Search Documents

By Charles N. Becker

The practice of drying phosphate in Florida is as old as the industry, which began a little more than half a century ago. The methods, however, have changed considerably. At first, the natural process of exposure to the sun and air was used, later supplemented by wood fires beneath open-air stationary dry kilns and drying towers of various designs. It was not until the early nineties that rotary driers came into use, and at first they were of very small design and fired with wood. As the industry grew and tonnage increased, so likewise grew the number and size of rotary driers, until today the largest installations are 6 ft. up to 7 ft. 6 in. in diameter, and 55 to 60 ft. long, fired with crude oil. The reasons for drying phosphate rock are: (1) to eliminate freight on water in the shipment and (2) to facilitate the good grinding qualities required by the buyers in their acidulation. Phosphate pebbles vary materially in natural characteristics and each property has a direct bearing on the processing. In making comparisons of cost and operating conditions, the following are usually taken into consideration: 1. The hard dense pebbles, which contain very little interior moisture and 6 to 8 per cent total moisture, usually produced from the low-grade deposits. 2. The lighter, porous pebbles, which contain 4 to 5 per cent interior moisture and a total moisture ranging from 9 to 15 per cent. 3. The product of recovery operations using oily reagents, containing from 15 to 25 per cent moisture. 4. The size of the pebbles Usually the plus 5-mesh material is considered as "coarse rock"; the minus 5-mesh plus 24-mesh is "fine rock," and the minute particles below 24 mesh are called "concentrate." 5. The amount of moisture allowed in the dried product. The practice is generally to dry down to 1.5 to 2 per cent moisture. There is, however, an actual range in guarantee of from 1 per cent maximum to 3 per cent maximum.

Jan 1, 1938

By Charles Becker

THE practice of drying phosphate in Florida is as old as the industry, which began a little more than half a century ago. The methods, however, have changed considerably. At first, the natural process of exposure to the sun and air was used, later supplemented by wood fires beneath open-air stationary dry kilns and drying towers of various designs. It was not until the early nineties that rotary driers came into use, and at first they were of very small design and fired with wood. As the industry grew and tonnage increased, so likewise grew the number and size of rotary driers, until today the largest installations are 6 ft. up to 7 ft. 6 in. in diameter, and 55 to 60 ft. long, fired with crude oil. The reasons for drying phosphate rock are: (1) to eliminate freight on water in the shipment and (2) to facilitate the good grinding qualities required by the buyers in their acidulation. Phosphate pebbles vary materially in natural characteristics and each property has a direct bearing on the processing. In making comparisons of cost and operating conditions, the following are usually taken into consideration: 1. The hard dense pebbles, which contain very little interior moisture and 6 to 8 per cent total moisture, usually produced from the low-grade deposits. 2. The lighter, porous pebbles, which contain 4 to 5 per cent interior moisture and a total moisture ranging from 9 to 15 per cent. 3. The product of recovery operations using oily reagents, containing from 15 to 25 per cent moisture. 4. The size of the pebbles. Usually the plus 5-mesh material is considered as "coarse rock"; the minus 5-mesh plus 24-mesh is "fine rock," and the minute particles below 24 mesh are called "concentrate." 5. The amount of moisture allowed in the dried product. The practice is generally to dry down to 1.5 to 2 per cent moisture. There is, however, an actual range in guarantee of from 1 per cent maximum to 3 per cent maximum.

Jan 1, 1936

By J. B. Newsom

IN the September 1936 issue of MINING AND METALLURGY the pioneer work of boring a 5-ft. shaft to a depth of 1125 ft. at the Idaho Maryland mine in California was described. Later, a Bureau of Mines Information Circular (No. 6923) gave additional data. In re¬cent months still further progress has been made in this technique through the sinking of a 5 1/2-ft. shaft for Pickands, Mather & Co. at their Zenith mine, Ely, Minn. The present work was done with new carefully designed equipment and several experienced men so that progress, as shown below has been much better:

Jan 1, 1938

Due to the advanced date of publication of this Bulletin, the lists of new members, changes of address, etc., for the month of July will be printed in the September number of the Bulletin. CANDIDATES FOR MEMBERSHIP. The following persons have been proposed during the period July 1-20, 1913, for election as members of the Institute. Their names are published for the information of members and associates, from whom the Committee on Membership earnestly invites confidential communications, favorable or unfavorable, concerning these candidates. A sufficient period (varying in the discretion of the Committee, according to the residence of the candidate) will be allowed for the reception of such communications, before any action upon these names by the Committee. After the lapse of this period, the Committee will recommend action by the Council, which has the power of final election.

Jan 8, 1913

Optimism over the continued growth of coal ex- ports received a significant shot in the arm September 18 at Norfolk, Va., when huge, new ship coal-loading facilities of the Norfolk & Western Railway were formally dedicated before a large audience of American and foreign dignitaries. Guest of Honor at the occasion was Christian A. Herter, Special Representative for Trade Negotiations, who, in a speech, stated, "The prospects for the expansion of our coal exports are excellent. The competitive pricing and high quality of our coals, whether for the production of coke for steel mills or for the generation of electric power, have won the respect of consumers everywhere in the world. Last year, the United States coal industry exported over 40 million net tons. . . . There are excellent reasons to believe that by 1970 we shall be exporting at double this rate."

Jan 10, 1963

By D. G. Russell

A simple method has been developed with which flowing bottom-hole pressure data from two-rate flow tests in oil or gas wells can be analyzed to estimate the formation permeability, skin factor and average reservoir pressure. The required pressure data are obtained by observation of the transient bottom-hole pressure behavior after the stabilized producing rate of the well is changed to another, higher or lower, rate. The new method yields the same information as a conventional pressure buildup analysis, but eliminates the need for closing in the well. The analysis of a two-rate flow test is of the same degree of difficulty and requires about the same engineering time for application as a conventional pressure buildup analysrs. The extended closed-in periods experienced with conventional buildups because of long, low-rate afterproduc-tion periods are eliminated by fIow tests. Other anomalous pressure buildup effects, such as "humping" due to weli-bore phase segregation, can be successfully eliminated with the new method. Generally, flow tests of about 24 hours' duration run with conventional pressure measurement equipment are sufficient for interpretation purposes. Field testing of the two-rate flow test method has established that it is a reliable and economical method which can be used in many instances to complement or even replace conventional pressure buildup methods. INTRODUCTION The principal method for estimating formation permeability and well damage, or skin factor, in a producing oil or gas well is the analysis of shut-in bottom-hole pressure buildup data.' This familiar method has been used quite successfully by reservoir engineers for many years. It is based on the solution of the radial flow equation for constant rate conditions, and requires that the well be closed in for a sufficient period of time to obtain a clearly defined linear portion on the plot of observed t + ?t bottomhole pressure vs log t + ?/?t(where At is shut-in A? time, and t is producing time to the instant of shut-in). From the slope of the plot and other normally obtainable data, the permeability, skin factor, and reservoir pressure at infinite shut-in time (if the reservoir were infinite) can be estimated. Over the years several drawbacks have become apparent in the use of conventional shut-in pressure buildups for determining permeability and skin factor. The conventional pressure buildup interpretation theory assumes that a well is closed in at the sand face and that no production into the well occurs after shut-in. In practice, of course, the well is closed in at the surface, and inflow into the well continues until the well fills sufficiently to transmit the effect of closing in to the formation. This adjustment period is commonly referred to as the "after-production" portion of the pressure buildup. In the tight reservoirs, long, low-rate after-production periods frequently occur, and the well must be shut in for several days or, in some instances, even weeks to obtain an interpretable buildup curve.' Obviously, such long shut-in times can cause loss in current income, both from reduced oil production and from the fact that personnel and pressure measurement equipment are occupied with a single well for too long a time. In other cases, even long shut-in periods do not seem to be of much aid in obtaining an interpretable buildup." If there is considerable phase redistribution (liquid fallout or bubble rise) after a well is shut in, then curves with no interpretable portion are often obtained during the buildup. In addition to instances in which wellbore effects cause trouble, there are also cases in which the major objection to use of the closed-in pressure buildup is simply the fact that the well must be shut in. When there is no proration and when the well has limited producing capacity. closing in the well means loss of income. From the foregoing discussion it is apparent that it ib desirable to have an alternative method of obtaining the same information as that derived from a conventional buildup without the need of closing in the well. One possible solution which has been offered for this problem is the use of a bottom-hole shut-in tool' which isolates the major portion of the flow string from the formation face during the buildup. In this paper an alternative method which is frequently successful in avoiding wellbore effects and which does not require the use of special equipment is presented. A new, simple method has been developed with which the flowing bottom-hole pressure data from flow tests in oil or gas wells can be used to estimate permeability, skin factor and the average reservoir pressure. The required pressure data are obtained by observation of the transient bottom-hole pressure behavior after the stabilized production rate of the well is changed to another, higher or lower rate. The need for closing in the well is eliminated, and pressure measurement periods of only 18 to 24 hours arc usually sufficient, even in tight reservoirs. Thus, the new

By Hans Strack

Electroluminescence of GaAs p-n junctions fabricated by simultaneous diffusion of sulfur and iron was investigated at 77°K. A narrow emission peak with a half width of about 4 kT in the energy range between 1.14 and 1.155 eu was attributed to iron. Other transition elements exhibited light emission in the vicinity of the iron peak, namely nickel between 1.15 and 1.16 ev and cobalt between 1.16 and 1.17 ev. The efficiency of the doping with iron depended on the amoz~nt of arsenic present. A weight ratio of arsenic to iron of 4:l was sufficient to observe the emission lines associated with transition elements. The presence of oxygen reduces the intensity of the light emission. In addition to the levels associated with transition elements, levels at 1.05 and 1.28 ev, probably due to lattice defects, are observed except in diodes fabricated in solution-grown GaAs. THE near band edge emission of GaAsp-n junctions has been studied extensively in the past.' GaAs devices utilizing spontaneous and stimulated near band edge emission are of considerable practical importance. Typical junctions are fabricated by diffusion of a heavily doped p region into degenerate n-type GaAs. Much less work has been done on investigating the radiative recombination via deep levels in lightly doped p-type material. This area is of interest in understanding the performance of GaAs n-p-n transistors. GaAs transistors show remarkable improvement in high-frequency performance and current-gain stability at high temperatures, when iron is added to sulfur during the emitter diffusion process. The present work was initiated to investigate deep-level electroluminescence of iron-doped GaAs p-n junctions fabricated on vapor-phase epitaxial GaAs and on solution-grown GaAs. For comparison several diodes doped with cobalt and nickel were studied. Iron, cobalt, and nickel have an electron configuration of the type

Jan 1, 1968

By Ralph Monaghan, Arthur Youmans

General principles of scintillation counter-type instruments for radioactivity logging are discussed and the various possible causes for instability are examined. It is shown how instrumentation problems are solved. Means are discussed for minimizing drift and instability due to "fatigue" of the photomultiplier tube and neutron activation of the crystals. INTRODUCTION Neutron and gamma-ray logs made with logging instruments employing scintillation counters are now routinely available from most of the logging service companies. The superior characteristics of scintillation counters by comparison with older types of detectors promises to bring about important improvements in quantitative interpretation of radioactivity logs. Moreover, new types of logs can be made with scintillation counters which are not possible with other detectors. But in spite of the obvious superiority of these counters with respect to efficiency, speed, and versatility, they suffer from a number of inherent difficulties and weak- nesses. Unless these inherent diffi-culties are fully recognized and satisfactorily overcome by sound engineering of the associated instrumentation, scintillation counter logs are particularly likely to exhibit drift and instability of sensitivity. This defect in logs when they are intended for quantitative interpretation is intolerable and more than outweighs any advantages over the older type of instrumentation when the latter is operating correctly. SCINTILLATION COUNTER OPERATION In general all radioactivity logging instruments consist of a detector sensitive to gamma radiation or to neutron radiation coming from the strata. This radioactivity is either due to naturally decaying radioactive elements in the rock, radioactivity induced in the rock by a neutron source in the instrument, or scattering by the rock of neutrons or gamma rays coming from a source in the instrument. In the scintillation counter the gamma radiation or neutron radiation reacts with the scintillation phosphor to produce light pulses. These light pulses are then converted to amplified electrical pulses by the multiplier phototube. Basically the problem of making a good scintillation counter logging instrument is to make the radiation sensitivity of the system as nearly constant as possible. The size of each scintillation counter pulse is dependent on the energy of the individual quantum of radiation being detected. In normal radiation logging, gamma rays of all energies, up to some maximum value, reach the detector. If a suitable scintillator is used, such as a sodium iodide crystal, each gamma ray produces a number of photons proportional to the energy absorbed by the crystal from the impinging radiation. The light flashes are detected by means of a photo-multiplier tube which contains not only a photo-sensitive cathode from which photoelectrons are collected, but also an amplifier, called an electron multiplier, built inside the photomultiplier tube; the electron multiplier usually has about 10 stages, having an over-all gain of perhaps 500,000. In an ordinary gamma-ray log one wishes to detect all gamma rays down to the lowest possible energy; therefore, one wishes only to reject the "noise" pulses which are invariably present due to thermal emission of electrons from the photo-cathode of the photomultiplier. In other radioactivity logs it may be desired to measure the radiation within a particular energy band, or above

Jan 1, 1958

By Gerald, Sherman

INCREASED production and con¬sumption of all metals, indicate the progress of industry toward that condition formerly thought to be normal. With no market limitations on silver and gold the two new precious-metal mines, the Silver Queen (now the Golden Queen), in southern California, and the Sunshine, at Kellogg in northern Idaho have made progress toward a high routine production. The Golden Queen 300-ton mill is finished and ready. The Sunshine mill has been enlarged and production is now at the rate of 500 tons per day of high-grade silver ore. The Hecla Mining Co. is developing the Polaris vein, which should be the extension of the Sunshine to the east. Some rich ore is reported. The developments of the' East African Gold Fields, Ltd., in the Lupa gold field of Tanganyika Territory, have made good progress, but operation in an isolated locality is not rapid and a large plant will be required. There have been no other discoveries reported that can be compared with the three mentioned, but production has increased, with greater capacity in dredging equipment and underground mines more adequately prepared for production.

Jan 1, 1936

By John L. Walter

A sintered compact of iron containing 0.007 vol fraction of glass , prepared 6). powder rnetullurgtcal lechniques, was rolled lo foil, 0.001 in. /hick. The foil sullrples were anneuled a1 650° to 850°C in hydrogen. Pri,narj recryslullization prodtnced large grains which Lc3ere highly elongnled in the rolling direclion und which had an unusual prgferred orientation. The glass parlicles assumed a stringerlike dispersiorz on working; llie slrinyers were parallel lo the rolling direction and to the long axis of the grains. The same unusual grain structure, preferred orientation, and stringerlike dispersion of purticles are found in heal-ily rolled and annealed foil of tungsten which has heen doped wilh small amounts of aluminum, silicon, and polassiutvt. Both the proper dispersion of the particles and severe working (reductions in excess of 98 pct) are necessary to produce the elongzcted grain structure. RECENTLY, the author reported on the origin of the elongated or "nonsag" grain structure in tungsten foil which was doped with aluminum, silicon, and potassium.' It was observed that particles, identified as mullite (Al6Si2Ol3), were present in the doped ingot (as sintered) and at all stages of processing from ingot to sheet or wire. It was shown that the particles, being plastic at tungsten working temperatures (up to 1550"C), underwent a "stringing out" parallel to the working di-direction. It was concluded that these strings of particles were responsible for the formation of the highly elongated interlocking grains observed in doped tungsten wire or sheet. To give further credence to this explanation of a long-observed but not understood phenomenon, it was decided to design a new system, one which was analogous to the doped-tungsten system. Thus, a bcc metal, iron, was chosen to be doped with glass which would be plastic at reasonable working temperatures for iron. The glass chosen was a #0080 Corning lime glass which melts at about 810°C. This is approximately the same fraction of the melting point of iron (0.6) as the melting temperature of mullite is of tungsten. It will be shown that all the observed unusual features of the doped tungsten are duplicated in the glass. doped iron, even to the preferred orientation of the grains in the recrystallized sheet. In the tungsten sheet the preferred orientation consists of two components, (1i3)(691) and (013)(362), neither of which has been observed as a component in textures of primary recrystallized bcc metals. EXPERIMENTAL PROCEDURE The glass, in the form of fine powder, was added to high-purity electrolytic iron powder and mixed dry. The particular composition chosen was 0.007 vol fraction of glass. After mixing, the powder was mechanically pressed to a disk 0.5 in. diam and 0.15 in. thick at a pressure of 5000 psi. The pellet was sintered, in pure dry hydrogen, for 2 hr at 8 50°C. The sintered pellet was then heated to 750°C and rolled to 50 pct reduction of thickness in two passes, with reheating between passes. The rolling temperature was then reduced to 600°C and the slab was rolled to a thickness of 0.050 in. Rolling to 0.010 in. was accomplished in several passes at 300°C. Final reductions to 0.003 and 0.001 in. were taken at room temperature. This rolling temperature schedule was similar, in terms of the fraction of the melting point, to that used in the rolling of the doped tungsten. The total reduction of thickness was in excess of 99 pct. Samples of the rolled foil were lightly electro-polished and annealed for 1 to 6 hr at temperatures of 650" to 85O°C in hydrogen. Samples for transmission electron microscopy were thinned on a Disa Electropol using AC-1 electrolyte.

Jan 1, 1968

By R. A. Greenkorn, R. C. Smith

Hele-Shaw cells are used to model creeping flow through porous media (where Darcy&apos;s law is valid). The effects of inertia on flow about obstructions in a Hele-Shaw cell can be calculated by a perturbation method if one can determine a solution to Laplace&apos;s equation. Results of a computer solution for flow about circular, square and elliptical obstructions are presented. These results show that or a modified Reynolds number of less than I, the inertia terms are small; and for values of less than 3, the average streamline predicts the ideal flow. Therefore, the analogy might be used for studying flow in porous media up to a modified Reynolds number of at least 3. INTRODUCTION The nature of fluid flow in porous media is of interest in the fields of soil mechanics, ground water flow, petroleum production, filtration and flow in packed beds. Because it is very difficult to study the phenomenological behavior of flow in porous media, homologs and analogs are used to study flow characteristics. A Hele-Shaw model, made of two closely spaced plates - usually glass — is often used as an analogy to two-dimensional flow in porous media. Hele-Shaw2 showed experimentally that the streamline configuration for creeping flow around an obstacle located between two closely spaced parallel plates is the same as for two-dimensional, ideal flow about the same obstacle. Stokes7 verified these observations mathematically. The usual equation of motion for flow in porous media is Darcy&apos;s law. The form of the mathematical statement of Darcy&apos;s law is identical, within a multiplicative constant, to the expression for the average velocity over the plate gap in the plane of a Hele-Shaw model. These models may be used to describe flow in both homogeneous and heterogeneous porous media. In the mathematical proof of the Hele-Shaw analogy it is assumed that the convective terms in the Navier-Stokes equations are negligible and that the equations of motion degenerate to Laplace&apos;s equation, with pressure the dependent variable. Whenever a Hele-Shaw model is used as an analogy to flow in porous media, .the validity of this assumption is in question. Riegels5 showed that if convection is not neglected, the velocity distribution around a cylindrical obstruction in the flow field depends on a Reynolds number, the plate spacing, and a dimension characteristic of the obstacle. Riegels&apos; solution, a perturbation solution, uses the boundary condition that the flow rate into the obstacle averaged over the plate gap at any point on the obstacle is zero. The method requires that a solution to Poisson&apos;s equation for the perturbation pressure be found. Riegels evaluated this solution for the case of the cylindrical obstruction. His method may be simplified by eliminating the need for solving Poisson&apos;s equation for the perturbation pressure. Instead, an analytic expression for the perturbation pressure gradient is obtained (valid for arbitrary shapes) and used to eliminate pressure from the equations for the perturbation velocities. The results show, for symmetrical shapes, that if NRe < 1, the convective acceleration terms are small, and that the average velocities represent ideal flow up to at least NRe = 3, where: L is a characteristic dimension of the obstacle perpendicular to flow, b is the plate spacing, u is viscosity, v, is velocity of approach and p is density. THEORY* Incompressible fluid flow through a Hele-Shaw model and a porous medium are analogous because the equations for the average velocity components in two-dimensional flow are identical if:

Jan 1, 1970

By B. N. Thompson

Main industrial minerals produced in New Zealand are nonmetallic - clay, dolomite, limestone, pumice, salt, serpentine, and silica sand. Other minerals, some with minor production, include diatomite, feldspar, magnesite, sulfur, asbestos, and perlite. Energy and metallic minerals and aggregate are excluded from this account. These industrial minerals occur in a wide range of rock types and geological ages. For example, clays are known from the weathering products of Cretaceous rhyolite and leaching of Eocene coal measures; from Quaternary weathering of contemporary loess and shallow marine sediments, and of greywacke of Triassic-Jurassic age; and from the hydrothermal alteration of late Cenozoic acidic volcanic rocks.

Jan 1, 1984

By P. G. Winchell, R. J. Russell

The distribution of displacements of originally plane surfaces by an invariant-plane strain has been analyzed statistically. The displacement ratio (the magnitude of the displacement of a point originally a unit distance from the invariant plane) can be determined from an analysis either of tilts of random surfaces or of displacements of random scratches scribed on a randowz surface. In either case the mean of the tangent of the observed displacement angle is related to the displacement ratio, and the number of observations used in determining the mean is related to the confidence limits placed on the estimate of the displacement ratio. In estimating the effect of applied stress on a phase transformation whose displacement effects can be approximated as an invariant-plane strain,* the dis- placement ratio of the invariant-plane strain is of primary importance. Two procedures for determining such displacement ratios are considered here. In the tilt method the measured quantity is taken to be the angle through which a random polish plane is rotated by the invariant-plane strain. In the scratch method the measured quantity is taken to be the angle between the original direction of a random scratch in a random polish plane and the projection of its final direction in the polish plane. In order to obtain precise results from either of the methods, it is necessary to measure the relative volume change associated with the strain in a separate experiment. TILT METHOD A locally homogeneous invariant-plane strain, P, with displacement ratio, S, may be written&apos; where ; and < are unit vectors indicating the displacement direction and invariant-plane normal, respectively, as pictured in Fig. 1. Eq. [I] describes a uniaxial strain if the direction of displacement is parallel to the invariant-plane normal and a pure shear strain if the displacement direction is perpendicular to the invariant-plane normal. The original orientation of the random polish plane relative to the invariant plane and to the displacement direction is shown in Fig. 2. The angle 03 between < and u is related to the relative volume change, ?V/V, and to the displacement ratio by As a result of the invariant-plane strain, the polish plane is rotated about its intersection with the invariant plane by the angle y, which is always taken to be positive. The tangent of this angle in terms of the above parameters is

Jan 1, 1967

By C. D. Michaelson

The memory of D. C. Jackling serves chiefly to remind us how much we owe to the pioneers of our industry. Jackling was one of the giants. Orphaned at the age of two, he made his way through sheer persistence and plain hard work. His brilliance gave rise to a vision, and his tenacity made his vision a reality. Foreseeing that economies of scale would make the handling of low-grade ore profitable, he introduced the revolutionary concept of open-pit copper mining. During World War I, the defense effort of the United States was immeasurably strengthened by the tremendous supplies of copper from the western mines that Jackling had made possible. Again in World War II, the demands for copper were supplied, and the nation once more had profound reason to be grateful to this rugged, stubborn man who had long ago ventured into the mountains and unlocked their wealth. We are now embarked upon another great era of change, and we must devise new concepts to meet it. The task is not only to create new techniques of mining, but to forge better ties between men and institutions which will let us work in harmony with the techniques we have. We might recall that while Jackling was a man of towering pride and formidable will, he was also adept at getting others to share his vision and join his purpose. Today our reach for cooperative endeavor must go far beyond our own shores as we seek to develop the buried riches of distant lands. And we would do well to remember that Jackling&apos;s remarkable insight would have come to nothing had not British investors been willing to provide much of the initial capital. As was true of so many early enterprises in America, European capital was absolutely essential.

Jan 4, 1969

By A. M. Gaudin, D. W. Fuerstenau

By streaming potential techniques, the zeta potential of quartz has been measured as a function of the concentration of dodecylammonium salts at different pH values. These experiments indicate that adsorption of dodecylammonium ions takes place as individual aminium ions until a certain critical concentration is reached in the double layer, at which point the adsorbed collector ions begin to associate into patches of ions, called hemi-micelles. Because of its effect on the surface potential of quartz, pH controls the adsorption of dodecylammonium ions. The value of cooperating agents and nonionized constituents of flotation systems is discussed. A PREVIOUS investigation&apos; of the role of pH in the flotation of quartz with anionic collectors is here extended to an inquiry of how the cationic collector, dodecylammonium acetate, is adsorbed at the quartz-solution interface. The equilibrium amount of this collector adsorbed by quartz has already been measured as a function of concentration and pH.2,3 The weight of prior evidence has suggested that two mechanisms are involved in the adsorption of this collector by quartz, but with existing adsorption measurements alone it is not possible to determine what the mechanisms are. Gaudin and Bloecher2 postulated that a polymolec-ular adsorption coating begins to form before the first monolayer has been completed. Gaudin and Morrow4 indicated that a similar situation might exist in the film of dodecylammonium ions on hematite. A study of electrokinetic potentials at the quartz-solution interface provides some detail toward a fuller understanding of the adsorption mechanism. Experimental Results The zeta potential at the quartz-solution interface was calculated from streaming potential data measured with the apparatus described in detail in a thesis by Fuerstenau5 and briefly in a paper by Gaudin and Fuerstenau.1 The quartz used in these experiments was a 48/65-mesh fraction prepared in the manner described previously.&apos; Zeta potential of quartz was obtained for various amounts of the amine salt at pH 4, 7, 10, 11. In

Jan 1, 1956

By R. O. Harma

Introduction Wet autogenous grinding is utilized in three iron ore concentrating plants operated by the Cleveland-Cliffs Iron Company (CCI). This paper will trace some of the development in converting from the use of metal grinding mill liners to the use of rubber and will update the current performance of rubber liners in these applications. The Cleveland-Cliffs Iron Company is a natural resources firm with major interests in iron ore mining and processing and oil and gas contract drilling. The company also has interests in oil shale, uranium, forest products, and Great Lakes shipping. The three operations discussed in this paper are the Empire and Tilden Mines on the Marquette Iron Range in Michigan&apos;s Upper Peninsula and the Sherman Mine in northern Ontario, Canada. The Empire Iron Mining Partnership is managed by The Cleveland-Cliffs Iron Company and is owned by Inland Steel, McLouth Steel, The Cleveland-Cliffs Iron Company, and International Harvester. The Tilden Iron Mining Partnership is also managed by The Cleveland-Cliffs Iron Company and is owned by Algoma Steel Corporation, Ltd., Jones & Laughlin Steel Corporation, The Cleveland-Cliffs Iron Company, Steel Company of Canada, Wheeling-Pittsburgh, and Sharon Steel Corporation. The Sherman Mine is a joint venture managed by Cliffs of Canada, Ltd. and owned by Dominion Foundries and Steel Company, Ltd. and Tetapaga Mining Company, a wholly owned subsidiary of The Cleveland-Cliffs Iron Company. The concentrators at all three mines utilize two stage autogenous grinding. Empire and Sherman process magnetic iron ores (Table 1) and utilize magnetic, hydraulic, and flotation concentration methods. Tilden processes an oxidized iron ore (martite, goethite, and hematite) and utilizes a selective-flocculation desliming and flotation concentration flowsheet. Final grind particle sizes are 90% -325M (43k) at Sherman, 90% -500M (25,u ) at Empire and 85% -500M (25 µ) at Tilden. Developmental History The success of using rubber mill linings in Scandinavia led to the first rubber mill lining used by CCI. It was installed in a conventional primary ball mill at Republic Mine in 1964 as reported by Lindroos (1970). This was followed by additional rubber liners for both primary and regrind ball mills. Generally these rubber linings provided about twice the service life as compared to the Type I Ni-hard liners previously used. Grinding efficiency of rubber was found to

Jan 1, 1982

By P. Chiotti, J. T. Mason

Ther?nal, X-ray, metallographic, and vapor pressure data were obtained to establish the phase diagram and standard free energy, enthalpy, and entropy of formation for the compounds in the Sw-Zn system. Four compounds, SmZn, SmZn2 , SmZn4.s, and SmZn8.5, melt congruently at 960°, 94Z°, 908°, and 940°C, respectively. The cornpounds SlnZns, Sm3Znll, and SnzZn7.3 undergo peritectic decomposition at 855", 870°, and 890C, respectively. Another compound of uncertain stoichiometry, SmZn11, undergoes peritectic decomposition at 760°C. Four entectics were observed with the following compositions in weight percent zinc and eutectic tenzperatures in degrees Centigrade: 12 pct, 680°C; 36 pct, 890°C; 58 pct, 850°C; and 72 pct, 900°C. An allotropic transformation and a composition range were observed for the SmZnz compound. The transfor)nation varies from 905" to 865°C as the zinc content increases from 16.0 to 48.5 wt pct, respectively. The free energy of formation of the compounds at 50PC varies between -15.9 kcal per mole for SmZn to -51.1 kcal per mole for SmZn,.,. Corresponding enthalpies vary between -19.2 to -78.3 kcal per mole. The ther-modynamic properties for the liquid alloys are described by the relations: A search of the literature revealed very little information on the Sm-Zn system. Chao et al.&apos; as well as Iandelli and palenzonai have reported the structure of SmZn to be cubic B2 type and Kuz&apos;ma et al3. have reported the structure of -sm2zn17 to be of the Th2Ni17 type. The purpose of this work was to establish the phase diagram of this system, to determine the zinc vapor pressure over the solid two-phase regions of the SYstem, and to calculate the thermodynamic properties of the compounds. MATERIALS AND EXPERIMENTAL PROCEDURES The metals used in this investigation were Bunker Hill slab zinc 99.99 wt pct pure and Ames Laboratory samarium. Analysis of the samarium by chemical, spectrographic, and vacuum-fusion methods gave the following average impurities in ppm: Nd, <200; Eu, <100; Gd, <100; Y, <50;Ca, 225; Ta, 400; Mg, 10; Cu, ~50; 0, 175; H, 20; and N, 15. The elements Fe, Si, Cr, Ni, Al, and W were not detected. The samarium was received as sponge metal and was kept under argon except when being cut with shears and when being weighed. Tantalum was found to be a suitable container for alloys with zinc contents up to the Sm2Znl, stoichio-metry. At higher zinc contents the grain boundaries of the tantalum containers were penetrated by the alloy and the containers failed during prolonged annealing. About 25 g of massive zinc and samarium sponge were sealed in tantalum crucibles equipped with thermocouple wells. These crucibles were in turn sealed in stainless-steel jackets. All closures were made by arc welding under an argon atmosphere. The samples were equilibrated in an oscillating furnace and in some cases were given various heat treatments in a soaking furnace. After appropriate heat treatment the steel jackets were removed and the alloy subjected to differential thermal analysis. The apparatus was calibrated against pure zinc and pure copper and found to reproduce the accepted melting points within 1°C. Alloys were subsequently subjected to metallographic examination and those of appropriate compositions were used for X-ray diffraction analysis and for zinc vapor pressure determinations. The vapor pressures were determined by the dewpoint method. Both the differential analysis and dewpoint measuring apparatuses have been described in earlier papers.4, 5 All alloy samples were etched with Nital (0.5 to 3 pct nitric acid in alcohol) except the samarium-rich alloys. These more reactive alloys were electro-polished in a 1 to 6 pct HClO4 in methanol solution at -700c at a potential of 50 v. EXPERIMENTAL RESULTS Phase Diagram. The results of thermal analysis are indicated by the points on the phase diagram, Fig. 1. Eight compounds and four eutectics were observed. The composition of the compounds and their melting or peritectic temperatures are given on the phase diagram. The four eutectic compositions in wt pct zinc and eutectic temperatures in % are: 12 pct,- 680°C; 36 pct, 890°C; 58 pct, 850°C; and 72 pct, 900°C. The stoichiometry of the most zinc-rich compound is still uncertain, but is very likely either SmZnll or SmZnlz. However, to simplify the presentation which follows it will be referred to as SmZnll. As shown on the phase diagram the phase regions for some of the samarium-rich alloys have not been unambiguously established. A sample of pure samarium was observed to transform at 924°C and to melt at 1074"C, in good agreement with corresponding val-

Jan 1, 1968

By GEORGE W. HARHIS

IN the earlier period of anthracite-ruining, much coal was wasted, both underground and in the culm-banks on the surface. Such waste is common in the development of new mining districts, in which, as a rule, only the richest material can be profitably treated. In the anthracite-region, special causes operated to increase this evil. The mines were generally operated under 20-year leases, and royalties were paid upon such coal only as was actually marketed. The lessees consequently cared for immediate profit only. They were- not bound to win all the coal they exposed, or to leave it in such condition that their successors could win it. Nor was it their interest or duty to educate consumers in the use of their product. The market called for coal of large sizes ; and such coal they furnished, throwing away the rest. Any pains taken by them to bring about a more rational use of coal by their consumers would have borne fruit, after their leases had expired, to the benefit of somebody else. A full statement of the situation wits given in 1893, in the report of the State Commission, appointed in 1889 to investigate the subject.` That body included the names of Heber S. Thompson, William Griffith and the late Eckley B. Coxe.2 Its report gives special attention to the utilization of the old culm-banks.

Nov 1, 1905

By Shiro Ban-ya, John Chipman

The effects of many alloying eletnents on the acticity coefficient of sulfur in liquid iron have-been studied by the equilibriutn in the reaction Sfin Fe) + Hz = HzS at 1550°C&apos;. Results are expressed in terms of a concentration variable for a nonmetallic or for a substitutional metallic solute. Activity coefficient of sulfur, defined as increased by B, Al, C, Si, Ge, Sn, P, As, Sb, Mo, W, Co, and PI. It is decreased by Cu,Au, Ti. Zr, V, h&apos;b, Ta, Cr, ,23n, and Ni. Irulues oj. the interaction coejficient 0i = 6 In are labulated. The same interactions are expressed also in terms of atom fraction and of weight percent. The thermodynamic properties of sulfur in liquid iron have been fairly well established. Our recent paper1 reported new determinations of activity coefficient up an atom fraction of 0.12 and equations based on a careful review of all published data. The effects of alloying elements on the activity of sulfur have been studied by several investigators,2"11 especially by Morris and Williams for silicon,&apos; by Morris and Buehl for carbon,~ and by Sherman and Chipman for manganese. phosphorus, and al~minum.~ However, the effects of some important alloying elements remain to be determined. The purpose of this investigation was to determine the effects of many alloying elements on the activity of sulfur in Fe-S-j ternary systems. EXPERIMENTAL METHOD This study was based on experimental determination of equilibrium in the reaction at 1550°C: The same apparatus and procedure as described in our previous paper have been retained, and the same corrections were applied for dissociation of H2S. The alumina crucibles used in the experiments consisted of four separate compartments. In a given experimental run. kach of three alumina crucibles held four different samples of about 3 g each which reached equilibrium in the same gas atmosphere and temperature. The charges were made up of electrolytic iron, pure iron sulfide, and desired alloying elements, which were pure metal or master alloys made in the laboratory. The weighed samples were held for 4 to 12 hr in the prepared atmosphere at 1550°C. They were then low- ered to be cooled as quickly as possible. The quenched metal beads were crushed to avoid the errors of segregation in the ingot. The sulfur content was determined gravimetrically and alloy content by appropriate chemical analysis. CALCULATIONS The apparent equilibrium constants of Eq. [I] are expressed as follows from the corrected gas ratios and sulfur concentrations: The term K" is the observed equilibrium constant in any given ternary solution, K&apos; is the value for the Fe-S binary solution. and the limiting value of K&apos; in the infinitely dilute solution is designated by K, which is the true equilibrium constant in Eq. [I]. In the thermodynamic treatment of nonmetallic elements in a metallic solution, it has been suggested1&apos; that the lattice ratio has certain advantages over other variables to express the concentration of solute. In interstitial solid solutions the lattice ratio zj is proportional to the ratio of filled interstitial sites to those which remain unfilled. The equations derived for the activity of the solute using zj as the concentration variable are found also to be applicable to liquid solutions containing nonmetallic solutes when the nonmetal is treated as if it were interstitial. For this purpose we adopt the following definitions: The quantity vj which is negative for interstitial solutes is taken as -1 for nonmetallic and +1 for metallic solutes. For purposes of calculation however ; j may be assigned a value which results in a linear relation such as shown in Figs. 1 to 15. The activity coefficient of sulfur, Qs, and equilibrium constant. K(z). are defined as follows: According to a Taylor series expansion. the logarithm of the activity coefficient of sulfur in Fe-S-j ternary system is: However, the value of 6 In */6zi remains constant through a broad range of dilute solutions and the terms of higher order are negligibly small. As a consequence, Eq. [6] is simplified as follows:

Jan 1, 1970

By Raymond Sanford

IT IS difficult to know just when a hoisting rope should be removed from service and a new one substituted. It is desirable to utilize the full life of a rope but, on .the other hand, the damage and possible loss of life, resulting from delay in replacing it may amount to many times the cost of a new rope. In the present methods of inspection the inspector must rely upon accumulated experience and a certain sixth sense or intuition in addition to any rules that may be laid down regarding the number and distribu-tion of broken wires. This condition does not neces-sarily arise from lack of interest among users or makers of rope, but is due rather to the lack of satisfactory or adequate methods for testing ropes to determine their exact condition. The main difficulty in devising a physical test lies in the fact that a number of causes, all operating in different ways, contribute to the deterioration of a rope in service, and affect not only the external conditions but also the inner structure of the material of which the rope is constructed. Wear and broken wires on the outer part of the rope are not difficult to detect, but a test is needed which will clearly indicate the presence of broken wires in the interior portions and the change in strength due to alterations in the structure and properties of the material itself.

Jan 7, 1923