Search Documents

By H. Cecil Spicer

THE results described in this article are based on field work conducted during the periods April-May, 1939, and May-July, 1940. The United States Potash Co. is mining potash on Government land under a permit from the Department of the Interior and the geophysical investigation was completed under a cooperative arrangement made between that company and the Conservation Branch of the Geological Survey. The writer, a member of the Section of Chemistry and Physics of the Geologic Branch, was assigned to this investigation. Four definite objectives were in mind for the geophysical work in the studies over the salt deposits. The first was to determine the measure of success that could be attained in this type of work with the resistivity methods that were to be employed. These methods had been introduced into the work of the Conservation Branch by Benjamin E. Jones for the investigation of dam sites, and have been used under his direction by the author for such work. If the method proved to be applicable, an effort was to be made to contour the top of the salt beds and also the other formation boundaries known to be present in this area. Salt-water aquifers were to be studied in an effort to determine their boundaries, and an attempt was to be made to delineate the potash-bearing beds. EARLIER STUDIES Others have made, and reported, resistivity studies over saliferous deposits in different areas. Friede1 and Messrs. Schlumberger2 reported geophysical work performed in the discovery of the salt domes of Alsace; Carrette and Kelly3 described the geology of the same area. Leonardon and Kelly4 published a resistivity curve obtained over the Hettenschlag dome, and a further discussion of this same area was given by the Messrs. Schlumberger5 in a communication. Messrs. Alty6 described studies on salt deposits in which the single-probe method was used. Sinerez7 mentions that electrical methods were tried over salt deposits in Spain. Geoffrey and Charrin8 show a resistivity curve obtained over marl, gypsiferous marl and salt which is similar to that obtained over the New Mexico salt deposits. Kelly9 reported resistivity work performed with the ground comparator of Zuschlag over the salt deposits near Syracuse, N. Y., where the Salina formation is at a depth of 700 to B00 ft. Some structural studies on the potash basin of Alsace are described by Poldini.10 Another single-probe resistivity study, made over salt deposits in New Mexico, is briefly described by Heiland,11 through the courtesy of Harry Aurand, of the Midwest Refining Co.

Jan 1, 1941

By Sidney A. Swensrud

The 24-in. crude-oil line. and- the 20-in. petroleum-products line, built as a war emergency by the United States Government and running from points in Texas to the New York-New Jersey-Philadelphia area, were constructed only because of the inability during the war to continue nor-inal ocean tanker movements from the Gulf Coast to the East Coast. The postwar disposition of these lines may be considered as one of the important problems of the postwar readjustments in the oil industry, if not the most important one. In the first place there appear to be many complications in keeping the lines in crude-oil or petroleum-products service. This conclusion was reached also in a study by T. E. Swigart, President of Shell Pipeline Corporation.' Since the lines are too largc for any one company to utilize, and since it appears likely that a surplus rather than a deficiency of tankers will exist after the war, most companies probably will feel that they can achieve lower costs and more satisfactoiy results from the resumption of tanker movements to the East Coast rather than by endeavoring to take over or utilize the capacity in the large pipe lines under some tariff-rate structure. As for using the lines for making deliveries to the middle west or central eastern areas, it would appear that when the war is over and normal transportation arrangements can be resumed, there will be no need of any extra capacity for such deliveries. Therefore, the War Emergency lines could be utilized for this purpose only if privately owned pipe lines and other transportation facilities were to be displaced. Against this rather unprepossessing prospect for use in petroleum or product service is the fact that at or near the source of the lines lie the greatest developed gas reserves in the world, for much of which there is at present no satisfactory market outlet; and at the other end of the lines lies one of the greatest concentrations of population in the world, which is not now served by natural gas. These who have been fortunate enough to use natural gas can have little doubt of its desirability as a domestic fuel. An analysis of the market potentialities and comparison with other areas where natural gas is being distributed, and where it has displaced manufactured gas, makes it seem clear beyond question that the full capacity of both of the large-diameter lines could be fully utilized in this service, and this without creating any undue drain upon the gas reserves of the nation. On the basis of an estimated capacity of roo to 120 billion cubic feet per year, the gas that might be marketed through these lines would amount to only 3 to 4 per cent of the total con-

Jan 1, 1944

By Sidney A. Swensrud

The 24-in. crude-oil line. and- the 20-in. petroleum-products line, built as a war emergency by the United States Government and running from points in Texas to the New York-New Jersey-Philadelphia area, were constructed only because of the inability during the war to continue nor-inal ocean tanker movements from the Gulf Coast to the East Coast. The postwar disposition of these lines may be considered as one of the important problems of the postwar readjustments in the oil industry, if not the most important one. In the first place there appear to be many complications in keeping the lines in crude-oil or petroleum-products service. This conclusion was reached also in a study by T. E. Swigart, President of Shell Pipeline Corporation.' Since the lines are too largc for any one company to utilize, and since it appears likely that a surplus rather than a deficiency of tankers will exist after the war, most companies probably will feel that they can achieve lower costs and more satisfactoiy results from the resumption of tanker movements to the East Coast rather than by endeavoring to take over or utilize the capacity in the large pipe lines under some tariff-rate structure. As for using the lines for making deliveries to the middle west or central eastern areas, it would appear that when the war is over and normal transportation arrangements can be resumed, there will be no need of any extra capacity for such deliveries. Therefore, the War Emergency lines could be utilized for this purpose only if privately owned pipe lines and other transportation facilities were to be displaced. Against this rather unprepossessing prospect for use in petroleum or product service is the fact that at or near the source of the lines lie the greatest developed gas reserves in the world, for much of which there is at present no satisfactory market outlet; and at the other end of the lines lies one of the greatest concentrations of population in the world, which is not now served by natural gas. These who have been fortunate enough to use natural gas can have little doubt of its desirability as a domestic fuel. An analysis of the market potentialities and comparison with other areas where natural gas is being distributed, and where it has displaced manufactured gas, makes it seem clear beyond question that the full capacity of both of the large-diameter lines could be fully utilized in this service, and this without creating any undue drain upon the gas reserves of the nation. On the basis of an estimated capacity of roo to 120 billion cubic feet per year, the gas that might be marketed through these lines would amount to only 3 to 4 per cent of the total con-

Jan 1, 1944

FRank FirmstoNe, Easton, Pa.: The effect of lead on brass seems to have been recognized by Berthier, and the facts published by him as early as 1818 (Ann. des Mines, 1st ser., iii., 1818, p. 347 et seq.). He there says expressly that copper containing lead makes " dry " (see) brass, and that, for the same reason, blast-furnace

Jan 1, 1898

By H. L. Gilbert, H. A. Johansen, R. G. Nelson

High purity electrolytic chromium plate has been hydrogen-reduced and arc-melted under inert atmosphere to give sound ingots. These ingots may be hot forged to break the as-cast structure and then worked at 500°C to finished form. An intermediate and final high temperature anneal gives best ductility and grain refinement. HE increasing interest in refractory metals for I use in high temperature gas turbines, jets, and rockets has led to great efforts in exploiting the fifth and sixth groups of transition elements. Much of the interest has centered upon production of metals that can be worked and fabricated by normal means to produce various engine parts or components having the high temperature characteristics of oxidation resistance and high creep strength required for such uses. If these pure elements do not exhibit all of the desired characteristics, it may be possible to obtain a high purity alloy that will. Since, in all cases, development of these transition elements has depended to a large extent upon removal of oxygen and nitrogen as a means for producing ductile metal, the hypothesis has been accepted that oxygen is the normal embrittling material in a high grade electrolytic chromium metal. Various methods have been employed in an effort to remove this oxygen by direct or indirect attack.' Many workers have endeavored to produce pure chromium through reduction of the oxide by carbon or active metals, while others have recommended fusion electrolysis of chromium salts or reduction of these salts by active metals, such as sodium or calcium. Hydrogen reduction of the oxide or chloride and thermal dissociation of the iodide have been reported to give high purity metal. Experimental Work The U. S. Bureau of Mines, Northwest Electro-development Laboratory, has systematically re-examined the more promising methods and developed two which produce metal having ductility at temperatures lower than heretofore described. It has been found' that oxide-free chromium chlorides in a NaCl-KCl carrier salt may be mag- nesium-reduced and the byproduct salts distilled off in vacuo to give a high purity chromium sponge. Fusion analysis conducted under the supervision of W. W. Horton of Knolls Atomic Power Laboratory showed the oxygen and nitrogen both to be below 10 parts per million on a selected sample. A small amount of carbon is carried over in the final metal from the chlorination and reduction steps which are carried out in graphite crucibles. This trace of carbon is not detrimental to hot ductility. A more practical method for producing ductile metal is through hydrogen reduction of high purity electrolytic chromium. Normal electrolytic chromium will, if "developed" for a few minutes at 1100°C in high vacuum, be found by the method of Adcock:; to contain about 1 pct chromium sesquioxide (Cr2O3). This small amount of oxygen may be effectively reduced by hydrogen.2, 4 The method employed was to crush electrolytic chromium plate in a gyratory crusher to pass 60-mesh; finer crushing appears to offer no advantage. A nitric acid leach removed the iron picked up during crushing. The leached powder was rinsed until neutral with distilled water and vacuum-dried.

Jan 1, 1954

By R. F. Mehl, J. T. Ransom

For many years the Metals Research Laboratory of Carnegie Institute of Technology has been concerned with the statistical nature of the engineering properties of steel from an experimental viewpoint, particularly those properties representing ductility.' In the past three years new work has been directed toward evaluating the statistical nature of the endurance properties. It has been shown that both the fracture curve and the endurance limit in fatigue are markedly statistical in nature. The S-N curve (and the endurance limit) of ferrous materials is often determined with specimens which number as few as ten. The common procedure is to test the first specimen at a stress well above the expected endurance hmit. Each succeeding specimen is then tested at a progressively lower stress, until, after five or six tests, a specimen runs ten million or so cycles without failing. Two or three more specimens are then used to find the highest stress at which failure will not occur; the limiting stress determined in this way is called the endurance limit. It has now been found, however, that the variability in the fracture curve and in the endurance limit in heat-treated alloy forging steels is so great that S-N curves must be drawn on the basis of distribution curves which can be appraised only by statistical methods. Two methods have been adopted in this study: (1) straightforward statistical studies of cycles to fracture of a number of specimens at each of a series of stress levels, and (2) a new abbreviated statistical method, known as "staircase testing."2 The latter corisists in testing a series of specimens, one by one, with the test stress for any given specimen automatically

Jan 1, 1950

By Benjamin Talbot

(New York Meeting, February 1913.) THE problem of segregation and cavities in steel ingots is a subject which has given and is still giving metallurgists, en¬gineers, and operators matter for serious consideration.. This question has come more into prominence lately in the United States, clue largely to the desire of railroad engineers to secure a better rail than they have obtained in the past, as the service they demand is increasing in severity; and no doubt manufacturers will be able to meet what is required of them. The rails here are as good as those made in other countries, but the conditions of service and the extremes of climate are more severe and consequently more breakages occur. Various reasons have been advanced to explain why rails may not be as good in quality to-clay as in the past. Some engineers consider that modern methods of manufacturing, designed chiefly to obtain large output, tend to reduce the standard of excellence of more deliberate methods. Others think that 4-ton ingots are worse than those of 2 tons. Again, it is .stated that the 100-ton heat in one ladle is too large, and is a :step in the wrong direction in casting. My experience upon the question of the size of the ingot is that in rolling rails of from 85-to 100-lb. sections, the range of ingot is only practically such that the difference in the size does not help in the question of segregation, cavities, or blow-holes.

Jan 4, 1913

By Alan Morris

In a previous paper1 the results of cutting tests on free-cutting brass rod were reported. Investigation was made of the effects of variation in lead content, microstructure and cold drawing. The author's reply to the discussion of that paper includes a study of the directional cutting properties of drawn and annealed rod. The present paper records the results of tests made on series of samples in which the tin, iron and copper contents have been varied. The apparatus used and method of testing are described in detail in the previous paper. The machine is of the pendulum-operated milling type used and described by Airey and Oxford.2 Angular readings of the height to which the pendulum rises after falling from a fixed position, both when a cut is made and when the pendulum swings freely, give the basis for calculation of the energy consumed in making a cut. Careful weighing of the sample before and after cutting gives a measure of the amount of metal removed. The results are expressed in footpoiinds per cubic inch of metal removed, and have been called "unit cutting energy." In the course of the discussion of the author's earlier paper, W. B. Price reported large-scale tests involving some 50,000 lb. of material. These tests indicated that the addition of as much as 0.6 per cent of iron and 0.25 per cent of tin had apparently no adverse effect on the highspeed cutting characteristics of the rod. The rod also contained a small amount of nickel. The test results reported here tend to confirm his observations. Effect of Variation in Tin Content The castings for this series were made 2 by 1 by 9 in. and were processed as follows: 1. Castings were annealed at 500" C. for 7 hr. 2. Cold-rolled to 0.700 in.

Jan 1, 1933

By Frank Firmstone

In April, 1873, No. 2 furnace at the Glendon Iron Works being out of blast, it was decided to alter it from an open to a closed top. The three side flues, through which a part of the gas was formerly taken off, were 15 feet below the top, and as, for various reasons, it was not convenient to cut new flues through the brickwork at the top, as is commonly done with closed-top furnaces, a modification of Coingt's charger was employed. This apparatus, as figured by De Vathaire,* consists of a cup or hopper, like that used with the cup and cone, and a central pipe for taking off the gas, which descends some distance into the furnace, and has a projection around it forming a seat for a ring of a triangular cross-section, which closes the opening between the cup and the central gas-pipe. The charge is put into the cup, and by lowering the ring, is thrown into the furnace, a part going outside of the ring toward the walls, and a part through the inside toward the gas-pipe. In this form the apparatus was not applicable, for: 1st. With a gas-pipe three feet in diameter, in a top eight feet in diameter, the openings left by lowering the ring would not be large enough to let lump coal pass through. 2d. For the charger to shut tight, the ring must bear equally against the projection made for it on the gas-pipe, and against the edge of the cup. This would not be difficult to effect when the apparatus is first put up, but a comparatively small change in the relative position of the parts, such as is almost certain to occur from expansion, would cause the ring to touch the pipe or the cup, whichever happened to be the lower, first, and leave a leak between it (the ring) and the other. In the plan adopted (Figs. 5 and 6, Plate I), the central opening in the ring is closed by the bottom of the gas-pipe, whereby more room is left for the passage of the stock when the charger is open, than if the pipe descended into the furnace; and the pipe, instead of being rigidly supported, rests on the ring, when the charger is closed, and follows it for two or three inches as it opens, until stopped by the counter-balance lever C. When the ring is raised to close the furnace top, it comes in contact first with the bottom edge of the gas-pipe, then both are raised together, until stopped by the ring touching the edge of the cup. In this way a good joint is made at both places.

Jan 1, 1967

Jan 1, 1967

By L. O. Howard

THE practice of using acid-lined converters at the plant of the Old Dominion Copper Mining & Smelting Co. was discontinued early in January, 1913, and they were replaced by basic-lined converters. The new equipment consists of one electrically operated 12-ft. upright converter stand and two basic-lined shells for same. These shells are provided with twenty-four 1 1/4-in. tuyères. The mouths are 5 ft. in diameter. Owing to the fact that there is no bedding system or other large storage capacity between the mine and the smelter, the furnaces must handle as fast as produced ore and concentrates, which may vary considerably from day to day, both in tonnage and copper content. Consequently the converter is often crowded to its utmost capacity by the frequent fluctuations in the daily matte supply. From the foregoing, it will be seen that in no way can the converter be favored by running light charges or by transferring to it from other stands in operation. Neither can it regularly be allowed to cool between blows, and only occasionally can it be run at as low a temperature as might be wished. No copper precipitate or other foreign material high in copper is available to help out the tonnage. Repairs and alterations or the removal of defective tuyères must wait until such time as a slight falling off in the matte supply-allows the converting operations to ease up. These variable conditions all combine to interfere with the systematic operating of the converter.

Jan 7, 1914

By Ronald F. Ayers

The basic research for this study was conducted by Battelle's Columbus Laboratories in 1974. The high-sulfur content of coal threatens to erode its competitive position in the future. The impact of sulfur removal on final costs of eastern interior coal lies at the very heart of this market analysis. An extensive market survey was conducted that considered both traditional coal markets as well as anticipated future markets. Competition for coal from this province considers low-sulfur Western coal, nu- clear power, international oil and coal trade, as well as Appalachian coal producers. Based on projections of future energy consumption under several scenarios, a comprehensive market forecast for eastern interior coal was made to 2040. The study upon which this paper is based was completed by Battelle's Columbus Laboratories for the U.S. Army Corps of Engineers in 1974. It is but part of an overall effort by the Corps to evaluate the costs and benefits to the nation of waterway improvements. This study is primarily concerned with future coal markets for production from those counties near the Wabash River in the heart of the Eastern Interior Province. An objective here is to consider a most pessimistic energy (and hence, coal) demand for planning purposes.

Jan 1, 1978

By Henry N. Toler

Development in the Jackson gas field, Hinds and Rankin counties, for 1935 continued at a slow pace, there being only nine wells drilled on the structure, of which five resulted in gas producers and four in dry holes. There were no wells drilled deep enough during 1935 to test any of the horizons below the producing Selma chalk. There are 113 producing gas wells in the Jackson gas field, with three wells on the southeast edge of the field making some oil with a large quantity of salt water; this oil comes from the same horizon as the gas. The combined open flow of the 113 gas wells is about 4,100,000,000 cu. ft. The proven area of the field is approximately 8000 acres. The production of 10,291,000,000 cu. ft. for 1935 represents the largest yearly pull from the field by almost a billion cubic feet. The total production from the field to date is 45,104,000,-000 cu. ft. It is interesting to note that the rock pressure has dropped from 1010 lb. per sq. in. initial to 943 Ib. at the end of 1935, a decline of only 67 lb. in 6 years. There is a difference of opinion as to the age of the deepest formation tested on the Jackson structure; some people holding that it is Tuscaloosa, others, Trinity, and still others that it is Paleozoic, probably Pottsville. The production of the Amory gas field, Monroe County, continued to decline and the capacity was far under the demand. Originally there were four producing wells in the field with a combined open-flow capacity of approximately 15,000,000 cu. ft. and a rock pressure of 680 lb. per sq. in. At the end of 1935 only two wells were producing with a combined open-flow of less than 1 million cu. ft. and the rock pressure down to 100 lb. or less. No attempt has been made to drill new wells in the immediate field but three wells are being drilled in the county in an effort to secure new supplies of gas. The wildcat operations for 1935, with only 11 wells drilled, were the lowest since 1932, just about one-half the number drilled during 1934. None of the wildcat wells drilled in 1935 resulted in producers and, so far as the writer is aware, did not uncover any large structures. The 11 wells drilled were abandoned or junked at comparatively shallow depths, except the well drilled in George County to 6928 ft. by the United Gas

Jan 1, 1936

By Henry N. Toler

Development in the Jackson gas field, Hinds and Rankin counties, for 1935 continued at a slow pace, there being only nine wells drilled on the structure, of which five resulted in gas producers and four in dry holes. There were no wells drilled deep enough during 1935 to test any of the horizons below the producing Selma chalk. There are 113 producing gas wells in the Jackson gas field, with three wells on the southeast edge of the field making some oil with a large quantity of salt water; this oil comes from the same horizon as the gas. The combined open flow of the 113 gas wells is about 4,100,000,000 cu. ft. The proven area of the field is approximately 8000 acres. The production of 10,291,000,000 cu. ft. for 1935 represents the largest yearly pull from the field by almost a billion cubic feet. The total production from the field to date is 45,104,000,-000 cu. ft. It is interesting to note that the rock pressure has dropped from 1010 lb. per sq. in. initial to 943 Ib. at the end of 1935, a decline of only 67 lb. in 6 years. There is a difference of opinion as to the age of the deepest formation tested on the Jackson structure; some people holding that it is Tuscaloosa, others, Trinity, and still others that it is Paleozoic, probably Pottsville. The production of the Amory gas field, Monroe County, continued to decline and the capacity was far under the demand. Originally there were four producing wells in the field with a combined open-flow capacity of approximately 15,000,000 cu. ft. and a rock pressure of 680 lb. per sq. in. At the end of 1935 only two wells were producing with a combined open-flow of less than 1 million cu. ft. and the rock pressure down to 100 lb. or less. No attempt has been made to drill new wells in the immediate field but three wells are being drilled in the county in an effort to secure new supplies of gas. The wildcat operations for 1935, with only 11 wells drilled, were the lowest since 1932, just about one-half the number drilled during 1934. None of the wildcat wells drilled in 1935 resulted in producers and, so far as the writer is aware, did not uncover any large structures. The 11 wells drilled were abandoned or junked at comparatively shallow depths, except the well drilled in George County to 6928 ft. by the United Gas

Jan 1, 1936

By K. P. Gupta

In ternary systems containing silicon and transition elements, silicon was found to stabilize the a phase.1 At 1000°C a broad a-phase region was found in the Cr-Mn-Si system,1 which extends very close to the Mn-Si binary line (within about 3 at. pct Cr). Later investigation showed that, if chromium was replaced by small amounts (3 to 5 at. pct) of v,1 Ti, Nb, Ta, Mo, or w,1 the a phase or the R phase was again stabilized. Whether stabilization of complex crystal structures is possible by small additions of iron, cobalt, or nickel to Mn-Si is not known. Investigation of the Co-Mn-Si system4 shows the presence of several ternary phases, but at cobalt concentrations higher than 10 at. pct. In the present work the ternary systems Fe-Mn-Si and Co-Mn-Si were investigated at low iron and cobalt concentrations (< 7 at. pct Fe or Co) in search of phases of complex crystal structure. Experimental Procedure. The alloys were pre-pared by induction melting Co (99.8 pct), Si (99.9 pct), electrolytic Fe (99.88 pct), and Mn (99.9 pct) in recrystallized alumina crucibles under an inert atmosphere of argon gas. The alloy specimens were wrapped in molybdenum foil, sealed in argon-filled (at 1/2 atm) silica capsules and annealed for 72 hr at 1000" 1°C, and water-quenched. The use of argon-filled capsules was found to reduce the losses during annealing and the molybdenum foil prevented reaction of the manganese with silica. The total weight loss due to annealing and melting was found to be less than 1 pct for each alloy. The alloys were not analyzed chemically. A part of each annealed specimen was polished and examined metal-lographically using etching solutions, a) 0.1 to 0.5 pct oxalic acid solution in water, or b) 0.5 pct HNOs in methyl alcohol. Even though the etching solutions were quite dilute, the specimens were heavily etched and stained if the etching time exceeded more than 5 sec. Etching times found suitable were usually 1 to 3 sec. For X-ray diffraction work, a part of each annealed specimen was powdered by crushing after the exposed surface was ground off. X-ray diffraction patterns were taken with powder specimens using a 20-cm-diam asymmetrical focusing camera and Fe K radiation. These powder patterns were found quite satisfactory for the purpose of phase identification. However, X-ray diffraction patterns of single-phase alloy powder specimens were also taken using a Siemens diffractometer and filtered Cr-Ka radiation for greater resolution of the diffraction lines. Results and Discussion. In the Fe-Mn-Si system a new ternary phase was found at 1000°C between the p manganese and the MnsSi phase regions. The approximate phase relationships in this region of the 1000°C isothermal section are shown in Fig. 1. The new ternary phase, designated as the K phase, was found to occupy a narrow region about 1 at. pct in width and extending from Fee.oMn74.5Silg.5 to Fe.Mn.Silg.. At the high-iron content region, the K phase was found in equilibrium with the p manganese and the MnsSi phases but, at the low-iron content end of the K-phase region, the phases in equilibrium with the K phase were the p manganese phase, the MnsSi phase, and another new phase, designated in Fig. 1 as the v phase. The v

Jan 1, 1964

By A. F. Lucas

Introduction BELLE ISLE, located in the low sea marshes near Atchafalaya Bay, is the southeasternmost of the famous Five Salt Islands of Louisiana. Rising about 80 ft. (24 m.) above the level of the surrounding marsh and being some 800 acres (323 ha.) in extent, it constitutes a striking landmark on the low Gulf coast, and since the eighteenth century, when it played an important part in the operation of the buccaneers, it has been intermittently frequented by man. In 1897, the writer discovered the great mass of salt that underlies the island and shortly afterward pub-lished a brief account of the geology of Belle Isle and the neighboring salt islands.&apos; In that paper he described principally the salt, but pointed out also the occurrence of petroleum and of sulphur in the strata above the salt. Since that time the island has been extensively explored by the drill, and the developments up to 1908 have been described by Veatch2 and Harris," and Knapp.4 The writer&apos;s early conclusions as to the probable presence of sulphur in considerable quantity have been confirmed by the later drilling, some of the wells having found quantities of gas containing sulphur dioxide and a number of sulphur-bearing strata as well. Under the stimulus of the present keen demand for sulphur for war purposes, a syndicate of New York capitalists was recently formed to explore the sulphur resources of the island in more detail. Under the writer&apos;s direction, six wells were drilled for this syndicate during the winter of 1916-17. The present paper presents briefly the results of this work and sums up the present knowledge of the geology of this highly interesting locality.

Jan 9, 1917

By Z. F. Danes

Combination of gravity data and density logs makes it possible to determine the structural relief. Under a wide class of geologic conditions, the solution is unique, or limited to a single parametric system of solutions. As a useful byproduct, the method yields a new way to construct derivative maps, continue the field up or down, subtract regional anomalies, and perform smoothing. In the past, the problem of interpreting gravity anomalies in terms of structural geology was solved along two main lines: 1) A body of a certain shape and density contrast was assumed and the corresponding gravity anomaly calculated, analytically for simple bodies, graphically and/or numerically for more complex ones; then the computed anomaly was compared with the observed one, and the assumed shape corrected according to the differences between the two. 2) The anomaly is assumed to come from a warped interface between two media of different density; the relief of the warping is assumed small compared to the depth of burial, so that the structure can be approximated by a flat horizontal surface of variable density distribution. The first method is a standard technique, described in every text book on applied geophysics, and is well applicable, for bodies with predominant vertical dimension. The second one, probably first used by Tsuboi and Fuchida,&apos; is mathematically more elegant. It applies to the fashionable field of integral transforms (Bullard and Cooper, 2 Tomoda and Aki, 3 Dean 4) and is useful mainly in cases when the vertical relief of the structures is comparatively small. 30th methods, tacitly or openly, assume a density discontinuity across the boundary of the two media, while within each medium the density is constant. However, the recent invention of the gamma-gamma

Jan 1, 1962

By Frank Firmstone

IN April, 1873, No. 2 furnace at the Glendon Iron Works being out of blast, it was decided to alter it from an open to a closed top. The three side flues, through which a part of the gas was formerly taken off, were 15 feet below the top, and as, for various reasons, it was not convenient to cut new flues through the brickwork at the top, as is commonly done with closed-top furnaces, a modification of Coingt&apos;s charger was employed. This apparatus, as figured by De Vathaire,* consists of a cup or hopper, like that used with the cup and cone, and a central pipe for taking off the gas, which descends some distance into the furnace, and has a projection around it forming a seat for a ring of a triangular cross-section, which closes the opening between the cup and the central gas-pipe. The charge is put into the cup, and by lowering the ring, is thrown into the furnace, a part going outside of the ring toward the walls, and a part through the inside toward the gas-pipe. In this form the apparatus was not applicable, for: 1st. With a gas-pipe three feet in diameter, in a top eight feet in diameter, the openings left by lowering the ring would not be large enough to let lump coal pass through. 2d. For the charger to shut tight, the ring must bear equally against the projection made for it on the gas-pipe, and against the edge of the cup. This would not be difficult to effect when the apparatus is first put up, but a comparatively small change in the relative position of the parts, such as is almost certain to occur from expansion, would cause the ring to touch the pipe or the cup, whichever happened to be the lower, first, and leave a leak between it (the ring) and the other. In the plan adopted (Fig&apos;s. 5 and 6, Plate I), the central opening in the ring is closed by the bottom of the gas-pipe, whereby more room is left for the passage of the stock when the charger is open, than if the pipe descended into the furnace; and the pipe, instead of being rigidly supported, rests on the ring, when the charger is closed, and follows it for two or three inches as it opens, until stopped by the counter-balance lever C. When the ring is raised to close the furnace top, it comes in contact first with the bottom edge of the gas-pipe, then both are raised to¬gether, until stopped by the ring touching the edge of the cup. In this way a good joint is made at both places. * Etudes our lea Haut Fourneaux, page 108.

Jan 1, 1874

By John P. Bryant

Plant nutrients are obtained by plants from both the air and the soil. Carbon dioxide, a gaseous form of carbon and oxygen, supplies the carbon which usually makes up 50% or more of plant structure. Plants are capable of absorbing carbon dioxide directly from the air. Most of this nutrient comes from the air, although some carbon dioxide is absorbed by soil water and taken into the plant as liquid. Growing plants use more water than any other substance. Plant nutrients in the soil dissolve in soil water; soil water entering the plant carries nutrients into the plant structure. Water is then given off into the air as the plant breathes or transpires. The inorganic or mineral portion of the nutrients which plants require comes from the soil. Inorganic or mineral composition of plants is usually less than 5% of their weight, and this mineral requirement, usually lacking in the soil, must be provided by fertilizers. Proper fertilization of a soil to improve its mineral level and productivity is the basis for the fertilizer industry (Thomas, 1960). There are 13 essential plant nutrients which often must be added to soils or plants and are generally considered as fertilizer minerals. These nutrients are divided into the categories: primary minerals (nitrogen, phosphorus, potassium); secondary minerals (calcium, magnesium, sulfur); and micro or trace minerals (boron, iron, manganese, copper, zinc, molybdenum, chlorine). Further, cobalt is often added to fertilizers. Although it is not considered to be an essential plant nutrient, it is essential to animal health and is often applied to forages as a fertilizer constituent. One point of major significance to the fertilizer industry is that not all nutrient carriers supply that nutrient in a chemical form which will be available to the plant. Thus, a product which may be considered a fertilizer mineral may require substantial processing or treatment before it becomes useful as a nutrient carrier. Fertilizer Industry Scope Until about 1900 demands for higher crop yields were met simply by bringing new agricultural lands into cultivation. Since that time great progress has been made in increasing yields through fertilization and improved varieties and cultural practices. The importance of the fertilizer industry to the economy and welfare of the U.S. is widely recognized. [Fig. 1] illustrates the relationship of lime and fertilizers to crop yields. In terms of tons of fertilizer products, the growth of the industry has been phenomenal, particularly between 1950 and 1970. Table 1 shows the increase in fertilizer usage. Primary Plant Nutrients in Fertilizers Primary minerals (nitrogen, phosphorus, potassium) are designated as such because of their significance to plant growth. Practically all soils are deficient in both nitrogen and phosphorus, and most of them are also deficient in potassium. Consequently, these nutrients

Jan 1, 1975