Search Documents

By T Takayama, M Matsumura, Y Konno

The steel industry accounts for 14 per cent of domestic CO2 emission in Japan, and iron ore sintering process occupies approximately three per cent. While Fe content in iron ore is gradually decreasing. So, the amount of concentrated iron ore will increase in the future. We have focused on magnetite concentrate as sinter materials, because magnetite can be easily magnetically beneficiated. However, it is experienced that blending magnetite ore resulted in increasing Fe2+ component in the iron ore sinter, which results in lower reducibility. Therefore, promoting the oxidation reaction from magnetite to hematite in the sintering process is countermeasure for reducibility. In addition, this promotion causes increase of oxidation heat, which results in high sinter strength and reduction of coke. It is assumed that the oxidation of magnetite tends to proceed in the cooling stage, where the oxygen partial pressure increases after the combustion of fine coke, but there are few studies on the effect of heat profile, especially cooling path. The purpose of this study is to design the effective sintering heat profile to promote oxidation of magnetite ore, especially, to investigate the effect of cooling path on sintered ore microstructure. In this study, magnetite ore and magnetite reagent were respectively mixed with calcium carbonate reagent. Then the mixed samples were pressed and formed into cylindrical tablets for simulating the adhesive layer of a pseudo particle. Through examining influence of maximum temperature and cooking rate on oxidation reaction of magnetite, we confirmed that the oxidation reaction of magnetite is suppressed at above 1350°C for maximum temperature, compared to 1300°C. Sintering at lower temperature is desirable because hematite is stable below 1350°C in the Fe2O3-CaO phase diagram.

Nov 8, 2021

By P B. Hills

Increasingly over the past couple of decades, the importance of understanding the in situ stress regime in underground hard rock mines has become accepted by all. Providers have responded to this requirement and various techniques for undertaking the measurements have been honed while others have slipped from use. It is a simple, though not inexpensive task to engage a provider to undertake the require measurements, and a comprehensive report will ensue. So, what has actually been obtained? What should the geotechnical engineer do next? What tools are necessary to do so? Regardless of the method of measurement, the report will describe the location of the measurement site and describe the basis of the methodology used in undertaking the measurements and a log of the measurement program. Finally, it will include the results, which should incorporate the normal and shear stress components of the full stress tensor. Ground control management plans (GCMP’s) and stress summary reports and spreadsheets prepared by site geotechnical engineers always include the magnitude, trend and plunge of the principal stresses. Remarkably few site-based summaries include the full stress tensor. This is a significant gap as the full stress tensor is vital for any further data manipulation. However, without the algebraic tools to undertake those manipulations, their value is diminished. This paper seeks to provide a checklist of ideas to be considered. It provides commentary on the options available to dissect the stress measurement report and ensure that the maximum possible value is derived from it. The manipulation and presentation of component stress data is also discussed. The various methods of stress measurement are not the focus of the paper but some of the strengths and weaknesses of them over which the site geotechnical engineer has some control, are highlighted.

Nov 29, 2022

By G Capes

A novel open stope design approach is presented that delivered improved performance in a mining area with poor ground conditions at the Olympic Dam mine. During 2019, a large open stope had an unplanned caving event resulting in the inability to extract the planned tonnes and subsequent sterilisation of nearby stopes. A design limitation was the lack of data and understanding around the alteration domain extents, the rock mass strength controls and limits, the failure modes controlling stope stability in the local area, and the use of conventional stope shapes. From the available data and failure observations, it was inferred that the dominant caving failure mode resulted from a blocky rock mass impacted by structure and alteration causing an unravelling failure mechanism. Numerical and empirical analyses were conducted to test this hypothesis and establish strength limits for design. The strength limits for the design were then used to provide a range of outcomes from which future stope design shapes such as chamfered backs could be selected. Three alternate chamfered geometries were selected to trial the innovative designs. The application of this methodology in 2020 resulted in overbreak reduction from >100 per cent in the initial caved stope to

Mar 29, 2023

By R K. A Taylor

The growth in production of beneficiated ilmenite products has been one of the most significant trends in the titanium feedstock industry over the past 30 years. In this period, the production of titanium slag and synthetic rutile has grown five-fold to the point where these products represented 56 per cent of total feedstock production in 2000. Additional production capacity is being proposed as the core component of new feedstock supply projects presently under consideration. A high proportion of these products is based on technologies for which the inherent quality of the is an essential factor. Location specific factors also play a large part in determining the cost of production. As the demand for such products grows, and the availability of favourably located sources of ilmenite of suitable quality declines, it can be expected that existing beneficiation technologies will become increasingly constrained. Existing beneficiation technologies, and those which have been developed, but are not yet commercially applied, are reviewed. Future issues which are likely to impact on the cost effectiveness of these technologies, or the quality of final products, are identified. These factors suggest directions for development of ilmenite beneficiation technologies to achieve economic production of the quality of feedstocks which will be demanded by the TiO2 pigment industry in the future.

Jan 1, 2001

By Subrahmanyam T. V, Rao V. D

GOLD, the most important and highly coveted valuable metal, is being sought and exploited in almost all the geological environ- ments by the developed, developing and underdeveloped coun- tries of the world. Brazil, one of the five largest countries of the world, has similar geological and lithological environments as of Africa, Australia and Canada and also produces this noble metal. With the recent gold rush in Serra Pelada Hill in Para State of Brazil and the consequent migration of a large number of enter- prises to the Amazon region in search of geological conditions similar to that of Serra Pelada, the status of Brazil in gold produc- tion has been considerably elevated to be among the first five of the world. The principal geological environments or the lithologies where gold can be explored are the greenstone belts, banded iron for- mations, quartz lodes and placers; and the tectonic controls like shear zones in these horizons, or the tectonic relics or the annular- structures that limit the quartz vein systems in felsic as well as volcanogenic systems and epithermal models. The greenstone, BIF associations are present in all the Archean-Proterozoic ter- rains in Central and Northern Brazil. The quartz boudins in Al rich schistose rocks and the weathered and chemically enriched

Jan 1, 1988

By W R. Adamson

Cerro Vanguardia SA (CVSA), property of AngloGold Ashanti, mines gold and silver from a system of vetiforme orebodies located in the south of the Argentine Patagonia, in the Province of Santa Cruz.Surface mining techniques are applied to develop a series of narrow pits with an average waste to ore ratio of 26:1. This quite unique constraint brings into focus the need to maximise inter-ramp and final wall angles, leading to a strong need to optimise wall control drilling and blasting in order to reduce back-break damage to an absolute minimum.The paper describes a program of applied investigation and design modification implemented during?2008?and?2009 in?two?separate pits of Cerro Vanguardia. Three distinct yet complementary damage mechanisms were identified and observed during the field components of the work; vibration induced strain fracturing, surface cratering around blasthole collars and quasi-static loading and unloading of the surrounding rock mass as a consequence of poorly controlled confinement.With these mechanisms identified, a measurement, modelling and modification campaign was conducted in order to reduce the incidence of each source of damage. Interactive design analysis and modelling, near-field vibration measurement, video capture and the application of electronic initiation technology were supported by seed wave modelling and topographic evaluation of the achieved results.Results point to the usefulness of simulation techniques for determining optimum delay timing to reduce vibration impact, while the visualisation of explosive energy distribution produced by drilling and explosive loading decisions assists in reducing the probability of over-confinement.This paper presents relevant aspects of the two fieldwork campaigns:1) describing the application of the techniques, and2) summarising the results obtained.

Nov 8, 2011

By D Mather, H R. Asche

"In the civil tunnelling field, the use of tunnel boring machines (TBM) has now overtaken the use of conventional excavation methods (drill and blast / roadheader). This is due to a number of reasons, including the increasing availability and reliability of TBMs, the ability to deal with a wider range of face conditions, and the reduced excavation cost that TBMs can bring.Mining companies have spearheaded the advances in shaft boring by mechanised means, both in blind and raise boring. However, mining companies have been slower to adopt mechanised tunnelling.When contrasted with a conventional mining contract, there are good reasons why TBMs in mining applications are relatively rare. A conventional decline contract may have very little geotechnical information. The decline alignment can be subject to change as the tunnelling progresses. The infrastructure requirements are less for a conventional decline, and the sunk cost prior to excavation commencing is lower. Contract documents can be very simple.The history of TBM use in mining is reviewed and lessons are described. From the case histories and lessons learnt, the paper identifies ways that mining companies can maximise the potential benefit of TBM technology.We believe that despite the additional requirements for TBM declines, the cost and time advantage to mining companies is very attractive. The challenge is to recognise and to meet the requirements for success in a TBM drive to achieve the advantages of: faster advance rates reduced rock damage/overbreak reduced support requirements uniform muck characteristics greater personnel safety.From the case histories and lessons learnt, the paper identifies ways that mining companies can maximise the potential benefit of TBM technology.CITATION:Asche, H R and Mather, D, 2014. Use of ?tunnel boring machines in the mine environment, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 655–662 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 17, 2014

By W Z. Liu, Q Q. Shi, H T. Yang, X L. Zhang

In order to improve the cutting blasting effect of dimension stone mining, the water coupling directional cutting blasting technology was put forward. Based on the test apparatus and special charge configuration, the mechanism of directional cutting blasting was analysed. Directional device changes the initial equilibrium of the total energy of shock wave effect on blasthole wall. The initial directional crack first appears in the blasthole wall that makes contact with the directional device. Then, two cracks are connected along the direction of the blasthole centre line under the action of detonation pressure and water wedge. The plexiglass tests showed that water coupling directional cutting blasting technology produced cracks along with the predetermined direction completely. The cutting surface was smooth and only a few short cracks appeared around the blastholes. It proved the validity of this technology.CITATION:Liu, W Z, Zhang, X L, Yang, H T and Shi, Q Q, 2015. Directional blasting rock cutting technology, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 815–818 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By D I. Cliff

The loss of 11 miners in the 7 August 1994 Moura No.2 Underground Mine Disaster was the catalyst for major change in the way safety was managed in the Australian Mining Industry. The impact was felt across all sectors not just underground coal. It was the catalyst for the overhaul of the regulatory frameworks, moving away from prescription to management systems and risk management. This had a substantial impact on the way not only the industry operated but also on how the regulator functioned. It heralded the introduction of competency-based training across all levels of the mining workforce. Since that time major improvements in safety performance have occurred. However, hiding within the statistics are some disturbing trends. This paper aims to analyse the progress made in the past 30 years and identify the current and emerging issues. Automation is bringing major production and safety benefits, but at the same time other factors such as the reduction in workforce numbers and ever-increasing production pressures are leading to high turnover rates. This in turn causes to a loss of experience and expertise. In addition, and of particular importance, is the recognition of psychosocial wellness on workforce safety. Many of these factors are not unique to the mining industry however they may be exacerbated by the scale of mining, the remoteness of the mines and family unfriendly mining rosters.

Apr 16, 2024

By R Symes

The Fosterville Goldmine in Victoria Australia employs the BIOX« Process to liberate gold from its sulfidic flotation concentrate through bacterial oxidation. Gold occurrence is primarily as submicron particles in pyrite and arsenopyrite and has been described as being in æsolid solutionÆ and therefore not amenable to direct cyanidation. Once liberated by the oxidation process, the gold is then available for cyanide leaching. During the oxidation process it has been found that a portion of the liberated gold becomes suspended in the liquid phase in what appears to be a colloidal state. This liquid becomes a waste stream during washing of the oxidised solids and the suspended gold is therefore lost. A method was previously developed using an addition of quebracho tannin to significantly reduce this loss by formation of an iron-tannin precipitate which captures the gold which then reports to the cyanide leach circuit with the oxidised concentrate solids onto which it is adsorbed.This paper discusses the development and plant trial of a second processing step to further enhance gold recovery by use of flotation tailings essentially as a source of extra surface area to capture residual tannin-iron precipitate and its associated gold not recovered in the first step.CITATION:Symes, R, 2012. Recovery of colloidal gold from oxidised concentrate wash liquor - Further improvement, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 383-388 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By M Johnson, M Horrigan

The scope of this report is to examine the aforementioned hypothesis by performing a detailed analytical comparison of a P&H electric rope shovel to an O&K diesel powered hydraulic excavator. In order to complement the integrity of the concluding results, two different size categories will be analysed in order to demonstrate that the findings can be extrapolated and applied to all the machinesÆ size classes. These two size classes are categorised by their bucket sizes and they are in the range of 43 - 58 cubic metres and 23 - 26 cubic metres. It should be noted that electric powered hydraulic excavators will not be considered in this report. In order to compare the electric and hydraulic types, the machine variants that will be analysed are commercial cost-effectiveness and operational flexibility. Although operational flexibility can be an ambiguous characteristic, a clear and thorough definition describing its exact meaning has been included. In order to simplify this study, all the data collected for this comparison have been for overburden removal, eliminating the variation that occurs with the movements of the shovel when selectively mining in the ore deposit. Thus, it ensures that all the data that is compared stems from a common origin for all the shovels. In other words the information will be compared when digging in the same material, loading into the same sized haul trucks, and when possible, with the same operators. Theoretical data received form the respective manufacturers, and actual data obtained from Mount Whaleback, was used for this comparison. This leads to the final comparison, where the operational flexibility and the cost-effectiveness are evaluated, with respect to their individual importance, ultimately influencing the final recommendation.

Jan 1, 2002

By J Northfield, L Neesham

The GRE46 Underground Project lies beneath the environmentally unique and culturally endowed shore of Lake Cowal. The ore body is open both along strike and at depth and is currently defined to a strike length of 1.5km and depth of 800m. The Warraga exploration decline commenced in March 2019 and represents the first stage of the Project, which is expected to underpin production at Cowal Gold Operations (CGO) for a period exceeding 10 years. Mining operations at Cowal commenced in 2005, following a period of over 20 years of exploration and permitting. In 2015 Evolution Mining (Cowal) Pty Limited (Evolution) acquired the operation from Barrick Gold Ltd (“Barrick”). Barrick had a life of mine plan that anticipated a cessation of operations in 2024 at a processing rate not exceeding 7.5 Mtpa. Evolution have grown the regional endowment considerably and have a currently approved mine life out to 2032 with a currently approved maximum processing rate of 9.8 Mtpa. This paper examines the history, current status and future path of one part of that plan, the GRE-46 Underground Project. Topics for discussion include discovery, Mineral Resource growth under different ownership philosophies, planning, permitting and commissioning of an exploration decline and bulk sampling project, and integration with the possible future mine. Environmental sensitivities affecting regulatory approvals, timeframes, technical challenges, opportunities and solutions are discussed, along with the path required to fast-track production from the existing 14Mt, 1.4Moz Mineral Resource while complying with the requirements of modern, responsible project development stewardship.

Mar 15, 2021

By R Burgess-Limerick, J Haight

A review of mining automation experiences was undertaken on behalf of the National Institute for Occupational Safety and Health (NIOSH). The research included a review of literature and guidance materials; analysis of automation related incidents and visits to surface and underground mines in Australia, Brazil, Chile, South Africa, Sweden and the USA.

Apr 16, 2024

The JORC Code contains a mandatory classification system for Mineral Resource and Ore Reserve estimates for public reporting. The classification is a statement of the Competent PersonÆs confidence in the estimate and an attempt to convey that confidence to the various users of the resource estimate. In general the classification process is either largely subjective, relying on the Competent PersonÆs experience, or relies on statistical measures derived from the estimation process, or is derived from an estimated level of confidence in the outcome. However, the statistical measures may not necessarily relate to the overall confidence in the resource or reserve which must take account of the confidence in the geological inputs to the estimation.In addition to the traditional deterministic interpretation and estimations adopted by geologists, semi-quantitative techniques are now available to improve the estimation of confidence while continuing to involve the Competent PersonÆs experience in the process. Methods for quantifying confidence in mineral resource estimates for advanced projects and operating mines have also been developed.Classification is undertaken primarily as a communication tool between the estimators and the other stakeholders in the process. A brief examination of the stakeholdersÆ requirements is included.

Sep 26, 2011

By M Scoble, C Hughes, M Roberts

At 14 per cent, the representation of women working in the mining industry is the lowest among primary industry categories in Canada. Despite an increase in research and industry commitment to advance and retain women in the mining industry, the gender gap in mining organisations persists.This paper is based upon a recent Canadian survey of 163 highly qualified women (HQW) working in the mining sector. For the purpose of this research, HQW were defined as women with a BachelorÆs degree or higher. This research sought to identify career progression and retention patterns of women who in theory have the educational qualifications to advance into positions of leadership in mining operations. We considered why womenÆs advancement in mining organisations has stalled; examined the career development pathways of HQW; and investigated the interactions of mining workplace culture on HQWÆs career development and retention within the Canadian mining industry. Results?indicated two distinct career pathway trends for HQW. æThe specialistÆ; a career characterised by multiple professional scientific and technical positions, and æthe corporateÆ; a career characterised by professional administrative roles and roles in mid-level management. It was found that neither æcorporatesÆ nor æspecialistsÆ systematically progressed into senior management and executive roles. These findings suggest that HQWÆs careers in mining are stalled, despite a strong indication by respondents of interest in their professional career advancement. With regards to?workplace?culture, respondents indicated that blatant forms of gender discrim-ination have been reduced in mining workplaces; however, exclusion from informal networks, implicit bias and subtler forms of workplace discrimination persist. Consistent with previous mining sector research, improving work-life balance, work flexibility and mentorship were found as key drivers for HQW to advance and remain in the industry.CITATION:Hughes, C, Scoble, M and Roberts, M, 2012. Where are the women? Highly qualified women in the mining industry, in Proceedings International Mine Management 2012, pp 23-34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By A Mehrani, F Zamani, A Dehghani

Vibrating screens play an important role in the dry classification circuit of Gol-e-Gohar iron ore processing plant. This circuit was designed to classify the autogenous mill discharge and produce a suitable feed, with K80 about 450 ¦m, for dry magnetic separators. Three parallel vibrating screens produce more than 50 per cent of the separatorÆs feed. The efficiency of the magnetic separator is greatly affected by feed size distribution. In this work, the JKSimMet 5.1 software was used as an analysing tool to assess the flow rates and USIM PAC3 software as the simulation tool to control and optimise the vibrating screens. Samples were collected and the circuit was mass balanced. Then the vibrating screen was simulated and adjustment parameters such as cut-point, bypass and imperfection factor were determined. The product streams of vibrating screens can also be predicted.

Jan 1, 2007

The Indonesian province of Papua is a remote jungle-clad region covering the western half of the mountainous island of New Guinea. Despite being relatively under-explored to this day,Papua is home to the greatest mineral success story of the 20th century. The Grasberg/Ertsberg minerals district atop the central dividing range contains the worldÆs largest reserve of both copper and gold (Freeport-McMoRan Copper and Gold, 2002). With large mines at Ok Tedi,Por gera and Lihir,and many well-delineated resources such as Frieda River,Wafi and Hidden Valley, neighbouring Papua New Guinea,the eastern half of New Guinea has enjoyed sustained exploration campaigns for gold and copper since the mid 1960s. The combined Grasberg and PNG exploration successes can be measured in terms of ounces of gold produced over the last decade versus available landmass,conf irming the island of New Guinea and surrounding islands as a world-class destination for gold explorers. Yet despite this obvious regional prospectivity and the profitability of the Grasberg operation, a sustained exploration effort in the Papua province in Indonesia has not been achieved. Periodic political constraints, poor infrastructure, high costs, operational challenges, social and environmental concerns and lack of immediate exploration success often impact exploration investment decisions. Accordingly a lesser number of mineral occurrences have been documented in Papua compared to those seen along tectonic strike in geologically similar Papua New Guinea.

Jan 1, 2004

By M J. Thurley, L Lindqvist, D Degerfeldt, J Nyström, R Nordenskjöld

Rock breakage is a major component of all mining and mineral processing operations with the particle size distribution linked to productivity through the comminution chain. Optimisation and automatic control of comminution, material handling, and agglomeration processes is a complex task with large potential for gains in productivity, and energy efficiency. A key factor in realising these gains is the requirement for fully-automated online particle size distribution measurement to provide the necessary feedback and input for control. Moreover, to enable automatic control system it is necessary to provide a consistent, reliable size distribution measurement that avoids the significant errors resulting from under-sizing overlapped particles and over-sizing clusters of fine particles. Published literature and observation of commercial systems indicate a body of predominantly 2D photographic based particle size measurement systems that suffer from a number of significant errors except in the simplest case of a monolayer of particles under good illumination with limited colour variation in the material. In order to overcome these limitations a university and industry collaboration developed three-dimensional particle measurement (3DPM) between 2006 and 2012, based on 3D surface profile measurement of the visible material on conveyor. 3DPM avoids particle delineation errors due to variation in material colour and shadows, detects overlapping versus non-overlapping particles, and identifies areas of fine particles as fines and not large rocks. 3DPM measures: the visible material and calculates its particle size distribution, bulk volume, detects boulders, and conveyor belt fill factor in an automated consistent manner. Furthermore, 3DPM’s advanced algorithms allow observation of particle variation that would otherwise be undetected without the capacity to identify visible areas-of-fines and overlapped particles. Boliden Mines has installed 3DPM at three operations for measurement between the stockpile silo and grinding mill, and measurement after the primary crusher. Fragmentation measurements across multiple years of measurement are presented with some observations of plant behaviour. In the future 3DPM results will be incorporated into automatic control strategies for plant optimisation. 3DPM is used across a wide range of material types and applications that also includes; limestone aggregate for quality control in manufacturing, agglomerates for closed-loop automatic control in chemical production, and measurement of coke for size-based blending feed control to the blast furnace in steel production. CITATION:Thurley, M J, Degerfeldt, D, Nyström, J, Nordenskjöld, R and Lindqvist, L, 2018. Automated, online measurement of bulk material size distribution on conveyor using 3D profile imaging at Boliden Mines, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 641–652 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By H-S Yang, H Park, S-J Kim, Y-H Ko, H-S Kim, S-H Cho, J-K Kim

An investigation was undertaken to devise a new method for reducing dust spread during blasting demolition utilising water tube and detonating cord. Modelling of smooth particle hydrodynamics (SPH) with AUTODYN software was initially completed to determine the expected diffusing behaviour of the water tube. The actual behaviour was then captured with high speed videos during each experiment, and each result analysed in detail. Water mist diffusion was generated and analysed by changing three key variables. In sequence, these included changing the location of detonating cord in the tube, the charge quantity and the tube diameter.As a result of experiments and simulation, optimum design for ideal diffusion behaviour was suggested and each behaviour of water mist was classified by diffusing shape of water tube as the design criteria.CITATION:Ko, Y-H, Kim, J-K, Kim, S-J, Park, H, Kim, H-S, Cho, S-H and Yang, H-S, 2015. Mist diffusion experiment and evaluation of water tube for blasting demolition dust control, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 809–814 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By M Erskine, R Mills

This paper approaches tailings dam risk management from the perspective of how other high hazard industries approach the management of their catastrophic event risks, with the aim to provide recommendations from these learnings for the industry to adopt.

Jul 1, 2021