Search Documents

By Enid C. Plante

To extend our knowledge of the flotation behavior of sulphide minerals, the response of the following minerals to ethyl xanthate as collector was studied by captive bubble and cylinder flotation tests: antimonite (Sb2S3), arsenopyrite (FeAsS), covellite (CuS), rnarcasite (FeS2), orpiment (As&.), pyrrhotite (FeS) and tetrahedrite (4CU2S, Sb2S3). Lollingite (FeAs2) was also exarnined to determine if its behavior could be correlated with that of pyrite or rnarcasite (FeS2. Experimental Method Mineral for Flolation and Contact Tests Mineral was prepared in the manner a1ready described1 and its behavior both freshly ground and "oxidized" was studied. Tests in which the mineral was allowed to oxidize for various periods showed that a uniform response to xanthate was reached in two days or less. Oxidation Products The soluble oxidation products from most of the above minerals were measured and their effect on the flotation of the mineral studied. The mineral samples were wet ground to minus-52 mesh and deslimed, and 20 g of this material placed in 200 ml of distilled water of a measured pH value, and CO2-free air bubbled through each suspension at a constant rate (about I bubble/sec) for 5 days. It has been shown1 that the size of the mineral is unimportant in the rate of formation , oxidation products and that probably the supply of oxygen to the mineral is the rate-determining step. At the end of 5 days the pH value of the 'supernatant liquid was measured again, the mineral filtered off and the soluble products determined. Methods for estimation of sulphur acids, ferrous and ferric iron and copper have already been described.l No satisfactory method was found for antimony. Arsenic was estimated as the arsenate.2 Flotation of "Unoxidized" Minerals with Ethyl Xanthate as Collector Fig I to 3, 4. 6, show the effect of alkali and cyanide as depressants for the minerals with 25 mg potassium ethyl xanthate per liter as collector at 35°C. Wark and Cox8 have shown that with ethyl xanthate as collector, galena, pyrite and chalcopyrite show a greater tolerance to cyanide and hydroxyl ions at room temperature than at 35°C Covellite (Fig I), marcasite (Fig 2) and pyrrhotite (Fig 3) behave similarly. The independence of the curves for pyrrhotite at 35°C with respect to cyanide

Jan 1, 1949

By H. Kenyon Burch

INTRODUCTION THE Inspiration Consolidated Copper Co.'s plant at Miami, Ariz., was designed and built to make possible the profitable working of a low-grade, finely disseminated copper deposit containing 100,000,000 tons of ore averaging 1.64 per cent. in copper. From the-beginning it was evident that the-plant could not, be kept integral but that a break would have to be made somewhere in the flow-sheet, removing at least the concentrator to a site more suitable than any available near the mine. It was finally decided, after considering numerous arrangements, to do the coarse crushing at the mine, to store the crushed ore in a bin from which it could be loaded into railroad cars and to haul it to the concentrator, an excellent site for which was available about 1 ¾ miles from the mine. The original intention was to equip a plant to treat 7,500 tons of ore per clay, but through the acquisition and proving up of additional ore reserves, the introduction of the Ohio caving system, and the excellent results obtained in the test mill (which made it possible to treat a lower-grade ore than had been thought possible) it was evident that a plant of much greater capacity should be supplied. It was, therefore, decided to treat approximately 15,000 tons of ore per day, the duties of the four main divisions to be as follows:

Jan 9, 1916

By A. J. Lena, M. F. Hawkes

Changes in hardness, tensile properties, microstructure, electrical resistance, and X-ray diffraction effects indicate that lattice strains are necessary for the embrittlement of ferritic stainless steels when heated for relatively short times at 475°C (885°F). It is suggested that 475°C (885°F) embrittlement is due to the accelerated formation of an intermediate stage in the formation of s under the influence of these strains. FERRITIC stainless steels (low carbon alloys of iron with more than 15 pct Cr) are subject to two forms of embrittlement when heated in the temperature range of 375° to 750°C. The embrittlement which occurs after long time heating between 565" and 750°C is well understood; it is caused by the precipitation of the hard, brittle s phase. Sigma is an intermetallic compound of approximate equi-atomic composition with an extended range of formation in Fe-Cr alloys. The maximum temperature at which this form of embrittlement can occur is dependent upon chromium content; and is approximately 620°C for a 17 pct Cr steel and 730°C for a 27 pct Cr steel. The other form of embrittlement occurs after relatively short heating periods in the range of 375" to 565°C; in the higher chromium steels, hours may be sufficient as compared to months for s embrittlement. This phenomenon is not at all well understood and several controversial theories have been proposed. The rate and intensity of embrittlement increase with increasing chromium content but the maximum rate occurs at 475°C re-gardless of chromium content. As a result of this, the phenomenon has been termed 475°C (885°F) embrittlement. The effect of 475°C embrittlement on the properties of ferritic stainless steels has been thoroughly reviewed by Heger.1 The embrittlement causes a pronounced decrease in room temperature impact strength and ductility, a large increase in hardness and tensile strength, and a decrease in electrical resistivity and corrosion resistance. Microstructural changes accompanying embrittlement are minor and difficult to interpret with a general grain darkening, appearance of a lamellar precipitate, grain boundary widening, and precipitation along ferrite veins having been reported at various times. With the exception of reported line broadening, X-ray diffraction studies by conventional Debye analysis of solid samples have been of little value. BY making use of electron diffraction methods, Fisher, Dulis, and Car-roll' have recently shown the existence of a chromi-um-rich, body-centered cubic phase in 27 pct Cr steels which had been aged at 482°C (900°F) for as long as four years. Two types of theories have been advanced to account for the embrittlement. The first of these requires the precipitation of a phase not inherent in the Fe-Cr system with various investigators suggesting a carbide,3 nitride,3 phosphide,4 or oxide." Theories of this type have difficulty accounting for the influence of alloying elements on the embrittlement and for the facts that a minimum chromium content is necessary for embrittlement and the intensity of embrittlement increases with increasing chromium content. The second type of theory that has been proposed relates 475°C embrittlement to s phase formation which is inherent in the Fe-Cr system. An assumption of this kind can adequately explain the influence of alloying elements, for they exert an effect on 475°C embrittlement similar to that on s phase for-mation as can be seen in Table I. The minimum chromium content is essentially the same for both phenomena and it has been shown12,13 that s is a stable phase in the embrittling temperature range. In addition, it has been reported14,15 that pure alloys embrittle to the same extent as commercial type alloys. There are, however, several factors which have prevented complete acceptance of a s phase theory. Foremost of these is that the embrittlement can be removed by reheating for short time periods above 600°C, which in the higher chromium steels is within the stable s region. No s has ever been observed after one of these curing treatments, nor has any s been found as a result of embrittlement at 475°C. In addition, the simple precipitation of s cannot explain the time-temperature relationships for reactions between 350°and 750°C. This behavior is shown schematically in Fig. 1. Newell 16 and Ried-rich and Loib4 have shown that 475°C embrittlement follows a C-type curve as illustrated, while Short-

Jan 1, 1955

By T. E. Kihlgren

SYSTEMATIC data are presented on the relation of composition of nickel silvers to color, tarnish resistance, hardness and liquidus temperatures, for alloys containing up to 30 per cent nickel and 50 per cent zinc, further modified at certain nickel and zinc contents by 0 to 8 per cent of tin and 0 to 10 per cent of lead. Attention has also been directed, using a still more limited range of alloys, toward a study of tensile properties and such casting properties and characteristics as fluidity, shrinkage and pressure tightness. In some of these, rather broad ranges of composition are dealt with; in others, it has been expedient to focus attention on the Federal Specification 20 per cent nickel silver casting alloy, WWP-541. INTRODUCTION The demand for an alloy essentially white in color, which could be cast and worked by simple methods and which possessed strength and corrosion-resisting properties superior to the usual brasses, led to the discovery and early use of cupronickel alloys containing zinc, and some-times tin, lead and other metals. This type of alloy was generally known as German silver until the war, when the term "Nickel Silver" became generally accepted. The element principally responsible for the white color of the alloy and for its strength and corrosion resistance is nickel, which may constitute from 8 to 30 per cent of the alloy. The functions of the other elements will be described later. The manifold uses of nickel silver are largely due to its color, corrosion resistance, ease of casting, fabrication, joining and rather moderate cost. In many instances the alloy is finished by grinding and polishing while in others it may be finished with a silver or nickel plus chromium plate. Electroplates

Jan 1, 1935

By Holbrook G. Botset

It is possible by means of the electrolytic model to simulate water-flooding or gas recycling systems involving input and output wells, and also the encroachment of a natural water drive. The results are obtained pic-torially, and by simple measurements and calculations the percentage of recovery is obtained qualitatively as a function of the total input. Introduction The increased demand for petroleum products, together with the decline in discovery rate and the higher cost of recovery as deeper formations are brought into production, has stimulated interest in methods for studying and predicting efficiencies of various production programs. Among methods Of recovery that have become of increased significance recently are gas recycling in condensate fields and secondary recovery by water-flooding. The electrolytic model is a useful device for studying such methods in the laboratory, at least in a qualitative way. The original experiments with electrolytic models and the development of their application to the study of secondary reCoverY problems were published in 1933. 1,2,3 Subsequently other investigators continued the development and modification of the bait method, with resultant improvements and extension of its applications.4-7 The method and equipment to be described here are thought to represent still further improvement in the results obtainable, with increased validity in their application to field problems. Sand OF Principles of Operation The underlying theory of the operation of the model is given in references I, 2 and 3. However, a brief statement of principles involved is given herewith. The applicability of the model is based on the fact that Ohm's law and d'Arcy's law are exactly analogous; whence, electrical flow through a conducting medium may be used to simulate homogeneous fluid flow through a permeable medium. If two electrodes are placed in a conducting (ionized) solution and connected to the positive and negative terminals of a source of direct current, the positive ions of the solution will move toward the negative terminal, Since the velocity of an ion in an electrolytic medium is proportional to the electrical gradient, just as the velocity of a fluid particle in a porous medium is proportional to the pressure gradient, the motion of the ions in the potential field will be the same as the motion of fluid particles in a porous medium if the positive and negative terminals (input and output wells) and boundary conditions are made equivalent in shape and distribution. In order for the analogy to hold exactly, the sand must be assumed to have uniform porosity and permeability and the input

Jan 1, 1946

By Holbrook G. Botset

It is possible by means of the electrolytic model to simulate water-flooding or gas recycling systems involving input and output wells, and also the encroachment of a natural water drive. The results are obtained pic-torially, and by simple measurements and calculations the percentage of recovery is obtained qualitatively as a function of the total input. Introduction The increased demand for petroleum products, together with the decline in discovery rate and the higher cost of recovery as deeper formations are brought into production, has stimulated interest in methods for studying and predicting efficiencies of various production programs. Among methods Of recovery that have become of increased significance recently are gas recycling in condensate fields and secondary recovery by water-flooding. The electrolytic model is a useful device for studying such methods in the laboratory, at least in a qualitative way. The original experiments with electrolytic models and the development of their application to the study of secondary reCoverY problems were published in 1933. 1,2,3 Subsequently other investigators continued the development and modification of the bait method, with resultant improvements and extension of its applications.4-7 The method and equipment to be described here are thought to represent still further improvement in the results obtainable, with increased validity in their application to field problems. Sand OF Principles of Operation The underlying theory of the operation of the model is given in references I, 2 and 3. However, a brief statement of principles involved is given herewith. The applicability of the model is based on the fact that Ohm's law and d'Arcy's law are exactly analogous; whence, electrical flow through a conducting medium may be used to simulate homogeneous fluid flow through a permeable medium. If two electrodes are placed in a conducting (ionized) solution and connected to the positive and negative terminals of a source of direct current, the positive ions of the solution will move toward the negative terminal, Since the velocity of an ion in an electrolytic medium is proportional to the electrical gradient, just as the velocity of a fluid particle in a porous medium is proportional to the pressure gradient, the motion of the ions in the potential field will be the same as the motion of fluid particles in a porous medium if the positive and negative terminals (input and output wells) and boundary conditions are made equivalent in shape and distribution. In order for the analogy to hold exactly, the sand must be assumed to have uniform porosity and permeability and the input

Jan 1, 1946

By G. K. Manning, C. H. Lorig

TWO metallurgical tools have acquired wide use within the past several years as a means of studying the transformation characteristics of steel. One is a technique used first by Bain and Davenport for determining the transformation characteristics of a steel at constant temperature; the second is the end-quench hardenability test. Constant-temperature transformation curves like those of Bain and Davenport have done much to rationalize the metallography of steel; however, in commercial practices, constant-temperature transformation is seldom encountered, therefore only rarely can such curves be directly applied. The real reason for the determination of such curves lies in the fact that they provide a way of thinking about transformation that is both convenient and productive. The end-quench hardenability test is a more practical means of studying transformation, for, by correlating positions on the hardenability bar with shapes of different masses, an almost direct application of the results can be made. Unfortunately, the end-quench test, though practical, can do very little toward improving the metallurgists' way of thinking about transformation. These two metallurgical tools, dealing with precisely the same phenomenon, should be very closely associated in metallurgists' minds. Actually, they are frequently pushed into separate mental corners and considered as being more or less distinct and unrelated. The reason for this is that no strong connecting link between them has been developed. An attempt is sometimes made to relate these two tools by projecting the critical cooling rate on the isothermal transformation plot as illustrated in Fig. I. The critical cooling rate is considered as a constant rate-though in practical applications, cooling rates are never constant—and this constant cooling rate is given uniform significance from the Ae temperature down to the temperature of initial transformation. A little thought indicates the errors of such a procedure. Certainly the time interval spent just below point A of Fig. I cannot be as effective in promoting nucleation as is the time interval spent just above point B. Yet the procedure represented in Fig. I considers all the time spent between temperatures A and B to be just as effective in promoting nucleation as though all the time were spent at temperature B. Furthermore, change the shape of the isothermal curve between points B and C in any way desired, and the required critical cooling rate is not changed one iota. This cannot possibly be true. Such a way of thinking about critical cooling rates not only is incapable of giving any results that are quantitatively satisfactory but is likely to give very misleading qualitative results.

Jan 1, 1947

By G. K. Manning, C. H. Lorig

TWO metallurgical tools have acquired wide use within the past several years as a means of studying the transformation characteristics of steel. One is a technique used first by Bain and Davenport for determining the transformation characteristics of a steel at constant temperature; the second is the end-quench hardenability test. Constant-temperature transformation curves like those of Bain and Davenport have done much to rationalize the metallography of steel; however, in commercial practices, constant-temperature transformation is seldom encountered, therefore only rarely can such curves be directly applied. The real reason for the determination of such curves lies in the fact that they provide a way of thinking about transformation that is both convenient and productive. The end-quench hardenability test is a more practical means of studying transformation, for, by correlating positions on the hardenability bar with shapes of different masses, an almost direct application of the results can be made. Unfortunately, the end-quench test, though practical, can do very little toward improving the metallurgists' way of thinking about transformation. These two metallurgical tools, dealing with precisely the same phenomenon, should be very closely associated in metallurgists' minds. Actually, they are frequently pushed into separate mental corners and considered as being more or less distinct and unrelated. The reason for this is that no strong connecting link between them has been developed. An attempt is sometimes made to relate these two tools by projecting the critical cooling rate on the isothermal transformation plot as illustrated in Fig. I. The critical cooling rate is considered as a constant rate-though in practical applications, cooling rates are never constant—and this constant cooling rate is given uniform significance from the Ae temperature down to the temperature of initial transformation. A little thought indicates the errors of such a procedure. Certainly the time interval spent just below point A of Fig. I cannot be as effective in promoting nucleation as is the time interval spent just above point B. Yet the procedure represented in Fig. I considers all the time spent between temperatures A and B to be just as effective in promoting nucleation as though all the time were spent at temperature B. Furthermore, change the shape of the isothermal curve between points B and C in any way desired, and the required critical cooling rate is not changed one iota. This cannot possibly be true. Such a way of thinking about critical cooling rates not only is incapable of giving any results that are quantitatively satisfactory but is likely to give very misleading qualitative results.

Jan 1, 1947

ALABAMA Auburn.-Brown, R. L. Battelle.-Green, G. G. Bessemer.-Abbott, C. E. Dobbs, G. G. Ferguson, V. Birmingham.-Aldrich, T. H. Aldrich, T. H., Jr. Allen, A. W. Bonnyman, J. Bowron, J. Crawford, G. G. Crockard, F. H. Ellis, E. E. Fairbairn, C. T. Gambrill, G. T., Jr. Geismer, H. S. Hiller, E. McCormack, G. B. Maben, J. C.

Jan 1, 1917

By James Aston

A proper consideration of this subject is not confined to the technical channels of production and metallurgy. It concerns an industry, and should cover economic aspects which are of material importance in any program of development. The discussion may logically be treated under three subdivisions, as follows: (1) manufacture, (2) characteristics related to quality of material; (3) adaptability and exploitation of product. Manufacture of Wrought Iron The manufacture of wrought iron is the most ancient art of the ferrous metal industry. The eighty years or less of existence of processes identified with our modern "Age of Steel" is a relatively brief interval compared with the several thousand years associated with the production of wrought iron by man. From the primitive early methods of production, manufacture for many centuries followed the line of direct reduction. There were developments as experience was gained through the years; but man's needs for a strong, ductile, forgeable product were met by reducing the ore to metallic iron in a single-stage operation. Following the development several centuries ago of what has become our modern blast-furnace operation, manufacture of wrought iron was gradually transformed into a two-stage method of first producing cast iron and then refining this to the desired degree of forgeability; the forerunner in principle of today's scheme of manufacture of steel. The product retained the essential characteristics of highly refined base metal with iron-silicate slag incorporation, which were associated with the material resulting from direct reduction methods. Cort's invention of the puddling process in 1784 is a landmark in wrought-iron manufacture. It consisted essentially in adapting a coal-fired reverberatory furnace to the refining operation; thus lifting the industry out of the slough of

Jan 1, 1935

By S. R. Balajee, I. Iwasaki

The interaction between British gum 9084 and dode-cylammonium chloride (DAC) at quartz and hematite surfaces was established from coadsorption studies and streaming potential measurements. The cationic DAC interacts with the somewhat anionic British gum 9084, leading to the formation and adsorption of a binary complex of DAC-British Gum 9084 at the interface. The parallel ability to depress quartz along with hematite as a result of the interaction between DAC and British gum appears to be the main reason for the ineffective depressant action of starches and starch derivatives in the cationic flotation of iron ores. Amines are not particularly selective collectors for the flotation' of siliceous gangue from iron ores and, therefore, a suitable iron oxide depressant is needed for a satisfactory separation. Various starches and their derivatives have been extensively tested with oxidized iron ores,'-3 and it has been empirically established that British gums and dextrins are preferable. However, for the flotation upgrading of magnetite-taconite concentrates from 8 or 8.5% Si O2 to about 5% Si 02, British gums, which have been used so successfully on oxidized iron ores, have been found to have no effect and oftentimes are actually deleterious.4 In previous articles,5-7, starches were shown by adsorption measurements, flotation tests, and floccula-tion tests to interact with calcium ions in solution, and it was thought that a study on the interaction between starches and dodecylammonium ions would be able to shed some light on the anomalous flotation behavior described above. In fact, starches are known to interact markedly with paraffin-chain-type surface active agents and, thereby, to precipitate the starch or inhibit the iodine-starch reaction.8 From X-ray diffraction studies and viscosity measurements, the formation of a helical complex between mylose and a surface active agent has been postulated.9 The interaction with other types of hydrophilic colloids, such as synthetic polymers and proteins, has also been investigated and is usually explained in terms of van der Waals' force interaction and/or ion-ion interaction. In the present investigation, the interaction of British gum and dode cylammonium chloride on quartz and hematite was studied by adsorption and streaming potential measurements in an attempt to establish the mutual adsorption behavior of British gum and dode-cylammonium chloride on mineral surfaces and to clarify the anomalous depressant activity of British gum in the cationic flotation of iron ores. All the measurements were carried out at a natural pH of near 7 because dodecylammonium chloride gives maximum selectivity of flotation separation at this pH2 and to avoid any third parameter in the system. EXPERIMENTAL MATERIALS AND METHODS Minerals: The quartz and hematite samples used for the adsorption tests were prepared as described in a previous paper,"J except that the specific surfaces of the samples were increased to 5,860 and 16,000 Sq cm per gm, respectively. For the streaming potential measurements, the 48165-mesh fractions screened out of the original samples were etched with hydrochloric acid, washed repeatedly with water, and stored under water in Pyrex bottles. Reagents:DodecyIammonium chloride (DAC) was prepared1 1 by bubbling dry hydrogen chloride gas through a benzene solution of high-purity dodecylamine supplied by Armour and Co. British gum 9084, received from Corn Products Co., was solubilized by first dispersing it in water to produce a 0.05% solution and then homogenizing it in a blender for 5 min. Distilled water was used in the preparation of the samples and the solutions and for all test work. Adsorption Measurements: The procedure for the adsorption density determinations was also the same as that described in the previous paper.1° The residual concentrations of the British gum and the DAC in the supernatant solution were analyzed colorimetrically by the phenol-sulf uric-acid and amine-picrate methods, respectively. The validity of the mine-picrate method for the colorimetric analysis of DAC in the presence of British gum and the analysis of British gum in presence of DAC were checked by establishing calibration curves between optical density and concentration. Streaming Potential Measurements: The cell assembly for the streaming potential measurements was similar to that described by Fuerstenau.' The streaming potential

Jan 1, 1970

By F. E. Smith, David R. Mitchell, B. M. Bird

DENSE-MEDIA processes utilize the familiar laboratory float-and- sink procedure on a commercial scale. Just as wood chips float on water and sand sinks, ,so coal floats and refuse sinks when placed in a medium intermediate in specific gravity between the coal and refuse. Liquids intermediate in specific gravity between coal and refuse used in commercial plants are of four types: (1) Organic liquids of high specific gravity-halogenated hydrocarbons; (2) dissolved, salts in water; (3) pseudo liquids obtained by suspending solids, such as sand, in water, and (4) fluidizing a mass of sand or other solids by air currents. Those most widely used for cleaning coal are solutions of calcium chloride in water and a suspended-sand pseudo liquid. Laboratory float-and-sink testing is an intermittent operation during which every opportunity is given for particles lighter than the medium to float and particles heavier to sink. Commercial processes are continuous, vertical and horizontal currents of the separating medium occur as either part of the process or unavoidably produced by the introduction of feed and withdrawal of products, so that the exact separation of the laboratory technique is not duplicated by commercial processes. However, separations close to the theoretical are obtained in commercial machines by careful technical control of the process. Most machines in commercial installations are crowded to get as much out of the equipment as possible, so that careful technical control is necessary to get the recoveries and grade of product desired. Sizes usually cleaned are plus 3/16-in. or plus 1/8-in. in the United States and plus 1/16-in. in Great Britain: Coal as small as 1 mm. has been cleaned in some experimental installations. The separation of coal from refuse in sizes finer than about in. is made difficult by viscosity' effects and hence at the present time cleaning is confined to the coarser sizes. Technical advances in the art of cleaning coal by dense-media

Jan 1, 1943

By R. S. Dean

AMONG naturally occurring inorganic compounds, magnetite has many unusual and interesting properties, and it is the purpose of this paper to call attention to these properties and review possible uses of magnetite that might be based on them; in other words, to see what uses may be found for magnetite as a physical rather than as a chemical entity, as a mineral rather than as an iron ore. The Mineral Physics Studies initiated in the Metallurgical Division of the U. S. Bureau of Mines a few years ago gathered together much information on mineral properties, and they are therefore the principal source of material for this paper.

Jan 1, 1937

By E. I. Radzinovsky, D. W. Dareing

This paper presents theory which is used to predict rock-bit bearing life reduction due to simple harmonic variations in bit forces. The theory is based on the premise that if a constant load acts for a certain fraction of the life which the bearing would have if that constant load were applied for its entire life, then the same fraction of thelife of the bearing is consumed. Total bearing life is related to simple harmonic variations in bearing life associated with instantaneous bearing loads. The results show that rock bit bearing life is not affected appreciably by forces commonly impressed upon a bit, but it is affecied appreciably by relatively large dynamic bit forces occasionally encountered during drilling. In addition, the results show that the life of sealed bearings is more sensitive to bit force variations than is the life of unsealed bearings. INTRODUCTION Roller bearings are important components in roller cone rock bits because they transmit a large portion of the drill collar weight to the formation being drilled. Unfortunately, they have a relatively short life under down-hole drilling conditions. Roller bearings are usually the first bit components to fail, and their failure leads immediately to failure of the entire bit. Short roller bearing life, and thus short bit life, is due mainly to high unit loads transmitted by the bit and to the adverse environment in which the bearings operate. The results of the study discussed in this report show how dynamic bit forces also affect roller bearing life. The purpose of this paper is to discuss theory developed to predict the effect of different magnitudes of periodic bit forces on roller bearing life. Theoretical results are used to compare the life of rock bit roller bearings subjected to steady forces to the life of rock bit roller bearings subjected to unsteady forces similar to the type of unsteady forces measured at the bit with a special downhole recording instrument. BACKGROUND AIanufacturers of bearings have conducted laboratory tests which show how bearing life is affected by steady bearing load. 1 The well-known empirical equation which defines bearing life follows from bearing test data. It is: where L = bearing life, hr P = bearing load, Ib C = constant q = exponent (constant). The effect of environment on bearing performance is manifested through the exponent q and the constant, C. King,2 in similar tests conducted on roller bearings used in rock bits, showed that, in addition to the load, the environment (abrasive materials, chemical components, etc.) greatly affects bearing life. His data, which show how the life of roller bearings in a 7-7/8-in. W7R bit rotating at 60 rpm is affected by bit weight and fluid environment, are displayed on a log-log plot by broken lines made up of straight line segments. Each broken line corresponds to a given environment. One segment (q = 1.4) of the broken line corresponding to a fluid environment of barite mud is shown in Fig. 1 along

Jan 1, 1966

E. E. Olcott, New York City: Prof. Kemp's valuable description of the Lancaster Gap mine is in line with many other able contributions on the origin of mineral deposits that the Institute has lately brought forward. The splendid contribution that Prof.

Jan 1, 1895

By Charles Malcolmson

IN the United States, improvements in methods of combustion have made possible the use of the smaller sizes of anthracite. This coal is now being reclaimed from the culm banks accumulated by the miners in the more prodigal years. To-day the freshly mined "slush" is segre¬gated and stored against the time when, through briquetting or some other means, it may be utilized as a commercial fuel. For many years Europe has achieved enviable results in the conservation of her small coal by briquetting. This profitable industry, first placed on a commercial basis in France in 1842, has grown to such magnitude that the "'production during 1913 exceeded 36,000,000 short tons. Briquets produced in Great Britain are used principally for steam purposes and the greater part of the output is either exported or taken by the Admiralty. On the Continent the briquets are sold in all branches of the coal trade. The French railways consume from 16 to 40 per cent. of their fuel in briquet form, and in Germany the lignite briquets, (of which 20,000,000 tons were produced in 1913) are as familiar and interesting to the American traveler as the huge porcelain stoves in which they are burned. It is not strange, therefore, that aggressive and far-sighted promotors heralded this means of converting our ubiquitous coal waste into revenue. To the superficial student the briquetting process seemed so simple as to make success easy. It is for this reason principally that the path of the industry in America has been strewn with failures. The rash enthusiast had either not worked out the mechanical problems involved or had failed to grasp the local conditions under which the briquets must be made and sold. It may be confidently stated, however, that in spite of the many vicissitudes through which it has passed, coal briquetting is now an accomplished economic success in this country, and as a profitable adjunct to the coal industry it has come to stay.

Jan 2, 1915

By G. S. Cole, G. F. Bolling

Fluid flow strongly influences ingl structure and the columnar -to-equaaxed transition. Artificial flow patterns siwzilar to the nuturul ones act to induce this transition, while dampening forces act to suppress this transition. It is shown here how simple mechanical forces can be applied to a systerrz in order to induce or slipPvess relative fluid flow and the change both the structure transition and the exact structures obtained. The example used is the effect of slow rotations and oscillations 012 a cooling- ingot (of laboratory scale). The details of rotution and oscillation for various cooling rates, lenlperal~ire gradients, and sizes of ingot are related to other solidzfication variables. THE grain structure of a casting can be changed by altering the fluid motion during solidification. Just how important these changes are depends directly upon the degree to which the fluid motion can be controlled. An early step in understanding the nature and influences of fluid motion was taken by studying natural thermal convection; when a static mechanical device was used to suppress natural flow the result was opposite to that obtained when an electromagnetic device was used to augnlent flow in a pattern similar to the natural one. ''2 Suppression allowed more columnar growth to occur, but "augmented natural convection" brought about an earlier columnar-to-equiaxed transition (CET). Since the solidification of a free ingot must have characteristics somewhere between those displayed during suppression and augmentation, we know that natural convection must influence the CET. Further, since heat transfer in the liquid is always some time-dependent combination of convection and conduction, it can easily be guessed that the temperature gradient in the liquid is the vital factor affecting the CET.1,2 It is obvious that the structure arising from the unadulterated solidification of an ingot, without external influence, is rarely if ever the best possible one. Although the pattern of the natural fluid flow may be considered efficient, the magnitude of the flow and the heat transfer decrease freely from the outset. For a

Jan 1, 1968

By R. E. J. Putman

Introduction Self-tuning regulators are a class of controllers built around the concepts of sampled data theory, and are especially suitable for implementation in a digital microprocessor or minicomputer control system. The algorithms used are distinctly different from those based upon analog control techniques and include automatic adjustment features which permit them to adapt to unmeasured changes (in, for example, ore grindability) or process nonlinearities (as exhibited by cyclone classifiers). They are also designed to handle transport lags in a simple manner, for example, anticipating the effects of a variable recycle rate on particle size distribution. The advent of distributed control systems will encourage the exploration of these techniques in the minerals processing industries, and particularly for improving the control of comminution circuits, which are especially energy intensive. This paper outlines some current work in progress on this topic. Background Those engaged in the practice of process control have long had two philosophical problems for which solutions have been actively sought - what is optimal control and how can we attain it in some heuristic fashion automatically. The basic analog controller can be represented by the differential equation: [V = Ko + K1 f y • dt + K2 dt(1)] where: v and y are the instantaneous values of output and error respectively and K0, K1, and K2 are tuning constants. The empirical rules for establishing the values of K0, K1, and K2, which provide stability, have evolved from the initial suggestions of Ziegler and Nichols(9) in 1942 and have served their purpose well. However, later analyses demonstrated that there are in fact many combinations of the values of K0, K1, and K2 which, besides being stable, behave better or worse in relation to other process control criteria; some examples are duration of error, amplitude of a damped response, magnitude or rate of movement of control valve or adjustment of speed regulator, etc. The definition of optimality had broadened. In 1964, Kalman(4) published his classic paper which tried to resolve these problems. He defined a

Jan 1, 1982

By Walter R. Hibbard, Harold Margolin

The effect of ten ternary additions on the aging of a Cu-Ag alloy was measured by X ray, microstructure and hardness. A supersaturated copper-rich transition structure was found. The effect of the ternary element was related to differences between transition and precipitate lattice parameters and analogies with solution and strain hardening. IN addition to the prerequisite of diminishing solid solubility with falling temperature, the theory of coherency hardening1 proposes that the principal source of hardening during precipitation is strain caused by coherency between the matrix and precipitate. For a given system greater coherency hardening would result from lengthening the period of coherent growth and/or increasing the number of nuclei, other things remaining equal. However, the hardness change during aging is a function of a number of phenomena in addition to coherency hardening, such as dispersion hardening, loss of coherency, solute depletion, matrix recovery or recrystal-lization, coalescence, and their relative time sequences. The present investigation was undertaken to study the effect of ternary additions on the age-hardening of Cu-Ag alloy. For this purpose a series of alloys were made containing as ternary constituents Mg, Al, Si, P, Mn, Ni, Zn, As, In, and Sb. These elements were added to a master 5 wt pct Ag in Cu alloy in such amounts as to obtain alloys listed in Table II containing the following approximate atomic percentages: 96 pct Cu, 3 pct Ag, 1 pct ternary addition. A 97 atomic pct Cu, 3 atomic pct Ag alloy was used as a comparison standard. There have been numerous investigations of age-hardening in Cu-Ag alloys2-lo but few of ternary Cu-Ag alloys. Pfister and Weist" found that 1 wt pct Ni reduced the solubility of Ag in Cu above 600 °C and that the rate of precipitation was slower than in polycrystalline Cu-Ag alloys of similar silver content. More recently Hodge, Jaffee, Dunleavy, and Ogden12 investigated the effect of ternary additions of Mg, Li, P, Cd, Zn, Zr and Be on strength properties of Cu-Ag alloys. Mg, Cd, and P were found to increase strength in the aged and cold-worked condition. Experimental Procedure Charges weighing 7.5 lb were melted in a closed carbon crucible under a reducing atmosphere* of nitrogen and hydrogen. A Durville-type casting procedure with a hot-top arrangement was used to obtain a sound casting, 2x2x43/4 in. Prior to rolling and annealing of the ingots, a trial solution anneal of rolled sections of the hot-top portions indicated that at 780°C melting was avoided except for the Cu-Ag-Sb alloy. This alloy could not be produced as a single phase within the limits of temperature control. i 3" to 5oC, since melting occurred at 64O °C, and below this temperature precipitation was

Jan 1, 1952

record with the Royal Flying Corps was considered a remarkable one, for he was at the front within two months of the date on which he was granted a commission, during which interval he took the prescribed technical course at Oxford, and aviation training at Netheravon and Bristol. On Sept. 14, 1916, he took his first flight over the German lines, when his engine stalled and he had to volplane down, fortunately landing on the French side of the lines. On Sept. 16, he went over the lines with six others, and not returning immediately with the others, was lost. He tried to make for the sea and come back following the course of a river, but when he did descend he found that he was 60 miles west of Paris and 100 miles south of his lines. He flew over to Paris and stayed there for the night, going back to his squadron the next morning. Then on Oct. 4, he was sent up at night for the first time, and in making a landing he passed the flares just as he struck the ground, which put him in total darkness. He struck something and his machine turned a complete somersault, which accident put him in the hospital for ten days. In December, 1916, he left the 21st Squadron and was transferred to the 24th, as the 21st was made an Artillery Squadron and he preferred to remain a fighting scout. In the same month, he was made Acting Flight Commander for about 6 weeks, and about April 3, 1917, his rank of Flight Commander was confirmed. The beginning of May he started to introduce a number of new machines for his squadron, these being of an entirely new type. On May 19, he was up with one of the machines in the evening, practising sharp turns and dives, when the wings suddenly crumpled up and he fell 700 ft., being killed instantly. He was buried in a French Cemetry at Monchy Lagache about 8 miles southeast of Perronne, and about 25 miles east of Amiens. Sergeant Herbert Moore Harbach Herbert Moore Harbach was born in Lebanon, Pa., Apr. 4, 1891, graduated from the Lebanon High School in 1911, and entered State College from which he received his degree of Bachelor of Science in Metallurgical Engineering in 1915. He was employed by the Lackawanna Iron Co., at Buffalo, W. Y., and was later transferred to their Lebanon plant to start up the newly erected benzol plant. He was later made foreman of the coke ovens, which position he held after it was bought by the Bethlehem Steel Co., and until he enlisted in the service of his country in September, 1917. He was stationed at Camp Meade, Md., until the spring of 1918, when he was transferred to the C. W.

Jan 1, 1920