Search Documents

By Maurice E. Peloubet

This discussion of accounting will describe the statements and the information that the accounting system produces, from the point of view of those who use such systems rather than of those who prepare them and who do the detail and technical accounting work. In any well organized mine, quarry, or other enterprise exploiting a mineral deposit, no matter how small, some clerical and accounting work must be done. Miners and other employes must be paid, supplies must be purchased and issued, and various tax and information returns, which even the smallest enterprise must file, have to be prepared. In this chapter it is assumed that the enterprise has employes of this type and that they understand the fundamentals of record keeping and accounting. It would be impossible here to give sufficiently full explanations to enable a man with no previous clerical and accounting training to set up and operate an accounting and cost system for even the simplest extractive operation. Rather, we shall hope first, to tell the investor and the operator, from the chief engineer or president down to a subforeman, what to expect from the accounting statements and records and how to use this information in his daily work; and second, that it will enable the man with some knowledge of accounting or bookkeeping, but with little or no experience in any extractive industry, to set up and operate a satisfactory system for a mine or other extractive enterprise. For readers who wish to go further, the bibliography at the end of this chapter contains many references. The emphasis has, therefore, been placed on the statements to be produced and the purposes for which they are to be used rather than the underlying books and records. These are, with a few exceptions which will be described later, essentially what might be found in any industrial enterprise and would probably, in the extremely small enterprise, consist of handwritten journals, ledgers, analysis books, payroll books, and stores ledgers. In the larger enterprise, various types of mechanical accounting would be introduced in proportion to the complexity of the operation.

Jan 1, 1959

By J. D. Prater, H. R. Spedden, E. E. Malouf

Application of research findings to the old art of leaching copper from copper-bearing mine waste has resulted in a significant contribution of copper to over-all copper production. For example, at the completion of the current expansion program at the Kennecott properties in the United States, copper produced from waste dump leaching will amount to about 25% of the total production, whereas formerly only 2% was derived from this source. This planned expansion of copper leaching focused attention on the problem of developing more efficient methods for the recovery of copper from greatly increased volumes of copper-bearing so1utions.l Detailed investigations made in laboratory pilot plant and plant tests for the recovery of copper from copper-bearing solutions have included electrowinning, solvent extraction, ion exchange and cementation with iron in launders, precipitation drums, activated launders, and precipitation cones. The results of these investigations have led to the development of a precipitation cone-type recovery system having advantages over older methods.

Jan 4, 1966

By W. C. Wright

A PRACTICAL program of education for workers of the mining industries is being formulated by the Federal Board for Vocational. Education in cooperation with the States in which this industry is a dominant one. The Federal Government last year passed a law, known as the Federal Vocational Education Act, that provides for the promotion of vocational' education and for cooperation with the States in the promotion of such education in agriculture and trades and industries and in the preparation of teachers of vocational subjects. More than 1,000,000 men in the continental United States are employed in mines and quarries. The following table, from the-1910 Census Report, shows the relative importance of mining and manufacturing pursuits: Manufactures Mines and Quarries Employees 7,405,313 1,109,410. Capital $18,428,269,706 $3,380,525,841 Value of product $20,672,051,870 $1,238,410,322 Of the more than 1,000,000 men employed in mining, almost three-fourths are engaged in the, production of bituminous and anthracite coal; one-fifth, in the production of copper, iron, lead, zinc, and other metals; and the remainder in getting out structural and miscellaneous materials from quarries. The meeting of the needs of the coal-mining industry, therefore, is the problem of greatest importance in the point of numbers to be served. Moreover, the dangers in coal mining are greater than in metal mining. Practically all States have set up educational and technical standards , for the position of foreman, boss, superintendent, etc., and every applicant for these positions must have a certificate of competency. The qualifications, too, are becoming increasingly difficult in the field of technical information. In some States, every miner must have a certificate, which is issued by the mine examining board. only after an oral examination.

Jan 1, 1919

By R. L. Curfman

In May 1960, six months after conversion of one- half of the Uranium Reduction Co. mill from acid to alkaline leach, severe corrosion was encountered in the 112 stainless steel wash baskets in the resin- in-pulp portion of the uranium circuit. Fortunately the corrosion was limited to the stainless steel screen cloth and bolts. The frames were not affected. Each resin-in-pulp wash basket serves as a container and a vehicle for approximately 40 cu ft of ion-exchange resin. Four baskets are installed in each tank through which uranium-rich solution flows as the baskets move up and down mechanically in the tank. The ion-exchange resin has an affinity for the uranium in the solution which causes it to be deposited on the resin in solid form. By reverse action with different chemical solutions, the uranium may be stripped from the resin for further processing and purifying. This section is the first step in the actual recovery of the uranium.

Jan 9, 1962

By Nelson Severinghaus

Consolidated Quarries Corp. must conduct operations for an average sales price of $1.25 per ton, about the same price at which stone was sold 25 years ago when the dollar was worth twice what it is now. To maintain success in a competitive business, the company must solve the usual production problems, which will be discussed here in the order they occur in the flowsheet. Most crushed stone quarries must first remove soil and decomposed rock. Although seasons of lower sales sometimes release regular quarry excavating and haulage equipment for this purpose, overburden is often too extensive for this method to be used. In such cases, special equipment must be assigned or the job may be contracted. As many earthmoving contractors have heavy duty specialized equipment well suited to overburden removal, they should be seriously considered before the job is undertaken. Pockets of clay beneath peaks of hard stone sometimes defy mechanized removal. Pick and shovel laborers at this point might be supplanted by more ingenious use of pumps and water or some other mechanical means. Where overburden is extremely heavy or difficult to remove, underground mining must be considered.

Mar 1, 1956

By Walter H. Ortel, George B. Wallace

INTRODUCTION A greater understanding is required about the factors which control tunneling operations if we are to meet the expected demand for tunnels. Much of the needed information can best be achieved by the proper use of instrumentation and advanced engineering concepts. Tunnel measurements and their analysis may prove to be the key which will give the insight necessary to understand the relationship of rock, tunnel supports, and linings. There are three main areas which can be improved through the use of tunnel instrumentation. First, and of prime importance, is safety for men and the project. When unstable conditions occur, sets become distorted. Even without measurements, it is sometimes possible to tell when trouble is approaching. In effect, the set acts as a load cell. Distortions in the set indicate reinforcements may be required to maintain stability. Additional sets or rock bolts, if they are placed soon enough, may provide this stability. However, when large rock displacements occur in short periods of time, it could be too late. Figure 1 is an example of the difficulties encountered in stopping moving rock. To stop the movement and possible failure, large props were placed above the spring line and the massive concrete gravity buttress was constructed along the legs. Rock bolts from the buttress deep into the rock were also used in an attempt to stabilize the rock mass. However, this work is for a highway tunnel and eventually these props and buttresses must be removed.

Jan 1, 1971

By E. J. Wasp, T. C. Aude, F. B. Raymer

Abstract-The following paper deals with technical aspects of terminal facilities for western coal pipelines. The information is taken from the Ohio and Black Mesa pipelines and the proposed one in Wyoming. This paper first discusses the feed terminal, the product that it must produce, and the reasons for coal cleaning. Then, in the delivery terminal section, the various methods of dewatering the coal and some recent innovative ideas on bunkering the dewatered product and storing the dewatered coal in large outdoor piles are discussed.

Jan 2, 1978

By J. S. Wakeman

INTRODUCTION The primary purpose of comminution circuits in the mineral industry is to reduce an ore to a particle size that will permit separation of the valuable minerals from its gangue constituents. Wide variations in the mineral content and physical characteristics can and do occur throughout a given mineral deposit From the standpoint of their effects on the comminution characteristics of an orebody, these variations may not be identified by the normal sampling and analysis procedures utilized to delimit an orebody and to characterize its grade distribution. The proper design of a comminution circuit for a mineral deposit is very important to the success of that enterprise. It is also an expensive unit process both from the standpoint of capital and operating costs. It is, therefore, essential that any sampling program be designed to identify the variations that may occur that will affect this circuit. Because of the variety of comminution systems that are available, it is also essential that the sampling and subsequent evaluation program be sufficiently comprehensive to identify potentially inappropriate systems or flowsheets. It would be impossible to describe in a single chapter the techniques and approaches that should be utilized for sampling every type of orebody. Each orebody is unique and requires a sampling and testing program designed to its specific requirements for exploration, characterization and circuit design. The following is a general discussion of the guidelines to be used and considerations to be made in establishing such a program. SAMPLE SELECTION When sampling an ore deposit for the purposes of equipment and flowsheet selection for comminution, it is important that the sample composites for grind testing be chosen on the basis of how they will affect the comminution circuit rather than just how they might affect the subsequent metallurgical operations. For example, grindability, classification and liberation size characteristics are more important to the comminution circuit than ore grade. Mineral deposits may contain a multiplicity of ore types that can vary extensively in the dissemination of minerals and optimum liberation size requirements; and may also vary as much as 100% in ore hardness. The accumulation of samples for grind characterization should be done in such a way as to allow the identification of this variation. A proper mineralogical evaluation of the samples obtained to characterize an ore deposit can be a great aid in identifying the individual ore types within the deposit

Jan 1, 1982

By William G. Pariseau

There are important phenomena in rock and soil mechanics that cannot be explained in terms of theories of homogeneous, isotropic materials. Subsidence of strata about mine openings is an example. In-situ stress measurements in nonisotropic sedimentary and metamorphic rocks is another. Patterns of joints, faults, fractures, and similar geologic features impart directional mechanical properties to rock masses that are locally isotropic or anisotropic. On the geologic scale, the nonhomogeneity of composite rock masses may, in certain instances, be dealt with as homogeneous anisotropy. The mechanics of large rock masses can, therefore, be expected to involve considerations of anisotropy. The source of the anisotropy is not relevant. Once the scale of observation is selected and the material is defined accordingly, the analysis of stress and deformation proceeds without regard to the numerical values of the material constants. There are also important phenomena in rock and soil mechanics that cannot be explained in terms of linear elasticity, theory. For the mechanical description of anisotropic geologic materials capable of deforming beyond the limit of purely elastic strains, a plasticity theory is required. The purpose of this chapter is to present a plasticity theory for anisotropic rocks and soils. The proposed theory is based on the work of Hill in anisotropic metal plasticity and represents an extension of his work so as to include anisotropic geologic materials. The point of departure from metal plasticity theory begins with the inclusion of the normal stresses as linear terms in the yield condition, which plays a central role in plasticity. Once the yield condition is established, the plastic strain increments are obtained immediately through the principle of normality. For practical applications, some simplification of the three-dimensional theory is re-

Jan 1, 1972

By William L. Grube

PECIMEN preparation for electron metallography involves several steps, such as polishing, etching, replicating, mounting, and shadowing. Although each step must be done with care, the operation requiring the utmost attention is etching. Proper etching is important because the relief pattern developed on the surface of the specimen by the etchant, and reproduced as minute differences in thickness of the replica, determines entirely the amount of detail seen in the final micrograph. The characteristic colored stains, sometimes used in light metallography to simplify identification of certain microconstituents, cannot be tolerated because there is danger of introducing artifacts in the replicating operation. It is also quite difficult to remove plastic replicas from stained specimens. A suitable etchant for electron metallography must, therefore, in all cases exhibit a preferential attack upon each of the microconstituents present sufficient to result in a difference in surface elevation. When only two microconstituents are present, it is not too difficult to find a suitable etchant since their physical or chemical properties are generally sufficiently different to result in a marked difference in attack by the etchant. For example, picral (a saturated solution of picric acid in methanol used as an immersion etch) is a satisfactory etchant for the specimen shown in Fig. 1 consisting of iron carbide particles embedded in a ferrite matrix.'

Jan 1, 1952

By L. Adler

A fairly complex analysis is required to select or evaluate a piece of excavating and bulk handling equipment for its performance. At present, there is little agreement as to what points should be considered, and even less on what procedure to follow. This paper provides both of these in a consistent and direct form. The analysis applies to all types and sizes of equipment. The importance of the equipment characteristics, job activities, and work conditions are stressed. Separate analytical stems are established in a flow chart for these. They are combined using suitability tests in: problem statement; natural conditions; suitability guidelines; appropriate equipment types; operational activities; encumbered space; geometric design; equipment sizing; failure and limits; performance and consumption; public policy checks; and costs and profitability. Public policy and economics receive emphasis towards the end. The procedure is iterative, containing distinct feedback loops. Specifying the steps and sequence provides a necessary structure which has long been overdue.

Jan 1, 1985

By H. M. Chance

WITHIN the last 10 years the subject of mine taxation in its relation to coal-mining interests has come to have growing importance, not only to those engaged in the mining of coal, but also to the owners of land underlain by coal. A disposition has developed among legislators to accept the principle, which has been laid down y many judicial decisions, that coal underlying the surface must be regarded as a part of the real value of all properties so underlain, and as such is chargeable with such burdens of taxation as the necessities of the government may impose. These necessities arise from the normal expense of maintaining State and local governments, and in the past have been met principally by, taxes based upon assessments of real estate values, which values in many cases have been confined principally or wholly to the value of the surface, without taking into consideration the value of minerals underlying the surface. It is not proposed here to deal with the question of Federal taxation, whether levied on production, or on products transported from one State to another, or exported from the country, or upon thegross or net earnings of corporations engaged in interstate commerce, or upon the production of materials which may be transported from one State to another, or levied. upon the profits or upon the obligations of corporations. The present discussion will be confined to the appraisal of coal lands as assessed for State, county, township, or borough taxation. The methods heretofore and at present in use in the different States vary widely and have resulted in more or less litigation. Discussions appearing from time to time in the technical and trade journals and in the proceedings of mining and engineering associations frequently direct attention to the need for the adoption of fixed principle in levying taxes, and of uniform methods for applying such principles, but there does not seem to be a general demand from the public for the adoption of such methods.

Jan 7, 1914

By Ralph Hultgren, David W. Mitchell

MAGNESIUM alloys usually are superheated before casting in order to ensure fineness of grain. Superheat temperatures in common use range from 1600° to 1700°F while the casting temperature, which depends upon the mold shape, is usually 200° to 300°F lower. The process of superheating requires considerable time and seriously shortens the life of the iron pots used. Recently it has been reported' that if acetylene, carbon dioxide or natural gas is bubbled through molten electrolytic A.S.T.M. No. 4 alloy at 1400°F. for 5 min., grain refinement equivalent to that of superheating will take place. Addition of certain solids such as graphite or aluminum carbide accomplishes the same results.2 As will be shown in this paper, it is possible to achieve grain refinement in magnesium casting alloys at low temperatures by mechanical stirring of the molten metal for a short time. This process was developed in the course of research work, supervised by the War Metallurgy Committee under the "Restricted" Project NRC-550, for the Office of Production Research and Development of the War Production Board. This paper, based on that work, has been released for publication by the O.P.R.D. MATERIALS AND METHODS The alloys studied were the most common American sand-casting alloys designated as No. 4 and No. 17 by the American Society for Testing Materials. The magnesium used in these alloys was of both carbothermic3 and electrolytic4 origin. Chemical analyses supplied by the producers are shown in Table I. Each heat consisted of approximately 5 lb. of alloy melted in a Tercod crucible. It was refined by fluxing with Permanente No. 7* refining flux at 1300° to 1350°F. After cooling to 1200' to 1250°F., portions of approximately one pound each were ladled into iron crucibles contained in an electric furnace at about 1250°F. The molten metal was covered with Permanente No. 21† covering flux and then heated to the temperature to be investigated. Normally each of the four portions was given a different treatment. In a typical case one portion was stirred vigorously for 5 min., acetylene gas was passed through a second portion for 5 min., a third portion was superheated to 1600°F for 15 min., then cooled to casting temperature, and the fourth was held for 5 min. at the temperature of stirring or gassing without other treatment. Each portion was then cast into one-inch diameter cylinders in three "nonturbulent" molds of identical shape. One mold was made of cast iron and the other two of baked sand. The cast-iron mold and one of the baked sand molds were heated to 360°F., the other baked sand mold was at room temperature. The freezing times in these molds were

Jan 1, 1945

[PRESIDENT AND DIRECTOR * R. R. McNAUGHTON, '63, Trail, B. C., Canada PAST-PRESIDENT AND DIRECTOR * JOSEPH L. GILLSON, '62, Wilmington, Delaware PRESIDENT-ELECT AND DIRECTOR * LLOYD E. ELKINS, '64, Tulsa, Oklahoma VICE-PRESIDENTS AND DIRECTORS * JOHN S. BELL, '62, Houston, Texas * A. B. CUMMINS, '62, Bound Brook, New Jersey * WAYNE E. GLENN, '62, Houston, Texas * C. C. LONG, '62, Monaca, Pennsylvania * J. S. SMART, JR., '63, New York, New York * J. W. WOOMER, '62, Pittsburgh, Pennsylvania]

Jan 1, 1961

By Richard Moldenke

So FAR as the quality of the product is concerned, the history of the production of pig iron for foundry purposes is one of constant retrogression. The steps in this deterioration began with cold-blast charcoal pig iron, then anthracite iron, coke iron; then gradually warm to hot-blast coke iron, with the charcoal furnaces also heating their blast to get greater tonnages, and finally the present day hot-blast coke irons with scrap additions to the ordinary burden that, according to one European report, have gone as high as 135 per cent. Parallel with this quality retrogression is the enormous increase in furnace tonnages from about 15 tons daily to over 1000 tons per day in exceptional instances of modern practice. The key to this situation is economic pressure. The effect is a growing differentiation between furnace production for gray iron and malleable foundries and for the production of commercial steel. As the foundry is often compelled to draw upon the pig irons made for steel purposes, for economic reasons, whereas the steel industry does not draw upon foundry pig irons proper, the situation is resolving itself into one of grave consequence for the life of the gray-iron castings industry, and hence the intensive present-day feeling in foundry circles for rigid specifications to govern the quality of pig irons sold for foundry use. In the discussion of a paper on the use of scrap in the blast furnace held recently in the Institute, a very pertinent remark was made by one of the participating furnacemen, who confessed that "the things found wrong by the foundryman with his iron were beyond his depth." It may be added that those things are also beyond the depth of most foundrymen who, however, know from their results that they are getting poorer castings today with many pig irons than they did with those same brands in former years. Under the former fracture buying, the foundryman at least could select the strongest metal, as judged by the sledge, from various brands of similar fracture and pig section, and his results proved the soundness of his conclusions. With the advent of iron analysis, and in spite of the growing uniformity of the metal through greater tonnage

Jan 2, 1927

By F. V. Tideswell

THE suggestion, which appears to find increasing favor, that the elementary composition of coals should be used as the basis of their classification, makes it important that our methods of expressing this elementary composition should be refined. It is doubtful whether many published ultimate analyses of coals are accurate within 1 per cent. carbon. Many are probably as much as 3 or 2 per cent. in error in carbon. It is, perhaps, not always realized that the extreme variation in carbon content over the range of bituminous coals is but 16 per cent. An error of 1 per cent. in carbon on analysis corresponds therefore with one-sixteenth of the whole range, an amount which is unjustifiable even for the application to commercial needs of a system of classification based on ultimate analysis. For the purposes of scientific research such limited accuracy is of little value. The object of this paper is to examine one important source of error in ultimate analysis, that due to the occurrence in coal of inorganic material, and to emphasize the need for the quantitative measurements (of carbon more particularly) on coals to be rendered independent of their contents of such material.

Jan 1, 1928

By G. A. Baird

With the exception of eight wildcat completions, which were unsuccessful and abandoned, all of the 1935 new drilling was performed in the proven fields. As of Dec. 31, 1935, 22 drilling rigs were in operation, of which 9 were at wildcat locations and the remainder were being used in new drilling in proven fields; in addition, 25 workover rigs (exclusive of cleanout rigs) were operating, all in the major fields. Production of Crude Oil.—Notwithstanding the considerable decrease in new completions during 1935 as compared with 1934, crude production mounted to a new high of 148,893,225 bbl., clean oil at 60' F., representing an increase of 12,532,579 bbl. over the previous record year, 1934, total of 136,360,646 bbl. This increase was due: (1) to the flush production

Jan 1, 1936

By G. A. Baird

With the exception of eight wildcat completions, which were unsuccessful and abandoned, all of the 1935 new drilling was performed in the proven fields. As of Dec. 31, 1935, 22 drilling rigs were in operation, of which 9 were at wildcat locations and the remainder were being used in new drilling in proven fields; in addition, 25 workover rigs (exclusive of cleanout rigs) were operating, all in the major fields. Production of Crude Oil.—Notwithstanding the considerable decrease in new completions during 1935 as compared with 1934, crude production mounted to a new high of 148,893,225 bbl., clean oil at 60' F., representing an increase of 12,532,579 bbl. over the previous record year, 1934, total of 136,360,646 bbl. This increase was due: (1) to the flush production

Jan 1, 1936

By W. J. Whiten

Current developments in one type of crushing and screening model is reviewed and general design techniques and policies are proposed for the control of crushing plants.

Jan 1, 1984

By R. Agarwal, S. Boshkov, M. T. Wane

The majority of the work done in the field of rock mechanics uses as a basis for analysis the classical linear theory of elasticity. Most workers in rock mechanics realize that removing the assumptions of homogeneity and isotropicity will bring the analysis of stress-strain relationships for geologic materials closer to reality. However, the algebra involved in reducing these restrictions is usually heavy. It is the purpose of this paper to relax the condition of isotropicity to that of orthotropicity and examine the sensitivity of this change for some simple geometries. In addition some necessary relationships between stress and strain for orthotropic materials will be developed. The recent years have seen an increasing interest in the field of rock mechanics. This is amply demonstrated by the number of articles appearing in the technical literature. The majority of these articles use as a basis for analysis the classical linear theory of elasticity. In addition, the assumptions that the material under consideration is elastically homogeneous and isotropic reduce the number of constants necessary to write an analytical relationship between stress and strain to two, e.g., Young's modulus and Poisson's ratio. Most workers in the area of rock mechanics realize that removing the conditions of homogeneity and isotropicity will bring the analysis of stress-strain relationship for geologic materials closer to reality. However, the algebra involved in analysis without imposing these restrictions is usually heavy. It is the purpose of this paper to relax the condition of isotropicity to that of orthotropicity and examine the sensitivity of this change on stress concentration for some simple geometries. In addition, it is shown that the expression for maximum stress concentration for some simple geometries considered can be further simplified if further assumptions are made. The maximum stress concentration, under these additional simplifying assumptions, is shown graphical1y. In the linear theory of elasticity, generalized Hooke's law assumes the following form

Jan 1, 1965