Search Documents

By Weller KR, Restarick CJ, Stewart PSB

Following a detailed assessment of concen trator performance at Broken Hill South Limited which was reported in a previous paper, the fine grinding section was changed from a parallel arrangement of the two grinding circuits to a series arrangement, and the concentrator per- formance re-assessed. The change to series grinding had virtually no effect on the actual or potential capacity of the circuit to make a final product with 80% passing 100 mesh. However, the fresh flotation feed contained significantly less +150 mesh lead and +65 mesh zinc (material which was shown to float poorly), without an increase in the quantity of poor-floating ultra-fine lead and zinc. From the size-by-size flotation recovery data, it was shown that overall recoveries of both lead and zinc were approximately 1% higher than they would have been without this change in size distribution and it was concluded that this was a direct result of the change in grind- ing procedure.

Jan 1, 1972

By Piga P, Sammarco O

Ventilation and the environmental climate in the Campiano mine is the subject of this re- search. The mine is located in Southern Tuscany (Central Italy), a region where geothermal gra- dients are very high (three times the average gradient of the earth). The research produced interesting indications as to the influence of surface climatic conditions on the environmental parameters inside the mine. A close correlation has been found between dry-bulb temperature and humidity ratio of the air in the mine for dif- ferent metereological conditions and for differ- ent mass flow rate values. Variations in air enthalpy, caused only by the heat exchange with the rock walls during the flowing of the air through the mine, depends on the surface temperature values. Statistical analyses have been used to ex- press air enthalpy variations on surface tempe- ratures, on the variations of the humidity ratio that the air undergoes inside the mine and on the mass flora rate. The application in practice of the results will permit the identification of correct mea- sures to be adopted so that optimal microcli- matic conditions are produced in the mine.

Jan 1, 1986

By A Keogh, P Allen, P Stoker

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Private equity (PE) firms are comparatively free of mandatory requirements for the level and scope of due diligence applied prior to making investment decisions in minerals projects when compared to listed entities, sovereign funds or financial institutions adopting the Equator Principles (Equator Principles Association, 2013). While this freedom allows for flexibility, agility and innovation in making investment decisions, it can also expose PE firms to material risks that may impact their ability to successfully list the projects or attract later financing.Financial institutions and investors with mandatory due diligence and disclosure standards may refrain from investment in or acquisition of a project if it fails to meet various performance requirements. There are many high-profile projects that have suffered significant write-downs on book value after acquisition because specific non-mining issues were not adequately assessed. Thus, a PE firm may be left with an asset that is difficult to divest and incapable of securing development finance.PE firms can manage this risk by being aware of the growth trend in the adoption of ‘international standards’ in addition to host nation standards and legislative requirements. This paper outlines key issues for PE firms to address to maximise the chances of obtaining funding or successfully taking an exploration or mining project through to listing or divestment. Two steps are required: identification of gaps in performance and priority matters of interest to financial institutions and development of action plans to ensure that the priority requirements are met or capable of being met.A PE firm can set its project for success by understanding the social and environmental performance requirements of international standard financiers and by setting the project on the right path to meeting these requirements, and thus making it an attractive investment.CITATION:Allen, P, Stoker, P and Keogh, A, 2015. Setting for success – private equity exploration and mining project buy-in to listing and divestment , in Proceedings PACRIM 2015 Congress, pp 93–100 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By J Heyes

Historically mining engineers haven't spent enough time planning waste dumps, but waste movement costs often outweigh ore haulage costs. There is a real incentive to plan waste dumps right the first time to minimise rehandle and final closure costs. At BHP Billiton Iron Ore there has been an increasing sophistication in waste dump design and they are becoming as important as the pit design. Closure landforms are now included in mining studies. Closure is embedded in the business planning cycle. The results from the recent life of mine study at Whaleback is a case in point where a base case of the shortest hauls with no closure constraints was compared against a closure case. A properly planned and executed waste plan revealed that no rehandle was required and haulage costs were eight per cent less if closure design implementation was carried out concurrent with mining. At cessation of mining the landforms were such that decommissioning of critical acid rock drainage dams and coverage of exposed pyrite areas could occur straight away, without the need for additional rehandle.  The paper also covers design and scheduling elements of waste design both in-pit and ex-pit, management of potentially acid forming material (PAF) and trends in PAF management and designing for final landform closure. This paper illustrates that there is value in terms of costs savings, sustainable outcomes and reputation if the mine planners are involved in the closure planning process.

Jan 1, 2009

By Sheer T. J

The increasing demand for underground cooling in South African gold mines has resulted in various cooling methods being con- sidered, including the use of ice. Two main areas in connection with ice cooling systems are being investigated. The first concerns the efficient and cost effective production of ice on a larger scale than previously required for any other application. The second con- cerns the transportation of ice in pipes from surface ice-making machines to underground melting sites.

Jan 1, 1988

By Kohra A, Shoji S

The amount of copper production by flash smelting process occupies about 17% (equivalent to 1.4 million t/year) of total free world production. In Japan, 650,000 tons of copper is produced annually by flash smelting. This is 65% of the gross copper production of Japan. To reinforce pollution control, promote energy saving, and enhance production efficiency by increasing the size of furnaces, conventional blast furnaces and reverberatory furnaces are being replaced with the flash smelters worldwide. The Ashio Smelter started copper production in 1884 and developed in association with the Ashio mine. In those days, the Ashio smelter produced copper by using the blast furnace process designed for the high-grade ore from the copper mine. At that time, this process was specialized in Japan. In 1956, for the first time in Japan, the Ashio Smelter introduced the flash smelting process developed by Outokumpu Oy of Finland (it is suitable for treating the copper concentrate, producing sulfuric acid and improving production efficiency). The flash furnace in Ashio, the first ever in Japan, had a capacity of 230 t/day for copper concentrate and was operated up to 1962. During this period, various operational troubles were solved, and further improvements were made; and, in 1962, a Furukawa-type flash smelting furnace was completed in Ashio. This improved version of a flash furnace had a capacity of 450 t/day. There was one flash furnace and one waste heat boiler, which were arranged in a unique pattern for that time. This furnace may be said to be the prototype of the present flash smelting process in the world.

Jan 1, 1987

Cobar Mines Pty. Limited (CMPL) uses sodium sulphite as the principal depressant to attain selectivity in copper flotation prior to sequential recovery of lead and zinc. The usage of sodium sulphite is examined both from a theorectical viewpoint ana from the manner in which the copper circuit at (MPL has developed. The results of relatively recent investigations, both in the laboratory ana the plant, are discussed aria shown to support the present operating Techniques.

Jan 1, 1983

By B Waldon, M Valastro

A coal dust explosion is one of the most significant risks in the harsh and complex environment of an Underground Coal Mine (UCM). Reviewing literature, regulations and existing systems surrounding explosive dust management shows that there have been few advancements in managing this risk over the past 90 years. Legislation has remained relatively stagnant and minimal systems are implemented in the real world that can simplify, standardise and improve the effectiveness of UCM explosive dust management. To help bridge this gap, Corehesion, in collaboration with an UCM has designed, developed and implement an Explosive Dust Risk Mitigation System (EDRMS) utilising components of Business Intelligence (BI) that is capable of real-world use in industry. To do this the existing explosive dust management process at the associated research mine was evaluated to form high-level and detailed design requirements, focusing on digitally simplifying the procedure, not replicating it. The system was then iteratively and incrementally developed and implemented at the research mine to commence real-world use. The developed BI platform is compared with the existing process to highlight the advancements in performance transparency, efficiency and optimisation of UCM explosion mitigation. This comparison and evaluation of the real-world system implementation at the research mine demonstrate its success in automating procedure steps, providing a readily accessible source of data and enabling a proactive approach to planning and managing explosion risk mitigation. In addition to improvements just for the research mine, this EDRMS created directly address many Queensland regulatory audit findings. By finalising the total system and making the highlighted changes for standardisation, this BI system will have the adaptable capabilities for implementation across the UCM industry. As accurate data availability improves at UCMs, further work can be done to improve the systems’ optimisation techniques and integration of other risks.

Apr 16, 2024

By O N. Antzutkin, A V. Ivanov, W Forsl

Polycrystalline and surface complexes (at synthetic sphalerite, ZnS, and galena, PbS) of zinc(II) and lead(II) ions with eight different O,OÆ-dialkyldithiophosphate (Dtph) substances have been prepared and comparatively studied by means of 31P CP/MAS NMR spectroscopy. The 31P resonances have been assigned to dithiophosphate groups with terminal S,SÆ-chelating or bridging coordinations in the mono-, bi-, tetra- and polynuclear complexes respectively. The bridging coordination of two neighbouring zinc(II) ions by O,OÆ-dialkyldithio-phosphate ligands was established at the surface of synthetic sphalerite.The adsorption mechanism of dialkyldithiophosphate on synthetic galena includes formation of a surface complex as well as surface precipitation. Principally different coordination modes of the reagent were discovered at the surfaces of galena and sphalerite (ie terminal S,SÆ-chelating coordination to the lead atom).Derivatives of monothiophosphoric and phosphoric acids were displayed as hydrolysis products of dialkyldithiophosphates at synthetic PbS.

Jan 1, 2005

By D Luppnow, C Hore

In-pit tailings storage can provide many advantages when compared to typical above-ground tailings storage facilities (TSFs). As regulations become more restrictive and existing mines expand into new pits, the motivation and opportunities for in-pit tailings disposal is increasing.The Langer Heinrich uranium orebody follows a palaeo-river channel and is mined as an open pit operation. The mine pits intersect two main aquifer systems, one at the surface and one at the base of the orebody/pits. The tailings storage methodology is full in-pit disposal in multiple TSFs for the life-of-mine. Continuity of the initial hydrogeological conditions is incorporated in the design by the use of the pervious surround concept and the reinstatement of the lower aquifer (palaeochannel aquifer) at the base of the pit. Containment embankments are required to facilitate the staging of the TSFs development and are constructed using waste rock liberated during the mining of the pits. All of the TSFs are equipped with decant structures and an underdrainage system is included to improve water recovery, enhance consolidation and increase tailings density.This paper presents the design of a unique in-pit tailings storage solution for the Langer Heinrich mine in Namibia owned by Paladin Energy Ltd.CITATION:Hore, C and Luppnow, D, 2015. In-pit tailings disposal at Langer Heinrich – tailings storage facilities in a unique hydrogeological setting, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 373–380 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By T Walsh, S R. Mudnuru

The development of lithium-ion batteries, coupled with the global trend towards electrification of transportation, has led to a dramatic increase in the demand for lithium. The production of lithium from hard rock ores is increasing, and flotation has proved to be an effective means for the beneficiation of many pegmatitic lithium ores. Clariant Mining Solutions has developed a range of novel collectors for the flotation of spodumene and other lithium ores, and this paper presents examples of some of the most recent developments. Fatty acids are the typical collectors for lithium flotation, however the grade and recovery achieved with these collectors is often below the desired level. There are also some significant drawbacks associated with the use of fatty acid collectors, such as the formation of calcium soaps which give rise to filtration problems and the need for acid washing. Several FLOTINOR products have been developed as alternatives to fatty acids. These products offer equivalent or better metallurgical performance at significantly lower dosages than fatty acids. This offers benefits to the flotation circuit as well as potentially reducing the issues associated with downstream processing of the concentrate.

Aug 24, 2022

The Porphyry Gold Mine (150km NE of Kalgoorlie) was reopened in November 1983 with production commencing in April 1984. Original reserves quoted for the open pit were 822000 tonnes at 5.2 g/t Au based on wide spaced diamond drill holes. Close spaced grade control drilling has revealed some loss of tonnage and a significantly lower grade. In the area of the pit mined to 30 June 1985 this grade control reserve estimate contained 67% of the gold in the original ore reserve with the grade being 19% lower. It is anticipated that the final grade control reserve estimate will contain around 80-85% of the gold contained in the original reserve. There has been close agreement between the Mill Head grade (4.19 g/t Au) and the grade control predicted grade (4.2 g/t Au) confirming that dilution is not a major problem. After initial poor agreement (attributed to "lock-up" in the circuit) the bullion calculated head grade steadied out at 93% of the grade control prediction. This difference is considered to represent the geostatistical bias in the drill hole/crushed rock sampling. Gold recovery has been in the range 93-95% (compared with bullion calculated grade). The net result is that the recovered grade of ore mined to 30 June 1985 is 70% of the original ore reserve grade.

Jan 1, 1986

By Warner RE

SINCE 1952, when Elliott et a/ first applied the Sherwood correlation for flooding in chemical absorption towers to blast furnaces numerous investigators throughout the world have followed their example and much research effort has been spent to tighten the correlation and recently to extend investigation of flooding to side gas entry conditions. The widespread use of the Sherwood concept of flooding has been such that even the word itself has become an integral part of blast furnace nomenclature. The evidence for the applicability of Sherwood's relationship has been that the flooding limits calculated from blast furnace parameters lie approximately on the Sherwood line. However, the values of many of the variables for the blast furnace calculation are only estimates and at first sight one may wonder at such 'close' coincidence when some of the estimated parameters entering the Sherwood correlation are raised to the power of three or more, as for the bed porosity and the liquid surface tension. It is felt that the explanation of this result lies in the logarithmic: nature of the plot and/or the fortuitous can- cellation of the errors of the estimates in the calculations coupled with the fact that blast furnace fluid ratios lie within a very narrow range of values. The foregoing considerations should in their own right place doubt on the correctness of the Sherwood type flooding correlation applied to the blast furnace. Additional doubt regarding the existence of the Sherwood type flooding in the furnace has been cast by the results obtained in the Tokyo University experimental blast furnace. From the reasoning of both Standish and Colquhoun (p. 20) and Warner (p. 23) it is deduced that flooding in the traditional sense will only normally occur in the upper bosh (somewhere near the mantle), following softening as discussed by Palella et a/ on p. 75, and flooding in that zone is likely to result in furnace irregularity. On the other hand, the concept developed by Warner of slag hold-up above the raceways as a stable phenomenon not affecting furnace regularity is a process unique to the blast furnace and is not described by the Sherwood flooding theory. Recognising the considerable practical implications of slag hold-up above the raceways, this note further explores the physical process of slag hold-up. We envisage that bed of coke above the raceways in almost all blast furnaces would contain some slag held up by the gas pressure gradient. In general the slag would be contained in a ring and gas would bubble through in its ascent through the furnace. The force supporting this slag is the pressure gradient and obviously -much of the blast pressure is dissipated in supporting this structure.

Jan 1, 1975

By M Spagnolo, M Ashley, D, L Reemeyer

PasmincoÆs Century Concentrator in North West Queensland commenced operations in November 1999. The nameplate production capacity of 500 000 tpa of zinc metal production in concentrate was achieved in August 2002. Completion of the production ramp up was successful due to the culmination of a number of initiatives throughout 2001 and 2002. Mine to mill interaction to understand and eliminate head grade related bottlenecks affecting Concentrator production and reduce feed variation. Grinding circuit process development û operating and process control strategies to improve stability and reduce grind size to support zinc recovery. Pumping upgrades to control spillage in ultrafine zinc flotation Low density zinc flotation strategy û to improve silica-sphalerite separation to improve zinc recovery while maintaining acceptable silica in final concentrate. Flotation circuit process development û froth crowders, froth cameras and reagent control strategies to improve primary zinc flotation performance. Review and implementation of longer campaigns between planned shutdowns to improve availability. Team reorganisation û to improve setting and implementation of metallurgical strategies. This paper describes these initiatives and their contribution in achieving the production target. It also notes the ball mill motor failures that delayed the successful achievement of the ramp up, and CenturyÆs response to minimise the production impact. The paper also outlines the capital improvement program that was implemented to improve zinc recovery to design 82.5 per cent recovery once the production rate had been achieved.

Jan 1, 2003

By Bangerter PJ

The use of gravity concentration is, and has always been, the conventional primary method for gold recovery from alluvial deposits. The development of high capacity cone concentrators and metallurgically efficient wash-waterless spiral separators has had some impact in the technology for alluvial gold processing, but perhaps more significantly has led to the relatively recent use of this gravity concentration technology in grinding circuits of hard rock ore for "coarse" gold removal and for scavenging gold locked in sulphides from cyanidation tailings streams.Gravity concentration systems are relatively low-cost, non-polluting and energy efficient; and their judicial use in gold treatment plants can significantly reduce overall capital and operating costs.The application of modern gravity concentration technology to hard-rock and alluvial gold ore treatment is discussed. Flowsheets and test and operating data from a number of gold processing operations incorporating gravity concentration treatment are presented.

Jan 1, 1984

By Singh TN

Rampura-Agucha Zinc-Lead deposit is unique as it is reported for the first time in the gneissic terrain with a rich oregrade quality of early to middle Proterozoic of Bhilwara supracrustal belt in the Precambrian of Northwest India. These sulphide ores are mostly confined to the graphite bearing Quartzofelspathic gneisses with intermittent bands of Calc-Silicate granofels and amphibolite. The ore and country rock mineralogy and their textural features are indicative of highly metamorphosed deposit and further the presence of marmatite and monoclinic phyrrhotite revealed high temperature environment of deposition.The present paper deals with some of the ideas about the ore genesis and petrographics of the associated rocks for Rampura-Agucha Zinc-Lead deposits of Bhilwara District (Rajasthan).

Jan 1, 1990

By M Dusci, A Trueman, S Poos, R Baumgartner, M Brittan

The Canahuire epithermal Au-Cu-Ag deposit in southern Peru is a complex and challenging deposit for metallurgical studies. It has issues of gold locking in sulfides and non-sulfides, deleterious elements and acid rock drainage (ARD). From scoping study to feasibility study, there has been considerable improvement in the understanding of the important geometallurgical characteristics that need to be measured and modelled. This paper presents the current understanding and the requirements to continue to provide optimal models for mining studies.Significant effort has been put into understanding the genesis of the deposit. Improved spatial and temporal understanding of lithology, alteration, structure and mineralogy was used to build a geological and alteration model of the deposit.Early metallurgical programs quantified the effect of head grade on process plant recoveries, but the geometallurgical and statistical analyses did not identify other physical characteristics that influence these recoveries. The studies improved the understanding of the nature of locked gold which can occur as minute inclusions (< 5 ¦m) in sulfides (primarily pyrite with lesser arsenopyrite, pyrite being 100 times more abundant than arsenopyrite) and gangue minerals (quartz and carbonates) as well as solid solution in arsenopyrite and pyrite.The presence of pyrite and the limited buffering capacity of waste rocks increases the potential ARD, which will require mitigation costs before, during and after operations. Waste rock ARD potential has been classified and incorporated in the geometallurgical model. The current classification of waste rock at Canahuire, using international classification standards, is limited due to the complexity of the deposit.Complex deposit metallurgy necessitates a complex process flow sheet, including flotation and cyanidation. Economic recovery will be constrained by the relationships between economic variable grade, other elements and mineralogy. These constraints and inter-relationships are difficult to establish throughout the deposit with a single test. A follow-up geometallurgical program is under investigation and will attempt, with the help of additional test work, to map areas of higher and lower recoveries. It is hoped that metallurgical response can be linked to measurable parameters other than head grade. If this is possible, these factors can be incorporated into future geometallurgical models.CITATION:Baumgartner, R, Dusci, M, Trueman, A, Brittan, M and Poos, S, 2013. Building a geometallurgical model for the Canahuire Epithermal Au-Cu-Ag Deposit, Southern Peru - past, present and future, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 51-58 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By O Arafat, K M. Bartholomew

A voracious consumer of energy and grinding media, the modern ball milling circuit has a huge direct cost impact on a mineral processing operation. Through optimisation, grinding also has the potential to unlock great improvements in recovery and throughput, but how can the complex interactions between mills, classifiers, tonnage, ore-type and downstream recovery be measured, understood and managed in a systematic manner?Functional performance analysis provides the tools and insights needed to measure, understand and improve the two key process efficiencies in ball milling circuits: classification system efficiency (CSE) and mill grinding efficiency.CSE measures the composite performance of the classification system as a whole. In short, the purpose of the classification system is to ensure that grinding mill energy is used to grind coarse particles while minimising overgrinding. CSE is simple to measure in the plant and it provides immediate feedback to the plant metallurgist, mill superintendent and management about the performance of the classification system and the amount of wasted energy in the grinding plant.Mill grinding efficiency measures the capacity of the grinding mill to convert feed-sized material into product-sized material on a tonnes per kilowatt hour basis. It is normalised based upon the ore resistance to breakage, so it provides feedback about the ‘health’ of the milling process under varying operating conditions and ore types. Mill grinding efficiency is measured at the same time as CSE through circuit sampling.Functional performance analysis combines CSE and mill grinding efficiency to provide a measureable, manageable optimisation objective. It also provides a link to tonnage, ore type and recovery. As a result, systematic optimisation of a grinding circuit is a measureable and manageable process to meet business objectives.CITATION:Bartholomew, K M, McIvor, R E and Arafat, O, 2014. Functional performance of ball milling circuits – a plant metallurgist’s tool for process characterisation and optimisation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 227–232 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By Hewitt D

A study of two laterite profiles developed on a serpentinite near Rockhampton, shows that loss of Si02 and MgO results in the relative concentration of Fe203, A1203 and a number of minor elements. Serpentine is broken down to form montmorillonite, goethite, quartz and kaolinite. Enrichment of nickel occurs, and it is shown that the element is mainly associated with montmorillonite and serpentine. Highest nickel values are associated with a zone in the profile which occurs at a depth of 10.5-22 metres, and the bulk of the nickel in this zone (42-80%) is associated with the

Jan 1, 1974

In general the iron ore industry has been slow to adopt the Whittle Pit optimising software in the evaluation of iron ore deposits. The reasons for this are two-fold:the iron ore industry has developed techniques, usually bespoke software residing in the corporate offices of the respective iron ore companies, to establish their final pit limits; and the fact that the Whittle software doesnÆt easily lend itself to estimating a sales product of constant quality without maximising grade (metal content). The Whittle software is based on the work done by Lerch and Grossman (in the early 1970s), which proposed that graph theory be used to establish an optimal surface that maximises the revenue from a deposit. The maximised surface created in the pit optimiser is translated into a proposed optimal final pit shape that can be used by the mine design engineers as a target outline to lay out the final practical pit. By treating a geological and ore resources model that was created for an iron ore deposit as a subset of the recoverable resources estimation (RRE) type of geological models, the evaluation of an iron ore deposit and establishing the final pit is greatly simplified in the Whittle 4-X optimiser. Instead of trying to optimise the iron content of the deposit, the emphasis swings to maximising the extraction of a finished and saleable iron ore product. This is achieved by treating the finished saleable iron ore as an element in the multi-element Whittle optimiser. The quality of the finished sales product is represented, and the material that cannot be used in the blended product is also shown. Proposals for enhancing the functionality in the Whittle 4-X optimiser to make the evaluation of iron (and coal) deposits easier includes the creation of a new reporting function that will allow the user to specify which field(s) can be used as the divisor(s) for the reporting of the element grades in the model.

Jan 1, 2007