q-System), developed by the Norwegian Geotechnical Institute, and the Rock Mass Rating (RMR) System, Bieniawski, were designed primarily for civil engineering structures. Laubscher et al (1978) further developed the RMR-system specifically for rock mechanics engineering in the mining industry. A method of stope design, which introduces a stability factor for the rock mass and compares this with hydraulic radius, was developed by Mathews et al (1981). This paper reviews the above systems by applying them to stability assessment of crown pillars in two Australian metal mines and provides a critical analysis of the various approaches. In particular each system will be analysed to determine its suitability for use in crown pillar design. The most suitable system(s) will form the basis for future development in crown pillar stability analysis.

Jan 1, 1994

By Sobek S, Lotzien RM

Although the conventional procedures for designing agitator flotation plants are well-known and reliable, little experience for designing modem pneumatic flotation plants has been gained up to now. A reliable procedure originating from graphic methods for the design of distillation columns is presented. Examples demonstrate on laboratory and semi-technical scale the application of this extremely practical method for designing a fly ash and a magnesite flotation plant.

Jan 1, 1993

By Xizhen J

Point load testing for irregular rock specimens was studied to determine the relationship between tensile and compressive strengths, drill penetration rate and other rotary drilling parameters. The DH-l type point load tester was developed and more than 2 000 irregular specimens of over 60 kinds of rock from 16 mines and quarries were tested. The effects of size, shape and number of samples on the point load strength index were investigated, using regression analysis. Experiments were carried out to investigate the relationship between point load strength index and uniaxial compressive strength on 29 kinds of rock. The relationship between these values and the drill penetration rate for rotary and percussion drills is discussed.

Jan 1, 1986

Access roads for haulage, construction or maintenance purposes are discussed with particular attention being given to the un- sealed "all weather" form of construction for Off-Highway applications. The service conditions experienced by the surfaces used in these roads is examined. These conditions are discussed in terms of the conventional engineering properties used for natural gravel material selection. Experience gained during the construction of a pipeline access track is used to illustratE material selection guidelines based on geological input and an understanding of good construction practices. TMITDnIll IrTT Ohl In many Australian situations off-highway haulage by wheel or track supported vehicles is carried on unsealed, gravel roads. Although the unsealed gravel road is the back-bone of the rural road network in Australia, in general, traffic loadings are relatively low compared to the off-highway unsealed haulage road. The cost of the haulage/access road construction component is one important factor in project planning which needs careful consideration. It is no longer acceptable that the initial rough exploration track be gradually upgraded so that it will eventually carry construction and maintenance traffic safely and efficiently. Fatal accidents and

Jan 1, 1982

By P N. Holtham

Magnetic separation is routinely used in the processing of titanium minerals, and the efficiency of these operations can be determined by measuring the magnetic properties of the process streams. The valuable components in the feed to a titanium minerals plant have specific magnetic susceptibilities ranging from -10-9 m3 kg-1 (zircon) to 10-6 m3 kg-1 (ilmenite). However, in an industrial environment, in which the mineral temperature may range from 20 to 120¦C, it is difficult to measure susceptibilities lower than about 10-7 m3 kg-1. Hence laboratory testing of spot samples from magnetic separators is currently required to obtain accurate performance data. This is an inherently slow process and where feed grades are variable, optimum performance of magnetic separators is generally not achieved. This paper describes the development of an inductance-based instrument for measuring very low levels of magnetic susceptibility on-line. The signal from the instrument can be used for process control purposes to maintain optimum magnetic separator performance. A prototype instrument has been installed in the zircon scavenger circuit in an Australian titanium minerals plant. The circuit consists of a roll magnetic separator treating a feed consisting mainly of monazite and stained zircon. The monazite-rich magnetic fraction is returned to the mine site for disposal, while the non-magnetic fraction is recycled to the zircon wet circuit. Splitter positions in the separator are adjusted when the final zircon product fails to meet specification, or the magnetic fraction contains more than 30 per cent zircon. Weekly composite grain counts show that sub-optimal operation of the magnetic separator results in significant zircon losses into the magnetics fraction. Using the instrument, the zircon content of this stream can now be accurately determined from the measured magnetic susceptibility, provided a correction for the effect of mineral temperature is applied using the Curie - Weiss relationship.

Jan 1, 2001

The provision of electrical power is an important consideration in project development. The first step to be taken in this area is to assess the power requirements of the project. The alternatives of laking a supply from a power authority or providing local generation can then be considered. This requires additional defmition of the probable characteristics of the supply.The availability of authority power in Australia is limited by the extent of the state power grids. Recent developments now allow these grids to be extended and their load capacity increased to meet major load increases at less cost than was previously possible.The options for local generation include diesel, gas turbine, steam, hydro, solar and wind, each having its particular performance characteristics and costs. The choice of fuel for diesel, gas turbine, and steam plant likewise involves consideration of a range of factors. The arrangements adopted for five recent Australian remote development projects indicate how some of these aspects influence the decision on power supply.

Jan 1, 1990

By Brien R. J, O&apos

Faster and more efficient methods of producing and refining iron and steel are imposing severe conditions on the refractory materials used to contain these metals in the molten state. In order to provide refractory linings which will give the desired service life and maintain unit availability at an economical level, it is necessary to appreciate the aggressive environment in which the refractories operate and determine the reaction mechanisms by which the refractories are destroyed. Only by such studies can the most suitable refractory or refractory combination for a particular unit be selected. Examples of refractories selection and reaction mechanisms are discussed for blast furnaces, BOS vessels, AOD vessels, steel ladles, vacuum degassing units and continuous casting.

Jan 1, 1976

By Seedsman RW, Duncan Fama ME

Mine design procedures will be revolu- tionised by technological developments in computers, software, database construction and management, and numerical modelling programs. Developments in geotechnical databases will be required which utilize geological and geomechanical tests to supply appropriate input for numerical models. Techniques utilizing sedimentological and structural modelling are described. The capacity of current numerical models in mine design is outlined and a program for developing a fully integrated mine design package proposed.

Jan 1, 1987

Various factors influence the exploration geologist or geochemist in his choice of.an analytical method for gold and other elements which may help him find the elusive gold deposit. One of the first decisions the geologist must make is the nature of sample media to collect for his survey. Needless to say there are many media available depending on the situation. These include rocks, soils, heavy mineral concentrates (from overburden drilling and panned concentrates), humus, vegetation, water, lake bottom sediments, stream sediments, etc. The choice of the sample media will depend to a large degree on the state of development of the particular project from grassroots to mine feasibility. The nature of the geological information required will affect which media and which analytical technique should be chosen for the analysis. Valid sampling from the initial sample collection, preparation and subsampling aspects may also help to determine which analytical procedure is best. Cost and turnaround time are of prime. importance to the explorationist, as it should be, however, these aspects should not be detached from receiving accurate and reliable results.

Jan 1, 1987

The treatment of nickel ores and concentrates and the subsequent processing to recover separate products of nickel and cobalt is one of the major interests at present in the mining industry. The increasing demand for nickel, and more recently also cobalt, has led to increased exploration for ore sources. Major discoveries have resulted in Canada and Australia. These deposits, as well as others already known, are presently being developed and the process technology tested and evaluated for applicability to the different mineralogical types - mainly sulphide, arsenide and oxide laterites. Concentrates may be treated by either hydro- or pyrometallurgical processes, while the nickel laterites are best suited to hydrometallurgical processing. However, if hydrometallurgy is used, once the ore or concentrate is leached the resultant solutions are then amenable to similar separation technologies for purification and recovery of high purity nickel and cobalt products. Solvent extraction, together with other separation processes such as precipitation, can produce high purity solutions of nickel and cobalt. The final products of these solutions may be nickel and cobalt cathodes, metal powders precipitates or salts, depending on the final process of electrowinning, hydrogen reduction, precipitation, or crystallisation Respectively.

Jan 1, 1996

Conflicting claims and views on the priming of ammonium nitrate/fuel oil (ANFO) are reviewed; certain fallacies and misconceptions are rectified. Optimum priming systems for a range of blasthole conditions are indicated. Moves towards optimum priming lead to reductions in the combined cost of drilling, blasting and handling the material. With shallow blastholes, two-point priming is rarely warranted. Best blasting results from single priming are usually obtained when the primer is located near, but not at, the bottom of the blasthole. As blast- hole depth increases, two-point priming becomes more reliable and effective than single priming. For two-point priming, primers should be located such that detonation waves in the ANFO collide at grade level or, if preferred, within a hard band in the burden. Where blastholes are very deep and/or strata variations can be appreciable, three or more spaced primers are often justified. The effectiveness of a primer varies with its detonation pressure, diameter and length. Primer properties influence the velocity of detonation (VOD) near the primer, but do not affect the final (steady-state) VOD in the ANFO. Some primers cause 'run-up' (i.e. lower than steady-state) velocities whereas others cause

Jan 1, 1974

The establishment of vegetation onto open cut mine spoil is dependant on the nature of the soil and rock strata of the overburden. Experience has shown that in the Bowen Basin of Central Queensland the nature of the minespoil changes considerably as subsequent and deeper mining strips intercept changing rock strata. The different mixes of strata at the surface of reshaped spoilpiles can produce variable response in the sown vegetation cover. It is usual that land features of mine sites are known in detail and are depicted on mine or locality maps. Subsurface strata and lithology descriptions are available and are used for planning of open cut mining operations. Surface and subsurface data can also be used to estimate the intrinsic nature of overburden through the use of fence diagrams. Lithology at points along a mined strip can be obtained and used to describe overburden. Indications are that correlations exist between salinity of overburden components and the response of vegetation. The developed procedure thus becomes a useful tool for the prediction of revegetation Practices.

Jan 1, 1987

The energy input requirement to produce the molten slag associated with iron production to the modern Australian blast furnace, is estimated to be 2.OMJ/kg. In converting blast furnace slag to products of higher commercial value, advantage should be taken of this energy content by transporting molten slag from the furnace for beneficiation and processing in the molten state at an "off furnace site". The refined slag melt may then be converted into a variety of products for use in the building and construction industries, e.g. slag cement, slag sand and slag aggregates, insulation wool and various slag ceramic products. Some results of studies into slag melt beneficiation and conversion processes involving both molten and cold granular slag raw material, are presented.

Jan 1, 1979

By N Stockton

Some preliminary results on the secondary leaching of previously heap leached gold ore are presented. Alternative lixiviants for gold comprising chlorine, thiourea and thiosulphate were compared with cyanide using bottle roll tests. Chlorine was subsequently selected for column leaching tests. Column tests at 1.0, 0.1 and 0.01 gL-1 Cl2 at pH 2 were conducted. The results indicated that about 23 per cent of the gold was leached over 45 days using 1 gL-1 Cl2 at pH 2. The experiments conducted proved that the chlorine/chloride system has good potential for further extraction of gold and silver from the existing cyanide heap leach residues and a process for secondary leaching of gold has been proposed. Further testwork is recommended to extend conditions, sample types, and the duration of leaching period.

Jan 1, 2000

This paper describes the principle of cut-and-break rock excavation, in which rock is first undercut, and the undercut material is subsequently broken free by a wedging action. The current work on cut-and-break using the large rock cutting test rig at the Centre for Mining Technology and Equipment (CMTE) is outlined, and suggestions are made as to the potential advantages of cut-and-break roadheading, particularly in excavating short tunnels in hard rock in an urban environment.

Jan 1, 1993

Recent operating experience from West Australian open pit gold mines has shown that geotechnical input into initial design is rare. As a result, ground stability is poor - almost half the pits designed in this way suffer major failure.West Australian experience shows that geotechnical studies for individual mines are site specific, and therefore empirical experience cannot be transported from site to site. Geotechnical studies performed prior to design have resulted in significantly improved pit stability.

Jan 1, 1990

By J L. Merritt

Effective minesite water management requires that this issue be treated as a risk management exercise. The management process is generally far from simple and by necessity must involve a range of personnel covering a siteÆs commercial, operational and environmental interests and responsibilities. The challenge to be collectively faced by these stakeholders is to strike the correct balance between risk and cost. On the other hand, the challenge to be faced by technical services support personnel is to provide stakeholders with information in a format that they can use with confidence. This paper presents the application of continuous operational simulation (OPSIM) modelling techniques to establish appropriate risk profiles for minesite operations. It is necessary that the format of these risk profiles be generic and equally applicable for defining the risk of occurrence for a relatively comprehensive range of activities û eg from of a non-compliant discharge, to the risk of failure to meet production targets. What is more, the profiles need to be quantitatively based and capable of reflecting change in system response to varied operational or management strategies. The techniques presented in this paper are based around a key assumption that long-term records of the climate contain within them sets of sequences that are representative of what can be expected in the future û that is, the droughts, floods, cyclones, good years and bad, long or short, and everything in between. Therefore, if these historical records are run through an OPSIM model for a particular site, then the simulated operational characteristics can be taken as being representative of what can be expected in the future, in the long-term. This lends itself to statistical analysis and translation into the required risk based format. Water Solutions Pty Ltd have been working with Capricorn Coal Management to develop a relatively comprehensive OPSIM model of their operations at German Creek Mine, Central Queensland. Outcomes from the modelling have been used in recent times to provide mine management with risk-based guidelines for both securing and containing mine water inventories. One of the more interesting tasks has been to establish risk based inventory levels that, if reached, would trigger the immediate implementation of a contract for the desalination and re-use of mine water, at predefined rates. Also, lead-time warning of the occurrence of a possible trigger is of importance to operational and commercial planning. To service this requirement the OPSIM model is regularly used to produce lead-time estimates to defined levels of confidence. Case studies of these, and other, applications of the OPSIM model at German Creek Mine are presented in this paper and serve to demonstrate an effective methodology for practical risked based water management.

Jan 1, 2003

The need to estimate the block size distribution of a jointed rock mass is of great importance in the design of blasting rounds to attain a pre- established fragmentation. Other Geomechanics topics, such as ,hydraulic behavior of rock-masses, as well as the determination of their strength properties, also require the accurate prediction of a rock-mass composition in terms of block size taking in due account the three dimensional interference of joints and other geologic discontinuities. In this paper, a method for computing the block size analysis of a jointed rock mass is described, using as input the common geologic data (dip and strike) of fracture planes existing in a rock bench prior to blasting.

Jan 1, 1977

By Dorricott M. G

Rock bolt installation is generally carried out in two steps. First the hole is drilled and the drill steel is extracted, then the bolt is inserted into the hole and tightened or grouted. With single pass bolting (SPB), however, these two steps can be carried out at the same time. This kind of bolting system has at least three advantages, (1) the time used for the bolt installation could be reduced, (2) the condition of safety for the operators could be improved, and (3) the degree of automation of the rock bolting practice could be increased. The study presented in this paper is concerned with the development of the SPB system. The current state of the system is discussed, and further improvement of the technique is explored.

Jan 1, 1992

By Hutchinson IN

In order for the Australian underground coal mining industry to achieve the high productivity rates demanded of it without compromising its good safety record, improved geotechnical monitoring systems are required. One of the main problem areas affecting underground coal mining is the deterioration of previously stable roadways.CSIRO Division of Geomechanics has been working on a NERDDC funded project to develop an instrument to monitor coal mine roof deformation. The instrument which has been developed, Roof Alert, is a self contained, battery powered, intrinsically safe device. It can monitor the magnitude and rate of deformation and give multiple, variable visual alarm signals where preset levels ate exceeded.

Jan 1, 1991