Search Documents

By Nicholas J. Grant, Yoichi Ishida, Arthur W. Mullendore

An inert particle -marker technique was developed to provide a direct measurement of grain boundary sliding during creep in tile interior of aluminum specimens. Groin boundary sliding in the interior as measured by this technique was found to be nearly the same or slightly lower than that measured on the surface. These data disagree with those obtained by the grain-counting technique developed by W. A. Rachinger. In tests where both techniques were used, the grain-counting technique gave large and variable values of grain boundary sliding. It is shown that the grain-counting technique gines erroneozcs results because of a preferred direction of grain growth during creep. A question which has long plagued those who study grain boundary creep is whether or not surface measurements yield a true representation of the deformation in the interior of a specimen. The first attempt to measure grain boundary sliding in the interior of a creep specimen was made by Rachinger.1 His technique is based on the measurement of average grain diameters, both parallel and perpendicular to the tension axis, followed by a calculation of the grain elongation from these measurements. The difference between total elongation, Et, and the calculated grain elongation, Eg, is considered to be the result of grain boundary sliding, Egb. Surprisingly large values of Egb/ Et (90 pct) came out of creep tests of pure aluminum at temperatures above 250°C (480°F), utilizing the Rachinger technique. This value is very much larger than the values of 8 to 15 pct measured by numerous investigators on the surface of a specimen. Values obtained on the surface by Rachinger, however, were consistent with those measured by the displacement of reference scratches. Chaudhuri and Grant2 repeated the Rachinger method for A1-10 pct Zn, and found the same large values of Egb/Et inside the specimen. However, from purely geometrical considerations, grain boundaries cannot slide without grain deformation; therefore, they questioned the validity of Rachinger's grain-counting method. Several authors2,3 have suggested that grain boundary migration during high-temperature deforma- tion may tend to restore the equiaxed grain shape in order to minimize interfacial energy. Rachinger4 tested this hypothesis and found that it did not hold. Grains elongated by rapid extension retained their elongated shape during a subsequent slow creep test. It appears that some other factor was responsible for the abnormally high values of .Egb/El. McLean and Gifkins5 made a survey of the effect of grain size on the ratio Egb/ Et, and proposed that the high values were the consequence of a small grain size. They failed to explain the low value of Egb/Et which Rachinger observed on the surface of the small grain size specimens, and suggested that the surface effect on the value of Egb/Et does not always occur. Many of the disagreements arising from Rachinger' s work stem from the fact that there was only one method of estimating grain boundary sliding in the interior of a specimen, and that method was of an indirect nature. If a marker line of some sort could be introduced inside of the specimen, one could make measurements just as clearly as on the surface. In the present investigation, the technique utilizes a layer of finely dispersed oxide particles inside the specimen introduced by hot press-bonding of two pieces of aluminum. Rachinger attempted a similar technique but with the oxide distribution he obtained there was so much interference with grain boundary motion that quantitative measurements were not attempted. MATERIALS AND EXPERIMENTAL PROCEDURE A) Materials Preparation. Two pure aluminum rods (impurity content in percent: Si, 0.002; Cu, 0.004; Fe, 0.002; Mg, 0.000: Zn, 0.000; V. 0.001) 1 in. diameter by 2 in. high were jacketed end to end in a 4-in.-diam cylinder of commercial-purity aluminum, 4 in, high, which had a l-in.-diam hole. The l-in.-diam mating surfaces of the two pure aluminum rods had been electropolished initially. This interface provided the oxide-film internal -marker plane after the hot press-bonding process, see Fig. 2. The composite was annealed for 1 hr at 900 F and hot upset more than 50 pct reduction in height in one step. The resulting slab was then rolled to 1/2 in. thickness; the pure aluminum test material was cut out and annealed at 900°F for 1 hr and cold cross-rolled to 1/8 in. thickness. The sheet was machined into specimens with a 1/8-in.-square cross section and a 1/2-in. gage length. The following heat treatment was given the specimens: Specimen 5A series: annealed at 1000°F for 5 min for grain-size control and then cooled to 700°F and held for 15 hr for stabilization.

Jan 1, 1965

By B. R. Queneau

Steel has been chosen as the metal whose solidification will be used to tie in the principles discussed in the previous papers. Although steel is the most important [ ] practical example that could be chosen, its solidification is complicated by the presence of many elements added either intentionally or present as impurities. The liquid steel bath in an open-hearth furnace contains carbon, manganese, phosphorus, sulphur, and many residual alloying elements such as nickel, copper, and molybdenum. The bath also contains oxygen, the concentration of which is a function of the carbon content, as shown in Fig. I. Deoxidizers such as silicon and aluminum may be added either before or after tapping depending on the grade of steel being made. There are four types of steel ingots: Killed, semikilled, capped, and rimmed, and these differ from each other in their state of oxidation. Each type of steel has advantages in the production of specific steel products, and it should be emphasized that no one type should be considered superior to the others. Fully deoxidized steels, known as killed steels, have little or no gas evolution on solidification. When the steel solidifies in the mold, shrinkage occurs which causes a large void known as "pipe." To minimize the amount of metal that has to be discarded on account of pipe, a big-end-up mold is used together with a refractory "hot top" which supplies molten steel to the main body of the ingot while solidification proceeds, Fig. 2. A section through a 32x32 in. ingot is shown in Fig. 3. The "hot top" volume is about 15 pct of the ingot, and the yield from killed steel in billet form is about 8o pct of the ingot weight. High quality machinery and tool steels are rolled from killed-steel ingots, but at the present time this represents less than 20 pct of the total steel production in the United States. In order to reduce cost and to increase

Jan 1, 1951

By A. C. Heath, E. H. Dix

THE importance of aluminum-silicon alloys in the light alloy field is now generally recognized. Where silicon was once considered detrimental to the properties of aluminum, useful alloys now contain as much as 13 per cent. Furthermore, silicon is present as an impurity in aluminum of even the purest grades. Iron is another important impurity in aluminum and like silicon is found in small quantities in the purest aluminum available today. The manner of occurrence of iron and silicon in commercially pure aluminum and many of its alloys exerts a very pronounced influence upon their properties. The effect of large quantities of iron in aluminum-silicon alloys is so detrimental that it has been found necessary to limit the allowable maximum percentage to as low a figure as is consistent with quantity production and satisfactory physical properties. The intimate relation existing between iron and silicon in aluminum and aluminum alloys makes necessary a more complete knowledge of this ternary system. This paper is divided into two principal parts, dealing respectively with aluminum-silicon solubility equilibria and the constitution of aluminum-iron-silicon alloys. PART I.-ALUMINUM-SILICON ALLOYS The early work on this system was largely confined to determining the general form of the diagram and in this respect the results are in good agreement. Briefly, aluminum and silicon form a simple eutectiferous series without compounds. Until recently the solid solubility of silicon in aluminum had not been accurately determined. Fraenkel1 (1908) stated that aluminum will retain 0.5 per cent. silicon in solid solution. Rosenhain, Archbutt and Hanson2 gave the maximum solubility as about 1.50 per cent. and added that "this solubility does not appear

Jan 1, 1928

ALABAMA. Aldrich, Aldrich, W. F. Anniston, Noble, A. E Bessemer, Abbott, C. E., Fer¬gusson, V. Birmingham, Aldrich, T. H., Jr., Bowron, C. E., Bowron, J., Collord, G. L, Crockard, F. H., Davis, F. H, Dimmick, F. D., Hillman, Ludwig, C. P., McCarthy, M. E., McCormack, G B., McCrery, Ramsay, E., Shook, A. M. Car¬bon Hill, Pill, J. R. Coal City, Lydecker, I. S. Gannts Quarry, Hiller, E. Helena, Squire, J. Holt, Shook, J. \V. Huntsmlle, Moss. Lehigh, Toulmin. Oxmoor, Green¬amyer, A. G. Rock Run, Garvin, J. M. Sheffield, Miller, D. I. Woodward, Lodge, J., Woodward, A. H. ALASKA. Ellannar, Stevens, B. Fairbanks, Hamilton, A. L, Robe, L S. Hadley, John¬son, P. Jualin, Hoggatt, W. B. Juneau, Denby, Thane, B. L., Whipple, J. R. Katalla, Hampton, W. H. Ketchihan, Barber, J. C., Geiger, A. \V., Parker, J. L. Niblack, Finck, W. N., Niedling, B. B. Nome, Garfield, C. D. Tin Oity, Fay, A. H. Treadwell City, Kinzie, Stow, H. P. Valdez, Esterly, G. M., Hazelet.

Jan 1, 1910

By Cyril Smith

IN the study of the structure or the properties of a series of alloys or nonmetallic compounds, it is often advantageous to express the com-position not as percentage by weight, according to which the material is always made up and analyzed, but as the atomic percentage of the two constituents. The conversion from the one to the other is repre-sented by the formulas: 100A 100x Y x 100 ? x/A A [1] A+ B x + A/B(100-x) X _ 100yA 100y [2] yA+(100-y)B or y+A(100-y) where x and y are the weight and atomic percentages respectively of the element of atomic weight A, and (100 - x) and (100 - y) are the per-centages by weight and by atoms respectively of the element of atomic weight B. While calculations according to these formulas are simple, they are' time consuming if several conversions have to be made. In 1931 Water-man' constructed a nomograph for performing the conversion, but this did not permit an accuracy greater than about 1 per cent to be obtained in the neighborhood of 50 per cent. Olander2 has proposed a graphic method simpler than Waterman's and one that gives a uniform precision throughout the entire scale. The possible accuracy is about 0.5 per cent of the whole, depending on the size and accuracy of the coordinate paper used. Recently, Hermann3 has described a slide rule for making the calculations. These devices make use of the simple rearranged equation:

Jan 1, 1933

By Cyril Smith

IN the study of the structure or the properties of a series of alloys or nonmetallic compounds, it is often advantageous to express the com-position not as percentage by weight, according to which the material is always made up and analyzed, but as the atomic percentage of the two constituents. The conversion from the one to the other is repre-sented by the formulas: 100A 100x or 1 x/A+100-x/B B(100-x) _ 100yA 100y [2] X. yA + (100 - y)B or y (100 - y) where x and y are the weight and atomic percentages respectively of the element of atomic weight A, and (100 - x) and (100 - y) are the per-centages by weight and by atoms respectively of the element of atomic weight B. While calculations according to these formulas are simple, they are time consuming if several conversions have to be made. In 1931 Water-man1 constructed a nomograph for performing the conversion, but this did not permit an accuracy greater than about 1 per cent to be obtained in the neighborhood of 50 per cent. Ölander2 has proposed a graphic method simpler than Waterman's and one that gives a uniform precision throughout the entire scale. The possible accuracy is about 0.5 per cent of the whole, depending on the size and accuracy of the coordinate paper used. Recently, Hermann3 has described a slide rule for making the calculations. These devices make use of the simple rearranged equation

Jan 1, 1933

Featured at the 1977 SME-AIME Fall Meeting in St. Louis is a Lead-Zinc Update, organized to complement the 1970 AIME World Symposium on Mining and Metallurgy of Lead and Zinc, also held in St. Louis. The 21 papers comprising the Update are to be presented during four technical sessions at the Fall Meeting; in addition, the papers have been collected in a bound book available at meeting time.

Jan 9, 1977

By Henry M. Howe

Jan 1, 1908

By S. A. Allison, N. P. Finkelstein

After a brief consideration of the properties of zinc sulfide minerals, their flotation characteristics, and their reactions with thiol collectors, the literature on the activation of the minerals by cupric ion, their deactivation by cyanide, and their depression is reviewed in detail. The distinction between deactivation and depression is stressed. The contradictions in the published results and theories are discussed and attempts are made to resolve them. It is concluded that, whereas all aspects of the subject require further investigation, the study of depression is most likely to yield benefits in practice.

Jan 1, 1976

By Alexander L. Field

This paper contains an account of experimental results obtained in an extensive investigation of steels containing zirconium. There recently appeared' an announcement by F. M. Becket, at whose suggestion and under whose general direction this investigation was made, a statement of the outstanding features of the work and a brief explanation of the factors that led to its inception. It is not possible, in a paper of this character, to record all of the operating and test data collected, which includes the production of more than 350 heats of steel. The difficulty of a complete presentation is increased by the fact that several lines of experimentation are too incomplete to warrant publication of the results at the present time. In addition to the methods of manufacture and test employed in the work, there is described experimental evidence on which are based certain definite conclusions regarding the remarkable effects brought about by the presence in steel of relatively small percentages of zirconium. When added to a molten steel bath, zirconium combines chemically with dissolved oxygen, nitrogen, and sulfur, in the order named, and is capable of neutralizing the embrittling effect of phosphorus in whole or in part; although in the case of phosphorus there is no evidence so far of actual chemical combination. These effects arc not in the nature of suppositions supported by theory, nor is their existence deduced merely on the basis of analytical evidence. In each phase of its relation to or reaction with the four impurities mentioned, zirconium affects beneficiauy the mechanical properties of the steel to which it is added, in a manner which it is one of the purposes of this paper to explain in terms of a tentative working theory.

Jan 1, 1923

By Alexander L. Field

This paper contains an account of experimental results obtained in an extensive investigation of steels containing zirconium. There recently appeared' an announcement by F. M. Becket, at whose suggestion and under whose general direction this investigation was made, a statement of the outstanding features of the work and a brief explanation of the factors that led to its inception. It is not possible, in a paper of this character, to record all of the operating and test data collected, which includes the production of more than 350 heats of steel. The difficulty of a complete presentation is increased by the fact that several lines of experimentation are too incomplete to warrant publication of the results at the present time. In addition to the methods of manufacture and test employed in the work, there is described experimental evidence on which are based certain definite conclusions regarding the remarkable effects brought about by the presence in steel of relatively small percentages of zirconium. When added to a molten steel bath, zirconium combines chemically with dissolved oxygen, nitrogen, and sulfur, in the order named, and is capable of neutralizing the embrittling effect of phosphorus in whole or in part; although in the case of phosphorus there is no evidence so far of actual chemical combination. These effects arc not in the nature of suppositions supported by theory, nor is their existence deduced merely on the basis of analytical evidence. In each phase of its relation to or reaction with the four impurities mentioned, zirconium affects beneficiauy the mechanical properties of the steel to which it is added, in a manner which it is one of the purposes of this paper to explain in terms of a tentative working theory.

Jan 1, 1923

By Alfred Boyles

The experiments described below are a continuation of work on the graphitization of cast iron conducted as part of the program of fundamental research at Battelle Memorial Institute. In previous work it was found that melting in hydrogen increased the amount of eutectic carbide appearing in certain alloys and in others produced marked changes in the size of the graphite flakes. These effects seemed to be closely related to the amount of sulphur and manganese present in the material studied. Iron-carbon-silicon alloys did not respond to hydrogen in the same manner as cast iron and there was no evidence to show that hydrogen was able to stabilize the carbide in such alloys unless additions of sulphur were made. The two alloys examined contained about 2 per cent of silicon. The present paper is concerned with alloys of lower silicon content and describes the structural changes produced by melting in various atmospheres at pressurcs ranging from a partial vacuum up to 300 lb. per sq. inch. Experimental Method The experimental technique was similar to that previously employed, so that direct comparison might be made with earlier work. Alloys were

Jan 1, 1939

By Alfred Boyles

The experiments described below are a continuation of work on the graphitization of cast iron conducted as part of the program of fundamental research at Battelle Memorial Institute. In previous work it was found that melting in hydrogen increased the amount of eutectic carbide appearing in certain alloys and in others produced marked changes in the size of the graphite flakes. These effects seemed to be closely related to the amount of sulphur and manganese present in the material studied. Iron-carbon-silicon alloys did not respond to hydrogen in the same manner as cast iron and there was no evidence to show that hydrogen was able to stabilize the carbide in such alloys unless additions of sulphur were made. The two alloys examined contained about 2 per cent of silicon. The present paper is concerned with alloys of lower silicon content and describes the structural changes produced by melting in various atmospheres at pressurcs ranging from a partial vacuum up to 300 lb. per sq. inch. Experimental Method The experimental technique was similar to that previously employed, so that direct comparison might be made with earlier work. Alloys were

Jan 1, 1939

By W. H. A. Timm

Lake Dufault Mines, Limited, is located ten miles north of Noranda, Quebec, Canada. Following discovery of a copper-zinc orebody late in 1961, metallurgical investigations of diamond drill core were conducted by Lakefield Research Limited during 1962 and 1963. These were followed by pilot-plant tests in May and June of 1964, utilizing underground development ore. Milling operations commenced on August 16, 1964, and reached rated capacity of 1300 tpd by October 1, 1964. Since that time, tonnage was gradually increased to a maximum of 1400 tpd and since January 1, 1968, gradually decreased to the present rate of 1100 tpd due to an increase in the hardness of the ore. The ore milled from start-up until January 1968, was mainly massive sulfides, consisting of a complex mixture of iron, Copper, zinc, and minor amounts of lead sulfides with important associated values in gold, silver and cadmium (average specific gravity of 3-8). From January 1968 until the present, the ore being processed is described geologically as a boxwork of sulfide stringers of chalcopyrite, pyrite, and pyrrhotite with some local dissemination in siliceous rhyolite (average specific gravity 2.9) supplemented by the massive copper-zinc ore. The limited size of the orebody and the mining method employed (open stoping by blasthole and slash benching methods) would have

Jan 1, 1970

By H. Rumfelt

Strip mining in the domestic coal industry is contributing a greater proportion bf overall production than at any time in the past. U.S. Bureau of Mines statistics show that the percentage of total production mined in 1958 by stripping methods increased to more than 30 pct, up from 22 pct in 1951. The tendency to favor strip and open pit mining exists in other mining activities, but such trends are not as clearly outlined as in the coal industry. Significantly, the depth of overburden in coal properties considered suitable for stripping is also increasing. A depth of 50 to 60 ft of overburden was once considered to be about the maximum amount that could be handled economically. Today, a depth of 80 to 100 ft is frequently taken into consideration for simple overcasting operations (i.e., excavating overburden and dumping it in the spoil position where it remains indefinitely).

Jan 5, 1961

By Frank A. Herald

Through the generous cooperation of the authors of the papers in this chapter, a great wealth of fundamental data is being made available. The same plan of securing and submitting data will be carried forward next year, with the hope of making a nearer approach to complete presentation of the data contemplated in the plan. In order to conserve space, we are printing below such footnotes as have general application to Table 1 in the papers in this chapter: Footnotes to Column Headings Table I In areas where both oil and gas are produced, unless gas is marketed outside the field, such areas are included in column headed "Oil." Manufacture of casinghead gasoline and carbon black is interpreted as outside marketing of gas. Production per acre is determined by dividing into the number of barrels of oil the sum of the number of acres assigned to "Oil" plus such number of acres of the total assigned to "Oil and gas" as represents the portion thereof occupied by oil. Wells producing both oil and gas are classified as "Poducing oil only" unless gas from them is marketed off the lease. W. water; G. gas; A, air. Bottom-hole pressures are preceded by "e." All other figures represent pressures at casinghead with well closed. P, paraffin; A, asphalt; M, mixed. 0 Cam, Cambrian; Ord, Ordovician; Sil, Silurian; Dev, Devonian; Mis, Mississippian; MisL, Lower Mississippian; MisU, Upper Mississippian: Pen. Pennsylvanian; Per. Permian; Tri, Triassic; Jur. Jurassic; CreL, Lower Cretaceous; CreU. Upper Cretaceous; Eoc, Eocene; Olig, Oligocene; Mio. Miocene; Pli. Pliocene. 6, sandstone: SH, sandstone, shaly; Ss, soft sand; H, shale; L, limestone; LS, limestone. sandy; C, chalk; A, anhydrite; D, dolomite; Da. arkosic dolomite; GW, granite wash; P, serpentine. Figures are entered only for fields where the reservoir rock is of pore type. Figures represent, ratio of pore space to total volume of net reservoir rock expressed in per cent. "Par" indicates that the reservoir rock is of pore type but said ratio is not known by the author. "Cav" indicates that the reservoir rock is of cavernous type; "Fis," fissure type. A, anticline; AF, anticline with faulting as important feature; Af, anticline with faulting as minor feature; AM, accumulation due to both anticlinal and monoclinal structure; H, strata are horizontal or near horizontal; MF, monocline-fault; MU, monocline-unconformity; ML, monocline-lens; MC, monocline with accumulation due to change in character of stratum; MI, monocline with accumulation against igneous barrier; MUP, monocline with accumulation due to sealing at outcrop by asphalt; D, dome; Ds, salt dome; T, terrace; TF, terrace with faulting as important feature; N, nose; 9, syncline. Information will be found in text as indicated by symbols: A, name of author, other than above. who has compiled the data on the particular field; C, chemical treatment of wells; G, gas-oil ratios; P, proration; U, unit operation; R, references; W, water; 0. other information.

Jan 1, 1934

By W. A. Naismith, R. T. Pakalnis

The Umgal a section of the We1gedacht Exploration Company Ltd., a member of the Rand Mines Group, is situated near Utrecht in the province of Natal, South Africa. Two coal seams, the Alfred and Gus, are mined to fulfill commitments to both inland and export markets. To increase extraction in the high quality Alfred Seam, pillar extraction, known locally as stooping, was introduced to the mine in September, 1980. Mining is a conventional cut-drill -blast operation and takes place under a unique set of geological conditions viz. moderately thick seam at 3.5 m; rapidly varying cover from 25m to 120 m; an overburden containing competent sandstone and dolerite horizons. In order to improve the understanding of the manner in which the pillar and overburden interact during pillar extraction, a largely visual system of monitoring backed up by roof-floor convergence measurements was employed. Preliminary analysis of the observations suggests that roof collapse or goafing occurs in three phases but is only initiated once a critical amount of convergence has taken place.

Jan 1, 1983

By Allen F. Agnew

Detailed stratigraphic studies in the Wisconsin-Illinois-Iowa district have made it possible to map the folds and faults that controlled the deposition of the zinc-lead ore. Prospecting on the basis of this mapping and prospecting in lower zones that are potentially ore-bearing have led to discoveries of ore. GEOLOGIC studies for the Federal and State governments in the Wisconsin-Illinois-Iowa zinc-lead district were begun in 1835, and subsequent surveys were made in the three states at intervals until 1916, see Table I. The current study of the district, Fig. 1, by the U. S. Geological Survey was begun in 1942 in the hope that a systematic investigation would help increase production of zinc and lead, then in extremely short supply. Major emphasis of the USGS program was on detailed mapping of the geologic structure and ore deposits. Preliminary maps and reports covering localities of intensive mining activity have been published during the course of this study, Fig. 2. By 1950 the objectives of the study by the USGS were revised; 71/2-min quadrangles of relatively unprospected localities as well as intensively mined localities are now being mapped in Wisconsin. Since 1945 the investigation in Wisconsin has been made in cooperation with the Wisconsin Geological and Natural History Survey, and since 1951 the geologic mapping of areas of particular interest in Iowa has been performed in cooperation with the Iowa Geological Survey. At intervals since 1943 the Illinois State Geological Survey has mapped the geologic structure and ore deposits of localities in the Illinois part of the mining district, see Fig. 2. Geology was applied by mining company personnel as early as 1853, but only sporadically, with periods of greater application between 1890 and 1925. Much of the so-called geologic work was in reality mining engineering. Since 1946 the major mining companies in the district have employed geologists who have successfully applied geologic techniques in the search for ore. History of Mining Occurrence of galena in the district was known as early as 1658 or 1659, when French explorers heard of lead mines that were apparently in the vicinity of Dubuque, Iowa. In 1690 a trading post was established near Dubuque to obtain galena. The first significant attempt at mining by white men took place in 1788 when the Indians granted to Julien Dubuque mining rights for 20 miles along the west side of the Mississippi River, including the vicinity of Dubuque, Iowa. By 1805 lead was being mined near Galena, Ill. In 1819 permanent settlement of the region was begun, and most of the important lead-producing areas had been found by 1830, see Fig. 3. Lead production in the Wisconsin-Illinois-Iowa district between 1830 and 1871 far exceeded that of any other district in the U. S.' Smithsonite was first mined in 1859, and sphalerite was mined as early as 1867. After 1873 the production of sphalerite exceeded that of smithsonite. In 1873 annual zinc production from the district first equaled lead production, and from then until 1893 production of zinc and lead was roughly the same. Since 1893 the ratio of zinc to lead mined has generally ranged between 5:l and 20:l. In 1942 the Wisconsin-Illinois-Iowa zinc-lead district ranked 14th among zinc-producing districts of the U. S. From 1946 until February 1953 the dis-

Jan 1, 1956

By Louis Moyd

In the preparation of illustrations to accompany reports of investigations concerning particle shapes of various natural and manufactured materials proposed for use as he aggretates in concrete structures, it was found that stereoscopic views of such materials presented the information much more effectively than the usual two-dimensional photographs. With the whole-hearted cooperation of the Photographic Section, a technique was developed in the petro-graphic laboratory of the Concrete Research Division, U.S. Corps of Engineers, at Clinton, Miss., for simple and rapid preparation of paired stereoscopic photographs and micrographs. The method requires only equipment which is usually part of the general stock of any laboratory, and it is adaptable for all purposes in which three-dimensional views would be found superior to ordinary photographs. Stereoscopic Photographs Where the subject or subjects to be photographed are small but not of microscopic size, an ordinary camera having a ground-glass focusing screen is set up vertically over the field. The material to be photographed is placed on a card, the surface of which is suitable as a background. The card is mounted so that it can be tilted about 5' above and below the horizontal plane, on an axis that coincides with the north-south diameter of the viewing screen. A simple way of achieving this is to mount the card on an object having a convex lower surface. In our laboratory, a watch-glass has been used, with plasticene as the mounting medium. The convex surface should be mounted on a support having a round opening on top and a flat bottom. A roll of tape, a petri dish, a beaker, or any other piece of equipment having the proper shape to give stability to the setup will be satisfactory. The arrangement of the required equipment is shown in Fig 1. For the best results, the subject to be photographed should be mounted in the plane of the axis of rotation. To achieve this effect, the depth of the mass of plasticene between the background and the watch-glass is varied so that when the watch-glass is tilted back and forth on the axis, the subject to be photographed does not appear to move back and forth across the viewing screen. A permanent piece of equipment, embodying an adjustable vertical screw, with lock-nuts, could be made for this purpose. The subject may be illuminated in any manner desired. It was found that the presence of shadows intensifies the effect of depth. In taking the photographs, the concave surface is mounted so that one side of the background card is about 5' below the horizontal, while the axis remains in the horizontal plane. The subject is focused carefully on the ground glass and a picture is taken. The card is then tilted so that the opposite side is about 5' below the horizontal, while the axis still remains in the horizontal plane. The subject is again put in focus and another picture is taken. After both pictures are developed and printed, they are placed side by side in the same orientation and examined with a stereoscopic viewer. If depressions appear where there ought

Jan 1, 1950

By J. W. Pamplin

Some 40 miles east of Tampa is the center of the Florida pebble phosphate deposits. These are of Pliocene age and consist of several members of the Bone Valley formation.1 Physically the phosphate-bearing formation, locally called the "matrix," varies in thickness from nothing to about 25 ft., usually averages 10 ft., and consists mainly of clay, quartz and phosphate pebble, the latter particles varying in size from colloidal to one inch diameter. The pebbles range in color from dark gray, through white, to cream, and in hardness from that which must be broken with a hammer to that which can be scratched with the fingernail. They assay from 66 to 80 per cent bone phosphate of lime (called "B.P.L." in the trade) or tricalcium phosphate (Ca³P2O8) and are secondary apatites. They form from 15 to 50 per cent by weight of the matrix. Over the matrix lies a varying thickness (5 to 40 ft.) of overburden composed of quartz and clay. Briefly, mining consists of two operations2 in open pits about 200 ft. wide by 1/2 mile or more in length. In the first step overburden is removed by large electric draglines at the rate of about 700 cu. yd. per hour. This is followed closely by hydraulic mining of the matrix at the rate of about 300 cu. yd. per hour. This matrix yardage is moved from an improvised sump in the floor of the pit to an ore-dressing plant, sometimes a mile distant, by one, two or three "pit-cars" (pumping units) working on a 12-in. pipe line called the "rock line" to distinguish it from the high-pressure water line feeding the hydraulic giants, which is known as the "hydraulic line." This 700 yd. of overburden and 300 yd. of matrix—1000 yd. in all-amounts to about 1500 tons of material moved each hour. The overburden is dumped into the mined-out pit alongside the pit being mined. The matrix moves to the ore-dressing plant at the rate of about 7% long tons in 4000 gal. of water per minute—a ratio of approximately one to two by weight, or one to six by volume. This constitutes the "mill heads," but in the pebble district it is called the "matrix."

Jan 1, 1938