Search Documents

By N M. Rana, A Take, N Ghahramani, S McDougall, S G. Evans

A critical issue associated with mining operations has been the stability of tailings impoundments. Some breach events have produced catastrophic tailings flows that have caused significant economic damage, mass casualties and long-lasting environmental impact in the downstream environment. This paper reports independently estimated values of runout distance, inundation area and fahrboschung of 16 tailings flows. The adopted methodology involves the geospatial analysis of satellite and aerial imagery to classify each tailings flow into a primary impact zone (Zone 1: main overland flow) and a secondary impact zone (Zone 2: along-creek diluted flow) to characterise runout. Only Zone 1 runout values are reported herein given the greater significance in relation to downstream impact. The fahrboschung is calculated using elevation data from global 30 m digital elevation models (DEMs) and source literature. The results show that all the selected tailings flows travelled long distances (2.4 km to 98.5 km) and inundated large areas (0.35 km2 to 27.0 km2) over very low fahrboschung values (0.04° to 4.8°). This indicates very high flow mobility that is largely governed by the high water content sourced from interstitial waters and, in many cases, supernatant ponds. Scatter plots display poor correlations owing to the complexity and variability in travel path characteristics (confinement, slope angle and obstructions) and the inherent properties of the flowing mass. The slope angle of the travel path exerts a strong control over the flow velocity which has implications on kinetic energy and downstream geomorphological impact. Mean tailings flow velocities may range from ~6 m/s on near-flat, open terrain to over 30 m/s in relatively steeper, channelised travel paths, indicating that tailings flows fall within the extremely rapid and high mobility spectrum of global mass movements. The presented work forms an inceptive part of the CanBreach tailings project, a major component of which is to develop a comprehensive database of case histories to examine the role of geotechnics, failure modes and downstream terrains in influencing tailings flow behaviour.

Jul 1, 2021

By M Berry

Many mining companies routinely use benchmarking to review their operational activities and associated costs. The aim is to measure operational performance against industry norms, and identify areas where a company is performing better or worse than industry best practice. The goal is continuous improvement.In general, mine technical services, including mining geology activities, are not routinely benchmarked. There are exceptions, such as the cost of drilling per metre and the average discovery cost per unit of metal, but generally mining geology activities are only included indirectly in mining benchmarking studies.Aspects of benchmarking can play a critical role in assisting mining geologists to improve the efficiency and effectiveness of the services they provide. Industry norms for many generic mining geology functions have not been developed and measured, and therefore it is impossible to use external benchmarking to assess performance against other mines. But when used in parallel with quantifying the value of mining geology functions and establishing strategic goals for the team, key components of benchmarking methodology can provide essential feedback on how a team is performing against these strategic goals.CITATION:Berry, M, 2014. Benchmarking – does it have a role in improving the performance of mining geology?, in Proceedings Ninth International Mining Geology Conference 2014 , pp 361–366 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By D L. Reid, G Nwaila, J Petersen, J-P Franzidis, Y Ghorbani, M Becker, F C. de Beer, L C. Bam

Traditional methods of gold extraction have involved comminution and processing via cyanide leaching, all of which are associated with energy, cost and environmental implications. Subsequently, numerous opportunities for improvement and optimisation strategies in gold mining and processing have been explored, including heap leaching, which has significantly lowered comminution costs. This paper explores the effect of the more energy efficient high-pressure grinding rolls (HPGR) on the comminution behaviour (especially on the crack density) and cyanide leaching performance of laboratory reactors study on run-of-mine gold ore comprising the Ventersdorp Contact Reef (VCR) and the Elsburg Reefs (ER), sourced from Carletonville in the Witwatersrand Basin in South Africa. The ore was comminuted using HPGR at three different pressure settings (120, 90 and 60 bar). Large (-16/+11.2 mm) and small (-5.6/+4 mm) particles of the HPGR product where then mineralogically characterised using optical microscopy, quantitative evaluation of minerals by scanning electron microscopy (QEMSCAN) and X-ray computer tomography (CT) before cyanidation. The results of the leach experiments indicated a correlation between gold extraction, particle size and crack density. Mineralogical characterisation of the ore indicates that the Fe-sulfides present in the VCR are likely to be more reactive than those in the ER, thus having a more favourable influence on gold cyanidation. Overall, the results show promise for the heap leaching of Witwatersrand gold ores prepared using HPGR and demonstrate the value of a multi-disciplinary geometallurgical approach.CITATION:Nwaila, G, Becker, M, Ghorbani, Y, Petersen, J, Reid, D L, Bam, L C, de Beer, F C and Franzidis, J-P, 2013. Morro do Ouro geological model with a metallurgical view, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 75-84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By J Theiler, B Beamish

Spontaneous combustion hazard assessment from an environmental impact perspective is not well understood and is seldom given due consideration in environmental impact statements. In surface mining operations, self-heating, leading to spontaneous combustion may occur when rock units containing reactive metal sulphides and organic carbon are disturbed by mining operations and exposed to the atmosphere. When these rocks are present self-heating will occur in situations where the rate of heat generated from oxidation reactions exceeds the rate of heat lost to the surroundings. The processes and mechanisms that lead to spontaneous combustion events are varied and generally complex. To effectively manage spontaneous combustion in surface mining operations, it is necessary to characterise the spontaneous combustion propensity of the geological materials involved. Until recently there has been no testing procedure for assessing the propensity of waste rock to spontaneously combust that has been adopted by industry. However, new developments in adiabatic test methods have proven successful in determining the self-heating behaviour of coal (Beamish and Theiler, 2015) and coal containing reactive pyrite (Beamish and Theiler, 2017). These adiabatic test methods have now been modified to assess the incubation behaviour of waste rocks and can be used for their spontaneous combustion characterisation in advance of mining (Beamish and Theiler, 2016). The new method provides a practical means to establish the likelihood of developing a spontaneous combustion event for the specific site conditions. This paper presents examples of the use of a cost effective first pass filter for assessing spontaneous combustion potential of waste rock based on geochemical data from four surface mines. This is supported by adiabatic Incubation Test results for three of the mines and visual examination of cores for one of the mines. CITATION:Theiler, J and Beamish, B, 2018. Valid spontaneous combustion hazard assessment for surface mine environmental impact statements, in Proceedings Life-of-Mine 2018, pp 64–67 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By J Elder

Magnetic separation equipment has long been used to upgrade and beneficiate a wide variety of minerals and materials. Over the years, significant advances in both wet and dry magnetic separators have improved their operability and separation performances, broadening their use.But no one answer exists to the question: what is the right type of magnetic separator? For many minerals, including ilmenite, both process routes may be viable. There are technical, production, as well as economic reasons for choosing wet versus dry. However, recent developments illustrate that a new generation of wet magnetic separators is approaching performance once seen only in dry magnetic separation. With quality and production performance becoming similar, the choice between wet and dry magnetic separation is not as cut and dry as it once was.

Oct 5, 2011

By K Young, M Martin, D Payne

This paper outlines the evolution of managing high consequence risk scenarios in BHP Coal, with particular focus on managing the stability of an endwall that is adjacent to a public infrastructure corridor running through a Central Queensland coalmine. BHP Coal developed a Geotechnical Consequence Register after industry failures identified shortcomings in traditional risk assessment practices. Traditional risk assessments consider the consequence and likelihood of a geotechnical event occurring under normal operational conditions. As such, the risk rating for a high consequence, low likelihood failure may fall within the acceptable range, even where a lack of meaningful geological data exists due to the area being off lease or outside of mining reserves. The Geotechnical Consequence Register lists all geotechnical failure scenarios of high consequence, identifies if current controls are adequate, and highlights if specific Geotechnical Management Plans are required. This case study reviews a failure scenario that was identified through the geotechnical consequence register. The scenario had previously been considered low likelihood and subsequently driving a low risk; however, the likelihood ranking was impacted by a lack of geological data outside of the mining lease and predominately informed by an acceptable historical slope behaviour. Additional exploration identified previously unmapped faulting which increased the risk rating. The requirement to develop a specific management plan resulted in an increase in the required factor of safety, design changes, the implementation of additional monitoring and a corresponding monitoring Trigger Action Response Plans (TARP). In the case study area, the initiation of a geotechnical instability was identified early through the increased monitoring program. The instability was successfully managed and any impact to the infrastructure corridor off lease was prevented. BHP Coal has used the Geotechnical Consequence Register for several years to identify and assess high consequence geotechnical failure scenarios. In some areas this has justified additional exploration, more stringent design acceptance criteria and an increased level of geotechnical monitoring. The process has been successful in ensuring that geotechnical risk is controlled in areas that often receive less attention than active production areas.

Nov 29, 2022

Two characteristics of the modern mining industry are that there is a skill shortage and that young professional people rise rapidly into highly responsible supervisory positions. With this responsibility comes the burden of identifying and managing health and safety risks. Without the benefit of a comprehensive health and safety training program, these young professionals may be putting both themselves and those under their supervision at risk. The Moura Mine explosions and the asbestos health disaster should not be just artifacts of history, but highly valued lessons that impress the need for comprehensive health and safety risk management strategies on young professionals. From the perspective of the former secretary of the Committee to implement the findings of the Moura (Disaster) Inquiry and as the former coordinator of the Coal Workers Health Scheme, key issues in occupational health and safety management systems are explored.

Jan 1, 2005

By D Finn, D Kentwell

Experience has shown that the E-Type multiple indicator kriging (MIK) estimation technique often works well for resource estimation in stockwork mineralisation that contains a mixture of high and low-grade mineralisation types that are difficult or impossible to separate spatially. E-Type MIK, like ordinary kriging (OK) is a smoothing estimator and where data is sparse can result in estimates of grade tonnage curves that do not reflect the true block variability at selective mining unit (SMU) scale. The rank and replace (RR) estimation methodology is designed to reproduce both local block accuracy and true block variability at SMU scale and has shown good results when used with highly skewed unimodal diffusive style mineralisation. This paper examines the use of RR with mosaic style mineralisation typically found in stockworks via a case study using real data from Newcrest’s Telfer West Dome deposit. Resource level estimation results for ordinary kriging (OK), E-Type MIK and RR are compared to close spaced grade control models as the reference reality.Results show that stationarity requirements and declustering can severely impact on the usefulness of the rank and replace technique and that it should only be used where trends are not too strong and data are relatively uniformly spaced. This does not rule out its application to stockwork or mosaic style deposits. However, in this case, the presence of trends and different data densities requires the non-stationary domain to be further broken down into sub domains for the RR technique to be effective.CITATION:Kentwell, D and Finn, D, 2017. Testing new estimation techniques – rank and replace: a stockwork case study, in Proceedings Tenth International Mining Geology Conference 2017, pp 365–374 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By S Bhandari

A model for predicting dust plume dispersion from blasting operations using the Eulerian mathematical algorithm has been developed. This model considers atmospheric stability, and wind velocity and direction for computing dust concentrations at different distances from the blast. Software has been developed which simulates the movement of a dust plume at a given horizontal distance from the blast location and time elapsed after the blast. The concentration of dust is also given in vertical planes. It takes into account ground profile and atmospheric conditions such as temperature, pressure, humidity, wind velocity, wind direction and shear. Experiments were carried out in two limestone mines to calibrate the accuracy of the predictions made by such model. High volume dust samplers were used to collect dust samples. Difficulties encountered in satisfactory dust sampling and quantification of results have been described.

Nov 8, 2011

By J Loeb, J Dampney, P Cameron

Optimisation of Blast Design and Execution must be done right the first time. It is too late after the ore is broken. Consequences of poor design and execution negatively affect productivity from load and haul through the primary crusher to processing and hence reduce mine site profits. Harnessing and utilising ‘big data’ from geology, geometallurgy, drill hole location, powder loading, blast timing, blast movement and fragmentation to close the loop in blast design and optimise the blast increases productivity across the entire value chain from Mine to Mill. As the internet of things and artificial intelligence increases the quantity of data available, being able to capture and utilise this data to advantage is a challenge. Recent advances in software and hardware together with the increased power of cloud computing allows engineers to close the blasting loop to increase mine site productivity. Numerous case studies over the years detail significant gains from implementing the innovative technologies available to Mine to Mill projects. The opportunity is available for all members of the multi-discipline teams at each mine site to actively ensure productivity improvements are realised and maintained not only in their area, or silo of responsibility but across the entire mine site. This paper refers to recent case studies which outline how significant improvements in productivity are available to all mining operations to increase mine site profitability and dividends to shareholders.

Jun 22, 2022

The economic viability of many Southern African massive mining operations is threatened by excessive dilution. In many operations currently in progress, some stopes are experiencing as much as 115 per cent waste ingress reporting to drawpoints. This paper examines the magnitude, causes and types of dilution and presents a set of general principles for the control of dilution in massive stoping operations.

Jan 1, 2000

By J E. Everett

Maximising ore tonnage at a selected target grade requires that appropriate ore identification criteria be established. Iron ore mining block models may consist of many millions of estimated blocks, each block corresponding to the selective mining unit (SMU), with grade interpolated from drill hole data. Each block can be considered as a potential ore candidate. Analysis of such a huge database can require large computational resources, especially for sensitivity analysis requiring multiple computations. However, an alternative streamlined approach is possible, where the data are compressed to an appropriately smaller and representative subset. The consequent data reduction not only makes it feasible to consider the simultaneous analysis of multiple pits but also considerably speeds up computation, enabling sensitivity analysis of the potential ore tonnage as a function of the required grade. Ore identification criteria can be successfully established using appropriately chosen reduced data comprising less than one per cent of the blocks. The ore identified is virtually indistinguishable in tonnage and grade from the ore that would be selected using the entire block model.Two methods of data reduction are tested: sampling (using a proportion of unaltered blocks) and binning (consolidating groups of blocks to a single average grade). The source blocks are first sorted (such as by location, analyte grade, principal component score, random order or value) before sampling or binning. In this study, the sorting options considered were by location and Fe grade. The effectiveness of each method was evaluated using the block model subsets to select the maximum tonnage of ore at a specified target grade. Block model data from an anonymous Pilbara iron ore project with about one million blocks averaging 1.132 kt were used. The blocks are from multiple resource models, to be blended to a single product. Sampling is shown to be superior to binning because sampling preserves the full variability while binning, although matching the mean block grades reduces their variability.It was found that the appropriately sampled data sets (sorted by location) gave results virtually identical to the results for the full data set, even when the samples comprised less than one per cent of the original blocks. The reduction in computer time to identify maximum tonnage at a specified grade was approximately proportional to the sample percentage. The increase in computation speed greatly facilitated sensitivity analysis. A sampled data set of one-eighth the total block model was used to investigate the effects of changing each of the component grades around the original grade specification. The results of this sensitivity analysis are discussed, and illustrate the potential benefit of carrying out sensitivity analysis in determining feasible and marketable product grades.CITATION:Everett, J E, 2015. Block model data reduction and sensitivity analysis, in Proceedings Iron Ore 2015, pp 263–270 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By V Rodríguez, M Hormaza, R J. Romañach, C Pinzón-de la Rosa

The authors have presented their ideas for developing a powder sampling device in the I-Corps™ program sponsored by the National Science Foundation (NSF). This is an intensive customer discovery program developed to increase the economic impact of the research sponsored by NSF.The I-Corps™ program requires performing at least 100 interviews with potential customers in various industries. These interviews are essential to establish the need for a particular product or solution, and identify potential commercialisation partners and competition. The interviews have revealed the absence of Theory of Sampling (TOS) principles in many companies. The interviews are designed to identify the difficulties associated with current sampling practices that do not meet TOS principles.The I-Corps™ program is a significant challenge for scientists who often avoid discussing a concept in fear of losing their research idea. The program teaches how to obtain information without releasing the important intellectual property related to a product development idea. The I-Corps™ methods have been used to discover the prevailing ideas on sampling in various industries.I-Corps™ also teaches how to present ideas to investors; another significant challenge for a scientist. We are currently learning to present sampling and TOS to investors and business development experts, and will share some of these experiences.CITATION:Pinzón-de la Rosa, C, Rodríguez, V, Hormaza, M and Romañach, R J, 2017. Theory of Sampling meets the National Science Foundation I-Corps™ program, in Proceedings Eighth World Conference on Sampling and Blending , pp 351–354 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By G Booth

Whilst communications systems in the mining industry have evolved over the years, the premise remains consistent that reliable communication is vital for safety and operational efficiency. TodayÆs open pit mines are benefiting from advanced developmental efforts based on mesh networking hardware and software technology. This paper highlights Rajant CorporationÆs adaptation of technology, originally developed for the defence and first responder industries, to provide wireless network connectivity in open pit mining applications. Featured is the large-scale deployment of over 300 mobile, meshing access points in the Bingham Canyon Copper mine near Salt Lake City, Utah, the worldÆs largest open pit copper mine. Many companies have positioned themselves, their technology and their product line in the arena of rugged outdoor wireless broadband mesh networking infrastructure. However, Rajant Corporation has combined specialised command and control software and portable networks which offer network extensibility and redundancy that are not available in any other networking solution. Rajant CorporationÆs BreadCrumb« offers unique traits in portability and non-line-of-site networking nodes which intelligently route and broadcast in standard 802.11 protocol. The advantage of RajantÆs solution is especially valuable for users needing equipment moved easily and rapidly into and out of the theatre of operations with uninterrupted network availability. The main differentiators that set the BreadCrumb« network apart from the competitors are mobility (continuous availability), simplicity, ability to properly load balance and power options. In 2007, RajantÆs BreadCrumb« wireless mesh system was selected by the Kennecott Utah Copper Corporation (KUCC), a wholly owned subsidiary of Rio Tinto, as its primary communications platform for operations within the Bingham Canyon Copper mine, the worldÆs largest open pit copper mine. The Rajant BreadCrumb« technology enables KUCC to gain additional operational efficiencies by tracking, monitoring and managing its copper mining operations. The primary goal of using the BreadCrumb« wireless mesh system Kennecott was to streamline its complex mining operations. KUCC required a high number of moving wireless nodes for improving mine monitoring and control. The Rajant InstaMesh« software running on the wireless BreadCrumb« units connects hundreds of devices to each other while rapidly transporting critical operational data. Kennecott has successfully implemented a large number of BreadCrumb« radios in an interconnected network that allows loader trucks, shovels, pumps, laptops and other production equipment to communicate with each other in real-time. These systems are a mix of secure access nodes that enable data and voice communications across a meshed, self-healing network for fleet dispatch, health monitoring and other critical mining applications. Many of the devices that require wireless communications are moving at all times throughout the wireless mining infrastructure. The BreadCrumb« nodes rapidly adapt to any changes in the network topology, assuring that IP traffic uptime and bandwidth are maximised. The installation layout and data network specifics, as well as maps and data network efficiencies will be detailed in the paper.

Jan 1, 2008

By R Neivandt, Kane, M O&apos, D Browne

Newmont Australia is the operator of the Mt Leyshon mine near Charters Towers, Queensland. Mt Leyshon is an open cut gold mine, which processed on average 5.0 Mt of ore and produced up to 250 000 ounces of gold per year. Mining was completed in early-2001, followed by treatment of low-grade ore stockpiles for a further 12 months. Approximately 250 ha of waste rock dumps have been rehabilitated. Rehabilitation of two of the three tailings storage facilities (TSF) has been completed and the third is in progress. A field performance monitoring system that includes an automated meteorological station, large-scale lysimeters (measurement of net percolation), and in situ moisture content sensors (measurement of moisture storage changes in the cover material) were installed to monitoring performance of the cover systems placed on the waste storage facilities. This paper focuses on the installation and calibration of the in situ moisture monitoring system. The moisture monitoring system provides automated detailed in situ volumetric water content data above and within the large-scale lysimeters. A portable unit that provides spatial in situ moisture content measurements at additional locations on the cover system is also utilised. The paper will focus on installation and calibration of the in situ water content monitoring instrument in the waste rock, coarse cover material, and fine textured cover materials of the tailings facility and waste rock dump cover systems.

Jan 1, 2003

By T McLeod, B Catto

AngloGold Ashanti Australia’s (AGAA) Tropicana gold mine (TGM) geology department seized the rare opportunity of building a new geology department for a new operation: the philosophy, the people and the processes. Not satisfied with the status quo, or simply repeating what was familiar and already known, the vision was for an innovative, agile, multidiscipline, high performance team, capable of delivering on expectations.To achieve this, the geology department has operationalised key components of human resource management (HRM).This paper describes the operational design and implementation of key HRM components: job analysis, organisational design and organisational development. The benefits of this approach are presented in terms of engagement and autonomy in roles, opportunity for role variety and flexibility of the organisational structure. The result is a geology department that provides the functions of mine geology, resource development, regional exploration, survey, data management, geographic information systems (GIS), resource modelling, scheduling, sample preparation, resource coordination and hydrogeology, and even geotechnical engineering for a year!Considerations for application in other geology departments are presented in terms of fundamental requirements and lessons learnt. Fundamental requirements for success have been the sustained support of the general manager, valuing the scrutiny that comes with continuous improvement, high quality HRM systems and tools within the organisation, and a committed leadership group within the department. One of the most important lessons learnt is that a robust process of ‘induction to role’ is critical – the process of familiarising new starters with who we are and the way we work.CITATION:Catto, B and McLeod, T, 2017. Rewriting the rule book – geology organisational design, in Proceedings Tenth International Mining Geology Conference 2017, pp 137–142 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By T Walkemeyer, R Elliott, D Chang-Martin

Over the past decade, discrete element method (DEM) simulations have seen increasing adoption by the resources sector to inform the design of materials handling equipment such as transfer chutes, bins and hoppers. But, if ‘all models are wrong, but some are useful’ (Box, 1979) what approaches are available to check that a DEM simulation is useful? How to avoid garbage in equals garbage out. This work considers what properties of bulk solid flow behaviour are important to transfer chute simulation. Cohesive bulk solids (such as sticky iron ore fines) can develop sufficient strength to form a stable cohesive arch, this phenomenon is not well predicted by measurements of angle of repose. This work presents a two-part approach to the development of a useful DEM model that can be used to add value to the design and optimisation of bulk materials handling equipment. Part 1 is the calibration of not just one, but a range of material models chosen to envelope the range of anticipated materials that will be handled. This work describes the DEM simulation of a batch of direct shear cell tests to develop material models that can be measured by the same metrics routinely used to characterise the flowability of cohesive iron ore fines. Part 2 of this work describes systematic methods for validation of the transfer chute DEM simulations. The DEM model is only useful if it can adequately represent the typical problems observed within a transfer chute, such as blockages due to build-up and cohesive arching. Proper validation requires good observations. Validation examples of site observations are shown side-byside with simulations to demonstrate the adequacy of the DEM model and calibration approach. DEM simulations have the potential to add significant value by allowing engineers and designers to predict material flow-through equipment based on a range of material properties, allowing for stress testing designs and making iterative improvements.

Sep 18, 2023

By J Coombes

"In today’s challenging climate of reduced staffing, limited funding and uncertain markets, we are called on to operate more productively and ‘be more innovative’. As an industry, we are quick to identify our practice areas as a mark of our role in the machinery of the mine value chain. We proudly note our profession – ‘geologist’, ‘mining engineer’ or ‘accountant’ – and demarcate our responsibilities and even our physical space. We even subdivide our disciplines into sacred entities such as ‘logging geologist’, ‘resource geologist’ or ‘structural geologist’ to prevent any blurring as though somehow the confusion will cost valuable disciplinary ground. How can we function professionally to heed the call to be more productive and more innovative?The purpose of this paper is to underscore what is expected from project evaluation, examine the ways in which we work as an industry and explore alternatives used in other industries and environments.The paper begins with a summary of project evaluation expectations and the ways in which disciplines typically interconnect when conducting project evaluations. Next, the paper examines alternative work frameworks and making a distinction between multidisciplinary, interdisciplinary and transdisciplinary frameworks. In-practice examples of these frameworks in alternative industries and contexts provide evidence for application as well as an opportunity to examine their pros and cons.The paper closes with a call to re-examine working practices in the mining industry, with a view to enhancing productivity and heeding the call for greater innovation.CITATION:Coombes, J, 2016. Transcending the mining discipline divide – multidisciplinary, interdisciplinary or transdisciplinary?, in Proceedings Project Evaluation 2016, pp 2–10 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By S J. Clarke, C S. Walker

The South West Rail Link (SWRL) project involved construction of a rail line to service new residential areas in south-west Sydney. The 11 km rail line is conveyed through a short tunnel at shallow depth where it crosses beneath the eight lanes of the Hume Highway. The underpass location is one of the most heavily trafficked within Sydney’s motorway network.The New South Wales Roads and Maritime Services (Roads and Maritime), as the owner of the highway asset, had the responsibility of managing the risks to the highway and traffic associated with the tunnelling project from the pretender stage through to completion. This paper considers the primary risks and mitigation measures employed, including geotechnical investigation, and development of appropriate construction constraints and concept design of an extensive real-time survey system to monitor pavement deformation during the tunnel works.The geology comprises fresh Minchinbury Sandstone in the tunnel invert and side walls, and variably weathered Bringelly Shale in the haunch and crown. Few tunnels have been excavated in these rock types in Sydney, and there is little information relating to the in situ stresses and stress-relief deformations in these materials.During tunnel construction the monitoring data indicated unexpected surface heave of up to about 24 mm. A multiparametric back-analysis of the deformation data is presented, which provides information on the deformation mechanisms and key geotechnical parameters, including rock mass modulus and in situ stresses.The approaches and methodologies developed for the SWRL underpass were effective in maintaining the safe operation and traffic capacity of the highway throughout the construction period, and the analysis of the monitoring data provides a useful reference for similar future projects, or projects constructed in similar ground conditions.CITATION:Clarke, S J and Walker, C S, 2014. Deformation mechanisms of the South West Rail Link underpass beneath the Hume Highway, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 631–640 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By I Gipps

Each of us has a vision of what the future mine will be and, generally, these visions have many similarities and some differences. One of the major discrepancies in visions of the future mine is not the ultimate goal but the path to achieve it. Many of the future concepts require a radical re-thinking of how things are and will be done yet. So how do we reach this visionary future mine? We need a path that satisfies both our future aspirations of a high tech gee-whiz operated from our iPads and the unfortunately mundane approach that says ‘we must know the method works, ie nothing new’.This paper explores how, within a research based organisation, we firstly set our ultimate goal and then divide the path into realistic technology development chunks that would appeal to mining companies to progress within their organisational constraints. Through examples, such as, automated LHDs, communications systems, surveying and localisation, rock cutting and geological sensing, we illustrate how this path will get us from the here and now to the out there future.This paper also demonstrates CSIRO’s short, medium and long-term research in many of the areas needed to create the Future Mine: mining methods, automation and remote control, mine communications, mapping and mission planning, geological sensing and, importantly, human-system integration, which examines how to effectively present data as information to operators and supervisors in an intelligent and useful manner.

Nov 22, 2011