Search Documents

By H. D. Keiser

Minor industrial minerals included in this chapter are: the alum minerals, bromine, calcium chloride, epsomite and other natural magnesium salts, iodine, meerschaum, quartz, industrial crystals other than quartz, and nonfuel gases (air, helium, carbon dioxide). Alum Minerals The natural alums comprise a group of hydrated double sulfates, the most important of which are potash alum, KAI(S04)2.12H20, the "alum" of popular usage; ammonium alum, (NH4)AI(SO4)2, known mineralogically as tschermigite; and soda alum, NaAI(SO4)2.12H20. Kalinite, KAI(SO4)2.11H20, and mendozite, NaAl(SO4)2, 11H20, are fibrous monoclinic alums, distinct from the isometric species potash alum and soda alum.4 Alunite, KAI3(S04)2(OH)6, also known as alumstone or alum rock, has been used as a raw material in the manufacture of alum since early times. All the natural alums are highly soluble and occur as surface evaporation products in arid regions or in sheltered places. Potash alum, together with the other natural alums, commonly occurs as an efflorescence or crevice filling in argillaceous rocks and brown coals that contain disseminated pyrite or marcasite. The mineral is derived by the action of sulfuric acid, formed during the weathering of the sulfide, upon alkali-rich aluminum silicates. Ammonia alum is found chiefly in lignite or broad-coal beds and bituminous shales. Alunite is most commonly associated with acid volcanic rocks, where the rock has been largely altered and alunite formed owing to the presence of sulfuric acid solutions or vapors. Aluminum sulfate, which for most uses is the essential ingredient of alum, may be found in saline residues resulting from the evaporation of natural water and may be formed by the action of acid waters upon aluminous rocks. A deposit of natural potash alum occurs in an irregular network of veins associated with sulfur in rhyolite in Esmeralda County, Nevada, about 35 miles west of Tonopah and 10 miles north of Silver Peak. Alum was recovered at a plant operated on the property between 1920 and 1923 by crushing the ore to ¾ in., grinding to minus 80-mesh, and counter-current leaching; the resulting alum solution was then filtered and crystallized. Alunite was of much interest during World War I as a source of potash and during World War II as a source of alumina. The wellknown deposits at Tolfa, Italy, are veins in trachyte and have been the basis of alum manufacture there since the middle of the fifteenth century. Pure alunite is insoluble in water and in common acids, but if it is heated to 500°C it loses its water of hydration, and the residue consists largely of anhydrous potash alum, part of which is readily soluble in water or acids. If the heat is increased beyond 500°C, most of the sulfur combined with the alumina is released as oxides and the residue consists of potassium sulfate and alumina. Thus, either potash alum (and aluminum sulfate) or potassium sulfate and alumina may be made. In the

Jan 1, 1960

By W. B. Lilienthal

A considerable saving in time and money has been effected by use of a specially designed stainless steel container for laboratory drilling mud test work. This container involves use of a standard tall-form stainless steel beaker for service in which the mud sample is heated to an elevated temperature and maintained there for protracted periods of time, while undergoing agitation to facilitate mixing of mud components. Agitation is accomplished by rotating the filled containers on motor-driven rollers within an oven. Several porcelain balls are generally placed in the containers to further improve agitation. Soft glass containers (.Mason jars) were used in this service in early work, and were found to be unsuitable for the following reasons: 1. Poor resistance to thermal shock. 2. Containers could withstand only relatively low pressures. 3. Accidental breakage in handling. 4. Chemical deterioration and subsequent mud contamination from reaction of high pH muds with the glass at elevated temperatures. Pyrex containers were also considered, but, inasmuch as they provided improvement only in items 1 and 4 listed above the additional cost was not believed to be justified. A scale drawing of the container is shown in the figure illustrating details in cross-section. A pressed stainless steel lid was fabricated to match the rolled edge of the beaker

Jan 1, 1950

POSITIONS VACANT No. 228. Slate mining company desires men for the following positions: Superintendent to take full charge of underground work, quarrying and milling. Assistant or night superintendent. . Foreman for sinking a new shaft. No. 229. Chief engineer to take charge of drafting room, on furnaces and combustion apparatus. ENGINEERS AVAILABLE (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) Mining engineer and executive. Member. Columbia graduate. Age, 32. Married. 9 years' responsible work in mine examination and development. Experience in United States, Canada, Mexico and South America. Now superintendent large operating mine. Personal interview in New York. Available in August. No. 367.

Jan 8, 1917

By D. E. Norquist, J. E. Moeller

The results of wear on marked balls, 4, 31/2, 3, and 2 in. diam are given. All balls were forged steel of practically the same chemical analysis and hardness. The results indicate that balls in a given mill for a given length of time will have equal diameter losses, regardless of size.

Jan 6, 1950

By J. P. Heller, H. B. Bradley, A. S. Odeh

A potentiometric model technique is presented for determining the areal sweep efficiency of a five-spot well pattern, at and beyond breakthrough. A sharp interface between displaced and displacing fluids is assumed. Although the prototype svstem is referred to as a waterflood operation, obvious changes in the notation and computations will adapt the results to other displacement processes. The results of the study include the following. 1. Areal sweep efficiencies for a five-spot well pattern, at and beyond breakthrough, for mobility ratios (displacing to displaced fluid) of 4:1, 2:1, 1:1 and 1:4. 2. Extension of potentiometric analysis to the investigation of the areal sweep efficiency beyond breakthrough in a five-spot pattern by the application of conformal mapping and conductive-solid models. 3. The use of layers of conductive fabric in representing mobility ratio changes in potentiometric models. 4. The development of a probe mechanism for probing conductive solids. The results obtained by conductive-cloth models agree with earlier areal sweep efficiencies at breakthrough obtained by Aronofsky and Ramey 1 on the potentiometric analyzer using electrolytic-tank models. Results beyond breakthrough differ from those obtained by the X-Ray Shadowgraph technique. Data from this study show that, for mobility ratios greater than one, water cut rises rapidly as fluid is produced after breakthrough. However, for mobility ratios smaller than one, a large increase in area swept resulted with only a small increase in water cut. INTRODUCTION In calculating reservoir performance of waterflood-ing operations and other fluid-injection programs, it is necesssary to estimate the areal sweep efficiency * before and after injected-fluid breakthrough into production wells. Influence of mobility ratio on oil-production history, before and after breakthrough for a five-spot well pattern, has been studied by X-Ray Shadowgraph techniques 2-5 and by gelatin models.6 In none of these investigations was the transition zone controlled experimentally. Steady-state anaiog techniques assume that a vertical and discrete interface exists between the displacing and displaced phase. Thus, when using a potentiometric analysis, it is assumed that no transition zone exists. To determine the areal sweep efficiency beyond breakthrough for a five-spot well pattern using the potentiometric analyzer, four principal problems had to be resolved. These were the following. 1. The laborious method of representing changes in mobility ratio in electrolytic tanks by means of contoured wooden blocks. 2. Vapcrization of the electrolyte solution during the study causing concentration changes and, thereby, variable conductivity. 3. The scale-limitation problem 7 that is accentuated by abrupt eiectrolyte depth changes. 4. A wellbore geometry problem. EXPERIhlENTAL EQUIPMENT AND PROCEDURES CONDUCTIVE-SOLID MODEL The theory, equipment and procedural techniques of the electrolytic-tank potentiometric model have been treaced excellently by Lee8 and by Muskat.9 By the use of a conductive solid to represent the fluid conductivity of the porous media, the need for contouring wooden blocks to represent mobility ratio was eliminated. It was found that a carbon-black coated fabric, Uskon D-16,** could be employed as a fairly uniform conductive media. This material, when stacked in appropriate layers and pressed together, can be used to represent changes in mo-

The papers discussed in the following pages were presented during two sessions of the Geophysics Education Committee of the Mineral Industry Education Division on Feb. 17 and 18, 1941. At the first meeting, to consider the "Influence of Geophysics upon Geology Curricula," this Committee was joined by the Geophysics and Mining Geology Committees of the A.I.M.E., the Society of Economic Geologists, representatives of the American Geophysical Union, and delegates from the Committees on College Curricula and on Applications of Geology of the American Association of Petroleum Geologists. Quentin D. Singewald and Sherwin F. Kelly presided. At the ensuing session, especially emphasizing the integration of geology, physics and chemistry for the solution of earth problems, the joint participants with the Geophysics Education Committee were the Geophysics Committee, and representatives of the American Geophysical Union and of the Committee on College Curricula of the American Association of Petroleum Geologists. Richard M. Field and W. R. Chedsey presided. In the following summary of the discussion at the two meetings, written discussion submitted subsequently is not differentiated from that offered orally at the session. A provisional report of the Geophysics Education Committee was presented at the second session, and some of the following discussion refers to it. This report has not been printed (it is anticipated that a more comprehensive, final one will be rendered at the 1942 annual meeting). A few mimeographed copies of this provisional report were made. Dr. W. P. Haynes presented some notes prepared by Dr. F. H. Lahee, Chairman of the American Association of Petroleum Geologists' Committee on College Curricula. This Com- mittee's inquiries reveal the general opinion that a four-year academic preparation is inadequate, five or six being advisable. The fundamentals, mathematics, physics, chemistry, and English composition, should be stressed in the first three years, with specialization in the last two or three years. Some companies provide an apprenticeship period, and themselves give additional training. During academic years more attention needs to be given to engineering training, to field mapping, and in geology to stratigraphy and sedimentation. The amount of mere memory work should be cut, and men trained to observe and reason. Dr. Lahee emphasized the need of more adequate preparation in English composition, because of the inability of many graduates to compose acceptable reports. Sherwin F. Kelly pointed out that much time in university training, which ought to be devoted to technical subjects, was taken .up with English courses. He emphasized that it is the part of the universities to demand of the high schools that the students they send to the university be properly trained to speak and write English. Prof. W. T. Thom protested against the crowding of high-school material into already overcrowded college curricula. C. E. Dobbin, chairman of the Committee on Applications of Geology of the American Association of Petroleum Geologists, described briefly the work of his committee in publicizing geology, and said that it found a widespread popular interest in the subject but a lack of appreciation of its importance. He recommended that attempts to coordinate the works of geologists and geophysicists be expanded somewhat toward the further developing and encouraging of a "species of geopolitician" capable of assisting the progress of geology and geophysics by more vigorous advertising of

Jan 1, 1946

The papers discussed in the following pages were presented during two sessions of the Geophysics Education Committee of the Mineral Industry Education Division on Feb. 17 and 18, 1941. At the first meeting, to consider the "Influence of Geophysics upon Geology Curricula," this Committee was joined by the Geophysics and Mining Geology Committees of the A.I.M.E., the Society of Economic Geologists, representatives of the American Geophysical Union, and delegates from the Committees on College Curricula and on Applications of Geology of the American Association of Petroleum Geologists. Quentin D. Singewald and Sherwin F. Kelly presided. At the ensuing session, especially emphasizing the integration of geology, physics and chemistry for the solution of earth problems, the joint participants with the Geophysics Education Committee were the Geophysics Committee, and representatives of the American Geophysical Union and of the Committee on College Curricula of the American Association of Petroleum Geologists. Richard M. Field and W. R. Chedsey presided. In the following summary of the discussion at the two meetings, written discussion submitted subsequently is not differentiated from that offered orally at the session. A provisional report of the Geophysics Education Committee was presented at the second session, and some of the following discussion refers to it. This report has not been printed (it is anticipated that a more comprehensive, final one will be rendered at the 1942 annual meeting). A few mimeographed copies of this provisional report were made. Dr. W. P. Haynes presented some notes prepared by Dr. F. H. Lahee, Chairman of the American Association of Petroleum Geologists' Committee on College Curricula. This Com- mittee's inquiries reveal the general opinion that a four-year academic preparation is inadequate, five or six being advisable. The fundamentals, mathematics, physics, chemistry, and English composition, should be stressed in the first three years, with specialization in the last two or three years. Some companies provide an apprenticeship period, and themselves give additional training. During academic years more attention needs to be given to engineering training, to field mapping, and in geology to stratigraphy and sedimentation. The amount of mere memory work should be cut, and men trained to observe and reason. Dr. Lahee emphasized the need of more adequate preparation in English composition, because of the inability of many graduates to compose acceptable reports. Sherwin F. Kelly pointed out that much time in university training, which ought to be devoted to technical subjects, was taken .up with English courses. He emphasized that it is the part of the universities to demand of the high schools that the students they send to the university be properly trained to speak and write English. Prof. W. T. Thom protested against the crowding of high-school material into already overcrowded college curricula. C. E. Dobbin, chairman of the Committee on Applications of Geology of the American Association of Petroleum Geologists, described briefly the work of his committee in publicizing geology, and said that it found a widespread popular interest in the subject but a lack of appreciation of its importance. He recommended that attempts to coordinate the works of geologists and geophysicists be expanded somewhat toward the further developing and encouraging of a "species of geopolitician" capable of assisting the progress of geology and geophysics by more vigorous advertising of

Jan 1, 1946

By Jerry R. Johanson

The practical application of rolling theory to the design of roll presses is reviewed along with aspects of plant operations which must be considered to produce the required product economically. Appropriate parameters to scale up from laboratory tests to full- scale press operation and improvements possible in existing operations are discussed.

Jan 1, 1977

SECTION I PAGE PAGE Bulletin Wanted v Northwest Mining Convention St. Louis Meeting v (Columbia Section) xvi Proceedings of the Meeting of Affiliated Student Societies... xvii the Board of Directors vii Harrison W. Craver, New Li-¬ John Fritz Medal viii brary Director xviii Herbert C. Hoover, Food. Con Library xx troller viii Pamphlets for Sale xxii President's Prize ix Membership xxxvi Emmons Memorial Fellowship. x Biographical Notice of Her¬ Meetings of Various Societies. x Mann A: Keller : lviii Personal xi Institute Committees lix Employment xii Officers and Directors lxvi Local Section News xiii

Jan 5, 1917

By H. H. Reamer, B. H. Sage

The formation volume and the relative volume of the liquid Phase of mixtures of Condensate and gas from five different parts of a field in the Louisiana area have been established experimentally. These studies included gas-condensate ratios as high as 25.000 cu ft/bbl at pressures up to 5,000 psi. The gravities of the tank condensates were between 53.9° and 63.9° API. The compositions of the condensate and gas samples inves-ligated are presented in tabular form. The formation volume. the relative volume of the liquid phase. and the specific volume of the mixtures are available. A rough correlation of the formation volume as a function of pressure. temperature, and gas-condensate ratio has been presented. This correlation i-considered applicable only to the range of conditions covered in this investigation for systems of similar nature and com-position. INTRODUCTION Often a knowledge of the influence of temperature. Pres sure, and relative quantities of condensate and gas upon the volumetric behavior of fluid*. from a given field has been employed in estimating the Conditions existing in the reservoir. The early work of Beecher and Parkhurst' and the more rrcent Studies of the Dominguez' and San Joaqnin Valley Field;: are examples of experimental studies of this character. Correlation of the volumetric behavior of naturally occurring hydrocarbon mixtures has Proved To be feasible' . at low gas-conden-sate ratios-; for fluids*. from a single geographic area. Progres 5 is being made in the Prediction of the volumetric behavior of distillate systems at high gas-condensate ratios and pressure.. However. the estimation of the retrograde". ' dew-point pressure still remains uncertain and probably can best be established by experiment. For this reason it appears of interest to make available experimental information about the volumetric behavior of mixtures of condensate and gas from five different part.; of a single field. This material shows a rough similarity to data for mixtures of condensate and gas from San Joaqnin ' Valley Fields. In the present paper. 110 attempt has been made to coordinate the available information on tbe volumetric behavior of fluids from condensate fields. It appears hopeful that progress can be realized by the utilization of recently developed equa-tions of state.!' However. the primary problem in any such correlation is the proper identification of the components and constituents of naturally occuring systems. Additional experimental information may be required to permit the determination of the values of the constants of the equation of state for References given at end of paper. Manuscriptt received in the office of the Petroleum Branch June 11. 1951. *For present purposes low gas- condensate ratios will he considered as those below 3,000 cu ft/bbl, and the region of high gas-condensate ratio will be limited to compositions containing more than 5,000 cu ft of pas per bbl of condensate. Mixtures Containing between 3,000 and 5.000 CII ft OF gas per bbl will be considered of intermediate gas-condensate ratio.

Jan 1, 1952

Council PRESIDENT OF THE COUNCIL. JOHN HAYS HAMMOND NEW YORK, N. Y. (Term expires February, 1908 ) VICE-PRESIDENTS OF THE COUNCIL. HENRY M. HOWE NEW YORK, N. Y. J. B. GRANT DENVER, COLO. JAMES D. HAGUE NEW YORK, N. Y. (Term expires February, 1908.) SAMUEL B. CHRISTY BERKELEY, CAL. JOHN A. CHURCH NEW YORK, N. Y. PERSIFOR FRAZER PHILADELPHIA, PA. (Term expires February, 1909 )

Jan 1, 1910

PRESIDENT Willis McGerald Peirce New York City, N Y PAST PRESIDENTS D H McLaughhn, San Francisco, Calif L E Young', Pittsburgh, Pa VICE-PRESIDENTS A. B. Kinzell, New York, N Y H. W Thomas Ray, Arizona Philip Kraft, New York, N Y J L Gillsan Wilmington, Del M. L Haider, Toronto, Ont , Canada VICE-PRESIDENT and TREASURER Andrew Fletcher, New York, N Y

Jan 1, 1951

By M. E. Wadsworth, R. L. Pearson

THE dissolution of UO, in carbonate solutions can occur only il the tetravalent uranium is oxidized to the hexavalent state. The carbonate system is of particular interest because it provides a means whereby the oxidized uranium may be dissolved by forming the complex ion UO,(CO3)3-1. In the presence of oxygen the over-all reaction may be written UO+1/2O,4CO3T+2HCO2UO,(CO4)11+H2O [1] UO, was used in this study because it could be obtained in high purity and also because it is representative of the most refractory of the primary uranium minerals. The mineral ulrichite is the natural counterpart of the synthetic UO, used. The kinetics of the leaching of UO, should be similar for any of the uraninite type minerals. A pressurized system was used not with the hope it could be extended to commercial systems as a primary purpose but simply to provide the means whereby important temperature and pressure parameters could be varied for the evaluation of the kinetic processes. The importance of such pres-

Jan 1, 1959

By O. M. McRae. Discussion by R. W. Jones

R. W. Jones (Senior Exploration Geologist, Standard Oil Co. of California, Box 250, Seattle, Wash.) -Mr. McRae6 and his colleagues are to be congratulated for providing a more coherent structural synthesis of the complex structure in the Courtland-Gleeson area, Cochise County, Arizona, than the "gigantic thrust breccia" concept of Gilluly. 4 However, a few problems of interpretation remain. It is the intent of this note to point out some of these problems, and, drawing on my own work in the area as well as the work of McRae6 and Gilluly, 4 to suggest some interpretations which differ from those previously published. GRAVITY SLIDES In an unpublished manuscript (Jones5) I previously argued that most of the complex structures in the Courtland-Gleeson area can be most reasonably interpreted in terms of gravity sliding caused by uplift and eastward tilting of Jurassic intrusives and associated Paleozoic rocks. Although the field work and drill hole data described by McRae6 provided excellent documentation for two important gravity slides, McRae6 interpreted the basic structure in the Courtland-Gleeson area in terms of major eastward directed thrusting. I continue to disbelieve the

Jan 1, 1967

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who registered at Institute headquarters during the period Sept. 10 to Oct. 10, 1914: James D. Mooney, Akron, Ohio. J. Kojima, Ashio Copper Mine, Japan. Bernard A. Wilkinson, Guadalajara, H. Starkweather, Cripple Creek, Colo. Mexico. S. S. Langley, New York, N. Y. A. B. Parsons, Candor, N. C.. J. H. Warder, Chicago, Ill. Arthur Feust, Santo Domingo, Nicaragua. Lloyd T. Buell, Butte, Mont. G. B. Marshall, New York, N. Y. George R. Rogers, Gowganda, Canada. Henry Krumb, Salt Lake City, Utah. H. 0. Hammond, Douglas, Ariz. Herbert S. Kohlberg, El Paso, Texas. Percy E. Hohne, El Oro, Mexico. Wilbur L. Cross, Jr., Glen Carbon, Pa. Percy E. Barbour, Candor, N. C. Thomas H. Leggett, formerly-in charge of the mining interests of the American Smelting & Refining Co., has resumed practice as consulting engineer with offices in the Singer Building, New York, N. Y.

Jan 11, 1914

By B. C. Wonsiewicz, W. W. Wilkening

Following a procedure proposed by Wheeler and Ireland, Plane stress yield loci were constructed from Knoob hardness numbers. Basically, six differently oriented hardness measurements were made on three orthogml surfaces through pure poly crystalline magnesium sheet, a magnesium single crystal, and sheet of the magnesium alloys: Mg + 0.5 pct Th, Mg + 4 pct Li, AZ31B, and EKOO. Hardness loci were found to be in poor agreement at small strains (E < 0.05) with loci established by a more rigorous technique. At larger strains (E - 0.10) the agreement is fair, but at this stage in deformation the conventional locus has lost much of the asymmetry that characterizes these anisotropic materials. Two effects which will lead to distortions in the Khn locus are discussed with reference to the geometry of plastic flow during a hardness test. DETERMINING a material&apos;s resistance to multiaxial loading is of interest not only from a structural design viewpoint but also from that of deformation processing. Unfortunately, the determination of the yield locus, although simple in principle, involves tedious procedures if the results are to be at all rigorous.&apos; The idea, first proposed by Wheeler and 1reland2 of determining the yield locus by means of six Knoop hardness impressions along the principal directions in a material has obvious appeal. It is simple, quick, and should be applicable to very thin sheets. If such a technique could be demonstrated to produce consistently reliable results, it would be of interest to both researcher and designer. Lee, Jabara, and ackofen have compared the yield locus determined by Knoop hardness measurements (the Khn locus) to a locus determined by more rigorous techniques. They found good agreement for two titanium alloys at a plastic strain of about 1 pct. The purpose of this paper is to investigate if the Khn locus construction is a reasonable approximation to the locus of a highly anisotropic material. Examples of such materials are magnesium and magnesium alloys which have severely distorted yield loci which in turn reflect markedly dfferent yield strength in different directions.&apos; In pure magnesium, for example, the yield stress in tension along the transverse direction may be four times the yield stress in compression in the same direction and twice the tensile yield stress in the rolling direction. Predicting such large differences ought to serve as a severe test of the Khn locus construction. EXPERIMENTAL PROCEDURES Samples of rolled sheet, 0.250 in. (6.35 mm) thick, of pure magnesium and four magnesium alloys (Mg experimental materials. The pure magnesium together with the lithium and thorium alloys were those used in the study of Kelley and Hosford. The grain size was ASTM number 4 for the pure magnesium and number 6 for the alloys. HARDNESS TESTING The materials were sectioned along the rolling and transverse planes, mounted in a quick setting resin, and mechanically polished. Most of the hardness tests were performed on a surface prepared by electro-polishing (30 pct nitric acid in methanol at 0°C and 20 v) with the exception of the AZ31B and EK00 alloys which were made directly on a metallographically polished surface. However, subsequent hardness tests on the same sample after heavily electropolishing, revealed essentially the same hardness as before. At least twenty Knoop hardness impressions under a 100-g load were made in each of the six orientations shown in Fig. 1. The average hardness number and standard deviation were then calculated for each orientation. CONVENTIONAL LOCUS CONSTRUCTION Yield loci were constructed using a technique described in detail by Lee and ackofen,&apos; in which the flow stress (stress at a given plastic strain) fixes the coordinates of a point on the locus and measurements of the strain ratio serve to establish the slope of the locus at that point. The loading paths which correspond to uniaxial tension or compression tests establish the four intercepts of the locus with the coordinate axes plus one point on the balanced biaxial tension line Tensile testing was performed along the rolling and transverse (r, t) directions. Samples had a uniform rectangular gage length 1 by 4 by 4 in. (25.4 by 6.35 by 6.35 mm) and were deformed at a strain rate of 3.33 x 104 sec-&apos;. The tests were interrupted periodically to unload the sample and measure the plastic strains by means of X-Y post yield strain gages. Compression tests in the rolling, transverse, and through-thickness (r, f, z) directions were performed on 1/4 in. (6.35 mm) cubes at an initial strain rate of 8.33 x sec-&apos;. Lubrication was provided by 0.002 in. (51 pm) Teflon sheet which was renewed after unloading for micrometer measurements used to calculate the strains.

Jan 1, 1970

By Svend Rordam

THE development of a cement that will resist the destructive action of sea water and other corrosive waters is a problem that has occupied cement chemists for the past one hundred years. It has been found that of the various salts that commonly occur in corrosive waters, sodium sulphate, magnesium sulphate and magnesium chloride are most destruc-tive to cement. Many investigations have been carried out in the United States, in Canada, and in Europe to solve the problem of what constitutes a sulphate-resistant cement, and during the past 10 years some of the findings give definite information in this respect. COMPOSITION OF CEMENT Portland cement is composed of four major compounds: 1. Tricalcium silicate 3CaO.Si02 (C3S) 2. Dicalcium silicate 2CaO.Si02 (C2S) 3. Tricalcium aluminate 3CaO.Al203 (C3A) 4. Tetracalcium aluminoferrite 4CaO.Al203.Fe203 (C4AF) The two calcium silicates are the main contributors of strength. The tricalcium aluminate contributes some to the early strength of the cement but has the least resistance of the four compounds toward the attack of sulphate waters. The tetracalcium aluminoferrite does not contribute very much to the strength, but is far more resistant to sulphate waters than the tricalcium aluminate. When hardened cement is exposed to water containing sodium or magnesium sulphates, these salts will react with the hydrated tricalcium aluminate in the cement and form compounds that will cause a swelling, disruption and crumbling of the hardened cement.

Jan 1, 1939

By J. K. Edgar

For a number of years the production and use of super-purity aluminum (better than 99.99 pct) has been steadily increasing. High-grade lots of. such aluminum show certain outstanding characteristics not found in lower grades containing principally silicon, iron and copper as impurities. One such characteristic is the so-called "self annealing," that is, the re-crystallization of the heavily cold worked metal at room temperature.&apos; Interest therefore is aroused as to the effects of the impurities. It is well known that the amounts of silicon and copper which occur in aluminum of better than 99.95 pct are completely soluble, at least at elevated temperatures (above 200°C). Iron, on the other hand, is known to be fairly insoluble in solid aluminum. Thus, a knowledge of the limits of this solubility would he of considerable use in studying the characteristics of the high purity metal. All investigators have agreed that iron has very low solubility in solid aluminum. Rosenhain, Archbutt and Hanson2 reported traces of an aluminum-iron phase in the "purest samples of aluminum obtainable." Gwyer and Phillips3 reported that an iron constituent was visible under the microscope in metal containing ".0088 per cent iron." Roth4 found that in the solid state the solubility of iron in high purity aluminum was 0.01, 0.01, 0.017 and 0.022 pct at 225, 320, 500 and 600°C respectively. Dix5 working with alloys containing less than 0.03 pct impurities, concluded from microscopic and chemical analyses of eutectic areas that the eutectic composition was close to 1.7 pct iron. Dix placed the eutectic temperature at 65s°C. Archer and Fink,6 using high purity aluminum-iron alloys, found that the hypoeutectic liquidus intersects the eutec-tic horizontal at 1.7 pct. This is in fair agreement with the investigation of the aluminum-iron system by Gwyer and Phillips who placed the eutectic at 1.89 pct iron with a freezing point of 653&apos;C. Preparation and Chemical Analysis oP Alloys Electrolytically refined aluminum (99.991 pct aluminum) and a high purity alumi-num-iron alloy (11.45 Pet iron) were used in the preparation of the alloys for this investigation. To aid in controlling the iron content of the experimental alloys, an alloy of lower iron content was prepared first from these materials. The high purity aluminum was melted and heated to about 700°C in a plumbago crucible coated with alundum cement and the aluminum-iron alloy was then added. The alloy was thoroughly stirred, fluxed and skimmed and then chill-cast into notch bars. The aIlalyses of the three materials are given in Table I. The alloys for the determination of the solid solubility of iron in aluminum were prepared by melting 600 g total of the aluminum plus the required quantity of the aluminum-iron alloy (No. 92531). These

Jan 1, 1949

By J. J. Gilman, T. A. Read

S URFACE effects in the cleavage of brittle crystals have been known for some oftime,1, 2 but our knowledge of surface effects in the plastic deformation of crystals is of relatively recent origin. In 1936, Roscoe9 eported his observations comparing oxidized and clean cadmium crystals. He found that cadmium crystals 1/2 mm in diam when covered by an oxide film less than 1200 atoms thick had critical shear stresses about twice those for clean crystals. This effect is anomalous in that it cannot be caused by the inherent shear strength of a normal oxide film. Either an interaction between the film and the crystal causes the large increase in strength, or the oxide film has an abnormal mechanical strength. Several authors since Roscoe have studied surface effects in crystal plasticity. A complete review of the literature will not be presented, but most of the results may be summarized as follows: 1—The critical shear stress for slip is increased markedly by very thin oxide films on zinc4 and cadmium crystals;" &apos; also, the entire stress-strain curve is raised by an oxide coating;3,4 both effects increase with decreasing specimen radius. 2—Surface active substances such as oleic acid destroy the hardening effect of oxide films.4, 6-8 The time required for the reduction of the hardening effect to begin increases with the viscosity of the solvent4~ 3—There has been dispute in recent years about the effects of surface active substances themselves on plastic deformation. Rehbinder, Lichtmann, and Maslenikov9 state that surface active substances reduce the strength of metal monocrystals markedly and increase the number of slip lines per unit length at a given strain. The effect varies with orientation for tin crystals being smallest for x, = 0, largest for x, = 45", and intermediate as x, + 90°.10 Several workers claim to have disproved the results of Rehbinder&apos;)"." but Rehbinder and Lichtmann9 have defended themselves and Masing with his collaborators" has confirmed some of Rehbinder&apos;s results. 4—Immersion of metal specimens in electrolytes such as sodium chloride reduces their strength12,13&apos; and subsequent cathodic polarization increases the strength reduction. For noble metals, the strength reduction occurs for both anodic and cathodic polarization," increasing with increasing polarizing voltage. 5—Electroplated copper coatings effect the creep rates of zinc monocrystals. Poly crystals are not affected." 6—Immersion in dilute acid destroys the hardening effect of an hydroxide film. When an acid solution is applied to a steadily creeping crystal, the creep rate jumps to a very high value and then drops gradually to a steady value which is higher than the initial steady rate.*&apos; " If the hydroxide film to be removed is very thin (about 100A thick), the creep rate does not change measurably, but a small rapid strain-increment is observed when dilute acid is applied." 7—Crystal plasticity depends on specimen dimensions. This was observed by Lichtmann and Ven-stroml" for monocrystalline tin and by Andrade and Kennedy" for polycrystalline lead. 8—Immerson of copper crystals in mercury has no effect on their stress-strain curves.&apos;" 9—Bombardment of creeping cadmium crystals with a particles which penetrate the surface to only 0.005 mm may increase their creep rates as much as five times.&apos;&apos;&apos; The experiments which will be described in this paper pertain to: (a) the effect of a crystal&apos;s shape on its plastic deformation, and (b) the effect of metallic surface films on plastic deformation. For the work pertaining to (a), crystals of zinc, tin, and lead were grown which had various shapes. These were tested in simple tension. Macroscopic rotations about the tension axis which are unpredicted by the classical theory of slip were observed, and serrated edges were observed in tin crystals. For the work pertaining to (b), the effects of evaporated and electrodeposited films of copper, nickel, gold, and zinc on the mechanical properties of zinc, tin, and lead crystals were determined. The films influenced both slip and twinning of the crystals in creep and tensile tests. Experimental Details Chemically pure zinc, tin, and lead were used in this investigation. The zinc was 99.999t pct pure;

Jan 1, 1953

By R. F. Campbell, R. F. Miller

SIXTEEN steels containing different combinations of chromium and molybdenum, in amounts up to 5 per cent of each element, were examined for microstructure and hardness after air cooling and after furnace cooling from suitable austenitizing temper- [ ] atures. Diagrams summarizing the structures and hardness resulting from these two cooling rates are presented (Figs. 3, 4, 7).† Data were also obtained on the influence of these two elements, individually and in combination, on the depth 0f decarburization observed after furnace cooling (Fig. 8). COMPOSITION OF MATERIAL The chemical composition of the steels investigated is given in Table I. The plain carbon steel was made in a 25-ton Heroult electric-arc furnace, while the alloy steels were made in a 4.5-ton Ajax-Northrup elec- [ ] tric induction furnace. The cast ingots were hot-rolled to I.75-in. bars. AIR-COOLED SERIES The I.75-in. bars were forged to flat plates, 0.25 in. thick, from which specimens 0.5 in. wide by 2 in. long were cut. The specimens were pretreated to improve their homogeneity by heating to I830°F. (1000°C.) for 20 min. and oil quenching. They were then reheated to I740°F. (950°C.) for one hour and air-cooled, after

Jan 1, 1941