Search Documents

By Arthur L. Bishop

INTRODUCTION Purpose The in-situ leach method for uranium extraction is a relatively new and innovative method of uranium mining. In 1975, the first commercial in-situ facility began operation in south Texas. Since that time numerous other operations have been initiated as either pilot or commercial ventures. Considerable literature has been published that deals primarily with generalities of the process or environmental concerns. Several federal agencies have published documents which do not reflect the true operating or environmental nature of the in-situ leach method of uranium extraction. From an environmental standpoint, this is also evident in the promulgation of rules and regulations. Hence, the purpose of this paper is to present experience with an environmental concern--non- production zone excursions--such that the industry and the regulatory agencies will gain greater insight devoid of preconceived ideas and misconceptions. General Process Description In south Texas, in-situ leach mining is utilized to extract uranium from permeable sandstone ore deposits 61 to 213 meters (200 to 700 feet) below the surface. Uranium is present as an insoluble uranium oxide. In the in-situ or solution mining technique, anoxidizing lixiviant is injected into the formation through injection wells. The solution reacts with the insol uble carbonate complex. This soluble uranium complex is produced at recovery wells, each containing a submersible pump. During production there is a constant sweeping of lixiviant through the formation from the injection wells to the recovery wells. Injection and recovery wells can be arranged in any of a number of geometric patterns dependent upon ore body configuration, aquifer permeability, and operator preference. Submersible pumps in the recovery wells pump the uranium rich pregnant solution to the initial processing facility. Monitor wells surrcsund the pattern area and are screened in appropriate stratigraphic horizons (production and non-production zones) to detect any lixiviant migration that may occur (Fig. 1).

Jan 1, 1980

By M. W. Von Bernewitz

AN important regional meeting of the American Institute of Mining and Metallurgical Engineers was held, at Salt Lake City on Aug. 22 to 26, jointly with the fifth annual meeting of the Western Division of the American Mining Congress. The whole meeting was marked by enthusiasm, keen attention to the subjects under discussion, and many renewals of personal contacts. The trips to the various plants were well attended and the local press paid much attention to the meeting. The A. I. M. E. sessions began Aug. 23, with a non-technical morning session. J. 0. Elton, manager for the International Smelting Co., presided. The purpose of this session was to present in a non-technical manner the relation of flotation to mining, smelting, and the State. Ernest Gayford, metallurgist with the General En-gineering Co. of Salt Lake City, gave the definitions of flotation as suggested by Rickard, the dictionary, Weinig, and Taggart. The active agent in flotation is the air bubble, and the two prime requisites are the formation of bubbles and the creation of selective action of the bubbles for metallic particles instead of for gangue particles. Broadly, all the sulfides are floatable minerals, but the oxides, carbonates, silicates and sulfates are not. As far as Utah is concerned, flotation has been one of the greatest means of conserving its natural re-sources, because it has converted millions of tons of waste rock into pay ore; it is recovering millions of pounds of metal formerly lost in tailings; it has con-verted the zinc from a liability into an asset; and has kept thousands of men at work and distributed millions in dividends for the benefit of the State. As to the future of flotation, Mr. Gayford can con-ceive that the next 5 or 10 years may see as much, if not more, advance than was made in the preceding period. The big problem is dressing oxides, carbonates, silicates, and sulfates, and simplification of the number of reagents, also the separation of different gangue min-erals from one another.

Jan 10, 1927

By R. C. Gifkins, K. U. Snowden

The value of the index n in power ktivs for the stress sensitivity of minimum creep rale at lead is derived front results drawn from lite literature and from previously unpublished nork on commercial (99.99 pel) and high-purity (99.999 pel) lead polycryslalline and hi crystal specimens. In tests al 0.5Tm (22 to 50'C) for slvesses below 250 psi, n fulls to mily for poly-cr,yslullirle specimens, single crystals, and bicrystals, and toy grain boundary sliding in bicrystals. Between 250 and 500 psi there is a tyansilion range and, for the polycrystalline specimens al least, u high-stress regime for 500 to 1500 psi where n is 5 or 6. These results are such that none of the suggested stress taws can he used to extrapolate to very loir stresses. Meclianisms for deformation in Ike grains and toy grain boundary sliding in the low-strcss regime are outlined. In particular, the mechanism for grain boundary sliding involves sliding controlled by diffusion from tensile to compressire Ledges. predictions based on this model give promising numerical agree-nicul with experiment. II is suggested that the mechanism for grain boundary sliding may he important in other circumstances, e.g., in creep of ceramic materials or superplaslicity, because it can operate with lille or no dislocation aclirity. WhEN the stress dependence of secondary creep rate is represented by a power law the values taken by the stress exponent n are found to vary between 1 and 7, see, c.g., Garofalo.' In Eq. 1 11 u is the applied stress and A a constant. The case for accepting values of v = 1 rests principally upon tests at high temperatures (>0.9Tm) and there have only been isolated tests at lower temperatures (rather than plots of creep rate against stress) for which the creep rates are such that some form of Nabarro-Herring creep with n = 1 is applicable. Hanson5 and Greenwood and cole6 plotted creep rate against stress for tests made in the vicinity of 0.5Tw, and found a "creep yield", so that below a certain low stress the creep rate was linearly related to stress: these observations appear to have been subsequently ignored. Various models have been proposed which agree with a large body of experimental results in which n equals -5 at high stresses (e.g., weertman7 and McLean8). Various alternatives to Eq. [1] have been proposed principally as a means of unifying creep data, but sometimes, it seems, in order to obviate the necessity for assuming a series of regimes of deformation associated with the various values of n; further refer- ence to these will be made in the section on stress laws. This paper calls attention to extensive results which show n = 1 for the creep of lead at room temperature (0.5 T,). RESULTS Fig. 1 is a composite diagram based on figures in the literature6,9,10 with additional results obtained by the present authors and their colleagues11,12 in the course of a number of investigations not directly concerned with stress sensitivity. In Fig. 1 In creep rate is plotted against In stress. The curves show results for two kinds of material. Lead I is of commercial purity (99.99 pct Pb) and lead IT a specially refined material, hydrogen-purified to remove oxygen; it contains 99.999 pct Pb. Curve A is for lead I in polycrystalline form (grain diameter 0.02 to 0.05 cm) at room temperature (22' to 26°C). Curve B1 is for lead I, polycrystalline, tested at 50C. Curve B2 is for lead 11, polycrystalline (grain diameter 0.02 cm), tested at room temperature (22 O- Curves C to F relate to tests made of bicrystals of lead 11: all of the same nominal orientation ("Y" in Ref. 12). Curves C and V are for creep within the component crystals of the bi crystals at 22°C (AB and CD in Fig. 2). Curve E is for creep measured in a gage straddling the boundary, approximately 0.15 mm either side (BC in Fig. 2). Curve F shows rates of grain boundary sliding (as distinct from strain rates in the other curves), obtained by averaging the offsets of six marker lines on the bi-crystal boundaries. The principal feature of the results is that the stress sensitivity falls into two distinct regimes, according to whether the stress is below approximately 250 or above 500 psi (there is a transitional range between 250 and 500 psi). The new result is that below -250 psi two of the curves (A and BI) give a value of n 1, and the other curves also drop below n - 2 to -1.5 but do not extend to low enough stresses to show clear evidence of n 1. At very high stresses the curves tend to give values of n - 6, as previously determined in other investigations. Curve R2 for the high-purity lead in polycrystalline form at room tenlperature almost merges with B, and thus gives new significance to the values for stresses of 150 and 200 psi; previously'3 these points had seemed to fall away from the curve of slope -3, but they now can be seen as almost completing a transition to n = 1. It should be noted that there was originally considerable apparent scatter in the results for the high-purity lead. However, this was found to be associated with annealing conditions or variations in residual content of oxygen and curve B2 was constructed using the highest rate (i .e., the rate for the purest lead) determined for each stress during the course of various investigations over the years: altogether, some forty tests were used in constructing curve R2.

Jan 1, 1968

By J. V. W. REYNDERS

IN THE remarks which I am about to make concern¬ing the safety work of the Bureau of Mines, I want first of all to disengage myself from a disposition, which is frequently in evidence, to give spectacular emphasis to the hazards of mining operations. It is of the' utmost importance to the industrial welfare of our country that the enormous annual requirement of fuel be produced and be made available in our economic activities, with a minimum of distress and hardship. The safety of coal mining is a condition with which. we are all concerned in a fundamental way. And yet we should not rush to accept hastily conceived notions that laxity among employers in respect to safety measures exists to any outstanding degree. In fact in a large number of instances, the precautionary efforts of min¬ing companies, directed to the elimination of accidents are beyond all criticism, albeit the industry suffers in reputation from the carelessness of, its less effi¬cient constituents. The Bureau of Mines has been a leading influence in disseminating the doctrines of safety, in securing the cooperation of the miners themselves, and in stirring up ' the laggards, both among the employers and the employed. It is much to the interest of well-conducted mine operations that the industry, as a whole, observe safety regulations to the utmost.

Jan 1, 1925

By M. D. Hassialis

THE object of a technical paper is to communicate new technical knowledge, the paper being the vehicle of communication and the existence of new knowledge its reason for being. It follows that the development of information worthy of communication, the criterion being novelty, is prerequisite to exercising the privilege of communication. The act of communication is achieved when the reader perceives the nature of the new knowledge, i.e., when he understands it. A paper achieving this objective is an acceptable technical paper. Development of new knowledge has as one of its purposes the increase of the existing state of knowledge and the enjoyment of the benefits derived therefrom. Technical knowledge is a collection of facts so ordered as to make apparent, relations existing between the facts. When the interrelations have been exposed the facts have been interpreted or explained Three broad, overlapping categories of technical papers may be recognized: papers consisting of (a) a report of facts, (b) an explanation of facts, or (c) a combination of a report and an interpretation. Ideally a technical paper should belong to one of the last two categories but current practice is to accept papers belonging to any of the three categories. Based on a small sample drawn from the scientific and engineering literature, the relative frequency of the three types is a: b: c:: 20:1:14. If the sample be limited to engineering literature, the ratios become a:c::2:1; type (b) being nonexistent. This large departure from the ideal is a consequent of the

Jan 1, 1948

By J. Hunter

LouisiaNa ranks fifth among the oil-producing states. In 1941 the state-wide production was slightly in excess of 118,000,000 bbl. of crude oil and conden-sate—an increase of 15,000,000 bbl. over the total production for the year 1940. During 1941, south Louisiana produced approximately 90,900,000 bbl. of oil, while north Louisiana produced approximately 27,000,000. South Louisiana, therefore, produced about 3¼ times more oil than north Louisiana. During the past year, 574,800,000 M cu. ft. of natural and casinghead gas were produced in Louisiana; thus 1941 gas production exceeded the 1940 production by 104,900,000 M cu. feet. Completion records for the year 1941 show that 1512 wells were completed in or adjoining producing fields. These wells, which were drilled to extend known producing areas or were located within producing areas, are not considered as wildcat wells. Of the total number of field wells drilled, 1152 wells found production; the remaining 360 were junked or dry and abandoned. This means that 76 per cent of the wells drilled were successful. Considering the precarious nature of oil-field development, this percentage of new producing wells is exceedingly satisfactory. Of the total number of field welis com-pleted as producers, approximately 86 wells found new and distinct producing sands. During the past year, 30 new fields were found. Four parishes—namely, Caldwell, Catahoula, Orleans, and Natchitoches— entered the ranks of oil-and-gas-producing parishes in the state during that period. This brings the total number of oil-and-gas-producing parishes in the state up to 48. Thus, 75 per cent of the parishes in Louisiana now contain one or more oil and/or gas fields. Although sufficient data are not available to list the addition reserves found in Louisiana during 1941, it is felt that such reserves undoubtedly exceed twice the total production for that year, or at least 200 million barrels. In reserves, therefore, Louisiana ranks third among the various oil-producing states. South Louisiana Although 16 new fields were found in south Louisiana, the outstanding developments in that part of the state were not limited to new discoveries. In fact, most of the increase in reserve in that area has been most consistently accumulated through extensions of known producing sands and through the finding of new sands in already productive fields, especially at depths below the presently producing sands. Since data concerning most of the new extensions and sands are too extensive for discussion here, the more important developments arc briefly outlined below: Abbeville, Vermilion Parish.—Production extended ½ mile to the west. Anse La Butte, St. Martin Parish.—New oil sand discovered at 9400 ft., thus extending production to east flank. West flank defined by dry holes. Barataria, Jefferson Parish.—New oil sand discovered on east side of field at 7620 ft. New

Jan 1, 1942

By J. Hunter

LouisiaNa ranks fifth among the oil-producing states. In 1941 the state-wide production was slightly in excess of 118,000,000 bbl. of crude oil and conden-sate—an increase of 15,000,000 bbl. over the total production for the year 1940. During 1941, south Louisiana produced approximately 90,900,000 bbl. of oil, while north Louisiana produced approximately 27,000,000. South Louisiana, therefore, produced about 3¼ times more oil than north Louisiana. During the past year, 574,800,000 M cu. ft. of natural and casinghead gas were produced in Louisiana; thus 1941 gas production exceeded the 1940 production by 104,900,000 M cu. feet. Completion records for the year 1941 show that 1512 wells were completed in or adjoining producing fields. These wells, which were drilled to extend known producing areas or were located within producing areas, are not considered as wildcat wells. Of the total number of field wells drilled, 1152 wells found production; the remaining 360 were junked or dry and abandoned. This means that 76 per cent of the wells drilled were successful. Considering the precarious nature of oil-field development, this percentage of new producing wells is exceedingly satisfactory. Of the total number of field welis com-pleted as producers, approximately 86 wells found new and distinct producing sands. During the past year, 30 new fields were found. Four parishes—namely, Caldwell, Catahoula, Orleans, and Natchitoches— entered the ranks of oil-and-gas-producing parishes in the state during that period. This brings the total number of oil-and-gas-producing parishes in the state up to 48. Thus, 75 per cent of the parishes in Louisiana now contain one or more oil and/or gas fields. Although sufficient data are not available to list the addition reserves found in Louisiana during 1941, it is felt that such reserves undoubtedly exceed twice the total production for that year, or at least 200 million barrels. In reserves, therefore, Louisiana ranks third among the various oil-producing states. South Louisiana Although 16 new fields were found in south Louisiana, the outstanding developments in that part of the state were not limited to new discoveries. In fact, most of the increase in reserve in that area has been most consistently accumulated through extensions of known producing sands and through the finding of new sands in already productive fields, especially at depths below the presently producing sands. Since data concerning most of the new extensions and sands are too extensive for discussion here, the more important developments arc briefly outlined below: Abbeville, Vermilion Parish.—Production extended ½ mile to the west. Anse La Butte, St. Martin Parish.—New oil sand discovered at 9400 ft., thus extending production to east flank. West flank defined by dry holes. Barataria, Jefferson Parish.—New oil sand discovered on east side of field at 7620 ft. New

Jan 1, 1942

By E. A. Holbrook

AS A whole, engineering schools have not awakened A to the fact that the workmen compensation laws passed in most of our states between 1914 and 1917 effected a quiet but none the less real revolution in. the relations between labor and management; no longer are industrial accidents unfortunate or careless happenings over which we feel a humanitarian interest and sorrow, they are a cost of the process and the finished product, as vital as improved design and increased efficiency. Last year the writer and others made a committee report to. the American Institute of Mining and Metallurgical Engineers on the cost of accidents in the coal industry of Pennsylvania. Comparatively the accident record in Pennsylvania coal industry is not high, yet the direct compensation cost plus the interference with operation cost of accidents was over 5 per cent. of the total cost of producing the coal. This stands out more vividly -if you realize that about 70 per cent. of the' cost of producing the coal is for payment of labor, wages that are fixed and over which engineering efficiency and management skill have little or no direct effect. This leaves 30 per cent. of the cost chargeable .to hoisting, haulage, overhead 'and other items subject to engineering control. One sixth of this is due to cost of accidents. Surely a direct place 'for an engineering attack.

Jan 1, 1925

By Oliver Bowles

AUTOMOTIVE TRANSPORT by highway, which has become indispensable to modern life either in peace or war, involves the use of powerful machines, many of which travel at high speed. To start, accelerate, and stop each motor vehicle demands the use of clutch and brake. Friction is applied intensively to both these mechanisms, and their linings must therefore be of materials that will resist wear and that will not ignite with the heat of friction. Asbestos, that curious fire-resisting: natural fiber that may be woven into unburnable cloth, is eminently suitable for this special' use, and no satisfactory substitute for it has yet been found Because- asbestos is regarded as absolutely essential to all types of motor transport on land, and in addition is indispensable to. many .other kinds of machines and equipment, the situation of the- United State's with respect to supplies of-raw-material-is of special interest: From the standpoint of national self-sufficiency, conditions are far, from satisfactory, for United States mines furnish only three to four percent of the total domestic require-

Jan 1, 1938

By E. R. Johnson

The copper concentrator of the Braden Copper Co. is at Sewell, Chile, on the westem flank of the main Cordillera of the Andes, at an air distance of approximately 50 miles southeast of Santiago, the capital of Chile. The region is mountainous and space is at a premium because of the rough terrain and the danger of snowslides. The ore, a porphyry copper, is mined by a block-caving method in the El Teniente mine. It is hauled to the crushing plant, a distance of 2.6 miles, through a tunnel because of the severe climatic conditions. The usual large, coarsely set, primary reduction machines found in many ore-treating plants are not required because of the mining method employed and the limiting 12-in. spacing of the grizzlies at the head of each ore pass in the mine. It is the purpose of this paper to describe the numerous improvements made in the crushing section of this large flotation concentrator during the past I5 years to increase the efficiency of the plant and to raise the daily output from around 20,000 to 30,000 tons. The reader should keep in mind that all changes were made within the existing building because of the limited space and the high cost of the heavy mill construction required to withstand the snow loads. The present plant, as well as the former, operates on a 24-hr, 7 days a week basis. The crushing plant commenced operations at its present site in 1921, the main equipment being No. 7½ gyratories, followed by 48-in. horizontal Symons disk crushers. Fines were removed by I-in. stationary grizzlies ahead of each unit. In 1924 a third stage of crushing was provided by the addition of 55½-in. rolls in open circuit. During 1925, the Symons disks were replaced by 73½-in. rolls. All the rolls were changed to closed circuit, with elevators and screens to give a final product of 9 pct plus 3-mesh. The flowsheet of a typical crushing section of this period is shown in Fig I. The ore was withdrawn from a common bill serving the five crushing sections in the plant by means of any number up to six 36-in. wide-apron feeders, which discharged onto a common conveyor belt. This conveyor was equipped with a magnetic head pulley and the crusher attendant was stationed near the discharge end to pick out pieces of mine timber that might be in the ore. The ore was discharged over a 13/4-in. spaced bar grizzly and the oversize of this grizzly was crushed by a No. 7½ McCully gyratory crusher set at 13/4-in. opening on the closed side. The grizzly undersize joined the gyratory discharge and was conveyed to a set of 73½ by 20-in. Garfield rolls set at I in. These rolls operated in closed circuit with a bucket elevator and two vibrating screens placed in parallel.

Jan 1, 1949

GENTLEMAN: The year 1928 was another in the history of the Institute which was marked by quiet growth and steady progress. The total membership as of December 31, 1928, was 8703 as compared with 8438 on December 31, in 1927. Again the main increase has been in Members and the number of Junior Associates is less. As will be seen also by the Treasurer's report, the increase is reflected in larger receipts for dues indicating that fewer have had to be dropped for non-payment. There has been a gratifying increase in the number applying for reinstatement and it seems clear that interest in and attachment to the Institute has notably increased. The year was signalized by the merging of the Rocky Mountain Club with the Institute which brought to our roll one hundred and forty who were not previously members from among the men who have made the West. It also brought to the Institute a strong tradition of good fellowship and a fund of over $100,000, the interest from which is to be expended so far as may be, for purposes beneficial to the Western states. The Endowment Committee expects to see other and similar funds entrusted to the Institute and the Board has already appointed a special committee to consider all projects for expenditure of the revenue from them. It is felt that with the organization and personnel available in the Institute even modest revenues can be made to yield large returns in the way of scientific and technical knowledge. Within the year also, a third great Division has been organized within the Institute, building on the foundation of the old Iron and Steel Committee. The new Division signalized its independence by joining the Lake Superior Mining Institute in a visit to the Menominee Range in September and by furnishing material for a special volume of 353 pages, "Iron and Steel" Technology in 1928," printed and distributed in December. The Institute of Metals Division held its fall meeting with good attendance as one feature of National Metal Week at Philadelphia in October, and published its volume of Proceedings, running to 836 pages, in August. "Petroleum Development and Technology in 1927," 844 pages, came out in June and recorded the work of the Petroleum Division. A most interesting Fall meeting was also held by the Division at Tulsa,

Jan 1, 1929

NEW MEMBERS The following list comprises the names of those persons who became members during the period Oct. 10, 1918, to Nov. 9, 1918. ALLER, FRANK D., Copper Met., Ore Purchaser, American Smelt. & Refin. Co., 120 Broadway, New York, N. Y. AVÈRY, PAUL W., Met. Engr., Esperanza Min. Co., Apt. 8, El Oro, Mex., Mexico. BAKER, CHARLES A., Leaching Foreman, Copper Leaching Plant, Anaconda Copper Min. Co., Anaconda, Mont: BREED, CHARLES H Met., Crown Cork & Seal Co., Baltimore, Md. CHASE, R. L., Min. Engr 102S First National Bank Bldg., Denver, Colo. EICHELBERGER, FRANK, Vice-pres. and Engr., New York-Montana Testing & Engrg. Co., Helena, Mont. GESTER, G. C., Geol., Standard Oil Co. of Cal., 616 Standard Oil Bldg., San Francisco, Cal. GRIFFIN, JOHN, Mgr., Anthracite Territory, The Dorr Co., Board of Trade Bldg., Scranton, Pa. HAYNES, ELWOOD Pres., The Haynes Stellite Co., Kokomo, Indiana. Hsi, T. C:.. Sec'y, Tayeh Iron & Steel Works, Tayeh, China. HYDE, AUSTIN T., Mgr., Keokuk Plant, River Smelt. & Refin. Co., 607 Franklin St., Keokuk, Iowa.

Jan 12, 1918

By Marcel Daly

THE writer has devoted a number of years to practical operations and to the study of geology in the oil fields. In consequence, he has been brought to investigate the theories advanced to account for the accumulation of oil and gas in commercial deposits. It is the result of these investigations and his personal conclusions that he wishes to sum up in this paper. The writer is an advocate of the organic origin of petroleum found in pools. He has been led to believe that the present theories of oil and gas accumulations are incomplete and, in certain respects, incorrect, although they may embody certain elements of truth; that the forces that are called upon to explain the movement are only secondary forces in the process, and insufficient, by themselves, to cause this movement; and that the phenomenon of accumulation is of much larger order than heretofore admitted and bears an intimate relation with the general as well as with the local deformations of the crust and is a direct consequence and a mechanical effect of these deformations to which the term "diastrophic" has been applied. As a complement to this theory, the writer offers a new interpretation of the "rock pressure" and of the mechanism of the "sealing up" of this pressure in oil and gas pools.

Jan 7, 1916

By H. D. Strain

Potash is a generic term used to describe a number of compounds containing the element potassium (K), which is one of the three major plant nutrients. Potash content of these compounds is commonly expressed as percentage potassium oxide (K20), and the market value of the products is usually dependent on contained K20. Most of the potash produced (approximately 95%) is used in agriculture as fertilizer. Potash products today are shipped by producing countries all over the world to meet the need for increased food production. WORLD POTASH RESERVES Apparent world potash reserves are shown in Table 15.2B.1 and total some 96 billion mt of recoverable potassium oxide. The Canadian reserves account for approximately one-half the known world reserves. The reserves shown represent the potassium oxide content of a variety of potash-bearing ores. The major ore is sylvinite (a mechanical mixture of KC1 and NaCl) from which KC1 or sylvite is recovered (63.2% K20 equivalent). Other ores, such as langbeinite (potassium, magnesium sulfate-22.7% K20) and carnallite (potassuim magnesuim chloride-17.0% K20) are also mined in various parts of the world, mainly for the potassium content. Theoretically, potassium is available in almost unlimited qualities from brines and saline waters. To date, the cost of recovery from salt brines has been greater than the costs by mining operations, but new technology could make brines and seawater an increasingly important source. POTASH PRODUCTION Potash production dates back to the 1860s in Germany, which was the only recorded producing country until 1912. By 1912 Germany was producing approximately 1 million tpy of K2O equivalent. Production began in France in 1913 and in the United States in 1915. World potash production and consumption are shown in Table 15.2B.2 for the years 1950-51 through 1967-68. In 1967 and 1968 the major potash-pro¬ducing countries in order of importance were those listed in Table 15.2B.3. By 1972 Canadian production had outstripped U.S. production. WORLD CONSUMPTION World consumption of potash for the years 1950-51 through 1967-68 is shown in Table 15.2B.2. Table 15.2B.4 shows total world consumption of potassium materials in 1967-68 by country. More than 70% of the world's potash is

Jan 1, 1976

By Thomas T. Read

The cost of labor turnover in industry is so large as to justify the adoption of almost any means to bring about its reduction. Intensive study has shown that faulty methods of hiring and discharging men is the most important factor in labor turnover. Complete control over hiring and discharging by the foreman is a relic of outgrown industrial conditions; centralized hiring permits this work to be put on a scientific basis and also does away with many serious evils that cannot, otherwise be reached. Centralized hiring does not impair the authority of the foreman; he hires his men from the employment office and discharges them back to it, instead of from and to the street. The employment manager, being a direct representative of the employer, tends to restore the former relation of direct intercourse between employee and employer that was helpful in avoiding friction between them. Being a specialist,, he is able to bring special knowledge and skill to bear upon the task of selling employment in his concern to desirable workmen; he is also able to give the foreign workman the special attention he requires. Employment managers have been used for the past few years by a number of large organizations, a few of which are engaged in the mining and rnetallurgical industries. They have invariably reduced labor turnover, in some cases to as little as one-tenth of what it had been. So great a reduction is due in part to other changes made in the light of the data made available by scientific study of the labor problem. In my former paper on personnel work' I advocated the more general use of the employment manager in mining and metallurgical enterprises as a means of reducing labor turnover. The form of organization recommended seems not be to understood by all, and I have requested the privilege of explaining it at greater length, since it is perhaps the most important factor of all in personnel work, and has a vital influence on the cost sheet of every industrial enterprise.

Jan 1, 1918

By J. Parke Channing

These days of great industrial and social problems in America produce many suggested solutions and great changes. The practical engineer and employer of labor views these problems differently from the labor leader or the social reformer, but as never before he is sincerely interested in solving them in a way that will be just to all. The inevitable tendency of the day is toward "industrial betterment," " safety," '(industrial education," " efficiency," and the many other things which have become so familiar to progressive employers. There is no longer any question that these things are worth while from both the human and economic standpoints. They "pay" in dollars and cents. The very center of final success in improving conditions and increasing the efficiency of workingmen must be the spirit of fairness and a knowledge on the part of the employer of how to deal sympathetically and intelligently with his employees. Every progressive employer knows how greatly he desires foremen, superintendents, managers and others who possess these qualities. On the other hand, we are all familiar with serious mistakes made by young graduates of engineering schools who have had no opportunity to develop these qualities, and who have no real appreciation of the worth of the workers. Indeed, one wonders whether much ill-feeling, labor difficulties, and many strikes could not be avoided if such men had the right attitude. Is there any way of remedying this condition? If this particular difficulty can be solved, if these young engineers, many of whom are our coming leaders of industry, can be given the right perspective and the right understanding of these other problems in addition to fair, sympathetic methods of handling men, many of our other problems will be solved—not at once, but gradually and permanently, as these men make good and become influential in paths of industrial righteousness and industrial peace. Many progressive employers of to-day have enlarged their own perspective and realize the great importance of enlarging the perspective of those who shall follow them. How can it be done? For seven years a movement has been making

Jan 1, 1915

By V. E. Christensen

AT most smelting plants, forced draft, induced by high stacks or fans, is used to carry the gases away from the furnaces, roasters, or sintering plants. Gases moving under forced draft carry varying amounts of solids in the form of dust and fume. Where the weight of the solids is material, and the metal content high, it is usually profitable to treat the gases to recover these solids. Baghouses, Cottrell treaters, and settling chambers are the common forms of plants used to recover solids from gases. To check on the efficiency of these plants it is necessary to know the volume of gas leaving the plant and the amount of solids carried by the gas. As the volume of gas is equal to the product of the velocity of that gas and the cross-sectional area of the flue, the determination of the volume includes the measurement of the area of the cross section and the determination of the velocity. The velocity is generally measured by means of the Pitot tube and Ellison differential pressure gage, although low velocities are best determined by means of an anemometer. The dust concentration is determined by passing a measured volume of sample through a filter and weighing the dust caught. From this the dust concentration per unit of volume may be calculated. It is necessary to assume that the gas is homogeneous or that each cubic foot of the gas contains the same weight of dust as every other cubic foot. Having the volume of gas passing through a flue per unit of time, and the dust concentration of the gas per unit of volume, the amount of solids may easily be calculated.

Jan 1, 1935

By Julian M. Avery

In its dual role of pig-iron smelter and gas producer, the blast furnace is a remarkably satisfactory and efficient apparatus. Many metallurgists and engineers have pointed out, however, that since the primary function of the blast furnace is to produce pig iron at the lowest possible cost, its function as a gas producer should be subordinated to this primary purpose. During the past 10 years or more, improvements in blast-furnace technique and economy have, in fact, been directed primarily to increasing efficiency in the use of the reducing power of the gases produced by combustion of coke at the tuyeres, to reduce iron ore within the furnace. The net over-all result is a decrease in the fuel value of the top gas per unit of volume, and per ton of pig iron, which is evidently more than offset in value by the corollary saving in coke and the possibility of increased furnace capacity, for otherwise there would be no point in making such improvements. The purpose of the present paper is to suggest that, while progress has been made in this direction, there is another approach to the problem of increasing the chemical and thermal efficiency of the blast furnace in its primary role as a pig-iron smelter, which appears to offer possibilities of improvement in over-all ecorlomy of a different order of magnitude than results thus far obtained by the use of other expedients. The present argument is based in large part upon the hypothesis that the efficiency and economics of pig-iron smelting are seriously and adversely affected by the phenomenon known as "solution loss," and that the problem of solution loss call be successfully attacked by increasing the over-all pressure; i.e., the "top prcssure" under which the furnace is operated. It is indicated that pressure operation may also be expected to result in concomitant benefits, which may be summed up as generally improved operating conditions, together with a substantial saving in fuel and/or a substantial increase in furnace capacity. In a broad sense, the suggestion of pressure operation of the pig-iron blast furnace is not new, for operation under moderately increased over-all pressure was suggested as early as 1871, by no less an authority than

Jan 1, 1938

By Julian M. Avery

In its dual role of pig-iron smelter and gas producer, the blast furnace is a remarkably satisfactory and efficient apparatus. Many metallurgists and engineers have pointed out, however, that since the primary function of the blast furnace is to produce pig iron at the lowest possible cost, its function as a gas producer should be subordinated to this primary purpose. During the past 10 years or more, improvements in blast-furnace technique and economy have, in fact, been directed primarily to increasing efficiency in the use of the reducing power of the gases produced by combustion of coke at the tuyeres, to reduce iron ore within the furnace. The net over-all result is a decrease in the fuel value of the top gas per unit of volume, and per ton of pig iron, which is evidently more than offset in value by the corollary saving in coke and the possibility of increased furnace capacity, for otherwise there would be no point in making such improvements. The purpose of the present paper is to suggest that, while progress has been made in this direction, there is another approach to the problem of increasing the chemical and thermal efficiency of the blast furnace in its primary role as a pig-iron smelter, which appears to offer possibilities of improvement in over-all ecorlomy of a different order of magnitude than results thus far obtained by the use of other expedients. The present argument is based in large part upon the hypothesis that the efficiency and economics of pig-iron smelting are seriously and adversely affected by the phenomenon known as "solution loss," and that the problem of solution loss call be successfully attacked by increasing the over-all pressure; i.e., the "top prcssure" under which the furnace is operated. It is indicated that pressure operation may also be expected to result in concomitant benefits, which may be summed up as generally improved operating conditions, together with a substantial saving in fuel and/or a substantial increase in furnace capacity. In a broad sense, the suggestion of pressure operation of the pig-iron blast furnace is not new, for operation under moderately increased over-all pressure was suggested as early as 1871, by no less an authority than

Jan 1, 1938

By J. B. Neale

FRom the beginning of its activities, the members of the National Production Committee have felt that the following points were essential to the success of its work: The operators must feel that their operations were not 100 per cent. efficient; that they should be courteous and fair in their treatment of their employees; and that they should set an example of hard work and patriotic interest in increased production. Every move made must appeal to the sense of fairness of all parties concerned. The men must feel that in working more faithfully, and consequently producing more coal, they are rendering a distinct service to their Government in the time of its great need. As the workers feel that greater efficiency on their part results only in greater profits to the operators, the advantage to the operator should be lost sight of, as far as possible, and the advantage to the Government in fighting the war emphasized. Both operators and workers should know that the Government considered increased production an obligation, and opportunity for service, resting on both parties and not on the operators or the workers alone, and that both parties could very much better the efficiency of the pre-war period. Had the committee intimated that it thought the coal shortage was due entirely to the idleness and inefficiency of the workers, its campaign would have failed, for the men would have resented the charge because only too frequently their efforts to produce more coal were thwarted by bad management; besides, the operators would have lacked stimulus to better effort. On the other hand, had the impression been given that the committee thought that the coal shortage was due entirely to bad management, the operators would have resented the charge because only too frequently their efforts to produce more coal were thwarted by the idleness and inefficiency of the workers; and the workers, having been thus indirectly pronounced 100 per cent. efficient and patriotic, would have lacked stimulus to better effort.

Jan 1, 1920