Search Documents

In 1985 BMR assessed Australia's economic demonstrated resources of mineral sands as follows: rutile 8.0 Mt, ilmenite 41.4 Mt, zircon 11.5 Mt, and monazite 229 000 tonnes. These resources are located along the east coast of Australia, in the southwest corner of Western Australia, and in the Eneabba region, north of Perth, WA. However, over 40% of Australia's rutile and zircon resources, particularly those on the east coast, are presently not available for mining because of environmental considerations. As well, east coast ilmenite has been considered unsuitable for use by sulphate route pigment producers because of its relatively high chrome content. World demonstrated resources of rutile and zircon are estimated by BMR as 29 Mt and 38 Mt respectively. Demonstrated resources of ilmenite amount to about 1 billion tonnes. These occur predominantly in hard rock deposits in Norway, Canada, USSR and China, as well as alluvial deposits in Australia, South Africa and India. Quantitative data for world monazite resources is sparse. However, world production of rare earth oxides is now mainly from bastnaesite, a hard rock resource. Australia is presently the world's principal producer of rutile and zircon, and also provides a major share of the world's ilmenite. With the expected increase in Australia's rate of output of these commodities, combined with restrictions on mining along parts of the east coast, its position could diminish substantially over the next 25 years.

Jan 1, 1986

Results of investigations on adsorption and desorption of CO M CH and a mixture of the two gases are described.4 Results showed that even when the equilibrium conditions contains 50% Co and 50% CH4, the gas emission in the initia' stages will contain as much as 80% CH . 4 The temperature has a small effect and so also particle size for 1.4-11.2mm. The ratio of CO2/CH gases adsorbed in coal samples depends upon t4he equilibrium pressure and this ratio decreases with pressure. Results of field tests support laboratory studies.

Jan 1, 1988

By Muller GP, van Deventer JSJ

A mineralogical analysis has shown that in the Hartebeesfontein ore studied, uranium is associated mainly with uraninite, sulphides such as pyrite and to a lesser degree carbonaceous material such as thucolite. Little could be learned from the literature regarding the mechanism of flotation of these uranium-bearing minerals. A wide variety of reagents were used so that conditions enhancing the flotation of either the sulphides, carbonaceous material, oxides like uraninite, or combinations thereof, were created. As could be expected, the xanthate based floats gave-better selective recovery of sulphides than oleic acid. A substantial fraction of the uranium is associated with pyrite, so that addition of oleic acid to a xanthate float did not enhance the recovery or grade of uranium. After a pre-leach with sulphuric acid in which the pH and Eh were controlled so as to destroy the uraninite, higher uranium recoveries were obtained for the combined float (xanthate, DTP and oleic) and the DTP float. This was most evident when iron was added before flotation. Roasting, which destroyed the sulphides and thucolite, caused a significant decrease in uranium recoveries. The uranium liberated in this way was obviously not flotable in the same way as the uranium liberated from uraninite. A small amount of iron (2 kg/t) added before milling resulted in slightly higher grades and recoveries of sulphur for xanthate based floats. Higher iron additions had a detrimental effect on sulphur recoveries. Even in the case of oleic acid the addition of small amounts of iron had a positive effect on the recovery of sulphur and uranium.

Jan 1, 1993

The Gympie Goldfield was the sixth largest producer of gold in historic terms in Australia. The Joint Venture Agreement between BHP Gold Mines Limited and Devex Limited was signed in January 1987. Since that time, some $20 million have been spent on underground and surface exploration work in the southern portion of the goldfield. The project is of considerable interest as the dewatering, rehabilitation and equipping of an old rectangular timber-lined shaft has been undertaken. The project is located in Gympie, a city of 10,000 people. The issues of dealing with urbanisation and associated environmental aspects are vital to the success of the project. An outline of the project and the geology of the mineralised structures follows:

Jan 1, 1989

By R Zhang, X Huang, M Zhou, X Lv, C Bai

Iron ore sinter accounts for a large proportion of blast furnace ferrous burden in Chinese steel mills. Depleting high-grade iron ore resources and spreading complexity of iron ores in mineralogy and morphology have made it more difficult to utilise iron ores efficiently and economically. In this paper, the physical properties of iron ore particles were characterised using mechanical sieving, laser sizing and gas adsorption. From those measurements, two physical indices (fractal dimension of the particle size distribution and surface morphological factor) are defined as important variables for optimising the granulation performance of iron ores. The moisture capacity and the contact angle of iron ore particles with water were also measured to determine the strategy of water-feed in the granulation process. It can be concluded from the experimental results that an increase in the fractal dimension of the iron ore particles will lead to a better granulation performance, while an increase in moisture capacity with a range of 12.8 ~ 14.8 per cent would increase the optimum water content where the granule packed bed achieves its best permeability. Furthermore, the optimum permeability varies inversely with the moisture capacity of the sinter mixture.CITATION:Huang, X, Lv, X, Zhang, R, Bai, C and Zhou, M, 2013. Iron ore characteristics and their application in optimising the granulation process, in Proceedings Iron Ore 2013 , pp 261-268 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

The key to the successful debt funding of a new mining project, whether in economically established or developing nations, is the submission of a comprehensive feasibility study. The feasibility study forms the basis from which the resource banker can construct financial models which govern the amount of available funds, the conditions which control the supply of such funds and the time period over which the loan may be repaid. The bank will wish to ensure that the feasibility study is the best representation and confirmation of reality possible because this model is the basis of the loan security package. Thus the study will be vigorously interrogated by independent experts in all its elements including the ore reserve, mineability, metallurgy, operating and capital cost profile, environmental factors and management.

Jan 1, 1995

By Chitombo G. P, Thompson A. G

Excavation engineering involves three key design processes; excavation design, blast design and reinforcement design. An excavation engineering methodology is proposed in an attempt to promote integration and simultaneous consideration of these three design processes. This methodology requires research and development of, inter alia, a universal rock mass classification system and a universal data display system. Simple examples are used to explain and illustrate the concepts central to these components in the three design processes.

Jan 1, 1995

In taking the chair at this meeting of the Australasian Institute of Mining Engineers, I feel it my duty to thank you for the honour you have conferred upon me by electing me President for the current year, especially as Bwken Hill is the birth place of the Institute and myself one of its foundation members. I will now endeavour to entertain you for a short time with a few reminiscences of Broken Hill from its inception. Beyond the fact that the mines on the Broken Hill lode have paid to their shareholders in dividends and bonuses no less a sum than £896,500, created and maintained a city of 25,000 inhabitants. supplied a large proportion of the revenue on the railways of a sister state, and made their influence felt throughout the 'commercial centres of the world, very little, I regret to say, is known by the general public as to the form, extent, or vastness of the ore bodies, or the mode of occurrence of the various classes of ore which have been found to exist in them. It has occurred to me that a short paper by the senior mining manager on the line of lode might prove interesting. There has been great difficulty in getting some of the figures relating to the field, the total output of metals from the Broken Hill mines not being obtainable from the Mining Department in Sydney j but an inscription on the foundation stone of the Technical College recently opened in this City, sets forth that the Broken Hill Mines started in 1880...

Jan 1, 1903

This paper gives a first-hand account of what a graduate mining engineer can learn by visiting Atlas Copco in Sweden and gives reasons why all mining engineering students should apply for this excellent scholarship. It will also (attempt to) refute the authorÆs mine managerÆs claim that the trip was a huge junket.

Jan 1, 2006

The Elura Orebody consists of a number of parallel, vertically oriented pipe-like structures of pyrite-sphalerite-galena mineralization located at the core of a structural dome. Concentric zoning of the mineralization into an outer Siliceous, intermediate Pyritic and inner Pyrrhotitic Zone has been previously recognized and is used in routine geologic modelling of the lead, zinc and silver grades.Statistical analysis of the metal grade distribution in the orebody has confirmed the importance of the mineralogical zones in the understanding of grade trends. The gradational nature of intra-zone boundaries, especially those related to the subjective definition of the Siliceous Zone, are apparent in the statistics.

Jan 1, 1990

By Thirumalai K, Peluso R. G

The United States has more than 45 billion tons of economic coal reserves in seams above 10 feet thick and current underground production from thick seams represent less than three per cent of the total production. A tripling of underground production from thick seams is necessary within the next 10 years to meet U.S. coal production demands. An analysis of underground accident and production data is presented in the paper. A study of accident and injury distribution in different coal seam heights in the eastern and western part of the United States in seams ranging in thicknesses from 5 to 15 feet indicates that the seam thicknesses do not produce adverse impact on underground injury incidence. Accidents associated with roof falls and haulage account for about 70 per cent of underground mining injuries.

Jan 1, 1976

By Porter I, Singh RN

An advanced elasto-plastic finite element model adopting a modified Von Mises yielding criterion was used to simulate progressive failure of the rock strata surrounding a room and pillar mine structure. The model conformed to the strain-softening behaviour of rock and accounted for post-failure residual strength. The simulation was achieved in such a way that material values were updated after each FE run, according to the stress criterion until the solution reached the final equilibrium steady state of the mine structure. The suggested structural stability analysis approach accounted for the main features of the structure degradations produced during loading through changes in rock material stiffness and subsequent evolution of stresses. Comprehensive parametric analysis was performed and the inevitable effect of interaction of the roof, pillar and floor on the overall mine stability limit was investigated. The numerical results clearly showed that linear models could not realistically represent the true behaviour of the mine structure. The results obtained are in good agreement with that predicted in the field.

Jan 1, 1992

By Ruston R

When coal mining first commenced in Australia, the principle objective was low cost production with development directed toward recovery of 'easy' coal. Future expans- ion of these early mines into major under- ground operations was neither envisaged nor planned. As the demand for coal grew, these mines were expanded to increase output. however, the absence of initial ventilation planning brought about ad hoc systems wh;ch required continual repair and upgrading. These systems proved satisfactory in the short term because the majority of undergrouni coal mining operations were carried out at relatively shallow depths where gas emission rates were low. By comparison, coal is now being won at depths exceeding 500 metres with a corresponding increase in gas flow from the working seams and adjacent strata. The following paper addresses, firstly, the planning and institution of a ventilation system in a mine where previous inefficiencies were many, and secondly, the value of pre- planning a mine ventilation system in the early stages of mine development, and the need to continually review and upgrade the plan to account for unforeseen ^hanges.

Jan 1, 1983

By P J. McCarthy

Globalisation and consolidation is resulting in the mining industry coming to be dominated by a small number of very large companies seeking to lever assets and knowledge to create wealth. As an important service provider to the mining industry, the minerals tertiary education sector needs to understand these global drivers and respond to them. However, it is under-resourced and its sustainability is under challenge in all Western countries. Through the establishment and funding of the Minerals Tertiary Education Council (MTEC), the Minerals Council of Australia (MCA) has provided a unique opportunity to build a national, world-class minerals tertiary education environment in Australia that can be sustained in the long-term. This paper reviews how the global changes occurring in the mining industry provide the model for what needs to occur in the minerals education sector and how MTEC is the logical vehicle to facilitate these changes. It concludes by suggesting that the time has come to integrate the minerals tertiary education providers into one business. Furthermore, the vision should be for a global mining education academy based around a virtual university capable of servicing the cultural diversity and continuing education needs of the global minerals industry.

Jan 1, 2001

By Crawford G. R, Wold M. B

The application of the hydraulic fracturing technique to the measurement of in situ rock stress from underground excavation is discussed; including relevant theoretical considerations, equipmenl details, experimental technique and analysis procedures. Examples of the application of the technique at three Australian coal and metalliferous mining operations are given. The results obtained from these applications are compared with corresponding results obtained from overcoring tests conducted in close proximity at each site. Generally good correspondence in a wide variety of rock types is indicated. Experience gained with hydraulic fracturing at several underground mining sites has indicated it to be a quick, cost effective means of gaining an understanding of the in situ stress field in sufficient detail for many mine planning functions.

Jan 1, 1990

By Bearman R. A

The majority of published material regarding the operation of crushing machinery is concerned with simulation of performance rather than design of equipment. The reason underlying the bias in published material relates to why research is carried out and who undertakes the research. Two distinct types of research can be identified: 1. Internal research by crusher manufacturers - generally related to mechanical design, value engineering and to the commercial realities attached to sales demands. Any work on basic crusher geometry or rock/machine interaction is of a sensitive nature and rarely enters the public domain. 2. Academic research - mostly confined to modelling of crusher performance and simulation. This is not because of any bias, but crusher design requires access to manufacturers data or at least an in-depth understanding of crusher design, which is rarely available. The crushing of rock is a complicated problem. It involves three aspects; the machine geometry, the material composition (type of rock/feed size distribution) and the machine/rock interaction. The machine geometry is often ignored in empirical mineral processing simulations, while the response of different feed materials is only nominally addressed in machine specifications provided by manufacturers. The manner by which the machine produces a stress field and causes different types of breakage for different rocks (or the machine/rock interaction) is sadly neglected by both groups. All three aspects must be considered collectively to successfully understand and model the entire crushing process. 1. Centre for Mining Technology and Equipment, Julius Kruttschnitt Mineral Research Centre, University of Queensland, Isles Road, Indooroopilly 4068 Qld. The importance of crushing is often underestimated. In mining and mineral processing the invisibility of the crushing process is understandable as it merely provides a coarse reduction stage prior to the intricacies of mineral extraction. However in the quarrying industry crushing and screening basically provide the finished product. A brief overview of the quarrying industry shows the importance of crushing. Figure 1 gives production figures for most of the western European countries, Australia and the USA.

Jan 1, 1995

The treatment of the Broken Hill ores has,undergone many changes during the last ten years, and it may be of interest to some of the members to know what are the main lines on which the Proprietary Mine works at present. It must be understood that the want of absolute uniformity in the treatment amongst the various mines at the Barrier does not prove that some of the mines are working on wrong lines, for the ore is not exactly the same along the whole line of lode; this necessitates a variation in treatment, although generally only in detail.At the Proprietary Mine the ore is all mined by contract the miners are paid so much per ton for clean ore. The ore in the mine in most stopes is mixed with gangue, and the inclination of the uliners is, of course, to mix gangue with the ore, so as to be paid for as large 3 tonnage as possible. This is quite natural clean ore is easily distinguishable from clean gangue, but most lumps are a mixture of clean ore and gangue in varying proportions. The miner will naturally throw into his heap pieces which he considers still good enough, whilst the management may consider these pieces just a trifle too poor; consequently a check must be kept on this.This necessitates the first operation to which the ore is submitted. 'The trucks tare 51 cwt.; average load 21 cwt.), as they are loaded underground, have a ticket attached::showing to whiyh contract they belong on arrival at the top of the shaft they are passed over a weigh bridge...

Jan 1, 1907

By Clements R. J, Davey J. M

Development of the process from the pilot stage to the current operation of the Capel, W.A. plant is briefly described. The design criteria for a larger sized plant are discussed together with factors that relate suitable feedstocks and coal types to the capital cost, capacity and product grade of future plants at locations other than Capel. The application of the process to the direct reduction of iron ores is briefly discussed including its commercial application at Rockwood, Tennessee.

Jan 1, 1979

By Wright R. J

The Commission called tenders for a four boom hydraulic jumbo, plus basket, on an art- iculated carrier in Sept. 1977. Atlas Copco submitted the successful tender in Jan. 1978 for the supply of a three boom jumbo, plus basket. The Promec TH470 jumbo was commiss- ioned in the 2000 m long Sophia tunnel in Nov. 1978. Adequate spare parts were not available during the first three months of operation and the hammers could not be overhauled at the recommended interval. One hammer was removed after drilling 13 600 m due to a crack in the intermediate housing. Tests were conducted with different types of drilling consumables. Both rope and Hi-teed threads were tested and found compar- able. The average penetration rate in the granite was 1.1 m/min. Initially the drillers were not experienced enough to operate the BUT 15ERH booms without causing damage to the booms and hoses. Drilling deviation espec- ially of the perimeter holes was greater than expected. It is now obvious that greater attention must be given to attracting, train- ing and retaining the right type of operator and maintenance fitter.

Jan 1, 1981

An assessment has been made of six reported methods for the determination of the swelling of iron ore pellets on reduction. The methods are discussed on the basis of apparatus requirements, reduction conditions, sample requirements, measurement of swelling and reproducibility. It is concluded that the CNRM, LKAB, and Lurgi methods are the most satisfactory which presently exist for determination of the swelling of industrially produced, iron ore pellets.

Jan 1, 1974