Search Documents

By R. G. Beverly

The presence of radioactivity in uranium mill wastes has resulted in somewhat unique waste disposal methods. In addition to the common problems of disposing of large quantities of solid wastes, neutralizing acids, minimizing dissolved heavy metals, and clarifying all liquid effluents, the uranium mill operator must sample and analyze liquid effluents for micro-micro-quantities of radio- nuclides such as Ra226, Th230, and Pb210. Special disposal methods or decontamination procedures are required to meet the stringent limitations established by the U.S. Atomic Energy Commission on the concentration of radionuclides in liquid effluents. Routine monitoring of the receiving stream is also normally required. In recent years there has been a growing concern about the radioactivity remaining in uranium mill tailings, particularly at the sites of shut-down or dismantled mills. The State of Colorado, in cooperation with the industry, has adopted regulations for stabilization of inactive uranium mill tailings.

Jan 6, 1968

By D. W. Frommer, M. M. Fine

Mineral dressing research showed that iron concentrates of commercial quality could be produced from the Pea Ridge deposit near Sullivan, Mo. Magnetic separation and flotation, on a laboratory scale, yielded concentrates ranging from 60.0 to 71.4 pet Fe at recoveries of 89.9 to 97.6 pct. Early in 1957 St. Joseph Lead Co. announced discovery of three new centers of iron ore deposition in east central Missouri.' The discovery resulted from exploratory drilling in the vicinity of a magnetic anomaly or high. A deep hole, drilled into the Pre-Cambrian porphyry to determine the cause of anomaly, penetrated a magnetite-rich deposit.' The magnetic surveys that revealed the anomalies were begun by the Missouri Geological Survey in 1929 and were continued into the 1930's.3 At that time an area in Crawford County known as the Bourbon magnetic high was located. A second anomaly, similar in size and intensity, was discovered about six miles to the northeast in Franklin County in the vicinity of Sullivan. This area was not studied in detail until the early 1940's. To determine the cause of the anomalies, the USBM drilled four holes at the Bourbon site in 1943-1944.4 The most productive hole penetrated four mineralized zones having a total thickness of 127.5 ft. These zones contained magnetite in rhyo-lite porphyry at depths between 1600 and 2000 ft. Additional iron ore below 2000 ft was considered a possibility at the time. Some years later, the USGS, Missouri Geological Survey, St. Joseph Lead Co., and others cooperated in sponsoring an aeromagnetic survey of the Bourbon-Sullivan area which resulted in discovery of a third high, about eight miles distant at Pea Ridge. This deposit, with an estimated reserve of 50 to 100 million tons of iron ore, is considered the main find, although other orebodies in the same general area are of definite interest.' When this discovery was announced, St. Joseph Lead also revealed plans to exploit the deposit jointly with Bethlehem Steel Co. A new corporation, Meramec Mining Co., was established, and 1962 was set as the target date for completing physical plant.2 Annual production goals of 2 million tons of beneficiated and pelletized iron ore were proposed. Preparation of the site for shaft sinking was begun in June 1957. Orebody and Character of Samples: Drilling to date has established the Pea Ridge orebody as a crescent-shaped pipe about 300 ft wide. Some drillholes were bottomed at 2800 ft in very good iron ore.6 he orebody is predominantly magnetite, although hematite and a mixture of hematite and magnetite occur in the upper areas and peripheral walls. Drillhole cores representing ore from different areas and depths of mineralization were grouped into composites for testing. These composites consisted of: 1) medium grade mixed hematite and magnetite, 2) high grade mixed hematite and magnetite, and 3) high grade magnetite. The medium grade ore came from three holes with depths of i350 to 1900 ft. The high grade mixed hematite and magnetite cores came from the 1790 to 2812-ft interval of one hole. Partial chemical analyses of the three samples, given in Table 1, reveal that all are excessively high in phosphorus and sulfur, and sample 1 is

Jan 1, 1960

By R. E. Reed-Hill

The shear continuity conditions under which one mechanical twin may cross another are considered. Twin intersections usually involve various types of slip deformation in addition to twinning. Because the shear of the crossing twin may be partly transmitted through the crossed twin by slip mechanisms, continuity of the twinning shear vectors is not required at a twin intersection. It is concluded that analyses based on twin intersections should not he used as an independent method for deducing twinning elements in newly observed twinning modes. WHEN one mechanical twin passes through another, a twin intersection is said to occur. In the simplest form of intersection, Fig. 1, the crossing of one twin by another is accomplished with the aid of a second-order twin induced, in the twin that is crossed, by the crossing twin. The subject of twin intersections is significant to the field of deformation studies because it has been postulated by cahn1 that twin intersections should occur only under the following continuity conditions: 1) the traces of the primary and second-order twin must be parallel to each other in the plane of the crossed twin; 2) the direction 771 and magnitude, S, of the twinning shear must be identical in the crossing and second-order twins; also, the sense of shear must be the same. If these postulates are valid they constitute a valuable tool for determining twinning elements of newly observed twinning modes in metals. In his classic paper in 1953 on the plastic deformation of a uranium, Cahn1 used these continuity conditions to deduce twinning elements for several uranium modes. However, in the same year, pratt2 showed that both of Cahn's continuity equations were violated for (1012) twin intersections in zinc. Later, Kiho and Maruyama3, 4 showed that Cahn's second postulate was violated in {301) and (101) twinning in tin and (101) twinning in bismuth. In spite of this documentation that Cahn's second postulate is often violated, several recent papers5'6 have been published which have attempted to use the condition of continuity of twinning shear vectors for the evaluation of twinning elements. The primary purpose of this paper is to call attention to the possible ambiguity inherent in applications of Cahn's postulate, and to present additional information concerning the nature of twin intersections.

Jan 1, 1964

By R. V. Ramani, T. S. Kovach

In many instances, the actual production from a longwall face does not equal the planned capacity. General problem areas that have been identified include face length and panel depth, face area and gate entry roof support, face conveyor and shearer wear, outby haulage system failures, number of entries in longwall gate development, and longwall move time. The performance of a longwall face is totally dependent on the interaction of these and other factors. To explore fully these interactions, a systems analysis of longwalls has been performed. In this paper, the systems approach, the factors considered in the analysis, and the results of the analysis are presented.

Jan 1, 1985

Jan 1, 1959

By J. E. Schaffer

Drilling activity in Ohio increased slightly in 1939. There were 1020 completions as compared to 910 in 1938. During the past six years the number of completions has varied little (Table 1). Oil production in Ohio has been gradually declining since 1896, when the peak production of 23,941,000 bbl. was reached (Fig. 1). Since that date production has slowly declined to an estimated production in 1939 of 3,144,134 bbl., the lowest in 53 years. This total production is divided approximately into the following grades of crude oil: Pennsylvania, 1,185,456 bbl.; Corning, 1,261,615 Flg 1. bbl.; Lima, 578,500 bbl.; Lodi, Based on figures of U. S. .Bureau of 104,740 bbl.; Cleveland, 13,823 Mines and Oil andGas Journal bbl. Table 2 shows the prices paid for the various grades of crude oil.

Jan 1, 1940

By J. E. Schaffer

Drilling activity in Ohio increased slightly in 1939. There were 1020 completions as compared to 910 in 1938. During the past six years the number of completions has varied little (Table 1). Oil production in Ohio has been gradually declining since 1896, when the peak production of 23,941,000 bbl. was reached (Fig. 1). Since that date production has slowly declined to an estimated production in 1939 of 3,144,134 bbl., the lowest in 53 years. This total production is divided approximately into the following grades of crude oil: Pennsylvania, 1,185,456 bbl.; Corning, 1,261,615 Flg 1. bbl.; Lima, 578,500 bbl.; Lodi, Based on figures of U. S. .Bureau of 104,740 bbl.; Cleveland, 13,823 Mines and Oil andGas Journal bbl. Table 2 shows the prices paid for the various grades of crude oil.

Jan 1, 1940

By F. O. Garrabrant

Power is furnished to the Climax Molybdenum Co. by the Public Service Co. of Colorado over two 100,000-volt lines to a bank of three 3333-kva. transformers 100/13.8 kv. These transformers are so designed that with the addition of forced cooling their capacity may be increased 331/3 Per cent at 12,000-ft. altitude. Under present conditions, these transformers are operated at 140 per cent of their rating with forced air cooling. On the secondary side of this bank there is a 15-kv., 1200-amp. Westinghouse oil circuit breaker provided with automatic reclosing relays allowing three successive short circuits before lockout. From this breaker 13.8-kv. power is transmitted to a central switching station (Fig. I) where all circuits radiate to the different operations of the property. Each circuit is protected by a 23-kv., 600-amp. oil circuit breaker with by-pass and isolating disconnecting switches.

Jan 1, 1947

By D. S. Choi, H. von Schonfeldt, H. D. Dahl

The design of pillars around a longwall panel in which the effect of the adjacent and worked-out panel is taken into consideration is discussed. A mathematical model is used to duplicate field observations such as opening closure and pillar rib movement. The model is then used to predict the effect of changes in mining geometry on the opening stability.

Jan 1, 1976

By L. W. McKeehan

IT is no longer necessary, if it ever was, for your annual lecturer to apologize for including in his remarks frequent references to the arrange-ment of metal atoms in crystals and for basing his arguments that metals behave as they do upon their crystal structure. Neither will any objec-tion be raised because the large metallic crystals of which we will speak are hard to prepare and of negligible commercial interest. The particular set of physical properties we propose to discuss-ferromagnetic proper-ties-may require more justification. Very few in this audience are primarily, or even remotely, interested in the ferromagnetic behavior of the metals they handle. By no means all of you ever deal, by choice or by necessity, with metals which display any ferromagnetism at all, and even those who study or control ferrous metallurgy must usually depend upon electrical engineers for assistance in ferromagnetic applications. My excuse for talking about such an obvious specialty is, like all Gaul, divided into three parts. In the first place, the members of the com-mittee who select the annual lecturer must wish the speaker to confine himself to matters he has at least thought about before he prepares his speech. In the second place, the study of ferromagnetism in crystals has, as you will soon realize, suffered in the not-too-distant past from inade-quate metallurgy. Further progress probably depends upon proper use being made of the skill and knowledge of some members of the Institute of Metals Division who have not, before today, been asked to think about the problems presented here. Finally, there is at least a sporting chance that the ferromagnetic properties of a few metal crystals will give some insight into the more generally interesting properties which they share with nonferromagnetic metal crystals.

Jan 1, 1934

By L. L. Wyman

THE resultant embrittlement caused by the exposure of oxygen-bearing copper when hot and exposed to reducing gases has been the subject of many studies.1 Little attention, however, has been given to the possible embrittling effects due to atmospheres or conditions that under some circumstances might be the source of a reducing gas. At rather infrequent intervals there occur reports of copper becoming embrittled during normal annealing cycles in commercial steam-atmos-hered furnaces such as customarily are used for this operation. As might be expected, several other factors exist-such as oil, dirt on the wire, or in the furnace, or metallic surface contacts that might produce reducing gases and be the source of the trouble. However, in consider-ation of the statement made by Ruder,2 it would seem that under some conditions steam itself might prove to be the source of trouble. A consideration of the amount of the dissociation of water vapor up to temperatures of the melting point of copper shows that' the amount of hydrogen that could come from this source is far too minute to account for any embrittlement. What such information does not tell is what will happen at the surface of copper when subjected to steam at elevated temperatures, for entirely different conditions may persist, which would account for Ruder's observation. Furthermore, there are no data as to what might happen at the surfaces of other materials present, the result-ant of which might affect the condition of the copper present. For this reason, it was decided to make a series of experiments com-parable to those previously conducted by the writer,1 which would clarify the effect of the steam on copper, and in copper in the presence of steel.

Jan 1, 1940

ALABAMA Anniston.-Carrington, F. G. Auburn.-Brown, R. L. Battelle.-Green, G. G. Bessemer.-Abbott, C. E. Dobbs, G. G. Ferguson, V. Birmingham.-Adams, J. H. Aldrich, T. H. Aldrich, T. H., Jr. Allen, A. W. Bonnyman, J. Bowron, J. Bush, M. W. Crawford, G. G. Crockard, F. H. Ellis, E. E. Fairbairn, C. T. Gallacher, J. Geismer, H. S.

Jan 1, 1917

By John W. Trammell, Chester O. Ensign

Efficient mining of copper ore at the White Pine mine in Michigan's Upper Peninsula is partially dependent on the rather unique problem of predicting variations and rock types in a barren stratum called the upper sandstone. The pronounced effect which this formation has on the local mining techniques is reflected by the necessity of deciding whether to mine the sandstone along with ore-bearing rock, thus diluting overall ore grade, or, alternatively, leaving the sandstone behind to form the mine roof. THE OREBODY AND MINING TYPES In the mine, the cupriferous zone of the Nonesuch shale is divided into three major portions (Fig. I). Lying conformably on top of the Copper Harbor formation (or "lower sandstone") is the lower part of the orebody, the parting shale. The parting shale is overlain by the upper sandstone. On top of the upper sandstone, the basal portion (8 ft) of the upper shale is quite similar to the parting shale. Both the upper shale and parting shale are divided into a number of smaller stratigraphic units, each having a characteristic copper content, as shown by the histogram of Fig. 1. Other authors have dealt in detail with the stratigraphy and mineralogy of the orebody, so it will suffice here to call attention to the low copper content of the upper sandstone.

Jan 12, 1964

By P. A. Witherspoon, R. W. Donovan, T. D. Mueller

The use of petroleum-barren aquifers for underground storage has become extremely important to the natural-gas industry. A critical problem in assessing the feasibility of a specific aquifer for such use is the permeability determination of the caprock over the proposed storage project. The approach used here is to conduct both static and dynamic field tests on the aquifer being analyzed. Valuable information on the possibility of communication between the storage aquifer and any other aquifers above can be obtained by measuring hydrostatic water levels and water analyses. Significant differences in such data give evidence of the lack of communication between the intended storage reservoir and other horizons. The dynamic approach requires that one well be pumped in the storage aquifer, and changes in fluid levels recorded in both the aquifer and its caprock. The interpretation of the data from such pumping tests involves the solution of nonsteady radial flow in an infinite aquifer and the influence on such flow of a leaky caprock. A finite-difference model has been used to investigate this problem, and the transient behavior has been solved numerically with a digital computer. It has been found that the pressure transients in the storage aquifer are not affected significantly by moderate caprock leakage. The pressure behavior of the caprock is a much better indicator of the degree of leakage, and generalized solutions for this behavior are included. Field data are presented to demonstrate both the static and dynamic approach. If is concluded that appropriate investigation of the groundwater hydrology in an aquifer-type gas-storage project can provide much valuable information for determining the effectiveness of the caprock to hold gas. INTRODUCTION Underground storage of natural gas in the United States has been developing at a rapid rate over the past few years. In 1955, the total gas-storage capacity was about 1.6 trillion cu ft; by 1961, this figure was almost 3.2 trillion cu ft, an increase of 100 per cent in six years.' This trend un- doubtedly will continue because the economics favor the development of gas storage, as opposed to the construction of new pipelines, to meet the inherent cyclic demand for fuel in the metropolitan areas of this country.' About 15 per cent of the current underground gas storage has been developed in petroleum-barren aquifers, i.e., geological domes or anticlines in which no commercial quantities of oil or gas had been produced prior to the storage operations. The necessity for using barren aquifers outside many metropolitan areas of this country has been due to the lack of depleted oil or gas fields that were near enough and large enough to meet the demands of such consuming areas. Pipeline companies have developed aquifer storage along their transmission lines to meet the fluctuating needs of their complex systems. Considerable thought has also been given to the problem of storing gas in a structureless aquifer, both in this country' and in the Soviet Union outside the city of Leningrad.'," Conditions such as these have led to the development of aquifer gas-storage projects in many parts of the U. S. Most of these developments have centered in the Mid-Continent area, and the greatest amount of activity has been concentrated in Illinois.6 Thus, the use of petroleum-barren aquifers for gas-storage purposes has become extremely important to the natural-gas industry. There are three basic problems in developing aquifer-type storage: (1) finding an adequate geologic structure, (2) finding a suitable storage reservoir within the structure and (3) determining the tightness of the caprock over the intended storage zone. The first two problems can be solved by applying conventional methods of exploration geology, but once these problems are solved, the question arises as to why no oil or gas is present in an otherwise favorable setting. Two situations are possible: (1) an adequate source bed was never present, or (2) a source bed was present but the petroleum seeped away because of a leaky caprock. Determining the tightness of the caprock is one of the most critical problems in assessing the feasibility of a specific aquifer for storage purposes. In attacking this problem, one usually takes cores of the caprock and subjects them to a rigorous investigation. Such core data are desirable, but they only detail the matrix properties and cannot be expected to reveal the gross characteristics of the caprock. Several gas-storage projects in the U. S. have had considerable leakage where

By E. P. Chartkoff, W. P. Sykes

In 1926 one of the authors published researches on the determination and description of the iron-tungsten and iron-molybdenum systems,' including the equilibrium diagrams. In 1929, further work was carried on, including the examination by X-rays, which is recorded here. Meas-urements were made of changes in lattice parameters in the solid solutions. Precipitation from the solid solution and the accompanying changes in hardness were studied as well as the formation of the intermetallic com-pound phases upon sintering a mixture of metal powders. Materials All the specimens were prepared from the same quality of metals and by the same methods as were described in the determination of the constitutional diagrams. The metal powders as mixed and pressed were sintered or fused in a hydrogen atmosphere and subsequently treated as indicated in the titles of the figures. The formation of the iron-rich solutlon in the solid was accomplished by sintering in hydrogen for a period of 20 to 30 hr. at a temperature 25' to 50' C. below the melting point of the eutectic. The tungsten-rich and molybdenum-rich solid solutions of iron were prepared by adding the iron as a solution of iron ammonium oxalate to the oxide of tungsten or molybdenum, followed by a hydrogen reduction. This method results in a homogeneous alloy after sintering the pressed metal powder for 20 to 30 hr. at a temperature slightly below that of the peritectic reaction in the system involved. For X-ray examination the specimens were variously prepared, depending on the nature of the sample and what it was desired to show. For example, the iron containing tungsten or molybdenum in solid solution was cut with a file, the chips were put through bolting cloth, and this powder of filings formed the specimens for comparative study. The

Jan 1, 1930

By A. R. Orban, R. B. Engdahl, J. D. Hummell

The initial phase of a research program on smoke abatement from Bessemer converters is described. In work sponsored by the American Iron and Steel Institute, a 300-lb experimental Bessemer converter was assembled to simulate blowing conditions in a commercial vessel. Measurements of smoke and dust were also made in the field on a 30-ton commercial vessel. During normal blows the dust loading from the laboratory converter averaged 0.51 lb per 1000 lb of exhaust gas. This was similar to the exhaust-gas loading of a commercial vessel. The addition of hydrogen to the blast gas of the laboratory converter caused a decided decrease in smoke density. Smoke was also reduced markedly when methane or ammonia was added instead of hydrogen. The research is continuing on a bench-scale investigation of the mechanism of smoke formation in the converter process. DURING the past 2 years, on behalf of the American Iron and Steel Institute, Battelle has been conducting a research program on the control of emissions from pneumatic steelmaking processes. The objective of the research program is to discover a practical method for reducing to an unobjectionable level the emission of smoke and dust from Bessemer converters. PRELIMINARY INVESTIGATION Although conceivably some new collecting technique may be devised which would be economically practicable for cleaning Bessemer gases, no such system based on presently known principles seems feasible because of the extremely large volume of high-temperature gases involved. Hence, the research is being directed toward prevention of smoke formation at the source. A thorough review was first made of former work to determine the present status of the cleaning of converter gases. No published work was found on work done in the United States on collecting smoke or on preventing its formation in the bottom-blown, acid-Bessemer converter. In Europe, however, a number of investigations have been made on the basic-Bessemer converter. Kosmider, Neuhaus, and Kratzenstein1 conducted tests on a 20-ton converter to obtain characteristic data for dust removal and the utilization of waste heat. They concluded that because of the submicron size of the dust, special equipment would be necessary to clean the exhaust gases. Dehne2 conducted a large number of smoke-abatement experiments at Duisburg-Huckingen in a 36-ton Thomas converter discharging into a stack. A number of wet-scrubbing and dry collectors were tried unsuccessfully. A waste-heat boiler and electrostatic collector with necessary gas precleaners was felt to be the best solution for this particular plant. Meldau and Laufhutte3 determined that the particle size was all below 1 µ in the waste gas of a bottom-blown converter. Sel'kin and zadalya4 describe the use of oxygen-water mixtures injected into a molten bath in refining open-hearth steel. They claim that with use of oxygen-water mixtures the amount of dust formed was reduced between 33.3 and 20 pct of its previous level, and emission of brown smoke almost ceased. Pepperhoff and passov5 attempted unsuccessfully to find some correlation between the optical absorption of the smoke, the flame emission, and the composition of the metal in a Thomas converter in order to determine automatically the metallurgical state in the melt. In a recent U. S. Patent (NO. 2,831,762)' issued to two Austrian inventors, Kemmetmuller and Rinesch, the inventors claim a process for treating the exhaust gases from a converter. By their method the inventors claim that the exhaust gases from the converter are cooled immediately after leaving the converter to a degree that oxidation of the metal vapors and metal particles to form Fe2O3 is inhibited in the presence of surplus oxygen. Gledhill, Carnall, and sargent7 report on cleaning the gases from oxygen lancing of pig iron in the ladle. They claim the Pease-Anthony Venturi scrubber removed 99.5 + pct of the smoke, thereby reducing the concentration to 0.1 to 0.2 grain per cu ft, which resulted in a colorless stack gas after the evaporation of water. Fischer and wahlster8 developed a small basic converter and compared the metallurgical behavior of the blow with that of a large converter. Later work by Kosmider, Neuhaus, and Hardt9 on the use of steam for reduction of smoke from an oxygen-enriched converter confirmed that the cooling effect of steam is detrimental to production. From review of all of the published information on the subject, it was concluded that a practical solution to the smoke-elimination problem had not been found. Accordingly, it was deemed desirable to investigate the feasibility of preventing the initial formation of smoke in the converter.

Jan 1, 1961

By S. S. Lisnyak, B. D. Lichter

An important question in the study of the "hot corrosion" phenomenon (i.e., accelerated oxidation of Ni-Cr-base and Co-Cr-base "superalloys" in the presence of sulfur) is the condition of formation and physico-chemical properties of different sulfides in the system Ni-Co-Cr-S. seyboltl has observed the presence of ((chromium-rich" sulfides of compositions M3S4, and M2S3 in the scales of superalloys after hot corrosion; however, as he points out, much confusion exists as to the identity of sulfides found on Ni-Cr and Co-Cr alloys. According to the literature,&apos; ternary sulfides, e.g., NiCr2S4, (monoclinic structure) and CoCr2S4 (spinel structure) exist in these systems. Therefore, it is likely that these compounds are found in the scale of alloys undergoing hot corrosion. At present this possibility has not been discussed in the literature. Accordingly, we have begun investigation on the properties of ternary sulfides and their mutual interaction. The magnetic and electrical properties of pure NiCr2S4 and pure CoCr2S2 have been previously determined."-&apos; In the present work we have studied the interaction between these sulfides at high temperatures by means of X-ray diffraction and magnetic susceptibility. The measurements were carried out at room temperature after appropriate thermai treatment of samples at high temperatures. For alloys containing the three elements nickel, chromium, and cobalt this interaction may be of importance in the study of the hot corrosion phenomenon. The compounds NiCr2S4 and CoCr2S4 were prepared from stoichiometric amounts of the elements and CoS in the case of CoCr2S4. Samples were mixed and sealed in evacuated silica tubes, slowly heated to 900&apos; to 100O°C, and held at temperature for a total of 120 hr (NiCr2S4) or 80 hr (CoCr2S4) with intermediate re-grinding~. X-ray diffraction showed a pure spinel structure for CoCr2S4 and a monoclinic structure for NiCr2S4. Samples of mixtures of the two ternary sulfides were prepared with different compositions, see Table I. Samples were heated for a total of 80 hr at 900&apos;C in evacuated silica tubes, with one intermediate regrind-ing. The capsules were slow-cooled to room temperature in the furnace. Samples for X-ray diffraction were prepared by placing powder on a glass slide with vaseline. Dif- fractometer traces were obtained on a G.E. XRD-5 diffractometer using a chromium tube and vanadium filter (40 kv and 31 ma). The size of the spinel unit cell was determined from the eight highest angle peaks (80 deg < 2b < 160 deg). Calculated lattice parameters were plotted vs cos B . ctn 0 and extrapolated to 6 = 90 deg. Measurements of the magnetic susceptibility were carried out at room temperature using the Faraday method in a magnetic field of 3000 G and using a Cahn RG automatic microbalance. The system was calibrated from the well-established susceptibilities of platinum and palladium: (Xpt = 0.968 x 10-6 g-1 and Xpd 7 5.04 x 10~6 g-1). The weight of samples were approximately 0.200 g. X-ray diffraction patterns for unsintered mixtures showed Bragg peaks from both the spinel (CoCr2S4) and monoclinic (NiCr2S4) structures. After sintering no monoclinic peaks were observed in samples containing up to 40 mol pct NiCr2S4. However, the spinel peaks were displaced to higher angles with increasing

Jan 1, 1970

Discussion of the paper of Ralph Hayden, presented at the Butte meeting,. August, 1913, and printed in Bulletin No. 80, August, 1913, pp. 1443 to 1467. JOHN V. N. Done, Denver, Colo.:-Mr. Hayden has placed the metallurgical profession greatly in his debt .for this valuable paper. The importance of such a complete description of the research work on which is based the building of a plant to add at least 10,000,000 lb. of copper per year to the production of the Anaconda Copper Mining Co., at small expense, will be appreciated by all our members, and especially those who are facing similar problems. The information given in regard to the treatment methods discarded will be a great help to many workers, as it is often of as much importance to know what ? not to do" as what method to adopt. I Some further comment on the tests of the Dorr thickener may be of interest, as they have led to developments which I believe will prove of great importance. Before the Dorr thickener was installed, I had shown Mr. Laist reports from the Steptoe Valley concentrator, in which it was stated that one thickener 17 ft. in diameter was the equivalent in settling capacity of twelve 8-ft. cones, although the latter-contained double the surface area.. Mr. Laist, had made careful tests on the settling capacity of in 8-ft. cone on Anaconda slime, and we naturally expected the thickener would show a much higher capacity for equivalent area. When, is Mr. Hayden stated, the tests showed no increase, I realized that we were comparing it with a cone under test conditions, while the Steptoe results were based on operative conditions, find the explanation given by Mr. Waddell for the great difference had been, that " there is only one unit to watch instead of twelve, without the constant result of feed to twelve cones becoming unbalanced. Also the one 1 1/8-in. spigot used on the Dow requires no attention compared with the dozen 3/8-in. spigots of the cones.&apos; I realized also as a. result of the tests that the total settling area required to handle the immense tonnage of the Anaconda company would be enormous, and very expensive in view of the housing required by Montana climatic conditions. After studying the matter over, I told Mr. Laist that I believed a thickener operating in a much shallower tank would have nearly the same capacity. I asked him to test it out in the same tank filled 3 ft. deep, and stated that if my idea

Jan 11, 1913

Jan 2, 1951

By Robert B. Fulton

Staurolite, an iron aluminum silicate mineral, is used industrially as a high value-in-use sand-blasting agent, as a premium grade foundry sand, and as the source of aluminum in portland cement manufacture in areas where the aluminum constituent is not economically available from shale or argillaceous limestone. It is produced by E. I. du Pont de Nemours & Co. as a coproduct in titanium mineral production in Florida where it was first recovered on a commercial scale in June 1952 from the Pleistocene sand deposit known as Trail Ridge. In the Trail Ridge deposit it comprises about one-fifth of the heavy minerals, the principal other heavy mineral constituents being ilmenite, leucoxene, rutile, zircon, kyanite, sillimanite, and tourmaline. Staurolite and the other silicate nonconductive heavy minerals are separated from the conductive titanium minerals on high-tension separators. The silicates are then separated from one another magnetically, the staurolite being relatively magnetic. In the total processing, 200 tons of raw sand yield 7 tons of heavy mineral concentrate from which about one ton of staurolite is recovered. This process yields staurolite concentrates of the characteristics given in Table 1. These concentrates are sold as three products with the size distribution of subrounded particles shown in Table 2. All three grades are used in sand-blasting for cleaning metal, for paint removal, and for cleaning buildings. Staurolite compares favorably with lower unit cost abrasives, such as boiler slags and mineral aggregates, in applications where the abrasive is used only one time and is not recovered. Because it is hard, fine, clean, and dense it can reduce blasting time, with less material reportedly being required [ ]

Jan 1, 1983