Search Documents

By P. J. Potter

Practically all tin-base babbitt metals used in engine bearings are made to customers' specifications, which are many and varied. The copper ranges from 3 to 8 per cent. and the antimony from 4 to 13 per cent.; generally, the babbitt with lower copper content will contain from 4 to 8 per cent. antimony and that with higher copper will have from 7 to 13 per cent. antimony. The allowable lead content varies from 0.20 to 2.00 per cent. If a solder is used as a bonding material instead of tin, the resulting material in the finished bearing will have a higher lead content, but it would not be enough to bring the lead above specifica-tional limits. Impurities such as iron, arsenic and bismuth should be determined in the tin before using to insure a uniform and high-grade product. These points must be considered when segregating and grading the waste that comes from the finishing operations on lined bearings. Classification of SCRAP Because of the extremely rigid nature of most of the specifications for bearing linings it is necessary to use the purest of materials as a base for all compositions. The problem of handling secondary metals is confined almost entirely to the recovery of drosses, spills and turnings incident to the manufacturing operations. As a matter of convenience the waste or scrap may be divided into 10 grades, as follows: 1. Tin from pots where tinning operation is carried out. 2. Tin and babbitt spatters from babbitting operation. - 3. Tin skimmings combined with burned zinc chloride. 4. Borings and reamings. 5. Gates from die-cast bushings and bearings. 6. Drosses from die-cast pots, babbitt foundry pots, and pots in babbittiug room. 7. Babbitt with small amount of bronze from machining operations. 8. Babbitt and bronze borings. 9. Scrap bronze-back babbitt-lined bearings. I 10. Scrap die-cast bearings and bushings. A few of these grades of salvaged material have compositions that make it possible to determine beforehand where they may be used to

Jan 1, 1930

By O. M. TUPPER

REQUIRING a finer ground clay than that obtainable with a dry pan or hammer mill, the Clay Corporation of California installed a five-roller, low- side Raymond impact mill at its Lincoln plant in 1925 and since then has been economically grinding fire clay with a moisture content as high as 15 per cent. This was one of the first, if not the first, of this type of mill to be used in the grinding of clay on the Pacific coast. The pulverizer consists of a die-ring, lying in a horizontal plane, enclosed in a sheet-iron housing. A vertical shaft supports a spider from which five rolls are suspended in such a way as to always have them bearing on the die-ring. The vertical mill shaft is driven by means of beveled gear and pinion from a horizontal shaft which is connected by belt with a 60-hp. motor with suitable pulleys to give a speed of 175 r.p.m. A large fan which has a speed of 1100 r.p.m. and is belt connected to a 40-hp. motor is connected to the mill housing. The discharge end of the fan is in turn connected to a cyclone dust collector.

Jan 1, 1929

By Peter Greenfield, Paul A. Beck

Thirty binary systems of vanadium and chromium group transition elements with second and third long period transition elements were explored in regard to the intermediate phases formed. It was found that the phases predominating in these systems are s, AB type with ordered a-tungsten or C8 structure, close-packed-hexagonal with small unit cell dimensions and, finally, phases isomorphous with 1-manganese. IN recent years, considerable information has become available concerning the intermediate phases in binary systems of the transition elements. Thus, the s phase has been found to occur in most of the binary systems of vanadium, chromium, and molybdenum with the group of elements manganese, iron, cobalt, and nickel.' It was observed that, while the rr phases formed by chromium with manganese, iron, or cobalt possess a considerable temperature range of stability, particularly in the Cr-Co system, the corresponding s phases with molybdenum are limited to a temperature range of less than 400" above about 1200°C. Goldschmidt' reported v phases of tungsten with iron and cobalt, and these are apparently stable only at (and above?) 1400°C." Exploratory work in this laboratory with Fe-W and Co-W alloys of approximately 60 atomic pct W annealed at 1300°C did not produce X-ray patterns suggesting the presence of a phase. It appears then that the phases of iron and cobalt with the chromium group elements decrease in stability as the two components are chosen from long periods further removed from each other. From the available information, it might be concluded that the controlling factor is the increasing difference in atomic radii between the components. In contrast to the a phase, the phases formed by iron and cobalt with chromium group elements' are stable only when the latter have large atomic radii (molybdenum and tungsten); the corresponding phases with chromium do not occur. When the difference in atomic size becomes still larger (r,/r,, approaching the ideal value of 1.225), the u and p phases are replaced by Laves phases (AB,), as in the alloys of iron and cobalt with columbium," tantalum." and titanium."-" However, atomic size certainly cannot be the sole determining factor, since, for instance, in contrast to the very stable (Mo, Co)p phase, no such phase occurs in the Mo-Ni system even though the atomic diameters of cobalt and nickel are nearly the same. Similarly, chromium and cobalt form a a phase in a wide temperature range," but the corresponding s phase in the Cr-Ni system is missing. It has been shown that the composition of the u phase in various binary and ternary systems of transition elements in the first long period may be correlated in a fairly quantitative manner with the number of electron vacancies. The influence of electronic structure is probably present also in binary and ternary phases' and to some extent, apparently, even in Laves phases." " Although the absence of phases in the Cr-Ni and Mo-Ni systems has not as yet been explained on the basis of electronic structure, it appears reasonable to suspect a connection. One of the great difficulties in arriving at well founded rules in regard to the alloying behavior of transition elements lies in the lack of reliable information concerning the details of their electronic structure in the metallic and alloy form. The theoretical penetration of this field appears to be beset by very considerable difficulties, even when the complications due to alloy formation are disregarded. Another great source of uncertainty is the scarcity of phase diagram information even for binary systems of the transition elements so that only a very limited basis is provided for generalizations as to the occurrence of intermediate phases. For instance, very few binary phase diagrams of second and third long period transition element systems have so far been published. The present work was undertaken in order to survey the various types of intermediate phases occurring in 30 binary systems of elements of the group vanadium, columbium, tantalum, chromium, molybdenum, and tungsten with the elements rhenium, ruthenium, rhodium, palladium, and platinum. For most of these binary systems phase diagrams are very incompletely or not at all known, as will be further reviewed.*

Jan 1, 1957

By R. H. Rice

Turbo blowers for blast-furnace blowing have now been in use for some years, and a review of the experience gained and the present state of progress may be interesting.

Jan 1, 1915

By Donald R. Lessard

I. INTRODUCTION There is no question that the choice of an appropriate discount rate is a critical element in virtually all business decisions in extractive industries. The standard textbook approach relies on a single overall cost of capital for an entire firm, itself a weighted average of the firm's cost of debt and equity. But a single rate is appropriate only if the commercial risks and financing structures are similar for all projects under consideration. In extractive industries, appropriate discount rates are likely to vary greatly from project to project. Risks of projects differ markedly by mineral, by country in which the project is located, by stage in production, and by position in the project's life. Further, for a variety of institutional reasons, financing structures vary greatly in relation to these same variables and thus the discount rate appropriate to the entire investment and, in particular, to the sponsor's equity investment will vary even more markedly. Failure to select discount rates which reflect these differences can result in extremely distorted decisions. Our interest in this subject results from our ongoing research on alternative ownership and financing structures for large scale extractive ventures in less developed countries where risks to the various participants--the sponsors, the financiers, and the host government--vary dramatically with the different options. Given the magnitude of these differences, a single discount rate for all options is clearly inappropriate. However, there appear to be few guidelines for practicing managers to follow in setting appropriate rates. In this paper, we take a first step in this direction.

Jan 1, 1977

By Walter Nummela

This acronym may be readily deciphered, and it represents the programming theme for the SME Sessions at the Centennial Meeting of AIME in New York in 1971. The Concentration Committee thus charged out to grab, to induce, and to accept volunteered papers within that framework. The program for the Concentration sessions is in and hopefully all deadlines will be met as specified in the instructions to authors. Without spelling out what is to be seen and heard in New York, how well did the Committee satisfy the theme described in the title? Perhaps it was by virtue of the international makeup of the Committee (Member Dan Pickett is with the Mines Branch in Ottawa) that an international slate of authors was assured. Four countries are to be represented-Bolivia, Canada, Italy, and the United States.

Jan 1, 1970

By R. C. Palmer

THE testing of flotation oils has occupied a large part of the time of the testing departments of various companies using the flotation process in the beneficiation of their ores. The great differences in ores and iii oils has made such work necessary as it has not been possible to select the oil best suited for the purpose without trial of many kinds. In fact, individual shipments of flotation oils from the same manufacturer will often differ so radically that the mill men have been forced to test every lot of flotation oil before its use in the mills. Further, although almost every imaginable product of the distillation of wood, from alcohol to pitch, has been tested in a more or less perfunctory manner by various people, few companies have allowed the results of their tests to be made public. This work was undertaken for the purpose of obtaining reliable data regarding the value as flotation agents of a number of products that are obtained from the distillation of wood by different methods, and incidentally to determine whether some of the products not used at present could be used. Large quantities of such materials are being wasted or burned in the wood-distillation plants of the United States, and if some use other than fuel could be found for these materials, such a use would represent a distinct saving to the country as a whole, would increase the profit of wood-distilling plants now operating and perhaps make it possible for others to operate which at present cannot do so except at a loss. At the same time it was thought that if such products can be used as flotation agents, then their use would serve to increase the number of oils and other products available for flotation purposes. It was also hoped that it might be possible to discover a substitute for some of the most effective but comparatively high-priced oils which are now used for flotation

Jan 8, 1916

Secretary Membership Committee Increase of Membership Papers and Publications Committee Library Committee Treasurer Report of the Secretary TO THE BOARDOF DIRECTORASN D THE MEMBEROS F THE AMERICANIN STITUTE OF MINING AND METALLURGICAENL GINEERS GENTLEME:N As will be shown by the special reports of the Finance, Membership, Library, Papers and Publications, Increase of Membership, and other standing Committees, together with that of the Treasurer, the year 1927 was one in which the Institute made very satisfactory progress in a number of directions. In total numbers the membership is no larger but in revenue from dues there has been a marked increase. This has been due to the promotion to full membership of Junior Associates of earlier years, to the larger proportion that come in originally as members rather than juniors, and to the keener interest in the work of the Institute reflected in prompter payment of dues. The latter is important, since experience shows that of those who fall behind a large number must ultimately be dropped for non-payment. Conditions in the mining industries have been healthy though not booming. It has been much easier for members to find employment and meet their financial obligations but there has not been that flow of young men into mining, and hence in part into the Institute, that characterized certain earlier years. Rather the tendency toward centralization and larger industrial units has restricted the number, though not the scope, of opportunities for technical men in the mineral industries. The Institute is constantly receiving resignations from members crowded out of mining into other lines of activity. On the other hand, those who remain in mining and metallurgy have a greatly increased necessity for i,dormation and contacts with technology. A few years ago many superintendents and most foremen were non-technical men. Today the reverse rule obtains and shift bosses and men who occupy even lower positions in industrial units are called upon to know and to apply such an amount of technical knowledge that graduate engineers are the rule rather than the exception. The curious situation has obtained that with a much smaller enrolment of students in the schools of mining and metallurgy there has been at times an actual shortage of young engineers for beginners' jobs. The young men retort that the conditions of employment and pay offered in mining are not equal to those in other lines and, while it is undoubtedly true that the young engineer beginning in mining is able to start under conditions markedly better as to pay, living, and responsibility than did the men who are now leaders, they are required to know much more and have usually spent more in time and money to qualify for their jobs. The whole matter is one which warrants much more attention than has been given to it. For the Institute it is important since the young men

Jan 1, 1928

By L. G. Austin, P. T. Luckie, R. R. Klimpel, R. S. C. Rogers

1. INTRODUCTION The Bond method(1.2) for sizing tumbling ball mills has been used successfully for many years. The primary purpose of the Bond calculation is to predict the mill size and mill power to give a desired capacity (Q tph) from a wet overflow ball mill in normal closed circuit operated with a circulation ratio of 2.5. The input to the calculation is the make-up feed size characterized by the 80%-passing size in micrometers (xG), the desired circuit product size characterized by the 80%-passing size (xQ), and an empirical grindability number (the standard Bond Work Index) determined by a standard test. A series of empirical correcting factors(2) are used to convert the results to open-circuit or dry grinding in grate discharge mills. The Bond method has two major engineering advantages: (i) it is very simple; (ii) experience has shown that it works for many circumstances, as a reasonable approximation, because it is based on direct conversion of test data to results measured on industrial mills. There are four main disadvantages of the Bond method. First, there will be a range of error for any specific mill and material and set of operating conditions because the method does not explicitly include several variables which are obviously important: (i) recycle ratio and classifier efficiency (ii) mixture of ball sizes in the mill (iii) variations of residence time distributions with mill geometry and slurry density (iv) lifter design (v) slurry rheology (vi) different underfilling or overfilling of the mill as flow rate is changed. Second, the Bond method explicitly assumes that specific grinding energy E is not a function of ball load, whereas industrial practice and laboratory tests(3) show that the specific grinding energy (to go from a specified feed to a specified product) is less for lower ball loadings than the ball loading for maximum mill capacity. Third, the method uses only the 80% passing size of circuit feed and product to characterize the size distributions, whereas mill capacity in general must depend on the shape of the feed size distribution and the product size distribution. The prime example of this is the use of the reverse closed circuit which removes some fraction of the make-up feed before it is

Jan 1, 1982

By George Krauss, Morris Cohen

NUMEROUS investigators1-4 have shown that one of the most conspicuous effects of the reverse marten-sitic transformation in Fe-Ni alloys is the stabilization of the austenite which forms on reversal. However, the present authors5 found a virtual absence of stabilization in a recent study of this subject. The purpose of this note is to account for the discrepancy.

Jan 1, 1963

By Orville R. Lyons, A. C. Richardson

Operating data is presented for a Bird centrifuge used to dewater coal treated at one preparation plant. The data include: (1 ) percentages of solids in centrifuge feed, cake, and effluent and the plant circulating water for a period of four consecutive operating shifts, and (2) screen-sizing data for a number of centrifuge feed, cake; effluent, and combined cake-effluent samples. An evaluation is included of the relationships between fine solids in the centrifuge feed and the total moisture content of the centrifuge cake.

Jan 3, 1950

GENTLEMEN : It is my privilege to transmit herewith the reports for the calendar year 1932 of your Treasurer and the Chairmen of the following Standing Committees: Finance, Admissions, Membership, Papers and Publications, Library, and Mining and Metallurgy. To these reports you are referred for additional details of the year's activities. Finances.-Continuation of depressed conditions in the mining industry (in common with other industries) caused the income of the Institute to decline from $168,274 in 1931 to $138,331. However, economies were effected so as to reduce expenditures from $171,198 to $135,977. As a consequence the net result of the operations for the year was a-surplus of income amounting to $2,354 compared with a deficit of $2,924 in 1931. This gratifying result is accounted for in large measure by the foresight of the Finance Committee in anticipating a substantial decline in income and preparing the budget accordingly. Incidentally, the tentative budget for 1933 has been balanced at $125,000.

Jan 1, 1932

By J. W. White, J. M. Richardson

Mass balance calculations on industrial grinding circuits are routinely performed during circuit design as well as during post-installation evaluation of operating circuits. Though such routine mass balances are straight- forward, a systematic approach can yield substantial long-term benefits. This chapter presents and evaluates several approaches useful for achieving various circuit design objectives and also considers several methods for reconciliation of data collected around an operating circuit. Numerical examples illustrate the basic concepts and techniques.

Jan 1, 1982

By Nick Barton

Simple methods for estimating the shear strength of rock joints and waste rock are reviewed. For the case of rock joints, the methods are based on a quantitative characterization of the joint roughness and the joint wall strength. Size-effects are found to reduce the peak strength of large joint samples to values below the ultimate or so-called "residual" values measured in the laboratory. Tilt tests and surface profiling on natural size blocks within the jointed rock mass are recommended for obtaining scale-free properties. The joint parameters obtained can be used to model complete strength-displacement-dilation behavior if this level of input is required. Large scale tilt tests can be performed with advantage on both rock joints and waste rock. The behavior of these two materials is surprisingly similar. Both are influenced by the size-effects on the compression strength of the rock, and both have similar log-linear relationships between effective normal stress and the peak drained friction angles. The resulting high values of friction near the toe or close to a slope face in either material can be misleading.

Jan 1, 1983

By Samuel Doak

THE utilization of rotary kilns, of the well-known cement type, for the preparation of iron ores, for the blast furnace, has become of considerable economic importance within the past 10 years in certain localities, notably those where the native ores are lean. Such kilns may be used simply for the agglomeration of ores too fine to be charged into the blast furnace (i.e., ores whose loss in the dust catchers is excessive, and whose fineness is detrimental to the working of the furnace), or for the desulphurization of lump and fine ores the sulphur content of which does not exceed 6 or 7 per cent. The desulphurizing action can be combined with that of agglomeration provided the kiln is sufficiently large. Other processes have been developed for the same purpose, but while I am not able to draw a comparison between them by reason of lack of sufficient data, it is safe to say that the kiln, if properly dimensioned for the character of ore to be treated, will compare favorably in its results, both as to economy and quality of product, with any other process. It is not, however, as well adapted for the treatment of flue dust, as is a sintering operation, on account of the large percentage of fine coke contained therein. Any combustible entering the kiln at its feed end renders the process very much more expensive and unsatisfactory on account of the difficulty of controlling the temperature, also because of the rapidity with which long "rings" form, due to the increased heat at the cooler end of the kiln. The greatest value of the kiln at present is in the treatment of pyrites cinder; that is, the residue from pyrites ore after the extraction of the greater part of the sulphur. This cinder, while high in iron content, has too much sulphur remaining in it to be allowed to form a large part of the blast-furnace burden, without further treatment. It will range in metallic iron from 42 per cent., representing a very low-grade cinder, from a domestic pyrites, to 64 per cent. of the residue from the best Spanish ore, and the corresponding silica content will vary from the maximum of about 25 per cent. to 1 ½ per cent. The residual sulphur depends largely on the type of burner used in the original desulphurization. In general, the leanest original ores retain the greatest amounts of sulphur. In

Jan 9, 1915

By John W. Sweeney

Florida is blessed with some of the worlds greatest phosphate rock deposits, and doubly blessed in that those deposits are uraniferous. Until recently, the uranium con¬tained in phosphate rock had been ignored, but spot mar¬ket prices in the $40-per-pound range have spurred actions which will soon transform the state into a major uranium supplier. In 1978, two plants in Florida and one in Louisiana went it on- stream to recover uranium oxide from phosphoric acid, and construction began on three other extraction facilities. Together, these six plants will be cap¬able of recovering 1940 t/y (2140 stpy) of yellow cake from Florida phosphate in the early 1980s, equivalent to 15% of the projected US requirement. By the year 2000, Florida phosphates will have produced a projected 49 000 tons (54,000 st) of uranium oxide to fuel the nation's nuclear reactors.

Jan 9, 1979

By T. H. Troller

FOR a long time propeller-type fans have been considered a very adequate means to move great quantities of air against small static pres-sures. They have been in use for this purpose in mines, as well as in other installations. For static pressures of over 2 or 3 in. of water, the centrifugal blower almost ruled the field until very recently. Some attempts were made to use a number of propellers in line. Such arrange-ments made it possible to obtain pressures higher than 2 in. of water, but they complicated the construction and increased its expense, and the efficiencies were not improved. The more recent development of propeller-type fans has been decidedly influenced by the intensive aerodynamic research in connection with aeronautical development, which has taught us, in particular, how to use airfoils properly. The characteristic that makes an airfoil so valuable is the fact that when it moves through the air a high force component, the "lift," acts on it vertical to the motion, while the "drag" in the direction of the flow is small. The ratio of lift to drag is approximately 20 to 1 at the angles at which the profile is used in practice. An element of the turning blade, the movement of which, relative to the air, is mainly in the direction of the plane of rotation, thus experiences only a small "drag" FIG. 1.-DIAGRAM OF FORCES ON WING SECTION. opposing its rotation, and for this reason a relatively small torque is required at the driving shaft. At the same time there is a strong force component at 90° to the plane of rotation. This force is parallel to the propeller axis in the direction opposite to that of the flow of air, with a correspondingly high pressure increase.

Jan 1, 1936

By F. W. McQuiston

Teamwork is the key to an efficient organization. Cooperation among mining staff members is an obligation owed to the company. The more cooperation the metallurgist receives from underground, the higher milling yield will be, which in turn makes for a greater mine profit. There is no pay for metal left in mill tailings. The metallurgist is not in a position to be of help to either the geologist or mining engineer, but can receive valuable assistance from both. Therefore, the metallurgist must win underground cooperation. The mining engineer is usually interested in geology because of its relation to ore control; in milling because that is where the rock goes. However, any overlapping of interest between geologist and metallurgist is quite remote.

Jul 1, 1956

By B. L. Averbach

Recovery and primary recrystalliza-tion in cold worked metals are usually considered as two competing processes. Some of the effects which usually accompany recovery are: alleviation of stress corrosion tendencies, changes in thermal emf,1 damping capacity,2 electrical resistivity,2 and magnetic properties,3 and only minor changes in hardness or the related strength properties. During primary recrystalliza-tion new unstrained grains are formed at the expense of the strained matrix. These new grains eventually become visible metallographically, and nucle-ation and growth kinetics have been indicated for this process.4,5 Frequent attempts have been made to study the cold-working phenomenon by observations on the line broadening by X ray diffraction patterns. Relatively few measurements of line intensities have been made, although Brind-ley and his collaborators, 6,7,8 by means of film techniques, compared the intensities of cold worked Cu, Ni, and Rh patterns with those from chemically precipitated powders. These precipitated powders were presumed to be strain free, and it was found that the intensities for the cold-worked materials progressively decreased as the Bragg angle increased except for the first line, where there was an increase due to reduction in extinction. This was interpreted as a randomness in atomic position induced by cold work. Such randomness is similar to that caused by thermal agitation and has been described as "frozen heat" displacement of 0.08-0.10 A from the mean atomic position. In a recent study9 on the effect of cold work in metals on their powder pattern intensities, the changes in integrated intensity for heavily cold worked alpha brass were observed as a function of the annealing temperature. These measurements were made with a manually operated Geiger-counter spectrometer using CuKa radiation monochromated with a rock salt crystal. Intensity measurements were made with a scaling meter over small intervals of angle, and the equipment was so arranged that the diffracted and incident beams made equal angles with the specimen. Intensities could be compared directly by simply interchanging specimens, and comparisons from day to day were made with a standard whose line intensities did not change on aging. It was shown that a cold worked alpha brass standard was stable for at least a year. Table 1 indicates the results of the integrated intensity measurements on a 70 Cu-30 Zn brass. In the sample preparation, a brass plate was first cold rolled 50 pct and then filed, screened to —325 mesh, compacted into briquettes at a pressure of 60,000 psi and finally annealed for one hour at various temperatures up to 400°C. The briquetting pressure did not seem to influence the integrated intensities, and most of the cold work was introduced by the filing. Although this method of cold work is not quantitative, it was used to obtain random orientation (and thus uniform diffraction lines) in order to make accurate measurements of integrated intensity. Back reflection patterns were taken in each case to check the uniformity of the lines, and from the observed line broadening it was apparent that this type of plastic deformation was quite severe. Care was taken to traverse the entire background of the pattern and to assign to each peak the total intensity above this background. The bases of the diffraction lines were quite broad and spread out over several degrees, even for the narrow peaks. The theoretical intensities were calculated to include a temperature correction, a dispersion correction, and a Lorenz- polarization factor corrected for the crystal monochromated beam. In Table 1 it was necessary to match the calculated and observed values at only one point, and the rest of the experimental values were converted directly to this arbitrary scale. The integrated intensities in Table 1 are listed in arbitrary units, and the accuracy was sufficient to reproduce any of the measured line intensities to within + 1.5 units. It is evident that the percentage error on the strongest line (111) was quite low. The calculated values and the observed intensities for the cold worked material matched reasonably well. As the annealing temperature was raised, however, the intensity of the strongest reflections, particularly the (lll), decreased measurably. Since the background intensities of all of these patterns were identical, such behavior could be interpreted as a primary

Jan 1, 1950

By Carle R. Hayward

The growing importance of metallography has caused a corresponding interest in the improvement of apparatus for preparing specimens of metals and alloys for microscopic examination. The purpose of this paper is to describe an electric heating-furnace, a grinding- and polishing-machine, and a device for mounting specimens, which are used in the metallographical work at the Massachusetts Institute of Technology. These three pieces of apparatus were designed and made in the laboratory of the Institute, and each possesses some original features which may be of interest. Electric Heating-Furnace. The accurate control of heat necessary for metallographic work is best obtained by the electric-resistance furnace. Uufortunately, however, even the platinum-wound furnaces cleteriorate with use and ultimately burn out, while the cheaper resistance-materials are often short-lived. Since the resistance-coil must be replaced from time to time, it is of advantage to be able to make this change with as little trouble as possible, and this is an important feature in the furnace shown in Fig. 1. A is a cylindrical galvanized-iron can, with two handles, B. A porcelain tube, C, passes through the central hole in the cover of the can and rests upon the asbestos disk, D; the bottom of the tube is held in place by the asbestos ring, 3. The space, F, around the tube is filled with powdered magnesia. G is an ordinary assay-crucible, with the cover inverted so as to present a smooth top for supporting a second porcelain tube, H. The latter is wound with " Excello " resistance-tape, 0.014

Jan 1, 1912