Search Documents

By Michael Tenebaum

IN a previous investigation1 the authors studied the effect of pressure on the reduction of iron ores by hydrogen. With hydrogen as a reducing agent, the rate of reduction was increased substantially by increasing the pressure from 1 to 2 atmospheres. The results with hydrogen prompted the present study of the effect of pressure on reduction with carbon monox-ide and with mixtures of carbon monoxide and nitrogen. FEATURES OF REDUCTION PROCESS The gas stream in the lower part of the blast furnace always contains sufficient concentrations of reducing gases to complete reduction provided sufficient time is allowed for the reaction to proceed. Reducing gases react immediately with the iron oxide on the surface of lumps of ore. However, as the unreduced surface recedes from the easily accessible exterior of the lump, the reaction proceeds by virtue of the diffusion of the gases into and out of individual pieces. The rate of diffusion of gases, which undoubtedly plays an important role in the reduction of iron ores, depends on several factors, most impor-tant of which are: (1) molecular weight or density, (2) pressure, (3) tem-perature, (4) concentration gradient. Thus, the rate of reduction of a lump of iron ore at any temperature will depend not only on the specific reaction rate but also upon: (1) available surface of unreduced iron oxide, (2) rate of diffusion of the reducing gas to the reacting surface, (3) rate of effusion of the gaseous products of the reaction from the reacting surface, (4) adsorption of the gases on the reacting surface.

Jan 1, 1939

By J. W. Moody

The first Rodpeb mill ever built and placed in full scale successful operation went onstream in mid- 1960 at Marquette Cement Manufacturing Co.'s newly modernized portland cement production plant at Nashville, Tenn. It replaced a third stage of fine crushing and two 7x22-ft Compeb mills in the wet raw slurry grinding department. The Rodpeb mill at Nashville is similar in appearance to a Compeb mill but is larger. The mill, which operates in open circuit, is 9 ft in diameter and 38 ft long. The rod compartment is 12 ft long, with the rods being 11.5 ft in length and ranging in diameter from 4 in. down to about 1 in. The weight of the rod charge is 100,000 lb. The liners of the rod compartment are of the Lorain design.

Jan 4, 1963

By A. Kenneth Schellinger

DURING the comminution of a brittle material in the presence of dry air, no known phase change or chemical reaction takes place. The energy changes associated with the comminution are those of the transformation of kinetic energy into heat energy and the energy absorption represented by the actual rupture of molecular and/or ionic bonds. The random nature of the actual grinding process in a tumbling-mill often precludes the effective application of a rupture force on each individual particle of brittle mineral present. The result must be a great deal of useless vibration on an atomic scale in both the brittle mineral and the grinding medium below the elastic limit, which vibration is eventually manifested as heat energy in the mill. The actual rupture of molecular, or ionic, bonds creates new surface on the brittle minerals; each square centimeter of this new surface then must possess a number of potential bonds, each of which could reform theoretically with the release of energy. The sum total of this potential energy of bonding per unit of new surface, minus bond satiation effects of the enclosing gas or liquid, must be the surface energy of the mineral. If the comminution of the brittle mineral were carried out within the chamber of a calorimeter, the energy released as heat could be determined rather accurately. Moreover, the total kinetic energy input to the comminuting mass (mineral and medium) conceivably could be derived by a suitable torquemeter and revolution counter if the whole calorimeter were revolved. The difference between these two energy figures should then represent the net energy (gross energy input-heat energy output) used in creating

Jan 6, 1951

By Clifford C. Hanninen, Allan H. Caverson

Within the past nine years a means for measuring the distance between mine roof and floor was developed at the White Pine mine which yields relevant information utilized in the mining operation. The technique known as "convergence" is an efficient, low cost way for obtaining large quantities of data for predicting roof falls, caving activity and overall mine stability. Since 1964 the activity of convergence measurements has expanded to become a production tool found in all sections of the mine. The program involves four types of activity: 1) monthly measurements in areas known to be active and in sample blocks scattered throughout the mine for a long-term stability study; 2) semi- monthly measurements along vital travel roads, belt drifts and compressor sites; 3) weekly measurements in areas where men are working; 4) daily measurements in pillar-recovery and caving operations.

Jan 5, 1973

By W. L. Dennen, V. H. Wilson

THIS paper is a description of the opera¬tion and results of a Humphreys Spiral Silt Cleaning Plant at the Powderly Colliery of The Hudson Coal Co. during the first nine months of operation and follows a pre¬liminary description given at the Anthracite Institute in May, 1947, in a paper titled "Preparation of Anthracite Sift for Boiler Fuel in a Humphreys Spiral Test Plant" by H. H. Otto, V. H. Wilson and W. L. Dennen. This plant is considered a full size operating test plant and, like all new plants, numerous minor changes in the methods of operation have been made from time to time to secure the results desired. Views of the silt preparation plant and of the screening house are given in Fig 1 and 2. This plant consists of 48 spirals in 8 batteries of 6 spirals each, 36 of which were to be operated as primary spirals and the remaining 12 as secondary spirals. A brief description of the plant and its operation follows. The only material cleaned at the plant during 1947 was that carried in the underflow from the Thickener which handles the Breaker waste water. This underflow, amounting to approximately 2000 gpm of water and containing 12.6 pct of solids, is pumped .to vibrating screens where the plus 316-in. material is removed. (Fig 3). This oversize material drops into a pocket from which it is trucked to the run-of-mine

Jan 1, 1948

Those familiar with the war in France at first hand know that in these last two years the weight of the suffering has fallen upon the families of the well-to-do classes; those who before the war lived in comparative ease and comfort, with every prospect of educating their children as their parents and grandparents had been. Thousands of the men in these families have been killed, "officiers d'élite," and the small pensions accorded the widows permit them only to house and feed their children HELÈNE JOURNÈS. and give them a common-school education. The pension for a lieutenant's widow is $245 a year; for 'a captain's, $345; for a colonel's $575; and so on. At present, it requires three francs a day to provide food for one person in cities, and conditions are not improving. The American Ouvroir Funds, 681 Fifth Ave., New York City, has tried for nearly two years to have individual Americans give individual children a "bourse," or purse, as it is called, of from $150 to $250 a year, so that they may enter such educational institutions as the Lycées, the Polytechnique, Beaux Arts, St. Cyr, etc. The war relief societies of these military schools furnish photographs and histories of children under their care and on their lists.

Jan 12, 1918

By C. T. Bischoff

This paper describes the results of testing with colorimetric methods, using "dithizone", soil samples taken over various known copper and zinc deposits covered by glacial till. Variation in results is shown for different depths and types of overburden as well as grade and type of deposit. Limiting factors for the practical application of this work are discussed. The method has proved successful for copper and zinc deposits under clay and fine sand with depths up to at least 30 ft but fails in coarse sand and gravel unless depths are very shallow. Swamps require penetration to the underlying subsoil for sample material. DURING the past few years geochemical testing for traces of heavy metals in water, soil, rock, and vegetation has aroused increasing interest. Various techniques for field and laboratory determinations have been described in the literature, as have some of the results of application. However, little information has been published regarding application to glacial terrain. Over 90 pct of the Canadian Shield is overburdened, resulting in high costs for mineral exploration once the outcropping ore deposits have been found. This has been largely responsible for the widespread application of mining geophysics in Canada, permitting concentration of effort on area or zones considered most favorable. However, geophysical interpretation has its limitations, since at least 90 pct of the structures indicated thereby contain no valuable minerals. A more direct approach is therefore highly desirable. If underlying base metal mineralization can be detected by sampling soil or vegetation at moderate cost this should prove of great help in locating new discoveries or extending known ones. A large proportion of Canadian ore deposits contain appreciable copper or zinc, even where these are not the principal economic metals. Consequently the field of application is a broad one. This paper deals with investigations along these lines with particular emphasis on soil sampling. The problems involved from the start were: 1—Which types of glacial soil, if any, would best lend themselves to testing, and conversely which types might be considered relatively hopeless? 2—Through what depths of overburden could significant mineralization be detected? 3—What sampling techniques would prove economically applicable? This included minimum depth of sample and maximum spacing that could be allowed.

Jan 1, 1955

By G. D. Oxx, L. F. Coffin

The concept of using a phase that is liquid at service temperatures as a component of coatings for refractory metals has been described. The liquid, an alloy of gold and silicon, is retained on a molybdemum surface by a capillary system made of molybdenum disilicide. The coating has the advantage of good thermal shock and has a self-henling chracteristic. In order for highly stressed structures to exceed a service temperature of 2000°F, it has become apparent that a development that does not depend on the traditional iron, cobalt, or nickel-base alloy is needed. Alloys of the refractory metals, i.e., molybdenum, tungsten, tantalum. niobium (colum-bium), and rhenium are potentially useful at extremely high temperatures that more conventional alloys would never be expected to achieve. A new alloy of molybdenum has become available that has a 100-hr rupture strength of 35,000 psi at 2200°F.1 As a result of this work, it may be assumed that a material with adequate mechanical properties at 2200?F is now available. Unfortunately, this alloy and all other known alloys of the refractory metals suffer from not being; serviceable in an oxidizing atmosphere for a very long time. In order to permit general use of refractory metals at high temperatures, it is necessary to prevent destructive oxidation by appropriate alloying or by protective coatings. The liquid phase coating reported here is representative of a concept for the protection of metals that permits higher service temperatures and introduces a new group of materials for selection as coatings. Coating Requirements—Service conditions that represent potential applications for refractory metals vary considerably: however, it is possible to consider two conditions that are usually present. The refractory metal1 component must be heated to the service temperature at least once and usually frequently. When a solid coating is used, usually the coating and basis metal do not have the same coefficient of expansion. This difference causes thermal stress in the coating that is aggravated by rapid heating and cooling and eventually causes coating failure. The second consideration is the probability that there will be damage to the coating by some environmental condition. In jet engines, for example, it is expected that large particles, stones, metal parts, and so forth, will strike a bucket at high speed and cut a hole in the coating. In addition to the above considerations, the coating must also have other fundamental properties. Obviously, it must be oxidation resistant. In addi- tion, it must prevent permeation of oxygen and subsequent oxidation of the basis metal at the interface. Also, diffusion of the basis metal to the outside surface and subsequent oxidation there must be prevented. Finally, the coating must not react with the basis metal to form a weak bond at the interface. It should be noted that the coating need not support a load: it must only remain intact. Liquid Phase Coating Design Factors—In the use of a liquid as a principal coating constituent, it would be expected that the two service conditions mentioned above would be satisfied. A liquid would flow under the influence of the thermal strain developed by coating-basis metal expansion mismatch such that failure from this source would not be expected to occur. It is also probable that the ability of a liquid to flow would provide a self-healing effect. Thus, damage caused by particles in the atmosphere would be repaired. A third advantage is evident in that vapor pressure rather than melting point limits the service temperature. This latter advantage permits use of low melting but oxidation resistant metals such as gold or copper that would be quite useless if the solid state was required. A low viscosity liquid alone. however, is a totally unsuitable coating because it will simply flow off a component, particularly under the influence of a high acceleration field. A method of preventing liquid loss must be devised. In this case, it is desired that the liquid have a low viscosity so that it may easily flow into flaws; thus, raising the viscosity is not a satisfactory solution. One other inherent difficulty is caused by the high mobility of atoms in the liquid state as compared to the solid state. Because of this mobility, it would be expected that gases would diffuse more rapidly through a liquid. It is also probable that the solubility of oxygen in the liquid would be comparatively high. These factors would tend toward rapid permeation of oxygen and oxidation of the substrate. It is most reasonable that this problem could be solved by incorporating a solid phase, which is impermeable to gases, as a component of the coating. To overcome the tendency of a liquid to flow easily, it is possible to use surface tension to advantage. If the surface were made up of a large number of capillary tubes of sufficiently small diameter, then surface tension would hold the liquid even against the acceleration of a centrifugal field.

Jan 1, 1961

By Jerome Strauss, Carl L. Shapiro

THIS is a critical examination of the theory that the amount of carbon necessary to form the iron-carbon (carbide) eutectoid is lowered by the addition of any carbide-forming element. Although this theory has been built up over a long period of years,, it appears, in the light of recent published investigations upon the ternary constitutional diagrams of iron with carbon and other alloying elements, to be no longer tenable. A survey of these new results, summarized below, shows that (as is known) some metals lower the carbon content of the iron-carbon (carbide) eutectoid, whereas others raise it, but (as not heretofore clearly set forth) some first move the eutectoid in one direction and then, at higher concentrations, shift it in the opposite direction. Moreover, these differences in behavior exist even among the common alloying metals classed as carbide formers. PART I INFLUENCE OF BODY-CENTERED CUBIC ELEMENTS The effects of the various body-centered cubic metals (chromium, tungsten, molybdenum, vanadium, columbium and tantalum) are reviewed individually. Iron-carbon-chromium System.-In the monograph on Alloys of Iron and Chromium, Kinzel and Crafts' concluded that the carbon content of the eutectoid is lowered by increasing the chromium content. The quantitative influence of chromium on the eutectoid point of iron-carbon alloys was shown by Monypenny2 (Fig. I) and no data have been forthcoming to refute his findings. Iron-carbon-tungsten System.-Gregg,3 in the monograph on Alloys of Iron and Tungsten, accepted the data showing that tungsten decreases the amount of carbon required to form the eutectoid. The influence of tungsten on the eutectoid percentage of carbon as determined by Oberhoffer and Daeves4 is shown in Fig. a; these results have received general approval. Iron-carbon-molybdenum System.-In the monograph on Alloys of Iron and Molybdenum, Gregg5 reviewed the work of Guillet,6 Swinden,7 and Reed,8 all showing that molybdenum lowered the carbon content of the eutectoid, whereas Takei9 contradicted this conclusion. Svetchnikoff and Alferova,10 a little later, showed that large additions of molybdenum shift the eutectoid to the right. These last-named investigators found that molybdenum, up to 1.2 per cent, shifts the pearlite point and the point of maximum solubility of cementite in the gamma phase only slightly in the direction of lower carbon content; on the other hand, increasing amounts of molyb-

Jan 1, 1943

By K. C. Ko, M. K. McCarter

Experimentation with seismic velocity measurements at Kennecott Copper Corp.'s Bingham mine disclosed that some recognized slide areas are characterized by low velocity profiles. A new traverse technique employed during the investigation allows rapid and precise measurements of a quantity referred to as "apparent velocity." This value is a weighted average of the actual velocity in the overbreak zone near the surface and in the intact rock at depth. The low points on the velocity profile are apparently the result of lower actual velocities and deeper overbreak in less competent material within the slide zones. Experience verifies the usefulness and practicality of the technique in delineating adverse areas prior to detectable failure. The technique may be employed as a rapid and economic means of slope stability surveillance in large open pit mines.

Jan 1, 1973

By I. E. Rosenzweig

THE problem considered in this paper is as follows: An arbitrary horizontally stratified area is given. The electrical properties of this area are characterized by a function p(z) (Fig. 1), which shows the relationship between resistivity p of thes oil and the depth z. For such general case the apparent resistivity p* will be computed, by FIG. 1.-GRAPH OF FUNCTION p(z) FIG. 2.-GRAPH OF p(Z) FOR n HOMO-GENEOUS LAYERS. earth-resistivity measurements carried out by any given configuration of electrodes. General solutions of this problem appear to be very important for interpretation of field results of resistivity measurements, concerning structural investigations. Such solutions have been given by many authors for the special case of a finite number of homogeneous layers (Fig. 2)1-4 as well as for the more general case of continuously rang-ing resistivities. 5-8

Jan 1, 1939

By R. W. Raymond

This paper is simply a summary, prepared at the request of the Council of the Institute, of the report of Mr. Albert Ladd Colby, of South Bethlehem, Pa., presented at the New York meeting (October, 1896) of the Association of American SteelManufacturers, on " The Advisability of the Endorsement by the Association of the United States Standard Gauge, approved by Act of Congress, March 3, 1893, to the Exclusion of the Birmingham Gauge, the .Brown and Sharpe, and all Others:" a subject on which, at the Pittsburgh meeting (April, 1896) of the said Association, Mr. Colby had been appointed as a committee. The report favors the adoption, not of the United States standard gauge to the exclusion of others, but of a decimal system of gauging all materials in thousandths of an inch, thus doing away entirely with arbitrary gauge-numbers running in inverse order to the actual thickness. The American Institute of Mining Engineers originated this movement. The report of its committee on a standard wiregauge, presented in October, 1877,* recommended the abandonment of the system of fixed gauges for commercial use, and of the system of representing the diameters and sizes by numbers, and the adoption, in lieu thereof, of the system of expressing sizes in thousandths of an inch or fractions of a millimeter, and the use of the micrometer-gauge as a means of measuring sizes. In 1892 the American Society of Mechanical Engineers appointed a similar committee, and corresponding action was

Jan 1, 1898

By Theodore Hatch

The pneumatic rock drill operates essentially as a crusher. The rock is shattered into a powder that is removed from the drill hole by the air stream introduced through the hollow drill steel. Particles thus produced vary in size from 1/4 in. or larger down to diameters too small to be revealed by the ordinary microscope. The power consumed by the drill is proportional to the new surface area of the powdered material, therefore the greater the proportion of "dost" produced, the higher the power consumption and the lower the drilling speed. A considerable amount of material ejected from the hole settles on the rock and much of this falls back as the mound builds up to be crushed further before it is removed again. The cushion of dust at the bottom of the hole reduces the effectiveness of the blow of the bit and thus lowers the rate of drilling. The unfavorable working conditions created by the dust also reduce the drilling speed by lowering the efficiency of the operator. Thus, the dust produced by rock drills constitutes a serious drawback to economical performance on all drilling operations. To the economic objections, one must add the more important objection to the health hazard created when the dust contains free silica (quartz). The silicosis problem is a familiar one in many mines, tunnels, and other underground operations as well as in quarries and other types of open rock excavation. Dust is a necessary end product of all pneumatic drilling operations. Its production cannot be eliminated although the proportion of microscopic particles can be reduced by using improved drill steel, proper methods of sharpening, more efficient drills, etc.—improvements that increase the drilling speed largely by increasing the size of the cuttings. The absolute improvement secured in this way is not great, however, and the pneumatic drill must always remain a dust-producing machine. Definite benefits do result, on the other hand, from the use of dust-control equipment that captures the dust as it emerges from the hole and conveys it to a remote point of discharge. Dust production continues, but dust dispersion into the atmosphere is prevented. The dust is removed as rapidly as it is formed, with the following results: (I) The silicosis

Jan 1, 1937

By H. S. Coe

ENGINEERS have long recognized the desirability of correlating the data obtained from small-scale slime-settling tests with commercial work as carried on in large tanks. This need, though most apparent in designing new installations, frequently arises also in existent plants, since a large range of experimental work can be performed without interfering with regular operation. GENERAL SETTLING PHENOMENA In order to develop rational methods of laboratory testing, it becomes necessary to study the general phenomena of settling. Since it was desired to give the public the benefit of these methods at as early a date as possible, together with the knowledge of the general principles of slime settling necessary for a clear understanding of the laboratory tests, we have ventured to discuss the subject in so far as brought out by the work which we now have under way. We realize that certain of our preliminary conclusions may be subject to modification, but it seems probable that, with but few exceptions, the general laws enunciated will cover the settling behavior of all pulps encountered in metallurgical plants. However, it must be recognized that there is still a vast amount of work to be done upon certain phases of the subject; therefore, at this time we will attempt only a discussion of the behavior of ore pulps during the process of settling or dewatering, under certain given conditions. The laws and principles controlling these conditions are not fully established, so that a complete discussion of them will not be attempted in this paper. In metallurgical practice, slime pulp consists of water, finely divided sand

Jan 3, 1916

By Carl L. Shapiro, Jerome and Strauss

This is a critical examination of the theory that the amount of carbon necessary to form the iron-carbon (carbide) eutectoid is lowered by the addition of any carbide-forming element. Although this theory has been built up over a long period of years, it appears, in the light of recent published investigations upon the ternary constitutional diagrams of iron with carbon and other alloying elements, to be no longer tenable. A survey of these new results, summarized below, shows that (as is known) some metals lower the carbon content of the iron-carbon (carbide) eutectoid, whereas others raise it, but (as not heretofore clearly set forth) some first move the eutectoid in one direction and then, at higher concentrations, shift it in the opposite direction. Moreover, these differences in behavior exist even among the common alloying metals classed as carbide formers. PART I Influence of Body-centered Cubic Elements The effects of the various body-centered cubic metals (chromium, tungsten, molybdenum, vanadium, columbium and tan. talum) are reviewed individually. Iron-carbon-chromium System.—In the monograph on Alloys of Iron and Chromium, Kinzel and Crafts1 concluded that the carbon content of the eutectoid is lowered by increasing the chromium content. The quantitative influence of chromium on the eutectoid point of iron-carbon alloys was shown by Monypenny2 (Fig. I) and no data have been forthcoming to refute his findings. Iron-carbon-tungsten System.—Gregg,3 in the monograph on Alloys of Iron and Tungsten, accepted the data showing that tungsten decreases the amount of carbon required to form the eutectoid. The influence of tungsten on the eutectoid percentage of carbon as determined by Oberhoffer and Daeves4 is shown in Fig. 2; these results have received general approval. , I ron-carbon-molybdenum System.—In the monograph on Alloys of Iron and Molybdenum, Gregg5 reviewed the work of Guillet,6 Swinden,7 and ReedI8 all showing that molybdenum lowered the carbon content of the eutectoid, whereas Takei9 contradicted this conclusion. Svetchnikoff and Alferova,10 a little later, showed that large additions of molybdenum shift the eutectoid to the right. These last-named investigators found that molybdenum, up to 1.2 per cent, shifts the pearlite point and the point of maximum solubility of cementite in the gamma phase only slightly in the direction of lower carbon content; on the other hand, increasing amounts of molyb-S

Jan 1, 1944

By Jerome and Strauss, Carl L. Shapiro

This is a critical examination of the theory that the amount of carbon necessary to form the iron-carbon (carbide) eutectoid is lowered by the addition of any carbide-forming element. Although this theory has been built up over a long period of years, it appears, in the light of recent published investigations upon the ternary constitutional diagrams of iron with carbon and other alloying elements, to be no longer tenable. A survey of these new results, summarized below, shows that (as is known) some metals lower the carbon content of the iron-carbon (carbide) eutectoid, whereas others raise it, but (as not heretofore clearly set forth) some first move the eutectoid in one direction and then, at higher concentrations, shift it in the opposite direction. Moreover, these differences in behavior exist even among the common alloying metals classed as carbide formers. PART I Influence of Body-centered Cubic Elements The effects of the various body-centered cubic metals (chromium, tungsten, molybdenum, vanadium, columbium and tan. talum) are reviewed individually. Iron-carbon-chromium System.—In the monograph on Alloys of Iron and Chromium, Kinzel and Crafts1 concluded that the carbon content of the eutectoid is lowered by increasing the chromium content. The quantitative influence of chromium on the eutectoid point of iron-carbon alloys was shown by Monypenny2 (Fig. I) and no data have been forthcoming to refute his findings. Iron-carbon-tungsten System.—Gregg,3 in the monograph on Alloys of Iron and Tungsten, accepted the data showing that tungsten decreases the amount of carbon required to form the eutectoid. The influence of tungsten on the eutectoid percentage of carbon as determined by Oberhoffer and Daeves4 is shown in Fig. 2; these results have received general approval. , I ron-carbon-molybdenum System.—In the monograph on Alloys of Iron and Molybdenum, Gregg5 reviewed the work of Guillet,6 Swinden,7 and ReedI8 all showing that molybdenum lowered the carbon content of the eutectoid, whereas Takei9 contradicted this conclusion. Svetchnikoff and Alferova,10 a little later, showed that large additions of molybdenum shift the eutectoid to the right. These last-named investigators found that molybdenum, up to 1.2 per cent, shifts the pearlite point and the point of maximum solubility of cementite in the gamma phase only slightly in the direction of lower carbon content; on the other hand, increasing amounts of molyb-S

Jan 1, 1944

By Charles M. Bayer

Reading in the AIME annual reports that certain activities have been financed by the Rocky Mountain Club Fund, less senior members of the Institute may wonder. "What's the Rocky Mountain Club?" Less youthful members will not have to wonder. They will recall the Club as an intriguing, almost fantastic organization, largely of western mining men, that flared across the New York horizon, flamed brilliantly for a little more than two decades, then sputtered out of existence- glorious even in its last flash. It was the only product of its mold, a fabulous group of magnanimous men who unhesitatingly sacrificed a cherished dream for which they had raised millions of dollars so that the money, instead of creating a magnificent club house, could be used instead to save the lives of starving Belgian children in World War I.

Jan 12, 1964

By Leonard R. Weisberg

The general properties of diffusion in GaAs are reviewed. A total of .fourteen atoms have been studied to date, and activation energies for eleven reported are (in ev): Ga (5.6), As (lo), Zn (2.49), Cd (2.43), Sn (2.5). Mn (2.75). S (4.0). Se (4.2). Ag (0.33), Cu (0.52). and Li (1.0). The dijfusion of the first eight atoms, as measured by Goldstein using radiotracer techniques, established the principle of sub lattice diffusion for both host and impurity atoms, since atoms substituting for gallium have lower activation energies than those substituting for arsenic. The diffusion constant of interstitial copper has been determined for the first time by Hall and Racette using heavily doped p-type samples in which interstitial copper predominates. The anomalous behavior of zinc, which has an abrupt diffusion front and a strong dependence on zinc concentration, has recently been quantitatively explained in terms of an interstitial-substi-tutional equilibrium-diffusion mechanism. Lithium and silver diffuse mainly interstitially, while the diffusion of phosphorus is complicated by the continual formation ofGap. Junction-migration measurements indicate diiferent results than radiotracer techniques, and this is one problem that still remains, together with discrepancies in cadmium-diffusion results, and an unexplained dependence of impurity diffusion on arsenic pressure. BESIDES the usual insights into the behavior of atoms in solids, studies of diffusion in semiconductors have additional importance for device applications. In fact, the amount of diffusion studies performed on a semiconductor might serve as a simple barometer of its technological importance. Thus, the information accumulated for GaAs is not yet quite comparable to that for germanium or silicon, but considerable knowledge is available. The diffusion of at least fourteen atoms has been investigated for GaAs, and the diffusion constants have been determined for eleven of these. Interesting results were found for GaAs that elucidated problems not previously solved for germanium or silicon. For example, the interstitial-diffusion constant for the very fast diffusant, copper, was first measured in GaAs. Also, solutions for interstitial-substitu-tional equilibrium diffusion in extrinsic material were provided first for GaAs, although they are ap- plicable to germanium, silicon, and other semiconductors. Studies in GaAs firmly established the concept of sublattice diffusion, which should have application in many different compound systems. The purpose of this paper is to review briefly the general state of knowledge concerning diffusion in GaAs. First some general aspects of diffusion will be covered, and next attention will be given to the results mentioned above. Diffusion in GaAs has been measured both by radiotracer and junction-penetration techniques, and some discussion will be given of differences in the two sets of results. The comprehensive work of oldsteinl-' has served as the primary reference for the diffusion of well-behaved substitutional atoms in GaAs. Since a review has recently been presented of many of these reults, details of the diffusion data will not be repeated. Neither will any discussion be given of the experimental techniques of diffusion measurements, except to note here, in passing, the simplicity and effectiveness of the precision lapping device employed by Goldstein.' I) EXPERIMENTAL RESULTS AND DISCUSSION A) Summary of Experimental Results. Diffusion constants D = Do exp(E/kT) have been determined for eleven atoms in GaAs: a,' AS,' n,'" Cd,'" n,' n,8 s, e,' Ag,O CU," and i." These results are summarized in Table I. In addition, diffusion was investigated for phosphorus,4'12 germanium,I3 and ilicon,' but Do and E were not determined. Radiotracer techniques were used for most of the studies except for lithium, where a combination of chemical and electrical techniques was employed, and germanium and silicon, where junction-migration techniques were applied. The diffusion of zinc, manganese, sulfur, and tin was also measured using junction migration.13'14 Goldstein demon-

Jan 1, 1964

By R. B. Russell

The expansion coefficients of hexagonal (a) zirconium have been calculated from the lattice expansionparameters of both coefficientsofhexagonallow and high hafnium alloys in the range 0° to 600°C. It is found parametersofboththat the coefficients are straight-line functions of the temperature and that the effect of hafnium is to depress the mean coefficients by about 1 pct at room thattemperature and 9 pct at 600°C. The cubic (ß) form was stabilized so that its coefficient could be determined from 400' to 900°C. COEFFICIENTS of thermal expansion for hexagonal-close-packed (a) zirconium were determined up to 600°C (1112°F), without any interference from the effects of preferred orientation, by measurement of the lattice parameters obtained from a symmetrical back-reflection focusing X-ray camera. This paper combines the results for a 1.2 atomic pct hafnium alloy from an earlier report' with those for hafnium-free zirconium. The problem confronting the investigator is essentially that of getting sharp, high-angle diffraction lines which represent the material at a known constanl. temperature and chemical composition. In order to do this, it was necessary to use the proper X-ray emission wave length (Co K was chosen) and to have a fine-grained metal whose atomic spacings would be free from effects of cold work (the specimen was annealed) and to prevent a changing composition owing to gas absorption during the heating of the metal to temperature (the sample was heated in a vacuum). A summary of the effect of temperature on properties is listed in Table I which gives data for ordinary zirconium, as well as new values for the low hafnium metal. The coefficients of the linear thermal expansion that have been reported are given in Table 11. The discrepancies shown may be explained perhaps by the effect of preferred orientation, and McGeary and Lustman2 have done this successfully for sheet metal. The differences in texture cannot explain all the differences in expansion coefficient shown in Table II. liesults by the author agree most closely with those of Kroll.3 Chemical analysis of the high hafnium metal pre- viously reported1 showed that it was 98.22 atomic pct (97.40 wt pct) pure. The low hafnium metal was dehydrogenated Westinghouse crystal bar, designated SMZ-137A. Its analysis was as given in Table 111 (chemical analyses 5377, 5431, and 5432).

Jan 1, 1955

By L. S. Austin

I. Introduction............ 431 II. Organization............ 432 III. Production............ 434 IV. Transportation............ 435 V. Sampling..........436 VI. Concentration............ 440 VII. Blast-Furnace Plant........... 442 1. Construction........... 442 2. Operation............ 450 VIII. Advantages of Large Furnaces........ 455 1. Saving in Fuel........... 455 2. Saving in Jacket.Water..... 455 3. Quick and Large Discharge of Matte and Slag... 455 4. Decrease of Incrustation... 456 5. Elasticity of Operation..457 6. Large Flow Through Fore.Hearths...4. 57 7. Alterations Without Interruption..458 8. Variations in the Composition of Slag....458 9. Less Labor-Cost.......... 458 10. Less Initial Cost.......... 460 IX. Briquetting.Plant........... 460 X. Roasting-Plant............ 462 1. Kilns............ 462 2. Reverberatory Furnaces...468 XI. Converter-Plant........... 474 1. Construction ..........474 2. Operation.......... 476 XII. Flues and Stacks........... 478 XIII. Arsenic-Plant............ 480 XIV. Coke-Washing Plant.... 452 XV. Slime.Ponds ........... 483 XVI. Brick-Plant............ 484 I. Introduction. The Washoe plant; in Anaconda. Mont., together with the local street-railroad, ranches. a foundry and machine-shop. A

Jan 1, 1907