Search Documents

By Charles Wurms, Robert Steinitz

DURING an investigation to determine the compatibility of several metals with tungsten, the degree of reaction between tungsten and lead was determined. A literature survey showed considerable disagreement between the results of various earlier investigators. Information presented by M. Hansen1 states that, according to S. Inouye,2 tungsten has very poor resistance against attack by molten lead, even at the low temperature near the melting point of lead. A phase diagram in the same reference indicates a solubility of 30 wt pct W in molten lead at 1300°C. Contrary evidence was shown by Parkman and shepard3 in their investigation of materials for use in heat transfer systems containing liquid lead alloys; they performed experiments at 980°C for times up to 50 hr without noticing any appreciable attack on the tungsten. Tungsten sheet was immersed in molten lead contained in Vycor tubes evacuated to at least 10-4 mm Hg. R. Bernard4 and R. I. Jaffee5 also indicate that no reaction occurs between molten lead and tungsten. However, no experimental data were included in these reports. In order to settle the question of the solubility of tungsten in molten lead, tungsten powder with an average Fisher subsieve particle size of 6µ was pressed in a double-acting die at 6 tsi to small compacts. They were then sintered in an atmosphere of hydrogen for 2 hr at 1700°C, resulting in a sintered density of 64 pct of theoretical with final dimensions of 0.260 in. in height and 0.245 in. in diameter. For all tests, the tungsten pellets were immersed in molten lead. Table I is a summary of the experimental procedures showing atmospheres, temperatures, and times. The first experiments were performed at 650°C; at this temperature, the liquid lead should wet the porous tungsten better than at its melting point, and penetrate into the pores. The lead was heated in a graphite crucible with a graphite cover. No protective atmosphere was used, as it was expected that the formation of CO would be sufficient to prevent oxidation. This, however, proved to be wrong, and all tungsten samples showed a slight oxide film after treatment. The tungsten samples were immersed in the molten lead for times of 5 min, 10 min, 1/2 hr, 1 hr, and 2 hr. After this time, the melt was poured into a form and the

Jan 1, 1962

By Alexander Knoll, Dwight L. Baker

THIS paper is a report on work undertaken to investigate the results and conclusions of Ravitz and Porter1,2 that galena freed of surface oxidation products and lead carbonate ("clean" galena) is waterrepellent, and that the action of xanthates in flotation is the action of a cleansing agent, enabling oxidized galena particles to expose a pure lead sulphide, water-repellent surface. The apparatus, in construction and use, was essentially that of Ravitz and Porter. The only significant modification introduced by the present authors was the substitution of a three-necked flask for the flotation cell as the "reaction vessel." Our procedure was to place 50 grams of freshly ground, minus 200-mesh galena in the reaction vessel, sweep out all molecular oxygen from the system with oxygen-free nitrogen, and proceed to wash the galena surface free of its oxidation products with repeated small portions of (I) ammonium acetate (500 c.c. of water, 200 grams of ammonium acetate) or (2) ammonium chloride, hydrochloric acid (2 liters containing 200 grams of ammonium chloride and 25 c.c. Of 1.18 sp. gr hydrochloric acid). The galena was next washed with many 100-c.c. portions of oxygen-free, distilled water. The galena was finally considered free of soluble salts when wash water that had been in contact with the mineral for at least 48 hr.* gave negative tests for: (x) lead ion with sulphide; (2) chloride with silver ion; (3) acetate with cuprous chloride, sodium chloride; and (4) ammonium ion with Nessler's reagent. Next 500 c.c. of potassium ethyl xanthate solution, free of dissolved oxygen, was run onto the "clean" galena particles. For this system there were determined: I. The wetting properties of the clean galena particles by shaking the reaction flask and noting the degree of mineral collection at the liquid-air interface. This was, of course, simply a qualitative test, but it proved adequate for our purpose. 2. The removal of xanthate ion from the potassium xanthate solution on being shaken with the "cleansed" mineral. Xanthate concentrations were determined by iodine titration according to the methods of Taylor and Knoll.3 3. The pH of the xanthate solution after having been shaken with the "cleansed" galena. The pH was determined colorimetrically.4 The results of five experiments of the type mentioned above are given in Table x.

Jan 1, 1941

By E. C. Truesdale

IN recent years various problems in connection with research work on the preparation and properties of zinc-base alloys have required reliable information concerning the constitution of the zinc-rich portion of the iron-zinc equilibrium diagram. On numerous occasions rather positive indications were obtained that, for example, the solubility of iron in zinc was incorrectly represented on the current equilibrium diagrams. A careful study of all the available literature relating to the iron-zinc system led to the conclusion that much of the early work was unsatisfactory as measured by present standards of experimental accuracy, and as a result it was decided to redetermine the location of the liquidus curve and of adjacent portions of the diagram. Part I of this paper comprises a description of the experimental methods and a summary of the results by means of which the zinc-rich end of the iron-zinc diagram has been revised in the following ways: 1. Measurements of the solubility of iron in liquid zinc by several different sampling methods, leading to a relocation of the liquidus curve. 2. Microscopic, conductivity, and X-ray studies of the solid solubility of iron in zinc, which, together with thermal analyses, have resulted in new values for the solid solubility and the eutectic temperature and composition. 3. Heating and cooling curves, obtained by a refined differential method, leading to new locations for the two peritectic horizontals. In Part II of the paper the attempt is made to review all of the pub-lished work having a bearing on the constitution of the iron-zinc system, and to correlate the present results, and some recently published data

Jan 1, 1935

By W. R. Finlay, W. R. Jr. Hibbard

The key feature of the lattice coherency theory of precipitation hardening1 is the forced coherence between matrix and precipitate which elastically strains both lattices and is believed to be the major source of strengthening in precipitation hardening. In systems exhibiting age hardening, the atom movements leading to precipitation are not at all extensive and are such as to require the minimum amount of energy to produce the interface; that is, the new lattice forms in such a way as to be as nearly as possible a continuation of the old with a matched, coherent plane at the interface at least during the initiation of the precipitation. The crystallographic sequence whereby regions of the matrix change to the precipitate lattice usually can be resolved into a set of shearing operations.6'6 Conversely, the perhaps novel speculation is made that solution of a second phase is accompanied by shearing movements which are possibly the reverse of the precipitation shearing movements. A basic premise of the investigation reported in this paper is that precipitation and solution shearing movements constitute structural weaknesses which might cooperate with applied stresses to facilitate plastic deformation. Another basic premise of the investigation is that the application of hydrostatic pressure to a precipitation hardening system will significantly alter the degree of disregistry across the matrix-precipitate interface and thereby significantly affect the course of age hardening. Two binary precipitation hardening systems were investigated: rz pct zinc in aluminum which undergoes transformations, both precipitation and solution, by a simple crystallographic mechanism; and 4 pet copper in aluminum which undergoes a complex transformation in precipitating and dissolving a second phase. The effects of the application of uniaxial tensile creep stress during elevated temperature aging of both systems and of hydrostatic pressure during the elevated temperature aging of 12 pct aluminum-zinc were then investigated. Previous Investigations Van Wert in 1935,~ studied the effect of hydrostatic pressure on the room temperature age hardening of a few precipitation hardening systems. The latter were rather unfortunately selected since none is known to exhibit any marked volume change on aging and the majority were complex commercial alloys the precipitation mechanisms of which are not known. Jenkins, Bucknall and Jenkins~n,~ in 1944, applied tensile creep stresses to a complex copper. nickel-silicon alloy at various temperatures. The complexity of the alloy and the industrial objective of the work did not permit an appreciable addition to the theoretical understanding of either deformation or precipitation hardening.

Jan 1, 1949

By J. M. Callow

H. A. MEGRAW, New York, N.,Y.-One interesting thing that might be brought out in this connection is the cost of making sulphide gas. I had a communication the other day which suggested that, in view of the high cost of oil, sulphur and sodium sulphide, we might make use of a well-known chemical reaction to form this sulphide gas by the use of aluminum sulphide. It is difficult to see any advantage in this, however, since aluminum has been affected just as much as any other commodity by the rise in prices, due, to war conditions. RUDOLF GAHL, Miami, Ariz. (communication td the Secretary*) Mr. Callow refers to my paper, History of Flotation at Inspiration, which was presented at the Arizona meeting of the Institute. These notes of Mr. Callow's contain much valuable information on flotation practice, as is to be expected from an article written by an author of Mr. Callow's experience in this branch of metallurgy. Nevertheless, I cannot help contradicting a number of the statements made in the references to my paper. In passing, I will also say a word about the reference in Mr. Callow's paper to the article by Messrs. Laist and Wiggin entitled "Flotation Concentration at Anaconda, Mont." Mr. Callow calls attention to the fact that evidently Callow flotation machines are not very sensitive, inasmuch as one man per shift handles four 800-ton sections of Callow machines or 3,200 tons per day at the Inspiration plant. While-it has been the experience of the Inspiration company that the four sections of Callow machines in the Inspiration concentrator are easily handled by one American operator per shift, it is only fair to state that each man operating four sections is assisted by two Mexican helpers who constantly clean the bottoms of the machines. The tonnage per section, by the way, whether equipped with Callow,, Inspiration or Minerals Separation machines, is considerably in excess 4 800 tons.. Mr. Callow further says that local opinion at Inspiration is that, two 800-ton sections consisting of two 10-compartment and four 6-compartment Minerals Separation machines (these machines are of the Hebbard type) is the limit that one man can properly attend. I do not hesitate to say that I consider it perfectly feasible to have four such sections operated by one man, perhaps assisted by "one helper. The Minerals Separation machines of this type have undoubtedly an advantage as far as easiness of operation is concerned,

Jan 4, 1917

The following letter has been received from the Chairman of the United States Shipping Board. August 1, 1918. American Institute of Mining Engineers, New York, N. Y. GENTLEMEN: I am going to call upon your organization for some teamwork. The time has come for Americans everywhere to put themselves solidly behind American ships. Our railroads must no longer stop at the ocean. We are building an American merchant fleet of twenty-five million tons-three thousand ships. We are backing modern ships with modern port facilities, establishing our bunkering stations all over the globe and will operate with American railroad efficiency. We will carry American cargoes at rates corresponding to our railroad rates-the cheapest in the world. Fast American passenger-and-cargo liners will run regularly to every port in Latin America, the Orient, Africa, Australia. Are you taking steps to use these ships to increase your own prosperity? Do you realize that American products of factory, farm and mine can be delivered to customers in foreign countries on terms which will build lasting trade? Do you realize the possibilities for bringing hack raw materials to extend your products and trade? We must all take off our coats and work to bring these American ships home to the people of every American interest and community. The manufacturer must think of customers in Latin America as being as accessible as those in the next state. The farmer must visualize ships carrying his wheat, cotton, breeding animals, dairy products and fruit to new world markets. The American boy must think of ships and foreign countries when he chooses a calling.

Jan 9, 1918

By M. King Hubbert

DURING the past summer the writer was asked by the Illinois State Geological Survey to make a study of some of its economic geological problems with regard to the applicability of geophysical methods of prospecting to their solution. The following four problems were sug-gested for investigation: (1) the fluorspar area of Southern Illinois, (2) oil structures in the south central part of the state, (3) the lead and zinc-bearing area of northwestern Illinois, and (4) the water supply and gravel deposits of the glacial drift. The prime requirements were to find a means of obtaining a maximum of useful information with a fairly modest outlay of expenditure for technical staff and equipment. The method of procedure adopted was that of making a preliminary study of each of the problems named by means of available office data and published reports with supplementary field reconnaissance where necessary.

Jan 1, 1932

Three years ago, when Sun Energy Development Co. (Sunedo) dedicated its Cordero mine in Wyoming, the company noted that its decision to venture into the coal industry was prompted by the need for domestic energy self-sufficiency. Now, as the energy situation assumes crisis proportions and the cry For coal intensifies, Sunedoo has begun a $21 million expansion program that will double the mine's productive capacity by the mid-1980s. When the Cordero come was originally conceived, Sunedoo obtained permission from permitting authorities to produce up to 11 million t/y (12 million stpy) of coal. But seeing opportunities in the coal market, Sunedoo returned to the agencies in 1976 and came away with permission to produce 22 million t/y (24 million stpy). Of that total permitted capacity, Cordero is expected to produce about 3.6 million tons (4 million st) this year.

Jan 9, 1979

By J. S. Kennedy, A. A. Lerew, C. M. Judson, G. L. Simard

DITHIOPHOSPHATE collectors are commonly used in the flotation of sulphide minerals. Studies of the interaction of a typical dithiophosphate collector with galena surfaces have been previously reported from. these laboratories." These fundamental studies were carried out by employing phosphorus labeled radioactive dithiophosphate. Radioactivity determinations then could be used to measure readily and accurately the small concentrations of dithiophosphate that, are present under conditions of flotation processes. Measurements were made on ground mineral, determining the amount sorbed indirectly from the concentrations in solution; and studies were also made with single crystals, determining the amount sorbed directly by counting the crystal surface. The rates, isotherms and reversibility characteristics of dithiophosphate sorption, the competition between phosphate and dithiophosphate for the mineral surface, and the exchange of sorbed dithiophosphate with dissolved dithiophosphate were studied. These studies have now been extended by sorption measurements in flotations with a Fagergren, machine. For this work, the selective flotation of galena and sphalerite from quartz was chosen, using ammonium di-(sec-butyl) dithiophosphate as. the collector, sodium cyanide as depressant for sphalerite, and copper sulphate as an activator for sphalerite. While the selective flotation of galena and sphalerite using a single dithiophosphate collector is not typical of flotation practice (two different collectors are generally used), it was found that a reasonably good separation could be obtained by using zinc sulphate with the sodium cyanide in the galena flotation and by cleaning the sphalerite concentrate or by carrying out the sphalerite. flotation in an alkaline medium. Data of practical importance on the distribution of collector between the concentrates, tailings, and solutions were obtained, particularly with regard to the effect of copper sulphate and sodium cyanide. In addition to the. selective flotation of galena and sphalerite from quartz, single flotations of galena-quartz and sphalerite-quartz mixtures were carried out, along with blank flotations on quartz alone. The present paper describes the results of these experiments. As in previous papers, the term sorption is used to designate uptake of collector by the mineral, without implication as to the nature of the processes involved. Experimental Materials: The mineral system was a ground synthetic mixture of galena, sphalerite, and quartz. The galena was from Galena, Kans., and contained 75 pct lead (theoretical 85.6 pct Pb for PbS); the sphalerite, from Ottowa County, Okla., contained 63 pct zinc (theoretical 67.2 pet Zn for ZnS) ; and the quartz from Klondike, Mo., analyzed as 99.97 pet SiO2. Sulphur labeled radioactive di-(sec-butyl) dithiophosphate was prepared from S82 supplied by the Oak Ridge National Laboratory on allocation from the U. S. Atomic Energy Commission. The synthesis consisted of precipitating barium sulphate, reducing the barium sulphate to barium sulphide, acidifying to form hydrogen sulphide, and oxidizing the hydrogen sulphide with iodine to elemental sulphur.

Jan 1, 1952

By J. H. Berryman

THE use of oxygen as a bath reagent in hearth furnaces during the refining period is a familiar story. Investigations and tests in which oxygen was substituted for iron ore to reduce carbon date back 25 years and include the work of Bigge,1 Browne,2 and Chelius.3 During this past year the majority of the experimental work in the use of oxygen was carried on mainly in open-hearth shops, since it was felt that the greater field for application lay in this type of furnace. Much constructive work was done in evaluating the carbon-oxygen relationships, as reported by Slottman and Lounsberry4 and by Hughes.5 Steelmakers using the electric furnace have been actively engaged meanwhile in an experimental program of their own, with such success that the oxygen injection pipe has become a tool in the day to day production of low-carbon and stainless steels.

Jan 1, 1947

By J. S. Kennedy, G. L. Simard, A. A. Lefrew, C. M. Judson, R. B. Booth

DITHIOPHOSPHATE collectors are commonly used in the flotation of sulphide minerals. Studies of the interaction of a typical dithiophosphate collector with galena surfaces have been previously reported from these laboratories.'* These fundamental studies were carried out by employing phosphorus labeled radioactive dithiophosphate. Radioactivity determinations then could be used to measure readily and accurately the small concentrations of dithiophosphate that are present under conditions of flotation processes. Measurements were made on ground mineral, determining the amount sorbed indirectly from the concentrations in solution; and studies were also made with single crystals, determining the amount sorbed directly by counting the crystal surface. The rates, isotherms and reversibility characteristics of dithiophosphate sorption, the competition between phosphate and dithiophosphate for the mineral surface, and the exchange of sorbed dithiophosphate with dissolved dithiophosphate were studied. These studies have now been extended by sorption measurements in flotations with a Fagergren machine. For this work, the selective flotation of galena and sphalerite from quartz was chosen, using ammonium di-(sec-butyl) dithiophosphate as the collector, sodium cyanide as depressant for sphalerite, and copper sulphate as an activator for sphalerite. While the selective flotation of galena and sphalerite using a single dithiophosphate collector is not typical of flotation practice (two different collectors are generally used), it was found that a reasonably good separation could be obtained by using zinc sulphate with the sodium cyanide in the galena flotation and by cleaning the sphalerite concentrate or by carrying out the sphalerite flotation in an alkaline medium. Data of practical importance on the distribution of collector between the concentrates, tailings, and solutions were obtained, particularly with regard to the effect of copper sulphate and sodium cyanide. In addition to the selective flotation of galena and sphalerite from quartz, single flotations of galena-quartz and sphalerite-quartz mixtures were carried out, along with blank flotations on quartz alone. The present paper describes the results of these experiments. As in previous papers, the term sorption is used to designate uptake of collector by the mineral, without implication as to the nature of the processes involved. Experimental Materials: The mineral system was a ground synthetic mixture of galena, sphalerite, and quartz. The galena was from Galena, Kans., and contained 75 pct lead (theoretical 85.6 pct Pb for PbS); the sphalerite, from Ottowa County, Okla., contained 63 pct zinc (theoretical 67.2 pct Zn for ZnS); and the quartz from Klondike, Mo., analyzed as 99.97 pct SiO,. Sulphur labeled radioactive di-(sec-butyl) dithiophosphate was prepared from SS supplied by the Oak Ridge National Laboratory on allocation from the U. S. Atomic Energy Commission. The synthesis consisted of precipitating barium sulphate, reducing the barium sulphate to barium sulphide, acidifying to form hydrogen sulphide, and oxidizing the hydrogen sulphide with iodine to elemental sulphur.

Jan 1, 1953

By J. S. Kennedy, A. A. Lefrew, C. M. Judson, R. B. Booth, G. L. Simard

DITHIOPHOSPHATE collectors are commonly used in the flotation of sulphide minerals. Studies of the interaction of a typical dithiophosphate collector with galena surfaces have been previously reported from these laboratories.'* These fundamental studies were carried out by employing phosphorus labeled radioactive dithiophosphate. Radioactivity determinations then could be used to measure readily and accurately the small concentrations of dithiophosphate that are present under conditions of flotation processes. Measurements were made on ground mineral, determining the amount sorbed indirectly from the concentrations in solution; and studies were also made with single crystals, determining the amount sorbed directly by counting the crystal surface. The rates, isotherms and reversibility characteristics of dithiophosphate sorption, the competition between phosphate and dithiophosphate for the mineral surface, and the exchange of sorbed dithiophosphate with dissolved dithiophosphate were studied. These studies have now been extended by sorption measurements in flotations with a Fagergren machine. For this work, the selective flotation of galena and sphalerite from quartz was chosen, using ammonium di-(sec-butyl) dithiophosphate as the collector, sodium cyanide as depressant for sphalerite, and copper sulphate as an activator for sphalerite. While the selective flotation of galena and sphalerite using a single dithiophosphate collector is not typical of flotation practice (two different collectors are generally used), it was found that a reasonably good separation could be obtained by using zinc sulphate with the sodium cyanide in the galena flotation and by cleaning the sphalerite concentrate or by carrying out the sphalerite flotation in an alkaline medium. Data of practical importance on the distribution of collector between the concentrates, tailings, and solutions were obtained, particularly with regard to the effect of copper sulphate and sodium cyanide. In addition to the selective flotation of galena and sphalerite from quartz, single flotations of galena-quartz and sphalerite-quartz mixtures were carried out, along with blank flotations on quartz alone. The present paper describes the results of these experiments. As in previous papers, the term sorption is used to designate uptake of collector by the mineral, without implication as to the nature of the processes involved. Experimental Materials: The mineral system was a ground synthetic mixture of galena, sphalerite, and quartz. The galena was from Galena, Kans., and contained 75 pct lead (theoretical 85.6 pct Pb for PbS); the sphalerite, from Ottowa County, Okla., contained 63 pct zinc (theoretical 67.2 pct Zn for ZnS); and the quartz from Klondike, Mo., analyzed as 99.97 pct SiO,. Sulphur labeled radioactive di-(sec-butyl) dithiophosphate was prepared from SS supplied by the Oak Ridge National Laboratory on allocation from the U. S. Atomic Energy Commission. The synthesis consisted of precipitating barium sulphate, reducing the barium sulphate to barium sulphide, acidifying to form hydrogen sulphide, and oxidizing the hydrogen sulphide with iodine to elemental sulphur.

Jan 1, 1953

By V. R. Thompson, R. C. Westgren

In a recent paper,1 the solid-solution strengthening of tungsten and tantalum in a portion of the W-T;-MO-C~ alloy system was described. Additions of tantalum and columbium to tungsten led to significant strengthening, and the introduction of dispersions into these alloys was suggested as a means of further increasing strength. Dispersion strengthening of columbium and molybdenum alloys has been studied extensively.2-4 The approach used to dispersion-strengthen molybdenum alloys appeared equally suitable for tungsten alloys, and, therefore, a brief study was undertaken to determine to what extent the introduction of carbide dispersions would strengthen a solid-solution tungsten-base alloy. A base composition of tungsten and 10 to 12 pet Cb was selected; previous work1 had shown that the tensile strength of this solid-solution alloy was 50,000 psi at 3000°F. For the study of the effects of small additions of

Jan 1, 1964

By John E. Sweet

There have already been so many subjects of a purely mechanical nature presented to the Institute of Mining Engineers, that it is unnecessary for me to apologize for adding another to the list. When a new invention, or what is supposed to be a new invention, claiming simply an improvement on the well-known devices, is to be described, it is usual to point out the defects of the old and give a history of the object or the art up to date. But, as no doubt a large proportion of the members of this Institute know as much, or more, about the history and use of the steam-engine indicator than I do myself, I will not further preface the subject, than to remind you that what called for the Richards's improvement on the Watt's indicator was high speed; that the leading improvement was the reduction of momentum in the reciprocating parts; and that this was accomplished by making the parts lighter, and reducing the travel of the heaviest, of them, and consequently the speed and momentum. The use of the indicator has been extended, for the speed of steamengines and other prime movers has been increased, until one engineer at least, John Cooper, of Philadelphia, says, "I want an indicator that will work up to a thousand revolutions." .Mr. Thompson, of the Buckeye Steam-Engine Company, of Salem, Ohio, has improved on the Richards's indicator by another reduction in the momentum, which is done by putting the parallel motion nearer the fulcrum of the pencil arm, reducing both weight and travel. The characteristic feature of the indicator I am going to illustrate is a still further reduction in the same direction, which is accomplished by dispensing with the parallel motion altogether. As is often the. case, in putting a simple idea into shape, some difficulties

Jan 1, 1879

Bureau of Mineral and Topographic Survey, University of Kentucky, Lexington, Ky. Arthur C. McFarlan, State Geologist The Kentucky Geological Survey was abolished by a recent legislative act and the Bureau of Mineral and Topographic Survey at the University of Kentucky was created in its place Publications of the former Survey are distributed by the present Bureau Several series of papers and volumes have been issued but only those of Series 3, 4 and 6 are now to be had in whole or in part Of Series 4, (1912-18) only one group of papers is available Vol: 1, pt. 2, Miscellaneous papers on fire clays, limestones and coals of parts of the state (1913), $125. Of Series 3 (1904-1912), the following bulletins are pertinent and may be had. Bulletin 3, Coals, clays, etc., of Kentucky (1905), 50 cents, 14, Coals of the Pineville Gap region (1912), $1.25, 16, The Waverlain formation of east central Kentucky (1912), 50 cents, 17, Coals of the Tradewater region (1912), 50 cents, 18, Coals of Quicksand region (1912), 50 cents; 19, Geology and coals of the Central City, Madisonville, Calhoun, and Newberg Quadrangles (1912), 50 cents

Jan 1, 1933

By Paul A. Beck

It is well known that the hardness of metallic single crystals, like that of polycrystalline metals, increases during deformation (hardening by cold-work). It is also known that, as a consequence of deformation. the metallic material acquires an evident thermodynamic instability, revealed, for example, by the fact that the increased hardness gradually decreases with time, especially at elevated temperatures (softening by annealing). The temperature at which the stabilizing process begins is different for various metals, and for any metal it depends on the amount of deformation. Such stabilization of deformed metals may proceed in two different ways: through recovery, and through recrystallization. The former process allows the unstable deformed metal body to approach stability gradually and without visible change in the grain structure; the latter process, like an allotropic transformation, yields directly the undeformed stable "phase" in the form of new undeformed crystals, which, starting out of a certain number of nuclei, grow into and " consume " the deformed hard material. The extent of stability attainable through recovery is limited, especially if the deformation of the metal crystal or crystals involves not only the gliding along slip planes, but also the bending of the slip lamellae, or at any rate the bending of comparatively large parts of the crystal lattice. In such cases, for instance in bent single crystals or polycrystalline metals subjected to any deformation, recovery will not as a rule be able to restore the "istraight" undeformed lattice, and stability can be attained only by recrystallization; that is, by the consumption of the bent crystal lattice parts by new, undeformed crystals—a much more drastic process. It is evident that the part of the surplus free energy stored in deformed crystals, which is present in the form of the elastic energy of the bent lamellae, is in these instances not considerably involved

Jan 1, 1937

By James F. McDivitt

The mineral industry of today is faced with a number of dilemmas, not the least of which grows out of the series of related facts-world mineral consumption is growing, and is expected to continue to grow; maintaining adequate capacity to meet needs will require very great capital investment over the next decades, investment which must be measured in billions of dollars; much of the new production must come from remote and relatively underdeveloped countries; many of the areas in which such development must take place are not areas in which private capital enters without some trepidation. There are real problems in financing new mineral development-problems which have occupied the thoughts of many in the industry. One group which is currently providing part of the answer, and perhaps pointing the way to further progress in the future, is the World Bank. Loans from the World Bank are arranged usually for countries which are attempting to develop their economies through expanded industrial production. More often than not they are for the development of electric power projects or transportation facilities. Although we consider the mineral industries to be basic factors in industrial development and very important factors in the early stages of development of a country, few of these loans are for mineral development-no more than a half dozen out of a total of well over 300 loans which have been granted to date. Yet the World Bank has played a far more important part in world mineral development than these figures would indicate. The few loans for mineral development which it has made are important, but of considerably greater importance are the secondary effects of many of the non-mineral development loans and some of the special services which the Bank also offers.

Jan 5, 1963

By Frederick H. McDowell

Notwithstanding the rapidly increasing use of copper, due to the extension of its applications within the last few years, the fact of its continued steady decline in price stands prominently forward. Nor have we far to look for the cause. The opening up of the vast copper-deposits of our Western States and territories is the metallurgical event of the last five years. We must not forget, in looking at the new field, the changed conditions under which the metallurgist must work, as compared with the previous history of copper-smelting. Until quite recently, the copper-plants of the country were few in number; and the concentration of industry implied in this circumstance, allowed many practices which must be considered as inapplicable to the conditions offered at the many mines which have of late become such important factors in our copper-production. Thus the old style of smelting the ore for matte in brick furnaces, involving great expense and time in their construction, while deservedly losing repute even in its old strongholds, in comparison with water-jacketed smelters, is still in some cases adhered to. But to put up such furnaces at Western mines would be out of the question. The large and continual need of brick for relining and repairs acts as an effectual bar, when such furnaces come into competition with the light, portable, and easily managed water-jacketed smelters of improved types. It is owing to the present unusual activity, manifested in the opening up of new copper-properties and the erection of plants for working them, that any improvement in furnace-construction is of especial interest and importance. The method in which processes are copied without variation in the rapid growth of metallurgical interests, has already been strikingly exemplified in the history of

Jan 1, 1885

By F. V. Lene, E. J. Westerman

The recrystallization behaviors of two extruded and cold-drawn experimental sintered aluminum powder alloys, containing 1.75 and 3.0 pct Al2O3 by weight, were compared with that of extruded and cold-drawn commercially pure alumirzum. The kinetics of recrystallization of the alloys are described semiquantitatively. For the alloy containing 1.75 pct A l203 the rates of nucleation and of growth were also semiquantitatively determined. THE most striking property of aluminum alloys strengthened by a dispersion of Al2O3, the so-called SAP alloys, is their stability at elevated temperatures. One of the manifestations of this stability is their resistance to recrystallization after they have been cold worked. Most of the commercial grades of either the Swiss SAP or of Alcoa's Aluminum Powder Metallurgy Products have not been recrys-tallized after cold working, even when they are heated for a long time at a temperature near the aluminum melting point. Lenel, however, observed that the dispersion strengthened aluminum alloys with a larger spacing between the oxide particles than that of most commercial grades would recrys-tallize.1 It appeared to be of interest to further investigate the mode and kinetics of recrystallization of these alloys, and to compare their recrystallization behavior with that of commercially pure aluminum. Because homogeneous deformation of these SAP alloys in tension did not provide sufficient cold work to induce recrystallization, they were cold worked by wire drawing; the nonuniformity of this deformation unavoidably complicated the interpretation of the recrystallization studies. EXPERIMENTAL DETAILS Extrusions—Two types of sintered aluminum powder extrusions were used in this study. One type, designated AT-400, was produced from Reynolds atomized aluminum powder consisting of spherical particles averaging 3µ in diam and containing 1.75 wt pct of Al2O3. This powder was very similar to the R3M powder from which extrusions were previously prepared with an average spacing of 0.9µ between oxide particles.2 The second type, designated MD 2100, was produced from Metals Disintegrating Co. flake powder containing 3.0 wt pct of Al2O3, with an average flake thickness of 0.8µ. The average spacing between oxide platelets in MD 2100 extru- sions was 0.45µ.2 Powder compacts of 3/4-in. diam were extruded at 1000°F into 0.097-in. diam (AT-400) and 0.093-in. diam (MD 2100) wires by methods previously described.3 In order to compare the recrystallization behavior of sintered aluminum powder extrusions with that of wrought commercially pure aluminum 3/4 in. rod stock of 1100 F aluminum was extruded at 1000°F into 0.102-in. diam wire. Wire Drawing—Tungsten carbide dies were used for the AT-400 and 1100 F alloys. They had an included angle of about 15 deg and reduced the wire area approximately 7 pct per pass. Steel dies with an included angle of 11 to 13 deg and an average reduction per pass of 10 pct were used for drawing the MD 2100 alloy, because drawing this alloy through the carbide dies produced overdrawing defects. Heat Treatment—The cold-drawn wires were cut into small samples, and the deformed ends were etched off. The samples were each wrapped tightly in a single layer of aluminum foil, and individually isothermally annealed in a lead bath. Metallography—The modes and kinetics of recrystallization were determined by metallography. Mounted and polished specimens were anodized in a solution of 1.8 pct HBF4;4 examination under polarized light clearly revealed their grain structures. The recrystallized grains were generally much larger than those of the unrecrystallized matrix, and could clearly be distinguished because they alternated between maximum and minimum light reflection when the microscope stage was rotated, while the unrecrystallized matrix had a comparatively homogeneous "salt and pepper" structure. The fractional recrystallized volumes of the dispersion hardened alloy wires were determined by cutting and weighing of recrystallized and total transverse areas on photomicrographs. The recrystallized grains in the 1100 F alloy were too small to be cut out individually; therefore a combination of cutting and lineal analysis was used in this case. RESULTS AND DISCUSSION Modes of Recrystallization—The modes of recrystallization of the three alloys varied widely. In the 1100 F alloy nucleation and growth started in the region midway between the center and the surface;

Jan 1, 1961

By Jan D. Miller

Under the name given to this column, I almost feel obliged to write about some aspect of grinding, but I have decided instead to comment on the future of chemical processing. In recent years, I have seen a tremendous interest in extractive metallurgy develop among undergraduate and graduate students at the University of Utah. For example, of the 12 graduating seniors this year, over half seem to prefer extractive metallurgy to physical metallurgy. In particular, they seem to be most interested in hydrometallurgy, or chemical processing, obtaining industrial exposure to the phenomena they study via part-time employment at the Kennecott Research Center and the USBM Metallurgical Center in Salt Lake City. The stimulus has been generated by society itself. Many students are dedicated to the proposition that new technology can circumvent the destruction of our environment, a concept which provides considerable motivation. At the governmental level, the recent concern for the quality of our environment has created action in the area of chemical processing both through imposition of stringent air and water quality standards, and through increased funding for technological research in this area. The National Academy of Sciences (NAS) gave impetus to this movement when it pointed up the need for development and support of such disciplines as extractive metallurgy, particularly chemical processing, in a recent report on Mineral Science and Technology. The recommendations in the NAS report have prompted governmental action on many fronts, including the Bureau of Mines, and have also given rise to direct legislation in the form of two bills -H. R. 3492 and S. 635- presently before Congress to a mineral engineering education. The report recommends that chemical processing technology (more generally extractive metallurgy) be developed by both new engineering techniques and unconventional chemical techniques such as application of the chemistry of nonaqueous liquids to mineral systems.

Jan 1, 1971