Search Documents

By J. E. Gruzleski, O. Knacke, M. J. Meixner

The evolution of CO from small specimens of solidifying steel was investigated using a thermobalance technique. Gas evolution begins in the temperature range between 1400" to .1450°C. This behavior is independent of the initial carbon content and the cooling rate. At a constant temperature above 1220°C, the rate of gas evolution is temperature independent. Out-gassing of the specimen is thought to proceed through small channels formed by the coalescence of bubbles between dendrites. LIQUID metals have a higher solubility for gas than the solid. During freezing, these gases form bubbles which may either escape or remain trapped in the solid. Recent work1 on the evolution of oxygen from solidifying silver showed that the gas is not liberated until a large fraction of the melt has solidified, and that the gas is evolved in an almost explosive manner. Because of the commercial importance of CO evolution in solidifying steel, a similar investigation was undertaken to study the mechanism of gas liberation in steel. EXPERIMENTAL The thermogravimetric method of Knacke and eixner1 to follow gas evolution by weight changes was employed. Weight differences of 0.1 mg could be reproducibly measured on specimens weighing 2.5 g. These specimens were taken from alloys with varying carbon contents from <0.01 to 0.11 wt pct and <0.01 wt pct of each of silicon, manganese, and aluminum. Specimens contained in 8 mm ID magnesium alumi-nate crucibles were heated to 1550°C under 1 atm of very pure (99.995 pct) CO with a tungsten resistance furnace. The specimen temperature was measured with a Pt-Pt/Rh thermocouple located directly beside the crucible. It is felt that the temperature thus measured was within 5" to 10°C of the specimen temperature since on fusion the weight of the specimen increased due to uptake of CO, and this weight increase was always observed to begin within the temperature range of 1530" to 1540°C. Even after 3 hr there was a small weight increase with time indicating that the molten specimen was not completely saturated with CO. Therefore, complete saturation was not attempted, and all specimens were simply held for 3 hr at 1550°C before cooling. Two types of cooling experiments were performed. One consisted of continuous cooling at linear rates from 5°C to 20°C per min down to 1020°C. The second type of experiment involved continuous cooling at 10°C per min to a predetermined temperature, and then holding the specimen at this temperature for a certain time. During all of these experiments, the sample weight was recorded as a function of time and temperature. OBSERVATIONS Continuous Cooling Experiments. No gas evolution was detected above 1450°C. The initial weight decrease always occurred between 1400" and 1450°C with the average at 1430°C. With further cooling, gas evolution continued to about 1150°C. Between this temperature and 1020°C no further outgassing was observed. This behavior did not seem to depend on the initial carbon content nor on the cooling rate in the range investigated. Typical patterns of gas evolution are shown in Figs. 1 and 2 for different initial carbon levels and cooling rates. The total amount of gas liberated during solidification varied with the rate of cooling. The total weight change on continuous cooling at a rate of 10°C per min

Jan 1, 1970

By M. E. Wadsworth, I. B. Cutler

Coprecipitation of anionic and cationic polyelectrolytes has been applied to floccula-tion of several mineral systems. Results obtained in a study of the flocculation of kaolinite and hematite suspensions of polycationic and polyanionic electrolytes are presented. Greatly increased settling rates were observed following precipitation of positive and negative polyelectrolytes on the surface of finely divided minerals in aqueous suspension. The ratios of polycationic to polyanionic electrolytes required to produce maximum sedimentation have been shown to correspond closely with the equivalence points obtained by light scattering studies of systems containing the positive and negative polyelectrolytes by themselves. DISPERSION of colloids has been of interest to surface chemists for many years. Flocculation studies have been employed to evaluate the limits of colloid stability. In water suspensions, colloids become unstable and flocculate when the ( potential, the potential of the kinetic solvation sheath, falls to a value at which van der Waals forces may act to draw the particles together. This may happen through an adjustment of the pH of the suspension or by addition of a salt. Optimum conditions for rapid formation of large flocs are found in the region of minimum ( potential. In addition to these well known considerations, colloids in water suspensions are known to be flocculated by certain large organic macromolecules. These polyelectrolytes in some cases minimize the i potential and in other instances increase the attractive forces by supplying sites for hydrogen bonding.&apos; Use of organic polyelectrolytes in flocculation of mineral colloids has increased rapidly in recent years. These materials are now recognized as indispensable aids to fluid-solid separations in many extractive metallurgical operations. They have been found to increase both the settling rate in thickeners and the filtration rate of filters. In the elucidation of the characteristics of these organic reagents as floc-culants in this laboratory, it was discovered that interaction of certain polyelectrolytes had a surprisingly good effect on flocculation of mineral colloids. Experimental Procedure: The anionic flocculants used in this study were Lytron 886 and 887, produced by Monsanto Chemical Co. Both reagents are copolymers of vinyl acetate and maleic anhydride. Lime is added to Lytron 886, whereas Lytron 887 is all organic. These reagents possess two carboxyl groups for each acetate group and are therefore anionic in character. The cationic reagents used were the Peter Cooper Co. 1-X and 2-X glues. The structures are not definitely known, but the re- agents are amines and are cationic in character. The glues were prepared in the chrome-alum form. Both types of reagents may be classified as polyelectrolytes in that they are high molecular weight polymers and ionize in water. All data presented are in terms of sedimentation rate, measured in 250-ml glass-stoppered graduated cylinders. With suitable precautions such measurements are fairly reproducible and provide a sensitive means for selecting important parameters such as pH, reagent concentration, and floc size and density.2 Agitation was standardized with five complete end over end cycles of the suspensions in the stoppered graduated cylinders.

Jan 1, 1957

By R. M. Scafe

Although hydrogen has been intensively studied in its relation to steel quality, the methods of sampling and determinations are still open to question. It is true that various procedures have been proposed but actually there has not been sufficient agreement to establish a common base from which to work. As a result, it is difficult, to say the least, to correlate the reported results of some of the investigators in this field. The present symposium, premised on methods rather than effects, should prove of considerable value. For the purpose of this discussion two methods of sampling and analysis will be considered. First, sampling of molten steel in the ingot mold by use of an evacuated tube and cylinder using conventional methods of analysis for the gases collected; second, analysis by vacuum extraction involving the use of heating equipment and the determination of the amount of hydrogen evolved from solid steel samples by measurement at reduced pressures. Both methods have been used at Duquesne Steel Works and it is believed that either may be used with considerable benefit if the limitations of each method are recognized. Evacuated Tube and Cylinder Sampling devices for gases in molten steel suggested by various investigators range from very cumbersome and complicated devices to the relatively simple evacuated tube and cylinder used by Soler for deter- mining the CO content of the bath. This latter device was adopted (Fig. I) and modified to meet conditions at Duquesne Works. The principal modifications were in placing the cylinder at the side of the tube and the use of a sleeve on the immersion end of the tube. The first modification was made so that the cylinder could be readily detached and taken to the laboratory; the second, because of the difficulty encountered in obtaining an airtight seal after sampling and because of our practice of re-using the tube. Rigid control of the method of sampling and of the handling of the sample according to plan are of primary importance in hydrogen determinations. This applies to both the sampling of molten steel and the determination of the hydrogen content of cold steel samples. Except for a few preliminary samples taken from spoons, all work on molten steels using the evacuated tube was confined to the sampling and analysis of molten steel during the pour. As mentioned, uniformity of sampling was a basic consideration. As a result, every effort was made to follow definite sampling techniques and procedures. These included control of the depth below the surface from which the sample was taken, the timing between the shutoff and taking of the sample, as well as maintenance and care of the equipment. The distance below the surface at which the sample was taken was readily controlled bv means of a crosspiece and centering device attached to the tube. The steel was poured into the mold to the hot-top junction, the tube was then lowered into the 75

Jan 1, 1945

A cooperative service for engineers and their employers under the direction of the American Institute of Mining and Metallurgical Engineers; American Society of Civil Engineers; American Society of Mechanical Engineers; and American Institute of Electrical Engineers, and with the cooperation in Chicago of the Western Society of Engineers, and in San Francisco of the California Section of the American Chemical Society and the Engineers Club of San Francisco. For information as to men available or positions open, address the nearest office.

Jan 1, 1923

ASSOCIATED MINERS, UNIVERSITY OF IDAHO The following officers of the Associated Miners of the University of Idaho have been elected for the academic year for 1918-1919: President, Lloyd A. McDougal; vice-president, Russel D. Bowers; secretary-treasurer, Charles M. Otter. While the society has been somewhat quiescent during the existence of the S. A. T. C., we are now looking forward to an active session with the resumption of normal university life. CHARLES M. OTTER, Sec&apos;y-Treas.

Jan 2, 1919

At its meeting on February 21, 1933, the Board of Directors the following resolution defining and expressing the policy of the Institute with respect to official participation or action in controversial matters: WHEREAS, the Board of Directors at its last meting passed the following resolution: "The Board of Directors, having been appealed to by several Local Sections for advice concerning the attitude and policy of the Institute relating to the endorsement of candidates for public office, the following statement of policy is formulated:

Jan 1, 1939

At its meeting on February 21, 1933, the Board of Directors the following resolution defining and expressing the policy of the Institute with respect to official participation or action in controversial matters: WHEREAS, the Board of Directors at its last meting passed the following resolution: "The Board of Directors, having been appealed to by several Local Sections for advice concerning the attitude and policy of the Institute relating to the endorsement of candidates for public office, the following statement of policy is formulated:

Jan 1, 1941

By John Randall

IT is a fair assumption that the main purpose of any diagram is to present facts to the eye in more convenient form than they could be tabulated in figures, and this implies that a screen diagram should set forth in a convenient and familiar form certain facts as to the character of the material screened regardless. of the screen standards used, and it seems particularly desirable on account of the well-known differences in the size of openings of different laboratory screens having the same nominal mesh. In making screen-sizing tests it has been customary to first consider the largest size, going progressively to the smallest, and this seems to have led to the practice of placing the smallest size at the right-hand side of the diagram and .measuring toward the left. This is not altogether convenient and might he changed to advantage, but for illustration I have preserved that feature and present the method just as I have used it for over 2 years. Direct plotting in which the intervals on the diagram are proportional to the sizes of the openings, or to the arithmetical difference between them, seems at first sight more natural and is extremely useful for certain purposes, but it makes the diagram very crowded in the smaller screen sizes while the larger ones occupy unnecessary space, snaking it less convenient for most purposes, and for that reason the method here discussed is the well-known one based oil the ratio between openings, and is plotted in logarithms instead of the direct values of the screen opening. Metric coordinate paper is convenient, although .not necessary; it is recommended, as the use of the metric scale gives a diagram of convenient size, but any scale of equal. parts may be used. In order to make any screen diagram translatable in terms of any standard screen size, it is necessary to have rioted on the size scale of the diagram all points corresponding to the openings of the various screens in question, instead of a single series &apos;of points as with a single screen. In drawing the diagram assume 0.001 in. (corresponding approximately to 0.025 mm.) to be the smallest size to be considered and fix this as the zero point at the lower right-hand corner of the diagram. This value is selected because the values are to be plotted in logarithms, and the logarithm of 1 is zero. Then lay off to the left for the position of each screen

Jan 9, 1917

By Hermann Wedding

I ASK your permission to speak about a matter which is not of a specifically scientific nature, but more of a general-I might even say of an international-nature, and the international character which this city now presents must be my justification for introducing it. The Germans, very often, are thought to be an exceedingly warlike people, but I come to-day in the capacity of a peacemaker. Our German language is an original language; it is, therefore, a language in which it is impossible to change the meaning of a word at will. It may be, perhaps, easier in a combined language, as the English, to associate and to exchange meanings. Now, a word which we hear a great deal at the present day, is "Stahl," in English, "steel." This word means, in the German language, a substance which can be hardened. As the German literature, in relation to metallurgy, is the oldest of the modern world, this circumstance may give the German a right to ask for consideration. But I think, now, when the four languages, German, Swedish, French, and English, compete in rich metallurgical literature, it is very necessary to have uniformity in the nomenclature of iron, which would prove not only useful for science, but equally so for trade. For that purpose I propose to make the divisions of iron so that the word steel shall comprise a subdivision and not a primary division as formerly. Nature furnishes us iron mostly in the state of oxides, and if in any other condition, we must convert the ore into oxide before we can make iron. The oxides are always mixed with certain earthy substances called rock or gangue. The extraction of iron involves, therefore, the twofold process of the reduction of the iron, and im¬parting to it the amount of carbon necessary for technical purposes, and the separation of the reduced and carburized iron from the gangue. The reduction is always effected by carbon or carbonaceous substances (coke, anthracite, carbonic oxide, etc.), and the result is, according to the degree of heat employed, either malleable iron or a non-malleable iron. The process of making malleable iron in this way is called, generally, the direct process-in German, Rennarbeil. It produces the iron in a solid state with a fluid cinder. By this process our ancestors made all their iron, and it has been revived in various ways in modern times up to the process of Mr. Blair, so far as I know, always without commercial success. The

Jan 1, 1877

By Hermann Wedding

I ask your permission to speak about a matter which is not of a specifically scientific nature, but more of a general—I might even say of an international—nature, and the international character which this city now presents must be my justification for introducing it. The Germans, very often, are thought to be an exceedingly warlike people, but I come to-day in the capacity of a peacemaker. Our German language is an original language; it is, therefore, a language in which it is impossible to change the meaning of a word at will. It may be, perhaps, easier in a combined language, as the English, to associate and to exchange meanings. Now, a word which we hear a great deal at the present day, is "Stahl," in English, "steel." This word means, in the German language, a substance which can be hardened. As the German literature, in relation to metallurgy, is the oldest of the modern world, this circumstance may give the German a right to ask for consideration. But I think, now, when the four languages, German, Swedish, French, and English, compete in rich metallurgical literature, it is very necessary to have uniformity in the nomenclature of iron, which would prove not only useful for science, but equally so for trade. For that purpose I propose to make the divisions of iron so that the word steel shall comprise a subdivision and not a primary division as formerly. Nature furnishes us iron mostly in the state of oxides, and if in any other condition, we must convert the ore into oxide before we can make iron. The oxides are always mixed with certain earthy substances called rock or gangue. The extraction of iron involves, therefore, the twofold process of the reduction of the iron, and imparting to it the amount of carbon necessary for technical purposes, and the separation of the reduced and carburized iron from the gangue. The reduction is always effected by carbon or carbonaceous substances (coke, anthracite, carbonic oxide, etc.), and the result is, according to the degree of heat employed, either malleable iron or a non-malleable iron. The process of malting malleable iron in this way is called, generally, the direct process—in German, Rennarbeit. It produces the iron in a solid state with a fluid cinder. By this process our ancestors made all their iron, and it has been revived in various ways in modern times up to the process of Mr. Blair, so far as I know, always without commercial success. The

By J. A. Holmes

As the Appalachian mountains reach their maximum development in western North Carolina, we find also in that region indications of extensive dynamic disturbances and alterations undergone by the rocks in&apos; connection with these mountain uplifts. Among the minor results of these changes have been the formation of numerous dikes or a veins " of exceedingly coarse granitic materials, which in some places are mined for the mica which they contain, and in other places are quarried for kaolin. These dikes are filled with quartz, feldspar, and mica, in varying proportions, very coarsely crystallized. Sometimes the mica (generally muscovite), sometimes the feldspar (generally albite or orthoclase) predominates. When the mica is present in considerable quantity, and in large crystals, the dike is usually spoken of as a mica-vein, and is often worked for mica. Sometimes these crystals of mica occur on one side or the other; sometimes on both sides; and sometimes they are largely concentrated toward the middle of the vein, or, it may be, distributed throughout the dike with a considerable degree of uniformity. In many cases the crystals of mica are too small and few to permit the working of the vein as a micamine ; in other cases, very little mica is present, and the feldspar constitutes the larger part of the material. This feldspar of the dikes undergoes, through the weathering action of the atmosphere, certain chemical changes, resulting in its alteration from feldspar into kaolinite—the kaolin of commerce. These dikes vary considerably in size, ranging from a few inches to several hundred feet in thickness, and up to many hundred yards in length. They are generally parallel to the schistosity of the crystalline rocks, which, however, in some cases, they cross at varying angles. The kaolin in those dikes which occur in the Unaka or

Jan 1, 1896

JAMES E. HOWARD,* Washington, D. C. (written discussion?). -Mr. Comstock, in his classification of the possible causes of transverse fissures, has not quite caught the point of view of the writer. It appears, following the trend of thought in Mr. Comstock&apos;s paper, that three groups instead of two might bee enumerated, namely: Fatigue of the steel, quality or, preferably, grade of steel, and mill practice. All steels are liable to failure by fatigue. Stresses that are capable of causing fatigue fractures are modified in their magnitude by the grade of steel acted upon. Mill practice is a term having a very wide meaning and in its relations to the development of transverse fissures has been used with such vagueness as to include many known factors and some that are unknown in the arts. According to the grade of steel employed, fatigue fractures may be accomplished by loads of greater or less magnitude, hence there is a relation between quality, or grade, of steel and the display of fatigue fractures. Mill practice of such an order as to affect the formation of transverse fissures must be shown to exert an influence on the ability of the steel to endure repeated stresses. Different grades of steel are selected for different purposes. Steel employed for fire-box purposes is of different grade from that used for cutting tools; although each grade is suitable for its purpose, and therefore of good quality. It is conceivable that a demand might be made for steel of physical properties in excess of those of any known grade. Under such a demand, impossible of&apos; fulfillment, it would not be proper to refer to the steels as being deficient in quality; to do so would be a failure to recognize that all steels have their limitations in strength. Service conditions peculiar to rails admit of successive advance until the conditions can no longer-be met. The failure of a large number of rails from one type of failure, when all known means of averting the failure have been employed without success, is sufficient evidence that the end is close at hand. Iron rails, for a time, successfully met the requirements of railway service but weight of equipment, motive power, and rolling stock were increased, necessitating the use of steel. The early steel rails enjoyed the reputation of being of excellent quality, although: neither chemically nor structurally would they be so regarded ,lit the present time. They did good service in their day and under the conditions then prevailing were good rails. To meet the increased weight of rolling stock there has been

Jan 3, 1919

By J. W. Marx, R. H. Langenheim

The authors are to he complimented for a timely presentation of useful information concerning application of heat to oil reservoirs to increase the rate and ultimate recovery of oil. The solution for heated area resulting from constant rate injection of a hot fluid, presented by the authors, and the fluid-flow analogy, solved by Carter,&apos; are particularly interesting in that 110 restriction is placed on the direction of development of the heated area. It is not necessary that the heated area grow radially. Thus the solution could provide useful information for heat injection in any type of well pattern with any specified swept area data. However, it was assumed in the development that the heated region would remain at a constant clevatcd temperature. Vertical heat losses were computed on this basis. Physically. the assumption that the heated region will remain at a constant temperature (independent of distance from the injection point) appears to require that the heat injection medium be stcam, or other condensible gases near the boding point at injection pressure. If a hot liquid below the boiling point or a hot gas considerably above saturation temperature were used, the temperature of the heated region would decrease with distance from the injection well. Lauwerier2 has discussed this problem for a linear system. (See also Jenkins and Aronolsky; and McNiel and Nelson.&apos;) Thus, the authors&apos; solution applies more nearly to steam injection than to hot water injection or hot, non-condensable gas injection. Assuming steam as the injection medium, it appears that steam would pass through the constant-temperature heated region and condense upon contact with the unheated sand. The tempcrature in the condensing region would probably be governed by the release of heat of vaporization required for phase equilibrium at the existing pressure distribution. Temperatures in the region would also be influenced by vaporization of hydrocarbon. Thus, it is doubtful that an expression for radial temperature distribution based on heat conduction only (such as the authors&apos; Eq. 9) would have practical significance. As pointed out by Marx and Langenheim, the growth of the heated area under constant rate steam drive will eventually be limited economically by vertical heat loss. The possibility of continuing to move heat economically by cold water injection or by increasing the steam injection rate appears to be a very important consideration. (Movement of liquids away from the injection well should increase injectivity.) Fortunately, the solution presented by the authors may be generalized to thc case of a variable heat injection rate. The general solution is:

By Samuel H. Dolbear

THE purpose of a technical report is to record facts, usually collected by investigation, and to interpret these facts in understandable language. The audience may range from a small shareholder without technical knowledge, to a highly trained engineer or geologist. If the client is a mining company with technically trained executives, the report writer&apos;s problem is relatively simple. The writer will then be appraised not only for his conclusions, but for clarity of language and organization of the report. If the writing is bad, the construction careless, and there is a failure to clearly convey to the reader the facts and the author&apos;s conclusions, the report is a failure and the writer may have damaged his professional character. Spoken words die quickly, written words may constitute a permanent record and if they are badly composed they may rise up to damn the author. "A good measure of an author&apos;s understanding of his subject is his ability to express it clearly in plain words." Good English Teachers in the fields of mineral technology have frequently complained that even in post-graduate groups there is an appalling indifference to their appeals for good English. Some have even noted a student&apos;s belief that the use of refined English is effeminate. If those with such immature beliefs could measure the pay-check damage arising from the use of "sloppy" language, they would realize that precision and refinement in English may be quite as important as technical accuracy. When the reader audience is without technical knowledge simplicity in treatment becomes especially important. If one is engaged in consulting work, in government service, or in any field where reports have public distribution, the language employed should be technically adequate but simple enough to be understood by non-technical readers. For example, one may use the term "visual" in place of "megascopic." Technical language can be so obscure that it cannot be understood even by highly-trained students. In the March-April (Vol. 47-No. 2) issue of Economic Geology, Nicholas Vanserg ridicules these extremes and quotes various paragraphs from published material, such for example: "However, lattice orientation unaccompanied by cognate dimensional orientation can never be attributable to growth from an isotropic blastetrix." "The temperature declines because of cessation of the exothermic chemical and mechanical equilibriopetal processes." These he calls "good geologese" and they are calculated not only to baffle the reader but to impress upon him the erudite character of the author. Revision In some cases, difficulty arises from the fact that the writer is too close to the subject and unconsciously assumes that his reader is equally familiar with the background of the report. It is difficult for the writer to regard his work objectively and to determine to what extent it is likely to be understood. Every important manuscript will gain in clarity if the author will have it reviewed by an informed reader. But the writer must not be oversensitive to criticism and should not treat his composition as perfect and beyond the possibility of improvement. The first draft of a report always requires revision, regardless of the care used or the ability of the writer. Three or four revisions are not uncommon. The first draft usually requires expansion in places, the deletion of non-essential material, and language changes to promote clarity of expression. This should be done by the author after a lapse of time, even if only overnight, in which his mind has been occupied on some other subject. Possible improvements are always more visible. The manuscript should be passed on to another reader for further suggestions. Organization of Material The engineer should study available reports and library references before going into the field. If the previous reports have been responsibly done and can be accepted as correct, then much field time can be saved. It is, of course, customary to make some on-the-ground checks to confirm earlier reports, particularly those relating to ore reserve which may have undergone changes. Report writing requires time and expense, but nevertheless, the basic reasons for conclusions should be presented even in the case of a worthless property, for it may prevent a duplication of the work. If the mine examined is obviously of no further interest, no useful purpose can be, served by preparing a report in detail. In one case an engineer travelled all the way to South America only to find that the mine had been grossly misrepresented and was valueless. His cabled report "Nonsense" is a case of over-simplification, but it served his company&apos;s purpose. The first step in report organization should be the selection of subjects. This should be done at the mine, and the data collected for each subject should be reviewed in considerable detail on the ground. Otherwise one may find that he has failed to collect some essential details not readily obtained after he has returned to headquarters. If the property to be described is undeveloped, then many of the subject titles are automatically eliminated. Usually no useful purpose is served by an attempt to calculate the cost of production under such circumstances, although the cost of exploration

Jan 1, 1952

By A. S. Malicsi, I. Iwasaki

The removal of hydrophobic coatings of flotation collectors from iron ores becomes of interest when a duplex flotation process is considered for upgrading, when a pelletizing process is considered for a concentrate floated with a fatty acid or a soap collector, or when a disposal of froth products from cationic silica flotation is of environmental concern. Ozone can oxidize organic compounds rapidly, thereby removing the hydrophobic coatings of flotation collectors. Ozone is widely used for treating and purifying drinking water, waste water treatment, and for chemicals processing (Murphy and Orr, 1975; Rice et al., 1980). Its uses in metallurgical operations, however, are very sparse (Allegrini et al., 1970; Chernobrov and Rozinoyer, 1975; Ishii et al., 1970; Iwasaki and Malicsi, 1985; Matsubara et al., 1978). Yet, its high reactivity and the absence of potentially hazardous byproducts become of interest in destroying flotation reagents adsorbed on mineral surfaces or remaining in mill water for recycle or for discharge. Duplex Flotation A duplex flotation process, as applied to oxidized iron ores, would involve a fatty acid flotation of iron minerals followed by an amine flotation of the siliceous gangue from the rougher iron concentrate. Such a process has been used in the Florida phosphate fields. Fatty acid coatings cannot be removed as readily with a simple acid or alkali treatment from iron oxide surfaces as from Florida phosphates. A combination of reagents, such as lime and quebracho, lime and alkali phosphate, or sulfuric acid and oxalic acid, has therefore been proposed. In a previous article (Iwasaki et al., 1967) , the use of activated carbon was found to be effective in removing fatty acid coatings both in the duplex flotation and the pelletizing processes. The use of ozone offers another approach to the removal of fatty acid coatings from iron oxide surfaces. To investigate the possible application of the duplex flotation process, a specularite ore from Michigan analyzing 36.5% iron was used. A 600-g (1.3-1b) sample was ground in a laboratory rod mill together with 250 g/t (0.5 lb per st) of sodium silicate to -150 µm (-100 mesh). This was transferred to a Fagergren laboratory flotation cell, and deslimed four times at 20 µm (quartz equivalent). The deslimed pulp was transferred to a laboratory conditioner, diluted to 40% solids, and conditioned with 250 g/t (0.5 lb per st) of soda ash and 250 g/t (0.5 lb per st) of oleic acid. The conditioned pulp was then transferred back to the Fagergren cell, floated until barren of froth, and the rougher froth product was returned to the cell and cleaned. The results are presented in Table 1. The cleaner concentrate at this point analyzed 45.3% Fe. The cleaner concentrate coated with fatty acid was transferred to a 2-L (0.53-gal) beaker. While the pulp was agitated with a glass T-stirrer, ozone was bubbled into the agitated pulp for 15 minutes at a rate of 10 mg/min (0.00035 oz per min) ozone (250 g/t or 0.5 lb per st 03 feed). It was observed that the pulp ceased to froth after about 10 minutes. The amine flotation of siliceous gangue from the ozonated pulp was carried out first by conditioning with a dextrin, a commonly used starch depressant for iron oxides. This was followed by flotation with a stage addition of an ether amine at increments of 100 g/t (0.2 lb per st). Three stages were required to float the siliceous gangue to near completion. The three froth products were combined and cleaned twice. When the cationic flotation Rougher, Cleaner 1 and Cleaner 2 cell products were combined, an iron concentrate analyzing 64.5% iron was obtained at an overall iron recovery of 72.8%. Pelletizing Fatty acid flotation concentrates have been pelletized successfully in northern Michigan mills. But at other locations, fatty acid coatings on iron flotation concentrates proved so undesirable in agglomeration that other methods of concentration had to be sought. For example, a sinter mix containing iron ore concentrates upgraded by fatty acid flotation resulted in decreased productivity. This occurred because the micropellets of particles with the hydrophobic coating are less tolerant of moisture. Thus, the bed permeability is lost (Beebe, 1965). The agglomeration of concentrates obtained by the fatty acid flotation alone, and the hydrophobic coatings destroyed by ozonation or by the duplex flotation process, is not expected to cause any difficulty since the surfaces of the concentrates would be hydrophilic. Removal of the fatty acid coating with activated carbon, indicated by the loss of floatability, was shown to restore the decrepitation temperature of wet balls during drying cycle (Iwasaki et al., 1967). Disposal of Cationic Silica Flotation Froths Recent demands of iron blast furnaces place the silica content of the magnetic taconite pellets at about 5%. Conventional process for magnetic taconite involving fine grinding and magnetic separation often produces magnetic concentrates analyzing in excess of 5% silica. This is due to the presence of the middling grains of siliceous gangue and magnetite. Cationic silica flotation of magnetic taconite concentrates (DeVaney, 1949) may be used to reduce the silica content. But the amine coating on siliceous gangue becomes of environmental concern when the flotation tailings are discarded in tailing ponds.

Jan 1, 1986

By G. L. Chierici

Starting from Muskat&apos;s theory of water and gas coning, maximum permissible oil production rates without water and/or free-gas production have been determined, in a broad range of reservoir and well parameters, using the potentiometric model technique. The main assumptions made are as follows: (1) the reservoir rock is homogeneeous (either isotropic or anisotropic); (2) the volume of the aquifer underlying the oil zone is very small, so that it does not contribute to reservoir energy; and (3) the gas cap expands at a very low rate, so that it can be assumed to be in quasi-static conditions. The results obtained are presented in the form of diagrams which can be used for solving two types of problems: (1) given the reservoir and fluids characteristics, as well as the position and length of the perforated interval, determine the maximum oil production rate without water and/or free-gas production; and (2) given the reservoir and fluids characteristics only, determine the position and length of the perforated interval which optimize the maximum permissible oil production rate, without water and/or free-gas production. INTRODUCTION In oil reservoirs where the oil-bearing formation is underlain by an aquifer which does not participate in the production mechanism, water-coning is a limiting factor to the flow rates of producing wells. Production rates are usually kept to a value that will prevent the water from entering the wells. The entry of water into a well lowers its productivity by increasing the weigbt of the fluid column; moreover, the separation of water from the effluent, at the surface, may constitute a very difficult problem in cases of heavy viscous oils. A similar situation is encountered in oil reservoirs with a gas cap overlying the oil-saturated zone; here a downward gas cone is induced by the flow of oil towards the producing wells. Production rates must be low enough to prevent the gas from being produced; producing gas from the gas cap would be a waste of energy. Of course, water-coning and gas-coning phenomena can occur at the same time in the same reservoir if the oil-producing formation is both overlain by a gas zone and underlain by a water zone. Due to its relevant practical importance, the mechanism of coning was studied by many people.2,3,5-8 Defining the conditions for getting the maximum water-free and/or gas-free oil production rate is a difficult problem, often encountered under one of the following aspects: 1. Predict the maximum flow rate that can be assigned to a completed well without the simultaneous production of water and/or free-gas. 2. Define the optimum length and position of the interval to be perforated in a well, in order to obtain the maximum water and gas-free production rate. A systematic study of these problems was made by means of the electrical analog technique. The results of this study are presented here, under the form of a set of curves providing solutions for the above stated problems. These curves are valid only for homogeneous forrnations, either isotropic or anisotropic. Should the formation be non-homogeneous (by horizontal or vertical variation of permeability, shale diaphragms, fractures, etc.), a specific potentiometric study would be required for each specific case. Especially when shale diaphragms of some radial extension are present, the critical rates observed are much larger than would be expected from the diagrams. STATEMENT OF THE PROBLEM In the present study the aquifer is supposed to be of such limited volume that it does not contribute to the energy of the reservoir. Moreover, the gas cap is supposed to expand at such a low rate that the potential gradient in the gas cap is negligible. Under static conditions water-oil and gas-oil interfaces (T1 and T2) are both horizontal. When the reservoir production starts, below each well these interfaces take a cone-like shape (Fig. 1) having as an axis the axis of the well. This shape results from the equilibrium between potential gradients in the oil zone and gravitational forces due to density differences between oil and water and between oil and gas. Assuming the oil-bearing formation to be homogeneous and the oil to be incompressible, the analysis of the problem (see Appendix) shows that the oil-water and gas-oil interfaces are stable only if the oil production rate of the well is not higher than the following values.

Jan 1, 1965

By S. R. Bardsley, S. T. Algermissen

Induction, nuclear and sonic well-logging methods were employed in a Green River formation oil-shale analysis and evaluation study conducted in northeastern Uintah County, Utah. The physical and chemical properties of an oil-shale section, previously cored and assayed by conventional methods, were used to evaluate the response of the various logs. The logging program was designed to measure variable properties of oil shale which relate to oil-yield potential in order that a relationship between assay-oil yield and log-determined properties could be identified, thereby permitting a direct determination of yield potential from logs alone. All of the major oil-shale zones and section ttlarkers are recognizable on the logs used in the study. The relationship between the response of the Density and Sonic logs and the assay-oil yield in gallons per ton was suficient to perinit the derivation of equations expressing the relationships. These equations can be used to determine the potential oil yield in gallons per ton of an oil-shale zone or section. The Neutron log response distinguishes the rich oil-shale intervals from the lean intervals, but does not appear to permit establishment of a quantitative relationship. The Garnma-Ray and Induction logs indicate only a qualitative relationship to oil-shale yields. Logging oil shale by Gamma-Gamrna Density and/ or Sonic logging methods will permit a fast, economical and accurate means of evaluating the potential yield of oil-shale deposits. Considerable sums of money have been allocated to Green River formation oil-shale evaluation during the past years by both private enterprise and Federal and state governments. The result of the work accomplished to date is commendable, but the task of fully exploring and evaluating one of the world&apos;s greatest reserves of potential energy for economical exploitation is enormous and much information is still needed. Present methods of evaluation consist primarily of sampling and assaying the oil shale for potential yield. The data received are excellent, but are both costly (inasmuch as it requires funds specifically allocated for the evaluation purpose) and time-consuming (as each representative sample must be assayed in the laboratory by specially trained personnel). At the present time, the Green River formation oil-shale province is one of the most active areas in the Rocky Mountain region for exploratory oil and gas drilling. This activity could play a twofold role and serve the function of spear-heading many oil-shale evaluation programs, as it could provide both cutting samples for assaying, geophysical data and modern well logs. This paper deals with a recent study conducted on Green River formation oil shale in which the application of induction, sonic and nuclear well logs to oil-shale evaluation was tested and proved. THEORY AND DEFINITIONS Oil shale may be described as siliceous marlstone, rich in solid organic matter called "kerogen". Kerogen is only slightly soluble in organic solvents, but it will decompose and yield oil vapors and gas when heated to destructive distillation temperatures at about 800 F. The mineral constituents of Green River formation oil shale are found in essentially uniform proportions with one another. The dominant types are, in the general order of abundance, dolomite, calcite, feldspars and quartz. Kerogen is also essentially uniform in its composition, and is about 80 per cent carbon and 10 per cent hydrogen by weight. The ratio of kerogen to the mineral constituents determines the richness or potential yield of the oil shale. This ratio also determines the total physical and chemical properties of the rock and provides a basis by which oil-shale richness may be determined from well logs. Because Green River formation oil shale was deposited in a lacustrine environment, the lithology is laterally consistent over wide areas. The vertical section consists predominantly of thin bands of alternating rich and lean oil shale which have been described by Bradley&apos; as varves. The varves are occasionally broken by thin bands of volcanic ash and tuff and by zones of lean vugular oil shale. The effect that the thin non-oil shale beds and vugular zones would have on the well log analysis was a prime concern in the study. To cope with this possible problem, the logs used in the study were of two types: (1) logs believed to respond favorably to those properties of oil shale which are dependent upon the kero-gen-to-mineral ratio, these logs being the Gamma-Gamma Density log, the Sonic log and the Neutron log; and (2) logs that would respond to litho-logies and properties within the oil-shale section not associated with yield that might result in anomalous responses by the yield-measuring logs. Logs of the second type were the Gamma-Kay log, the Induction log and the Caliper log. THE PRESENT STUDY The present logging study was con-

At its meeting on February 21, 1933, the Board of Directors passed the following resolution defining and expressing the policy of the Institute with respect to official participation or action in controversial matters: WHEREAS, the Board of Directors at its last meeting passed the following resolution : "The Board of Directors, having been appealed to by several Local Sections for advice concerning the attitude and policy of the Institute relating to the endorsement of candidates for public office, the following statement of policy is formulated;

Jan 1, 1934

By Richard Conkling

A SHALE layer, buried beneath two or three thousand feet of strata, in some instances, will upon folding become thicker in the synclines and thinner on top of the anticlines. This can be accounted for, in part, by the stretching on the crests of the fold and the compressing in the troughs; but this will by no, means account for all of it, as is shown in the example herein set forth. It is my firm belief that the rest of the thickness is due to flow. What causes the movement, however, does not concern us here, so long as there is movement, for this article purposes to show its effect upon the producing area of different sands. It is the author&apos;s hope, in this way, to drop a hint or two that may be valuable to the oil geologist, in making estimates of future productions and values of oil properties. An example will be given from property in the famous Cushing Pool in northeastern Oklahoma, where the author has had occasion to make a detailed study before recommending some property to his company, and has then been able to watch the results of this work. The author never mapped the surface structure in this pool, as this had been done by Frank Buttram when he was with the Oklahoma Geological Survey. We are using, therefore, a section of his map in this article for our surface contours. The main east clip comes farther east than this section shows.

Jan 10, 1916

Oscar Rohn was born in Jackson, Wis., June 27, 1870. He attended the University of Wisconsin and there gained from Professor Van Hise his inspiration for scientific effort and useful attainment. While a student at Wisconsin he was interested in athletics and was a member of the first eight-oared crew that Wisconsin sent to compete with Eastern crews at Poughkeepsie. He was an instructor in the gymnasium for several years. He received his B. S. in 1895 at Wisconsin, specializing in engineering and geology. 1229

Jan 1, 1924