Search Documents

By John K. Dienes

The permeability of sands and soils seems to be adequately de- scribed by Darcy's law, but the permeability of rocks is complicated by a number of factors related to the probability of crack intersections. During the last few years we have developed a statistical theory of fragmentation which has been successful in explaining the observed behavior of rocks. In this paper, a theory of permeability is developed which draws on the concepts employed in previous work. The permeability involves three factors, the average fluid flux per crack, the number of cracks per unit area, and the fraction of cracks that are not isolated. Probabilistic ideas are used in connection with the hydrodynamic theory of flow through a single crack to develop an integral expression for permeability. The result has the form of Darcy's law for anistropic media. Although the current work is motivated by the need to develop optimized oil-shale retorts, we believe that the theory can be applied to a variety of other problems.

Jan 1, 1982

By A. Eiders

THE year 1874 marks a decided advance in the metallurgy of the West, in two directions. On the one hand, the technical management has been very materially improved, and on the other, the production has been largely increased over that of the previous year. The technical improvements of greatest importance are the introduction of condensation-chambers, or flues, at several works, and the further treatment of the lead matte produced in the ore smelting. These two are of general importance, and although by no means introduced at the majority of works, their adoption at the few where their great importance has begun to be understood will no doubt bring about their universal introduction. To these may be added a third step. forward, which for some localities is vital enough, though for others it must still remain doubtful whether it is to be regarded as an improvement or not. This is the introduction, at several

Jan 1, 1875

By Francisco Cadena

THE construction of Norris Dam, built by the Tennessee Valley Authority on the Clinch River, a tributary of the Tennessee River, involved the production of coarse and fine aggregate for approximately 1,000,000 cu. yd. of concrete. A hammer-mill plant for the manufacture of sand from quarried rock was indicated as the most economical method of providing this material. The abrasive character of the feed as compared to the average hammer-mill feed made it necessary to control operations rather ciosely, and this resulted in the accumulation of many data bearing on production and maintenance. This paper will deal only with three specific sets of data, accompanied by such general infor-mation as may be necessary to explain the conditions under which they were obtained and followed by discussions on the relation of silica content to hammer wear, comparative costs of slugger and stirrup hammers, and comparative costs of tool-steel and manganese-steel grate bars.

Jan 1, 1937

By F. M. Lewis, R. B. Bhappu

In 1977 a paper was presented which reviewed the cost trends in producing copper by conventional processes for five years, 1972 through 1976. In this paper these costs have been updated to include the years 1977 and 1978.

Jan 1, 1982

By L. D. Jaffe

IN 1945-1946, the author measured temper brittle-ness in ingots of varying composition prepared by remelting SAE 3135 bar stock under vacuum. Since other investigators1-" have been referring to this hitherto unpublished work, belated publication seems worthwhile. Steel in 7 lb batches&apos; was induction melted with nickel additions in a magnesia crucible under a pressure of 10 microns of Hg or less and cast into a 2 in. diam chill mold. The compositions of ingots A, B, and C prepared in this way are shown in Table I; the vacuum melting lowered carbon, manganese, sulphur, and nitrogen content. Ingot B was homogenized 24 hr at 1095°C; ingots A and C were not homogenized. Blanks, M in. square, were cut from each ingot, austenitized 1 hr at 870°C, water quenched, tempered 1 hr at 595"C, and water quenched. Half the blanks from each ingot were given an embrittling treatment of 50 hr at 455°C and water quenched. A few specimens, embrittled and unembrittled, were finally heated 1 hr at 580°C and water quenched. Charpy specimens machined from the blanks were V-notched on the side closest to ingot mid-radius and paired as to radial position in the ingot, one of each pair having received the embrittling treatment and the other not. Specimens were broken in a standard impact machine at various temperatures, the same temperature, in general, being used for both bars of a pair. Fig. 1 shows the results. It is evident that temper brittleness, as measured by the increase in temperature of transition from brittle to tough failure introduced by the 455°C treatment, was decreased but not eliminated by reducing carbon to 0.006 pct, manganese to < 0.004 pct, and nitrogen to 0.001 pct. In another study," temper brittleness was apparently eliminated by -reducing carbon to 0.003 pct, with 0.80 pct Mn and 0.0015 pct N (ingot D)." • Analyses given for carbon below 0.02 pct were made by Jensen method; for nitrogen, by Kjehldahl method. Values quoted else-where&apos;-&apos;." for carbon content of ingot C and for nitrogen content of ingot D were obtained by conventional combustlon and by vacuum fusion methods, respectively, and are considered much less accurate. The 580°C final treatment removed previous em-brittlement (ingot B particularly), indicating that this was "reversible embrittlement."" Metallographic examination of ingot C with 1 pct nital etch revealed only ferrite; ingot A had carbide spheroids uniformly distributed in a ferrite matrix. With ethereal picric acid plus zephiran chloride etchant.&apos; no differences between embrittled and un- embrittled specimens of ingots A, B, or C were noted. Fracture of C and D below the transition temperature was predominantly transcrystalline, with traces of intercrystalline, in both embrittled and unembrittled conditions. The corresponding fracture of unembrittled B was mixed transcrystalline and intercrystalline; of embrittled B, predominantly intercrystalline with some transcrystalline areas. . . . Acknowledgment The efforts of J. C. Leschen, formerly of National Research CO~P., in preparing the ingots are acknowledged with thanks.

Jan 1, 1956

By H. I. Aaronson, C. Wells

THIS is a preliminary report on a detailed metal- lographic investigation of the bainite reaction in a plain carbon hypoeutectoid steel. In view of the current interest in the bainite reaction and of the controversies which still exist about even the basic phenomenology of this mode of transformation, it was considered desirable to present a summary of the more important results obtained to date prior to the completion of this investigation. The steel used contained 0.29 pct C, 0.76 pct Mn, 0.25 pct Si, 0.005 pct P, and 0.007 pct S. The alloy was homogenized for 48 hr at 1250°C. Individual specimens were then austenitized for 30 min at 1300°C and isothermally transformed for various times at temperatures above and within the bainite region, ranging from 775" through 500°C at intervals of 25°C. These specimens were carefully examined on a research metallograph; a few specimens of especial interest were also studied electron microscopically.&apos; Bainite may be defined as the aggregate structure resulting from the precipitation of carbides from supersaturated ferrite which formed by nucleation and diffusion-limited growth. Two groups of experimental observations made during the present study provide support for this mechanism of the bainite reaction: 1—at 625°C, partial conversion of pro-eutectoid ferrite to bainite began after more than 99 pct of the austenite had decomposed and 2—the precipitation of bainitic carbides occurred only within the ferrite phase. The proeutectoid ferrite and the bainite reactions in the steel studied were found to be morphologically continuous. Following the classification scheme of Mehl and Dube,2 three principal morphologies of proeutectoid ferrite were identified in the temperature region (625" to 550°C) in which the two reactions blend—grain boundary allotriomorphs," * Grain boundary allotriomorphs are crystals which nucleate at and grow preferentially along matrix grain boundaries. Widmanstaetten side plates, and intragranular plates. Carbide precipitation converted these morphologies into their bainitic equivalents with increasing isothermal reaction time. Conversion took place more rapidly as the reaction temperature was reduced. The replacement of supersaturated ferrite by bainite, however, did not occur uniformly even within individual austenite grains and was noticeably incomplete at higher transformation temperatures, e.g., 625° to 575°C. The ferritic and bainitic forms of a given morphology thus were frequently found to coexist, often inextricably intermixed, in a given specimen. At 625" and 600°C, the conversion of ferrite to bainite was clearly seen to have occurred entirely by the nucleation of carbides at ferrite/ferrite boundaries, as shown in Fig. 1. The nature of the loci at which carbides formed at lower temperatures was often difficult to ascertain with a light microscope, although the alignment in rows of many of the carbides, illustrated in Fig. 2, suggested that nucleation had again occurred at grain boundaries or subboundaries within the ferrite. Application of the electron microscope confirmed this deduction for bainitic structures formed at these temperatures, as shown in Fig. 3. The dense black appearance of bainite formed at very low reaction temperatures in higher carbon steels3 indicates, however, that isolated lattice defects within ferrite crystals prob-

Jan 1, 1956

By Charles Trotter

An instrument has recently been developed for determining the inclination and azimuthal direction of boreholes. This instrument is known as the Tro-Pari Instrument and is the invention of C. Trotter and G. Pajari of Sudbury, Ontario. Description The instrument is characterized by a unit mounted in gimbals and provided with a clockwork mechanism to clamp a compass to indicate azimuthal direction and simultaneously to clamp the unit in its plumb position to indicate inclination (Fig I). By means of a timing ring suitably calibrated in 5-min divisions, the unit may be set to lock after a lapse of time sufficient to allow the placing of the instrument at the desired point in the drill hole where readings are to be taken. The maximum time Lapse obtainable with the instrument designed for use in EX or AX size holes is I hr 30 min which is considered to be ample time to lower to the greatest depths that may be drilled with this size of equipment. Larger sizes could be developed for larger diameter holes such as BX and NX sizes or the larger oil-well sizes and a correspondingly greater time lapse could be provided for. Up to the present time only the EX-AX size has been built. Operation Assuming a borehole is to be surveyed at 1000-ft depth and assuming it will take 30 min to lower the instrument to this depth, the timing ring is rotated through seven divisions which represent a time lapse of 35 min (5-min leeway) and is then returned to its zero position. This operation imparts energy to a spring which drives the clockwork mechanism. Simultaneously the compass needle is freed to swing to its magnetic north-south position and the encased mechanism is freed to hang plumb within a semicircular portion of the frame which is graduated in degrees after the fashion of a protractor. This semicircular protractor portion has a V-shaped notch at each degree division of its inner periphery. The instrument, now in its free position, is inserted in a bronze container made to suit the size of hole to be surveyed (Fig 2). Soft rubber washers are provided within the container to prevent undue shock. The container is connected to the drill rods with three 5-ft lengths of brass or aluminum alloy rods separating it from the steel rods in order to prevent distortion of the magnetic field. The assembly is then lowered to the desired point where readings are to be taken and is allowed to remain at rest until a period of time has elapsed slightly in excess of the time for which the timing ring was set. In the example cited above, when the 35 min has elapsed the compass needle is locked in its north-south position and the protractor locking pin is extruded and locks in the V notch opposite its plumb position. The device may now be removed from the borehole and it will remain in this locked position in spite of jarring or shak-

Jan 1, 1949

By D. W. Gentry, H. E. Sherer

Determining the age at which to replace a specific piece of mining equipment, and choice of the best possible replacement, is a problem common to nearly all mining operations. This paper examines the data required for intelligent equipment replacement decisions and discusses how to predict future repair cost from historic data, determine the total cost of various replacement alternatives, and evaluate the different replacement alternatives. Various operations research and computer methods were used to develop this easily-used, practical equipment replacement method.

Jan 1, 1984

By R. L. Fleischer, R. S. Davis

BICRYSTAL specimens grown from the melt have been used extensively for investigations of the influence of grain boundaries on plastic deformation. The bicrystals are usually of predetermined orientation prepared by seeded growth from the melt in milled graphite boats. This technique has been described in detail by Chalmers.&apos; Since the direction that the grain boundary follows during growth is affected by both thermal conditions and crystallography, a difficulty arises in maintaining the grain boundary position constant along the length of the specimen. This problem is particularly

Jan 1, 1960

By N. J. Grant, I. S. Servi, A. Chaudhuri

IN a recent paper by Servi and Grant,&apos; it was illustrated that the slip band spacing and stress based on creep test data were related by the equation: d =1/ where d is the spacing in millimeters and v is the stress in psi, based on a more complete equation proposed by Orowan. It was shown further,&apos; that for a. given grain size, the slip band spacing became larger with decreasing stress (and was independent of temperature), until such time that the slip band spacing becomes greater than about one-half the grain diam- eter. When this occurred, the mechanism of deformation in creep of 2s aluminum at high temperature changed from slip to grain boundary deformation (sliding). Additional metallographic evidence is now available which confirms this in a most interesting fashion.

Jan 1, 1954

By A. Sainato, E. Baker, J. Cervik

In Europe, water infusion is used widely to reduce generation of respirable dust during mining. Its use in the US is limited to a few plow operations in the deeper parts of the Pocahontas No. 3 Coalbed. The technology for infusing water into retreating longwalls is described and results of a recent Bureau test in the Lower Sunnyside Coalbed demonstrated dust reductions ranging from 47% to 64%. Because water infusion increases moisture content of the coalbed, face air velocities in excess of 2.5 m/s (500 fpm) are possible, further diluting dust levels before dust entrainment occurs. An economic analysis shows a 23% reduction in operating costs when coal production is increased by changing from unidirectional to bidirectional mining with water infusion.

Jan 1, 1986

By Robert L. Wilson

Computation of reserve tonnages, stripping ratios, and grade of ore has long been a revolting aspect of the young mining engineer&apos;s job. Weeks at the desk calculator may turn into months before a single job is completed. Then many additional hours are necessary to check the calculations. During the last decade, computing machines have been widely publicized as instruments which will accomplish fantastic feats. Tales of their magical qualities have overshadowed their most basic characteristics-that of being a labor-saving device. Prior to a discussion of the electronic calculator&apos;s use on a mining problem, it may be well to point out that these machines are neither magic nor will they replace the judgment of an experienced engineer. In short, the "mighty morons," as the computors are sometimes called, are excellent labor savers but must be used correctly. They are not a substitute for thinking.

Jan 6, 1961

By R. L. Curfman

WHEN the Uranium Reduction Co. mill was put on stream in October 1956, one of the many operational problems was that the sand-slime separation circuits could not produce a satisfactory RIP feed, inasmuch as production greatly exceeded de- sign capacity. The original cyclone portion of the circuits consisted of two stages of three 14-in. cyclones in each circuit, as shown in the condensed flowsheet. The high percentage of +325 mesh material in the over- flows of these 14-in. cyclones was not consistent with good operation, and flow rates per ton of ore were high, indicating that not enough of the total solids in the ore was being rejected as sands. It was inferred by members of the metallurgical department that returning the underflows, or sand fraction, from these cyclones back into the drag classifiers was the primary reason for dirty feed.

Jan 7, 1958

University of Washington, Engineering Experiment Station, Seattle, Wash For bulletins and reports address the Director. Of the many Bulletins and two Reports issued by the Engineering Experiment Station the following are of most direct interest in this directory:

Jan 1, 1933

By Norman Visnes

EARLY in 1954, as initial development of the Galena mine was being finished, plans for stoping operations became the foremost consideration of the operating management. The Galena is being operated under lease agreement with the owner, Vulcan Silver-Lead Corp. Started in 1947, the Galena is a deep level development of American Smelting & Refining Co. and Day Mines Inc. under the management of ASARCO, in the Coeur d&apos;Alene mining district. Lead mineralization was found on the 3000 level in 1950. In 1953 development on the 3000 level disclosed a siderite vein, later known as the Silver vein, which contains commercial quantities of silver in Tetrahedrite. This vein was explored on the 2800 and 2400 levels and later on the 3400 level, the lowest in the mine. Work above the 2400 level to date has indicated that the vein dissipates to weak mineralization, and ore values are uncertain above the 2200 horizon.

Jan 1, 1957

By Ben B. Cox

Oil produced in Iraq for export during 1938 was 31,354,090 bbl., or a daily average of 85,901 bbl; This is an increase of 182,614 bbl., or 0.5 per cent over 1937. All oil exported was produced from the Kirkuk field. The Khanaqin Oil Company, Ltd., a subsidiary of the Anglo-Iranian Oil Company, Ltd., continued to supply local market requirements from its Naft Khaneh field in the Transferred Territories. Slightly more than 32,000,000 bbl. was produced in Iraq, a small part of which was used in field operations. During the year 12 wells were completed and 9 wells were drilling at the end of the year. Of the completions, 5 were producers and 1 was an oil-water level observation well in proved fields, and 6 were listed as failures. Basrah Concession The outstanding event of the year was the granting, by the Kingdom of Iraq, of a 75-year concession embracing approximately 89,000 sq. miles to the Basrah Petroleum Company, Ltd., a British company with French and American participation. The concession covers all parts of the Kingdom, its territorial waters, islands, submerged lands, and its interest in the Neutral Zone separating Iraq and Saudi Arabia that

Jan 1, 1939

By Ben B. Cox

Oil produced in Iraq for export during 1938 was 31,354,090 bbl., or a daily average of 85,901 bbl; This is an increase of 182,614 bbl., or 0.5 per cent over 1937. All oil exported was produced from the Kirkuk field. The Khanaqin Oil Company, Ltd., a subsidiary of the Anglo-Iranian Oil Company, Ltd., continued to supply local market requirements from its Naft Khaneh field in the Transferred Territories. Slightly more than 32,000,000 bbl. was produced in Iraq, a small part of which was used in field operations. During the year 12 wells were completed and 9 wells were drilling at the end of the year. Of the completions, 5 were producers and 1 was an oil-water level observation well in proved fields, and 6 were listed as failures. Basrah Concession The outstanding event of the year was the granting, by the Kingdom of Iraq, of a 75-year concession embracing approximately 89,000 sq. miles to the Basrah Petroleum Company, Ltd., a British company with French and American participation. The concession covers all parts of the Kingdom, its territorial waters, islands, submerged lands, and its interest in the Neutral Zone separating Iraq and Saudi Arabia that

Jan 1, 1939

By John V. Beall

Thai means free. Historically accurate, as the country has never been subjugated by foreign occupation, the name "The Land of the Free" also seems to fit the attitude of the people. At the Bangkok airport, without so much as a kopkhun (thank you), travelers are found behind, beside and in front of ticket counters. A pretty Thai face on TV calls flights in English and Thai. Baggage disappears with alarming rapidity and your reporter and spouse despaired of ever being reunited with it. But at the entrance, all the parts came together and there was even a limousine from our hotel, The Oriental. Driving downtown English style, we noted that there were four lanes of traffic occupying the space we would allow for three lanes. Motorcycles and enclosed three-wheel motorcycle taxis were much in evidence, but the occasional water buffalo held up the slow lane. In the city, men wore European-type slacks and shirts but the women were colorful in traditional ankle-length wraparound skirts.

Jan 1, 1970

By B. M. Andreas

PRIOR to 1934 all haulage of ore and stripping on the Mesabi Range was by rail. Early rail systems had small narrow-gage locomotives with correspondingly small dump cars. These trains were replaced with larger standard gage rail systems powered by steam locomotives ranging up to 224 tons in weight, which have in turn been replaced by diesel electric locomotives. Along with this development cars have been increased to 30-cu yd capacity. Improvement of cars includes alloy steel construction for lower over-all weight and use of roller bearings to decrease rolling resistance. Despite all of these developments, the total material hauled by rail on the Mesabi Range has decreased every year. Yet, this is no reason to believe that rail haulage is becoming obsolete. Its adaptation to small mine operation has become impractical, but in large mines where normal railroad grades are possible or where hauls to plants or dumps are long, rail haulage is still one of the most economical methods of transporting large quantities of material.

Jan 1, 1954

By Michel L. Bilodeau

The objective of delineation drilling is to provide a data base for the tonnage and grade estimates required to evaluate the economics of mine development. As drilling information is accumulated, geological risk is reduced and more reliable estimates of tonnage and grade are obtained. Investment in drilling is justified by the benefits which result from improving the reliability of the economic criteria evaluated. These benefits are subject to diminishing returns, i.e. as drilling information is accumulated the reliability of the economic criteria evaluated is improved but at a decreasing rate. At the same time, costs are incurred -- the direct investment cost associated with additional drilling and the time cost of delaying possible production revenues. The economic sampling limit is de- fined by the point at which the marginal benefits from drilling investment just balance the marginal costs. The paper describes the formulation of an economic model to optimize investment in delineation drilling. The model is applied to a simulated mineral deposit to illustrate the economic effects of a sequential drilling program.

Jan 1, 1977