Search Documents

By Victor O. Homerberg, Dexter N. Shaw

A study of the correlation of the mechanical properties and of the microstructure with the heat treatment of 60-40 brass has been confined, heretofore, to the rolled or extruded material as received from the mannfacturer. The results obtained by Babson and Buhler,' Bengough and Hudson12 Stead and Stedman,3 and Brayton4 have been confined to the treatment of the material as received. No attempt was made to get the material into a given condition and then to work from this basis. To start with a given structure would have the decided advantage of making the work independent of the original condition, hence, to make the results reproduceable. In a previous paper, it was shown, in connection with the study of the transformation that occurs at about 470" C., that if specimens were quenched to produce the beta structure and then reheated, the beta would begin to break down, at approximately 200" C., into a very finely divided alpha. It was predicted that important results might be obtained if test pieces were to be given a similar double heat treatment and then tested for the mechanical properties as well as a study of the microstructure. The material used in the present investigation was a 3/4-in. round bar of extruded muntz metal of the following composition: Copper, 61.05 per cent.; zinc (by difference), 38.90 per cent.; lead, 0.05 per cent.; iron, trace; tin, nil.

Jan 1, 1924

By J. D. Hanawalt, W. H. Gross

Magnesium has long been known as the lightest of our engineering metals. This metal, silvery white in color, has a specific gravity of only 1.74. Aluminum, the next lightest structural metal, is 1 ½ times heavier; zinc is 4 times heavier; iron and steel are 4 ½ times heavier; and copper and nickel are 5 times heavier. Magnesium does not occur in the free state but is very abundant in nature, constituting 2.5 pct of the earth's crust in the form of various ores. It is the third most abundant structural metal, being exceeded only by iron and aluminum. Magnesium is unique, however, in that in the form of magnesium chloride it also exists in the oceans. Sea water is the source most widely used for production in the United States but magnesium is also commercially produced from magnesite, dolomite, and other ores as well as from certain inland brines. The vast quantity of magnesium existing in the waters of the oceans can be visualized when it is realized that the removal of one hundred million tons per year (the approximate annual steel production in the United States) for a million years would reduce the magnesium content of sea water only from 0.13 to 0.12 pct, providing no more magnesium had washed into the sea in the meantime. Not only is magnesium potentially very abundant but it is in addition a very versatile metal and can be shaped and worked by practically all methods known to the art of metal working. It can be cast by sand, die, and the various permanent-mold methods;

Jan 1, 1953

By Colin M. Sargent

ALTHOUGH annealing twins are frequently observed in many fcc metals, their occurrence in aluminum is relatively rare. ~ahn' in his review of twinning has listed only a few references to observations of twins in aluminum, e.g., Refs. 2 and 3. They have also been shown to occur in evaporated aluminum layers.4 During the present work, several annealing twins were studied in aluminum. The specimens of 1099-grade aluminum had the following thermomechanical treatment: deformed 90 pct by rolling, partially re-crystallized, further deformed 60 pct to a final thickness of 100 p, then annealed for 24 hr at 120°C. This treatment produced several annealing twins—-about ten per electron microscope specimen. The specimens were produced by the window technique and examined in a Phillips E.M. 200 operating at 100 kv. A typical twin boundary is shown in Fig. 1. For several of the twins studied the twin plane could be tilted so that it was parallel to the electron beam, e.g., Fig. 2. The associated diffraction pattern, Fig. 3, shows the twinned relationship between the grains. The twinning plane in each case was (111). Use of a reflection common to both the twin and the matrix,* i.e., using reflecting planes parallel in the twin and the matrix, the coherent twin boundary becomes invisible and only the noncoherent segments of the stepped boundary are seen, e.g., Fig. 4. Trace analysis of the boundaries showed that the long straight portions were invariably the twin plane; i.e., these portions are coherent. The planes of the shorter segments are shown by Fig. 5 to be (551 1, (7111, and {211).

Jan 1, 1969

By Paul Weir

BLEACHING clays have been used extensively in the oil-refining industries for a number of years. Their use in water purification is relatively recent and less extensive. They are frequently classified as (1) those naturally active and (2) those active after artificial activation with acid. Fuller's earths fall within the general group of bleaching clays and gradually the commercial term "fuller's earth" has been applied to natural clays originating, for the most part, in the south-eastern section of the United States. Bentonitic clays are usually classed as activable and are prevalent in the southwestern section of the United States.1 Bleaching clays vary considerably in chemical and physical properties throughout the country, or even in different parts of one deposit (Table 1). TABLE 1.-Physical and Chemical Composition of Different Types of Clays Composition, Per Cent Constituents and Properties Bentonite Fuller's Mud Clay (Wyoming) Earth (P Peak)' (Alluvial) Silica (SiO2) 60.0 69.6 61.67 Alumina (Al203) 19.0 14.3 20.34 Ferric oxide (Fe203) 2.8 3.90 7.70 Titanium oxide (Ti02) 0.13 0.70 1.01 Lime (CaO) 0.5 0.80 0.00 Magnesia (MgO) 2.0 1.00 0.24 Soda (Na2O) 2.4 0.40 0.31 Ignition loss 4.7 6.77 8.51 Moisture content 8.0 10.0 20.0 Isoelectric point, pH 9.2 9.2 6.5 Average swelling volume 15.0 0.0 0.0 Weight per cubic foot, lb 55.0 40.0 65.0 Material passing 200-mesh sieve, per cent 90.0 85.0 50.0

Jan 1, 1939

By J. C. Fisher

THE following facts are reasonably well established concerning the influence of boron on the hardenability of steel:1-4 1—Boron does not appreciably influence the ther-

Jan 1, 1955

By William L. Payne, Edward E. Ives

A unique feature of Potash Co. of America's A new potash property near Saskatoon, Sask., is the use of semi-dome-shaped buildings for product storage. Four domed structures, timber-framed and corrugated-sheet covered, are being built; each designed to handle 20,000 cu yd. The relatively small capacity units, PCA believes, give flexibility not only in storing different grades and sizes of product, but also in permitting greater ease in shipping products as market demands change. The domed buildings are 150-ft diam, comprised of a 16-ft-high concrete wall base, topped with a metal sheet-covered octagonal timber frame. The dome of each unit is designed to fit very closely the angle of repose of the contained material, which results in the maximum usable volume. The entire roof is flood coated with a bitumin to provide a complete weather seal.

Jan 9, 1959

By Sir Robert Hadfield

(New York Meeting, February, 1913.) THE Hadfield method of producing sound steel ingots has been the subject of a paper 1 read before the Iron and Steel Institute, so that it will be unnecessary to describe it fully here. The object of the method is to make possible the production of steel ingots in which the pipe is almost entirely obliterated, and it is applicable particularly to the production of sound ingots, from which good rails could be rolled. The method in brief consists in casting the ingots on cars, usually with the small end down. Each ingot mold is provided with a sand top, rammed up in the well-known manner. After the mold is filled to the desired height with steel, a layer of slag about 0.5 in. thick is placed upon it and the balance of the mold is then filled with charcoal. Then, through suitable piping, an air blast is directed in numerous jets upon the charcoal, which is burned thereby, the combustion supplying additional beat to the top of the ingot, which helps to keep the top fluid and to retard its solidification, while the lower parts are rapidly losing heat by its transfer to the mold. By-one plan the ingots are cast in molds placed upon bogies, movable trucks, or platforms, in the position A, Fig. 1. The ingots are cast vertically on bogies, say four or more ingots on each bogie, as may be found most convenient, and the upper surface of the steel is maintained in a molted condition during the transit of the ingots from the casting pit to the stripper. This is effected by a series of air pipes, for example, three in number, with jets or holes on the under surface of such pipes, placed preferably horizontally, arranged in such a manner as to cause jets of air to impinge on the upper surface of the ingots. These holes or jets are made throughout the entire length of the overhead pipes, the length of such pipes being

Jan 4, 1913

By W. R. Foster, J. M. McMillen, A. S. Odeh

The complete equations of average linear momentum balance for a single-phase fluid in an incompreisible, homogeneous, porous medium are derived. The derivation begins with Euler's equation of motion for a continuum and uses an integral transform recently developed by Slattery. 7 For steady flow of a compressible, Newtonian fluid, the usual equations of motion result. For transient flow, the space-time description of the pressure is determined in the lowest approximation by the telegrapher's equation. From the analysis a new phenomenological coefficient results which connects the viscous traction to the deriv ative of the linear momentum density. The magnitude of this coefficient determines the velocity of sound through the pore structure in this approximation to the pressure field. INTRODUCTION The modification of Darcy's law of momentum balance for steady, single-phase flow through porous media has been discussed for many years. The first modification was suggested by Forcheimerl who added terms of higher order in the velocity. These can be expected to appear because the underlying microscopic equations of momentum balance are themselves nonlinear in the point velocity field. The Reynolds tensor pvv, which represents the convective flux of momentum density, appears in the momentum balance equation. Only in rectilinear flow (parallel stream lines) does the divergence of this tensor vanish. Since the steady flow stream lines in most porous media are not parallel, nonlinear dependence of the pressure gradient on the velocity should naturally appear. This nonlinearity has nothing to do with turbulence in the ordinary sense of random fluctuations in the pressure and velocity fields. It arises simply because the stream lines converge and diverge, even for steady flows. Klinkenberg2 demonstrated that the permeability coefficient in Darcy's law depends on the absolute pressure or, alternatively, on the density field. However, because he neglected inertial terms of the Forcheimer type, his correction coefficient could not be represented by a constant but tended toward a constant as the velocity decreased. Forcheimer's and Klinkenberg's modifications can be combined in a rigorous way to account for both inertia and slip during steady flow. This will be shown in a future paper. The transient change of pressure in porous media has been described by the diffusion equation.3 This form results from eliminating the velocity and density fields from a combination of the equations of motion in the form of Darcy's law, the continuity equation and an equation of state. Fatt4 suggested that the cause of deviations from the prediction of the diffusion equation for pressure transients lies not in the choice of Darcy's law as the equation of motion but on the existence of dead-end pores which might invalidate the averaged equation of continuity. On the other hand, Oroveanu and Pascal5 noted chat the time derivative of the momentum density must be included in the equations of motion since this measures the local rate of change of momentum density. Their differential equation for pressure is the telegrapher's equation (neglecting gravity). However, their form of this equation predicts that the speed of pressure propagation through the pore structure is the same as that through the bulk fluid. M. K. Hubbert6 attempted a derivation of Darcy's law by volume averaging the Navier-Stokes equations. Since these equations represent momentum balance at a point within an open set of points containing the fluid itself, Hubbert's volume averaging cannot lead to tenns involving transfer of momentum between the fluid and the walls of the pores. Once these viscous tractions are lost by choosing a control volume containing only fluid, they cannot

By R. S. Dean

True careful work of Gross and Zimmerley1 has established the fact that the energy actually used in grinding is proportional to the new sur-face produced. This confirmation of Rittinger's law was made by crush-ing quartz in a frictionless drop-weight machine and determining the surface of the quartz by its rate of solution in hydrofluoric acid. The details of this procedure have been described adequately elsewhere and need not be repeated here. The resultant data furnish the only available basis for comparing accurately the efficiency of grinding machines. This method is so cumbersome experimentally that it has been little used. As an alternative all sorts of approximations have been proposed. The best of these is complete size analysis by sieving and elutria-tion. Such procedure is very lengthy and difficult to carry out accurately. Furthermore, any sizing method becomes very inaccurate for determining surface with very fine sizes where the ratio of surface to volume becomes very large. To avoid the lengthy and difficult technique of elutriation it has been proposed to estimate the size distribution below 200 mesh from various probability formulas. Such a procedure is at best an engi-neering approximation; at worst it is a mere guess. Some time ago Dr. V. H. Gottschalk2 found that the coercive forces of magnetite powders were directly proportional to the surface area, regard-less of size distribution. It was at once apparent that this furnished a method for determining grinding efficiency quickly and accurately. The only requirement was a single determination of the relation between the work input of the Gross-Zimmerley drop-weight machine and the coercive force of the resultant crushed magnetite.

Jan 1, 1936

By R. Q. Shotts

Nitric acid oxidation rate analyses of three coals, previously studied microscopically by the Bureau of Mines, revealed three components. Relative quantities agree with those found for the four components given by the Bureau and results are consistent with current ideas of coal constitution. Possible multi-component composition for bright coal and a reactivity-rank relation are suggested. THE physically dissimilar components of bituminous coals often are easily recognized mega-scopically. Under the microscope, reflected light or light transmitted through thin sections reveals the presence of the different components, even when these are intimately mixed. Optical methods for the quantitative estimation of the relative abundance of the various components, both by means of thin sections and by particle count, have been fully described.'. ' It has long been recognized that there are chemical and physical differences between the various petro-graphic components of bituminous coals, although analytical differences usually are small.:'. ' Only in the case of fusain have chemical differences been used for quantitative determination of a component. C. C. Hsiao and associates, at the Mineral Industries Experiment Station of the Pennsylvania State College, have described a method of analysis which is based upon the differences in the rate of nitric acid (8N) oxidation, fusain, and the other components of coal."," The reproducibility of their method and its applicability in checking microscopic determinations of fusain content have been supported by several independent investigations.'. " The writer has proposed the use of differences in oxidizability for the estimation of other components." "' The results of the oxidation of whole coals and of float-and-sink fractions of coals were reported. In most cases the plots of the logarithms of the percent dry, non-fusain, organic residue from oxidation, against time, revealed the presence of at least two distinct components. Both components appeared to oxidize according to a first order law, but the reaction constants for the components were distinctly different. One or more of the dull density fractions were found to contain but one component, and some of the lower rank coals oxidized in such a way as to suggest the presence of three components. A suitable way to check the identity and significance of the components delineated by oxidation would be to analyze a sample of coal both by the nitric acid oxidation procedure and by a microscopic method. The writer was wholly unfamiliar with either of the microscopic techniques commonly used, and to make such a comparison it was necessary to rely upon microscopic analyses made by someone else. It is hoped that some laboratory which is equipped to make both types of analyses will some day make them upon identical samples. During the past 20 years, four Alabama coals have been analyzed petrographically and the results published by the United States Bureau of Mines. They are: 1—Flat Top mine, Mary Lee bed; 2—Empire mine, Black Creek bed; 3—Wylam No. 8 mine, Pratt bed, all in the Warrior field; and 4—Soot Creek mine, Fairview bed, in the Coosa field."-" Of these, only the Flat Top mine is still operating. Because of the closing of these mines, it first appeared necessary to rely upon the indirect and unsatisfactory procedure of sampling the beds in other mines located as near to the closed mines as possible. Upon investigation, however, it was found that the Bureau of Mines still had, in storage, the very same samples which had been used in the published petrographic studies. The Bureau very generously furnished about 2000 g each of the Pratt, Mary Lee, and Fairview bed coals, largely lumps but with some fines. The blocks of coal, when received, still were covered by the paraffin coating which had been placed on the polished surface, in the case of the Mary Lee coal almost twenty years ago. Procedure The procedure for oxidizing the coal sample and removing the alkali-soluble humic acid has been described. In the present study, oxidation periods of 1/6, 1/3, 1/2, 3/4, 1, 2, 3, and 4 hr were used. All oxidations were made in triplicate. After the paraffin had been removed in boiling water and the coal washed carefully with cold benzene, the entire sample of approximately 2000 g, obtained from the Bureau of Mines, was crushed to pass a No. 4 sieve. About 200 g of this material was pulverized to pass

Jan 1, 1954

By R. Adair, W. R. Hudspeth, W. T. McDaniel

ANEW method for concentrating the flake mica either from present washing plant tailings or from new feed has been developed. In this paper, flake mica refers to that which occurs in weathered granites, alaskites, pegmatites, and schists in a form too fine to be considered sheet mica. It ranges in size from 1 in. or more down to 200-mesh or finer and occurs with kaolin, quartz, and partially kaolinized feldspar. Scrap mica, a term often used indiscriminately to describe everything other than sheet mica, will be used to denote the waste product from sheet mica mines and fabricating plants. Both flake and scrap mica are used in the mica grinding plants to produce wet-ground or dry-ground mica, although some flake mica recovered from clay mining operations is fine enough to be marketed without grinding. Until 1930, ground mica was made almost entirely from scrap. From 1930 until 1935 a gradually increasing amount of flake mica was mined, and most of this was sold without grinding. A large percentage of this mica was recovered from clay washing plants. In this type of operation the recovery of any sheet mica was .of secondary importance and was considered a byproduct. North Carolina produces more flake mica than any other state, accounting for 73 pct of the total domestic production.' In the following review of current practice in jig plants, there is no intention to disparage these operations. Within the limitations under which they were built, they are examples of mechanical ingenuity. The term jig plant is a carryover from early practice since there are no jigs in operation at the present time. Current practice, as shown in Fig. 1, is based on successive stages of differential crushing with rolls followed by trommel screens to remove the more easily crushed gangue minerals. The oversize mica product then is usually dried, and passed through another set of dry rolls and a final screen to remove the remainder of the grit. This process is effective in recovering up to 50 pct of the mica in the original ore, the balance being lost in the screen undersize, usually —% in. Jigs and tables were at one time used to treat this screen undersize and were capable of recovering a part of the mica larger than about 60-mesh.V ine mica lost in these plants is normally washed away in streams and can be considered irrecoverable. There are ten or more washing plants in the North Carolina area that are losing approximately 50 pct of the mica in the feed. Since the three cooperating agencies, the Asheville Minerals Research Laboratory of North Carolina State College, the North Carolina Dept. of Conservation and Development, and the Tennessee Valley Authority, are concerned with conservation of minerals, they have investigated means for improving the efficiency of these mica plants. The mica industry has been cooperating fully with the laboratory to establish a more efficient method of recovery for flake mica. Choice of Methods The initial investigation was concentrated on finding a means of reducing the losses from plants now using the conventional flowsheet shown in Fig. 1. To accomplish this it would be necessary to collect the screen undersize products through the plant and remove from them the mica from Vs in. down to

Jan 1, 1952

By Walter Wood

The specifications for cast-iron pipe that have been submitted at this meeting are practically the outgrowth of those which were originally adopted, about 1860, by Mr. Kirkwood of Brooklyn, N. Y. They have been changed but little since that time, the mode of testing pipe in the hydraulic press, as well as the method of coating, not having departed from the original practice. The chief addition to the specifications has been in the adoption of a test-bar 2 in. by 1 in. in crosa-section, broken between 24-in. supports by a transverse strain applied on the flat side. Test-bars were first introduced into pipe-specifications about 1870. At that time a satisfactory test-piece had to stand a tensile strain of 16,000 lb. per square inch. The present test-bar was adopted in order to give some idea of the deflection of the iron that was being used. These deflection-tests have been so satisfactory to both engineers and manufacturers, and have met the requirements of the pipe-trade so accurately, that it is considered best to hold to the . 2-in. by 1-in. bar instead of adopting the short " Arbitration Bar," which yields but little information from the stand-point of deflection. The new feature in these specifications is the effort to reach standards to which pipe shall be cast in the future, thus permitting the manufacturer to make up stock and the purchaser to find material on hand when he asks for deliveries. Heretofore there has never been ally standard weight for pipes? although in some sizes certain weights are more frequently asked for than others. The fixing of standards for pipes permits the adoption of definite standards for fittings. It has been aimed to secure such uniformity for fittings as will permit the same class of fittings to cover two or more classes of pipe. In order to accomplish

Jan 1, 1905

By A. K. Mukherjee, John E. Dorn

The effects of strain rate and temperature on the critical resolved shear stress for (321)[111] slip were determined for the silver-rich CsCl type of intermetallic compound AgMg. The flow stress increased only slightly as the test temperature was first decreased below room temperature; a rapid increase in the flow stress was obtained with yet further decrease in temperature from about 250' to 4OK. The effect of both the temperature and strain rate on the flow stress over the low-temperature range could be rationalized satisfactorily in terms of the Peiwls mechanism when the deformation was controlled by rate of nucleation of pairs of kinks. IN spite of the well-documented interest of metallurgists and engineers concerning the mechanical behavior of intermediate phases and intermetallic compounds, very little definitive information is available on this important subject. As recently summarized by westbrook,1 only limited and modest progress has been made thus far in elucidating the details of the mechanism of plastic deformation for the intermetallic compounds; the available information largely concerns phenom-enological descriptions of empirical observations and experimental facts, principally with reference to poly crystalline aggregates. The present report on the elucidation of the rate-controlling mechanism for slip in the bcc structure of AgMg is part of the comprehensive program of a systematic investigation on the mechanical behavior of intermetallic compounds. The intermetallic compound AgMg has a CsCl type of lattice structureZ and is completely ordered up to its melting point of 820c3 This material was selected for our present investigation because of its simple crystal structure, moderate and congruent melting point, ordered structure persisting up to the melting point, and some solubilities of the constituent elements, which could be expected to help in the growing of single-crystal specimens. Whereas previous investigations on the properties of AgMg include hardness,*"6 slip systems,7 tensile flow stress of polycrystalline specimens,' and electrical resistivity,4 the current investigation will be directed principally at elucidating the rate-controlling dislocation mechanism responsible for slip in single crystals at low temperatures. It will be shown that the strain rate is consistent with a model involving the rate of nucleation of pairs of kinks by the Peierls mechanism for plastic deformation. EXPERIMENTAL TECHNIQUES Single-crystal specimens of the AgMg intermetallic compound were prepared and tested as follows: 1) A master alloy ingot of AgMg was produced by melting and chill casting the high-purity silver (99.995 wt pct) and high-purity magnesium (99.997 wt pct) in an induction furnace under a helium atmosphere. 2) Sections of the above-mentioned ingot were placed in a graphite mold containing a spherical cavity in which a single-crystal sphere of 1 in. diam was grown under helium by the Bridgman technique. 3) The operative slip systems were investigated at room temperature on a singlecrystal of AgMg, from measurements of the angles made by the slip traces on the two surfaces of the specimen, which were at 90 deg to each other. The investigation confirmed that the AgMg compound undergoes slip primarily in the (321) plane and in the [Ill] direction, but a small amount of secondary slip was also noticed in the (112) (111) system. No slip was observed in the (110) planes. 4) The single-crystal sphere, mentioned earlier, was oriented in a graphite mold containing a cylindrical cavity of 3/8 in. diam above the spherical receptable to give the angle xo = 45 deg between the axis of the cylindrical bar and the normal to the slip plane (321), and the angle AO = 45 deg between the slip direction [Ill] and the axis of the bar. Oriented single-crystal bar seeds were produced by melting, under a helium atmosphere, a polycrystalline bar in the cylindrical cavity above the oriented spherical seed and by growing an oriented single-crystal bar from the seed. 5) Finally, oriented single-crystal specimens were grown from these cylindrical seeds. 6) The cylindrical specimens were machined in a High-Tension Spark Cutting unit to give a 2-in. gage length. The spark-machined gage section was elec-tropolished in a bath containing 200 ml of H3PO4,

Jan 1, 1964

By B. C. Allen

Surface free energy and surface self-diffusion of solid molybdenum were studied in the temperature range 1600" to 2400°C using pressure-sintered bi-crystals. Comparison of groove angles formed in various surfaces perpendicular to the grain boundary indicate a maximum of 1 pct variation in surface free energy with crystallographic mientation. This anisotropy tends to decrease with increasing temperature. The surface diffusion of the bicrystals is equivalent to that of sheet with a mild (100) Preferred orientation. Anomalously low values found for bi-crystals with surface orientations of (OOl), (012), and (011) are rationalized in terms of anisotropy in surface free energy. THE effect of crystallographic orientation on surface free energy1,' and surface self-diffusion3,4 has been primarily studied in fcc metals. The object of this work was to study the effect of orientation on surface diffusion and surface free energy of bcc molybdenum using pressure-sintered bicrystals. EXPERIMENTAL WORK Materials and Crystal Preparation. Arc-melted molybdenum rod was obtained commercially and electron beam zone refined at 50 cm per hr at 10- 5 torr to form single crystals about 8 cm long and 0.65 cm diam. Three crystals were prepared with axial orientations about 1 deg from [001.], [011], and. [111]. To reduce the carbon content, the crystals were annealed 2 hr in 1.4 atm flowing wet hydrogen at 2050°C. Then the oxygen content was reduced by annealing for 2 hr in -30°C dewpoint hydrogen at 2020°C. The resulting impurity analysis is given in Table I. Bicrystal Preparation. The single crystal rods were cut into transverse slices with a thin silicon carbide abrasive wheel to produce specimens about 0.6 cm long. They were mounted in epoxy and surrounded by stainless steel washers. Cutting in half was done longitudinally at various angles to known crystallographic planes containing the cylinder axis according to Fig. 1. To reduce surface deformation resulting from the cutoff wheel and thus reduce parasitic grain boundary formation on subsequent annealing, about 0.003 cm was manually ground off each cut surface with 600 grit paper. Care was taken to keep the surface flat. After removal from the mounts, one half was generally ro-tated 180 deg with respect to the other to give a po- tential symmetrical tilt grain boundary between the two halves. In the other cases when low misorienta-tion angles were desired, the crystals were not rotated. On the basis of symmetry, sufficient bicrystals were prepared to cover the entire range of misorientations for symmetrical tilt boundaries. The misorientations, +, ranged from 0 to 45, 0 to 90, and 0 to 60 deg for [001], [011], and [111] bicrystals, respectively. One [Ill] twist bicrystal was prepared from 2 single crystal discs rotated 17 deg relative to each other. Each specimen consisted of two pieces which were placed in a cylindrical tantalum can. Sharp edges were rounded and the fit was made as snug as possible to reduce subsequent deformation during bonding. The assembly and crystals generally were vicuum outgassed at 900" or 1700°C and then electron beam welded in the can at l x 10-4 torr. After being leak checked, the samples were placed in an autoclave and hydrostatically gas-pressure bonded5 in four batches under helium at 10,000 to 18,000 psi at 1650°C for 3 hr. Satisfactory bonds were obtained in many cases, and most of the crystals bonded after two exposures. The results did not appear to be affected by the various pressures used, preannealing conditions, crystal orientation, or time-pressure-temperature route taken to the final bonding condition. After bonding, the tantalum cans were selectively removed in cold concentrated HF. Measurements indicated overall deformation was under 1 pct. The bicrystals were metallographically ground and polished flat and perpendicular to the axis. Examination showed the boundaries were straight and almost free of parasitic grains caused by extraneous local deformation. Annealing. In preparation for thermal grooving, the bicrystals were cleaned and annealed by outgassing at 10-5 torr at 1900°C and heating at 2300°C under 1 atm 99.996 Ar for 0.5 hr. The crystals were held in a closed 4-deck box made of molybdenum sheet, and were heated in a Ta-1OW resistance furnace. The ar-

Jan 1, 1970

By B. Blumenthal

THE present investigation was planned as a survey of the lead-rich portion of the ternary lead-antimony-silver system by thermal analysis. Since, however, a rigorous application of the conventional thermal analytical method is time consuming, an attempt was made to speed up the investigation by reducing the time required for a single thermal analysis. This was done by increasing the rate of cooling to 12° to 18°C. per minute. Since such a rate does not permit even an approach to equilibrium conditions, the melt was stirred vigorously by a stirrer operating at the high rate of 665 r.p.m. This proved to be effective in obtaining cooling curves with distinct points of arrest and of excellent reproducibility, which satisfactorily compare with those obtained at a rate of 1° to 2°C. per min. with or without slow stirring (Fig. 1). By this method the lead-rich end of the lead-antimony system and a series of ternary alloys in sections parallel to the lead-antimony side of the ternary system were investigated and it was observed that the two branches of the' liquidus curve of the .binary alloys did not intersect at the eutectic temperature. An equivalent effect was observed in the ternary system. The eutectic temperature of the binary lead-antimony system was found to be 252.0°C., which confirms the recent investigation by Pellini and Rhines,1 who determined the eutectic temperature to be 251.5°C. The observation that the curves of primary crystallization of the lead-antimony system do not intersect at the eutectic temperature was previously made by Dean.2 Dean explains the phenomenon by assuming the existence of a compound Sb4Pb. He felt that super-cooling was not the cause of the phenomena because he was unable to influence them by inoculation. The X-ray investigation by Solomon and Morris-Jones,3. the metallographic investigations by Stead,4 Charpy,5 Gontermann,6 and Dean, Zickrick and Nix,7 and the numerous investigations of physical properties, definitely disprove the occurrence of any compound. The work of Dean was not confirmed by Broniewski and Sliwoski,8 whose experiments did not show any irregularity and who report a eutectic composition of 13 per cent antimony and a eutectic temperature of 250° to 252°C. at a rate of cooling of about 6°C. per min. Abel, Redlich and Adler9 then report a eutectic composition of 12.1 per cent upon reviewing the previous, publications and adding a few of their own cooling curves. In 1934 Quadrat and Jiriste10 found from careful analyses of the bottom portion of slowly cooled hypereutectic melts that the eutectic contains only 11,4 to 11.5 per cent antimony. (Previous analyses by Stead4 in 1881 gave 13 per cent:) Weaver," however, reported in 1935 that cooling curves indi-

Jan 1, 1943

By W. R. Webb, M. O. Peterson

WHEN men drive haulage equipment ranging up to 22 tons in an open pit operation, they must live with the realization that their safety is dependent upon the machines they drive and how well they operate them. The hazards inherent in their jobs must be recognized, met, and defeated. It comprises a never ending struggle toward perfection-an almost un- obtainable goal. The Jones & Laughlin Benson Mines, at Adirondack State Park in New York, created a safety program which resulted in only one three day lost time accident from April 1948 to April 1952. At the very start of the program, management of the open-pit operation recognized the hazards existing at Benson. The program was designed to meet each danger. With a knowledge of the problem faced, the process of minimizing each facet was planned along lines of maintenance of equipment and training of personnel. Its success is evident. In the ever-present struggle, care and maintenance of machines and application of experience to new equipment design are mainstays. Truck Haulage Benson produced 2.9 million tons of crude iron ore and 1.6 million tons of waste in 1951. To do the job, truck mileage reached 500,000 miles. The tremendous mileage emphasized to safety planners, the fact that the more work done, the greater the possibility of risk in haulage operations. Instrumenting the aim of the safest equipment possible is a methodical servicing program. Like other segments of the drive, the servicing program is based on greater production with fewer accidents. Every truck is serviced at least once per eight-hr shift. Examination includes inspecting and tightening wheel studs, checking tires, steering apparatus, lights, brakes, wipers, heaters, fire extinguishers, and refueling. A running history of the equipment's operating life is kept in the form of service and maintenance records. Machine operators are constantly on the alert for malfunctioning of units. At the first sign of trouble the truck is returned to the garage for exchange. No truck functioning incorrectly is kept on the line, regardless of its shift check schedule. The program resulted in a reduction of the number of costly overhauls and cut down the number of haulage accidents. Miscellaneous Mobile Equipment Auxiliary units, operating within the pit, have presented definite safety problems. The highest accident rate in the pit occurred on trucks carrying water and bits to the churn mills. The weight and awkwardness of bits and drill stems, combined with remote delivery points were direct causes of numerous accidents. Here, the problem has been one of equipment handling, rather than haulage. All air compressors for secondary drilling are truck mounted, facilitating mobility. In addition to making it easier to move the equipment, truck mounting has eliminated many of the hazards connected with relocating machinery. By making air compressors independent of other units, drilling operations have been speeded up considerably. Unseen rocks in the path of moving vehicles are a constant source of tire damage. At Benson the problem has been met by supplying each loading crew with a bulldozer for cleanup operations. The pitman directs the dozer operation, and when truck drivers back into loading areas, he serves as an extra set of eyes. Modern Truck Garage Provides Drive-Through Service Simplicity is the essence of any preventative maintenance program. At Benson, a modern garage, with a drive-through service bay simplifies servicing. Shift inspection of the 22-ton haulage units is accomplished with minimum delay and maximum thoroughness. Major repair work and periodic overhauls are done in the repair section of the truck garage. Crane facilities for handling heavy assemblies ease the job and add to the safety factor. Other mobile machinery,

Jan 1, 1952

By Michael B. Kahle, Fred J. Scheaffer

Production scheduling, along with production planning, provides projections of future mining progress and time requirements for the development and extraction of a resource. These schedules and plans are used by management as a means of attaining the following objectives (1) maintaining or maximizing expected profit, (2) determining future investment in mining, (3) optimizing return on investment, (4) evaluating alternative Investments, and (5) conserving and developing owned resources. The first four goals are generally concerned with mining costs, both capital and operating requirements, and as such, play an important role in production planning. However, this chapter is concerned with the fifth management objective of resource development in order to conserve and perpetuate the corporate entity. The following discussion is based on the premise that detailed economic evaluations and market surveys have been performed and analyzed and that the results indi¬cate a viable project.

Jan 1, 1979

By K. M. Rolls, J. Wulff, D. A. Colling

Solid-solution alloys of the Ta- Ti system containing up to 70 at. pct Ti were melted and fabricated into wire. Steady magnetic-field measurements of cold-worked wires at 4.2°K indicate that the resistive critical field increases smoothly with increasing titanium, reaching a maximum of 93 kG (J = 1 amp per sq cm) for a composition of about 50 at. pct Ti. The composition dependence of the resistive critical field indicates it is largely paramagnetically limited for alloys containing more than 35 at. pct Ti. For cold-worked wires the value of the critical current density, Jc , was found to be insensitive to composition changes for compositions in excess of 20 at. pct Ti. It was observed that Jc could be increased by final-size heat treatment at 400°C without altering the value of- the resistive critical field. Experimental data are used to calculate the electronic specific-heat coefficient and the "upper critical field" for the alloys studied. THE effect and importance of metallurgical structure on superconducting properties have been summarized by Livingston and Schadler.1 Specific work on solid-solution alloys such as Nb-zr2-7 and Nb-Ti5-7 have shown that critical current density (Jc) and superconducting transition temperature are structure-sensitive. Berlincourt et al.6,8,9 in their studies of transition-metal alloys find that Ta-Ti alloys remain superconducting at fields comparable to Nb-Ti alloys. 6,8 Transverse critical current tests of a Ta-10 at. pct Ti alloy10 and longitudinal critical current tests of a Ta-25 at. pct Ti alloy1' indicate that such alloys are capable of carrying high currents at intermediate fields (-40 kG). The work reported in the present paper was undertaken to explore the superconducting properties of further compositions in the Ta-Ti alloy system as well as the structure sensitivity of the superconducting properties. I) EXPERIMENTAL PROCEDURE Alloys were prepared by melting tantalum (Fansteel Metallurgical Corp., 99.96 pct purity) and iodide, crystal bar titanium (Foote Mineral Co., 99.92 pct purity) mixtures in an arc furnace on a water-cooled copper hearth using a tungsten electrode. Melting was accomplished in a purified, gettered argon atmosphere at pressures from 250 to 400 Torr. Each alloy was turned and remelted fourteen times to assure complete mixing of tantalum and titanium. Ex- cessive coring in the cast samples was, nevertheless, observed. This was somewhat reduced by annealing in vacuo at 1000°C for 13 hr. The ingots were then machined to 0.250 in. diam, jacketed in Type 304 stainless-steel tubing, and swaged to 0.140 in. diam. They were then drawn to 0.010-in.-diam wire. Alloys containing up to 70 at. pct Ti were readily cold-drawn to wire in this manner. Later experiments showed that oxygen additions up to -3000 ppm could also be cold-worked into wire. Test samples for superconductivity measurements in the 2-in, air-core Bitter solenoids of the M.I.T. National Magnet Laboratory were prepared from 10-in. lengths of 0.010-in.-diam wire, cleaned of residual wire-drawing lubricant. Current contacts were made by clamping clean copper tubing over both No. 18 current lead wire and the ultrasonically indium-tinned ends of the specimen wire.12 Potential leads of No. 32 copper wire were connected to the specimen by ultrasonic soldering in an indium bath. The potential lead separation was about 4 cm, corresponding to the circumference of the Bakelite rod to which the wire was affixed with half-mil Teflon tape. The final specimen configuration is shown in Fig. 1. Specimens were lowered into a liquid helium bath (4.2oK) in a double solenoid dewar and positioned so that the maximum magnetic field was oriented transverse to the wire axis of the gage section. Measurements were made by passing a current through the specimen at a preset solenoidal magnetic field. The current was increased until a 1-pv potential difference appeared across the gage section (1/4 µv per cm). At low magnetic fields, however, it was not possible to use this criterion because power-dissipation difficul-

Jan 1, 1967

SECTION I Page Page New York Section War Meeting on Employment xxxii Sulphur and Pyrite v Local Section News xxxiv War Minerals Committee xviii Forthcoming Meetings xxxvi St. Louis Meeting xx Library xxxvii Minutes, of Meeting, Executive Membership xli Committee xxvi Institute Committees Iv Members in Military Service xxvi Officers and Directors lxii Personal xxx

Jan 10, 1917

YEARS ago, when metal mining was more an adventure than a well-organized business, it was often said (with some color of truth) that unless a mine could stand bad management or mismanagement, it was not much good. Today, the natural excellencies of an ore deposit are merely a challenge to the engineers to exploit it as skillfully, as efficiently, and as profit- ably as possible. A vast amount of competent and imaginative engineering management (which includes economic analysis no less than the technologic arts of mining ore and treating it) has been required to make New Cornelia the smooth-running and successful operation that can be seen at Ajo today. New Cornelia was acquired by the Phelps Dodge Corporation when it absorbed the Calumet and Arizona Mining Company in 1931. Next to Morenci, it doubtless is the corporation's biggest asset. It in no way detracts from the achievement of Phelps Dodge engineers to say that they had an admirable ore deposit to work on. New Cornelia ore, as mined, is relatively low in grade and the deposit is by no means the largest of the Porphyries; but it has these attractive features : (1) It is peculiarly suitable for opencut mining because: (a) The overburden of waste rock lying above the ore deposit was (it has long since disappeared) almost negligible. (b) The deposit is roughly circular in horizontal section, with the horizontal dimensions four to five times as great as the maximum thickness. (Nevertheless, eventually some underground mining may be desirable.)

Jan 1, 1957