Search Documents

By N Johansson, D Johansson, A Beyglou, H Schunnesson

As demand for optimisation of mining processes increases, more attention is drawn to blast performance and fragmentation improvement. Fractures and discontinuities are among the most influential factors in blast results, therefore one of the initial steps towards blast optimisation is to gather information about the rock mass and integrate it in blast design. This paper presents a method for assessment of rock mass discontinuities and integrating it in production blasts in the Aitik open pit copper mine in Sweden.3D photogrammetric techniques were utilised to map discontinuities and distinguish domains of similar geologic structures in the pit. As a pilot study for a future campaign, four different initiation directions were tested through six pilot blasts in one of the domains. The results were compared in terms of swell and loading efficiency of rope shovels to identify the correlation between blast performance and initiation direction compared to major discontinuity families.It was established that in the trial domain, blasts initiated towards north or north-west yielded larger swell and better performance of loading. Comparing these blasts with discontinuity families show that there is a correlation between blast performance and initiation direction according to the dip and strike of these discontinuities. Such knowledge can be used for future blasts in the same domain to increase long-term operational efficiency through slight modifications in drill pattern and initiation design.CITATION:Beyglou, A, Schunnesson, H, Johansson, D and Johansson, N, 2015. Adjusting initiation direction to domains of rock mass discontinuities in Aitik open pit mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 385–392 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By J Webb

Anoxic limestone drains (ALDs) have been widely used in the passive treatment of acid mine drainage (AMD), but their effectiveness has often been less than anticipated. Iron hydroxide often precipitates around limestone particles and inhibits neutralisation. To determine the conditions under which iron hydroxide precipitates, a small-scale laboratory ALD system was built to enable a detailed examination of the chemistry of iron within the drain. For one experiment, a mixture of limestone and quartz was introduced to the drain to assist in the determination of the key mechanism governing iron precipitation. Synthetic anaerobic acid mine drainage containing Fe2+ (~130 ppm), SO4 2- and H+ was pumped at a rate of 30 mL/min up a 90 cm tall, 15 cm diameter vertical column filled with limestone gravel of 98 per cent purity. Three sampling ports were fitted at equal intervals along the column; water was periodically extracted for analysis at the sampling ports over an 11-hour period. Experiments were run at influent pH levels of 2 and 4. Results show that acid neutralisation to pH greater than 6 occurred at the inflow end of the drain. The greatest amount of iron precipitation (19.5 per cent) also occurred in this area. The lack of iron precipitation on the quartz surfaces in the quartz/limestone mixture indicates that neutralisation is the key mechanism for the precipitation of iron hydroxide on limestone particles. A pe-pH stability diagram derived for the laboratory ALD system indicates that ALDs will not be effective for AMD with pH 2. Influent waters with pH 2 require a pe of -2 (Eh: -118.4 mV) to avoid Fe precipitation upon neutralisation. Influent waters of pH 4 require a pe between -2 and -4.

Jan 1, 2003

By E J. Hill, F Huang, A Otto

Geochemical data from drill core samples is used in mineral exploration to enable geologists to understand subsurface geology. However, it is challenging to analyse these data sets rigorously and consistently. Manual data interpretation relies on the knowledge and experience of logging geologists. When multiple geologists are involved, it is possible to introduce inconsistencies in logged lithology type and scale of logging (‘splitters’ versus ‘lumpers’). Machine learning (ML) is a powerful tool for analysing high dimensional data (ie data with many variables) and large data sets (ie data with many samples). However, ML methods applied to drill hole samples do not incorporate spatial information and this can result in high misclassification rates and small-scale ‘noisy’ results. We demonstrate the use of multiscale spatial analysis (wavelet tessellation) as a pre-ML step to analyse spatial information. This step helps reduce misclassification and filter out unwanted small-scale variation in the data. In an experiment, we used wavelet tessellation and supervised ML to predict litho-geochemical rock types from geochemistry data. The data set is from the Valhalla uranium deposit near Mount Isa, northern Queensland. First, geochemical knowledge and statistical analysis was used to select appropriate geochemical elements for litho-geochemical classification. Second, the elements were processed using multiscale spatial analysis. Third, we trained a Random Forest model with the data set and found that the model performs worse in predicting rare rock samples than common ones. We applied over-sampling and down-sampling methods in aim to overcome this issue. As a conclusion, the combination of multiscale spatial analysis (to define rock unit boundaries) and Random Forests (to classify rock units) is a good method for rapid and accurate analysis of drill hole geochemistry.

Mar 22, 2022

By J Rutter, D La Rosa, P Walters, M Scott, L Keeney

Bulk ore sorting technologies, whether surfaced based or penetrative, have seen an increased uptake by the mining industry for preconcentration application. As with all technologies, going through the technology validation process is key to de-risking the operationalisation of the technologies and to demonstrate and confirm predicted value propositions. The ability to laboratory calibrate cross-belt bulk sensors is standard practise for sensor vendors, however transitioning the technology from laboratory to real-world application is a non-trivial process. The industry has taken two main approaches to trialling and validating bulk sensing technologies in operational environments, namely:  Construct an off-line pilot facility at scale, or  Install bulk sensing systems on production conveyors Each of these two approaches have significant advantages and disadvantages and require different experimental design programs and analysis methodologies. Consideration of material movement, heterogeneity degradation, logistical requirements, and financial investment all factor into which approach is most suitable for an evaluation scenario. CRC ORE in partnership with mining companies, have conducted several bulk sensor pilot trials utilising different sensor technologies employing each of the two main approaches outlined above. This paper describes the challenges faced, learnings obtained and outlines a position on how to transition bulk sensing technologies from the laboratory into the operating environment. The case studies presented cover a range of commodity types in both open pit and underground operations.

Nov 10, 2020

By J E. Powalisz

"The application of automated sampling techniques can help to provide a representative sample of process fluids and slurries that provide data for controlling process, custody transfer and quality assurance and quality control purposes.The automation of sampling provides a more consistent and reliable sampling process and eliminates many of the human-induced errors. Automated sampling can also provide a higher degree of safety in the plant/processing environment as well as better bottom-line results.Automated, fixed volume samplers can provide a very representative sample by integrating many small ‘grabs’ of sample from a process. Automated samplers can be controlled in a variety of ways to optimise the sampling process, including:cycle ratedwell timetotal volume.Properly selected and applied, an automated sampler can effectively isolate the operator from the process fluid during sampling and, to a great degree, during sample container collection.A variety of materials of construction, including seals, are available to handle demanding mining applications. Alloy 625, alloy 2205, AL6XN® and even certain plastics are used successfully in mining slurry applications.This paper explores the application of automated, fixed volume, batch style samplers in copper/nickel and gold processing, specifically pregnant leach solution and extraction fluids.Several specific field applications are discussed, including process installation details, hardware and operation.CITATION:Powalisz, J E, 2014. The application of automated samplers in copper/nickel processing, in Proceedings Sampling 2014, pp 35–42 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 29, 2014

The efficient design of carbon-in-pulp (C.I.P.) plants involves the integration of both process engineering and design engineering.Many recently constructed plants have not recognised the above interrelationship, and as such have incurred higher capital and operating costs than were in reality necessary. This has been compounded in some cases by slavishly following the design of plants where process conditions are different for the ore characteristics in question, thus perpetuating design errors that finally become industry "accepted practice".In the paper that is to be presented the unit operations of crushing, grinding, classification, leaching, adsorption, desorption and electrowinning in C.I.P. plants will be discussed with reference to the integration of process and design engineering.

Jan 1, 1986

By B Chapman, B Gaida, L Drowley

The 372 MW Ulu Jelai Hydroelectric Project is a peaking power scheme located in the Cameron Highlands, Malaysia. The main features of the project include an 84 m high roller compacted concrete dam; two weirs which divert flows from adjacent catchments via transfer tunnels into the main reservoir; an underground power waterway; and an underground power station complex comprising three large caverns with connecting tunnels approximately 240 m below surface level. The project includes approximately 25 km of tunnels excavated in fresh granite rock mass with some distinct shear zones of weaker material. The majority of the tunnels are being excavated using drill and blast, with the two transfer tunnels being excavated with a tunnel boring machine (TBM).This paper focuses on the design and construction of the Telanok underground power station complex and also some aspects of the design for the headrace tunnel. Topics covered include geological site investigations including in situ measurements of rock stresses; development of a geological model and parameters for rock support design; three-dimensional modelling to assess interactions between the caverns to optimise rock support; design of a rock anchored crane beam; construction of the caverns and design of the unlined headrace tunnel taking into account hydraulic jacking and operational pressure fluctuations.CITATION:Drowley, L, Gaida, B and Chapman, B, 2014. Design and construction of large caverns in granite – Ulu Jelai Hydroelectric Project, Malaysia, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 361–368 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By C Artica

Two quantitative methods for Mineral Resource classification have been applied to a copper skarn deposit beneath a large open pit that is mining a world-class porphyry complex. A drill hole spacing study (DHSS) using the single block kriging method (SBK) and a conditional simulation method (CS) were applied to the skarn deposit and the results compared. Inputs to both processes included the proposed mining rate and stope designs to estimate the likelihood of achieving grade and metal production targets. Mineral Resource classification of the deposit considers the relative precision of tons, grade and metal predictions over quarterly and annual production periods. These relative precision estimates are calculated at 90 per cent confidence interval (CI). The SBK method represented the production period as a single large block. Kriging estimates were performed in the large block for various synthetic drill hole grids, and the estimation errors derived. The error was assumed to be normally distributed due to the large block size and quantity of samples, allowing CIs to be deduced. The CS method followed a conventional sequential Gaussian simulation workflow where grades were simulated with a 5 ft × 5 ft × 5 ft grid node spacing inside mineralisation domains. Each realisation was then averaged up to monthly production volumes represented by a combination of designed stopes, and the coefficient of variation (CV) for the averaged grade was calculated. CI on the relative precision of grade predictions were then deduced from the CVs. The two methods produced similar results; despite being calculated independently. CS results were used to report uncertainty in the proposed life-of-mine plan and highlight areas for additional drilling. SBK results were used as the basis for Mineral Resource classification as this method has been previously applied to the skarn deposit.

May 24, 2023

By Murdaugh W

The application of photogeological techniques and analysis of more advanced remote sensor images can be a cost and time effective tool in the search for desert placer gold deposits. Examples are given of regional analysis using standard false color composit Landsat images and conventional black and white aerial photography. The examples include identification of sites to sample to evaluate the pathways of .alluvial gold migration and identification of potential sites of concentration. The results of these studies developed an increased number of target areas and exploration in proceeding with promising results. In addition to the development of additional target concepts and identification of specific target areas data useful to evaluation of mineability can also be obtained from photogeological investigation. Some indication at least can be obtained of the existence of duricrusts and salines that may hamper mining. Identification of possible sources of water is another important task in the desert environment. In addition indications of the clay content of the material to be worked is very important because of its economic impact on operational costs and overall recovery. The application of photogeology to these questions is discussed.

Jan 1, 1988

By A Manfrino

The Iron Bridge magnetite mine and infrastructure project is currently in development as a joint venture between Fortescue Metals Group, Formosa and Baosteel. It is supported by an extensive database of reverse circulation drill hole samples analysed by X-ray fluorescence (XRF), with a large subset tested for concentrate mass recovery, concentrate and tail grades by Davis tube recovery (DTR) testing. A limited number of rock physical testing results, including unconfined/uniaxial compressive strength and crushing work index, completes the database.By combining all available information – assays, DTR results, geology, stratigraphy, mineralogy and rock physical results – and using multivariate statistical analysis techniques, the impact of the critical factors that control concentrate quality, mass recovery and grindability characteristics have been outlined. A set of geochemical groups was created by using a cluster analysis technique from the combined XRF-DTR data. These groups allow optimal separation of material with consistently high concentrate Fe grades and mass recovery. This approach is superior to domaining based on stratigraphic logging or mass recovery as it is commonly used in standard magnetite estimation models. Using the results of a normative mineralogy study, the main geochemical groups were given a mineralogical profile fitting their geochemical characteristics. These findings further refined the understanding of the link between the process characteristics of the samples and their geochemical signature and mineralogy.The geochemical grouping defined on head grades and DTR concentrate mass recovery was generalised into a ‘geomet’ code based solely on the routinely assayed head grades, thus bypassing the need for systematic DTR testing. The geomet code identifies spatial domains with homogeneous geochemistry, mineralogy and process characteristics in both oxide and fresh material that form the basis of the current Iron Bridge resource model. The allocation of geometallurgical characteristics in terms of concentration amenability and concentrate characteristics on a block-by-block basis over the whole project allows for an optimum mine schedule and plant feed. This ensures that the desired concentrate characteristics and mass recovery can be better predicted over the life-of-mine, thereby improving the mine’s economics and stability by derisking the mine schedule and optimising the performance of the concentrators. A key benefit of the geomet code devised for the Iron Bridge mine is that it can be attributed in an automated manner to all samples analysed for a routine XRF analytical suite, from exploration to blasthole drilling. This allows each sample to be allocated to a geometallurgical material type with predictable process response in terms of concentrate mass recovery and concentrate quality without the need to complete systematic DTR testing.A standard multivariate analysis coupled with a cluster analysis has allowed the linking of interdisciplinary results between geology, mineralogy, geochemistry, process and metallurgy to better understand, predict and ultimately mine and process the Iron Bridge deposits. This allows plant operations and product quality to be optimised through each stage thanks to the predictable ore characteristics embedded in the mining model.CITATION:Manfrino, A, 2015. Unravelling the factors impacting on concentrate quality by geometallurgical data analysis at Fortescue Metals Group’s Iron Bridge magnetite mine, in Proceedings Iron Ore 2015, pp 567–578 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By B T. Qin, C Zhu, Y W. Jia, Y Lu, F L. Li, Q L. Shi

Air leakage through rock fractures in coal mining is a major cause of coal spontaneous combustion. In order to overcome the deficiency of the existing fire control technology and prevent coal spontaneous combustion by isolating coal from oxygen, the article proposes a novel technology of inorganic solidified foam (ISF) with high expansion to fill fractures effectively. ISF consists of fly ash, cement, setting accelerator, redispersible polymer powder, water and aqueous foam. For preparing homogeneous and stable ISF, a preparation system with a pore type foam generator, a mixer device installed with a hollow shaft and helical blades, air compressor, slush pump and monitoring instruments was developed, and the working principles of key devices were elucidated. Based on a series of experiments on the different ratios of each component material and technological parameters of the preparation system, ISF with a foam expansion ratio of 8~10 and dry density of 250–400 kg/m3 was prepared. The relationship between elastic compressive strength, modulus of elasticity and density was summarised. Based on the injection experiment for fracture of loose coal pile with high temperature, the characteristics of sealing air leakage, compressive strength, thermal insulation, flow and cooling of ISF in the fresh state were investigated, indicating that ISF can effectively cut off the air leakage and cover the coal sample to reduce the temperature in the earlier stage, and ISF can remain stable and not crack. The ISF was applied to Luwa coalmine to seal small coal pillar pressure fractures and loose coal fractures in goaf. After press-casting the ISF in Luwa coalmine, the pressure-difference of inner-outer increased, meaning the effect of external conditions on the pressure-difference decreased, showing that it could plug the air leakage effectively.CITATION:Qin, B T, Shi, Q L, Lu, Y, Zhu, C, Li, F L and Jia, Y W, 2015. The novel technology of inorganic solidified foam with high expansion for preventing coal spontaneous combustion, in Proceedings The Australian Mine Ventilation Conference, pp 121–126 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By Singh RN

The Bulli Coal Seam, located in the Illawarra Coalfield of New South Wales, has a long and varied history of sudden outbursts. From available information this problem has resulted in twelve fatalities over the last one hundred and one years, with over five hundred separate outburst incidents being identified. These incidents have varied in severity and intensity from the discharge of 1 to 2 tonne of coal, with a slight increase in gas emission, to the discharge of 200 to 400 tonne of coal with some 6,000 m3 of gas being liberated and large items of mining equipment being pushed 1 to 2 metres down the roadway.Geological features associated with these outbursts can be mapped on a regional and mine by mine basis, to provide some indication or warning. Similarly changes in gas content and gas composition can also be determined on a regional and mine by mine basis. However sudden geological changes (such as a 6.5 metre seam displacement within 15 metres) variations in gas content (such as 6 m3/tonne to 15 m3/tonne) and changes in gas composition (from 95% CH4 to 90% CO2) all within one mine does make the prediction or forecasting of outburst incidents exceedingly difficult.

Jan 1, 1998

By R Talebi

A research project to better understand the rock mass behaviour and the seismic response has been conducted during the design and construction of the 9215 level at the E-Block sector of the Northern Star Kanowna Belle Mine. The research program was undertaken at a tunnel located 1100 m below the surface with the results applicable to feasibility studies on underground mining projects in highstress conditions, where failure can occur very soon after tunnel construction. Semi-circular excavation shapes coupled with the use of de-stress blasting techniques were designed to monitor the excavation in conditions of very high stress. The ground support was designed considering high energy dissipation ground support schemes (HED) as described by Arcaro et al (2021). The results indicate a decreased rock mass demand due to the change of excavation shape. Also, localised reduction in rock mass stiffness was achieved due to the implementation of de-stress blasting. Finally, increased ground support capacity was gained by the implementation of the high energy dissipation ground support schemes. The Kanowna Belle Mine has significant ore reserves at depths exceeding 1000 m below the surface. The results of this research will be used to optimise the extraction of the remaining E Stoping Block at depths exceeding 1350 m.

Mar 29, 2023

Open pit mining at Bingham Canyon commenced in 1904 and about two billion tonnes of ore have been extracted since then. There remain just under one billion tonnes of ore in the pit and this will be mined by 2015. Because the porphyry system extends below the ultimate pit limits, Kennecott Utah Copper Corporation initiated a study in 1997 to determine the viability of underground mining. The study was initiated at that time because the results were to be used to compare the economics of a further pit expansion to that of an underground mine. If a pit expansion was viable then overburden removal would have to start in the near future. This paper is a summary of the work that was carried out for the underground study. Block cave mining was determined to be the most appropriate method to mine the deposit. Two block cave areas have been planned with a total production rate of 72 500 tpd. Additional sources of ore will come from skarn orebodies that are associated with the porphyry deposit. The geology of the deposits is described together with the geotechnical techniques that were used to characterise the rock in the absence of more detailed data that are normally available. A general description of the mine plan is given along with the reasons for selecting the particular methodology used. The study was completed at the end of 1998 and demonstrated the viability of underground mining at Bingham Canyon. Funds have been approved for further drilling and technical studies, which will lead up to a feasibility study in 2004/5.

Jan 1, 2000

By A Halim

The European Union (EU) have recently issued new Threshold Limit Value-Time Weighted Average (TLV-TWA) for diesel exhaust contaminants, which are CO, NO2 and DPM. The new limits for CO and NO2 were issued in 2017 whilst the one for DPM was issued in 2019. However, in order to allow EU mines to formulate strategies to comply with these new limits, the EU granted a transition period in which mines could use the old limits until the new limits are enforced. The new limit for CO and NO2 will be enforced from 21 August 2023 whilst the one for DPM will be enforced from 21 February 2026. The new limit for NO2 and DPM is very low, 0.5 ppm for NO2 and 0.05 mg/m3 of Elemental Carbon (EC) for DPM. Combination of these two limits would be the lowest among all mining jurisdictions worldwide. It poses a huge compliance challenge to EU mines if they keep using diesel machines. Therefore, a study and a field trial were carried out by the author in 2019–2021 to investigate whether replacing diesel machines with Battery Electric Vehicles (BEVs) would be the best answer to this challenge. This paper outlines results of this study and field trial.

Oct 12, 2022

Reconnaissance geochemical exploration in the vicinity of low angle detachment faults which bound the core of the Paparoa metamorphic core complex yielded Au up to 14 ppm, with 35% of greywacke, granitoid and quartz vein samples in the northern range exceeding the 0.01 ppm detection limit. Au is associated with Ag, As, Sb and Cu anomalies consistent with epithermal-type mineralisation. The Ag and Cu anomalies also distinguish this mineralisation from older, mesothermal Au deposits widespread in the Ordovician 'slate belt' greywackes, which comprise much of the upper plate of the core complex. Baryte, molybdenite, fluorite and stratiform U mineralisation in the northern Paparoa Range may also be related to hydrothermal activity along the detachment fault zones.

Jan 1, 1995

By A R. Gerson

Pyrite, chalcopyrite and mixed sulfide samples, with and without quartz (5 wt per cent S), were subjected to column leaching to mimic natural weathering (cyclic wetting and drying). The pH and SO4 2- concentration of the column effluent was measured over a period of 78 weeks. The pH of the pyrite-only containing column rapidly decreased and remained under pH 4 after 12 weeks of leaching. The pH calculated assuming a 2:1 ratio of H + generation and SO4 2- release was slightly lower than that measured. However, a reduced H + to SO4 2- ratio of 1:1 is predicted if the release of aqueous Fe 2+ is assumed rather than the formation of Fe(OH)3. The pH of all columns containing only chalcopyrite or a 1:1 mole ratio of chalcopyrite and pyrite remained at or above pH 5 for the duration of the leach even though significant SO4 2- was released. One column containing the same initial surface area of pyrite and chalcopyrite but only approximately 0.10 the mole fraction of S as chalcopyrite maintained a pH of greater than five for the first 56 weeks of leaching and showed sporadic acid production thereafter. It is well established that oxidation of chalcopyrite results in a surface layer of polysulfide material. It is the formation of polysulfide that neutralises the acid produced on S oxidation through to SO4 2-. Hence where polysulfide formation occurs extensively on chalcopyrite the resulting solution pH decrease will be less than that based on SO4 2- production. The oxidation rate of sulfide minerals increases with decreasing pH and hence acid formation via sulfide oxidation to SO4 2- causes the subsequent oxidation rate to increase. The addition of calcite (CaCO3)to a pyrite column not only neutralises the acid formed but also decreases the rate of release of sulfate to solution by a factor of approximately 30. This is also the case where chalcopyrite is present mixed with pyrite. The rate of release of sulfate from the mixed sulfide mineral columns (after the initial release of the sulfate already present) was between one-fifth and one-tenth that in the absence of chalcopyrite.

Jan 1, 2003

By D P. Blair

The theme of this conference is blasting productivity. This article only considers the technology aspect of this theme, and in particular, the collection and analysis of experimental data. In many cases, field trials are set up to collect data on variables such as fragmentation and vibration with the aim of comparing different explosive products and/or blast designs. An important aspect of such trials is the collection of sufficient data to draw sound conclusions. In this regard, there is no doubt that the scatter in real data is the root cause of all problems of obtaining misleading results due to an insufficient number of trials. This article shows that the typical one-off trial has a high probability of producing misleading information, which could be considered to be worse than having no information at all. Assuming that sufficient data has been collected, this article also highlights the methods that can be used to make the most of that data. These methods include the application of appropriate statistics that are dependent on the nature of the scatter in the data, and the use of some of the more recent filtering and spectral approaches that can be used to reduce the noise in measured blast signals and increase the resolution of their spectral characteristics.

Nov 8, 2011

By Butt C. R M

Resurgence in Au exploration during the past decade has been characterised by a considerable emphasis and dependence on geochemical procedures. This has been made possible, firstly, by marked improvements in analytical sensitivity over those previously available and secondly, of particular importance to exploration in Australia, by a better understanding of the distribution of Au in the regolith, which has led to the optimisation of sample media. These developments have given exploration companies the ability to seek and detect subtle and widespread geochemical signatures of concealed Au mineralisation and provided an enhanced capability to interpret the data. As a consequence, several new discoveries have been made, even in areas that have been intensively explored in the past. In the deeply weathered Yilgarn Craton (WA), and in equivalent areas elsewhere in Australia and overseas, Au has accumulated in the upper lateritic gravels and duricrusts of the regolith, probably during humid climatic periods in the Tertiary. The laterites may not only be Au ores in themselves, but research by CSIRO and CRC LEME has shown them to be very important sample media, (eg Anand and Smith, 1992). In many areas, however, the laterite has been eroded and hence is unavailable as a sample medium and chemical modification under more and conditions since the Tertiary has leached Au from the upper saprolite. This has greatly increased the difficulties of exploration, particularly where reliance was placed on sampling between 2 and 15 m of the surface. Further research, however, has demonstrated that, despite this leaching, recent remobilisation of An has caused it to concentrate in a specific soil component, pedogenic carbonate, usually in the top I - 2 m, thereby giving surface expression even to mineralisation that is concealed by over 20 in of leached overburden. Secondary carbonates, commonly referred to as calcrete, may precipitate as calcite and/or dolomite in regoliths where the average annual rainfall is less than about 600 mm. Pedogenic carbonates are those that form in unsaturated (vadose) soil horizons. They are widely distributed in the Gawler and Yilgarn Cratons. In the Yilgarn Craton south of about 30¦S ('the Menzies Line'), they are seemingly more abundant over more basic rocks and towards the south east (Figure 1). In contrast, groundwater calcretes form in saturated (phreatic) environments, typically in the axes of major drainages north of the Menzies Line. These are known to accumulate economically-significant grades of U but not, apparently, An.

Jan 1, 1997

By D Martin

The Rio Tinto (Mount Bruce Mining Pty Ltd) Koodaideri Iron Ore Project is located approximately 110 km north-west of Newman in the Pilbara region of Western Australia. During detailed ecological studies of the project area, a significant maternity roost (containing around 430 individuals) of the Orange Leaf-nosed Bat (OLNB) (Rhinonicteris aurantius) was discovered within the boundaries of the proposed mining area. The OLNB is listed as Vulnerable under the Commonwealth Environment Protection and Biodiversity Conservation Act 1999 and is listed as a Schedule 1 species under the Western Australian Wildlife Conservation Act 1950.With a good understanding of blast vibration attenuation in the Pilbara’s different geologies and in the absence of other known studies, it was considered that appropriate buffer distances between mining and bat colonies were not scientifically determined. Therefore, to inform the environmental approvals process that was underway, a series of seismic blasts was planned to assess and measure the sensitivity of the OLNB to trial-sized seismic blasting activities to develop a more scientifically based buffer zone for the protection of the OLNB. This was to be achieved by testing ground attenuation of the site and measuring any response from the OLNB to the firing of seismic charges. Rio Tinto sought the independent expertise of ecological consultants to evaluate and participate in the work to quantify the level of sensitivity of the bat colony and to outline the proposal to government authorities.After detailed risk assessment and project mapping, the seismic blasts were implemented, with the aim of firing individual charged and measured vector peak particle velocity (VPPV) at the OLNB roost cave, combined with monitoring OLNB disturbance activity within the roost that was invoked by the blasts. A series of six charges were fired with the VPPV ranging from 0.66 mms-1 to 18.70 mms-1. The OLNB activity was monitored using high frequency microphones, which detect bat calls emitted during flight. Under daytime conditions, the bats would normally be dormant, so the null hypothesis was for no calls to be detected if the bats displayed no disturbance behaviour. This work has improved understanding of mining activities (blasting) on the OLNB species, assisting in establishing mining exclusion zones that are based on scientific data, contributing to a sustainable future for both the environment and the mining industry.CITATION:Martin, D, 2015. Scientific evaluation of fauna sensitivity to blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 519–526 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015