Search Documents

By L. S. Richardson, N. J. Grant

Iodide-grade titanium, two oxygen alloys, and two aluminum alloys were studied by means of creep-rupture tests from 1000° to 2000°F. From the test information an evaluation was made of, 1) the relative creep-rupture strengths of the u (hexagonal-close-packed) and 0 (body-centered-cubic) forms of titanium and some of its alloys; 2) the effects of solid-solution strengthening by oxygen and aluminum on the u and 0 structures; and 3) the extent and effect of atmospheric oxygen alloying on rupture life in tests above about 1000°F. THE use of titanium alloys at temperatures above 1000° F has been considered unlikely by most investigators because of low creep strength (based on a requirement for room-temperature ductility, formability, and weldability) and low oxidation resistance. The results of this testing program do not entirely uphold this pessimism in terms of strength and oxidation resistance. The observations described below are based entirely on stress-rupture results, although some creep tests were also carried out on these alloys. Three items of primary importance are covered: 1) Stress-rupture data in the form of the Larson-Miller parameter curves for several titanium alloys at temperatures up to 2000°F; 2) The relative strengths of the hexagonal-close-packed a structure and the body-centered-cubic 0 structure; 3) The effects of solid-solution alloying on the creep-rupture properties of titaniu'm at elevated temperatures. Only two investigatons have reported the creep- rupture properties of titanium at temperatures above 1000° F. Lunsford and rant' tested iodide titanium; their values are also utilized in the paper. EXPERIMENTAL PROCEDURE After a few tests had been made in a conventional creep-rupture test machine, it became clear that some sort of atmospheric protection would be necessary for short-time tests conducted at temperatures above 1600°F, or for times greater than 100 hr at 1200°F or above. Several furnace units and test machines were constructed, the most successful of which is shown in Fig. 1. Certain experimental difficulties peculiar to titanium were encountered; for example, the use of molybdenum holders was dictated because titanium forms low melting-point eutectics with conventional high-temperature alloys containing appreciable amounts of iron, nickel, or cobalt. This same difficulty made the use of chrome l-alumel thermocouples in direct contact with a test specimen impossible, above about 1500" F. The high-temperature high-vacuum furnace shown in Fig. 1 was capable of maintaining a vacuum of better than 10"5 mm of mercury at 2000°F (pressure measured in cold part of system) and 5 X lo-' mm at room temperature. Most of the tests eonducted in vacuum were at temperatures

Jan 1, 1960

By Canada Ernst & Whinney

INTRODUCTION The principal objective of this chapter is to provide guidance in understanding and making effective use of published financial statements of mining companies. Although financial statements only represent a gathering together of information relevant to an enterprise's financial position and results of operations, they increasingly reflect the complexities of the modern day business environment. In the mining industry, a wide variety of accounting practices have evolved to deal with the unique aspects of the business in the absence of authoritative accounting pronouncements from standard-setting bodies. Given such complexities and divergent practices, financial statements of mining companies are not easily understood and cannot be used effectively as a tool in decision-making without a basic knowledge of fundamental accounting concepts, generally accepted accounting principles and their application in the mining industry. As such, this chapter is not restricted to a discussion of the accounting for the unique aspects of the mining industry. These aspects are dealt with at length but the text also includes a discussion of general accounting concepts and practices which have wide application in the mining industry. Frequent references are made in the text to international practices and to specific rules and requirements of individual countries. In this respect, the scope is restricted to four major mining environments, Canada, the UK, the US and Australia, all of which have made significant contributions to the development of generally accepted accounting principles. Acknowledgements This chapter was prepared under the direction of Ian Murray of Ernst & Whinney in Toronto, Canada. Contributions were received from Graham Butt, Mark O'Sullivan and Dominic Robinson, all from Ernst & Whinney in Toronto and Bill Duvall and Tom Schoenbaechler from Ernst & Whinney in Louisville, Kentucky, US. The authors would also like to acknowledge the assistance received from David Ferguson, Don MacLean, David Taylor and Susan Zoutman from Ernst & Whinney, Toronto, from the UK and Australian practices of Ernst & Whinney and from Ernst & Whinney International. FINANCIAL STATEMENTS - ELEMENTS AND CONCEPTS Financial statements were originally a stewardship report to owners to satisfy them that management had given a proper account of the resources with which it had been entrusted. Today, the number of users of financial statements has expanded to include the following groups: - shareholders, present and prospective; - lenders, present and prospective; - financial analysts; - regulatory authorities; - taxing authorities; - labour unions and employees; and - creditors and customers. The expectations of these user groups differ. For example, investors and lenders require information that will indicate the adequacy of their security and the profitability of the enterprise; taxing authorities will be concerned with the concept of income; labour unions and employees will focus on the profitability of the enterprise. Ground Rules for Preparing Financial Statements Responsibility for Financial Statements Financial statements are the representations of management. This may strike the reader as a rather obvious statement. It is important to remember, however, the role of judgment in accounting. Notwithstanding the promulgation of accounting standards in the developed countries, considerable flexibility remains in the selection of accounting practices and methods and in their presentation. Arguably, there is more flexibility in the mining industry as few countries have developed standards to deal with its unique aspects. Accordingly, financial statements are as much a product of management's perspective and philosophy as they are a compliance document.

Jan 1, 1985

By R. J. Marcotte, C. T. Eddy, R. J. Smith

The objectives of the investigation herein reported were to determine: (I) the S-curves for certain selected cast steels, (2) whether or not the published S-curves for wrought steels are satisfactory for use on cast steels of similar composition, and (3) to prepare hardenability curves of the selected cast steels. In order to make the final comparisons between cast and wrought steel more completely tangible, it was deemed advisable not only to determine S-curves for the steels submitted in the cast condition but also to roll some of the cast-steel test bars and determine comparison S-curves on such wrought material. This procedure eliminates the composition variable and makes it possible to reveal the differences resulting from plastic deformation of the cast structure in addition to providing the comparison with published data on wrought steels. Cast Steels The cast steels selected for the preparation of S-curves, or time-temperature transformation curves, were similar to S.A.E. series 1030, 2330, 4130 and 4330. Of these the 1030 was supplied by The Crucible Steel Casting Co., Cleveland, Ohio, and the other three by The Sawbrook Steel Castings Co., Lockland, Ohio. The steels were furnished in the as-cast condition. The manufacturers supplied the chemical analyses and the properties that could be obtained in the heat-treated condition—all of which is summarized in Table I. The metallographic and dilatometric procedures and equipment were in general standard. The specific technique employed was described in a report of the Steel

Jan 1, 1945

TO metallurgists generally, Arthur S. Dwight is no stranger even to those who do not know him personally. He is one of those contributors to technical progress whose names will go down to posterity because of their being attached to a successful machine or process, such as Dorr, Hardinge, or Marcy, or Wedge, MacDougall, or Herreshoff. The roasting and sintering method and equipment developed by Colonel Dwight and his associate, the late Richard L. Lloyd, may be found in lead smelters throughout the world, and also in many metallurgical works dealing with other ores, including those of iron. It is ordinarily used to desulphurize and agglomerate fine ores for subsequent smelting. Colonel Dwight's citation as James Douglas Medalist reads: "For his contributions to the art of smelting nonferrous ores; and particularly for his pioneer work in developing equipment and technique for sintering such ores and metallurgical products." The medal was awarded at the last Annual Meeting of the A.I.M.E. but unfortunately the medalist was unable to leave Florida at the time to receive it in person.

Jan 1, 1942

By Earl Ingerson

BORE surfaces of used guns commonly show a pattern of cracks in various degrees of development. It has been suggested that these cracks may aid erosion by providing channelways for the gases, eventually leading to the tearing out of blocks of metal. Under the general studies of gun erosion conducted at the Geophysical Laboratory it appeared desirable to consider this factor, and to determine the resistance to surface cracking offered by gun steel and by various other materials that might be used in the bores of guns. METHOD AND APPARATUS In order to make such a determination it is necessary to have (I) an arrangement in which the surface to be studied can be subjected to conditions similar to those in a gun with respect to temperature, pressure (developed by explosion gases), composition of the gases and length of time the surface is exposed to the gases; and (2) a specimen that can be examined readily after any number of shots, and then fired again, if necessary. The first of these conditions can be met by using an explosion vessel designed by H. S. Roberts of the Geophysical Laboratory. Fig I shows a cross section of the apparatus. The "gun" G from which the charge is fired is made from the receiver of a caliber 0.30 army rifle, M1903, and the charges are prepared in caliber 0.30 cartridge cases. The test specimen S is held in place by a cone-shaped plug P and by a steel ,bridge B which is bolted to the outside of the explosion vessel on either side of the section shown. The plug, in turn, is held in place by a screw collar C. Maximum pressure is controlled by a brass rupture disk R. Part of the explosion gases flow past the two flat areas on S. st the two flat areas on S. Temperature and composition of gases, and the time before the rupture disk breaks, can be controlled by amount and kind of powder used, and pressure can be controlled by using rupture disks of different thickness. While the explosion vessel used was not designed so that temperature and pressure could be measured, in other vessels of closely similar size and shape containing proportionate charges of the same kind of powder as that used for standard testing procedure, values of 2700°K and 5000 psi were obtained. Since the orifices past the flat areas on the plug are small compared to the rupture disk hole (1:16), most of the gas goes out through the rupture disk when it breaks. The amount that goes by the plug depends on (I) the pressure attained before the rupture disk breaks and (2) the time it takes for this pressure to be built UP. The second condition (examination at will after any firing) is met by using for specimens short rods that have flat areas ground on opposite sides. These flat

Jan 1, 1947

By J. G. Bartram

Jan 1, 1934

By Arthur Fleischer

THE Kalunite process? for the production of metal-grade alumina from alumina-containing ores is applicable, considered from a general point of view, to any aluminous raw material that can be converted to potassium alum or equivalent normal alum. This result of modern technology has been the subject of a continuous study and development since 1929, on a laboratory and test-plant scale, with initial emphasis on the utilization of alunite as the raw material. The research and developmental program was carried out by the Kalunite Company and its successor, Kalunite, Inc., an affiliate of the Olin Corporation of East Alton, Illinois. The process is now approaching the time for a major test in its history with the completion of construction of a plant having a capacity of zoo tons of alumina per day in Salt Lake City for the conversion of Marysvale, Utah, alunite ores to alumina and potassium sulphate. The Salt Lake Alumina Plant is a Defense Plant Corporation project. PRODUCTION OF ALUMINUM The known existence of alunite deposits, especially in the Marysvale district, furnished the motive for the original inquiry into the utilization of this raw material for aluminum production. The deposits in this region were actively explored during World War I and utilized for the production of potassium sulphate, an essential fertilizer, of which a shortage of monumental proportions then existed. Up to the twentieth century for alunite is a mineral with an ancient history-it was used in Europe and in China as a source of potassium alum. It never had been used successfully in. this country as a source of oxide for reduction to metal. Although the known reserves of this ore, which undoubtedly will be greatly expanded with a commercial outlet for this ore, are recognized to be sufficient for only a part of the present-day needs of aluminum, it has a definite place in the aluminum industry. Academically it points the way for future raw materials. The aluminum industry has undergone a remarkable growth in the past few years as a result of defense and war requirements. Its expansion in many ways has been beyond belief and prediction, both in volume and location. This wartime status of the industry has accelerated the consumption of bauxite to such an extent, that a re-evaluation of the raw material reserves for the future peacetime industry and for eventual wartime reserves is seemingly of concern. The generally accepted picture of bauxite ore reserves in the United States, especially in raw material suitable for treatment by the Bayer process, focuses attention on other possible sources of raw material of metal-grade oxide. The perspective for the development of a suitable process may have changed in the interim

Jan 1, 1944

By B. E. Field

COBALT is a silvery white metal with a slight bluish cast, strongly resembling nickel in its appearance and properties, notably its resistance to corrosion, although its alloys with other metals differ quite decidedly in their properties from those of nickel. The name cobalt was derived from the German "Kobold" meaning goblin and this came to be applied to the cobalt minerals which, although they resembled ores, did not readily yield metal when smelted by the primitive processes available in the Middle Ages. Cobalt minerals were used as pigments by potters and glass workers before the Christian era. Cobalt blue glass was found in the tombs of the Egyptians and in the ruins of Troy, and many colors used by the ancient Greeks and Romans contained cobalt. The ancients were entirely unaware that the colors they used were caused by cobalt and the metal itself was only isolated about the middle of the eighteenth century by Brandt although the preparation of cobalt compounds had been carried on in a small way ever since the opening of the silver-cobalt deposits at Schneeberg, Germany, in 1470. The metal is fairly hard, with a density when pure of 8.81 in the cast state and 8.92 after working. The com¬mercial grade of cobalt has a density of about 8.75 in the cast state. The atomic weight is 58.97. The Brinell hardness of the pure metal is 124; that of the commercial grade varies from as low as 100 to as high as 138, depending upon the impurities present. Pure cobalt has a sharp melting point at 1478°C. The tensile strength of the pure metal in the cast condition is said to be higher than that of any other pure metal. Kalmus gives it as 34,400 lb. per sq. in. for cast unannealed metal; the effect of annealing at 850 to 900°C. is to raise the strength slightly. The yield point is close to the ultimate strength and the reduction in area and elongation are both low. Mechanical working raises the tensile strength of pure cobalt rapidly and in the form of wire it will be over 100,000 lb. per sq. in. The presence of small quantities of carbon in the commercial metal raises the tensile strength to as high as 61,000 lb. per sq. in., the reduction in area and elongation being raised at the same time to approximately 20 per cent.

Jan 1, 1933

By W. R. Wilcox

The camphor-anthracene system was chosen as a transparent low-melting analog of the zirconium carbide -graphite system. Camphor and zirconium car -bide both grow nonfaceted, while casting of mixtures yields platelets of both anthracene and graphite. Zone melting of thin layers of organic was observed under the microscope. Irregular lamellar structures were produced at high values of the ratio of the temperature gradient G to the zoning rate V. The anthracene invariably led the camphor, indicating lower kinetic undercooling for the anthracene. The lamellar spacing was an order of magnitude greater than typical spacings for metal eutectic systems. Exact behavior depended on orientation of the anthracene. Oriented dendritic structures were produced at low values of G/V. Transient and oscillatory behavior were also observed—much of it unexpected. A.RC-CAST refractory carbide-graphite mixtures are promising thermal-shock resistant materials. Oriented structures of these materials would be superior to arc-cast materials for many applications. Mollard and Flemings1 and Cline2 have shown that aligned structures can be obtained for a wide range of Pb-Sn alloys. However, these metals both solidify in a nonfaceted manner while graphite yields platelets or flakes. In addition only small diameter samples of Pb-Sn alloys were produced because it was necessary to avoid free convection and to have high temperature gradients. The purpose of the present work was twofold: 1) To observe the solidification of a transparent low-melting analog of carbide-graphite systems and 2) to see if larger diameter samples can be produced. EXPERIMENTAL PROCEDURE When zirconium carbide-graphite mixtures are cast, the resulting structure naturally depends on composition. Carbide-rich mixtures yield metal-like nonfaceted carbide dendrites in a eutectic matrix. Graphite-rich alloys have graphite platelets in a eutectic matrix. Empirically it was found that camphor-anthracene mixtures produce similar structures with camphor being nonfaceted and anthracene forming plates. The organic eutectic melted at 116°C and was composed of 78 wt pet camphor.3 The camphor used was U.S.P. grade from Fisher Scientific Company; the anthracene was 98+ pet fro Aldrich Chemical Co. The impurity content is judged to be on the order of 1 pet. Mixtures ranging from 50 to 88 wt pet camphor were employed for the experiments. All but one of the experiments were performed on the microscope-stage zone melting apparatus described in detail elsewhere.4 The organic mixtures were contained in horizontal cells made of microscope slides or cover glasses. In most of the cells the organic was present as a very thin layer, thus giving almost two-dimensional growth behavior. The cells were moved slowly under a heated wire, which caused a molten zone to move through the solid at rates ranging from 0.01 to 5.4 cm per hr. The temperature gradient was estimated before moving the zone by measuring the distance between the line where all solid was melted (freezing point) and that where solid first began to melt (eutectic temperature). The temperature gradient was found to be 465°C per cm in the thinnest cells used, which were made by pressing together two microscope cover slips in the organic melt and then rapidly withdrawing them. RESULTS The experimental results are described in four parts: simultaneous growth, dendritic growth, irregular growth, and transients and erratic phenomena. Steady state data are summarized in Fig. 1. Except where noted all comments are for the cells containing a thin layer of organic. A) Simultaneous Growth. Simultaneous and roughly parallel growth of anthracene and camphor was obtained over the full range of compositions investi-

Jan 1, 1970

By Waynw P. Myers

Electricity, as normally thought of by a layman's definition, is a man- made force that has no color, no odor, is not visible, cannot be heard, yet man can control it and make it perform his work for him. A person dare not cheat on it, for it then will master him. It has laws, rules, and regulations that must be strictly adhered to if it is to perform in the safest, most reliable, and economical manner. In the early days of coal mining the power source was man himself. Later man employed steam and compressed air to reduce his muscle power requirements needed in the extraction of coal. By the turn of the 20th century, electricity had become the most common source of power for the coal industry. Steam and compressed air are still found in use in isolated cases today for specific applications; however, they are rapidly being replaced by electricity. Electrical laws and regulations are quite extensive and somewhat complex for the proper generation and use of electricity. Man-made laws, rules, and regulations for the care and handling of electricity, designed for man's safety, are rigidly enforced by Mine Safety and Health Ad- ministration (MSHA), as well as the various state departments of mines. BACKGROUND Until recent years most underground coal mines used direct current exclusively for all movable and for some stationary equipment. Exceptions were for permanent pumps, tipple, fan, and outside buildings where alternating current was normally employed. However, over 60 years ago there were mines with dual systems. Alternating current was used for cutting machines, drills, and pumps ; direct current for locomotives. There were no other machines as these were hand-loading mines. Later, during early mechanization in the 1920s, alternating current was also applied to loading machines at some mines. Use of dual electric systems then declined until fairly recently when

Jan 1, 1981

By W. C. Clarke

An empirical study of the nature of the embrittle-ment which occurs in martensitic and semiaustenitic precipitation hardening stainless steels upon exposure at temperatures of from about 550" to 875°F has been undertaken. This work was aimed at determining cazusation and means of controlling this phenomenon. A commercial copper bearing precipitation hardening alloy was used as a basic material for study. The effect of heat treatment variables was studied as was the effect of variations in analysis. It is concluded from the evidence that martensitic and semiaustenitic precipitation hardening stainless steels are subject to 885°F ernbrittlement similar to that observed in the straight chromium stainless steels. A characteristic of precipitation hardening stainless steels which has limited their use in certain applications is that they embrittle when held at temperatures in the range of from about 550" to 900°F. This is true to a more or less degree in all currently available alloys, either the basically martensitic type or the semiaustenitic type. The rate of embrittlement varies markedly with exposure temperature, being low at 550" to 600°F and in-creasing as the temperature increases. In spite of this embrittlement, these alloys with their unique combination of high mechanical strength, reasonable toughness, and good corrosion resistance are used in many hundreds of applications. Nevertheless, there are potential applications where the embrittle-ment described is a limiting factor. The purpose of this investigation was to study the embrittlement of these alloys and to find a way to control or eliminate it. GUIDELINES USED IN PRESENT WORK The work reported in this paper is based on a study of 17-4 PH*, a very widely used alloy. It has been used *Trademark of Armco Steel Corp., licensor. in pressurized water and boiling water atomic reactors operating at about 550°F for a number of years. As the life of such equipment is extended or operating temperatures are raised, the possibility of embrit-tlement becomes of increasing concern to materials engineers. Much investigation work was done with respect to the use of 17-4 PH at 550°F. K. C. Antony' states "Such estimation" (of an activation energy for the diffusion of chromium in iron) "would indicate W. C. CLARKE, Jr. is Senior Research Engineer, Advanced Materials Division, Armco Steel Corp., Baltimore. Md. This manuscript is based on a talk presented at the symposium on New Developments in Stainless Steel, sponsored by the IMD Corrosion Resistant Metals Committee, Detroit, Mich., October 14-15, 1968. significant secondary aging is improbable at temperatures less than 700°F within normal component service life". This statement is modified however by the recognition of the accelerating tendencies of applied stress and internal stress as well as the possible effect of irradiation. In this investigation of 17-4 PH, the H 1100 (1900°F-1 hr oil quench or air cool + 1100°F-4 hr-air cool) condition was used, partly because this condition is normally used in atomic reactors. As shown later, the precipitation hardening temperature has no real bearing on the rate of embrittlement. An exposure temperature of 800°F was selected since embrittlement at 800°F is rapid, permitting development of relative data in time periods of 400 to 500 hr. For those not familiar, a nominal present day analysis of 17-4 PH is: C Mn P S SiCrNiCuCbN 0.04 0.30 0.015 0.015 0.60 16.00 4.30 3.25 0.23 0.030 TYPICAL BEHAVIOR OF 17-4 PH Figs. 1 and 2 show the behavior of a commercial heat of 17-4 PH under the conditions defined. Characteristically, 800°F exposure causes a rapid drop in Charpy V-notch impact strength. Tensile and yield strengths gradually increase and a gradual loss of elongation and reduction of area occur, accompanied by an increase in hardness. Notched tensile strength increases to 125 hr exposure and then sharply decreases after exposure for 500 hr. The notched vs un-notched tensile ratio remains virtually constant to exposure for 125 hr (1.67 to 1.56) but drops to 1.15 after 500 hr. Tensile ductility is not alarmingly affected even after much longer exposure times than these. For example, samples aged at 1100°F for 1 hr exposed at 800°F for 4000 hr showed a drop in elonga-tion of from 13 to 11 pct and in reduction of area of from 58 to 37 pct. Notched impact is the property SmIgth KSI 3JJ[/__________^UTS-Nrteh 260 ;/- 240 —^ 200 UTS-Smooth________._, o ioo mo Sob" m Too Hours Exposure Fig. 1—Effect of exposure at 800°F for various times on notched tensile strength and smooth tensile and 0.2 pct yield strength of 17-4 PH in the H 1100 condition.

Jan 1, 1970

By Clyde E. Williams, V. N. Krivobok, C. H. Herty

THE extreme effect of the depression on the steel industry is well illustrated by the fact that the amount of iron ore shipped from the Lake Superior district was the lowest in 47 years. Something over 3 1/2 million tons of ore was shipped in 1932, compared with over 65 million tons in 1929. It is not surprising then that practically no advancement in iron ore beneficiation has been made. Improved research and development work, however, was continued at the Michigan College of Mines in the survey of the lean iron ores of Michigan with reference to the possibility of their concentration; at the University of Minnesota in its large-scale jigging studies of Lake :Superior ores; and at Battelle Memorial Institute in the development of improved jigging of iron ores. The successful operation of the new Hadsel mill at a gold property in California gave such low grinding costs on a quartz ore as to give much encouragement in the iron ore industry for a cheapening of the cost of grinding lean ores for concentration.

Jan 1, 1933

By Alexander Anderson

TABLES showing the drift and inclination of wells surveyed in the years 1924 to 28' and in the year 1929' have already been published. Each of these tables included a little over 1,000,000 ft. of rotary hole. In the year 1930 the table -shown-in . Fig. 1, comprising, the results of surveys .of 1,030,344 ft. of hole and representing 11,642 individual survey readings, was compiled. For that purpose we selected 'I only wells that had been drilled in California during that year. The footage of Fig. 1 differs from the two earlier tables in that the wells were all drilled in the year 1930. In the earlier tables, the footage shown was surveyed in the years designated, but some of the wells were drilled in earlier years.

Jan 1, 1931

By W. F. Holbrook, C. E. Wood, E. P. Barrett

THE high-frequency laboratory induction furnace with a rotating liquid crucible enables research workers to conduct certain investigations heretofore very difficult or impossible to realize because vessels are not obtainable that are capable of resisting the physical conditions or the chemical actions to which they are subjected. Applications for patents covering commercial uses of centrifugal liquid crucibles were filed in the United States in 1919,1 in France in 1925, in the United States and Germany in 1926,2 and in France in 1927.3 In 1928, Schuette and Maier,4 of the Bureau of Mines, reported the construction of a whirling table beneath a high-frequency induction furnace. SHAPE AND SIZE OF CENTRIFUGAL LIQUID CRUCIBLES When a vessel containing a liquid is rotated, the inner surface of the liquid takes the shape of a paraboloid under the simultaneous action of centrifugal force and gravity. The internal dimensions of the paraboloid rotating liquid crucible are governed by the diameter of the container and .its speed of rotation. Melted Wood's metal was poured into cylinders 2 1/2 in. in diameter, which were rotated at 180, 300, and 468 r.p.m. When the metal was solid, a slurry of plaster of Paris was added, and rotation continued until the plaster had set. Fig. 1, a photograph of sections of the cylinders, shows the effect of speed of rotation of the containers upon the shape of the inner surface of the rotating liquid crucibles. TYPES OF FURNACES Three types of high-frequency induction laboratory furnaces using liquid-metal crucibles were designed and constructed by the Blast

Jan 1, 1938

Jan 1, 1952

By P. Wynblatt, J. E. Dorn

The effect of strain rate, temperature, and interstitial impurity concentration on the flow stress was investigated in a poly crystalline Fe-2 pct Mn alloy. The temperature dependence of the flow stress was found to be independent of the interstitial impurity concentration, removal of interstitials merely decreasing the atherma1 stress level. Below 160%, the large temperature dependence of the flow stress was interpreted in terms of the Dorn-Rajnak theory of the Peierls mechanism of plastic deformation. Above 160"K, some other thermally activated intrinsic meckanisln seems to be operating. The strong temperature dependence of the flow stress of bcc iron at low temperatures has been studied by numerous investigators and interpreted in terms of several different thermally activated dislocation mechanisms. The following mechanisms have been proposed: a) interaction of dislocations with interstitial impurity atoms1 or with solute atoms in general; b) interaction of dislocations with clusters of impurity atoms;3 c) resistance to the motion of dislocations due to jogs on screw dislocations;* d) resistance to the motion of dislocations due to the Snoeck effect;' and e) interaction of dislocations with the intrinsic resistance of the bcc lattice or Peierls "hills". In previous work: it was found that the plastic behavior of polycrystalline iron containing 2 wt pct Mn (and 100 ppm C + N) is in good agreement with predictions based on the Peierls mechanismlo from 77" to 160°K whereas from 160" to about 370°K another as yet unidentified thermally activated mechanism is operative. The purpose of the present investigation was to determine the effect of interstitial impurities on the temperature dependence of the flow stress, by purifying the previously investigated alloy with respect to interstitial impurities. The investigation revealed that removal of the interstitial impurities to a level that eliminated Cottrell locking and the Portevin-LeChatelier effect (i.e., serrations in the stress-strain curve due to dynamic strain aging) affects neither the strong temperature dependence of the flow stress at low temperatures nor the general characteristics of the higher-temperature behavior. Such purification, however, lowered the athermal yield stress. I) EXPERIMENTAL PROCEDURE AND RESULTS The material used in this investigation consisted of an Fe-2 wt pct Mn alloy having the following additional elements present: 0.004 pct C, 0.006 pct N, 0.05 pct 0, 0.004 pct S, 0.003 pct P, and 0.001 pct Si. This was the same material as that studied in the previous investigation and will henceforth be referred to as the "impure material". The as received -jr by 2 in. hot-rolled bars were cold-rolled to 0.08-in. thickness, recrys-tallized under argon for 30 min at 80O0C, and further cold-rolled to 0.053-in. thickness. Flat tensile specimens 3 in. wide having a 1.625-in.-long gage section were machined from the sheet and then purified. The first stage of purification consisted of holding the specimens at 850°C for 24 hr in a stream of hydrogen saturated with water vapor at room temperature. Material prepared in this fashion will subsequently be referred to as "wet hydrogen purified material". It has been estimated that this type of treatment reduces the carbon content of iron to less than 5 ppm.' The second stage of purification consisted of holding the specimens in a closed system through which hydrogen was circulated past the heated specimens as well as a zirconium hydride getter. The specimens were held at 850°C and the getter at 800°C. The process was continued for 212 hr. The starting material for this process was wet hydrogen purified material. Material prepared in this manner will be referred to as "ZrHz purified material". The technique used was substantially the same as that described by Stein et al.' who have shown that the carbon level at the end of the process is reduced to about 5 parts per billion. The mean grain size of the three materials was found to be -60 C( for the impure material and -160p for the wet hydrogen and ZrHz purified materials. All tensile testing was carried out on an Instron Testing Machine either in controlled-temperature baths or at fixed-point baths such as boiling liquid nitrogen, and so forth. When fixed points were used the temperature was kept constant to better than *1°C whereas in all other tests the temperature variation was less than *2°C. Test of Purity. It was not possible to determine the purity achieved at each stage of the purification because the resulting level of interstitial impurities was near or below the limit of sensitivity of standard analytical techniques. It was possible, however, to obtain a qualitative measure of the extent of purification from the appearance of the stress-strain curves for the three materials. Fig. 1 shows the stress-strain curves for the three different materials tested at 300°K. It can be seen that the effect of wet hydrogen

Jan 1, 1967

By M. A. Cook

Sutherland used an ion-pair adsorption model to derive the author's hy-drolytic pee-acid) adsorption equation for the contact bubble curves of Wark and Cox. To do so it was necessary to postulate that the sum of coverages of surface anion sites by the collector and depressant anions is practically unity. It is here shown that the free energy of Sutherland's postulated collector ion (x-)-depressant ion (OH-) exchange reaction (for no other than the OH- to compete with X-), namely EX + (OH-) Z SOH- + X-, is in some cases positive and X- should not even adsorb. Also, in many cases the (OH-) adsorption must be quite negligible even though the collector covers only about a sixth of the mineral surface at the threshold of air bubble contact. This, however, contradicts the postulate that permits one to derive the correct bubble contact eqwztion for the ion-pair model. Furthermore, the requirement for charge neutrality leads in the ion-pair model to the (impossible) constancy of the ratio @+)/(OH-) along a contact bubble curve in which pH may change by more than seven units. HYDROLYTIC ADSORPTION EQUATION Hydrolytic (free-acid or free-base) and ion-pair (H', X-, or R', OH-) adsorption models of the collector in metal sulfide and similar flotation systems are superficially alike and somewhat difficult to differentiate. This is because they yield, under seemingly valid assumptions, equivalent forms of the equations describing the distribution of the collector between the aqueous solution and the mineral surface. This has been discussed by the author and associates1-4 and more recently by Sutherland,' both for simple collector-mineral and for more complicated collector-depressant-mineral systems. In the hydrolytic adsorption model the equations describing the contact bubble curves of Wark and coxeJ7 are as follows :2 Here X is the collector anion, D- the depressant anion, 9, and On are the fractions of the free-acid sites S on the surface of the mineral covered by collector and depressant free acids, respectively, and @ is the fraction of uncovered sites. Kx is the free-acid collector dissociation equilibrium con- stant, K1 that for the free-acid collector adsorption, KD that for the free-acid depressant dissociation, and K2 the equilibrium constant for the free-acid depressant adsorption. Eqs. 1 to 5 yield upon simultaneous solution the result is the critical free-acid concentration for bubble contact in the absence of depressant-free acid. Eq. 8 expresses the conditions along a simple collector-mineral contact bubble curve for the case HD = 0, or V = 0. Last and Cook showed that Eq. 6 applies generally and with good accuracy in the collector-depressant-metal sulfide mineral systems. Inci-dentally, it has been shown by infrared absorption studies that in some cases the free-acid adsorption process splits out water.' In this case, Eq. 2 might be written SHOH + HX Z SHX + H20, with a similar equation replacing Eq. 4 for depressant-free acid-water exchange. This possibility does not change, however, the basic equations or considerations of the hydrolytic adsorption model. Indeed, this type of free acid-water exchange reaction was predicted for fluorite and iron ore flotation by oleic acid in the dry grinding and boiling processes.410

Jan 1, 1961

By P. A. Beck

ACCORDING to the traditional definition,1 re-x crystallization is a process taking place upon annealing of cold worked metals, characterized by the appearance of new strain-free grains, growing at the expense of the cold worked grains until ultimately the new crystals completely replace the cold worked structure. In metals like brass this process was observed long ago to take place simultaneously with the return of the mechanical properties to those characteristic of well annealed material. The above definition implicitly assumes that the matrix in which the new grains are growing is essentially still in the cold worked condition at the time it is absorbed by the new grains, i.e., that the energy stored in the metal during cold working is not greatly decreased by recovery, prior to recrystallization. Accordingly, the bulk of this energy is assumed to serve as the driving force for the process of recrystallization. Recently, a great deal of evidence accumulated, indicating that the traditional concept may be considerably in error. Suzuki' found that by far the largest portion of the stored energy of cold work in compressed polycrystalline copper is released in the early stages of annealing, well in advance of recrystallization. Thus, the new recrystallized grains are undoubtedly growing in a matrix which is, at least energetically, no longer in the cold worked condition, but has nearly returned to the annealed state. It is true that in Suzuki's experiments the major hardness changes due to annealing were observed to take place concurrently with the formation and growth of the new grains, but this process apparently involved the release of only a minor residual fraction of the stored energy of cold work. Confirming in this respect the views of Wood," several recent investigations by various techniques lead to the conclusion that the grains of many, if not all, metals in the cold worked condition consist of small, slightly disoriented "crystallites" or "sub-grains".* (After appreciable deformation at room temperature, the subgrain size in copper appears to be about 7.104 cm and in high purity aluminum about 2.10-4 cm.) Recent investigations which demonstrated this phenomenon most convincingly are those of Heidenreich8 with hammered high purity aluminum, of P. B. Hirsch and collaborators7,8 with cold worked polycrystalline aluminum, copper, nickel, iron, gold, etc., and of Warren and Averbach9 with a rolled copper plus 2 pct Si single crystal. In addition to the existence of slightly disoriented sub-grains, the cumulative evidence from these investigations also shows that in the cold worked condition the subgrains themselves are severely strained. With regard to the early stages of annealing, Heiden-reich's results indicate that within the subarains of hammered high purity aluminum the strain gradually disappears, without discernible migration of the subboundaries. This recovery process presumably accounts for the major portion of the energy release

Jan 1, 1953

By Howard Eavenson

EARLY in 1917, the United States Coal & Coke Co. secured options on several tracts in Harlan County, Ky., aggregating about 1.9,000 acres in area, and after careful prospecting by outcrop openings and diamond drilling, completed the purchase late in July of that year. This property is situated in the eastern end of Harlan County, south of the Poor Fork f Cumberland River, and extending across Big Black Mountain to the Clover Fork of Cumberland River, a distance of about 7 mi. (11.3 kg.). It extends from the Kentucky-Virginia line westward for about 6 mi. Looney Creek, which empties into Poor Fork, crosses the property for about 4 mi. (6.4 kg.), and as several of the seams within the property outcrop along this stream, it afforded an easy, and the logical, place for development. The property is on the northern side of the geological trough formed by the uplifting of Stone Mountain, on the southern, and Pine Mountain, on the northern side; the northern boundary along Poor Fork is practically at the base of Pine Mountain. This, area has been described in various geological reports.1 The main seam on this property is the one known variously as the "C," Benham, Keokee, Taggart, and Roda; it is, also called, by the Kentucky Geological Survey, the Kellioka seam of the western portion of Harlan County. This seam averages, in this property, about 5 ft. (1.5 m.) in thickness, although local rolls reduce this thickness considerably over small areas; and at the extreme western end of the property the seam splits. It is usually clean, although occasionally a small parting occurs within a few inches f the bottom f the seam; it is one f the best

Jan 9, 1921

By J. C. Griffiths, D. W. Bennion

A mathematical model, which does not assume a priori that stratification exists, but was designed to test for the stratification was developed. The model segmented the reservoir horizontally into areas of common variance, then divided it vertically into strata (if strata were present). Next, trend surface techniques were used to determine the lateral extent and variation of each stratum. The model was tested on two reservoirs (sandstone and limestone) using porosity as the reservoir rock property. The sandstone reservoir contained approximately 60,000 samples from 2,000 cored wells, while the limestone reservoir had approximately 24,000 samples from 430 cored wells. Within the areas of common variance tested, the model was able to distinguish four separate lithological units or zones in the sandstone reservoir, four in the Marly section and seven in the Vuggy section of the limestone reservoir. INTRODUCTION To accurately predict the movement and production of fluids from a reservoir rock, it is necessary that the reservoir engineer have a knowledge of the rock properties and their distribution throughout the reservoir. For this study, a reservoir rock is defined as a solid containing interconnecting holes or voids which occur relatively frequently and are dispersed within the rock in a regular or random manner. The fraction of bulk volume that these interconnecting voids occupy is called porosity. The rock must also possess sufficient permeability to allow fluids to move through it and it may be composed of one or more strata or lithological units. A stratum or lithological unit as defined in this study is a body or volume of reservoir rock whose properties are so distributed that its lateral and vertical extent can be traced throughout or through a portion of the reservoir. Operationally, the existence of strata are question- able unless the variance within strata is less than among strata. Within the past few years computers have been widely used as a tool for calculating movement and production of fluids from reservoirs. Most prediction models require some type of a mathematical description of certain reservoir rock properties. In the past, most of these models have been relatively simple. Some have assumed vertical variation but no lateral variation, while others have assumed lateral variation but no vertical variation. In general, most of these models have not used functional relationships to predict reservoir rock properties as functions of position. The object of this study was to develop a model which would predict lateral and vertical variations of reservoir rock properties. Since samples are usually available from only a small portion of the total reservoir rock, it seemed logical that if measurements from these samples were to be used to infer the properties of the actual reservoir, the data should be treated statistically as a sample from the total population (reservoir). Therefore, the model developed in this study to predict reservoir rock properties was a stochastic model. The model was tested using porosity (a macroscopic reservoir rock property) measurements from two reservoirs — the first, a sandstone reservoir from which 60,000 samples were obtained; and the second, a limestone reservoir with 24,000 samples. Several investigators have proposed methods to determine the vertical and areal variation of a reservoir rock property. Stiles: Dykstra and Parsons 2 and Suder and Calhoun3 have all developed waterflooding prediction techniques which assume vertical variation but no lateral variation. Stiles developed a method to segment a reservoir arbitrarily using frequency distribution. Law4 suggested that porosity has a normal frequency distribution and that permeability has a log-normal frequency distribution. Elkins and Skov 5 proposed that when a reservoir is segmented vertically, the

Jan 1, 1967