Search Documents

By R. J. Robbins, D. L. Anderson

A tunnel boring machine has potential use in al- most any type of mining where the access shaft (or adit) is large enough or can be made large enough for its initial entry and where the orebody is of sufficient size to warrant its use. Some time will inevitably be lost in negotiating curves or making lateral moves and moving from level to level. Nevertheless, if the orebody is sufficiently large, advance scheduling can minimize the lost time encountered in such moves. Ideally, a mine will be planned for the use of these machines, thus eliminating access and transport problems. From the viewpoint of time involved, the rate of advance by boring as compared to conventional means is worthy of review. For instance, the Blanco Tunnel, one section of the Bureau of Reclamation's San Juan-Chama Project in southern Colorado, was bored in competent sedimentary rock with the following performance:

Jan 7, 1967

By Frederick Prime

At the last meeting of the Institute, Mr. A. L. Holley read a paper on "Steel," in which he proposes for it a definition so opposed to the one generally received, as to call for some remarks. Until within the last five or six years there has been no dispute on the subject, and it seems worth while to investigate the matter. For not only does a proper tax on all importations depend on a proper appreciation of the term steel, but it is necessary to know whether steel, or wroughtiron, or homogeneous iron are requisite in all processes of manufacture in which malleable iron is employed, on accouut of cost, strength, etc. Karsten* says: "Iron may be obtained, either as an unforgeable, unweldable metal, which melts at a high heat, termed cast-iron ; or as a ductile, weldable, soft, metal, which can only be melted at the

By Robert Bell

The regions to which this paper refers include the whole of the Dominion of Canada east of the 130 Rocky Mountains and north of the water-shed of the St. Lawrence. Very little exploration for economic minerals has yet been done in this immense country; but that little has already served to indicate great wealth in some localities. Having been engaged for a number of years in conducting government geological explorations in these vast territories, I shall endeavor to give the members of the Institute an idea of the prospective mineral resources of almost half a continent, as far as they are yet discernible. I purpose confining my observations to the economic minerals, and will not attempt a description of the geology of these territories; hut it will be necessary to say a few words about the rocks in order the better to explain the distribution of such minerals. The Laurentian nucleus of the continent is the principal feature of the geological map of the Dominion. It stretches from Lake Superior to Baffin's Bay, and from Great Bear Lake to the Straits of Belle Isle. Hudson's Bay itself, which is half the size of the Mediterranean Sea of the old world, lies in the center of this area. Its shores are bordered in places with newer rocks. On the west side of James' Bay (its southern prololigation) these extend inland over 200 miles, and consist of fossiliferous Devonian and Silurian strata. On the western and northwestern side of Hudson's Bay proper, altered rocks are met with, some of which resemble the gold-bearing strata of Nora Scotia, some the Huronian of Lake Huron, some the older Huronian, and others the crystalline series of the neighborhood of Sherbrooke in the Province of Quebec. Along the east coast (called the Eastmain)and among the islands lying off it, there is an interesting set of volcanic and sedimentary rocks which appears to be identical with the Animikie and the Nipigon series of Lake Superior. The area which I have characterized in a general way as Laurentian, includes tracts and belts, more or less extensive, of the Huronian series. Such areas appear to be most common, and have been best explored, in the country between the Great Lakes and Hudson's Bay.

Jan 1, 1886

The American Steel Treaters Society, which meets at the Seventh Regiment Armory, Chicago, Ill., on Sept. 23-27, has provided an especially interesting program of thirty-five papers. They deal with "Heat Treatment of Steels for Cutting Purposes," "Heat Treatment of Miscellaneous Products," Heat Treatment of Steel for Intermittent Cutting Purposes, "Results of Investigation Pertaining to Heat Treatment," "Heat Treating Equipment," "Solution of Modern `demands on Heat Treating."

Jan 9, 1919

By Edward Hart

THE specimen of glazy iron used for analysis was highly characteristic in appearance. It was made at one of the furnaces of the Glendon Iron Works, working a light burden of ore with a highly silicious cinder. There are very few records of analyses of this variety of iron. I have been able to find but the two given by Bell, and I add these to my analysis for comparison.

Jan 1, 1877

By W. C. Knopf, I. M. LaBaron

In the Carlsbad area potash is dry-mined and wet- concentrated. Wet concentration involves recirculation of saturated brines, with resultant difficulties of brine disposal and inherent losses in recovery through solution of the KC1. A dry beneficiation process for potash minerals would offer many advantages over present methods. International Minerals & Chemical Corp. has been working on development of a dry process for some time. This article is a progress report.

Jan 10, 1958

By Robert Franke

(Butte Meeting, August, 1913.) IN view of the prominence which the conical mill has attained in the fine-crushing field .within the few years since its introduction, the following comparison with its more mature forerunner, the Chilean mill, based on extensive tests, is submitted in the interest of the milling profession. Soon after designing the concentrating plant of the Miami Copper Co. in 1909, the Hardinge conical mill made its appearance in the milling forum. . Its possibility as a suitable crushing device for the plant was well recognized, but in view of the lack of commercial demonstration, at the time, as to capacity, efficiency for desired product, and the still more uncertain factors of cost of maintenance and power consumption, it was deemed that the immediate adoption of this machine throughout the plant would be a hazardous undertaking. For these reasons it was decided to equip the majority of the immediately required units of the plant with Chilean mills, the fine-crushing proficiencies of which were better known, and one section with Hardinge mills, to serve as a test unit for the guidance of future installations and replacements. Thereby, after 1.5 years' operation with both types of mills, a thorough test as to metallurgical efficiency and cost economy has been obtained. The conical mill used in these tests is the 8-ft. Hardinge pebble mill, having a cylinder 22 in. in length. The cylindrical portion of this mill is lined with cast-iron liner plates, and the conical extensions with silex bricks bound together by cement. Each. liner plate carries a projecting lifter, the function of which is to increase the height of drop of the lifted material. Danish No. 5 pebbles, obtained from the coast deposits of Denmark, are used for the grinding charge. The Chilean mill used is a fast-running, 3-roller, 6-ft. Saturn mill, with screens of 0.037-in. opening. The feed to these mills is the oversize of Callow screens having 0.029-in. openings, which. follow rolls crushing to 0.5 in.

Jan 7, 1913

By AIME AIME

This volume, an octavo of 626 pages, is now ready for delivery. By its aid, any subject treated or alluded to in the Transactions can be instantly tracked. The names of persons, mines, works, towns, etc., have been included; and abundant cross-references and classified sub-headings have been added to facilitate rapid consultation. Thus, the student remembering the name but not the locality, or the locality but not the name, or neither the name nor the precise locality of a gold-mine, can find it under ?Gold-mines," or under either of the other heads. For a more extended statement of the nature and use of this Index, which is intended specially for the benefit of those who do not possess complete sets of the Transactions, and who consult the Library by correspondence, see the Bi-Monthly Bulletin for September, 1907. The price of the Index bound in cloth is $5, delivery charges prepaid. Half-morocco binding costs $1 extra. Buy at once a copy of this Index, and also as many back-volumes of the Transactions as you can afford. Every such purchase from the stock on hand is so much added to the income of the Institute. As far as possible, the money thus received will be devoted to maintaining and perfecting the Library, and making it useful to members in all parts of the world.

Jan 11, 1907

By C. O. Brawner

The advent of larger drilling, excavation, and milling equipment is resulting in a tremendous increase in the scale and annual tonnage of open pit mining. At the present time, open pits up to 3000 ft. deep, and tailings dams and waste dumps up to 600 ft. high are being planned. One of the major problems that projects of this magnitude create is stability. Stability at open pit mining developments must be assessed for tailings dams, waste dumps, and open pit slopes in overburden soil and in rock. Soil mechanics principles are used to assess the stability for the first three. This science was developed by Dr. Karl Terzaghi in the 1920’s, and since that time the theories and principles have been tested and evaluated. This experience has resulted in the development of sound theoretical concepts, workable sampling and testing techniques, and accurate methods of analysis. Typical problems that can be analyzed include: -bearing capacity of soil under dams and waste dumps. - amount of seepage under and through dams. - stability of slopes and determination of safe slope angles for tailings dams, waste dumps, and open pits. - influence of earthquakes on stability. - influence and cost of different excavation and construction techniques. To assist in comparing engineering experience, an international soil classification system has been developed and used for several decades. In addition, many excellent text books are available outlining soil mechanics principles and techniques. A high degree of technology exists in soil mechanics. This, the mining engineer cannot afford to ignore. If soil mechanics principles had been applied, many major failures involving tailings, tailings dams, or waste dumps, such as those at Aberfan, Mufulira, Luanshya, and El Cobre would not have occurred. Tailings dams are planned in Canada that will be up to 600 ft. high. Construction procedures used in the past have paid little attention to the compaction of the shell material or to the influence of earthquakes on stability. This neglect has led to failures. While failures in low dams may not be too serious, for high dams such failures could have catastrophic results. Another major area of concern is the stability of rock slopes. From the standpoint of long

Jan 1, 1971

By C. F. Floe, M. Cohen, M. B. Bever, V. G. Paranjpe

P. Coheur and L. Habraken—We read this paper with great interest and are glad to congratulate the authors for their valuable work, supplying an important contribution to the mechanism of tempering on the carbides in vanadium steels. We are in a good position to appreciate this work since we have been studying, for more than a year, Cr-Mo steels of a composition similar, but less highly alloyed (namely 0.1 pct C, 3 pct Cr, 1 pct Mo). Our results are quite in concordance with the authors', however, we wish to point out that it is very interesting to use equally the electron microscope in order to observe the variations of microstructure in steels. We have studied simultaneously the evolution of the carbides in situ with the electron microscope, and, after extraction, again with the electron microscope, and then with X-rays. The first results which we have obtained have been communicated at the Congress of Delft (July 1949) and at the "Journees de la Metallurgie" in Paris (October 1949). These may be summarized as follows: After tempering with varying either the tempering temperatures or the tempering times, the carbides show two evolutions. The first one is connected to the carbides existing in the steels, principally in the boundaries of the grains. For some groups of steels these carbides may coalesce and for other groups they may

Jan 1, 1951

By N. J. Grant, D. S. Bloom

P. Coheur and L. Habraken—We read this paper with great interest and are glad to congratulate the authors for their valuable work, supplying an important contribution to the mechanism of tempering on the carbides in vanadium steels. We are in a good position to appreciate this work since we have been studying, for more than a year, Cr-Mo steels of a composition similar, but less highly alloyed (namely 0.1 pct C, 3 pct Cr, 1 pct Mo). Our results are quite in concordance with the authors', however, we wish to point out that it is very interesting to use equally the electron microscope in order to observe the variations of microstructure in steels. We have studied simultaneously the evolution of the carbides in situ with the electron microscope, and, after extraction, again with the electron microscope, and then with X-rays. The first results which we have obtained have been communicated at the Congress of Delft (July 1949) and at the "Journees de la Metallurgie" in Paris (October 1949). These may be summarized as follows: After tempering with varying either the tempering temperatures or the tempering times, the carbides show two evolutions. The first one is connected to the carbides existing in the steels, principally in the boundaries of the grains. For some groups of steels these carbides may coalesce and for other groups they may

Jan 1, 1951

By Frank R. Milliken, Robert Goodwin

In September 1937, the Ohio Copper Co. inaugurated the treatment of its copper-bearing mill tailings at Lark, Utah. These tailings had been accumulated during the regular operation of the Ohio Copper mine and mill over the period 1907 to 1919. Gravity concentration had been employed except for a comparatively short period in 1919, when flotation was used. The ore milled during that period assayed about I per cent Cu. The chief copper mineral, chalcocite, was disseminated in a shattered quartzite, mainly along fracture or cleavage planes. The quartzite gangue was extremely hard and grinding to liberation resulted in excessive sliming of the "sooty" chalcocite, with consequent high tailings losses. Recovery on the seven million tons treated was probably less than 60 per cent of the total copper content. As early as 1918, attempts had been made to sample the dump. In 1928, a complete sampling program was undertaken. The sampling consisted of seventy-four 5-in. post auger holes drilled to the full depth of the dump at regular intervals of 250 ft. Each 10-ft. portion thereof comprised a sample for analysis. Each sample was screened, rolled, divided into three parts, dried and assayed. The reject was retained for testing purposes. From the depth of the auger holes a contour map of the dump was plotted, Fig. I, which gives percentages of tonnage and copper content. The tonnage within the limit of the drill holes was estimated at about five million tons with an average content of 0.42 per cent Cu, 31 per cent of which (0.13 per cent) was acid-soluble. A screen analysis of the composite dump sample is shown in Table I. Flotation tests by several companies and individuals were then made, the results of which ranged from 62 to 74 per cent recovery. On the basis of these, a 200-ton pilot plant employing straight flotation was built and operated for a few months. Operation of this plant was unsuccessful, as no provision had been made to handle the copper-bearing solutions resulting from the water-soluble copper, a point that was overlooked in the laboratory test work. Attempts to decant the copper-bearing solution for precipitation in the usual manner ahead of flotation were not satisfactory because of low water recovery (owing to poor settling characteristics of the pulp) and contamination of the copper precipitate with unsettled slime. Low copper prices in 1931 necessitated the termination of testing. With the stimulus of higher copper prices in 1937, a review was made of metallurgical

Jan 1, 1943

By R. M. Asimow

The magnetization curves for specimezs containing superparmagnetic particles are considered. It is shown that the curves may differ from a Langezlin function because of particle anisotropy, particle interactions , and the presence of a size distribution of particles. The various causes of particle anisotropy are considered, and magnetization curves for specimens with cubic and uniaxial anisotropy are presented. The magnetization curves depend on the In the particle-size below 100A it is quite difficult to obtain quantitative size and shape information on precipitate particles. All of the available techniques have their limitations; however, quantitative applications of superparmagnetism have not been developed as fully as possible due to a lack of analysis of the complete magnetization curve. With such an analysis it appears possible to obtain from a single magnetization curve of a specimen containing randomly oriented SPM (superparamagnetic) particles a quantitative volume distribution and a description of the particle shape.* sign of the anisotropy energy and in the case of a negative uniaxial anisotropy (prolate spheroids) the resulting curves may differ very considerbly from a Langevin function. A graphical technique is developed whereby it is possible to separate out the effects of the size distribution, the particle interaction, and the particle anisotropy. Thus it is possible to obtain quantitative values for both the particle shape and the size distribution. Langevin function2 I/Is = ctnh(HVIs/k T)-k T/HVIS [ 1 ] where I, is the saturation magnetization, V the particle volume, H the applied field, T the particle temperature, k the Boltzmann constant, and I the magnetization in the direction of the applied field. Such behavior is rarely if ever observed in actual systems. One explanation for this is that the SPM particles do possess a significant anisotropy and thus the magnetic energy associated with the particle depends on the direction of magnetization in a more complicated way than for the isotropic particle of Eq. [I]. In general the magnetic energy E of an isolated SPM particle embedded in a nonmagnetic matrix can be expressed as a sum of several contributions: E = Eh + Ed+Es+Ec [2] where Eh is the external field energy, Ed the energy resulting from the particle demagnetizing factor, E, the magnetostriction energy, and E, the crystalline anisotropy energy. In each term we consider only the part dependent on the orientation of the magnetization vector and the particle axes as the shape of the magnetization curve will be determined by these contributions. Following the same procedure used in deriving the Langevin function,

Jan 1, 1965

By Robert Goodwin, Frank R. Milliken

In September 1937, the Ohio Copper Co. inaugurated the treatment of its copper-bearing mill tailings at Lark, Utah. These tailings had been accumulated during the regular operation of the Ohio Copper mine and mill over the period 1907 to 1919. Gravity concentration had been employed except for a comparatively short period in 1919, when flotation was used. The ore milled during that period assayed about I per cent Cu. The chief copper mineral, chalcocite, was disseminated in a shattered quartzite, mainly along fracture or cleavage planes. The quartzite gangue was extremely hard and grinding to liberation resulted in excessive sliming of the "sooty" chalcocite, with consequent high tailings losses. Recovery on the seven million tons treated was probably less than 60 per cent of the total copper content. As early as 1918, attempts had been made to sample the dump. In 1928, a complete sampling program was undertaken. The sampling consisted of seventy-four 5-in. post auger holes drilled to the full depth of the dump at regular intervals of 250 ft. Each 10-ft. portion thereof comprised a sample for analysis. Each sample was screened, rolled, divided into three parts, dried and assayed. The reject was retained for testing purposes. From the depth of the auger holes a contour map of the dump was plotted, Fig. I, which gives percentages of tonnage and copper content. The tonnage within the limit of the drill holes was estimated at about five million tons with an average content of 0.42 per cent Cu, 31 per cent of which (0.13 per cent) was acid-soluble. A screen analysis of the composite dump sample is shown in Table I. Flotation tests by several companies and individuals were then made, the results of which ranged from 62 to 74 per cent recovery. On the basis of these, a 200-ton pilot plant employing straight flotation was built and operated for a few months. Operation of this plant was unsuccessful, as no provision had been made to handle the copper-bearing solutions resulting from the water-soluble copper, a point that was overlooked in the laboratory test work. Attempts to decant the copper-bearing solution for precipitation in the usual manner ahead of flotation were not satisfactory because of low water recovery (owing to poor settling characteristics of the pulp) and contamination of the copper precipitate with unsettled slime. Low copper prices in 1931 necessitated the termination of testing. With the stimulus of higher copper prices in 1937, a review was made of metallurgical

Jan 1, 1943

By Eric Kula, Åke Josefsson

L. J. Dijkstra and R. Sladek, (Ontario Research Foundation, Toronto, and Institute for the Study of Metals, Chicago, respectively)—This interesting paper confirms some results obtained some years ago in collaboration with Fast: namely the broadening of the nitrogen peak by the presence of small amounts of manganese. Later on a more extensive study of this effect was made at the Institute for the Study of Metals at Chicago. As the work has not yet been submitted for publication we wish to mention here briefly some of the results. The effect of about 0.5 atomic pct manganese, chromium, molybdenum, or vanadium on the nitrogen-peak in iron was examined. The broadening found previously in the case of manganese was even found to be more pronounced for chromium. In the case of molybdenum and vanadium a double peak was observed which seemed to justify the idea that in all cases mainly two relaxation times were involved: namely, the normal relaxation time as found in pure iron and a second relaxation time related to the existence of abnormal interstitial lattice sites introduced by the foreign metallic element. The analysis showed that for the normal nitrogen-peak as a reference at 22°C the abnormal peak was found at about 32°, 47°, 75°, and 87°C in the case of manganese, chromium, molybdenum, and vanadium, respestively. In the manganese alloy the free energy difference for a nitrogen-atom at an abnormal and a normal lattice site was estimated at 2800 cal per mol. This means that for temperatures above 100°C the solid solubility and overall diffusion rate of nitrogen is not much affected by additions of 0.5 pct Mn. We believe that the difference in rate of precipitation of nitrogen in pure iron and the manganese alloy is mainly a question of the number of potential nuclei available in the different steels. In studying the effect of these alloying elements on precipitation of nitrogen, a distinction must be made between the para reaction and ortho reaction, using terminology introduced by Hultgren.7 The ortho reaction in which the alloying metallic element participates in the diffusion under formation of nitrides occurs at high temperatures such as 600°C. The para reaction in which the alloying metallic element does not diffuse and in which the nitride inherits its alloy content from the matrix occurs at lower temperatures. To prevent the ortho reaction the alloys have to be quenched rapidly from the phase. It is not surprising that the authors find that the height of the peak indicates a lower nitrogen content than chemical analysis. In the first place the peak is not a single relaxation peak and secondly, the steels were not quenched from the phase after the nitrogen was introduced at 580 °C.

Jan 1, 1953

By Sterling G. Valentine

The annual .use of large quantities of sulphurous iron-ores (over 1,500,000 tons in the United States) has led to a search for the best methods of desulphurization, in order to make this material more available for the manufacture of a good quality of pig-iron. Although such ores can be used raw in small amounts, they must be previously roasted if they are to constitute the entire ore-charge of a furnace.

Jan 1, 1890

By J. P. Hammond, C. J. McHargue, S. E. Adair

Cold-rolled sheet textures have been determined for binary solid solutions of aluminum, columbium, tantalum, and zirconium in titanium. An alloy containing 3.8 pct Al had a (0002) [10101 texture, whereas alloys with the other elements had rotated (0002) [10101 textures similar to that of iodide titanium. THERE have been relatively few studies of the effect of alloying on deformation textures. A second element may be present in the base metal in solid solution and/or as a second phase. The literature offers no satisfactory explanation for the effects of solid solution alloying on textures noted thus far. For example, there is no satisfactory explanation of the difference in the textures of copper and a brass. The most complete study of the effects of solid solution alloying on deformation textures has been that of Brick, Martin, and Angier.¹ These investigators reported that the copper texture was retained by alloys of copper with up to 30 pct Ni, less than 5 pct Zn, less than 2 pct A1 or Co up to the limit of solubility. Copper containing more than 5 pct Zn, more than 2 pct Al, or the maximum soluble concentration of tin, silicon, or manganese showed the deformation texture of a brass. Bakarian² reported that additions of 0.20 pct Ca to 99.98 pct Mg or 2.0 pct Mn plus 0.15 pct Ca to magnesium resulted in entirely different textures than for the pure magnesium. The texture obtained for high-purity magnesium sheet showed the basal plane to be concentrated parallel to the rolling plane. The texture obtained for the alloy containing 0.20 pct Ca had the basal planes concentrated in elliptical areas whose centers were tilted 15" from the center of the pole figure toward the rolling direction. This split basal orientation was even more pronounced in the alloy containing 2.0 pct Mn and 0.15 pct Ca. Fuller and Edmunds" studied the rolled sheet textures in a zinc alloy containing 1 pct Cu and 0.01 pct Mn. The basal pole figure of this alloy contained a region of strong concentration not found in the pole figure for pure zinc.' In the above cases, results were discussed in terms of possible changes in slip and/or twinning systems and critical shear stresses. However, there were no experimental data to relate these speculations with the observed textures. It has been suggested that the deformation textures of titanium, zirconium, and beryllium could be directly ascribed to their low c/a ratios. The complex deformation mechanisms of titanium" also have been suggested to be characteristic of hexagonal close-packed metals with low c/a ratios. The purpose of this investigation was to study the cold-rolled sheet textures in binary titanium-base a alloys in which the c/a ratios were greater than, less than, and about the same as the c/a for iodide titanium. The annealed textures of these alloys will be reported in a subsequent article. Materials and Methods The chemical analyses of the metals used in this investigation are given in Table I. The alloys were prepared as 15 g buttons on a water-cooled copper block in a vacuum arc-furnace. The furnace was evacuated to pressures of the order of 10.' mm Hg, flushed with 99.98 pct pure argon, and melting was carried out in 0.2 atm pressure argon. Each button was remelted until radiographs and chemical analyses indicated complete solution of the solute elements. All buttons were forged and homogenized 72 hr at 500°C. The buttons to be rolled were ground and etched to sizes and shapes suitable for the rolling

Jan 1, 1954

1. Any society of undergraduates at a technical school, comprising students in any branch of engineering, metallurgy, chemistry, geology, etc., may be recognized by the Board of Directors in its discretion as an Affiliated Student Society, and its name, together with the names of its President and its Secretary, may be published in the Bulletin or the Year Book of the Institute. The individual members of such a society will not be catalogued as individual members or associates of the Institute, but may at any time be proposed for election as members or associates of the Institute, in the usual way. 2. Membership in an Affiliated Student Society, certified by the official representative thereof, and accompanied with suitable testimony as to character and qualifications, will have special, weight with the Membership Committee of the Institute, in its consideration of the proposal of a candidate for membership or for Junior membership.

Jan 1, 1923

1. Any society of undergraduates at a technical school, comprising students in any branch of engineering, metallurgy, chemistry, geology, etc., may be recognized by the Board of Directors in its discretion as an Affiliated Student Society, and its name, together with the names of its President and its Secretary, may be published in the Bulletin or the Year Book of the Institute. The individual members of such a society will not be catalogued as individual members or associates of the Institute, but may at any time be proposed for election as members or associates of the Institute, in the usual way. 2. Membership in an Affiliated Student Society, certified by the official representative thereof, and accompanied with suitable testimony as to character and qualifications, will have special, weight with the Membership Committee of the Institute, in its consideration of the proposal of a candidate for membership or for Junior membership.

Jan 1, 1923

1. Any society of undergraduates at a technical school, comprising students in any branch of engineering, metallurgy, chemistry, geology, etc., may be recognized by the Board of Directors in its discretion as an Affiliated Student Society, and its name, together with the names of its President and its Secretary, may be published in the MINING AND METALLURGY of the Directory of the Institute. The members of such a society will not be named individually on the membership list of the Institute, but may at any time be proposed for election as associates or junior associates of the Institute, in the usual way. 2. Membership in an Affiliated Student Society, certified by the official representative thereof, and accompanied with suitable testimony as to character and qualifications, will have special, weight with the Membership Committee of the Institute, in its consideration of the proposal of a candidate for membership or for Junior membership.

Jan 1, 1923