Search Documents

By T. J. DeMull

More than 1.81 mt (2 million tons) of low grade ore have been heap leached at the Alligator Ridge mine. Since inception of leaching in 1980, several modifications have been made to ore agglomeration, heap construction, and leach operation practice. These modifications have improved the percolation rate of the ore and the rate of gold extraction from the ore. Changes made in each of these areas are described and the effects of the changes are discussed.

Jan 1, 1984

By Donald C. Violetta

LIMITATIONS of the sintering process as applied to the agglomeration of fine iron-ore concentrates are related directly to the sizes and aggregating properties of the ore particles. A normal sintering mixture is composed predominantly of material which ranges in size from 5/8 in. to 100 mesh, whereas concentrate is composed of material which ranges in size from 100 mesh to less than 10µ. Unless the concentrate has high aggregating properties, it is quite impervious to a gas stream and, as such, inhibits the capacity and operability of the conventional sintering process. Material has Poor Aggregating Properties Aggregating properties, in this case, may be defined as the ability to form small agglomerated fragments or accreated masses by a normal mixing action, and the ability to maintain these shapes during drying and firing. Coarse-screened ores are a natural aggregate, and fine, slimey ores have good aggregating properties. However, specular-hematite flotation concentrate has a very low tendency to aggregate, due to its particle sizes, shapes, and surface chemistry and, as such, is readily air borne in a gas stream when dry.

Jan 3, 1958

By Roger G. Rowe

In late 1980, Exxon Minerals Company performed rock mechanics testing on oriented 150 mm drill core from their 75Fi tonne massive sulfide deposit near Crandon, Wisconsin. Instrumented samples from depths of 300 meters indicate premining horizontal stresses in a north-south direction (parallel to pillar faces) to average 12,300 kPa, with the perpendicular plane yielding an average stress of 14,630 kPa. Rock strength versus sample size was compared using uniaxial compressive strengths from 47 mm, 95 mm and 150 mm core. Massive sulfide averaged 153,300 kPa, 139,845 kPa and 75,330 kPa respectively, while the hanging wall and foot- wall averaged 92,000 kPa, 76,560 kPa and 57,960 kPa respectively. Point load compressive strengths were calculated using formula suggested by both Hassani et al., 1980 and Broch et al., 1972. Values calculated using the Hassani formula closely resembled pre- existing point load and uniaxial compressive strengths, while values calculated using the Broch formula were 50 percent low.

Jan 1, 1982

By David Branch, Martin J. White, Faramarz P. Hassani

The work presented in this paper is part of an overall research programme into the problem of stability of main access roadways driven in Coal Measure strata. Data about the post-failure behaviour of rocks are generally of a qualitative rather than quantitative nature. This investigation represents the initial part of a long-term research project aimed at quantifying the post-failure properties of Coal Measure rocks and to investigate their effects on tunnel stability. The results of tests conducted to evaluate the post-failure strength characteristics of Coal Measure rocks under uniaxial and triaxial stress conditions are presented. Empirical failure models are proposed to define the triaxial intact and residual failure properties of these rock types. The application of such data to closure prediction techniques of underground excavations are outlined and discussed.

Jan 1, 1984

By V. J. Bishop, R. G. Beverly

Recent publicity has focused attention on the hazard of lung cancer among uranium miners. Many mining people feel the danger has been exaggerated. Whether or not this is the case, the industry must thoroughly evaluate this potential hazard and take corrective measures to minimize the threat of radiation after-effects and to maintain the level of radiation in mines within the presently-accepted limit. The measurement and control of radon gas and its solid radioactive decay products, Po-218, Pb-214, Bi- 214, and Po-214, should be the one facet of most concern to uranium miners in any radiation control program. To illustrate the radioactivity involved with small quantities of radon gas, the activity from the decay products of five milliliters of radon gas (imagine a 5-ml vial) would be adequate to raise one cubic mile of air to seven times the recommended maximum working level of 300 [ ] (micro micro curies) per liter. This would be enough radioactivity to raise to the maximum working level a 6 x 8-ft drift which extended around the world 160 times. Obviously, a little radon gas goes a long way.

Jan 8, 1961

By Bert Sandell

MUCH has been said and written about the various uses of die-castings, their applications in the various industries and their advantages and disadvantages. Examination of this literature, however, fails to disclose any data concerning the effect of temperature upon any of the physical properties of die-casting alloys. The uses and applications of die castings are so numerous, and of such a varied nature, that far too lengthy a manuscript would be required to list all of them. Brief mention of some specific cases will suffice to illustrate the temperature ranges in which certain die castings function. Automobile hardware, such as hub caps, door handles, radiator caps, etc., can be used as one example. Castings of this type are constantly exposed to varying climatic conditions, temperatures ranging from below zero to upwards of 100° F. Refrigerator parts, such as ice-cube trays, etc., form another example. Approaching the other temperature extreme, we encounter conditions such as are found in kitchens in which oven-heat indicator parts, cooking utensils, waffle grids, etc., embody use of die castings, where temperatures as high as 500° F. are often met with. Because of this variation in service temperatures, it was felt necessary to ascertain the effect of these temperatures upon the physical properties of die-casting alloys. The Charpy impact test was chosen first because of its simplicity, and because of the fact that brittleness is more likely to be objectionable in die castings than hardness or other physical properties.

Jan 1, 1932

By Alvin W. Schillinger

During the past ten years, the Calumet Div. of Calumet & Hecla, Inc. has conducted extensive exploration and mining in the footwall of the Osceola amygdaloid lode in the native copper district in Michigan's Upper Peninsula. In an attempt to delineate more clearly the extent and nature of high-grade footwall copper mineralization, 876 diamond drill and long steel holes aggregating slightly more than 47,000 ft have thus far been drilled from the accessible hanging-wall workings. Early in this program it became obvious, through inspection of footwall workings in progress, that due to the erratic and bunchy occurrence of the native copper in the footwall zone, the exploration drilling was failing to outline completely the extent of the oreshoots. Early drilling results indicated isolated pockets of ore whereas in actual practice the footwall was found to be fairly thoroughly mineralized in shoots within the ore zone. Based on drill results only, the "success factor" (discovery ratio) was only 34%.

Jan 11, 1964

By H. B. Charmbury, D. R. Mitchell

Everyone in the coal industry from top management to the preparation engineer is vitally interterested in recovering as much salable coal as possible from the run-of-mine product. Coal losses from a preparation plant occur in the solid refuse material being discharged from the plant and in the bleed-off slurry from the water circuit. The refuse is generally hauled from the plant in solid form by trucks, conveyors, or aerial trams to the refuse or culm banks or it may be crushed and transported by hydraulic methods to refuse ponds or dams. The loss of coal in refuse material and the extent of this problem has been covered in another paper. The loss of salable coal in the plant bleed-off slurry is one of the water circuit problems in coal preparation plants. Slurries originate at various places in the processing circuits and are usually disposed of by transportation to waste ponds known as slurry ponds. Even though the combustible material discharged as slurry and refuse from the plant is labeled a loss, the loss must only be considered temporary. There is a tendency at the present time to examine refuse and slurry losses and to reprocess these materials to recover valuable coal.

Jan 1, 1960

By M. R. Hoover, J. H. Kim, S. J. Kloda, R. E. Carmola

Feed preparation circuits, which involve such unit processes as size reduction, classification, and beneficiation are inherently a capital and operating cost intensive part of synthetic fuels plants. These circuits, as encountered in similar minerals industry operations, have until now been designed more or less by individual experience and preference mainly because of the large number of variables involved. As a first step towards a computer-aided design tool, a flowsheet simulator has been developed based on an executive program which can connect and drive modular subroutines according to the proposed circuit. The most efficient and appropriate mathematical models were selected as modular sub- routines among available sources such as SPOC, ASPEN, and DOE. Advantages and limitations of this kind of approach are discussed from the system architecture and methodology transfer standpoints with special emphasis on synfuels circuits.

Jan 1, 1983

By E. Northcott, I. M. LeBaron

Before describing the electrostatic processing of feldspar, it might be well to review some of the basic definitions and terminology of feldspars. The feldspar minerals constitute a group of alumino-silicates of potassium, sodium, and calcium. Barium feldspar sometimes occurs naturally but is very rare. Hardness varies between 6 and 6.5 and specific gravity between 2.5 and 2.8. Color is generally white or pale shades of red, yellow, or green. The approximate chemical composition of the principal feldspars is given in Table I. The albite (sodium aluminum silicate) and an orthite (calcium aluminum silicate) feldspars are the end members of a series called plagioclase. These two molecules form a complete solid solution series ranging from pure soda feldspar at one end to the pure lime feldspar at the other end. Intermediate solid solutions are known as oligoclase, andesine, labradorite, and bytoconite. The general structure throughout this series is the same. Sodium and calcium may replace each other and silicon and aluminum may replace each other in the structure.

Jan 10, 1958

By Thomas Crowe

Much has been written upon the precipitation of metals from cya-nide solution by zinc. We often read of the many factors that influence precipitation, such as zinc surface, purity of zinc, percentage of lead, temperature of solutions, strength of solutions in cyanide or alkali, etc. Little do we hear, however, of the part that oxygen plays in precipitation. Caldecott1 says: "As the dissolving of gold is essentially an oxidation process, so its precipitation is one of reduction." All who have studied or worked with cyanide solutions will agree that Caldecott's statement is true. In the cyanide work in the mills of the Portland Gold Mining. Co., we have always found oxygen to be the greatest enemy to precipitation. OXYGEN ANTAGONISTIC TO GOOD PRECIPITATION A few years ago, while making some experiments on the effect of pressure upon the dissolving rate of gold front our ores, to prove a point, I made some bottle tests under vacuum. The results were surprising, and showed that under vacuum practically no gold dissolved, which confirmed my belief that Elsner's equation was true and also led me to investigate the amount of dissolved air carried by solutions at atmos-pheric pressure. The experiment consisted in partly filling an acid-bottle with mill-solution and connecting it by a rubber hose to a vacuum pump. When the vacuum was suddenly applied, a cloud composed of. thousands of small air bubbles rose out of the solution, showing qualitatveily the . amount of dissolved air that was contained in the solution, and also proving that the relief of atmospheric pressure on the solution permitted this dissolved air to escape.

Jan 8, 1918

RUfUs J. Foster, Scranton, Pa. (communication to the Secretary*) :—In answer to one of the inquiries made of Mr. Conner, and as a matter of historical record, I beg to say that the idea of supporting the strata over worked-out areas in coalmines by flushing the openings full of culm originated and was put into actual practice by the late R. C. Luther, a former member of the Institute, at that time Chief Mining Engineer, and later General Manager, of the Philadelphia & Reading Coal & Iron Co. In the early 80's the Philadelphia & Reading Coal & Iron Co. purchased from Messrs. Hecksher & Co. the Eohinoor colliery, situated in the western part of the borough of Shenan-doah, Pa. On taking possession of the colliery the Philadelphia & Reading Coal & Iron Co. made a conlplete resurvey of the mine-workings, giving an absolutely correct map which showed not only the plan of the mine-workings, but also every improvement on the surface over the workings, and the marked features of the surface of the ground. Tidal elevations were shown at every eurvey-station in the mine and on the surface, so that, as is the case with all the maps of the company, contour-maps of either the surface or the bottom of any coal-seam, or geological cross-sections, could be constructed directly from the information on the mine-maps. In a cornparatively short time after the company took possession of the colliery, the workings which extended under the western portion of the borough of Shenandoah began to cause trouble and damage dwellings and other buildings in that section of the town. The lots in this section had been sold, in many cases, to individuals by the Gilbert & Shaefer Estate, owners of the coal-lands on which the colliery was located. In

Jan 1, 1912

By J. D. Lubahn, R. P. Carreker, J. G. Leschen

The formation of slip bands in crystalline solids undergoing plastic deformation has recently been treated as a problem of nu-cleation and growth.' A simplified theory was developed and shown to be qualitatively consistent with certain experimental observations reported in the literature, such as the frequent failure of slip bands to traverse the entire crystal, the effect of specimen diameter and temperature on the yield stress, and the occurrence of incubation periods in the deformation of suddenly loaded crystals. The theory further predicts the appearance of transients in the rate of strain of a crystal when the applied stress is suddenly changed from one constant value to another. A transient consists of a discontinuous change in the strain rate followed by a gradual approach to a steady-state value. Such transient behavior apparently has not been recognized in previous experimental work. The preliminary experiments reported in the present paper were undertaken to confirm the existence of the predicted transients and thus to determine whether a more detailed treatment of the nucleation theory of slip might be theoretically and experimentally fruitful. Experimental Procedure A simple creep apparatus was assembled as shown in Fig I. Very little insulation was used on the furnace in order to facilitate rapid changes of temperature. Temperature was measured with a thermometer placed in the center of the furnace and was controlled by adjusting the Variac setting. The specimens were cold-headed in split-cylinder grips. The strain was measured as total elongation by a dial gauge sensitive to I/I0,000-in movement of the weight pan. Since the specimen gauge lengths were

Jan 1, 1949

By H. N. Lawrie

This study was undertaken on account of the lack of definite knowledge concerning the influence of bismuth on wire-bar copper, and the small elimination of bismuth from copper-matte during the smelting-operations. The early workers who studied the influence of bismuth on copper confined their investigations to malleability and ductility—two physical properties which are related to the others so intimately that their determination is of primary importance. Karsten and Levo1,² using bending- and mealleability-tests, seem to have been the first to take up the subject, and while their results are incomplete, they agree in the main with the later work of Hampe.3 The bending-tests used by the first investigators consisted in bending the specimen until it failed. The malleability-tests were made by beating the material to a knife-edge with a hammer. Hampe not only determined the percentage of bismuth which would cause red-shortness and cold-shortness of the alloy, together with other influences of bismuth on the malleability and ductility of copper, but also took up the influence of the bismuth protoxide, BiO, on copper, and of bismuth sesquioxide, Bi,O,, on the copper protoxide, CuO. Hampe's conclusioris of the influences of these two latter compounds of bismuth on copper are as follows : "If the protoxide of bismnth be alloyed with metallic copper, it is not changed to metallic bismuth, but remains mechanically distributed throughout the copper.

Jan 1, 1910

J. L. McK. YARDLEY,* Pittsburgh, Pa. (written dlscussion ?) .-It is interesting to observe how closely Mr. Hansen agrees with other investigators to the effect that the art of electrolytic zinc has left the realm of mystery. In his introduction, lie has said practically what Thomas French said in his paper "The Future of Electrolytic Zinc. "1 The successful electrolysis of zinc from sulphate solutions has not been an easy matter, and it is only within recent years that the difficult problem of depositing high-grade zinc has been satisfactorily: accomplished on a commercial basis. The principal requisite is. that the electrolyte shall be quite free from certain impurities. The methods by which freedom from these impurities is assured are now very well understood, and with experienced superintendents there is little difficulty in obtaining a high efficiency in that part of the process. When certain underlying principles are recognized, the difficulty encountered in dealing with the filtration of the acid and slimy solutions also largely disappears, although it has been a very serious one to the uninitiated. In the dissolving of the zinc from the roasted ore, there is nothing which any competent chemical' engineer cannot undertake, and any other operations connected with the electrolytic process are either of little or no difficulty, or are common to the retort process. Mr. Hansen also agrees with R. G. Hall's statement in " Some Economic Factors in the Production of Electrolytic Zinc:"2

Jan 10, 1918

By Donald L. Everhart

Beginning in 1906, data has been compiled on the distribution of uranium in phosphate de- posits. Particular emphasis has been placed on uranium in phosphate by a number of geologists and geochemists in the US Geological Survey in research sponsored by the US Atomic Energy Commission (now Nuclear Regulatory Commission) and the US Department of Energy (DOE) during the 30-year period from 1951 to 1981. A comprehensive study of uraniferous phosphate resources the United States and the Free World was completed, under the auspices of DOE, in 1979. Apatite is the main carrier of uranium in phosphate. Uranium generally replaces calcium in the mineral lattice. In marine phosphorite throughout the world, the uranium content is characteristically in the range of 0.005 to 0.02% by weight. Phosphorite takes in uranium by structural substitution in apatite or other mineral phases, by absorption, or by the formation of independent mineral phases. Apatite derived from the interaction of ground water, guano and limestone is typically relatively low in uranium content-in the 0.001 to 0.005% range. In primary accessory apatite of igneous rocks, as well as magmatic and metasomatic apatite segregations of alkalic rocks and carbonatite, uranium content is generally between 0.001 and 0.01%. In all these phosphate deposit types, secondary enrichment of uranium through

Jan 1, 1983

By P. F. Richardson, J. L. Perisho, W. J. Roe

Handling and transport of coal during the winter months can be a severe problem. The inability to unload frozen coal from rail cars produces serious economic and logistic problems due to transportation delays, rail car shortages, and demurrage on the rail cars. One method of dealing with the problem of unloading frozen coal has been to spray freeze conditioning agents onto the coal before it is loaded into rail cars. Both water soluble and oil based formulations have been used as freeze conditioning agents. The water soluble treatments generally contain a polyhydroxy alcohol, such as ethylene glycol, or salts of alkaline earth metals, such as magnesium chloride and calcium chloride, as freeze point depressants. The oil based treatments consist principally of hydrocarbons, such as No. 2 oil or diesel fuel. The authors' tests have shown significant differences in the effectiveness of these freeze conditioning agents, depending on the particular coal substrate being treated. These differences correlate with the coal porosity and inherent moisture of the substrate. In general, the greater the porosity of the coal, the smaller the effect of the freeze conditioning agents. Coal porosity has a greater impact on water soluble freeze conditioning agents than oil based products. The authors investigated the pore structure of a variety of coals using mercury intrusion. Findings were related to the effectiveness of different freeze conditioning agents as measured by unconfined compression strength tests. In general, coals with a large number of very small pores (between 0.05 µm and 0.03 µm) do not respond as well to freeze conditioning chemicals.

Jan 1, 1986

By D. R. Snow

The year 1930 stands out in the petroleum industry as an exceptional one in many ways. It is one of the few years in its history during which crude oil production declined from that of the previous year in nearly every important producing district in the United States and in the world as a whole. World production of crude oil declined approximately 81,000,000 bbl., from 1,484,451,000 bbl. in 1929 to 1,403,500,000 bbl. in 1930. Production of crude oil in the United States declined approximately 111,000,000 bbl., from 1,007,323,000 bbl. in 1929 to a production of 896,265,000 bbl. in 1930. World production outside of the United States increased approximately 30,000,000 bbl., due principally to the increased production in Russia. This, together with the decided decrease of production in the United States, resulted in a smaller percentage of world production in the United States than in any other year since 1921. This declining production occurred in the face of the greatest visible supply in the form of potential production that the industry has ever known and was clearly the result of the great efforts put forward to restrict production, both by proration and by unitization. Throughout the year, developments along the lines of proration and unitization have overshadowed all other developments in the minds of those interested in the oil industry and will, no doubt, continue to do so more and more in the future, as it is quite evident that the industry cannot hope to maintain itself in a profitable position, without some rational plan of bringing about a better balance between supply and demand than has existed in the past. The successful operation of the Van field unitization agreement and the recently completed Kettleman Hills plan are indicative of what mag be expected in the future along this line. That real progress has been made in this direction is shown by the fact that total crude oil stocks in the United States were decreased by approximately 28,000,000 bbl. during the year 1930. This is the only year on record during which such a decrease of crude oil stocks was accompanied by a severely declining price structure. This reduction of crude stocks is apparently continuing even after the price has reached its present low level, indicating that there is no

Jan 1, 1931

LET us return and follow our first intention of discussing the art of melting. Since I have demonstrated to you how large works are made, you may have thought that the way to the small ones was also open to you, and you would not have been mistaken. But in order to avoid work and expense there are shorter and easier ways to be used, both because the things can be handled more easily and because it is not necessary to have so much regard for the forces of small materials. Therefore, wishing to make a distinction for you, I shall call this the small art of casting. Before speaking of this, I shall tell you of several methods of making powders for moulding. Then I shall also tell you of the methods of moulding in boxes and in frames, and how the said powders are to be prepared for casting either dry or green. Then I shall tell you some methods that are held as secret by the masters for handling the metals in melting and making them flow readily, so that you may easily fill the cavities of your moulds.

Jan 1, 1942

Why should I pay $8.50 an hour for dealer repairs when my own mechanics work for $3.50?" The numbers vary, but that's the argument most contractors use to justify doing their own repairs. They don't realize it, but they're probably losing big money. For instance, it takes nearly a quarter of a million dollars in tools alone to equip a shop comparable to an average equipment dealer's facilities. A contractor must buy a lot of expensive, specialized tools he seldom uses, or else settle for the inefficiency of having repairs done by his mechanics with relatively unsophisticated tools. His building soaks up money in rent, maintenance insurance, taxes. His mechanics demand good wages. It even costs money when mechanics aren't repairing equipment. Mechanics get full wages for slack periods and cleanup time, too. This doesn't count as service manhours, but it's still part of the total repair cost. To help contractors uncover these hidden expenses and find out the true cost of owning a shop, some equipment dealers have devised a do-it-yourself "shop cost analysis form."

Jan 1, 1970