Search Documents

Black coals occur in most of the major sedimentary basins in Australia. In addition to the better known Permian coal occurrences of the Sydney, Bowen, Oaklands and Galilee Basins, coals of Permian age occur in the Arckaringa Basin in South Australia, the Bonaparte Basin in Northern Territory and the Collie, Perth and Canning Basins in Western Australia and the Tasmania Basin in Tasmania. Coals of Triassic age occur in the Ipswich Callide and Tarong Basins in Queensland, the Tasmania Basin in Tasmania and the Leigh Creek area in South Aus- tralia. Coal bearing rocks of Jurassic age occur in the Mulgildie Basin and Maryborough Basins in Queensland and in both the Queensland and New South Wales portions of the Clarence Moreton Basin and Surat Basins. They also occur in the Perth Basin in Western Australia. Rocks of Cretaceous age known to contain coal occur in the Styx, Maryborough and Laura Basins in Queensland, the Gippsland Basin in Victoria and both the Queensland and New South Wales portions of the Surat Basin. The coal measures have been deposited in a variety of sedimentary environments and the coals vary widely with regard to thickness, extent, banding characteristics, maceral and ash content. However, they are generally of low rank and most are suitable only for steaming.

Jan 1, 1975

By Bloom M. S

Epithermal vein and breccia hosted Au mineralisation at the Kerimenge prospect, in the Wau district, Papua New Guinea, occurs within a block of multiply fractured dacite porphyry of Pliocene age, and is localised on intersecting regional fault structures, marginal to the eroded vent of a Late Pliocene-Pleistocene maar volcano (diatreme).Au mineralisation is primarily controlled by the steeply dipping Kerimenge Fault zone, which hosts a basal zone of silicified breccias,transitional laterally and vertically to networks of fracture controlled veins.Early quartz+pyrite veins, deposited from CO2 rich, NaCl saturated, boiling fluids pre-date the main phase of Au mineralisation. Four stages of Au bearing vein mineralisation have beenrecognised. Quartz+sulphide veins (stage 1) and partially coeval quartz+sulphide+carbonate+ adularia veins (stage 2) occur marginal to silicified breccias, and are associated with quartz+sericite+pyrite wallrock alteration. Similar depositional conditions prevailed for stage 1 and stage 2 mineralisation. Mineralising fluids underwent two stage boiling at temperatures of 145 to 2300 C. Boiling resulted in the loss of approximately 3 wt.% CO to the vapour phase. 2 Fluid salinity was probably I wt.% NaCl or less.

Jan 1, 1990

Pillar mining methods at the Pasminco Mining Broken Hill Operations are not new. Since mining commenced on Pasminco's leases at the turn of the century virtually every pillar extraction method tried throughout the world has been used. Much of the remaining mineral resource in the Pasminco Broken Hill leases is contained in pillars.However, due to the on-going need for mechanisation with bulk mining methods, and the very peculiar physical circumstances surrounding the formation of these pillars, their exploitation requires the development of a virtually new method based on excavation technology not previously used in the Australian mining industry. Trials of the method are to take place at the southern operations during 1991.

Jan 1, 1992

By D T. Ribeiro, J F. C L Costa, J C. Koppe

Drilling and sampling are responsible for most of the costs during mineral exploration, especially in multi-elements and polymetallic deposits, such as iron, manganese and bauxite deposits. On these deposits, often it is necessary to estimate multiple attributes at several granulometric fractions, ie distinct particle sizes. This paper investigates the effect of sampling at a close spacing grid only the head grades for the multiple chemical species in iron ore deposits. The remaining required data at the various grain sizes are sampled at a sparse grid. The derived geological model is checked for precision and accuracy comparing the output obtained against a model obtained using a complete isotopic data set including head grades and chemical analysis at each granulometric fraction analysed at all sampled positions. Among the several tested alternatives, the best procedure for dealing with the posed problem involved utilising the correlation coefficients between the grades at distinct fractions to obtain an isotopic database prior to interpolation. Cokriging was the method used, based on the intrinsic coregionalisation model. Estimates were obtained with the quality needed for the proposal of the study. Results showed that at least 50 per cent of the blocks were estimated with errors less than ten per cent relative to the grades obtained at the reference model, using only 15 per cent of the granulochemical data employed to obtain the reference model. The methodology also preserved the correlations between the attributes in their several granulometric fractions on the estimated model.

Sep 26, 2011

By N McKenzie, E Taylor, S V. L Barrett, H Lagger, A Purwodihardjo

This paper discusses the temporary support design methodology for the largest road caverns ever built in Australia—the Lutwyche Caverns—part of the Airport Link project in Brisbane, Australia. The Lutwyche Caverns with a maximum excavated span of 27 m form a key component of this major road project, allowing on and off ramps merging with the underground highway. In addition to the two large span caverns, a 15 m soft ground tunnel with 5 m cover above the caverns and two 24 m deep burial chambers for the 12.4 m tunnel boring machines (TBMs) had to be built in record time at Lutwyche.The temporary support design methodology involved the use of a range of analytical approaches, including empirical methods to provide a starting point for design development, key block models to determine the potential influence of discontinuities on excavation stability and 2/3D continuum and discontinuum models to determine the potential influence of adjacent excavations and the proposed construction staging on the design. In addition, probabilistic analysis of potential kinematic instability using a discrete fracture network (DFN) approach was also undertaken to establish the critical block loads for the temporary lining, while the continuum and discontinuum models were used to design the support for the 1.5 m diameter rock pillar at the north end of the northbound cavern.The numerical modelling was undertaken in close conjunction with the contractor to develop the optimal construction sequence, considering the available construction equipment on-site and the overall project program requirements. Part of the presentation will further show the applicability of the developed design during construction (deformations, monitoring field observations) and lessons learned for future cavern construction in Australia.CITATION:Lagger, H, Purwodihardjo, A, Barrett, S V L, McKenzie, N and Taylor, E, 2014. Temporary support design for the largest road caverns ever built in Australia – the Lutwyche Caverns, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 399–410 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By W Valery, A Jankovic

A growing demand within the minerals industry for sustainable development and the introduction of carbon taxes have resulted in a significant focus on improving the energy efficiency of comminution circuits. However, in this drive for improved energy efficiency the role of classification has been overlooked. Inefficient classification and large recirculating loads reduce circuit capacity, result in over-grinding and higher specific energy consumption.It is well understood that classification increases mill capacity; therefore, closed ball mill-cyclone circuits have become an industry standard. However, due to limitations in cyclone classification efficiency, the optimum recirculating load is limited to about 250 per cent. A simple relationship quantifying the effect of classification efficiency and recirculating load on grinding circuit capacity is presented in this paper. The possibility of improving the capacity of ball mill circuits by improving classification efficiency is discussed, considering the current practical limitations of classification equipment. Simulation tools were used to evaluate circuits with cyclones and with high frequency screens to identify opportunities to improve energy efficiency. The investigation also identified potential benefits to flotation recovery due to a reduction in over-grinding.CITATION:Jankovic, A and Valery, W, 2012. The impact of classification on the energy efficiency of grinding circuits - The hidden opportunity, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 65-70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By C Bartle

In many operations the use of less electrochemically reactive grinding media in the first grinding stage (for example, rod milling and high aspect ratio SAG milling) is rarely considered. Therefore, in reality a plant may inadvertently be using a 'mixed' media charge. That is, whilst employing inert grinding media during secondary grinding, electrochemically active forged steel grinding media may be used in the primary grinding stage. This paper discusses the impact of such a circuit on the pulp chemistry and flotation response of a refractory gold ore. The Wiluna concentrator has two grinding circuits operating in parallel. Line 1 operates a single ball mill in closed circuit with cyclones, and utilises high chrome grinding media, while the second circuit (Line 2) consists of a rod mill (with forged steel rods) in series with a ball mill, which also utilises high chrome grinding media. The cyclone overflows from both circuits are combined to feed a sulfide flotation circuit. Pulp chemistry surveys were completed around both grinding circuits, and laboratory flotation tests were conducted on the cyclone overflows. The results demonstrate clearly that the rod mill/ball mill circuit operated at significantly lower Eh and dissolved oxygen values, while the percentage EDTA extractable iron was considerably higher, when compared to the single stage ball milling circuit. These variations in pulp chemistry had a marked negative impact on the laboratory rougher flotation response, and suggests that plant performance may be affected.

Jan 1, 2008

By A Hughes, J Agius, T Ferguson, A Parbhakar-Fox, D Lester, L M. Jackson

Management of historic tailings is a major challenge facing the mining industry and its regulators. However, through improved mineralogical and chemical characterisation of such materials the opportunity to develop better rehabilitation strategies arises. Microanalytical techniques including microscopy, mineral liberation analysis and laser ablation inductively coupled plasma mass spectrometry (ICPMS) allow for improved tailings characterisation – but the challenge posed by these techniques is how to use them effectively. Additionally, data sets collected by such techniques must be properly integrated, only then can they assist in the identification of the most appropriate rehabilitation strategies. A study conducted at the Old Tailings Dam (OTD) located at the Savage River Mine, Tasmania allowed for the integrated use of several microanalytical techniques to help evaluate the benefits of a shallow water cover as a potential rehabilitation strategy. Samples (n = 144) from 14 trenches and 11 boring cores (2 m maximum depth) were collected across the OTD. These were subjected to routine acid-base accounting, with a subset subjected to detailed mineralogy using a modified sulfide alteration index (SAI), X-ray diffractometry and mineral liberation analysis (MLA). In addition, representative samples (n = 6) from across the OTD were subjected to laser-ablation ICPMS to characterise the pyrite chemistry. Our results showed that tailings in the northern area submerged under a natural water cover were relatively unoxidised from approximately 1 m depth, with SAI values of 1 to 2. Tailings from the subaerial southern portion were extensively oxidised to approximately 35 cm depth (SAI = maximum 5.8), with fresher materials observed underneath (SAI = 5 to 5.8). Pyrite from across the OTD is enriched in Co, Cu and Ni. Through the integrated application of microanalytical tools, we determined that establishing a water cover of at least 1.5 m depth across the OTD is a suitable rehabilitation option for this historic site. However, consideration for the reprocessing of these tailings to extract Co should be further investigated.CITATION:Jackson, L M, Parbhakar-Fox, A, Hughes, A, Agius, J, Ferguson, T and Lester, D, 2015. Microanalytical evaluations of the savage river old tailings dam, north-?west Tasmania, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 111–124 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By Mould GR

Gas drainage has been practiced for many years mainly for safety reasons in various countries in Europe, in the U.S.A., the U.K. and Japan. Legislation has been developed to control the production, transport- ation and utilisation of methane and associated gases. Gas drainage is now being carried out at some Australian Collieries, but as this is a new venture little specific legislation is available. This paper briefly describes the drainage methods and legislation applied overseas, gives a brief history of gas drainage in N.S.W. and indicates the deficiencies of the present legislation. It outlines the approach to new legislation which will deal comprehensively with gas drainage operations and utilisation in New South Wales.

Jan 1, 1982

By G J. Harbort, K Lam, C Sola

The relationship between the geology of porphyry copper deposits and their processing performance is an area of interest. Being able to predict comminution properties of the ore from physical characteristics and geological descriptions would allow an increase in the precision of capital cost estimates, operating cost estimates and throughput rates. This geometallurgical approach would reduce the requirements for expensive comminution tests.As the comminution circuit is the highest capital cost item in the plant and a possible throughput bottleneck, understanding the variability in hardness within the orebody is critical. A geometallurgical model allows calculation of ore hardness values in mining blocks from ore characterisation data. This model subsequently uses a combination of simulation and power-based approaches to relate ore hardness and flotation feed size to grinding circuit throughput.This paper reviews the geometallurgical models developed for seven porphyry copper deposits and discusses the strengths and shortfalls of the methodology and similarities and differences between the different deposits.CITATION:Harbort, G J, Lam, K and Sola, C, 2013. The use of geometallurgy to estimate comminution parameters within porphyry copper deposits, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 217-230 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

Gold is actively precipitating at grades up to 80 g/tonne at and near the surface of the Waiotapu geothermal system, located in the Taupo Volcanic Zone of New Zealand. Many characteristics of this active system makes it analogous to the environment deduced for epithermal precious metal mineralisation in the circum Pacific region.The near surface area of the geothermal system is approximately 17 km2, caused to an extent by the upflow of deep, neutral pH fluids being deflected into a lateral flow of several km. This fluid has pervasively altered the rhyolite pyroclastic and ash deposits to an assemblage generally characterised by the term propylitic; major vein mineralisation is not observed. The temperatures at the 1100 m limit of drilling are 300¦C, and decrease to the surface along a boiling point curve.Condensation of steam and H S (subsequently oxidised) at the surface (derived 2from deep boiling) results in the formation of heated acid sulphate waters. These have caused a shallow (50 m) cap of advanced argillic alteration. Mixing of this oxidised condensate with the deep neutral pH fluid appears to be the principle cause of gold deposition from thiosulphide complexes. The major focus of gold mineralisation is in Champagne Pool, a hot spring which fills one of several 900 year old hydrothermal eruption craters.

Jan 1, 1984

The recovery of Copper by solvent extraction was arguably the most significant hydrometallurgical development of the 1960's. However, only dilute solutions at relatively high ph. could be treated effectively. ICVAcorga introduced in the 1970's the much stronger salicylaldoxime based reagents, which resulted in a dramatic change in plant configurations. So for example plants which normally use 3 extraction stages and 3 stripping stages could be reduced to 2 + 2 staging or 2 + 1 staging, even for high copper tenors at low ph. Leach liquors up to 40 g A copper are being treated at some locations so that almost any copper bearing liquor can now be purified by solvent extraction. Following a considerable amount of research and development effort ICI/Acorga have made further significant advances in the application of copper solvent extraction. The first of these is in computerised flowsheeting. In conjunction with ICI's Process Technology Department, Acorga have developed the Minchem Computer program, which uses laboratory generated equilibrium data to facilitate optimisation of metallurgical operating parameters. The program can operate in two modes, prediction and assessment so that given suitable extract and strip isotherms plant performance can be predicted for a given set of conditions. Alternatively existing plant performance can be assessed rapidly and accurately, thus providing a valuable quality control tool. Pilot plant work can now be restricted to evaluation of the physical aspects of the SX circuits, and to looking for the unexpected. Secondly using the patented 5-Nonyl Salicylaldoxime in precise admixture with a number of carefully selected strip modifiers, the Acorga M-range has resulted. Reagent selection from these new extractants can now be based on how the reagent can alleviate the remaining problems such as hydrolytic stability, transfer of iron, and organic losses by entrainment which may be related to particular features of the operating plant. Thus the Acorga M-range has enhanced and significantly extended the use of solvent extraction for copper, whilst refinements in the processing of metallurgical data has considerably simplified circuit design and analysis of results.

Jan 1, 1989

By P J. Hawke, M F. Flis

The Hamersley Basin of Western Australia holds significant tonnages of detrital iron deposits. Formed by a cyclic weathering and eroding sequence of nominally barren banded iron formation, they may form rich proximal accumulations of iron cemented gravels distal from any obvious hard-rock iron mineralisation. While generally small, they nonetheless represent excellent economic targets as they are near surface and easy to mine. The relatively high density of iron detritals, when compared with their sedimentary hosts, makes the gravity method the primary method of exploring for these blind deposits. Identification of possible trap sites is used as a precursor to gravity surveying, with magnetics used as an ancillary method prior to drilling. Application of the gravity method in this terrain is not straightforward. Detrital trap sites are best developed next to the spectacular cliffs that form the range fronts to the Hamersley Ranges. Precise terrain corrections and use of first vertical derivatives are routinely applied to gravity data in an effort to map every possible gravity high that may reflect the presence of a detrital accumulation. Extensions to Hamersley Iron Pty LimitedÆs BS2D deposit were discovered by the routine application of gravity. This methodology has been used to create a model by which exploration for detrital deposits continue to the present day.

Jan 1, 2002

By F K. R Klose

Malmberget is a sublevel caving mine owned and operated by Luossavaara-Kiirunavaara Aktiebolag (LKAB), a Swedish state-owned iron ore mining company, in northern Sweden. The mine has an annual iron ore production of approximately 15 Mtpa. The current strategy foresees an expansion which will increase the mine’s depth considerably. Ventilation and air conditioning modelling for the planned expansion is ongoing. One of the most influential parameters for ventilation planning anddesign for a deep mine is geothermal gradient, which is crucial for the design of the refrigeration system. It is determined through virgin rock temperature (VRT) measurements carried out at various depth below the surface. This paper details these measurements and the determination of geothermal gradient for Malmberget Mine for the expansion study, which were necessitated by thelack of information for the focus depth and area.

Oct 12, 2022

By J Jardine

An improved ground support method for development intersections, wide spans and stope brows was implemented at Kanmantoo mine. The method uses a jumbo to simultaneously drill and install self-drilling anchors (SDAs) to depths from 4.5 m to 7.0 m. Resin is subsequently pumped into each SDA using a specially designed integrated tool carrier basket, with plating occurring within 10 mins due to rapid resin cure. This methodology means that SDAs can be installed rapidly due to reduced process steps and wait times with reduced hazards to personnel. Cablebolts are used extensively in underground mines to reinforce the ground in wide spans, such as at intersections and stope brows. The flexible cablebolt tendon allows for a long, continuous and high-capacity reinforcing element to be inserted into the rock. A common cablebolt installation practice at Australian underground mines that do not utilise a mechanised cable bolter, is for cablebolt holes to be drilled by a jumbo or longhole rig, hand installation and grouting by a service crew, then plate tensioning following a grout curing wait time of typically 12 to 24 hours. This process involves multiple separate labour-intensive work processes and results in reduced availability of priority headings. This paper discusses the development history of vertical SDA use in wide spans at Kanmantoo mine. The installation process is fully described, including aspects such as reliable in-hole coupling of SDAs, resin selection and pumping aspects. A cost benefit assessment, and a case for ground stability are presented to compare cablebolt use to SDAs in development intersections.

Mar 29, 2023

By A Lines

This paper addresses a gap in longwall multi-seam interactions and their predictions, providing a case study for future multi-seam operations for both anticipated conditions and a method for understanding the changes in stress regime. Multiple panels were modelled with the results analysed and compared to panel experiences to validate the parameters and properties. The software chosen (LaModel) is a numerical modelling package designed to model stresses and displacements on thin deposits. It utilises a displacement-discontinuity variation of the boundary-element method and has been used extensively throughout both the United States and Australia in multi-seam operations. Analysis of the results demonstrates a clear correlation with the above workings and regions of significant strata instability. This provides the opportunity going forward to analyse new models and incorporate into mine planning and geotechnical designs. Continuous site-based assessment should be undertaken at multi-seam operations to better understand and quantify likely vertical stress levels within the workings. With a detailed analysis of models prior to extraction and a review of models post extraction. Further research is required as LaModel is limited to vertical stress and it is likely that interactions impact both the horizontal and shear stress regime. 3-dimensional modelling could further assist in this understanding, combined with a thorough stress monitoring regime. CITATION:Lines, A, 2018. Modelling multi-seam interactions for longwall mining, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 185–195 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Radmuller H

The proposed underground mine at Porgera forms an integral part of the Porgera Joint Venture project in Enga Province in the remote Highlands of Papua New Guinea. The total in-situ reserves are approaching 400 tonnes of gold making the Porgera deposit one of the largest in the world. The remote, rugged and inhospitable terrain, recent unstable geological environment and primitive yet socially complex nature of the densely populated local community, combine to make the Porgera project very different to developing mines in Australia. The Porgera project is a challenging and exciting mining exploration venture in the final stages of feasibility study submission and negotiations with the National Government of Papua New Guinea. A 1476 m exploration adit was driven in the footwall of the high grade mineralisation for diamond drilling purposes as part of the evaluations necessary for the feasibility study. Ground conditions encountered have ranged from weak mudstones with high water content, requiring immediate steel set support, to competent intrusives.

Jan 1, 1988

By M Barker, H Li

The total number of tailings accidents has reduced from over 50/decade in the 1960s-1980s to less than 30/decade in the 2000s to 2010s. However, the rate of significant tailings dam failures has not been reduced. The significant tailings dam failures the mining industry experienced in the recent history include: Merriespruit, South Africa, 1994; Los Frails, Spain, 1998; Kolontár, Hungry, 2010; Mount Polley, Canada, 2014; and Samarco, Brazil, 2015. The conventional Factor of Safety approach itself may not be enough to further reduce the rate of significant tailings failures due to its limitations such as uncertainty. For example, the same factor of safety could have a vast range of annual probability of failure for different tailings dams, and insufficient consideration of failure consequence. This paper presents a risk based approach for design with the objective being to minimise tailings dam failures, especially those significant tailings failures with high consequence and low probability. This approach includes risk based design and risk management using bowtie tools. In the risk based design, quantitative analysis will be used to estimate the annual probability of failure and the tolerable failure criteria is linked to the consequence category. Bowtie analyses will be used to understand hazards and risks and identify and select independent controls that are effective in preventing and mitigating catastrophic failures. In this paper, examples of risk based design and bowtie analyses are presented and discussed. CITATION:Li, H and Barker, M, 2018. Risk-based approach for minimising tailings dam failures, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 397–414 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By R Lachenicht, J Player, A Thompson, E Villaescusa

Kanowna Belle Gold Mine is a deep, high-stress, sublevel open stoping mine located near Kalgoorlie. Seismic activity during the development cycle presented problems, including concerns regarding the exposure of personnel. A number of seismic management systems were developed and tested to monitor seismicity and control the risk. It was recognised that a dynamically capable reinforcement and support system was required to be installed as part of the development cycle to reduce the risk of exposure of the underground workforce to uncontrolled movement of rock. The performance of a new Garford Dynamically capable bolt was measured in tests performed by the Western Australian School of Mines (WASM) at their Kalgoorlie Dynamic Test Facility. Detailed descriptions of the facility and data processing were reported by Player, Villaescusa and Thompson (2004) and Thompson, Villaescusa and Player (2004). The development of the Garford Dynamic bolt is described and dynamic testing results are presented and evaluated. This bolt was implemented in the mining cycle following the testing program; the observed performance is described and assessed in this paper.  

Jan 1, 2008

By Snowden C. T

B Lens Main is a scheelite orebody with an average dip of approximately 15¦ and thickness ranging from 1.5 to 6.0 m. The orebody is overlain by a banded section of ore and waste which tends to slab off if left unsupported. It was originally planned to mine a large portion of this orebody by room and pillar methods, with existing diesel trackless equipment. This, however, proved unsuitable for a number of reasons and the smaller scale method of slot stoping with hand machines and scrapers was employed. The following major problems were encountered. 1. The method was new to the mine and the work force, and had to be commenced quickly using existing or easily obtainable equipment. This is gradually being overcome by training, modification of procedures and introduction of more suitable equipment. 2. The slabbing from the hanging wall had to be controlled, either by support or by mining this low grade section and accepting the resultant dilution. This has been approached in a number of ways, depending on conditions and the method will have to be further modified as different conditions are encountered in new areas.

Jan 1, 1977