Search Documents

By Otto C. Kopp, Thomas B. Crattie, Dennis R. Owen

Whole-rock analyses of limestones, fine-gralned dolostones and coarser-grained dolostones adjacent to mineralized breccias (Coy mine, Mascot-Jefferson City district) were compared with similar lithologies adjacent to apparently non-mineralized breccias at the new Thorn Hill section located approximately 39 km north of the Coy mine. Specimens were analyzed for Ca, Mg, Si, Al, K, Fe, Mn, Sr, Br, C1, S, Ti and P using X-ray fluorescence analysis. The concentrations of the major and most minor elements for Thorn Hill specimens fall within the range of concentrations for Coy mine specimens; however, significant differences (probability < 0.05) were noted for Fe, C1 and Br for fine-grained dolostones and for MgO, Fe and Mn for the coarser-grained dolostones. No significant differences were detected for the limestones.

Jan 1, 1985

By Theron Wasson

No major oil-field discoveries were made County; the second in Marion township, in Michigan during the year 1940. Produc- Osceola County. Both are producing from tion for the year was maintained by the Stray sand at about 1350 ft. These discoveries made in 1938 and, as a result, is fields are on structures founci by core test-below the total for 1939. Several extensions ing through the glacial drift. The Six Lakes to old fields have been made, which have field, Montcalm County, discovered in helped to maintain production in the face 1934, is Michigan&apos;s largest gas-producing of rather rapid decline in the fields of the field. it has 195 wells producing from the southwestern part of the state. Important Michigan Stray sandstone and the Upper extensions were made in Overisel, Porter, Marshall sandstone. This field was devel-Sherman, and Adams fields. Important oil oped on a 40-acre spacing plan, and gas fields of the state are shown on the -map, Fig. I. WiI~dcat Drilling Michigan&apos;s production of 19,700,000 bbl. A test in sec. 29, Winterfield township, during 1940 was 3,800,000 bbl. less than Clare County, which is producing oil from the total for 1939, but about one million the Monroe of Devonian age at a depth of greater than 1938. This brings the total 3760 ft., and a well in sec. 31, Lincoln accumulated production for the state to a township, Osceola County, producing from little over 145,000,000 bbl. the Monroe at 3625 it., should be classed as wildcats that are sure to lead to further Active Oil Fields development in I94L The leading producer for the year was the At the end of the year the Gulf Refining Temple field, Clare County, where 29 new Company&apos;s deep test on the Kawkawlin wells were drilled. The Walker field, Kent structure in Monitor township, Bay County, was second, but drilled 183 new County, was preparing to drill deeper after wells in order to gain that position. In the having had a gas blowout from a depth of extension of the Overisel field in Allegan 7775 ft. This test is the most important one County, 115 new producers were drilled. drilling at the end of the year in Michigan, The Adams field, Arenac County, was for should it develop commercial produc- revived by several wells with initial production from deeper beds it will lead to deeper tions of over 1000 bbl. per day from the drilling on many well-known structures Dundee of Devonian age. that have been producing from shallower sands. Active Gas Fields Two important gas fields were discovered Exploration by Taggart Brothers during the year. The A small amount of reflection seismograph first was in Riverside township, Missaukee work was done in Clare, Osceola, and Glad-Win Counties during the year. Exploration Manuscript received at the office of the Institute March 28 1941 by shallow drilling for structural informa- tion on beds below the glacial drift con- 347

Jan 1, 1941

By Theron Wasson

No major oil-field discoveries were made County; the second in Marion township, in Michigan during the year 1940. Produc- Osceola County. Both are producing from tion for the year was maintained by the Stray sand at about 1350 ft. These discoveries made in 1938 and, as a result, is fields are on structures founci by core test-below the total for 1939. Several extensions ing through the glacial drift. The Six Lakes to old fields have been made, which have field, Montcalm County, discovered in helped to maintain production in the face 1934, is Michigan&apos;s largest gas-producing of rather rapid decline in the fields of the field. it has 195 wells producing from the southwestern part of the state. Important Michigan Stray sandstone and the Upper extensions were made in Overisel, Porter, Marshall sandstone. This field was devel-Sherman, and Adams fields. Important oil oped on a 40-acre spacing plan, and gas fields of the state are shown on the -map, Fig. I. WiI~dcat Drilling Michigan&apos;s production of 19,700,000 bbl. A test in sec. 29, Winterfield township, during 1940 was 3,800,000 bbl. less than Clare County, which is producing oil from the total for 1939, but about one million the Monroe of Devonian age at a depth of greater than 1938. This brings the total 3760 ft., and a well in sec. 31, Lincoln accumulated production for the state to a township, Osceola County, producing from little over 145,000,000 bbl. the Monroe at 3625 it., should be classed as wildcats that are sure to lead to further Active Oil Fields development in I94L The leading producer for the year was the At the end of the year the Gulf Refining Temple field, Clare County, where 29 new Company&apos;s deep test on the Kawkawlin wells were drilled. The Walker field, Kent structure in Monitor township, Bay County, was second, but drilled 183 new County, was preparing to drill deeper after wells in order to gain that position. In the having had a gas blowout from a depth of extension of the Overisel field in Allegan 7775 ft. This test is the most important one County, 115 new producers were drilled. drilling at the end of the year in Michigan, The Adams field, Arenac County, was for should it develop commercial produc- revived by several wells with initial production from deeper beds it will lead to deeper tions of over 1000 bbl. per day from the drilling on many well-known structures Dundee of Devonian age. that have been producing from shallower sands. Active Gas Fields Two important gas fields were discovered Exploration by Taggart Brothers during the year. The A small amount of reflection seismograph first was in Riverside township, Missaukee work was done in Clare, Osceola, and Glad-Win Counties during the year. Exploration Manuscript received at the office of the Institute March 28 1941 by shallow drilling for structural informa- tion on beds below the glacial drift con- 347

Jan 1, 1941

By Henry M. Howe

THIS paper gives the composition of the iron and slag at different stages in the "air-furnace" process of preparing "hard metal," or white cast-iron, for conversion into malleable cast-iron by annealing. The details of the process are given in an appendix. One of us had been trying for years to work some chemist of some of our malleable-iron works up to a degree of enthusiasm which would lead him to make such au investigation. It would have had the advantage of the greater familiarity with the conditions which one habitually on the spot must have. Failing in this, he made use of an opportunity which presented itself of taking samples here represented, with such fairness as the conditions permitted, holding firmly that a rough approximation to the truth is better than the complete lack of data, or that a bird in the hand is worth two in the bush. We hope that this attempt may stimulate others effectively to duplicate this work, and thus correct or confirm it. Our results are shown in Table I. and graphically in Figs. 1 and 2. Discussion.-At the time when the first two samples were taken, the metal and slag were still too sluggish to permit fair sampling, and not until sample 6 were the conditions really favorable, because at the time of the fourth sample the metal was not fully melted, and even at the time of sample 5 it was still sluggish. Indeed, the slag was probably very heterogeneous throughout, because it took up silica and alumina rapidly from the bottom, and because it was so siliceous as to be sluggish at this relatively low temperature. This hetero-geneousness is exaggerated in the two samples of slag 8, apparently by the great viscosity due to its extraordinary acidity. Note that the manganous oxide of one sample is about two and

Mar 1, 1909

By E. D. Slone, F. L. Dillard

When a new mine is in the planning stages, one of the most important decisions to be made is the selection of&apos; face haulage equipment and the interrelated transportation system to the surface. Equally important is the method of transporting personnel supplies and repair parts from the surface to the working places. When Bell & Zoller management elected to open the new Zeigler mine in the No. 9 seam near Madisonville, Ky., last year, various transportation systems were considered. It was agreed early that a slope mine would be preferred to a shaft mine, and that belt conveyors would be more economical than a rail system.

Jan 1, 1970

New York Meets first Wednesday after first Tuesday of each month. DAVID H. BROWNE, Chairman. PERCY E. BARBOUR, Vice-Chairman A. D. BEERS, Secretary, 55 Wall St., New York, N. Y. C. A. BOHN, Treasurer. Boston Meets first Monday of each winter month. W. E. C. EUSTIS, Chairman. R. L. AGASSIZ, Vice-Chairman. E. E. BUGBEE, Secretary-Treasurer, Mass. Inst. of Technology, Boston, Mass. ALBERT SAUVEUR, H. L. SMYTH. Columbia Holds four sessions during year. Annual meeting in September or October. STANLY A. EASTON, -Chairman. FREDERIC KEFFER, Vice-Chairman. LYNDON K: ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. D. C. LIVINGSTON, FRANK A. ROSS.

Jan 7, 1916

New York Meets first Wednesday after first Tuesday of each month. DAVID&apos; H. BROWNE, Chairman. JOHN H. JANE WAY, Vice-Chairman. F. E. PIERCE, Secretary, 35 Nassau St., New York, N. Y. P. A. MOSMAN, Treasurer. LEWIS W. FRANCIS. BENJAMIN B. LAWRENCE. Boston Meets first Monday of each winter month. HENRY L. SMYTH, Chairman. ALFRED C. LANE, Vice-Chairman. HENRY A. WENTWORTH, Secretary-Treasurer, 60 India St., Boston, Mass. A. H. EUSTIS, F. G. STANTIAL. Columbia Holds four sessions during year. Annual meeting in September or October. STANLY A. EASTON. Chairman. FREDERIC KEFFER, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash.

Jan 3, 1916

By Larry A. Shiprnan

DEMANDS upon power plants by the war program in 1941 intensified problems of coal utilization. It was an outstanding year in that field. The domestic heating stove witnessed outstanding development; the research folks progressing so rapidly that the design of the "perfect" stove is just around the corner. Use of colored motion pictures in analyzing fuel-bed performances has reached a new high with the colored pictures taken at minute intervals and projected at sixteen frames a second as shown by the Koppers Coal Co. and the Anthracite Institute (on domestic stokers) and the Consolidated Edison Co. (industrial stokers). Continued efforts of this kind will be beneficial in analyzing further some of the "Code for Testing Coal" problems confronting Subcommittee No. 2 of the Joint A. I. M. E. - A. S. M. E. Committees.

Jan 1, 1942

By M. A. Hunter

IN the present state of public affairs, the reviewer turns from his traditional role of recording the progress made in research during the year and views the whole situation in which he finds himself in direct relation to the immediate needs of the nation. The slow progress of research year by year fades into comparative insignificance. The sum total of that research in all the years which have past becomes of importance only in direct relation to the extent to which we have translated or can immediately translate it into in¬dustrial production. For in a wartime economy immediacy is of paramount importance. The outcome of the war is being determined by our ability to pro¬duce and fabricate the metals and alloys which we require for its prosecution. Aside from iron and steel which lie outside the limits of this review, the most important of the nonferrous metals now needed in wartime production are aluminum, magnesium, nickel, chromium, and manganese. Some remarks on their production and fabrication follow.

Jan 1, 1942

A GREAT and incomparable speculation is whether the discovery of A compounding the powder used for guns came to its first inventor from the demons or by chance. With this invention he certainly far surpassed all men of every age from the creation of the world up to that day when it was announced by him-men so very learned, indeed like angels and of divine intellect, powerful in every knowledge and power. These had not only revived-arts and sciences and discovered new ones with their intellects, but they had information about all natural

Jan 1, 1942

By L. D. Jaffe

From the limited experimental data in the literature, preliminary values were derived for the thermal diffusivity of titanium alloys and for the quenching severity of various mediums used in heat treating them. The thermal diffusivity, under quenching conditions, was found to be approximately 0.006 sq in. per sec. The quenching severity H for brine is approximately 8, for water 4, for oil 0.9, for air 0.08, and for argon 0.02 in. -&apos; The quenching severity of the Jominy-Boegehold end quench water jet against titanium alloys appeared effectively infinite. Using these results, graphs were prepared showing ideal round sizes and Jominy positions having cooled conditions equivalent to those at the center and surface of titanium alloy rounds, plates, and sheets quenched in various media. THE importance of proper quenching of steel parts has long been recognized, and much quantitative work has been done on the subject. Recently, it has become evident that for titanium alloys, too, the rate of cooling from high temperature is important in obtaining high strength and hardness. Maximum hardness and strength may not be attained in the as-quenched condition but rather after a subsequent tempering or aging treatment. Nevertheless, if cooling from temperatures near the ß transus is too slow, for the hardenability of the alloy used, a soft a-ß structure will be produced which will not harden on subsequent aging.&apos;-" The quenching of parts of practical interest can usually be approximated by simple shapes, such as cylinders (rounds) and plates (or sheets) of various thickness and combinations of these. A standard that has been used extensively for comparison purposes is the center of an ideal round: a cylinder quenched in a medium that instantly cools its surface to room temperature." For steel, considerable practical use has been made of the Jominy-Boegehold end quench hardenability specimen,".&apos; and its value for titanium alloys is becoming evident. It therefore appeared worthwhile to attempt comparison of cooling conditions in titanium alloy rounds and plates of various sizes quenched in various media with cooling conditions in ideal round and Jominy quenches. These comparisons are based upon measurements reported in the literature. Quenching Severity of Jominy Water Jet and of Brine As one starting point, there were available the data of Phillips and Tobin8 for positions on a Jominy specimen having the same hardness as the centers of round bars of various size quenched in 5 pct NaOH brine, shown in Table I. The Jominy speci- men is a round bar, normally 1 in. diam and 4 in. long, quenched by a water jet at one end and air cooled on the other surfaces.&apos; After quenching, hardness is measured vs distance from the quenched end on longitudinal flats ground 0.015 to 0.10 in. deep. The data of Table I were based on a subsized specimen of 3/4 in. diam. Since the positions tested are close to the jet quenched end, cooling there may be taken as due solely to the jet, and air cooling can be neglected. These positions are then equivalent to various locations near one surface of an 8 in. plate jet quenched on both sides. Assuming that the thermal diffusivity is constant and that Newton&apos;s law of cooling holds, temperature vs time curves at corresponding positions in Jominy specimen and round bar then may be calculated for various assumed quenching severities of the water jet and of the brine. Cooling curves are generally taken to be metallurgically equivalent when they show the same time to reach a temperature halfway between the initial (heat treating) temperature and the final (quenching medium) temperature.5 On this basis, using Russell&apos;s tables,9 upplemented by heat flow tables derived in similar fashion by the author for positions near the surface of severely quenched plates, it was found that the experimentally observed equivalence, Table I, was best matched if the quenching severity H of the Jominy water jet was taken as infinite (H = co). This means that the jet quenched surface should be considered as instantly cooled to the temperature of the water

Jan 1, 1956

By Eugene S. Perry

The only outstanding development in Montana oil or gas fields during 1935 was the extension of the Cut Bank oil and gas field 7 miles southward. This field is now about 20 miles long and 3 to 8 miles wide, with 218 producing oil wells and 39 producing gas wells. Average daily production of the oil field during December, 1935, was about 6700 bbl.; total production for the year 1935 was approximately 2,020,770 barrels. The Cut Bank field in northern Montana is in a flat to rolling glaciated area used mainly for grazing purposes. Oil and gas occurs in sandstones and shaly sandstones in the Kootenai (Dakota) formation of Lower Cretaceous age at depths ranging from 2700 to 3000 ft. Prominent anticlinal or domal structure is not present, but small plunging anticlines occur locally. Strata dip westward from 75 to 200 ft. per mile. The field lies on the western flank of the Sweetgrass arch, a broad gentle upwarp over 150 miles long. Localization of oil and gas appears to be due either to pinching or lensing out of the sandstone beds, or else silting of the sandstones with clay minerals so that porosity becomes low. Within the field offset wells show marked variation in initial production, which suggests that differences in porosity of sandstone is the controlling factor. The gas-producing portion of the field is entirely updip (east) from the oil-producing portion, and the producing horizons are the same. Initial production of oil wells ranged from about 50 to about 200 bbl. per day, and initial open flow of gas wells ranged from about one million to about 37 million cubic feet per day, with an average of 11 million cubic feet. Initial gas pressures were slightly greater than 700 lb. per sq. in. Oil is brought to the surface by pumping. Both rotary and standard churn-drilling equipment are used. In the remaining 14 oil and gas fields but little new activity took place other than the drilling of offset wells and wells in proven territory. Continuation of "acid treatment" of wells in the Kevin and Pondera oil fields led to reconditioning of many old wells and the drilling of a number of new wells within these fields. Acid treatment of the oil-bearing horizon, which is the dolomitized and silicified Madison limestone of Mississippian age, has proved quite satisfactory, and some "bone dry"

Jan 1, 1936

By Eugene S. Perry

The only outstanding development in Montana oil or gas fields during 1935 was the extension of the Cut Bank oil and gas field 7 miles southward. This field is now about 20 miles long and 3 to 8 miles wide, with 218 producing oil wells and 39 producing gas wells. Average daily production of the oil field during December, 1935, was about 6700 bbl.; total production for the year 1935 was approximately 2,020,770 barrels. The Cut Bank field in northern Montana is in a flat to rolling glaciated area used mainly for grazing purposes. Oil and gas occurs in sandstones and shaly sandstones in the Kootenai (Dakota) formation of Lower Cretaceous age at depths ranging from 2700 to 3000 ft. Prominent anticlinal or domal structure is not present, but small plunging anticlines occur locally. Strata dip westward from 75 to 200 ft. per mile. The field lies on the western flank of the Sweetgrass arch, a broad gentle upwarp over 150 miles long. Localization of oil and gas appears to be due either to pinching or lensing out of the sandstone beds, or else silting of the sandstones with clay minerals so that porosity becomes low. Within the field offset wells show marked variation in initial production, which suggests that differences in porosity of sandstone is the controlling factor. The gas-producing portion of the field is entirely updip (east) from the oil-producing portion, and the producing horizons are the same. Initial production of oil wells ranged from about 50 to about 200 bbl. per day, and initial open flow of gas wells ranged from about one million to about 37 million cubic feet per day, with an average of 11 million cubic feet. Initial gas pressures were slightly greater than 700 lb. per sq. in. Oil is brought to the surface by pumping. Both rotary and standard churn-drilling equipment are used. In the remaining 14 oil and gas fields but little new activity took place other than the drilling of offset wells and wells in proven territory. Continuation of "acid treatment" of wells in the Kevin and Pondera oil fields led to reconditioning of many old wells and the drilling of a number of new wells within these fields. Acid treatment of the oil-bearing horizon, which is the dolomitized and silicified Madison limestone of Mississippian age, has proved quite satisfactory, and some "bone dry"

Jan 1, 1936

By J. M. Dahl, L. H. Van Vlack

STAFF: Editor, Gerhard Derge Associate Editor, Paul G. Shewman Carnegie lnstitute of Technology Schenley Park Pittsburgh, Pa. 15213 Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: Jack H. Scoff, President; Richard C. Cole, Post-President; Harold B. Emerick, President-Elect; Ralph L. Hennebach, Treasurer; Robert W. Shearman, Secretary; Donald A. Parks, Assistant Secretary; Leslie S. Wilcoxson, Assistant Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: R. E. Lund, Chairman; T. E. Dancy, H. B. Emerick, P. R. Gouwens, R. E. Grace, J. H. Jackson, H. H. Johnson, A. E. Lee, Jr., R. R. Nosh, R. D. Pehlke, and Paul Queneau. Review and selection of monuscripts is under the supervision of the following Publications Committees: Extractive Metollurgy Division: R. E. Grace, Chairman; G. M. Bell, D. W. Bridges, J. M. Cigon, G. W. Healy, T. A. Henrie, R. D. Holli-day, C. E. O&apos;Neill, C. S. Sami s, A. W. Schlech-ten, and Charles Shull . Iron and Steel Division: R. D. Pehlke, Chairman; T. P. Floridis, Arnulf Muon, G. R. St. Pierre, E. T. Tuckdogon, L. H.Von Vlack, and J. M. Uys. Institute of Metals Division: H. H. Johnson, Jr., Chairman; J. B. Clark, Vice Chairman; M. R. Achter, G. F. Bolling, J. O. Brittain, G. P. Conard, II, L. A. Girifolco. G. T. Hahn, J.P. Hirth, L. Himmel, G. T. Horne, George Krauss, C. F. Leitton, Jr., J. D. Livingston, R. D. Monning, H. M. Otte, S. V. Radcliffe, R. E. Reed-Hill, H. C. Rogers, O. Sherby, M. T. Simnod, G. R. Speich, E. A. Steigerwold, R. A. Swolin, W. A. Tiller, W. R. Upthegrove, J. B. Wagner, Jr., Derek Walton, H. W. Weart, W. W. Webb, and D. WiIsdorf. Published monthly by the American lnstitute of Mining, Metollurgicol, and Petroleum Engineers, Inc., 345 East 47th Street, New York, N. Y. 10017. Telephone PLAZA 2-6800. Subscription $30 per year for non-AIME members in United States and North, South, and Central America; $32, foreign; $7.50 for AlME members. Single copies, $6.00, single copies foreign, $6.50. The AlME is not responsible for any statement mode or opinion expressed in its publications . . . Copyright 1965 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . . . Registered cable address, AlME New York . . . Indexed in Engineering Index, lndustrial Arts Index, and Chemical Abstracts . . Second class postage paid at New York, N. Y., and Ann Arbor, Mich. Volume 233, Number 1.

Jan 1, 1965

By Jay A. Carpenter

WAR?S impact on Nevada mining and rnetallugrcal operations has brought about a rapid rise in the gross value of the ores mined and milled for the atratezic metals, and a sharp decrease in that for the precious metals. The State?s total production over the present war years will averaged out 10 per cent above the good record of $39,000,000 in 1937. However. this annual production is low in contract to that of nearly $47,000,000 in 1877 in the days of the great bonanza on the Comstock, and that of nearly $49,000.000 in 1918 during the last World War..

Jan 1, 1944

By H. W. Imholz

Active interest in the North Central Texas area centered in the development of the Palo Pinto limestone-producing zone, near the town of Avoca, in the northeast part of Jones County. This producing horizon was discovered in 1937, in the Iron Mountain Oil Company&apos;s well No. 1 Olander, in sec. 196, B.B.B. & C. survey, at 3238 to 3250 ft. During the development of this pool, it was generally referred to as the Avoca pool. As a second pool has been discovered in the same producing zone, also near the town of Avoca, the writer has taken the liberty of changing the name of the original Avoca pool to Avoca-Olander pool. Forty producers had been drilled in the Avoca-Olander pool by the end of 1938; their initial ranged from 28 to 300 bbl. per hour. Stimulus was given to the interest in the development of the Palo Pinto limestone when the Ungren-Frazier No. 1 Griffin, in sec. 199, B.B.B. & C. survey, Jones County, found the limestone from 3225 to 3250 ft., with an initial production of 931 bbl. per day. (This new pool has been given the name of Avoca-Griffin pool, by the writer.) The best well to be completed, up to the present time, is the Bert Fields No. 1 Taylor in sec. 199, B.B.B. & C. survey, which had an initial production of 748 bbl. in 3 hours. The Owen-Snebold No. 1 McKeever in sec. 158, B.B.B. & C. survey, in northwest Shackelford County, added to the interest in the Palo Pinto limestone when it extended the Ivy pool with a well in the Palo Pinto limestone from 3145 to 3183 ft., and was estimated good for 6,000,000 cu. ft. of gas and 6000 bbl. of oil per day. During 1938, Stonewall County obtained its first commercial producer when the Stonewall Oil Co. in No. 1 Parriott discovered the Palo Pinto limestone saturated from 5169 to 5176 ft. and tested 371 bbl. per day. Two new producing horizons were discovered about 2 miles east of the old Noddle Creek pool, Jones County; the first, the Humble Oil & Refining Co. No. 1 Irvin, in sec. 48, block 18, T. & P. R. R. Co. survey, which had saturated limestone from 2550 to 2567 ft. and was good for 100 bbl. per day; the second, in the Humble No. 1 Horton, sec. 40, which

Jan 1, 1939

By H. W. Imholz

Active interest in the North Central Texas area centered in the development of the Palo Pinto limestone-producing zone, near the town of Avoca, in the northeast part of Jones County. This producing horizon was discovered in 1937, in the Iron Mountain Oil Company&apos;s well No. 1 Olander, in sec. 196, B.B.B. & C. survey, at 3238 to 3250 ft. During the development of this pool, it was generally referred to as the Avoca pool. As a second pool has been discovered in the same producing zone, also near the town of Avoca, the writer has taken the liberty of changing the name of the original Avoca pool to Avoca-Olander pool. Forty producers had been drilled in the Avoca-Olander pool by the end of 1938; their initial ranged from 28 to 300 bbl. per hour. Stimulus was given to the interest in the development of the Palo Pinto limestone when the Ungren-Frazier No. 1 Griffin, in sec. 199, B.B.B. & C. survey, Jones County, found the limestone from 3225 to 3250 ft., with an initial production of 931 bbl. per day. (This new pool has been given the name of Avoca-Griffin pool, by the writer.) The best well to be completed, up to the present time, is the Bert Fields No. 1 Taylor in sec. 199, B.B.B. & C. survey, which had an initial production of 748 bbl. in 3 hours. The Owen-Snebold No. 1 McKeever in sec. 158, B.B.B. & C. survey, in northwest Shackelford County, added to the interest in the Palo Pinto limestone when it extended the Ivy pool with a well in the Palo Pinto limestone from 3145 to 3183 ft., and was estimated good for 6,000,000 cu. ft. of gas and 6000 bbl. of oil per day. During 1938, Stonewall County obtained its first commercial producer when the Stonewall Oil Co. in No. 1 Parriott discovered the Palo Pinto limestone saturated from 5169 to 5176 ft. and tested 371 bbl. per day. Two new producing horizons were discovered about 2 miles east of the old Noddle Creek pool, Jones County; the first, the Humble Oil & Refining Co. No. 1 Irvin, in sec. 48, block 18, T. & P. R. R. Co. survey, which had saturated limestone from 2550 to 2567 ft. and was good for 100 bbl. per day; the second, in the Humble No. 1 Horton, sec. 40, which

Jan 1, 1939

By W. S. Ayres

[Secretary&apos;s Note.—At the Spokane meeting of the Institute, in discussion of President Brunton&apos;s address on "Modern Progress in Mining and Metallurgy in the Western United States," and at the request of members present, Mr. Ayres gave an oral account of his new separator, which is here published as an independent paper, partly because of its inherent importance and partly because it describes an improvement which did not originate in the Western United States, and therefore does not fall, strictly speaking, under the title of President Urunton&apos;s address.—R. W. R.] A brief history of the growth of the anthracite-coal preparation will give a better view-point from which to judge the present problem of separating slate from coal. At the beginning of the commercial value of anthracite, 70 years ago, only the pure portions, or " splits," of the veins were mined and shipped to market, and without any preparation or screening other than the selection, while loading, of the glassy lumps, and the rejection of the fine material and the slate that had strayed accidentally into the coal. The next step was the crushing or breaking of the coal (hence the name "breaker" as applied to the preparation-building), and the sizing of it by means of bars or revolving screens. This stage of its development marked the advent of the " breaker-boy " as a slate-picker, with his ever-increasing capriciousness. As the richer veins or a splits " became exhausted and the market demanded a still greater output, the less-pure " splits " and the thinner veins were utilized to produce the coal. Carrying as they do a far greater percentage of impurities, particularly when removing the pillars, it became necessary to build new and better equipped preparation-plants. Finally, we are now at the highest stage of complicatioii yet known to the art of coal-preparation. We are dealing with varying specific gravities, frictional difference, hardness, structure, and form in the pieces of coal and slate coming from many different veins, and

Jan 1, 1910

By Thomas W. Dawson

The H. C. Frick Coke Co. has used belt conveyers for handling coal for the last eighteen years but, until recently, only for small tonnages and over short distances. The first installations were outside the mines for distributing coal to various parts of plants. A belt conveyer was put in service at Colonial No. 4 Mine in November, 1906, to carry coal from the main hoisting shaft to a storage bin serving two blocks of beehive ovens on the other side of the valley; it was in constant service until the Colonial No. 4 ovens were abandoned less than a year ago. This conveyor was in an overhead gallery that spanned our sidings and yard tracks and the main line of the Pennsylvania Railroad. It was a crude installation, from the viewpoint of present conveyor engineering practice. It had no mechanical feeding device, the coal simply ran through a gate in the side of a bin on to the belt; but one belt on this conveyor lasted eleven years. This conveyor is about 300 ft. long center to center of pulleys. It operated at a speed of 250 ft. &apos;per min-and carried about 400 tons per day. On this basis, the belt life of eleven years means that not over a million and a quarter tons was carried by the belt. whi1e: this is not a large tonnage, the cost per ton was much less than by any previous method in use for supplying coal to ovens located at a distance from the main shaft. The next belt conveyor was installed at Bridgeport Mine in 1907. It carried about the same daily tonnage as the first, delivering from the hoisting shaft to a coke-oven bin. Very few data were kept on this conveyor. It also operated until the coke ovens at the plant were put out of blast and the coal taken to the Clairton byproduct plant by river. In 1916, work was started to equip the Bridgeport, Palmer, Gates, and Ronco mines to load their entire output on the river for transportation to the Clairton byproduct plant, which was then being built. These mines were all operating at that time and had a large area of coal available for river shipment. The Monongahela Railroad was located between the hoisting shaft and the river at each of these plants and, therefore, had to be crossed at each location to deliver coal to the river. After careful study, it was decided to transport this coal from the hoisting shaft to the river at each of these plants by belt conveyors.

Jan 1, 1925

YEAR OF ELECTION 1913. FRANK DAWSON ADAMS Montreal, Canada. 1921. WILLIAM CUTHBERT BLACKETT Sacriston, Durham, England. 1923. GELASIO CAETANI Rome, Italy. 1929. TAKUMA DAN Tokyo, Japan. 1920. HENRY STURGIS DRINKER Merion Station, Pa. 1922. FEDERICO GIOLITTI Torino, Italy. 1906. SIR ROBERT A. HADFIELD London, England. 1928. JOHN HAYS HAMMOND New York, N. Y. 1921. FRANK WILLIAM HARBORD London, England. 1917. HERBERT HOOVER Washington, D. C.. 1905. HENRI LECHATELIER Paris, France. 1900. WALDEMAR LINDGREN Cambridge, Mass. 1879. JOHN MARKLE New York, N. Y. 1921. C. MCDERMID London, England. 1913. EZEQUIEL ORDONEZ Mexico City, Mexico. 1909. ALEXANDRE POURCEL Paris, France. 1911. ROBERT H. RICHARDS Cambridge, Mass.

Jan 1, 1923