Search Documents

By C. C. Wright, T. S. Spicer, R. G. Bowman

In recent years considerable publicity has been given to the problem of atmospheric pollution by fuel-burning equipment. Legislation has been stimulated and smoke ordinances have been enacted, the provisions of which show a definite trend toward stricter control of the emissions not only from the stacks of industrial fuel users but also from the chimneys of domestic consumers. As a result of war conditions, some slackening in the enforcement of these ordinances may be noted, but this is only a temporary expediency caused by the changes necessary in the distribution of the nation's fuel supplies and difficulties in securing the necessary equipment. Previous trends may be expected to continue in the postwar period. Largely because of the consumer demand for automatic heat, but partly because of the legislation against smoke emission, there has been a marked increase in the use of domestic underfeed stokers with the past decade. When correctly adjusted and operated, these units reduce the smoke emission materially, so that even the high-volatile bituminous coals may be burned with little or no emission of objectionable smoke. Unfortunately, however, the use of the domestic underfeed stoker introduces another problem; namely, fly-ash. Production of Fly-ash The term "fly-ash" is a misnomer, since the fly material is generally a mixture of small carbonaceous particles varying from green coal to coke, and inorganic particles ranging from fluffy ash to small particles of fused clinker. For want of a more comprehensive name, however, the term fly-ash is used throughout this paper to include all the fly material. Even with hand-fired furnaces a certain amount of fly-ash is produced, which necessitates periodic cleaning of the boiler flues or furnace radiator, the smoke pipe, and occasionally the chimney itself. With stoker operations the amount of fly-ash is increased many fold, because of the higher velocity of air travel through the fuel bed. Frequently the amount of this fly-ash attains such proportions as to constitute a definite nuisance to the householder and his neighbors and distracts very materially from the otherwise automatic or semi-automatic performance of the stoker. Virtually all the boilers and hot-air

Jan 1, 1944

By T. S. Spicer, C. C. Wright, R. G. Bowman

In recent years considerable publicity has been given to the problem of atmospheric pollution by fuel-burning equipment. Legislation has been stimulated and smoke ordinances have been enacted, the provisions of which show a definite trend toward stricter control of the emissions not only from the stacks of industrial fuel users but also from the chimneys of domestic consumers. As a result of war conditions, some slackening in the enforcement of these ordinances may be noted, but this is only a temporary expediency caused by the changes necessary in the distribution of the nation's fuel supplies and difficulties in securing the necessary equipment. Previous trends may be expected to continue in the postwar period. Largely because of the consumer demand for automatic heat, but partly because of the legislation against smoke emission, there has been a marked increase in the use of domestic underfeed stokers with the past decade. When correctly adjusted and operated, these units reduce the smoke emission materially, so that even the high-volatile bituminous coals may be burned with little or no emission of objectionable smoke. Unfortunately, however, the use of the domestic underfeed stoker introduces another problem; namely, fly-ash. Production of Fly-ash The term "fly-ash" is a misnomer, since the fly material is generally a mixture of small carbonaceous particles varying from green coal to coke, and inorganic particles ranging from fluffy ash to small particles of fused clinker. For want of a more comprehensive name, however, the term fly-ash is used throughout this paper to include all the fly material. Even with hand-fired furnaces a certain amount of fly-ash is produced, which necessitates periodic cleaning of the boiler flues or furnace radiator, the smoke pipe, and occasionally the chimney itself. With stoker operations the amount of fly-ash is increased many fold, because of the higher velocity of air travel through the fuel bed. Frequently the amount of this fly-ash attains such proportions as to constitute a definite nuisance to the householder and his neighbors and distracts very materially from the otherwise automatic or semi-automatic performance of the stoker. Virtually all the boilers and hot-air

Jan 1, 1944

By O. W. Rees, Gilbert H. Cady

Unit coal calorific values represent a close approach to pure coal values; they possess characteristics theoretically inherent in the latter values. They are essentially uniform in the same seam for areas possessing essentially uniform geological environment. They are higher in older than in younger coals in most cases, and in deeper than in shallower coals. In general, they display characteristics closely in accordance with expectation assuming that they are essentially indices of rank. Because it possesses these characteristics, the unit coal value is essentially a standard value, characteristic of each bed in each local region. Hence it can be used as a basis for determining the accuracy of results in newly established laboratories, or when new equipment is installed, or in checking the results of different laboratories, or even in determining the character of coal as mined or prepared if ash, moisture and sulfur values are known. DISCUSSION (A. C. Callen presiding) R. P. Hunson,§ Wayland, Ky. (written discussion).—One of the interesting observatioris made by the authors is that there is a more or less definite correlation between unit coal calorific values and the geological environment of the coal bed. It is very interesting to note that, in general, the unit B.t.u. value increases with the increase in the probable original depth of burial, and that each seam tends to increase in calorific value toward the areas of diastrophic instability. It is generally conceded that Parr's formula, for determining unit coal values, is about as accurate as any formula subsequently proposed for the same purpose. In his formula, Professor Parr did not differentiate between the sulfur present as iron pyrites and that present as organic sulfur. However, the practical application of the formula has shown that this is of little consequence. I agree with the authors that unit coal calorific values are useful ill determining the accuracy of calorimetric determinations, and in determining the character of the

Jan 1, 1934

By James Quigley

As the outcrop mines in the West developed into underground operations, systems of ground sup- port were gradually evolved. In the early coal mines there was little need for support except near the dirt line in portals, where stone masonry was common. Where the top was shaley or broken, native pine props with light cross bars and legs furnished enough support even in Utah's 25-ft coal seams. As depth of workings increased, roofs and backs of the same general nature as those near the surface became more and more unstable and required more and more support. Some coal airways show this tendency very clearly. From the surface down the same type of roof shows deterioration which an experienced eye can translate into a measure of depth under surface rather than change in rock characteristics. Rock bolts, developed by various companies and by the U. S. Bureau of Mines, have become an effective substitute for timber in sections of some metal and nonmetal mines formerly requiring excessive timber support, and further use of war surplus landing mats, chain link fencing, and a new punched channel developed by one of the steel companies has enabled other mines to operate deposits where costs of timber and lack of clearance for timber support would have prohibited mining. The block caving mines have made extensive use of reinforced concrete underground to achieve similar ends under difficult conditions. Steel sets are standard in many Bureau of Reclamation projects, although these are usually covered in with concrete to make the permanent structures the Bureau's reclamation projects require. But the use of steel in mining operations is limited and has been confined principally to the iron ore mines of Michigan, Wisconsin, and Minnesota. Some mines have installed used rail as posts, caps, and crossbars, but a rail section is not suited for load carrying, and used rails are generally brittle, having a tendency to fail without warning when overloaded.

Jan 7, 1959

By Paul R. La Pointe

GEOTECHNICAL OBJECTIVES OF UCG PROGRAM Underground coal gasification (UCG) is one of several in situ extraction technologies for utilizing deep, otherwise unmineable coal. This technology involves the injection of air or oxygen into the target coal seam, ignition of the coal and recovery of product gases. Geotechnical characteristics of the coal and enclosing rock strata strongly influence the success of this Process. The flame front follows the coal cleats (Hill, 1979), and cleating and bedding control the manner in which coal collapses into the cavity, thereby affecting recovery efficiency (Ramirez and others, 1982). Moreover, coal seams typically behave as fracture dominated aquifers in which cleat orientations govern subsequent contaminant dispersal. For these reasons, the Anaconda Minerals Co. undertook a detailed study of fracturing within the Wyodak-Anderson Coal in the eastern Powder River Basin (PRB) near its Rocky Hill UCG test site (Fig. 1). STRESS HISTORY AND FRACTURING IN THE POWDER RIVER BASIN Vertical jointing, or cleating, in coals may arise from shrinkage shortly after deposition under low confining pressures, or later in time, soon after burial but after the coalification process is well advanced (Ting, 1977). There is much evidence to support the formation of cleating after coalification (e.g. Hawkes and Mellor, 1970; McCulloch and others, 1974), which suggests that the stress state existing at that time strongly influences cleat formation. McCulloch and others (1974) argue that the typically better developed face cleat forms parallel to the plane containing [ol] and [o2]. Where the relation between cleats and stess has been studied (McCulloch and others, 1974; Stone and Snoeberger, 1977; Ward, 1977; Kulander and Dean, 1978), the highly systematic face cleat strongly parallels the [o1] direction. Stone and Snoeberger (1977) report face and butt cleat measurements of N70E and N29W for the Felix Coals 220 m stratigraphically above the Wyodak at the Hoe Creek UCG site (Fig. 1). Structural trends also indicate the past state of stress in the PRB. Glaze and Keller (1963) suggest that the NE-SW regional compression during the late Permian formed major N-S fold lines and basement magnetic anomalies. Mapel (1959) describes folds having N60W and N30W rends in the northern PRB, as well as a large normal fault trending northeast. Glass (1976) also describes normal faults trending northeast. Similarly, Olive (1957) mapped normal faults

Jan 1, 1984

By E. van Walsum

Tunneling methods through rock have, since the successful development of explosives, relied almost solely on blasting. Over the last ten years, rock-tunneling machines (moles) have been developed and some major projects have been carried out successfully with the use of such machines, which rely on the destruction of rock by mechanical means rather than blasting. Various other basically new methods are presently under study, such as the use of laser beams, water jets, etc. For practical purposes, there are presently only two methods commercially available: 1) blasting or 2) tunneling by mole. A contractor would choose at present either one method or the other. Both methods have their advantages and disadvantages (Fig. 1). The thought has occurred that the next practical development in rock- tunneling technology might be a combination of the best features of the mole technique and those of the blasting technique. A preliminary evaluation of this approach indicated that there is definitely a good potential for fruitful developments along these lines. My purpose is to place on record some of the thinking and some of the ideas which were developed along these lines and to point out certain areas where development efforts are required. In trying to find an improved tunneling technique, we looked in particular for the following qualities: 1) safety, 2) continuity, 3) uniformity, 4) automation, and 5) flexibility. TUNNELING BY BLASTING Conventional tunneling by means of blasting proceeds generally in recurring sequences of events: 1) drilling, 2) loading, 3) firing, 4) mucking-out, and supplementary operations (such as scaling and lining). These four operations (drilling, loading, firing, mucking) proceed one after another.

Jan 1, 1970

By Joseph E Pogue

Over a period of years the writer has presented a number of studies1 on various aspects of proration, in a progressive attempt to analyze critically and constructively the economic complexities of this interesting institution, which in a decade has revolutionized the economics of oil production in the United States. In the course of the investigations leading to these papers, the changing nature of proration and the principles underlying its evolution have gradually become clear, so that it is now possible to depart from the analytical method and to construct a synthesis of the steps that, if furthered by the industry, should carry proration past the economic hazards that still surround it to the goal of maximizing the value of the petroleum resource to the industry and the public alike. Nature of Proration Proration literally means the allocation of demand among competing producers on a pro rata basis, but the term now carries a much broader significance for it is employed to describe the entire process by which the production of crude oil in the United States is regulated. There is naturally much confusion of thought on the subject, for proration is an evolving system of control based upon principles of conservation and equity and embracing a body of practices that are tending to adjust themselves to the needs of the situation but are subjected to varying and divergent influences in the process. As it is now constituted, proration is a planned production measure designed to prevent waste, insure ratable takings, and balance supply and demand. The procedure is administered by State regulatory bodies through use of the police power of the States under authority of State conservation laws; the practice is supported by a considerable degree of voluntary conformance on the part of operators; and the Federal Government has accorded its cooperation by providing advisory quotas, circumscribing imports, checking movements of hot

Jan 1, 1939

By Joseph E. Pogue

Over a period of years the writer has presented a number of studies1 on various aspects of proration, in a progressive attempt to analyze critically and constructively the economic complexities of this interesting institution, which in a decade has revolutionized the economics of oil production in the United States. In the course of the investigations leading to these papers, the changing nature of proration and the principles underlying its evolution have gradually become clear, so that it is now possible to depart from the analytical method and to construct a synthesis of the steps that, if furthered by the industry, should carry proration past the economic hazards that still surround it to the goal of maximizing the value of the petroleum resource to the industry and the public alike. Nature of Proration Proration literally means the allocation of demand among competing producers on a pro rata basis, but the term now carries a much broader significance for it is employed to describe the entire process by which the production of crude oil in the United States is regulated. There is naturally much confusion of thought on the subject, for proration is an evolving system of control based upon principles of conservation and equity and embracing a body of practices that are tending to adjust themselves to the needs of the situation but are subjected to varying and divergent influences in the process. As it is now constituted, proration is a planned production measure designed to prevent waste, insure ratable takings, and balance supply and demand. The procedure is administered by State regulatory bodies through use of the police power of the States under authority of State conservation laws; the practice is supported by a considerable degree of voluntary conformance on the part of operators; and the Federal Government has accorded its cooperation by providing advisory quotas, circumscribing imports, checking movements of hot

Jan 1, 1939

By S. H. Williston

IT is not often that bore hole surveys can be checked by actual civil engineering methods. A recent Arizona survey was checked by normal surveying methods and the comparison of the results should be of value to both oil and mining men. During the summer of 1948 the Phelps-Dodge Corporation, at its Copper Queen property near Bisbee, Ariz., drilled a 1245 ft, 8 in. diam, churn drill- hole in a mineralized area and cased part of it, intending to use it to transfer mill tailings for stope fill. The hole, as frequently occurs, was not straight, and, in endeavoring to locate the bottom in- the underground workings, they found no evidence of the hole at the underground coordinates directly below the surface location. The noise of the drilling tools was reasonably clear, but the direction of sound was uncertain. Preliminary tests with available equipment were not successful in locating the bottom of the hole. Be- cause of the mineralized character of the area and the fact there was some casing in the hole, any magnetic method of well surveying would give results ' of doubtful value.

Jan 1, 1950

By Gene D. Clayton, Robert R. Dimock

A time-consuming and expensive preshearing program to minimize the adverse effects of blasting on slope stability at Kennecott Copper Corp.'s Ruth Pit in east-central Nevada has been eliminated in favor of down-the-hole, nonelectric delayed blasting which can produce a smooth wall effect and improve blast fragmentation. The new blasting approach resulted from a Kennecott engineering investigation aimed at improving the stability of the extremely variable rock conditions found throughout the pit by reducing the vibrational energy imparted to the walls with conventional bench blasts.

Jan 4, 1977

By H. Rush Spedden, Arvid Thunaes

R. R. Knobler and F. E. Albertson—Following the testwork done by Thunaes and Spedden, a Sullivan deck plant was built for the Colquiri mill. This plant started to operate in April 1945 and continues in successful operation. Since May 1950 the Colquiri mill has operated with a completely revamped flowsheet at a rate of 1000 tons per day. The old Sullivan deck section was retained with this new flowsheet. The "slime plant" in Colquiri consists of one 12-cell Denver No. 18-Sp. Sub-A flotation machine, one 16-ft and one 12-ft hydroseparator, six five-deck Sullivan-frames and six shaking tables for cleaning up the Sullivan deck concentrates, as well as 12 Deister plus three Plat-O tables on which the fine sands, which are not treated on the S-decks, are concentrated. Only —325-mesh fines are treated on the Sullivan decks. The combined hydroseparator overflows are fed to the S-decks. From 1946 to 1949, i.e. with the "old" flowsheet and an average mill feed of 800 tons per day an average of 45 tons per day was treated on four Sullivan rougher frames. The two additional frames were used as cleaners. At times, up to 90 and 120 tons of slimes were treated successfully on this Sullivan deck installation. The average operating data for the S-deck section in Colquiri for the year 1949 were as follows: The tests reported in this paper indicated a tin recovery of 42 pct. The actual plant results for 1949 show a 54 pct tin recovery from the Sullivan decks. The total average quantity of tin produced from the S-deck section in 1949 was 15 tons of tin per month. This corresponds to 3 pct of the total mill recovery. The difference between the 6 pct overall recovery-increase expected after the tests in 1943 and the actual plant results given for 1949 is explained as follows. According to the tests, a total of 170 tons was expected to be routed to the Sullivan decks, but because of certain changes in the flowsheet and mill amplifications,

Jan 1, 1951

By H. Rush Spedden, Arvid Thunaes

R. R. Knobler and F. E. Albertson—Following the testwork done by Thunaes and Spedden, a Sullivan deck plant was built for the Colquiri mill. This plant started to operate in April 1945 and continues in successful operation. Since May 1950 the Colquiri mill has operated with a completely revamped flowsheet at a rate of 1000 tons per day. The old Sullivan deck section was retained with this new flowsheet. The "slime plant" in Colquiri consists of one 12-cell Denver No. 18-Sp. Sub-A flotation machine, one 16-ft and one 12-ft hydroseparator, six five-deck Sullivan-frames and six shaking tables for cleaning up the Sullivan deck concentrates, as well as 12 Deister plus three Plat-O tables on which the fine sands, which are not treated on the S-decks, are concentrated. Only —325-mesh fines are treated on the Sullivan decks. The combined hydroseparator overflows are fed to the S-decks. From 1946 to 1949, i.e. with the "old" flowsheet and an average mill feed of 800 tons per day an average of 45 tons per day was treated on four Sullivan rougher frames. The two additional frames were used as cleaners. At times, up to 90 and 120 tons of slimes were treated successfully on this Sullivan deck installation. The average operating data for the S-deck section in Colquiri for the year 1949 were as follows: The tests reported in this paper indicated a tin recovery of 42 pct. The actual plant results for 1949 show a 54 pct tin recovery from the Sullivan decks. The total average quantity of tin produced from the S-deck section in 1949 was 15 tons of tin per month. This corresponds to 3 pct of the total mill recovery. The difference between the 6 pct overall recovery-increase expected after the tests in 1943 and the actual plant results given for 1949 is explained as follows. According to the tests, a total of 170 tons was expected to be routed to the Sullivan decks, but because of certain changes in the flowsheet and mill amplifications,

Jan 1, 1951

By Sheldon Rideout, E. L. Kamen, B. S. Lement, Paul A. Beck, W. D. Manly

The 1200°C isothermal sections of the following ternary phase diagrams were investigated: Cr-Co-Nil Cr-Co-Fe, Cr-Co-Mot and Cr-Ni-Mo. In all these systems the u phase was found to form extended solid solutions. Two new ternary phases of unknown structure were identified. The existence range of intermediate phases of transition elements was correlated with 3d electron vacancy concentrations. THE occurrence of extensive ternary d solid solutions in the Cr-Co-Ni and in the Cr-Co-Fe systems was described in a brief note.' More recently d- solid solutions were also found in the Cr-Fe-Mo system by two independent groups of investigators.2,3 The existence of binary d phases in the V-Co and V-Ni systems, predicted in ref. 1, was experimentally discovered recently by Duwez and Baen and independently by W. B. Pearson, J. W. Christian, and W. Hume-Rothery.5 Duwez and Baen stated two general conditions for the occurrence of the d phase in alloys of the transition elements: "(1) The atomic diameters of the two metals do not differ by more than 8 per cent. (2) One of the two metals has a body-centered cubic structure while the other is face-centered cubic, at least in one of its allotropic forms." In the course of an extensive research program conducted at this Laboratory under the sponsorship of the NACA, several ternary systems, containing d solid solutions and also certain new ternary phases, were investigated. The present report describes the investigated portions of the 1200°C isothermal sections of the following ternary phase diagrams: Cr- Co-Ni, Cr-Co-Fe, Cr-Co-Mo, and Cr-Ni-Mo. It was found that the range of existence of the d phase in these four ternary systems, as well as in one of two ternary systems which were investigated by others, can be fairly consistently described in terms of electron vacancy concentrations. This supports the suggestion of Sully and Heal" that the d phase is an electron compound. Experimental Procedure The ternary alloys were prepared by vacuum induction melting in zirconia and alumina crucibles. Lot analyses of the metals used are given in Table I. Specimens of all alloys were annealed at 1200°C in an atmosphere of purified 92 pct helium and 8 pct hydrogen mixture. Alloys consisting mainly of

Jan 1, 1952

By Chas. H. Behre

MINING geology, both theoretical and practical, continued to make noteworthy progress during 1938. Mining companies generally, stimulated especially by the improvement in economic conditions during the latter part of the year, extended their workings and developed new ore bodies. Federal and state surveys expanded their search for favorable localities and actual ore bodies, with corresponding enlargement of regional knowledge. Theoretical investigations covered geochemistry of ore deposition, structural control of mineralization, and mineralogy of the ores (chiefly aided by the microscope). More geochemical work is greatly needed: ore searching is still too purely empirical, based on features that have been recognized else- where. Thus, clearer understanding of the conditions essential to transportation of metal salts is needed. Jean Verhogen has suggested that solubilities

Jan 1, 1939

By R. I. Jaffee, J. G. Dunleavy, H. R. Ogden, Webster Hodge

INTRODUCTION EARLY in 1946, at the instigation of the U. S. Army Signal Corps, the authors made an extensive survey of the available literature covering high-strength, high-conductivity alloys. For the purposes of the Signal Corps, the minimum tensile strength to be considered was 150,000 psi, together with at least 50 pct IACS conductivity. No single alloy was found to be in production, or mentioned in the literature, which had this combination of properties. The constitution diagram for the iron-copper alloys is not well established in the respect to the two-liquid region. Fig I, taken from the 1939 Ed. of the ASM Metals Handbook, shows a two-liquid system existing above the liquidus temperature, but disconnected from it. Although Ruer and Fick1 and Ruer and Goerens2 definitely established the fact that two liquid layers could occur in the system, Ruer3 was not convinced that the line off immiscibility was closed in the center. Maddocks and Claussen4 found no liquid immiscibility at temperatures up to 1570°C in alloys containing almost no carbon. Although the diagram would indicate age hardening of the copper-iron alloys is possible, Hanson and Fords found that little hardening effect could be obtained. However, Gordon and Cohen6 reported that the response is better if the quenching is very efficient. Although iron has a potent effect on the conductivity of copper, Hanson and Ford5 have shown that, when hot-rolled copper iron alloys are aged at 1200°F, the electrical conductivity decreases sharply with iron contents up to 0.2 pct Fe, and then levels off at conductivities between 60 to 70 pct IACS with compositions to 2.1 pct Fe. They also found that aging did not increase the tensile strength, although increasing iron content gave a moderate improvement in strength. High-strength copper-iron alloys, usually containing about 60 pct iron, had been reported by Smith and Palmer.7 They found that an alloy containing 56.4 pct copper, 0.21 pct magnesium, balance iron, would give a maximum tensile strength of 170,000 psi and an electrical conductivity of slightly over 35 pct IACS. The alloy could also be processed to have 150,000 psi tensile strength, and about 41 pct IACS conductivity. Decreasing the iron content increased the electrical conductivity, but the long mushy range during freezing of the alloy containing 10 to 20 pct iron made the production of good castings difficult, In spite of the difficulty encountered by Smith and Palmer with alloys of around 20 pct iron, it was decided to make a rather complete investigation 0f this type of alloy. As a result 0f this investigation, a method of alloying and fabricating copper alloys containing 10 to 15 pct iron was developed

Jan 1, 1948

By K. Mukai, M. Ishihara

This report is a brief discussion of the impurity levels both in primary aluminum and super-purily alnminim in connection with raw materials and proc-essing methods. Particularly, truce amounls of im-purities were analyzed by introducing nittss-speclro-gruphy and nenlron-aclivalian analysis techniques. Vanadium and gallium content in primary aluminum metal corresponded to theor amounls in anode coke. but the nickel content in primary aluminum was hide-pendent oj its amount in the anode cake. Sulfur in the anode colic might result in an increase of the iron content in the molten metal in the reduction cell. The content of sodium and calcium increased with increasing bath ratio. In the holding furnacc sodium content decreased rapidly, and nonmetallic inclusions merit separated front the mollen metal. Three-layer elctrolysis was effectire in eliminating many impuri-ties with the exception of copper, aluminum oxide. aluminum nitride, and some rare-earth elements. THE amount of impurities and nonmetallic inclusions in aluminum metal depends on impurities in the raw materials and various production processes. This paper presents an investigation of the behavior of impurities and nonmetallic inclusions in aluminum during the electrolysis process, the period in the holding furnace, and the process of three-layer electrolysis. Chemical analysis and emission spectrometric analysis have generally been used as methods to determine small amounts of impurities in both primary aluminum and super-purity aluminum; however. mass spectrography and neutron-activation analysis have been recently introduced into this field, and trace amounts of impurities can accurately be determined by these latter methods. EXPERIMENTAL WORK Common impurities were determined by means of absorptiometric. polarographic, flame-photometric. and emission-spectrometric methods. However, in the determination of trace amounts of impurities and non-metallic inclusions, the following methods were applied. In the analyses of trace impurities by mass-spec- trographic analysis, samples were exposed in the vacuum spark of double-focus ing Mattauch-Herzog type mass spectrograph (Japan Electron Optics Laboratory, Ltd.). Ilford Q2 photographic plates were used as ion detectors. Fe was used as the internal standard, and the atomic concentration of each element was calculated by the following expression and converted into the weight concentration: where E, and Ei are the exposures (coulomb) when isotopes of the internal standard and impurity elements (on which the estimate is based) show the same density, X is the percent (atomic) concentration of the standard, IF and Ii are the percent abundances of the isotopes of the standard the impurity elements (on which the estimate is based), and Ms and hfi are the mass of the isotopes of the standard and impurity elements (on which the estimate is based). The coefficient of variation in this method is about 40 pct in the range of 0.1 to 1 ppm. In neutron-activation analysis, irradiations were done in the nuclear reactors TRIGA-I1 (neutron flux: 4.7 x 10 11 n per sq cm per sec; Rikkyo University) or JRR-2 (neutron flux: 2 x 1013 n per sq cm per sec: Japan Atomic Energy Research Institute). After the chemical separation, a NaI (3 by 3 in.) scintillator connected to a 256-channel y-ray spectrometer (R.C.L.) was used for counting and recording various activated impurities. The coefficient of variation in this method is about 20 pct. In the analyses of nonmetallic inclusions, aluminum-oxide determination was carried out according to Fischer's method, 3 as follows. A slice of sample was cut off and the surface was cleaned. It was dissolved in bromine-methanol. The solution was filtered and the residue was washed. The residue was fused with potassium bisulfate flux. Then it was dissolved in weak acid, and oxine solution was added. The aluminum oxinate was extracted with benzene. Finally, aluminum was determined absorptio-metrically. Aluminum nitride determination was carried out as follows. A slice of sample was cut off and the surface was cleaned. It was put in the distillation apparatus and decomposed with sodium hydroxide solution. The solution was distilled. Then ammonia was absorbed and

Jan 1, 1967

By N. P. Peterson

The Castle Dome copper deposit is of the porphyry type and occurs in a body of quartz monzonite intruded into the pre-Cambrian formations and possibly into the lower part of Paleozoic limestones. The hypogene sulphide minerals include pyrite, chalcopyrite, and a little molybdenite, sphalerite, and galena. Pyrite and chalcopyrite are disseminated or occur in small closely spaced veins. The hypogene mineralization shows distinct zoning in the distribution of pyrite and chalcopyrite, so that the mineralized area can be subdivided into pyritc and chalcopyrite zones. Supergene enrichment, though not extensive, played an important part in the formation of the ore body, the chalcopyritc zone being the pro-tore. Several thin, gently dipping, diabase sills occur in the mineralized area, and the copper content of the rock in and near these sills is substantially higher than average. The formation of the ore body was caused by the combined effects of three forces: I. Zoning of the hypogene mineralization, 2. Richer copper metallization associated with the diabase sills, and 3. Supergene enrichment. Introduction The Castle Dome copper deposit is about 5 miles west of Miami, Arizona, and about 3 miles west of the Miami-Inspiration ore body. The Castle Dome open-pit mine is on the south flank of Porphyry Mountain, a prominent landmark of the region. In 1941 the deposit was being explored by the Miami Copper Co., but the exploration program was cut short when the decision was made to develop the property as a war project. The Castle Dome Copper Co., Inc., was organized as a wholly owned subsidiary of the Miami Copper Co., and arrangements were made with Defense Plant Corp. for developing and equipping the mine and for construction of a concentrating plant. Construction and development work was begun in January 1942, and milling operations started June so, 1943. Since that date, the mine has been in continuous operation by the Castle Dome Copper Co, under a lease agreement with Defense Plant Corp. producing copper at an average rate of 4,000,000 lb per month. To January I, 1946 the total production amounted to 121,088,000 lb of copper,4,271 oz of gold, and 211,755 oz of silver. A detailed study of the copper deposit and the surrounding area was undertaken by the U. S. Geological Survey in June 1943. Other members of the Survey participating in the work were C. M. Gilbert, G. L. Quick, and J. P. Albers. The results of this work will be published as a comprehensive report by the Geological Survey. General Geology The Globe quadrangle, which includes the Castle Dome area, was studied by F. L. Ransome1 of the Geological Survey in 1901 and 1902. His maps and descriptions were

Jan 1, 1949

By N. P. Peterson

The Castle Dome copper deposit is of the porphyry type and occurs in a body of quartz monzonite intruded into the pre-Cambrian formations and possibly into the lower part of Paleozoic limestones. The hypogene sulphide minerals include pyrite, chalcopyrite, and a little molybdenite, sphalerite, and galena. Pyrite and chalcopyrite are disseminated or occur in small closely spaced veins. The hypogene mineralization shows distinct zoning in the distribution of pyrite and chalcopyrite, so that the mineralized area can be subdivided into pyritc and chalcopyrite zones. Supergene enrichment, though not extensive, played an important part in the formation of the ore body, the chalcopyritc zone being the pro-tore. Several thin, gently dipping, diabase sills occur in the mineralized area, and the copper content of the rock in and near these sills is substantially higher than average. The formation of the ore body was caused by the combined effects of three forces: I. Zoning of the hypogene mineralization, 2. Richer copper metallization associated with the diabase sills, and 3. Supergene enrichment. Introduction The Castle Dome copper deposit is about 5 miles west of Miami, Arizona, and about 3 miles west of the Miami-Inspiration ore body. The Castle Dome open-pit mine is on the south flank of Porphyry Mountain, a prominent landmark of the region. In 1941 the deposit was being explored by the Miami Copper Co., but the exploration program was cut short when the decision was made to develop the property as a war project. The Castle Dome Copper Co., Inc., was organized as a wholly owned subsidiary of the Miami Copper Co., and arrangements were made with Defense Plant Corp. for developing and equipping the mine and for construction of a concentrating plant. Construction and development work was begun in January 1942, and milling operations started June so, 1943. Since that date, the mine has been in continuous operation by the Castle Dome Copper Co, under a lease agreement with Defense Plant Corp. producing copper at an average rate of 4,000,000 lb per month. To January I, 1946 the total production amounted to 121,088,000 lb of copper,4,271 oz of gold, and 211,755 oz of silver. A detailed study of the copper deposit and the surrounding area was undertaken by the U. S. Geological Survey in June 1943. Other members of the Survey participating in the work were C. M. Gilbert, G. L. Quick, and J. P. Albers. The results of this work will be published as a comprehensive report by the Geological Survey. General Geology The Globe quadrangle, which includes the Castle Dome area, was studied by F. L. Ransome1 of the Geological Survey in 1901 and 1902. His maps and descriptions were

Jan 1, 1949

By R. I. Jaffee, J. G. Dunleavy, W. Hodge, H. R. Ogden

Early in 1946, at the instigation of the U. S. Army Signal Corps, the authors made an extensive survey of the available literature covering high-strength, high-conductivity alloys. For the purposes of the Signal Corps, the minimum tensile strength to be considered was 150,000 psi, together with at least 50 pct IACS conductivity. No single alloy was found to be in production, or mentioned in the literature, which had this combination of properties. The constitution diagram for the iron-copper alloys is not well established in the respect to the two-liquid region. Fig I, taken from the 1939 Ed. of the ASM Metals Handbook, shows a two-liquid system existing above the liquidus temperature, but disconnected from it. Although Ruer and Fickl and Ruer and Goerensz definitely established the fact that two liquid layers could occur in the system, Ruer3 was not convinced that the line of immiscibility was closed in the center. Maddocks and Claussen4 found no liquid immiscibility at temperatures up to 157oOC in alloys containing almost no carbon. Although the diagram would indicate age hardening of the copper-iron alloys is possible, Hanson and Fords found that little hardening effect could be obtained. However, Gordon and Cohen6 reported that the response is better if the quenching is very efficient. Although iron has a potent effect on the conductivity of copper, Hanson and Fords have shown that, when hot-rolled copper-iron alloys are aged at 1200°F, the electrical conductivity decreases sharply with iron contents up to 0.2 pct Fe, and then levels off at conductivities between 60 to 70 pct IACS with compositions to 2.1 pct Fe. They also found that aging did not increase the tensile strength, although increasing iron content gave a moderate improvement in strength. High-strength copper-iron alloys, usually containing about 60 pct iron, had been reported by Smith and Palmer.7 They found that an alloy containing 56.4 pct copper, 0.21 pct magnesium, balance iron, would give a maximum tensile strength of 170,000 psi and an electrical conductivity of slightly over 35 pct IACS. The alloy could also be processed to have I50,000 psi tensile strength, and about 41 pct I.\CS conductivity. Decreasing the iron content increased the electrical conductivity, but the long mushy range during freezing of the alloy containing 10 to 20 pct iron made the production of good castings difficult. In spite of the difficulty encountered by Smith and Palmer with alloys of around 20 pct iron, it was decided to make a rather complete investigation of this type of alloy. As a result of this investigation, a method of alloying and fabricating copper alloys containing 10 to 15 pct iron was developed

Jan 1, 1949

By M. P. Dalton

THE problem at the Morning mill is to separate the galena, which contains a great percentage of the silver, from the sphalerite, making each into a commercial product. The ore as received from the nine is dumped into hopper-bottomed bins of 1200 tons capacity. These are divided into five sections, the first section being the regularly used section and the re-mainder used as a reserve bin. The ore is first passed through a 9 by 15-in. Blake jaw-crusher with an opening of 4 in. This allows a ham-mer head to pass through without damage. The crusher discharges to a conveyor that delivers the ore into a two-section punched-plate trommel screen with 1 ½ and 2-in. openings. The undersize is carried by means of conveyors to the mill bins. The oversize passes over a shaking feeder and through a spray or high-pressure water to a picking-belt, where waste and crude ore is hand-sorted. About 4 per cent of the ore by weight is picked out as waste, assaying about 0.6 per cent lead, and this is discarded over the dump. About 4 per cent of the ore by weight is removed as crude ore, assaying 10 oz. silver, 30 per cent lead, and S per cent zinc, and is shipped direct to the smelter. The remainder of the oversize from the picking-belt is con-veyed to a 4-ft. Symons cone crusher with 1-in. opening, which is interesting as a new introduction in this dis-trict. The machine consumes approximately 40 hp. and the pinion shaft travels 555 r.p.m. The horsepower is rather high, but the machine has an extraordinarily large capacity, and, due to the unique construction, there is no danger of tramp steel causing any damage, as in that case the discharge "opening" is automatically

Jan 7, 1927