Search Documents

By Carl E. Swartz

In the course of a recent investigation1 to develop a more satisfactory white-metal bearing alloy, a number of alloy systems were studied. The cadmium-nickel system showed characteristics desirable in a bearing alloy, and the system was therefore studied in some detail. Experimental Method Alloying cadmium with nickel offered no serious difficulty. After melting the cadmium, clean sheet nickel was added while the temperature was maintained at 500" to 600" C. A few crystals of ammonium chloride2 served to clean the nickel when the latter did not "wet" readily. In preparing the individual alloys for thermal and microscopic investigation, a "hardener" containing about 10 per cent nickel was used. Thermal Experiments and Apparatus Time-temperature cooling curves were made by standard methods. Globe electrolytic cadmium was added to the hardener to make a melt of the desired composition weighing between 100 and 200 grams. This charge was placed in a Pyrex test tube, 1 by 10 in., closed with a rubber stopper carrying a thermocouple sheath and quartz stirring rod. The assembly was lowered to a depth of about 4½ in. into an electric resistance pot furnace containing a No. 0000 clay-graphite crucible (to catch the melt in case of a break in the test tube). After the tube was clamped in this position, an asbestos-magnesia mixture was loosely packed in the furnace around the tube and a "halved" cover of transite placed on top. This left at least 5 in. of the test tube protruding from the furnace. When the alloy had melted, the thermocouple was adjusted so that the hot junction was l! in. from the bottom of the test tube. The melt was stirred thoroughly for several minutes to insure composition homogeneity and absence of thermal gradients.

Jan 1, 1934

By C. E. Turner, J. R. Elenbaas, R. D. Grimm, J. A. Vary, D. L. Katz

A technique is presented by which well samples and core plugs of dolomite formations are classified by microscopic examination into seven different porosity grades. Quantitative values of porosity and permeability are determined for each grade by a statistical correlation of the core plug test data with the porosity grading system. These quantitative values are applied directly to the grades exhibited in the well samples for the purpose of estimating the reservoir void space for wells that were not cored. The procedure is described for estimating the gas reserves per unit area lor the South Hugoton gas field. but a reserve estimate for the field is not given. INTRODUCTION The miscroscopic examination of well sample; and the graphic recording of their lithologic qualities and other distinguishing characteristics of various geologic formations drilled is both a science and an art of long standing and wide application. Usually the primary objective of a geologist who "sits on the well" and examines the samples are: to identify the formation being drilled, determine the total depth, casing point. and completion interval. In most cases the porosity is described. if done at all, in general terms. such as: trace, scattered, fine, poor, fair, medium. good, excellent, or in some other relative terms. In fields where various geologists have examined samples and recorded observations on many wells considerable variations in lithologic terms and porosity descriptions occur unless there is primary effort to establish uniformity of logging observations and standards of recording observable porosity. When an estimate of the pore volume of a reservoir is made a geologic concept of the processes that control the magnitudes of porosity and permeability is developed by microscopic examination of well samples. The characeristics and appearances are then mentally related to rather general quantitative units of porosity based on physical core data from the same reservoir or on such data or experience in other reservoirs that have similar qualities. The reliability of such estimates depends largely on the variations of the lithology of the formations, the geometric properties of its void system. the extent of comparisons of sample appearances with porosity data, as well as the uniform recording of all relevant characteristics. This statement is particularly significant for dolo-mitized limestone formations of substantial thicknesses and heterogeneity such as the Permian Dolomites of the Hugoton gas field. Jn this field, as well as in most of the Permian Dolomite fields, the producing formations are of relatively great thicknesses in which the porosity and permeability of the reservoir varies substantially in all directions, depending on the crystalline structure. degree and kind of impurities, kind of fossils anti cementation thereof, degree of dissolution. and fracturing. The variations of the lithologic texture of the dolomites and post deposition alterations have resulted in porosities and permeabilities of such magnitudes that only a part of the gross thickness can be counted as "pay." At the time of this study insufficient gas production had been experienced to apply the pressure decline production method in the South Hugoton Field and the electric logs are not definitive enough. The problem of estimating gas reserves in the south part of the Hugoton Field is primarily one of determining the pay thickness and porosity from well samples and core data. The area studied embraced all that part of the field lying south of an east-west line through Guvmon, Okla., anti containing approximately 1.000,000 acres. This paper describes a technique of correlation of physical core data with well samples so that quantitative values of pay thickness, porosity. Permeability, and connate water may be assigned to well samples that are representative of a given interval, and thereby permitting the estimation of gas reserves lor a given unit area. The procedure was developed by a uniform microscopic qualitative porosity grading of the dolo. mite core plugs.. and relating these grades to the respective physical core data on a statistical basis The well sample-were also graded in a Similar manner in order that the quantitative values established lor the core plugs could be applied to the well Sample for wells that were not cored. GRADING OF DOLOMITE A group of experienced geologists was given the assignment of examining the samples on all wells in South Hugoton in order that they could log their observations in a uniform and standardized manner and grade the observed porosity so that it could be related quantitatively to the core data. The group initiated the study 011 chips from cores which bad been tested for porosity and permeability. This study continued until all of the geologists developed a common knowledge of lithologic terms and of the characteristic appearances of the samples and their relations to measured porosity. The characteristic appearances of the dolomite samples under twelve-power magnification as related to their qualitative porosities afforded a classification of the dolomite into :even grades of porosity, ranging from dolomite of no-visible porosity under twelve-power magnification to dolomite of excellent porosity. The assigned grade for a specific 10-ft interval is a weighted average of all visible grades of porosity exhibited by the cuttings representing that interval. The porosity characteristics were recorded by a color graph adjacent to the lithology column in conjunction with a numerical system for further definition of relative porosity as shown in Fig. 1. The three vertical lines to the right of the lithology column each represent 33 1/3 per cent. which lines were used to record the percentage of the samples, for any particular interval. that showed porosity under the microscope. The colors were used to denote actual pore size. i.e., orange. blue and I-ed for pore diameter of one-fourth or less. one-fourth to one-Ilalf. and greater than one-half millimeter, respectively. The area colored 1)). one or more colors represents the percentages of the samples exhibiting pores of the respective size or sizes. The numerals from one to six inclusive shown on the log in

Jan 1, 1952

By George C. Fryburg

The oxidation of platinum at high temperatures (above 800°C) is controlled by boundary-layer diffusion, except at the lowest pressures. The rate of oxidation is determined by the rate of diffusion of oxide through the boundary layer away from the platinum. This is in contrast to the situation in tungsten and molybdenum oxidation, where the rate is controlled largely by the diffusion of oxygen through the boundary layer towards the metal. The difference in mechanism is a consequence of the much lower rate of oxidation of platinum. Evidence is presented that supports this mechanism for the oxidation of platinum. SOME years ago we reported1 a study of the oxidation of platinum in ordinary oxygen in the temperature region above 800°C, where the oxide is volatile. All the data available up to that time had been obtained with platinum crucibles or plates heated in tube furnaces. The results were widely variant and highly dependent on the flow rate of gas through the furnace: the faster the gas flow rate, the higher the measured oxidation rate. These results indicated to us2 that reaction equilibrium was being approached in the furnace and that the rate was diffusion limited. To minimize these effects, we employed1 electrically heated ribbons placed in a cooled bulb. We were primarily interested in the low-pressure region, but some experiments were performed at pressures up to 1 atm. We found a peculiar pressure dependency which was explained on the basis that the rate of oxidation was proportional to the pressure at all pressures, but that with increasing pressure an increasing fraction of the volatilizing oxide was back-reflected to the ribbon by the surrounding gas molecules. The oxide molecules are not stable at the temperature of the platinum and are decomposed on impact, the platinum being re-deposited on the specimen. Because of the limitations of space, this explanation was offered summarily without detailed support. Recently, Jaffee and associates3, 4 have suggested that the pressure dependency of our data up to 0.5 torr could be explained on the basis of a Langmuir-type adsorption of molecular oxygen followed by dissociation. Since the correct explanation of the effect of pressure on the oxidation rate is a necessary requirement to the development of the basic mechanism of the oxidation reaction, we felt that the back-reflection theory should be presented in more detail. This is the object of the present paper. RESULTS AND DISCUSSION A typical set of results showing the pressure dependency of the oxidation reaction is presented in Fig. 1, where we have plotted, on logarithmic scales, the rate of oxidation, R, vs the pressure, p. For comparison some results of Krier and Jaffee4 and of Raub and plate5 are also shown. These data were taken at atmospheric pressure using furnaces. The effect of reaction equilibrium within the furnace is apparent from the much smaller values that these observers obtained: Raub and Plate In O2 found a rate of 3.1 µg cm-2 hr-1 compared to our value of

Jan 1, 1965

By M. R. Geer, H. F. Yancey

0. R. LYONS*—I know that we are all interested in hearing about problems that other people have. To most of the people from the eastern part of the United States, this kind of coal preparation is completely different. It represents washing difficulties that most operators have never experienced, or, if they have, they have refused to consider them because there are coals that are much easier to wash and, therefore. they leave the more difficult ones alone for the time being. E. R. McMILLAN†—I think the au-thors have summarized the material very well. Dr. Yancey has spent a great many years in the study of washing coals, as has Mr. Geer. I might comment briefly on some of the plants that were mentioned, plants with which I have had some con-nection, particularly those of our own company, the Northwestern Improve-ment Co. I would like to point out this: that ill each case, a great deal of work was done in the way of preliminary studies of washability of the coal before plants were built. The first plant of any size built in Roslyn field was mentioned in the paper. This central cleaning plant was designed and built to handle coal from three different mines. I might say that prior to 1935, the year in which the plant was built, the coal was used largely as railway fuel, close to a million tons annually. But as mining increased in depth, it became increasingly difficult to separate and gob much of the impurities underground, with the result that the run-of-mine coal became so high in ash that the railroad eventually was forced to consider installing some kind of preparation plant at the mine. We spent about a year in preliminary studies in cooperation with the Bureau of Mines to find out the best type of plant that would clean the coal. The result, as Mr. Geer has explained to you, is a rather complicated plant, but it is doing a very satisfactory job. We have, however, made a number of changes and improve-n~euts since it was first built. The last addition was the, installation of a cen- trifugal drier to dewater the minus ¼ in. size. We are now contemplating installing heat driers for further drying of minus ¼ in. We use Vissac heat driers for drying the stoker coal, the ¾ to in. The demand for drier coal, for both railway and industrial use, is forcing us to further drying of the coal. The plant that was mentioned as having been built in Pierce County, during the war, was a government sponsored plant. I happen to have had some connection with its design, construction and initial operation. We did what we thought then, and still think, was a very thorough job of preliminary studies in cooperation with the Burea of Mines of the coal from that field. The plant was as good a plant as could be built with the equipment available at that time, 1943. The plant that was mentioned as having been built at Ravensdale for treating the McKay coal was rebuilt about two years ago, and in addition to the modified Elmore jig washer that was mentioned. we added a coucentrating table for re-cleaning the minus 3/32 in. Our object there was to produce a commercial

Jan 1, 1950

By R. G. Garlick, M. Garfinkle

It was observed for several bcc metal crystals that the Knoop hardness anisotropy was dependent essentially on the direction of the lung axis of the indentor alone and not on the plane of indentation. The generality of this observation was tested for an fcc md an hcp metal and an ionic crystal. For cubic crystals, this observation was valid; for the hcp structure, however, the planes of indentation did have an effect on the hardness anisotropy, although this was not nearly as significant as the direction of indentation. Because the direction of indentation is the only significant crystal-lographic parameter necessary to describe the hardness anisotropy, it is possible to represent the anisotropy of single crystals on the standard stereographic triangle. THE commonly observed1, 2 periodic variation of indentation hardness with crystallographic direction on the high-symmetry planes of various single crystals has been inadequately related to the physical or mechanical properties of the crystals examined. In fact, the hardness anisotropy curves for the various planes of a particular metal crystal, as is illustrated in Fig. 1, are uncorrelated and appear in the literature3, 4 as unrelated observations. Attempts to correlate hardness anisotropy curves with specific physical properties can be generally divided into either mechanistic or nonmechanistic approaches. A nonmechanistic approach would be to devise a mathematical expression that could describe the various hardness anisotropy curves. Such a relation could then be compared with the known anisotropy of various physical properties to determine which contribute to the observed hardness anisotropy. No such mathematical expression has been found in the literature.

Jan 1, 1969

By K. R. Evans

The deformation mechanisms occurring in polycrys-talline, commercially pure titanium and a Ti-8 pct A1 alloy have been investigated and compared to earlier results by Levine on high-purity titanium single crystals and by Conrad on commercially pure titanium. In accord with Levine, two consecutive deformation mechanisms are observed to exist below 500°K with the transition temperature between mechanisms, Tc, strongly dependent upon interstitial composition. T, is found to be 210°. 375° -430°, and 450°K for alloys A large number of investigations have been conducted to determine the rate-controlling mechanisms of plastic deformation occurring in fcc and bcc metals. Very few investigations of a similar nature have been conducted for hexagonal metals. In fact, until very recently, magnesium is the only hexagonal metal which has been systematically investigated for determination of the rate-controlling deformation mechanisms.1"3 From these investigations, it was concluded that basal slip below 420°K occurs by the intersection of forest dislocations,1'3 while for prismatic slip the Peierls mechanism is rate-controlling at low temperatures with interstitial compositions of 0.024, 0.42, 0.61, and 1.13 at. pct expressed in terns of oxygen equivalents. The low-temperature mechanism is found to be an impurity obstacle mechanism in contrast to Levine's earlier conclusion of the Peierls barrier. Measurement of the activation parameters for deformation and estimation of the force-distance profile of the obstacles show their retarding force to be effective over longer distances from the obstacle as the interstitial composition increases. and thermally activated cross slip at higher temperatures. 2 The potential technological importance of titanium alloys has prompted recent studies of the deformation and fracture characteristics of titanium and its alloys. 4-8 Levine' systematically investigated the low-temperature deformation behavior of high purity titanium single crystals oriented for either basal or prismatic slip. It was concluded that the Peierls mechanism was rate-controlling at temperatures below 210°K, while above this temperature an undefined mechanism was rate-controlling. Conrad 7,8 concluded from an analysis of the composition dependence of the critical shear stress at 0°K and measurement of the activation parameters that the low-temperature deformation of titanium is controlled by an impurity

Jan 1, 1969

By C. Hanford Henderson

The belt of copper-bearing rocks of the South Mountain has attracted Attention principally iii the townships of Hamilton Ban and Liberty in Adams County, Pennsylvania, and in the southeastern portion of Franklin County. As the developments, thus far, have been almost exclusively limited to that area, the examination here described extended only within those boundaries. The region, being one of considerable interest geologically, has been the subject of careful study and description, both on the part

Jan 1, 1884

By Axel Hultgren, B. Herrlander

THE original aim of the present investigation was to study the mechanism of cracking on hot-deforming red-short steels. During the microscopical examination of hot-deformed soft steels attention was directed to various patterns of so-called veining in the ferrite, as related to variations in the deformation procedure and the heat-treatment of the steels. Later, a hot-short steel of higher carbon content was also studied. Historical Storey1 suggested in 1914 that veining developed during the gamma-alpha transformation from the growing together of several alpha nuclei within the same gamma grain. Rawdon and Berglund2 found that in soft steel, forged somewhat below A3, the ferrite showed profuse veining, while usually there was very little veining after forging at very high temperatures. They emphasized the similarity between the pattern of veining formed by deformation about 600°C and that of slip lines formed by deformation at room temperature. They also suggested a relation between the gamma-alpha transformation and veining. They became convinced from etching and from the slip-line pattern in cold-deformed material, that the orientation within any ferrite grain showing veining was uniform. In recrystallized alpha grains veining was absent. Veining did not appear materially to affect the properties of ferrite. Independent of veining, continuous networks, attributed to preexisting delta and gamma grain boundaries were sometimes found, the former only in cast steel. Those networks were usually connected with small inclusions. Ammermann and Kornfeld3 confirmed that recrystallized ferrite grains showed no veining. In soft steel annealed between At and A3 there was veining only in the ferrite grains formed during cooling. Electrolytic iron deformed at 880° was free from veining. Bannister and Jones4 considered veining in ferrite to be a manifestation of microscopical and submicroscopical inclusions. Northcott,5,6 in studies on veining in steel and other metals and alloys, attributed veining to oxide inclusions. It could generally be removed by annealing in hydrogen, a suggestion earlier made by Rawdon and Berglund. Tritton (discussion in ref. 5) emphasized the importance of perfect polishing for bringing out veining by etching, and thought the veins or subboundaries were produced during the gamma-alpha transformation, when it was rapid, as a result of the volume change and contraction during cooling.

Jan 1, 1946

By Edward H. Robie

PONCA CITY proved an ideal selection as a place of meeting for the Petroleum Division this fall. The accommodations at the Conoco Club were just what was required for such a gathering; the committee having the arrangements in charge functioned with the efficiency of veterans and the enthusiasm of neophytes; and the members and guests followed the speakers with close attention, entered the subsequent discussions with gusto, and divulged the "low-down" at private conferences. No one minded the drizzling rain on the first day, which only served to keep up the attendance in the auditorium; the weather then cleared up in time for a group picture before the gathering went their separate ways.

Jan 1, 1932

By H. W. Paxton, C. C. Busby

IT has been shown previously' that strain aging can markedly improve the tensile properties of low carbon martensites, especially the yield-tensile ratio, without seriously affecting the ductility. In view of interest in high strength steels, an investigation has been made of the effect of strain aging following tension or rolling on the tensile properties of A1S1 4340 in an attempt to obtain a tensile

Jan 1, 1957

By J. C. Shyne, T. D. Gulden

The steady-state creep behavior, in compression, of indium containing a dispersion of atomized glass particles was studzed over a range of temperature, stress, and composition. The observed behavior was not consistent with a simple model of dislocation climb over dispersed particles. From room temperature to about 100°C the temperature dependence could be described by an activation energy about one and a half times that of self-dijfusion in indium while at higher temperatures a much higher ternperature dependence was observed. THE value of dispersion-hardened and precipitation-hardened alloys has long been recognized. The mechanism of hardening, however, is not completely understood, especially at elevated temperatures where dispersed particles increase creep resistance. Following the suggestion of Schoeck1 that the rate of creep in dispersion-hardened materials is controlled by dislocation climb over second-phase particles, Ansel and weertman2 derived steady-state creep equations for dispersion-hardened materials. Their derivation was based on dislocation climb over non-deformable spherical particles in a metallic matrix. For low stresses they predicted a linear relation between applied stress and steady-state creep rate. For stresses large enough to cause dislocations to pinch off around the precipitate particles, the theoretical creep rate was shown to be proportional to the fourth power of stress. For very high stresses an exponential stress dependence was predicted. In all cases the theoretical creep rate is linearly proportional to the diffusion coefficient. This provided the primary temperature-dependent factor. Subsequently, Ansel and Lenel3 reported some experimental data on SAP, a composite of aluminum and aluminum oxide, that was in good qualitative agreement with the above theories. Their experimental creep rates, however, were four orders of magnitude less than the theory predicts. This was attributed to a low density of active dislocation sources in the material; somehow the dispersed particles inactivated the dislocation sources instead of merely interferring with dislocation motion. Meyers and sherby4 have recently reported on the creep behavior of SAP. Their results were inconsistent with a simple dispersion-strengthening model and led them to conclude that a continuous network of oxide controls the high-temperature mechanical characteristics of SAP. Because of the rather complex mechanical behavior of SAP and the lack of agreement about the morphology of its oxide phase, it appeared desirable to study the creep of a dispersion-strengthened material of controlled morphology. For the present work a dispersion of spherical glass particles imbedded in a matrix of indium was chosen. The microstructure of this material was similar to the idealized uniform dispersion of hard spheres in a deforming matrix assumed by Ansel and Weertman in their theoretical treatment. SPECIMEN PREPARATION For experimental convenience, it was decided to use a low melting-point metal in this investigation. It was necessary that the metal not be oxidized readily up to its melting temperature and that it wet the second-phase particles. It was desired that the material chosen for the dispersed phase be available as a fine powder with closely controlled size and shape. The material chosen to satisfy these requirements consisted of a matrix of indium metal containing a dispersion of atomized particles of a soft soda-lime-silica glass ranging from 5 to 30 µ in diam. The glass particles had a highly regular spherical shape. The composite was made by stirring the glass powder into liquid indium maintained at a temperature just above the melting point of indium, 156°C. The creep specimens were prepared by a hot pressing operation. Five to ten g of the mixture were placed in a steel die and pressed at 125°C for 5 min under a pressure of 30,000 psi. The resulting specimens were cylinders about 3/8 in. in diam and ranged from 0.4 to 0.7 in. high. By following this procedure a uniform dispersion was obtained in the creep specimens. Typical microstructures of specimens containing twenty and forty volume percent glass powder are shown in Figs. 1 and 2. Unfortunately, grain size could not be determined by the metallo-graphic techniques used. CREEP TESTING PROCEDURE Creep tests were performed in compression under constant stress. The specimens were placed in

Jan 1, 1963

By Arthur Tauber, Horst Kedesdy

FERRITES are sintered metallic oxides of the spinel structure type1 and belong to the class of soft ferromagnetic materials. Similar to a ceramic, they can be formed and fired to a dense body, exhibiting a high electrical volume resistivity ranging from 102 to 102 ohm-cm as compared with 10-6 ohmcm for some of the metallic magnetic materials. This high resistivity, with resulting low eddy current losses, finds special application at high frequencies. The dispersive susceptibility of ferrites at microwave frequencies has also led to many applications in this field. Where high resistivity with high permeability is desirable, ferrites are used in low frequency applications. During the last few years ferrites exhibiting rectangular hysteresis loops have been developed for computer and magnetic memory systems. The general formula for ferrites is MeFe2O4 where Me is a divalent metal ion such as Ni, Zn, Mg, Mn, Cu, Cd, and Fe. Only two of these ferrites are nonferromagnetic, namely, those with Zn and Cd. Solid solutions can be formed between different ferrites, and it is of interest to note that solid solutions of a ferromagnetic ferrite with a nonferromagnetic ferrite yield much better magnetic materials than the basic ferrite body. In general, it can be said that the solid solution formation between ferrites has widened the field of ferrite synthesis and has led to methods of preparing materials with a large variety of magnetic properties.

Jan 7, 1957

By H. William Ahrenholz

Many technical meetings were attended by mining people during the past year in which rock mechanics was either the main subject for discussion or was a prominent part of the program. Several universities continued to offer short courses in the applications of rock mechanics for practicing mining engineers. At the beginning of the year, the AIME Committee on Rock Mechanics achieved standing-committee status. It is to assume responsibility for coordinating all AIME activities in this area. Eleven professional societies are now participating in a newly formed Intersociety Committee for Rock Mechanics. AIME and its constituent societies has three representatives. Delegates from the Intersociety Committee will serve on the U.S. National Committee for Rock Mechanics which is being formed by the national Academy of Sciences.

Jan 2, 1967

By JOHN R. SUMAN

COMMENCEMENT exercises this year have a peculiar significance because the graduating students are entering upon their life's work at the most critical time in the history of the United States. We are engaged in a great struggle the outcome of which is none too clear even to the best informed students of international affairs. We are starting late in a vicious world conflict where it is generally recognized that our adversaries have distinct superiority over us in armament on the land, on the sea, and in the air. We have the gigantic task of building up our armed forces and armament and at the same time supplying our allies with equipment which they must have. We can do this job if we are given sufficient time, but there is a possibility that the war will be over before we are ready. Few realize the seriousness of this situation. If this fight is to be won-and we dare not try to visualize the future of this country if it is lost-all dissension and bickering between Congress, capital, labor, and agriculture must cease. When and where voluntary co-operation proves inadequate for the successful conduct of the war effort, laws must be enacted or strengthened to achieve our purpose.

Jan 1, 1942

By C. W. Macgregor

The observation of the flow layers, or Luders' lines, produced in mild steel when it is stressed into the plastic range often provides considerable useful information for the study of the fundamental mechanism of the plastic flow of metals. It is a commonly observed fact that as soon as the upper yield point in a mild-st'eel tensile-test bar is passed, an unstable condition develops in the equilibrium, the load on the testing machine drops and if the surface of the bar contains a thin mill scale, the latter begins to flake off rapidly along certain "lines." These "lines" are ill reality traces of wedge-shaped flow layers and are formed by the inter-section of the surface of slip and the surface of the bar. The average plane of the flow layer itself has been found by various experimenters to be inclined at an angle of approximately 45" to the axis of the test bar. In a body of more complicated shape stressed in possibly a different man-ncr, the tangent planes to the flow layers at each point seem in many cases to be inclined at an angle of about 45" to the principal stress direct-tions at the point. As examples of the latter may be mentionecl the logarithmic spirals obtained when a rivet hole is punched in a thin plate, or when a tube is subject,ed to internal pressure only, etc. IIencc if the flow layers are observed from an experiment, the shear-st'ress trajectories —the curves indicating the direct,ions of the maximum shearing stresses in the body—may then be approximately determined. Since the latter curves form an orthogonal family inclined at 45" to the principal stress directions, the family of principal stress trajectories, or the curves irldicating the directions of the principal stresses, may be thus obtained Although the discontinuous type of stress-strain curve at the yield point is commonly observed with test bars of mild steel, more recent experiments have shown that this is by no means the only material exhibiting this interesting phenomenon. A similar effect has been observed in zinc and cadmium crystals, by Becker and Orowai~; in duralumin and other aluminum alloys, by Dawidenkow,~Elam,~ Fell4 an(l others; in copper and copper-alloy crystals, by Elam;~ in brass by Elam;3 in brass wires by deForest;" in higher carbon steels, tungsten steel, and

Jan 1, 1939

By C. W. MacGregor

The observation of the flow layers, or Luders' lines, produced in mild steel when it is stressed into the plastic range often provides considerable useful information for the study of the fundamental mechanism of the plastic flow of metals. It is a commonly observed fact that as soon as the upper yield point in a mild-st'eel tensile-test bar is passed, an unstable condition develops in the equilibrium, the load on the testing machine drops and if the surface of the bar contains a thin mill scale, the latter begins to flake off rapidly along certain "lines." These "lines" are ill reality traces of wedge-shaped flow layers and are formed by the inter-section of the surface of slip and the surface of the bar. The average plane of the flow layer itself has been found by various experimenters to be inclined at an angle of approximately 45" to the axis of the test bar. In a body of more complicated shape stressed in possibly a different man-ncr, the tangent planes to the flow layers at each point seem in many cases to be inclined at an angle of about 45" to the principal stress direct-tions at the point. As examples of the latter may be mentionecl the logarithmic spirals obtained when a rivet hole is punched in a thin plate, or when a tube is subject,ed to internal pressure only, etc. IIencc if the flow layers are observed from an experiment, the shear-st'ress trajectories —the curves indicating the direct,ions of the maximum shearing stresses in the body—may then be approximately determined. Since the latter curves form an orthogonal family inclined at 45" to the principal stress directions, the family of principal stress trajectories, or the curves irldicating the directions of the principal stresses, may be thus obtained Although the discontinuous type of stress-strain curve at the yield point is commonly observed with test bars of mild steel, more recent experiments have shown that this is by no means the only material exhibiting this interesting phenomenon. A similar effect has been observed in zinc and cadmium crystals, by Becker and Orowai~; in duralumin and other aluminum alloys, by Dawidenkow,~Elam,~ Fell4 an(l others; in copper and copper-alloy crystals, by Elam;~ in brass by Elam;3 in brass wires by deForest;" in higher carbon steels, tungsten steel, and

Jan 1, 1939

By Parke A. Dickey

Potential differences between strata of shale and sandstone have been recognized for about 15 years, and they form the basis of the electrical logging of oil wells. Hitherto these potentials have been ascribed solely to electro-¦ chemical reactions caused by the disturbing effects of the water in the drill hole through which they are generally measured. Observations by the author in wells empty of water and in a mine shaft suggest that potential differences between sandstones and shales are natural and specific properties of the rocks, although they are moditied in measurement by the disturbing effects of the water in the drill hole. The cause of these potentials probably is to be sought in the relative polar adsorptive capacities of quartz and clay particles. Introduction The existence of potential differences in the surface of the earth has been known for some time, and their measurement has facilitated the discovery of geological discontinuities such as ore bodies. The technique of measurement has been well established.1-3 In measurements in oil wells, it has been found that the potential of shales with respect to some arbitrary reference is very nearly constant in any one well, at least below the zone to which meteoric water has gained access. Sandstones and some other types of sedimentary rocks have a difference of potential with respect to shale that is negative arid may attain a value of 200 millivolts or more. The difference of potential, as usually measured commercially with water in the hole, is distributed over about one foot vertically at the top and bottom contacts of the sandstones. The sharpness of the curve at the formation contacts can be improved by using a short electrode that is close to the wall of the hole' These potentials generally have been ascribed to the disturbing effects of the water in the drill hole. Potentials have been found, however, in wells in which no water was present. In the course of experiments in electrical logging in pennsylvania, carried out by the pennsylvania Geological Survey, observations were made of several phenomena that hitherto have not been described, to the author's knowledge, ill the published literature. The potential differences across the contacts of sandstone and shale are called ill this paper "natural potentials," as distinguished from the potentials caused by electroendosmosis (electrofiltration) and concentration differences, which will be discussed subsequently. Potentials in Cored WeLl In the spring of 1942, the author measured the potentials in an exploratory well (Day 13, near Grand Valley, Pa.) which had been cored With diamond tools. The potentials were first measured with fresh water in the hole. * null balance potentiometer was used in this and all the other measurements described in this paper. One nonpolarizing porous pot electrode, containing copper sulphate solution and

Jan 1, 1946

By Parke A. Dickey

Potential differences between strata of shale and sandstone have been recognized for about 15 years, and they form the basis of the electrical logging of oil wells. Hitherto these potentials have been ascribed solely to electro-¦ chemical reactions caused by the disturbing effects of the water in the drill hole through which they are generally measured. Observations by the author in wells empty of water and in a mine shaft suggest that potential differences between sandstones and shales are natural and specific properties of the rocks, although they are moditied in measurement by the disturbing effects of the water in the drill hole. The cause of these potentials probably is to be sought in the relative polar adsorptive capacities of quartz and clay particles. Introduction The existence of potential differences in the surface of the earth has been known for some time, and their measurement has facilitated the discovery of geological discontinuities such as ore bodies. The technique of measurement has been well established.1-3 In measurements in oil wells, it has been found that the potential of shales with respect to some arbitrary reference is very nearly constant in any one well, at least below the zone to which meteoric water has gained access. Sandstones and some other types of sedimentary rocks have a difference of potential with respect to shale that is negative arid may attain a value of 200 millivolts or more. The difference of potential, as usually measured commercially with water in the hole, is distributed over about one foot vertically at the top and bottom contacts of the sandstones. The sharpness of the curve at the formation contacts can be improved by using a short electrode that is close to the wall of the hole' These potentials generally have been ascribed to the disturbing effects of the water in the drill hole. Potentials have been found, however, in wells in which no water was present. In the course of experiments in electrical logging in pennsylvania, carried out by the pennsylvania Geological Survey, observations were made of several phenomena that hitherto have not been described, to the author's knowledge, ill the published literature. The potential differences across the contacts of sandstone and shale are called ill this paper "natural potentials," as distinguished from the potentials caused by electroendosmosis (electrofiltration) and concentration differences, which will be discussed subsequently. Potentials in Cored WeLl In the spring of 1942, the author measured the potentials in an exploratory well (Day 13, near Grand Valley, Pa.) which had been cored With diamond tools. The potentials were first measured with fresh water in the hole. * null balance potentiometer was used in this and all the other measurements described in this paper. One nonpolarizing porous pot electrode, containing copper sulphate solution and

Jan 1, 1946

By James J. Bailey

Percussive drills have been in commercial use for many decades. Until relatively recently there was little serious effort to analyze the stresses in such devices in any detail. Within the last few years such analyses have been developed and have been reported by a number of authors.1-4 We present here an investigation of the impact systems of a family of conventional down-hole drills with optimization the objective. We have assumed that maximum drilling speed was the quality most desired and that this was to be achieved within conventional practice. In fact the methods that are demonstrated in principle below can readily be adapted to other percussive devices, whether conventional or not, and to other constraints. SOME PERFORMANCE PARAMETERS FOR PERCUSSIVE DRILLS Consider a percussive drill with an air motor operating with the following parameters: p-supply air pressure a-effective piston area W-piston mass S-piston stroke If we consider a simple (constant pressure) cycle, the following relationships can be derived. The blow frequency [N~ pa lie WS 377]

Jan 1, 1968

By W. H. Emmons

This paper is the third of a series treating of the relations of ores of the metals to igneous rocks. The first' outlined the general problem; the second2 proposed a classification of lode ores, and showed how the distribution of the deposits is in a certain measure controlled by the contour of the roof of the parent batholith. A number of mining districts were discussed, the examples being selected chiefly from group 2 of the classification. The proposed classification of lode deposits, briefly stated, is as follows: 1. Cryptobatholithic: near hidden batholiths which have not yet been exhumed by erosion. 2. Acrobatholithic: in and near cupolas or domes of batholiths—the high points of larger underlying masses. 3. Epibatholithic: on batholiths, near their rims, but below eroded cupolas, or below the highest points of the roofs. 4. Embatholithic: among closely-spaced outcrops which probably are parts of a single bathohth. The outcrops of invaded rocks predominate. 5. Endobatholithic. in and near roof pendants of large batholiths. The invading rocks predominate. 6. Hypobatholithic: in deeply-eroded batholiths, where even roof pendants have been eroded. Deposits of certain metals on the roofs of the batholiths are much more numerous in some positions than deposits of other metals, and the horizontal zonal arrangements of lodes of different metals are shown characteristically only in certain groups. In a large measure, also, the character of the fracturing and metallization is determined by the position on the roof of the batholith. The disseminated copper ores in porphyry constitute a clearly-defined type. All the deposits of these ores, as far as known, are in group 2. They appear to have been formed only in and around small upward projections of the parent granitic masses, and not low on the walls of the

Jan 1, 1927