Search Documents

By C. S. Smith, Chih-Chung Wang

TURNBULL and his collaborators1,2 have developed the theory of homogeneous nucleation as applied, inter alia, to solidification of liquid metals. Vonnegut³ and Turnbull4 have shown that if a liquid metal is subdivided into small droplets a vast majority of them will undercool very considerably before solidification, generally to as low as about 0.8 of the freezing temperature on the absolute scale. The nuclei effective at small degrees of supercooling in bulk metal seem to be internal or surface heterogeneities, relatively small in number. If the metal is subdivided, those droplets that happen to contain such nuclei will solidify at a temperature not greatly below the true freezing point, but only a small part of the whole volume will be affected and the majority of the drops will under-cool to the much lower temperature at which homo- geneous nucleation occurs as a result of fluctuations. It occurred to one of the authors that an appropriate subdivision to give effective freedom from random nuclei is produced during the solidification of many alloys that contain a minor amount of a phase of low melting point, and that one might then expect marked undercooling of the distributed phase. Experimental: The alloys selected for initial study were copper with minor amounts of lead and bismuth, and aluminum with tin. In all these alloys, the major component freezes at a temperature not much below that of the pure metal, and there is little further change in constitution on cooling until the lower melting point constituent freezes in an almost pure state. Cooling curves were taken using the controlled heat flow method permitting approximate specific heats to be obtained. Chromel-alumel thermocouples were used, with the standard emf tables, since extreme precision was not needed. The crucible (3/4 in. id, 5/16 in. wall) was made of B & W K-20 insulating brick. It held about 10 cc of the alloy being investigated. The cooling rate was 2.5" to 2.9°C per min under a controlled temperature difference of 20°. Approximate specific heats were computed from the inverse rate curves together with data from a blank run and from a standard run with a copper cylinder of known heat capacity. The alloys for investigation were made from high-purity metals (99.99+pct) and cast into graphite molds. The castings were machined to fit the crucible and to provide a hole for the inner thermocouple. Cooling curves were taken after heating to a temperature about 50" above the melting point of the minor, lower melting-point, constituent. Results The lead phase in an alloy of copper with 5 pct lead did not undercool more than 3" below the melting point of lead (327°C) either as cast or after annealing to produce a new dispersion of the liquid phase. A copper-zinc-lead alloy with 23.75 pct zinc and 5 pct lead undercooled more but showed no thermal effect below 319°C. A cast alloy of copper with 5 pct bismuth undercooled to 249°C (M.P. bismuth 27l °C), but once solidification started it was completed at the same temperature. This was anticipated, since the bismuth forms a nearly continuous phase between the grains of copper, and a solid crystal nucleated anywhere would rapidly* con- sume the entire network of liquid, unless the physical continuity of the liquid were broken through volume changes, inadequate fluidity, or gas evolution. Similar arguments apply in the case of copper-lead alloys, where the lead-rich liquid forms a network along grain edges, though not grain faces. In both cases there would be a few isolated particles

Jan 1, 1951

By Eugene Grace

IN THE careers of the men to whom I have referred we find typified the development of the chief prob-lems of engineering. The first is to shape and direct the forces of nature and thus to bring the world's resources to add to the comfort and welfare of man-kind. That, in a word, is the problem of production. Engineers have made a supreme contribution to the solution of that problem. But I feel that we have two somewhat newer branches of engineering which must command more and more of our attention. Those are what might be termed commercial and human engineering. Of what value is all our efficiency in pro-duction if we do not distribute efficiently, economically and effectively? And of what value is any of it unless we can add to the happiness and deeper satisfaction of those engaged in industry, as well as those who enjoy its -products? I predict that the outstanding advances in business over the next ten years will be in improved merchan-dising and distributing methods. Herein lies a wide field of opportunity for the engineer. We have briefly reviewed certain qualities of engi-neers who have become successful business executives. Is it possible for us to say that the material success of all these men was due to any one characteristic com-mon to each one of them? Indeed, I venture to assert that there is one quality which, in the last analysis, is determining as to whether any roan shall realize material success in this world of ours. That quality-so notable in the character of each one of the men I have named-is sound judgment. Moments arise in every life when it is necessary to say "yes" or to say "no" to a particular proposition or to a proposed line of action. It is the man who says "yes" at the proper time and "no" at the proper time who, in the final analysis, realizes business success. The ability to do this wisely is the mark of sound judg-ment, which is necessary in a business executive. I have known many business men seemingly slow in their mental processes, possessed apparently, of little imagination and of none of the flair which gives fasci-nation to so many characters, and yet who, when crises come-be they big or be they little-are able so to steer their business courses that they move in the right direction instead of into shallow waters or upon the rocks of trouble.

Jan 4, 1928

S., at Niagara Falls, as an expert chemist. There he was engaged in perfect.ing the various kinds of gases, and while thus employed was gassed several times, which so affected his heart and lungs that he was unable to withstand an attack of the influenza which developed into pneumonia, from which he died at the end of 24 hours. He was a member of St. Luke's Episcopal Church, Lebanon, and belonged to the Ancient Accepted Scottish Rite of Freemasonry, Lebanon Lodge 121, I. 0. 0. F. and Camp 65, P. 0. S. of A. Lieutenant Bernhardt Edward Heine Bernhardt Edward Heine, a lieutenant in the Aviation Service of the U. S. Army, died as the result of a fa1I1 in an aeroplane at Fort Sill, Okla., on Aug. 10, 1918. The accident occurred on Aug. 2, when the machine in which he was flying with Lieutenant Carsons fell from a height of 1500 ft.; Lieutenant Carsons was instantly killed, but Lieutenant Heine died from his injuries a week later. Lieutenant Heine was born at Mount Clemens, Mich., in 1895. After attending the local High School he entered the Michigan College of Mines, and became a Junior Member of the Institute while still a student. He graduated in 1916, with the degree of B. S. In 1914 he served as a transitman for the engineering department of the City of Hancock, Mich. Lieutenant Heine had been in the army since 1916, having been with the 'troops at 'the Mexican border. He had been in the Aviation Section since August, 1917.

Jan 1, 1920

By F. S. Pettit

The oxidation of Ni-3 to 25 wt pd Al alloys has been studied in 0. 1 atm of oxygen at temperatures between 900° and 1300°C. These alloys have been found to oxidize by three different mechanisms which depend on the temperature of- oxidation and the alloy composition. Two of the three mechanisms do not permit a continuous layer of Al,0, to be formed on the alloy surface and the oxidation rates are greater than that for pure nickel. The third mechanism results in the formation of an external A1203 scale and lke oxidation rates are about three orders of magnitude smaller than those for pure nickel. The minimum amount of aluminum required for the formation of external scales of A L,0, has been determined. NICKEL-base alloys are currently the main source of materials for use at elevated temperatures in gas turbine engines. These alloys are usually coated to obtain oxidation resistance. Coatings on nickel-base alloys are frequently formed by reaction of the alloy with aluminum whereby alloyed nickel aluminides are formed. The alloyed nickel aluminides provide protection to the nickel base alloy because external scales of A1203 (alumina) are formed during oxidation and mass transport through A120, is slow in comparison to mass transport through most other oxides. In view of the protective properties of A1203, it is important to know how much aluminum is required in these alloys in order to form external scales of AlzO,. The present paper is concerned with the oxidation kinetics and the oxidation mechanisms of Ni-A1 alloys and the minimum amount of aluminum required in these alloys for the formation of external scales of Alz03. THEORETICAL CONSIDERATIONS When a Ni-A1 alloy is heated in oxygen at elevated temperatures, the following reactions can take place on the surface of the alloy where the oxide phases are assumed to be virtually pure: These oxide phases are in the form of nuclei scattered over the surface of the alloy and, in view of their rapid formation, they need not be in equilibrium with the alloy. As the oxidation process continues, equilibrium between the alloy surface and the oxide phases is approached and the stability of the oxide nuclei is determined by the composition of the alloy at the alloy/oxide interface because of the following reactions: 3NiA1204 + 2A1 (alloy) = 4AlzO3 + 3Ni (alloy) [41 4Ni0 + 2Al (alloy) = NiA120, + 3Ni (alloy) [ 5 1 Application of the mass-action law to Eqs. [4J and [5J yields the following equilibrium conditions for these reactions: where aA1 and aNi are the activities of aluminum and nickel, are the standard free energies of formation of NiO, A1203, and NA1204, respectively, R is the gas constant, and T is the absolute temperature. If the composition of the alloy at the alloy/oxide interface is such that (akl/ahi) is greater than the equilibrium values defined by Eqs. [6] and [7], then Reactions (41 and [5] will go to the right as written. Conversely, if the alloy composition is such that the activity ratio (aLl,/aki) at the alloy/oxide interface is less than the equilibrium values, then Reactions [4] and [5] will proceed to the left. The equilibrium activity ratios in Eqs. [6] and 171 can be calculated since values for the standard free energies of formation of the oxide phases are available. Standard free energies of formation for NiO and A1203 have been tabulated by Elliott and ~leiser.' The standard free energy of formation for NiA1204 can be obtained from the data of Tretjakow and Schmalzried.' The results of these calculations are tabulated in Table I. Table I shows that the following inequality is valid over the temperature interval 900" to 1300°C: (Reaction [5]) (Reaction [4]) « 1and therefore the aluminum activity for these compositions can be taken as equal to the square root of the activity ratios (i.e., aNi = 1). If equilibrium is estab-

Jan 1, 1968

By G. J. Ballmer

Trucks Are Valuable Auxiliary Haulage Units in Rail Pits For: ( I ) Making railroad grades (2) Establishing benches (3) Making new dropcuts

Jan 10, 1951

By B. H. Bergstrom, Will Mitchell, T. G. Kirkland, C. L. Sollenberger

In a previous article' the authors outlined a study I of the variables in rod milling and also reported data from a series of open circuit grinding tests on a massive limestone in a 30-in. x 4-ft end peripheral discharge rod mill. As a second part of the experimental program, an analysis is now presented for the 30-in. x 4-ft overflow rod mill grinding under identical conditions, except that discharge ports on the periphery of the mill shell have been sealed so that the products from the present series overflowed through a 9-in. diam opening in the center of the end plate. A variance analysis has been made of the combined data for the two experiments, and performances of the two mills are compared here. Included in the first report were descriptions of feed preparation, rod mill circuit, instrumentation and controls, and techniques used to evaluate data. Dependent and independent variables were defined, and variance analyses were made to test the relative significance of variables and to establish magnitude of error for the experiment. Significant data were plotted in various combinations, and conclusions were drawn from the graphs. The procedure and analysis in this series of tests follows the first tests and is not repeated.

Oct 1, 1955

PRESIDENT AND DIRECTOR JOHN R. SUMAN HOUSTON, TEXAS PAST PRESIDENTS AND DIRECTORS DONALD B. GILLIES CLEVELAND, OHIO H.- G. MOULTON NEW YORK, N.Y. TREASURER AND DIRECTOR KARL -EILERS SEA CLIFF, N. Y. VICE-PRESIDENTS AND DIRECTORS W. B. HENRY HOUSTON, TEXAS HENRY KRUMB NEW YORK, N. Y. ERIE V. DAVELER , NEW YORK N Y W. M PEIRCE PALMERTON, PA. PAUL D. MERICA NEW YORK, N. Y. LEROY SALSICH DULUTH, MINN.

Jan 1, 1941

By Ihor A. Kunasz

Introduction Lithium minerals occur predominantly in pegmatites which contain mineral assemblages derived from the crystallization of postmagmatic fluids or from the metasomatic action by residual pegmatitic fluids. They have been the traditional sources of raw materials for ceramic and chemical industries. With the discovery of Searles Lake, brines became new sources of lithium. Indeed, the 1960s may well be referred to as the "brine decade" because several brine bodies of significant economic importance were discovered. In the United States, the brines of Clayton Valley, Nevada, are presently exploited by Foote Mineral Co. The brines of the Great Salt Lake of Utah, the Smackover formation, and the Imperial Valley geothermal field, have been defined as important resources of lithium. In South America, new occurrences have been identified in Bolivia and Argentina. At the Salar de Atacama, Chile, new production capacity is scheduled for 1984. Following the termination of the AEC purchase program in 1959, several companies such as Maywood Chemical Co., American Lithium Chemicals, and Quebec Lithium Corp. were forced to close their operations. Nevertheless, with the development of new applications in glass ceramics, air conditioning systems, synthetic rubber, and metallurgy (aluminum potlines), the lithium industry grew steadily, and with the potential application of lithium metal in batteries and nuclear reactors, a healthy growth can be foreseen. New products and new applications are likely to stimulate exploration for expanded, reserves as well as the search for new sources from which lithium could be extracted economically. Geochemistry of Lithium Lithium is the third element in the periodic table. It is the lightest of all the metals, having an atomic weight of 6.938, an ionic radius of 0.68Å and a charge of +1. The geochemistry of lithium has been extensively studied and has been summarized by Rankama and Sahama (1950), Goldschmidt (1937), and Hortsman (1957). The distribution of lithium in igneous rocks is controlled by its size and its charge, and by the (MgO+FeO) / Li2O ratio. In the early stages of crystallization of a magma, that ratio is very large. Consequently, both magnesium and iron are removed by ferromagnesian minerals in preference to lithium which is then concentrated in the residual magma. This results in an enrichment of lithium in silicic rocks and pegmatites (Strock, 1936). Pegmatites are coarse-grained igneous rocks formed by the crystallization of postmagmatic fluids. Minerals within pegmatites may also form by metasomatism (Jahns, 1955). Genetically, the pegmatites are associated with neighboring intrusives. Mineralogically, granitic pegmatites contain feldspar, quartz, and mica as the main constituents and a variety of exotic elements such as lithium, beryllium, tantalum, tin, and cesium, which may or may not occur in economically significant concentrations. Detailed studies by numerous investigators (Cameron et al., 1949, 1954; Hanley et al., 1950; Jahns, 1953, 1955; Page et al., 1953) indicate that pegmatites often exhibit an internal zonal arrangement, with each zone containing a specific suite of minerals. The lithium minerals are usually found in the intermediate zones, and although as many as 13 zones have been recognized by Cameron, et al. (1949), a complete zonal arrangement is rarely found. Zoning of pegmatite bodies has also been observed on a regional basis. The regionally zoned pegmatite sequences exhibit mineral assemblages and complexity according to their re-

Jan 1, 1983

By S. L. Couling, D. J-P. Adenis

i2) twinning in poly crystalline magnesium does not usually occur homogeneously but is concentrated in localized regions or bands inclined at about 45 deg to the stress axis. These bands of twinning are in many ways similar to the Luders bands seen in mild steel alzd Al-Mg alloys. Within a hand the percentage of the volume twinned may approach 100 with no twinning outside the band. Bands are not produced in specimens of grain size a3 x 10-= in. or in samples deformed at temperatures 300°F. Annealing of heavily twinned regions leads to re crystallization textures markedly different from those found in the starting material. The exact preferred orientation appears to depend on the starting grain size, the amount of compres-sive strain and the manner in which it is introduced. MAGNESIUM, with its hexagonal crystal structure, deforms plastically at room temperature by a variety of deformation mechanisms, one of the most important of which is (1012) twinning. In single crystals such twinning occurs on compression parallel to the basal plane or tension perpendicular to it. In wrought polycrystalline magnesium, such as rolled sheet, the preferred orientation is such that almost all the grains have their basal planes nearly parallel to the sheet surface. Therefore, if sheet material is deformed by cold rolling or by tension in the plane of the sheet, deformation of the grains by (1012) twinning is not favored. On the other hand, twins form readily on compression parallel to the plane of the sheet as in a compression test, on the compression side of a bent sample, or at the outer rim of a drawn cup. The first part of this paper deals with the morphology of (1012) twinning in polycrystalline magnesium. Some aspects of this subject were covered by Barrett and ~aller.' Of direct bearing on the work to be reported here are the comments of Jetter' in discussion to Ref. 1. He shows that Mg + 1.5 pct Mn alloy sheet when bent about a transverse axis develops a pattern of transverse bands on the surface of compression. A longitudinal section through the sheet shows that the bands are wedge-shaped and inclined to the rolling direction. The bands were identified as "outcrops of regions in which deformation is localized as the result of the reorientation brought about by (1012) twinning". The second part of the paper treats the recrys-tallization texture of the specimens twinned by compression. Magnesium deformed and then annealed generally recrystallizes with no change in orientation.1'3'4 This statement is true provided that the amount of (1012) twinning occurring during deformation is small. In an isolated observation, Anse15 has shown that, when deformation produces much (1072) twinning, annealing causes new maxima to appear in the pole figure. The second part of the paper elaborates on this point. I) MATERIALS AND PROCEDURES All of the experimental work to be reported was done using the commercial sheet and plate alloy AZ31B (nominal composition: 3 pct Al, 1 pct Zn, 0.4 pct Mn, balance magnesium). This alloy is available commercially in two tempers, -0 (fully annealed) and -H24 (partially annealed), and specimens of both tempers were used in various experiments. The average grain. diameter (AGD) for -0 temper 0.125-in. sheet is about 0.5 x 10- in.; where material of larger grain size was desired, anneals at elevated temperature were used to grow the grains. compression tests were made on a screw-driven "hard" machine. The specimens were clamped in a

Jan 1, 1964

By Carl O. Theime

Industrial specialization has rapidly created a demand for new and better alloys. A more thorough understanding of the requirements of specific industries and the discovery of processes by which it has been made possible to utilize certain metallic elements in larger quantities, together with greater purity in most virgin metals, has resulted in a great increase in the number and variety of alloys. This increase in the number of elements entering into non-ferrous alloy manufacture has increased the contamination in secondary metals, as received by the smelter. In order to successfully refine scrap of a much more complex nature it has been necessary for the smelter to install new equipment and to constantly search for new methods of refining as well as to improve the methods already in use. In some instances it is largely responsible for specialization in the secondary metal industry. It is usually necessary to remove the contaminating impurities in scrap or eliminate to a degree not objectionable, no matter how introduced. In order to know what metals or elements are of an objectionable nature, the smelter must make a study of the effect of single elements and combinations of elements on many of the physical and mechanical properties, such as strength, ductility, color, hardness, casting soundness, etc. The smelter of secondary mctals must be able to utilize scrap materials of all kinds, for, sooner or later, most fabricated metal parts and the waste products formed during the process of manufacture find their way to the smelter. In addition, the smelter, in contracting for salvaged material from the producer, gets some undesirable and unusual materials. The value of secondary metals and the importance of their recovery has increased in recent years and it is no longer sufficient to recover the base metal only, such as copper from copper-bearing material, but it is essential that other elements present be recovered and converted into useful form. This paper will deal not with the smelting and refining or separation of impurities from secondary metals but an attempt will be made to show the increased value of metal scrap when properly segregated and in a less contanlinated condition. There are five principal reasons for contamination in secondary metals: New and unusual alloys, productive methods,

By F. Windolph

There are no hard and fast rules for building tailing dams, and each case has to be analyzed individually because of special conditions encountered at each location. Certain criteria are used for building dams at Climax, Colo., where they must be placed in rather steep mountain valleys on foundations that are practically impermeable. The tailing is relatively coarse, and a coarse fraction stays near the berm where it is deposited, while most of the fines flow with the water to the pool. Thirty years experience has led to certain design for toe dams, decanter lines and towers and tailing dams. A new tailing disposal area, started at Climax in 1958, will ultimately have a height of 495 ft and impound about 300 million tons. The following applies to the construction of this new tailing area.

Jan 11, 1961

By Anthony Folger, Charles E. Straub

Kansas produced 38,150,878 bbl. of oil in 1928 and 40,658,170 bbl. in 1929, thereby retaining its rank as fourth among the oil-producing states of this country. Production for 1928 was less than that for 1927 (Fig. 1) because of a decrease in the number of completions, but the average initial production per well (Table 1) shows an increase due to the completion of wells of comparatively large capacity in the new Valley Center pool of Sedgwick County. This increase in average initial production per well was further augmented during 1929 by completion of additional wells of comparatively large capacity in the Valley Center pool and the new Greenwich pool of Sedgwick County. Production for 1929 exceeded that for 1928 and threatened to exceed all records except that of 1918, however, production was prorated in

Jan 1, 1930

By N. Van Wingen

EFFective sand permeabilities can be ascertained from core analysis if the laboratory data are compensated to allow for the presence of connate or residual water. Such adjustments can be made by applying empirically derived correction factors. Effective sand permeabilities can be estimated also from analytical studies of field depth-pressure measurements. In one method the time rate of pressure build-up after a well is shut in from steady-state flow is required, and in the other the direct measurement of a steady-state rate of flow and the corresponding equilibrium pressure. The results of the investigation discussed in this paper demonstrate that these methods for determining mean effective sand permeabilities can be correlated. Introduction In recent years many investigators have demonstrated the practical value of an accurate knowledge of the physical and dynamical characteristics of reservoir sands containing oil and gas. Of these factors, which serve to completely define a porous medium as a container or carrier of fluids, the dynamical characteristics are of particular interest to the production engineer because they afford a direct measure of the rate at which the oil or gas content of a reservoir will become available. The constant that defines dynamically the porous medium as the carrier of a homogeneous fluid in viscous motion is the "permeability." Coke-analysis Method The generally accepted practice in com-piling permeability data has been to analyze in the laboratory core samples taken in the course of drilling through the productive horizon, and to obtain the mean measure of the productive ability or permeability for the interval open to production by graphical integration of the permeability profile. An average permeability ascertained in this manner, however, is useful to the production engineer only for comparisons of wells drilled in the same horizon, as permeabilities determined in the laboratory are measures of only the ability of a porous medium to transmit a single fluid. As a result of many investigations, it has been shown, however, that under actual reservoir conditions water is coexistent with the petroleum and that its presence greatly reduces the permeability of the sand to oil. Empirical relationships showing the effect of the presence of any immiscible fluid A (such as water) in a porous medium on the permeability of the medium to a fluid B (such as oil) have been established separately by Hassler,1 Dunlap,2 and the writer (Fig. I),3 so that the average specific or dry-core permeability as determined in the laboratory can be corrected to give the true measure of the ability of the horizon penetrated to transmit oil, provided the percentage of pore space occupied by connate water is known accurately.

Jan 1, 1942

By N. Van Wingen

EFFective sand permeabilities can be ascertained from core analysis if the laboratory data are compensated to allow for the presence of connate or residual water. Such adjustments can be made by applying empirically derived correction factors. Effective sand permeabilities can be estimated also from analytical studies of field depth-pressure measurements. In one method the time rate of pressure build-up after a well is shut in from steady-state flow is required, and in the other the direct measurement of a steady-state rate of flow and the corresponding equilibrium pressure. The results of the investigation discussed in this paper demonstrate that these methods for determining mean effective sand permeabilities can be correlated. Introduction In recent years many investigators have demonstrated the practical value of an accurate knowledge of the physical and dynamical characteristics of reservoir sands containing oil and gas. Of these factors, which serve to completely define a porous medium as a container or carrier of fluids, the dynamical characteristics are of particular interest to the production engineer because they afford a direct measure of the rate at which the oil or gas content of a reservoir will become available. The constant that defines dynamically the porous medium as the carrier of a homogeneous fluid in viscous motion is the "permeability." Coke-analysis Method The generally accepted practice in com-piling permeability data has been to analyze in the laboratory core samples taken in the course of drilling through the productive horizon, and to obtain the mean measure of the productive ability or permeability for the interval open to production by graphical integration of the permeability profile. An average permeability ascertained in this manner, however, is useful to the production engineer only for comparisons of wells drilled in the same horizon, as permeabilities determined in the laboratory are measures of only the ability of a porous medium to transmit a single fluid. As a result of many investigations, it has been shown, however, that under actual reservoir conditions water is coexistent with the petroleum and that its presence greatly reduces the permeability of the sand to oil. Empirical relationships showing the effect of the presence of any immiscible fluid A (such as water) in a porous medium on the permeability of the medium to a fluid B (such as oil) have been established separately by Hassler,1 Dunlap,2 and the writer (Fig. I),3 so that the average specific or dry-core permeability as determined in the laboratory can be corrected to give the true measure of the ability of the horizon penetrated to transmit oil, provided the percentage of pore space occupied by connate water is known accurately.

Jan 1, 1942

By T. Airaksinen, R. T. Hukki

A new static pneumatic classifier for the primary separation of the feed material for microclassification is discussed. Pilot plant test results and a novel flowsheet for microclassification at the industrial scale are presented.

Jan 1, 1980

By David B. Reger

The discovery of prolific oil wells in old territory hitherto regarded as doubtful, if not worthless, and the rapid extension of a gas pool opened late in 1938 were the most interesting petroleum features in West Virginia during 1939. Oil activity in general was slow because of crude prices that were still fairly low at the end of the year, although substantially increased above those in January. Fewer oil wells were completed, but the average results were better than in 1938. Fewer gas wells, also, were completed, with greatly lessened average initial production. Many old oil and gas wells were abandoned, so that the total number of active wells has not changed appreciably. The account of operations, as gathered from trade journals and other sources, shows that 561 new wells were drilled, resulting in 101 new oil wells with 2261 bbl. of daily initial production; 366 new gas wells with 602,400,000 cu. ft. of daily open flow; and 94 dry holes. Besides these new wells, 61 old wells were drilled to deeper sands, with 12 bbl. and 13,328,000 cn. ft. of added production. On the new wells the oil average was 22.38 bbl. per well per day; and the gas average was 1,645,900 cu. ft. per well per day; the ratio of dry holes to completions was 16.76 per cent. From an exploratory standpoint one partly discredited oil area was revived by good new production, and another small oil pool may have been opened. Some of the results in gas exploration will require more drilling for true appraisal. It is certain, though, that one very considerable gas field in the sands of Mississippian age has been proved; and there is a probability of six new pools in the Middle Devonian shale. In the Oriskany sand (L. Dev.) the Elk-Poca pool has been extended considerably farther northwest into Jackson County; and farther north in Jackson County two widely separated wells, which may be pool openers, have been successfully completed. On the other hand, several important wildcats in various counties have been dry. Stratigraphically lower, some additional wells have been completed in the Newburg sand (Sil.) and one small producer has been completed in the Clinton sand (Sil.), the importance of which can scarcely be overestimated, because no Clinton production has previously been found in the state, although at least seven wells have been drilled through the sand.

Jan 1, 1940

By David B. Reger

The discovery of prolific oil wells in old territory hitherto regarded as doubtful, if not worthless, and the rapid extension of a gas pool opened late in 1938 were the most interesting petroleum features in West Virginia during 1939. Oil activity in general was slow because of crude prices that were still fairly low at the end of the year, although substantially increased above those in January. Fewer oil wells were completed, but the average results were better than in 1938. Fewer gas wells, also, were completed, with greatly lessened average initial production. Many old oil and gas wells were abandoned, so that the total number of active wells has not changed appreciably. The account of operations, as gathered from trade journals and other sources, shows that 561 new wells were drilled, resulting in 101 new oil wells with 2261 bbl. of daily initial production; 366 new gas wells with 602,400,000 cu. ft. of daily open flow; and 94 dry holes. Besides these new wells, 61 old wells were drilled to deeper sands, with 12 bbl. and 13,328,000 cn. ft. of added production. On the new wells the oil average was 22.38 bbl. per well per day; and the gas average was 1,645,900 cu. ft. per well per day; the ratio of dry holes to completions was 16.76 per cent. From an exploratory standpoint one partly discredited oil area was revived by good new production, and another small oil pool may have been opened. Some of the results in gas exploration will require more drilling for true appraisal. It is certain, though, that one very considerable gas field in the sands of Mississippian age has been proved; and there is a probability of six new pools in the Middle Devonian shale. In the Oriskany sand (L. Dev.) the Elk-Poca pool has been extended considerably farther northwest into Jackson County; and farther north in Jackson County two widely separated wells, which may be pool openers, have been successfully completed. On the other hand, several important wildcats in various counties have been dry. Stratigraphically lower, some additional wells have been completed in the Newburg sand (Sil.) and one small producer has been completed in the Clinton sand (Sil.), the importance of which can scarcely be overestimated, because no Clinton production has previously been found in the state, although at least seven wells have been drilled through the sand.

Jan 1, 1940

THE first session of the Institute was held in the hall of the Washington University, Wednesday evening, May 27th, President Raymond in the chair. After the address of welcome by Hon. Thomas Allen, and the reply of Mr. Raymond, the following names were presented for election as members and associates, duly indorsed by the Council. They were unanimously elected : *Henry Booth, - New York City. *Charles H. Morgan, - Worcester, Mass. *Howard Painter, - West Chester, Pa. *Dr. M. J. Goodfellow, - Eberhardt, White Pine Co., Nevada *Otto Wittelshach, - Eureka, Nevada. *John T. Williams, - New York City. †Charles A. Young, - Philadelphia. *Charles E. Stafford, - Boston, Mass. *Arnold Hague, - Orange, N. J. *Richard Pearcé, - Black Hawk, Colorado. *W. R. Maffet, - Wilkes-Barre, Pa. *Prof. George A. Koenig, - University of Pa., Philadelphia *Prof. R. Nutting, Jr., - Indianapolis, Indiana. *Edwin Mickley, - Hockendauqua, Pa. *G. C. Broadhead, - St. Louis, Mo. *Dr. Adolph Schmidt, - St. Louis, Mo. *Alexander Leonhard, - St. Louis, Mo. *Edward D. Meier, - St. Louis, Mo. *John W. Meier, - St. Louis, Mo. *Prof. Forrest Shepherd, - St. Louis, Mo. *Edward Walsh, - Pilot Knob, Mo. *George Riggs, - St. Louis, Mo. †Col. Chas. B. Parsons, - Cadet, Mo. † W. A. Scott, - Mine La Motte, Mo. *Prof. Paul Schweitzer, - Columbia, Mo. *William E. Guy, - St. Louis, Mo. †William Harris, - St. Louis, Mo. *Henry Black, - Pittsburgh, Pa. †W. Noyes, - New York City. *W. Lorenz, - Philadelphia. †E. A. Whetmore, - New York City. * Members. †Associates.

Jan 1, 1875

By F. Milton Lewis, Edward S. Frohling

The information which is required for' a preliminary feasibility study and the additional information which is required for the final feasibility study on a new mineral deposit are discussed. The preliminary feasibility study is made from very little information and at a minimum cost to the owner. However, the outline for the preliminary report is similar to the one used in the final report. In this manuscript, it is assumed that the results from the preliminary study are favorable and the owner authorizes a final feasibility study by an outside engineering company. The type of organization for completing this final feasibility study is described. The final reports includes all information and data relative to this new mineral deposit. This information is presented so that it may be understood by financial people as well as by technical people.

Jan 1, 1978

By Carl O. Thieme

INDUSTRIAL specialization has rapidly created a demand for new and better alloys. A more thorough understanding of the requirements of specific industries and the discovery of processes by which it has been made possible to utilize certain metallic elements in larger quantities, together with greater purity in most virgin metals, has resulted in a great increase in the number and variety of alloys. This increase in the number of elements entering into non-ferrous alloy manufacture has increased the contamination in secondary metals, as received by the smelter. In order to successfully refine scrap of a much more complex nature it has been necessary for the smelter to install new equipment and to constantly search for new methods of refining as well as to improve the methods already in use. In some instances it is largely responsible for specialization in the secondary metal industry. It is usually necessary to remove the contaminating impurities in scrap or eliminate to a degree not objectionable, no matter how introduced. In order to know what metals or elements are of an objectionable nature, the smelter must make a study of the effect of single elements and combinations of elements on many of the physical and mechanical properties, such as strength, ductility, color, hardness, casting soundness, etc. The smelter of secondary metals must be able to utilize scrap materials of all kinds, for, sooner or later, most fabricated metal parts and the waste products formed during the process of manufacture find their way to the smelter. In addition, the smelter, in contracting for salvaged material from the producer, gets some undesirable and unusual materials. The value of secondary metals and the importance of their recovery has increased in recent years and it is no longer sufficient to recover the base metal only, such as copper from copper-bearing material, but it is essential that other elements present be recovered and converted into useful form. This paper will deal not with the smelting and refining or separation of impurities from secondary metals but an attempt will be made to show the increased value of metal scrap when properly segregated and in a less contaminated condition. There are five principal reasons for contamination in secondary metals: New and unusual alloys, productive methods,

Jan 1, 1928