Search Documents

By Terry Ramsey

INTRODUCTION The Cyprus Pima Mine is located 20 miles southwest of Tucson, Arizona and about fifty miles north of the Mexican border. The Cyprus Pima orebody was discovered in 1950. Feasibility studies were begun in 1952 employing underground development. Economic studies showed open pit operations to be feasible and stripping of overburden was begun in late 1955. The first ore was reached in October of 1956. A 3,000 tpd (tons per day) concentrator was completed and began operation January 1, 1957. From these beginnings, Cyprus Pima Mining Company has expanded into a plant processing approximately 54,000 to 56,000 tpd. Four expansions were required to bring the plant up to its present capacity. Each expansion incorporated what had been learned in previous operation of the plant. The first expansion was completed in August of 1963 doubling design capacity to 6,000 tpd. In reality, because of softer than average ore, capacity was closer to 8,000 tpd. Expansion II was completed in July 1966 bringing design capacity to 18,000 tpd. Expansion III followed immediately. Completed in the summer of 1967, this expansion increased the design capacity to 30,000 tpd. The actual dry tonnage of this portion of the operation in 1974 averaged 38,400 tpd, again, primarily as the result of treating softer than average ore. The latest expansion (Expansion IV), completed in December 1971 and utilizing a semi-autoge- nous grinding circuit, is located in a separate building (Mill II) approximately 200 yards southeast of the original mill (Mill I). Expansion IV was designed for 14,000 tpd, but after circuit modifications, averaged 16,500 tpd in 1974.

Jan 1, 1976

By P. D. I. Honeyman, P. A. Faust

At the Miami plant of the International Smelting Co., Inspiration, Ariz., there are four reverberatory furnaces, all 120 ft. long. At present only one of these furnaces is in operation. It is operated as a wet-charge furnace, the charge being distributed for about 65 ft. down the furnace length. Usually this charge contains about 12 per cent moisture and runs 25 per cent sulfur, of which there is eliminated in the furnace from 25 to 30 per cent. The furnace is oil-fired, the fuel being burned in a battery of Cananea-type, low-pressure burners. The flame is kept short and conditions so adjusted as to obtain complete combustion within the furnace. The average furnace draft, taken through the verb arch, amounts to only 0.02 in. of H2O. Draft is purposely kept low to cut down infiltration through the flues and boiler settings, and control dampers are regulated to maintain this uniform condition throughout the charging as well as the smelting period. Hot gases discharge from the furnace uptake through a common header flue to the waste-heat boilers. The general layout and dimensions of the plant are shown in Fig. 1. Four Stirling boilers, two of class M-26 (713 hp.) and two class M-31 (850 hp.), serve the furnace. Three usually are sufficient to take care of normal operation, the fourth boiler being used as a spare when necessary. The distribution of hot gases to the various boilers is regulated by the dampers in the boiler exit flues. Normally the boilers closest to the furnace uptake would evaporate more water than do those farther away, but dampers are regulated so as to distribute fairly well the load between the several boilers. Steam from the waste-heat plant is delivered to the adjoining power house of the Inspiration company, where it is used both in the Nordberg blowing engines and for electrical generation. Steam pressures and temperatures recorded are those in the main power-plant header and are thus inclusive of all losses in about 500 ft. of 10-in. line. Steam for smelter heating and auxiliary use is taken from the main waste-heat header, is reduced to 125 lb. and distributed through separate lines. Boiler feed water is supplied by the power plant and consists of returned condensate, augmented to a large extent by make-up water

Jan 1, 1934

J. Parke Channing, New York, N. Y. (communication tb the Secretary*):—Mr. Wright, in his introductory paragraph, says: "It is commonly believed by metallurgists that in copper-smelting, the copper in the slags, which is irreducible by continued smelting, is retained in the form of 'prills' of matte." On a recent visit to Greenwood, B. C., I was discussing with J. E. McAllister, the general manager of the British Columbia Copper Co., and the former metallurgist of the Tennessee Copper Go., this very question; and he held strongly to the idea that the copper in slag was in two forms—one portion contained in occluded matte and the other as an oxide. He believed that this same rule would apply to the silver in the slag. From my experience I am strongly inclined to agree with Mr. McAllister; and it appears quite reasonable that in furnaces treating oxidized copper-ores, and to a less degree in furnaces treating sulphide ores, there is always bound to be present a certain amount of copper oxide and silver oxide, which will behave like any base and get into the slag as such. We all know that in Arizona, in the early days, when it was customary to produce black copper, because the ores were nearly all oxidized or carbonates, and eulphur was scarce, the slags as a rule carried 2.5 per cent. of copper and seldom ran

Jan 1, 1911

LATEST estimates of Russian steel production for 1951 give rise to the belief that on at least one vital front, the Western bloc of nations has maintained a definite advantage. On the surface, we are outproducing the Eastern bloc by more than twice. The United Nations Economic Commission for Europe estimates Russian output at 31.30 million tons, a 15 pct increase over the previous year. Production for the entire Iron Curtain is figured at 40.93 million tons. Western Europe alone produced 17 pct. more steel during the same period. The figures are misleading in one sense. We have no precise idea of how much steel is being used for arms. The Western nations are still expending much of their production for consumer goods, and you cant throw washing machines in a shooting war. It is significant to note that Russian production is well, beyond estimates made by world authorities prior to the current international situation. INTERIOR Secretary Oscar L. Chapman warns that the United States must make use of the resources of other nations or face mineral impoverishment once the time of struggle is over. He pointed out that the present struggle between two ideologies can leave the United States in such a state as to preclude anything but political' victory-with an accomp anying economic loss that will be irreparable. Chapman scored the attitude whereby conservation programs are looked upon as a luxury, pointing out that the nation faces an ever increasing need for action on that front. He also announced that the Bureau of Mines doubled its facilities for producing pure zirconium during 1950-51 at the request of the Atomic Energy Commission. Zirconium may be an important structural metal for atomic power devices. The Interior Secretary also said that the AEC has provided the Bureau with funds for the study of radioactive minerals and to help test and evaluate about 9000 ore samples believed to contain uranium.

Jan 1, 1952

By John L. Schroder, D. L. McElroy

ALTHOUGH the earliest use of rubber-tired haulage was in Illinois in 1936, the first unit of this type of equipment used in West Virginia was shipped into the state in 1938. All units placed in West Virginia mines have been of the shuttle-car type. The Katherine Coal Mining Co., at Lumberport, W. Va., was the second company in the United States to install shuttle cars and the Gay Coal and' Coke Co., at [ ] Mt. Gay, W. Va., was the first company in the country to install the thin-bed type of shuttle car. On Oct. 8, 1940, nine companies in the state were using 41 shuttle cars, of which 10 cars at three mines were of the thin-bed type. All shuttle cars of the low type were in the southern fields and all of the high type were in northern West Virginia. At that time several units were in the process of delivery. The data in this paper were collected in the field by Mr. Schroder in connection with graduate work on mechanical loading of coal in West Virginia by mobile loaders. In the course of his field work he visited five mines in the state that were using shuttle cars. All of these mines were in high-volatile coal beds of strong structure. [ ] The more pertinent data obtained at the mines visited are given in Table I. The maximum distance of shuttle-car haul is the distance between the transfer station and the farthermost place. Tonnage per loading unit per foot of bed thickness is to some degree a measure of relative efficiency, especially if the different operations are working the same bed or have somewhat similar conditions. The thin-bed operation is well up in the higher bracket of the afore-mentioned column, which is as

Jan 1, 1941

By R. W. Harper, M. C. Fuerstenau, J. D. Miller

Data were obtained with hematite with octyl hydroxamate and oleate as collectors to determine the mechanism of collector adsorption and also to establish the roles that conditioning time and temperature assume in this system. The presence of hydroxy complexes of iron are apparently necessary for chemisorption of collector to occur, and it appears as if extended conditioning times and elevated temperature promote greater dissolution of the mineral and hence greater concentrations of hydroxy complexes. Data were also collected with two natural hematitic ores. With one ore that was ground to 70% - 15u, an addition of 0.4 lb per ton hydrox-amate resulted in a final concentrate recovery of 86% at a grade of 64% iron. Satisfactory concentrate grade could not be obtained with fatty acid under these conditions. The effect of conditioning time prior to the addition of collector was also examined with another ore. When the ore was conditioned for 3 min, 19% of the iron was recovered in the concentrate at a grade of 67% Fe. With a conditioning time of 7 min, 73% of the iron reported to the concentrate at a grade of 62% Fe. These products were obtained with an addition of 0.2 lb per ton hydroxamate. This ore also responded well to flotation with fatty acid. The use of potassium octyl hydroxamate as a collector for iron oxide has been the subject of an earlier study.1 From this initial study, it was suspected that hydrolysis of surface ferric iron was involved in collector adsorption. More recent work in other systems has shown that slight mineral dissolution, followed by hydrolysis of cations common to the mineral lattice, is apparently necessary, and that adsorption of these hydroxy com- plexes probably occurs prior to the adsorption of collector. In view of these facts, work has been continued on the hydroxamate-hematite and oleate-hematite systems to gain better insight into the mechanisms of collector adsorption on iron oxide. Microflotation experiments in conjunction with infrared analysis were used in this regard. In addition it was felt necessary to establish more clearly the responses that can be obtained from natural ores when hydroxamate is used as collector as compared to those obtained when fatty acid is used. Experimental Materials and Techniques Pure potassium oleate, potassium octyl hydroxamate, synthesized from hydroxylamine hydrochloride and methyl octanoate, and a distilled Tall Oil were employed as collectors. Conductivity water was used in the

Jan 1, 1971

By E. T. Knight, John D. Gill

Much has been written and said concerning the alleged wasteful and uneconomic use of natural gas and petroleum. Espccially condemned has been the use of natural gas for the production of carbon black and the use of heavy fuel oil under steam boilers.' The critics of these usages of gas and oil have sought to make effective their verbal attacks on the industry by the repetitive expression of the words "inferior" and "superior" uses2 of petroleum. Thus, to employ natural gas for residential heating was to use it in a superior way; to use it for the production of carbon black was to use it in a wasteful and uneconomic way. To use petroleum for the production of automotive fuel was to use it in a superior way; to employ it as a residential fuel and as the prime source of power in an industrial plant was to use it in an inferior and uneconomic way. No doubt the objections to such employment of gaseous and liquid natural hydrocarbons originated in the belief that natural gas and petroleum are limited, nonregenerative mineral resources, and that the functions they perform can be just as well performed by other natural resources like coal13 of which practically unlimited reserves are known. The generations that have dominated each of the last four decades have counted reserves4 of petroleum in terms of a few years supply. Meanwhile, domestic demand for motor fuel rose spectacularly from a few million barrels in 1900 to more than 500,000,000 bbl. last year.5 The more imaginative and vocal critics drew startling word pictures of the catastrophe of 25,000,000 motor vehicles made useless and of the great automotive manufacturing and allied industries brought to an untimely end, and millions of workers left hopelessly unemployed by what they called the deplorably rapid depletion of the petroleum reserve. Many of the critics have been sincere advocates of the conservation of natural resources; many others, and in recent years probably the majority, have espoused the doctrine of conservation to promote their own self-interest rather than that of the public. The latest advocate of severe restriction in the use of petroleum for the alleged purpose of conserving the petroleum resource proposes to achieve that end by a bill,6 now before

Jan 1, 1938

By K. Prins

ONE of the more pressing problems faced by the coal industry today is the development of adequate means for meeting conservation laws, particularly those involving stream pollution, in various parts of the country. Discharge of dirty coal washery water into streams and rivers is almost universally frowned upon. Many states have enacted laws carrying heavy fines to curb the practice. The Prins stream-cleaner is one of the latest machines to enter the market. It is closely related to the cyclone thickener in principle. Eleven stream-cleaners are currently operating, ranging in size from 4 to 16 in. diam. In more recent installations the water enters directly in line and on a tangent with the impeller. The impeller consists of a vertical shaft up through a packing gland and bearings, and a V-belt pulley. The lower part is a tubing fastened to the shaft above, extending through the water intake compartment and provided with six vertical flat bars welded to the tubing. Portholes are situated in the upper end of the tubing, immediately below the point where shaft and tubing join together. The portholes are placed so that they are in open communication with the upper compartment of the stream-cleaner from which the processed water is discharged. The impeller is motor driven with a wide range vari-pitch drive employed between motor and impeller. The motor is mounted vertically, and the mounting provided with a vertical hinge allowing for needed adjustment of the wide range vari-pitch drive. The dirty coal washery water entering the machine under 20 lb psi pressure, flows from the compartment above the impeller, between the impeller blades, and is whirled around in the vertical section of the impeller enclosure. The speed of the impeller supplies centrifugal force and velocity required for separating suspended solids from water. The lower part of the machine consists of a cone, whose action is similar to other machines of the same type. The underflow discharge orifice is a cold rolled steel block machined to correspond with the cone angle and allows insertion of steel tubes of different diam. On 16 in. machines a 1 ¾ in. ID vertical discharge pipe is used. Provision is made for attaching a curved section of the same diam to the vertical pipe, to which, in turn, different lengths of horizontal pipe can be connected. Curved Pipe Advantageous It has been found that a curved pipe offers resistance to discharged material flow. In addition, the rotary motion of the underflow can be easily arrested in a curved pipe. Impeller speed of the 16 in. diam machine is provided from 400 to 800 rpm. A speed of about 474 rpm is suitable for maintenance of a constant underflow in coal slurry. In one installation 5x ¼ in. coal is cleaned in a Jeffrey Baum type washer at a 225 tons per hr rate. Washer installation is of the conventional type and a drag type sludge tank is used for water clarification purposes. Capacity of the water system, including the Baum washer, is about 40,000 gal. Before placing the stream-cleaner in operation, it was necessary to flush out the entire system every five days of two shift operations. The only time the system is drained now is for repair work on the sludge conveyor or the rig. The suction line of the stream-cleaner pump terminates in a number of small branch lines located at a depth of about 4 ft above the sludge conveyor. Each branch line extends the full width of the tank and is provided with four intake ports, each one with a funnel shaped inlet projecting downward. The arrangement provides an extensive pick-up area, for dirty water, and the inlets are arranged for a low rim velocity, preventing the taking in of coarse particles. The funnels are also arranged to extend up or down in the tank. They are set to pick up -60 mesh material exclusively.' The material is a high ash and high sulphur product and thus has to be disposed in the refuse conveyor. The underflow of the stream-cleaner is discharged on top of the washery refuse which is carried in a drag type horizontal conveyor, discharging into another refuse conveyor inclined at 30º with a short horizontal loading section. Some Disadvantages The impeller inherits certain disadvantages because of the nature of its construction. Additional moving parts make it subject to wear and maintenance costs. The advantage of being able to maintain a constant speed, however, to produce desired water velocity in the machine outweighs the drawbacks. Better separation between water and solids can be obtained by regulating time of residence of water through adjustment of valves in the intake and discharge lines. The amount of fines encountered during plant operation will vary because of higher or lower moisture in coal passing over fine coal vibrating screens. Even the amount of fines picked up by underground loading machines will be inconstant. Consequently, the percentage of solids will vary in water to be processed. The velocity in the feedlines to the slurry thickeners will fluctuate, with the required water velocity lacking. Another advantage advanced for the machine is its ability to operate on 15 to 25 lb line pressures at the water intake, reducing pump power required and pump maintenance.

Jan 1, 1952

Jan 1, 1903

By Orson Shepard

THE term "electrocapillary amalgamation" is used in this paper to designate amalgamation processes that depend upon electrocapillary phenomenon; i.e., the action of an electric current upon the surface tension of mercury at the contact with aqueous solutions. Electro-capillary amalgamation is selected as a name for these processes because the electrocapillary phenomenon has been found to be the effective agent in the use of sodium amalgam, as well as in the various processes using an electric current from a source outside of the amalgam. Amalgamation processes that depend upon supplying an electric current to the amalgam from an outside source, such as batteries and generators, have previously been called electrical amalgamation processes. There has been a tremendous amount of experimental work done on amalgamation processes involving the use of an electric current, as shown by the large number of patents issued on these processes: the earliest in 1885 and the latest in 19341. Regardless of all the experimental work, the fundamental principles causing the operation of electrocapillary amalgamation processes have not been described. The explanation usually given is that an electric current keeps the amalgam bright and clean. Patent No. 328532 states: It is well known that when amalgam plates are used for collecting gold and silver from their ores the surfaces of these plates are liable to become tarnished or sickened by certain substances contained in the ores or in the current of water which is employed to carry the ore over the plates, and that in this condition they are unfitted for amalgamating the particles of gold and silver. To prevent this and to keep the surfaces of the amalgamation plates always bright and in a better condition for catching and amalgamating the particles of gold and silver I employ electricity in the following manner:. . . A similar explanation is given 49 years later, in patent No. 1953364: The sodium (Na) ions lose their charge at the cathode becoming sodium atoms, which do not react with the electrolyte, but follow the grounded electrical current through the mercury body producing in their passage sodium amalgam and liberate themselves in the amalgamation compartment when brought in contact with the fed

Jan 1, 1936

By Michael D. Martin

Pima Mining Co., managed and 50% owned by Cyprus Mines Corp., with Union Oil of California and Utah Construction and Mining Co. sharing equally in the remaining 50%, is a medium-sized open pit copper mine situated in the very active Twin Buttes mining district, 22 miles southwest of Tucson, Ariz. In 1965, a three-part paper described Pima's growth from 3,000 tpd (tons per day) in 1957 to 18,000 tpd nine years later. Within months of the completion of the last stage of this sixfold expansion, studies were being wound up on a further major expansion, this time to 30,000 tpd. This expansion is now a reality. Details of the enlargement of the crushing and concentrating plant have already been covered in a recent paper, and the present paper will cover pit engineering studies, equipment selection, and current operating practices. Key factors in top management's decision to go ahead with the latest expansion were: (1) a substantial increase in ore reserves coupled with an appreciable decrease in grade, (2) a generally favorable outlook for copper prices, and (3) better than expected performance by mine and mill equipment purchased for the expansion to 18,000 tpd. For the pit design studies, particular attention was paid to pit stability, a problem area at times in the past, and to the location and grades of the final ramp systems. In drawing up the long-term mining schedule, the attitude of the ore, with the higher grade material lying deeper, was a critical factor and considerable stockpiling of lower-grade material in the early years had to be accepted in order to keep the annual grades close to the average of the orebody. The expansion called for major purchases of mine equipment in order to gear up the mine for delivery of 30,000 tpd to the concentrator. In general, equipment chosen was of types already proven at Pima, al- though there were some exceptions to this practice. One of these excep-

Jan 1, 1969

Ira B. Joralemon, one of the world's most noted mining geologists, died last year at the age of 91. "His long professional career," says Donald H. McLaughlin, chairman of the executive committee at Homestake Mining Co., "covered an epoch in the history of mining that was unique in its opportunities and achievements," adding that many mining companies (Bunker Hill, Bralorne Mining, Copper Range, Anaconda, Newmont, Phelps Dodge, Homestake, etc.) greatly benefited from Joralemon's experience and wisdom.

Jan 12, 1976

By J. E. Nelson, R. J. Bonnis

Recent completion of Cyprus Bagdad's $240-million modernization and expansion program has registered a 700% increase in ore production with only a 50% increase in labor. Elements of this remarkable achievement include the application of large-scale mining equipment as well as the selection of the latest in processing hardware. Most important, however, was the early recognition that Bagdad's labor personnel is its most important asset.

Jan 4, 1978

1913. FRANDKA WBONA DAMS Montreal, Canada. 1921. WILLIAM CUTHBERTB LACKETT Sacriston, Durham, England. 1923. GELASIOC AETANI. Rome, Italy. 1929. TAKUMAD AN Tokyo, Japan. 1920. HENRYS TURGISD RINKER. Merion Station, Pa. 1922. FEDERICGIOO LITTI. Torino, Italy. 1906. SIR ROBERTA . HADFIELD. London, England. 1928. JOHNHA YSH AMMON.D. New York, N. Y. 1921. FRANKW ILLIAMH ARBORD London, England. 1917. HERBERTH OOVER. Washington, D. C. 1906. HENRI LECHATELIER. Paris, France. 1900. WALDEMAR LNDGREN Cambridge, Mass. 1879. JOHNM ARKLE .New York, N. Y. 1921. C. MCDERMID London, England. 1913. EZEQUIELO RDONEZ Mexico City, Mexico. 1909. ALEXANDRPEO URCEL Paris, France. 1911. ROBERT H . RICHARDS Cambridge, Mass.

Jan 1, 1929

THE following employment items are made available to AIME members on a nonprofit basis by the Engineering Societies Personnel Service, Inc., operating in cooperation with the Four Founder Societies. Local offices of the Personnel Service are at 8 W. 40th St., New York 18; 100 Farnsworth Ave., Detroit; 57 Post St., Son Francisco; 84 E. Randolph St., Chicago 1. Applicants should address all mail to the proper key numbers in care of the New York office and include 6c in stomps for forwarding and returning application. The applicant agrees, if placed in a position by means of the Service, to pay the placement fee listed by the Service. AIME members may secure a weekly bulletin of positions available for $3.50 a quarter, $12 a year. MEN AVAILABLE Sales Engineer, 37, seven years experience Europe and Latin America both in underground work and administrative and sales work; speaks fluent Spanish, Portuguese, French. Desires responsible position preferably export in U. S. M-692. Superintendent, 46, married. Experience covers mining and metallurgy as mining engineer and as general superintendent; metallurgy of leaching, flotation, cyanidation; development, construction, operation. Presently available. Prefer U.S.A. M-693-333-E-1-San Francisco. Mine Manager, Superintendent, Consultant, 61, married. Design and erection of mining and mill plants-examinations. Many years as superintendent, manager, consultant, designer and builder of mining plants, flotation mills, concentration mills. Available one month's notice. Prefer U. S. but foreign acceptable if good climate. M-695-4211-E-9-San Francisco.

Jan 1, 1952

By J. H. Westbrook

IT is always of interest to document the origin of real microstructures which closely approach various idealized morphologies. Such instances constitute excellent bases for experimental studies of the effect of microstructure on properties. Typical examples include the eutectoid steels (lamellae) used by many investigators and the two phase Cu-Cr alloys (spheres) recently employed by Hibbard and Hart The present note describes a structure with cylindrical particles. In a study of certain alloys in the Cr-C system, an alloy was arc melted whose composition was very close to the aCr-Cr,C, eutectic (3.2 wt pct C, according to the latest phase diagram published by Bloom and Grant2). The alloy was not analyzed but previous experience with the melting technique employed indicates good correspondence between intended and analyzed compositions with negligible tungsten contamination from the electrode. The phases present in the alloy were identified by X-ray powder patterns as a chromium and Cr,C,. Typical micrographs, presented in Fig. 1, show unmistakable evidence of the cylindrical geometry of the carbide phase. The eutectic grains are randomly oriented and, consequently, only a few show the true fibrous nature of the carbide particles, most being cut so as to show slightly elliptical cross sections. Within any particular grain, remarkable uniformity is to be observed with respect to the size, shape, spacing, and orientation of the carbide particles. Length to diameter ratios have been estimated from the micrographs to be at least 250:1, with diameters of about lp. This alloy may be of further interest from different viewpoints. On the one hand, it might be used to check the applicability of the equations derived by Fullman3 for computing true particle dimensions of cylindrical particles from opaque random sections. On the other hand, it might be possible to extract the carbide particles from this alloy and repack them in a ductile matrix to form a synthetic structure of the type discussed by Metcalfe et al.4 With the large l:d ratio and the small diameter of the carbide fibers, it is likely that the interdefect distance in each fiber is sufficiently great to permit realization of a large fraction of the presumed high strength of the carbide. References 1W. R. Hibbard, Jr. and E. W. Hart: Dispersion Hardening of Copper-Chromium Alloys. AIME Trans., 1955, vol. 203, p. 200; Joun-nal of Metals, January 1955. 2D. S. Bloom and N. J. Grant: The System Chromium-Carbon. AIME Trans.. 1950. vol. 188. p. 41; JouRnal of Metals, January 1950. aR. L. Fullman: Measurement of Approximately Cylindrical Particles in Ooaaue Samples. AIME Trans.. 1953, vol. 197, p. 1267; Journal of Metals. ~ebtember 1953 4 A. G. Metcalfe, C. H. Sump, and W. C. Troy: Fiber Metallurgy. Metal Progress, 1955, vol. 67, p. 81.

Jan 1, 1958

By C. R. Kuzell

STAFF: Editor, Gerhard Derge Carnegie lnstitute of Technology Schenley Pork Pittsburgh 13, Pa. Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: C. C. Long, President; John Chipman, Past-President; J. S. Smart, Jr., Vice-President, T. D. Jones, Treasurer; R. W. Shearman, Secretary. PUBLICATIONS COMMiTTEE OF THE METALLURGICAL SOCIETY: D. J. Carney, Chairman; Robert Maddin, Past-Chairman; J. H. Hollomon, J. H. Jackson, H. H. Kellogg, T. B. King, F. C. Langen-berg, D. L. McBride, W. O. Philbrook, J. S. Smart, Jr., R. L. Smith, J. D. Sullivan, and F. L. Vogel Review and selection of manuscripts is under the supervision of the following Publications Committees: Extractive Metallurgy Division: H. H. Kellogg, Chairman; T. 8. King, Post-Chairmon; R. P. Hermsdorf, W. A. Krivsky, R. E. Lund, C. L. McCobe, Poul Queneou, A. 5. Russell, M. E. Wadsworth, and W. D. Wilkinson. Institute of Metals Division: R. L. Smith, Choirman; P. A. Beck, I. I. Bessen, J. O. Betterton, Jr., R. S. Davis, J. J. Gilmon, R. 8. Gordon, C. D. Graham, Jr., R. W. Guard, J. C. Gurlond, J. J. Heger, M. Hermon, J. N. Hobstetter, H. H. Johnson, Jr., I. R. Krarner, W. C. Leslie, R. A. Meussner, R. R. Nosh, G. E. Pellissier, T. N. Rhodin, A. U. Seybolt, L. L. Seigle, I. S. Servi, P. G. Shewmon, L. Slifkin, J. K. Stanley, C. D. Starr, and J. Washburn. Iron and Steel Division: F. C. Longenberg, Chairmon; H. L. Bishop, C. W. Sherman, J. 8. Wagstaff, and E. Whittenberger. Published bimonthly by the American lnstitute of Mining, Metallurgical, and Petroleum Engineers, Inc., 29 West 39th Street, New York 18, N. Y. Telephone: PEnnsylvania 6-9220. Subscription $20 per year for nan-AIME members in United States and North, South, and Central America; $25, foreign; $5 far AlME members. Single copies, $4.00, single copies foreign, $5.00. The AlME is not responsible for any statement mode or opinion expressed in its publications . . . Copyright 1960 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . . . Registered cable address, AlME New York ...Indexed in Engineering Index, Industrial Arts Index, and Chemical Abstracts ... Second class postage paid at New York, N. Y., and Ann Arbor, Mich. Volume 218, Number 4

Jan 1, 1961

By Davis Baker

The direct-metal cars or ladles of the Maryland Steel Company have a capacity of 18 tons when filled within 12 inches of the top. On account of this large capacity, the formation of skulls in these ladles is by no means as rapid as in smaller ladles; but a skull once formed is a very unwieldy piece of metal to handle, and especially to remove from the ladle. We have found it cheaper to clean ladles often rather than make very heavy skulls. We aim to keep the ring of chilled metal that forms on the surface of the iron chipped off, so that the skull shall form principally at the bottom until it becomes so thick as to render the ladle unfit for service. Sometimes it happens that a ladle may be held for several hours filled with molten metal. This invariably leaves a large amount of chilled metal in the ladle. Frequently the skull will weigh several tons, and will be of the full size of the ladle inside, with a top crust, having perhaps a hole 12 inches square, through which the molten metal was poured. In order to remove skulls that cannot be easily chipped out with a bar, we use what may be called a skull-extractor, consisting of a hydraulic cylinder mounted in the center of a heavy cast-iron plate, standing vertically on a suitable foundation. Figs. 1 and 2 show the construction and operation of this apparatus, Fig. 1 being a view of the extractor with pistons extended to full stroke, and Fig. 2 a view with ladle in position and pistons about to commence the stroke. in both figures, A is the hydraulic cylinder, B the vertical cast-iron plate, and C the foundation. The water-pressure, admitted through the pipe, P, is 750 pounds per square inch, and the inside diameter of A is 14 inches. There are two pistons: D, fitting the bore of the cylinder, and E, 84 inches in diameter, moving inside of D. Both pistons move together when

Jan 1, 1893

By Max W. Ball

THE geologist or mining engineer, whose work takes him into the western United States, whether for the Government or private enterprises, is likely to be called upon to classify public lands as to their mineral character, or to review such classification already made, usually by a Government geologist or mineral inspector. The public-land law covering the matter is clear and logical, and a knowledge of its simpler principles is necessary to intelligent classification work. There are two classes of cases in which a classification of lands as mineral or non-mineral may be required: .first, cases in which lands classified as mineral will be retained by the Government and lands classified as non-mineral alienated; second, cases in which lands classified as mineral will be alienated and lands classified as non-mineral retained.

Jan 1, 1921

By Jay J. Burns

TWO zinc concentrating mills are operated by the St. Joseph Lead Co. in St. Lawrence County, N. Y. The Edwards mill is operating at present only sixteen hours a day treating 400 tons daily. The metallurgy at Edwards presents no unusual problems therefore this discussion is mainly limited to the metallurgy of the Balmat ore. The Balmat mill has a capacity of 1,250 tons per day and the operating crew consists of three shift bosses each with five millmen per shift. Two crusher operators work on each of two shifts and one cleanup man on day shift. The repair crew is made up of a foreman and three repairmen, one of the repairmen being capable of taking over any operating job in the mill from shift boss down. Each millman is capable of handling the next job in line and several men in the yard crew are broken into handling the start-off job in the mill so that temporary shortages of men do not cause extensive overtime. Sphalerite, pyrite, and galena, the principal ore minerals, occur in a gangue of calcite, dolomite, and silicates, especially diopside, plus tremo-

Jan 1, 1947