Search Documents

By Jack M. Swales

Kermac Potash Co., the newest American entry in a rapidly expanding industry, has come on the scene with notable variations in conventional shaft-sinking and mining techniques. Located in the famed potash producing district east of Carlsbad, N. Mex., Kermac started up its mine in November, 1965, to supply ore to the company's 500,000-tpy potash crystallization refinery. In so doing, the company (1) drilled the first large diameter mine shaft in the potash industry and (2) has employed new continuous miners especially adapted for use in thin potash beds. REACHING THE ORE ZONE In its initial mine planning, Kermac, a partnership owned jointly by Kerr-McGee Corp. and the National Farmers Union Development Corp., considered it imperative that the shafts be sunk and equipped as soon as possible and that the mine be developed sufficiently to insure a constant ore feed to the mill when the unit was placed on stream. After examining the alternative sinking techniques available to it, the company decided to accept a proposal by Big Hole Drillers, Inc., to drill the shaft from the surface through various formations of sandstones, siltstone, shales, anhydrite, limestones, dolomite and salts to the potash ore zone.

Jan 12, 1966

By Frank Firmstone

IT is often desirable to obtain one or more accurate horizontal sections of a blast furnace after blowing out. Wishing to do this, last April, in the case of No. 4 furnace at Glendon, which had worn in a very remarkable manner, the method described below was employed, with very good results. A scaffold was fixed in the furnace, and on it was placed a drawing- board, covered with paper, the top of which was made level at exactly the height at which the section was to he taken. (Fig. 8.) The centre of the furnace (which had previously been found, and marked on a plank across the top) was laid off on it by dropping a plumb-bob from above, and a strong needle was driven into the board in the centre. By means of a straight-edge and two plumb- bobs, the line passing through the centres of the front and back arches was also drawn on the board. A pencil was fastened to a light wooden straight-edge at a known

Jan 1, 1875

By Frank Firmstone

It is often desirable to obtain one or more accurate horizontal sections of a blast furnace after blowing out. Wishing to do this, last April, in the case of No. 4 furnace at Glendon, which had worn in a very remarkable manner, the method described below was employed, with very good results. A scaffold was fixed in the furnace, and on it was placed a drawingboard, covered with paper, the top of which was made level at exactly the height at which the section was to he taken. (Fig. 8.) The centre of the furnace (which had previously been found, and marked on a plank across the top) was laid off on it by dropping a plumb-bob from above, and a strong needle was driven into the board in the centre. By means of a straight-edge and two plumbbobs, the line passing through the centres of the front and back arches was also drawn on the board. A pencil was fastened to a light wooden straight-edge at a known

By F. S. Norcross

DEVELOPMENT of the manganese deposits of Cuba is a matter of importance not only to those involved in this industry on the Island but to the United States steel industry and to our Nation as a whole. For years our domestic resources of manganese have been wholly inadequate, but the recent Cuban development points the way toward solution of this strategic mineral problem.

Jan 1, 1939

By Harry A. Wahl

Precent fracture design procedures are bared on the total fracture area created. A method to distinguish beI,,.ecn total area and [he propped or effective fracture area has not been available. This paper presents a solution to this problem, applicable to horizontal fractures. The difierences between effective fracture area and torn] area are demonstrared in example calculations. This work is hayed on experimentally determined transport efficiencier of solids in sand-liquid slurries. Newtonian and non-Ne~vtoninn systems are considered. INTRODUCTION Fifteen years after commercial introduction, hydraulic fracturing remains the most successful stimulation technique in the oil field. This success is primarily due to ability of induced fractures to penetrate and alter permeabilities deep within formations. Many fields producing today could not have been developed without the hydraulic fracturing process. Because of wide usage, fracture-treatment design has received a great deal of engineering and research effort. This work, resulting in improved equipment and materials, has increased the benefits from fracture treatments as well as the applicability of the process. A major contribution was the development of fluid-loss additives. Necessarily, the number of parameters to be considered in treatment design has steadily increased, resulting in more complicated design techniques. Almost all present design procedures are based on the precepts set forth by Howard and Fast. Relating the fluid volume lost into the formation, the volume required in extending the fracture, and the total slurry volume injected, they developed an expression for the total fracture area created in terms of pertinent treatment parameters. Fluid loss during treatment was expressed as a function of time for three flow mechanisms. Although modifications of fluid loss equations have been made, the total fracture area concept has remained unaltered. A vast amount of field data indicate that induced fractures must be propped and held open to be effective. A notable exception is the Mesa Verde formation in the San Juan basin. However, analysis of these treatments shows that improved well productivities are obtained when propping agents are incorporated in the treating fluid. Although propped fracture area has been recognized as an important design parameter, a method to distinguish between total area and effective fracture area has not been available. The necessary information on slurry-sand transport in fractures has been lacking. Interest in the propped region of induced fractures is not restricted to areal extent alone. The distribution of sand within fractures is important from the standpoint of fracture flow capacities. Flow capacity affects the increase in well productivity after stimulation. The work of Huitt and Darin4 hows that partial monolayers of sand have large flow capacities compared to thick* dense sand packs. It has been postulated that gelled fluids have the ability to transport sand within the fractures at the deired low concentrations. An early contribution in the area of sand placement in fractures was made by Kern et al.' They studied sand movement in a transparent vertical fracture model. It was observed that the sand tended to settle out in the bottom of the model before moving very far. When the fluid velocity exceeded a certain critical value, all of the sand injected began moving through the crack even though it settled to the bottom. This critical velocity was determined under several flow conditions. Some work on sand movement in horizontal fractures has been reported in Russian publications. Sand movement was studied by Izyumova and Shan'gin' using a transparent "pie-shaped" flow model to simulate a horizontal radial flow system. However, the data were limited, especially in a quantitative sense. Dorozhkin, Zheltov and Zheltow studied the behavior of sand-liquid slurries in a horizontal linear flow model. The quantitative data were restricted primarily to the thickness of sand deposits formed at the bottom of the fracture. An earlier paper provided basic data on the flow of sand in horizontal fractures. This study was designed to yield specific quantitative information on rate of advance of sand particles and pressure behavior under various flow conditions. A comprehensive photographic study was undertaken in a 10-ft windowed flow cell to provide the necessary qualitative and quantitative data. Since the number of potential variables far exceeded the capacity of the initial study, emphasis was placed on the effects of sand concentration, oil viscosity and oil flow rate. A detailed description of these experiments and the results are described in Ref. 9. However. the implications of this work on the fracture design calculations were not discussed. An analysis of these data as well as new data is provided in the following sections. EXPERIMENTAL RESULTS The primary objective of the experimental investigation was to provide information on the rate of advance of the solids in sand-liquid sturries. A 10%-ft long transparent

Jan 1, 1966

By Eldon C. Pattee

Variations of a very reliable geochemical field test for beryllium developed by Patten and Ward, have been adapted by the U.S. Bureau of Mines to facilitate rapid testing of reconnaissance samples and to aid in rapid examination of known occurrences. Although several qualitative tests for detecting beryllium have been described in the literature,1,2,3, the Patten-Ward4 morin geochemical field method has the advantages of being rapid and being quantitative for minute amounts of beryllium. In addition to the morin field method, Patten, in cooperation with Griffitts, have developed a contact- print method for determining beryllium in hand specimens.5 The semiquantitative method can be used for rapid screening of samples in exploration or reconnaissance work. The use of beads for fusing samples provides a more rapid test, but gives less accurate results than the method developed by Patten and Ward. The semiquantitative method, however, requires less equipment and combines three stock solutions into one reagent for easy application. Estimates of samples in the range from 3 to 1000 ppm varied from about 0.25 to 5 times the actual beryllium content.

Jan 5, 1965

By J. W. Koger, R. E. Hurnrnel

QUENCHED, bcc p brass, P1, transforms to a mar-tensitic phase, when it is cooled below room temperature.' This transformation can be followed using resistance measurements since the resistivity of the martensitic phase is considerably larger than that of the parent phase, Fig. 1.' phillips3 first reported that, when Cu-Zn alloys containing between 37.0 and 39.0 wt pct Zn were quenched from the 0 region to room temperature, variable amounts of a phase could be observed depending on the mode of quenching. If the quench occurs very rapidly, the a phase forms by a "massive transformation". The resultant phase has the same composition as the high-temperature P phase from which it was formed. If the quench is less severe, the alloy is retained largely in the p form; however, some a is formed by precipitation. In this case, a contains more copper than the high-temperature 0 phase from which it has formed. The a phase most probably does not undergo a transformation in the temperature range where p transforms to low-temperature martensite. This can be deduced from the Eesistivity-temperature relation which is linear in this temperature range, Fig. 2. The stable a phase which is present along with R. E. HUMMEL is Assistant Professor, Department of Metallurgical and Materials Engineering, University of Florida, Gainesville, Fla. J. W. KOGER, Junior Member AIME, formerly with University of Florida, is now with Oak Ridge National Laboratory, Oak Ridge, Tenn. Manuscript submitted December 13, 1967. IMD.

Jan 1, 1969

By G. R. Fitterer

NONMETALLIC inclusions in steel have received much attention by metallurgists during the past few years. Many investigators have been emphatic in stating their belief that these impurities are the chief causes of steel failures, while others think that their effects are negligible. One of the main reasons that definite information on the effects of these impurities is lacking is that no reliable method has been developed for the exact determination of the amounts of these different impurities in steel. Some valuable new information has been brought out by a reliable method for nonmetallic inclusions which has been developed at the Pittsburgh Experiment Station of the U. S. Bureau of Mines, in cooperation with the Carnegie Institute of Technology and the Metallurgical Advisory Board. This procedure satisfactorily extracts some of the more common inclusions from steels, thus enabling the investigator to correlate steel failures with inclusion content. Although the data given herein are the first to be published on the subject of the electrolytic extraction method, the interest in the subject is evidenced by the fact that it is already being used by some 20 to 30 steel companies for their various purposes. Some of the comments received from these laboratories indicate that the method is highly satisfactory: the unfavorable comments, when traced to their sources, have been found to be based on some small mistake made in either installation or operation. The chief discrepancy seems to have occurred in attempts to apply the method to the extraction of inclusions from alloy steels. The procedure can be used only for the plain carbon steels and for such low alloy steels as those containing the usual amount of copper (0.2 to 0.3 per cent). Steels containing the carbide-forming alloys such as chromium, tungsten, etc., present far too many difficulties for the accurate determination of inclusions. Luckily, the iron and manganese carbides do not offer any difficulties and no contamination of the oxide-sulfide residue results. It is highly probable that some modification of the following

Jan 1, 1931

By M. A. Schimmelpfennig, A. D. S. Gillies

Loss of visibility due to the occurrence of atmospheric fogging in underground mine airways can lead to longer travel times and loss of production efficiency, an increase in the frequency of vehicular and foot traffic accidents and difficulty in checking rock surfaces for instability and loose material. Where hot and humid surface air meets colder underground air, conditions for fog formation may be present. Further, suspended particulate matter from diesel exhausts or stoping operations together with slow movement of air along passageways may contribute to formation. This study describes an investigation being undertaken with the cooperation of Kennecott's Ozark Lead Co. to identify causes of the problem.

Jan 1, 1984

By AIME AIME

C. H. BENEDICT, chief metallurgist of the Calumet and Hecla Consolidated Copper Co., has pioneered for nearly half a century. Noted for his ammonia leaching process, lie has Iong been responsible for all Calumet and Hecla mill, concentrator, and reclaination plant flowsheets. His influence has spread far beyond his own organization. lie is dean of Lake Superior metallurgists and has contributed greatly toward raising his specialty-the country over-to an honored profession; not merely an honored profession but a profitable one for industry and the public. The leaching process which he developed in 1912 has, since 1915, produced for Calumet and Hecla 250,000 tons of copper from waste tailings at a cost per pound, in 1929, below five cents. It has yielded profits of $35,000,000. In the war just ended, this process proved the only one adaptable to the recovery of copper from gilding-metal¬clad steel strip, and Calumet and Hecla treated more than 50,000 tons of such scrap for the Government.

Jan 1, 1945

By Clarence P. Linville

A previous article1 by the authors contained a general description of the new roasting furnace herein described but it did not go into detail as to the metallurgical behavior or the results obtained. Believing that such information would be of great value, they have elaborated on the subject and have given many unpublished details. The furnace described applies the principle of roasting finely divided zinc-sulfide ores, now produced in large quantity by the flotation process, in gaseous suspension; that is, the ore particles are carried, in suspension, in a current of air and gaseous products of the roast. The relatively great fineness of flotation concentrate presents difficulties and problems of roasting in furnaces of the ordinary type; the fine ore is forwarded through the furnace in the form of a shallow bed and its very fineness leads to dense impervious bedding which prevents oxygen from reaching the interior of the bed, thus unduly lengthening the time of roasting and preventing the elimination of the last of the sulfur. The fineness of the concentrate, normally, should lead to a rapid and complete roast, for the speed of roasting is a function of the surface exposed to oxygen, which surface is greatest, per unit of weight, in very fine material. The difficulty in bed roasting is to get the oxygen to the particle. If the fine ore, during the roasting, could be freely suspended in oxidizing gases, full advantage could be taken of the great surface conferred by its fineness. This fundamental idea, of course, is not new, for the Stedtefelt furnace, familiar to the older metallurgists, is an example of it; but the manner in which this is accomplished may be new. The numerous efforts to roast in gaseous suspension show that the idea is attractive; in fact, an analysis would indicate that it is the most reason-

Jan 1, 1925

By Jack R. Elenbaas, Donald L. Katz

A radial turbulent flow formula has been developed which permits the computation of the pressure drop for radial flow in gas wells whether the flow is laminar, turbulent, or partially laminar and partially turbulent. Using the formula a complete back-pressure curve has been calculated and analyzed by a comparison with existing back-pressure curves. A procedure is presented for computing the permeability of the porous media when the porosity, sphericity and average particle diameter are known. Introduction Recent studies on the flow of fluids through porous media have provided new methods for computing flow under turbulent conditions. The present study was initiated as an investigation of pressure -drop computations for flow through porous sands in gas wells and as an analysis of present-day back-pressure tests. Although laminar flow exists in the producing formation of gas wells under normal flow rates, turbulent flow does take place adjacent to the well bore. As the flow rate is increased, turbulent flow exists further and further into the producing formation and under open-flow conditions in relatively deep wells a considerable portion of the flow through the sand will be turbulent. In order to calculate a complete backpressure curve for relatively deep wells without resorting to extrapolation of curves drawn from data obtained in back-pressure tests or calculations made in the completely laminar region, it was necessary to have some means of calculating pressure drop for flow through porous sands under turbulent conditions.4.6 As a result, a radial turbulent flow formula was derived from the equations recently presented by Brownell and Katz.1 A rigorous solution of this equation involves a trial and error graphical integration. By making the assumptions of average viscosity, temperature and compressibility factor of the flowing gas, it was possible to graphically integrate the relation for the general case of radial flow of gases through the porous sand of gas wells. A chart has been prepared relating the value of the integral to the radius of the well bore and to the Reynolds number of the flowing gas. The chart actually performs the graphical integration and the solution of the formula is then reduced to a simple trial and error calculation. A typical back-pressure curve is calculated to show the transition from laminar to turbulent flow. This paper will briefly describe the pro-cedurcs for computing flow through porous media, including a method for predicting sand permeability from porosity and grain size and shape. Flow through Porous Media Brownell and Katzl recently reported a correlation for computing flow of fluids through porous media by the use of an enlarged Reynolds number and friction factor in which the porosity of the bed is included as an additional prime variable. The enlargcd Reynolds number com-

Jan 1, 1948

By Donald L. Katz, Jack R. Elenbaas

A radial turbulent flow formula has been developed which permits the computation of the pressure drop for radial flow in gas wells whether the flow is laminar, turbulent, or partially laminar and partially turbulent. Using the formula a complete back-pressure curve has been calculated and analyzed by a comparison with existing back-pressure curves. A procedure is presented for computing the permeability of the porous media when the porosity, sphericity and average particle diameter are known. Introduction Recent studies on the flow of fluids through porous media have provided new methods for computing flow under turbulent conditions. The present study was initiated as an investigation of pressure -drop computations for flow through porous sands in gas wells and as an analysis of present-day back-pressure tests. Although laminar flow exists in the producing formation of gas wells under normal flow rates, turbulent flow does take place adjacent to the well bore. As the flow rate is increased, turbulent flow exists further and further into the producing formation and under open-flow conditions in relatively deep wells a considerable portion of the flow through the sand will be turbulent. In order to calculate a complete backpressure curve for relatively deep wells without resorting to extrapolation of curves drawn from data obtained in back-pressure tests or calculations made in the completely laminar region, it was necessary to have some means of calculating pressure drop for flow through porous sands under turbulent conditions.4.6 As a result, a radial turbulent flow formula was derived from the equations recently presented by Brownell and Katz.1 A rigorous solution of this equation involves a trial and error graphical integration. By making the assumptions of average viscosity, temperature and compressibility factor of the flowing gas, it was possible to graphically integrate the relation for the general case of radial flow of gases through the porous sand of gas wells. A chart has been prepared relating the value of the integral to the radius of the well bore and to the Reynolds number of the flowing gas. The chart actually performs the graphical integration and the solution of the formula is then reduced to a simple trial and error calculation. A typical back-pressure curve is calculated to show the transition from laminar to turbulent flow. This paper will briefly describe the pro-cedurcs for computing flow through porous media, including a method for predicting sand permeability from porosity and grain size and shape. Flow through Porous Media Brownell and Katzl recently reported a correlation for computing flow of fluids through porous media by the use of an enlarged Reynolds number and friction factor in which the porosity of the bed is included as an additional prime variable. The enlargcd Reynolds number com-

Jan 1, 1948

By O. T. Marzke, Robert F. Mehl

A study of the structures arising from the decomposition of the ß solid solutions in the Cu-Zn and the Cu-A1 systems is of peculiar interest in the study of the mechanism of precipitation from solid solutions. It is possible in these alloys, by varying the composition within the ß field, to precipitate from the same basic lattice phases having different lattice structures. It has been rather generally assumed heretofore that the type of structure originating from the decomposition of a solid solution— the Widmanstätten structure—-is determined by the lattice structure of the parent solid solution alone. In the first paper of this series1 evidence was advanced which threw doubt upon this hypothesis; but definite proof of the correctness or incorrectness of the hypothesis should be forthcoming from a study of these alloys, for if the structures originating, for example, from the precipitation of the a phase from ß and of the ? phase from the ß in the Cu-Zn system should be shown to be crystallographically different, the hypothesis would necessarily be held as definitely disproved. Furthermore, the newer proposal enunciated in the first paper of this series—that the origin of the Widmanstätten structure lies in a cooperation between the lattice of the parent solid solution and that of the precipitate-—which at present seems the only a1ternative hypothesis, would in such an event be given added weight. The work here reported shows that the Widmanstätten structures originating in the precipitation of the a phase from the ß and in the precipit'at.ion of the y phase from the y in the Cu-Zn system are indeed crystallographically different; and incidentally presents some new descriptive information on the Widmanstätten structure from a more general point, of view.

Jan 1, 1931

By M. M. Fine

Normally the U. S. produces less than 10 pct of its annual manganese requirement. About 95 pct of domestic consumption is used by the steel industry.1 The strategic and critical nature of manganese has been recognized by its inclusion in the national stockpile and by intensified research directed toward cataloging and evaluating domestic manganiferous deposits. The USBM has participated in these activities for many years with field and laboratory studies to assess the extent and potential utilization of domestic manganese ores. One area of particular interest is in the vinicity of Batesville, Ark., where deposits have been mined since 1849 for both manganese and ferruginous manganese ores. Production is centered in Independence County, but deposits are also found in Sharp, Izard, and Stone counties in north- central Arkansas. Miser has described the geology and manganese mineralization in some detail.2,3 The rocks of the area are sedimentary, consisting of sandstone, limestone, shale, and chert. The two formations of greatest importance,4 Fernvale lime- stone and Cason shale, are host rocks of the primary manganese mineralization.

Jan 8, 1959

By K. A. Jackson, J. D. Hunt

A new classification of eutectics is proposed, based on tlze entvopies of wzelting of the tuio eutectic phases. The clnssification was used to predict suitable tvansparent analogs of the metallic systems. Experimental confir?nation loas obtained for the theovetical shape of the lamellar solid-liquid interface, fov the fault mechanisms of lanzellar spacing changes, and for the development of low-energy solid-solid boundaries between the lamellae. An explanation is presented to account jov the irvegular and coinplex regular structures zrhich are found in some eritectic systems. FrOM experimental observations, single-phase materials can be divided into two groups according to their solidification characteristics, those that grow as faceted crystals and those that do not. acksonl' showed from thermodynamic reasoning that the type of growth depended on a factor a which was almost thg entropy of melting. Most nonmetals have high entropies of melting (a greater than 2) and grow with crystalline facets. Most metals have low entropies of melting (CY less than 2) and grow almost isotropically with no facets. The authors propose that eutectics may be classified in a similar manner. There are three groups of eutectics, those in which both phases have low entropies of melting, those in which one phase has a high and the other phase has a low entropy of melting, and those in which both phases have high entropies of melting. Lamellar or rodlike structures are formed in systems in which both phases have low entropies of melting. In these alloys dendrites of either phase may be formed, when the alloy is rich in the relevant component. Examples are Pb-Sn, Sn-Cd, Pb-Cd, Sn-Zn, Al-Zn. Irregular, Fig. 14((), or complex regular, Fig. 14(b), structures are formed in alloys in which one phase has a high entropy of melting and the other has a low entropy of melting. Examples are A1-Si, Zn-MgzZnll, Pb-Bi, Sn-Bi. When the alloys are rich in the low entropy of melting phase, dendrites are formed; when the alloys are rich in the high entropy of melting phase, faceted primary crystals are produced. These crystals are sometimes called hoppers or pseudodendrites. In this work the term dendrite will only be used to describe nonfaceted primary crystals. Dendrites are not formed during solidification in high entropy of melting single-phase materials. The third group of eutectics includes alloys in which both phases have high entropies of melting. Each phase grows with a faceted solid-liquid interface. Since most metals do not have high entropies of melting, metallic examples in this eutectic group are rare. However they may occur between some intermetallics and semiconductors or semimetals such as silicon, germanium, and bismuth. Attempts have been made to study eutectic solidification visually by watching the growth process.374 Since metals are not transparent, the observations had to be made on external surfaces. This difficulty can be overcome by using transparent analogs of the metallic systems. As was mentioned earlier, most single-phase compounds have entropies of melting greater than 2 and so grow as faceted crystals. Recently organic materials with entropies of melting less than 2 were investigated.' These materials grow in exactly the same way as the low entropy of melting metals. When the materials are pure, they grow with a solid-liquid interface parallel to an isotherm; when they are impure, cells or dendrites are formed. Since these materials are transparent, have low melting points, and even have cubic structures, they should be ideal for making up transparent analogs of the metallic eutectics. The purpose of the present work was to investigate these organic eutectics and to see whether this quite different series of eutectics could be classified in the same way as the metallic systems. The observations made on the organic alloys are also discussed with reference to the current theories of lamellar growth. Explanations are proposed to account for the structures formed in the other eutectic groups. EXPERIMENTAL Thin cells containing the organic alloys were uni-direction ally solidified on a specially constructed microscope stage.' Uniform growth rates were obtained by moving the cells, with a motor drive, through a fixed temperature gradient, so that the solid-liquid interface remained stationary with respect to the microscope objective lens. The cells were made by fusing two microscope cover slides 7/8 by 7/8 by 1/100 in. together on three sides, leaving a gap of 1 to 3 mils between the slides, and these were filled by surface tension. A preliminary investigation of the phase diagram between two components could be made very rapidly. One side of the cell was filled with component A and the other side with component B. Since only a small amount of mixing could occur every composition from pure A to pure B was present in the cell. When the cell was placed in the temperature gradient a pictorial representation of the phase diagram was obtained. Eutectics, peritectics, "interorganics", and solid -solid transformations could be readily detected. Fig. 1 shows part of a eutectic phase diagram. The Sample was first grown slowly then stopped. The two

Jan 1, 1967

By AIME AIME

FRIEND recently remarked that the career of Scott Turner is characterized by Work and Wild -A Ducks. To these might be added Accomplishment and Persistent Fishing. All of these elements are manifestations of his character. The diversions-hunting and fishing-are in the nature of the proverbial trolley conductor's holiday, for many of Turner's years have been spent in the outdoors, often in distant lands, as in Spitzbergen, where the ducks pictured below were bagged. The election of Scott Turner to the presidency of the Institute marks the culmination of a quarter century of membership, during the last two years of which he has been vice-president. He was born at Lansing, Mich., on July 31, 1880, and received his A.B. at the University of Michigan in 1902, with a B.S. and E.M. at the Michigan College of Mines in 1904. Since then he has been granted two honorary degrees, D.Sc. from the Colorado School of Mines, and D.Eng. from the University of Michigan, but he still prefers to be called "Scott" rather than "Doctor." Government service was not a new experience for Turner when he was appointed Director of the U. S. Bureau of Mines by Secretary Hoover in 1925, for his first employment after graduation was as Field Assistant in the U. S. Geological Survey in Oregon and Idaho. This was followed by work in Tombstone, Ariz.; then his first foreign engagement in 1905-6 as superintendent of the San Pablo Gold Mining Co. in Panama. Various field experiences followed, though there was an interlude in work of a kind that few mining engineers ever experience. This was in technical journalism, for in 1906 he was

Jan 1, 1932

By M. T. Halbouty

The Laredo oil district, South Texas, includes an area of approximately 200 miles long north and south and 75 miles wide, embracing the following counties: Starr, Zapata, Jim Hogg, Webb, Duval and McMullen. The area is relatively old in respect to the production of oil, as the first oil was discovered and produced in the Piedra Pintas field in Duval County on Sept. 10, 1905. Since that date, continuous new discoveries have contributed to the development of this district until, at the present time, it is one of the important oil-producing and gas-producing areas in the world. The year 1937 also had its share of new discoveries in the district, including not only new oil fields but also new sands in already producing pools and important extensions to existing sands and fields. Among the most important field discoveries, by counties, are: Duval County..... Benavides, Sweden, Thomas-Lockhart, Labbe and Lundell fields Jim Hogg County.. Las Animas field McMullen County. Ezzell field Starr County...... El Tanque field Webb County..... Killam and Oilton fields Of these, Benavides, Oilton, Killam and Ezzell have so far proved themselves most important; the Benavides field, Duval County, showing by far the most activity. For the year 1937, therc were 283 wildcat tests drilled in this district, of which 35 were oil producers, 20 completed as gas wells and 228 abandoned as dry holes. Duval County, as usual, received the greatest amount of wildcat drilling, having 21 oil wells, 5 gas wells and 63 dry holes completed during the year for a total of 89 tests. Next came Webb County with 4 oil wells, 4 gas wells and 53 dry holes for a total of 61 tests.The Laredo oil district, South Texas, includes an area of approximately 200 miles long north and south and 75 miles wide, embracing the following counties: Starr, Zapata, Jim Hogg, Webb, Duval and McMullen. The area is relatively old in respect to the production of oil, as the first oil was discovered and produced in the Piedra Pintas field in Duval County on Sept. 10, 1905. Since that date, continuous new discoveries have contributed to the development of this district until, at the present time, it is one of the important oil-producing and gas-producing areas in the world. The year 1937 also had its share of new discoveries in the district, including not only new oil fields but also new sands in already producing pools and important extensions to existing sands and fields. Among the most important field discoveries, by counties, are: Duval County..... Benavides, Sweden, Thomas-Lockhart, Labbe and Lundell fields Jim Hogg County.. Las Animas field McMullen County. Ezzell field Starr County...... El Tanque field Webb County..... Killam and Oilton fields Of these, Benavides, Oilton, Killam and Ezzell have so far proved themselves most important; the Benavides field, Duval County, showing by far the most activity. For the year 1937, therc were 283 wildcat tests drilled in this district, of which 35 were oil producers, 20 completed as gas wells and 228 abandoned as dry holes. Duval County, as usual, received the greatest amount of wildcat drilling, having 21 oil wells, 5 gas wells and 63 dry holes completed during the year for a total of 89 tests. Next came Webb County with 4 oil wells, 4 gas wells and 53 dry holes for a total of 61 tests.

Jan 1, 1938

By CLARESCE CARLETON SEJIPLE

(Wilkes-Barre Meeting, June, 1911.) AT a number of mines in eastern Nicaragua, 3.5- and 5-ft. Huntington mills are used for grinding gold-ore after a preliminary breaking in jaw-crushers. The smaller mills are made sectional to facilitate transportation to the more difficultly accessible mines. The capacity of the smaller mills is about 20 or 25 per cent. that of the larger, but in proportion to the quantity of ore ground they require more power and are subject to greater wear. The notes herein given are from records of the performance of the larger mills, but, in general, apply to the smaller also. THE NATURE OF THE ORE. The ore occurred as a series of flat veins in a highly-decomposed rock, probably alaskite. The primary mineralization comprised pyrite, pyrrhotite, marcasite, chalcopyrite, and quartz; the oxidation-products of which were chiefly hydrated iron oxide or limonite, chrysocolla, azurite, and malachite. The kaolinization of the feldspar of the country resulted in the admixture of a great quantity of clay with the oxidized ore. The quartz was sandy, imbedded in the clay; and probably the greater part represented the residue from the crushed rock in the fissures after leaching, and kaolinization of the feldspar. There was little vein-quartz in the unaltered primary sulphide ore. Only the oxidized ore was mined for the gold that it contained in amounts that averaged $4 per ton. No specks of gold were ever seen in the ore, and the gold obtained by panning was always exceedingly fine. The amalgamation-bullion was about 800 fine in gold and 60 to 80 in silver. The ore delivered at the mill contained from 5 to 15 per cent. of moisture; during the rainy season the quantity was much greater. The moisture and clay made the ore so sticky that it had to be raked over steeply-inclined grizzlies; it hung in the ore-bins,

Oct 1, 1911

By N. A. Elmslie

This subject covers much ground, therefore it must be treated in a general way rather than in detail in this paper. Personnel To approach the measure of a mine, it is, of course, essential that the personnel be measured, and this measuring must be done in a circumspect manner and conclusions must be reached slowly. There may be one unit in the personnel of an organization that may be out of step with the remainder of the organization, not always because of lack of ability, but because of misplacement or lack of proper measurement of his capabilities. Too much time can scarcely be spent in the study or measure of the personnel ; in fact, a manager or a superintendent of a mine never completes his work along this line. Mine or Plant Just as no two men are alike, so no two mines or plants are alike; and yet there are many similarities. Find out what the similarities are, and this will help to make clear the dissimilarities. Try to visualize details of the difficulties, not because you will have to deal with them yourself, but to consider them in later studies of general problems. To outline all the steps to be taken in familiarizing oneself with a plant or operation would be impossible, but the following points may be of interest in any investigation. The study of a mine is generally made backwards-—that is to say, one sees the finished product first-—-but this is immaterial, because each step must be considered separately in any event. As a rule, there are certain heads under which the different features of mining can be placed, as follows: Ventilation.—Ventilation is usually the most important item in power cost and safety, especially in gassy mines. Quantity of air, water gage and power consumption, and finally analysis of the return air in full return and separate splits should be considered. Type of fan and type of power unit should enter into this study because it is important to view expenditures which are going on 24 hr. a day and 36.5 days in the

Jan 1, 1931