Search Documents

By Willis Carrier

PARTICULAR interest in the ventilation of deep mines, especially those in South Africa, has been created by a very complete system of cooling of the world's deepest mine, the Turf shaft of the Robinson Deep ill Johan-nesburg. The writer visited this mine in January, 1936, and again in 1937. During these visits and subsequently, a considerable part of the theory involved in rock cooling in tunnels was developed and this has been checked by practical observations of the rates of rock cooling made within mines. The purpose of this paper is to set forth the method of attack of the mine problem. The cooling or air conditioning of mines by the use of mechanical refrigeration was not wholly new 1-5 when the Robinson Deep installation was made. The first mine to be cooled was the Morro Velho mine, in Brazil. The first installation in this mine was put into operation in December 1920, the refrigerant being ammonia.5 The surface cooling gave considerable benefit but it proved inadequate as greater depths were reached, therefore in 1929 two centrifugal refrigerating machines were installed at the 6000-ft. level. These were used in conjunction with the surface cooling system to furnish additional cooling at the lower levels. This later installation used Carrene as a refrigerant. This nonflammable refrigerant, having a boiling point of 104° at sea level, insured reasonable safety, since all parts of the machine operated At subatmospheric pressure. Very favorable reports have been received on the effectiveness of this installation, but no recent data are available. An interesting feature of that plant is that the condenser water is cooled by spraying it into the exhaust air from the mine at the base of the ventilation upcast, which permits the water to be cooled within a few degrees of the wet-bulb temperature of the air entering the upcast, and the only water that has to be supplied for condensing purposes is that lost by evaporation, or about 0.5 per cent of the volume circulating through the condenser. This plan affords an ideal means for the removal of the heat load from the refrigerating system, and of course also from the mine itself. In many mines, however, especially those in South Africa, there is no

Jan 1, 1938

By R. F. Mehl, C. E. Birchenall

SINCE Maxwell1 first considered the self-diffusion process in 1872 its importance in the kinetic theory of matter has been recognized. Until the discovery of isotopes in 1913, a direct measurement of this quantity seemed impossible. The only information that could be gathered indirectly was for gaseous systems for which the kinetic theory was well developed. When methods of direct observation be-came available, investigations on self-diffusion were carried out in condensed phases. In metals these data are presumably of potential importance in the study of recovery, recrystallization, creep, sintering, and related phenomena. Following the pioneer work of Von Hevesy2 and his collaborators, who determined the rate of self-diffusion in lead with the naturally occurring thorium B isotope, several metals have been investigated. Pb, Ag³, Au.6,5, and Cu6,7,8,9 are examples of isotropic crystals existing in only one phase modification. Anisotropy of diffusion has been demonstrated in Bil6 and Znll. This paper is a study of a single metal in two allotropic forms and also of self-diffusion in a body-centered cubic lattice. Despite the fact that the measurements in each of the papers cited on self-diffusion in copper seem to be internally consistent to about 10 to 15 pet, the curves reported by different authors differ by factors of 2 to 4 at the same temperatures. This uncertainty may account, in part, for the failure to establish a successful correlation between the self-diffusion rates and other physical characteristics of the metals. No satisfactory theory of metallic self- diffusion has as yet been proposed to account for all the existing data and to permit estimation in other metals. Experimental Part: Two units of radioactive iron were used in these experiments, each a mixture of Fe53 and Fe59 (12). Fe53 decays by K electron capture and the emission of an X ray with a half life of about 4 years. Fe59 emits two beta spectra, one with a maximum energy of 0.26 Mev, the other 0.46 Mev, and gamma rays of 1.1 and 1.3 Mev, with a half life of about 44 days. They were present in nearly equal concentration initially. The composite half life started at about 50 days and increased as the Fe59 decayed, leaving Fe55 relatively more abundant. After aging a year, the half life was too long to measure significant decay in a month. The absorption properties also changed with time. Because of the importance of the absorption coefficient in the diffusion calculations, it was necessary to determine this quantity frequently over the period during which these experiments were carried out. This correction was unsuspected at the time of publication of notesl3 on this work and accounts for the discrepancy in alpha iron and for part of the discrepancy in gamma iron.* * The data in the present paper supersede those given in the notes entirely. In one note the scale of log D was inadvertently reversed. In addition to the correction for the drift in absorption coefficient, the D values for gamma iron at low temperatures were high owing to insuficient correction for diffusion occurring during heating and cooling through the high temperature part of the alpha range at a rate much slower than that employed in the runs reported here. The high temperature alpha rates are much higher than the low temperature gamma rates and correspond to large equivalent times at these temperatures. These experiments were discarded and new measurements taken. Independent experiments with the same activity units indicated a radioactive contaminant in the iron, but exhaustive attempts to isolate and identify it chemically failed. These experiments? indicate † These experiments will be discussed in a later publication from this laboratory. that the contaminant represented only a trace of little importance in the diffusion results. The active iron was plated from an iron chloride solution. Enough of the solution was dropped on a 1% in. square of filter paper to wet it thoroughly.

Jan 1, 1951

MEMBERS, JUNIOR MEMBERS, ASSOCIATES AND JUNIOR ASSOCIATES LIST OF MEMBERS ALPHABETICALLY ARRANGED EXPLANATION OF SYMBOLS ** Junior Member. t Associate. || Junior Associate. Members are not marked. Capital letters signify Honorary membership. Student Associate and Rocky Mountain members on pages 165-167. Abadilla. Quirico A Catanawan. Tayabas, P. I. Abbey. Robert Graham. District Mgr The W. W. Sly Mfn. Co., 60 Church St New York. N. Y. Abbott. A. N Mines Supt Mazapil Copper Co Ltd . .Conception del Oro. Zac., Mexico. Abbott. Ckrence E Mgr Mines & Quarries, Tenn. Coal. Iron & R. R. Co 1242 Brown Marx Bldg Birminrham. Ala. Abbott. Louie Benjamin. Chief Enar Consolidation Coal Co Elkhorn Div .Jenkins, KY. Abeel. Gsorge H Jr., Cons. Min. Enar .Box 427. Santa Monica. Cal. Abel. Albert E Asst. to Pres Valley Mould & Iron Corp Hubbard. Ohio. Abel. Raymond L. Asst. Prof., Dept. of Pet. Refin Univ. of Pittsburgh Pittsburgh. Pa. Abernathy. George Elmer. Prof. of Geol. & Min Kansas State Teachers College. Pittsburg. Kans. IlAbernethy. D. Carl, Jr. Min. Engr Hudson Coal Co .Scranton. Pa. Abey, Hiroshi. Min. & Met. Engr., Min. & Met. Dept., The Higher Technical School, Osaka. Japan. tAbarn, Robert H Instructor in Met Harvard University Cambridge, Mass tAbozeid,Mahmood. Pet. Production E r . . Marland Oil Co. Ponca City, Okla. Abraham. Arthur W Geol., Richfield Oil Co Box 788. Bakersfield, Cal. Abraham, W. E. V Member, Staff of Burmah Oil Co Ltd. Nyaunghla. Upper Burmz, India. Abrahams. Alexander I Gen'l Mgr., Racon Electrical Co Slough, Bucks England. tAbrahammn. C. W Min. Engr The Mond Nickel Co Ltd . Coniston, Ont Canada. IlAbmn. Guy W., Asst. Metallographist, Youngstown Sheet & Tube Co., Research Dept., Youngstown. Ohio. Abstein. Henry T., Engr. & Mgr Profile-Tamarack Mines Co . .Yellow Pine, Idaho. tAcker. E. O'C Met I28 East Washington Lane. Germantown, Philadelphia. Pa. Ackerman. D. E Met. Research Lab International Nickel Co Inc Bayonne. N. J. tAbckerman. Ernest R Pres., Lawrence Portland Cement Co . .Plainfield. Union Co N. J. ||Ackerman. George F Jr. Min. Engr El Potosi Min. Co. .Apt. 13. Chihuahua, Chih Mexico. Acres, T. H Geol. Dept Valuation & Pet. Engr., Richfield Oil Co. 655 S. Flower St Los Angeles. Cal. Adachi. Jinzoo Address Wanted. Adair. Arthur C Valuation Enar., Internal Revenue. Treasury Dept., Washington, D. C. Adam. John. Min. Ennr., The Zinc Corp. Ltd., Box 4 C. Broken Hill, N. S. W Australia. Adami. Arthur E V. P Montana State School of Mines.Butte, Mont. Adami. Charles J Min. Ensr St. Joseph Lead Co 4540 Lindel Blvd., St. Louis, Mo. Adams. C. W.729 South Normandie St LaGranada Apt Los Angeles, Cal. Adams. Cmyler Geerwwd. Minn. Adams. F. J Gen'l Anent. Gulf Production & Pipa Line Cos .Fort Worth. Tex. ADAMS. FRANK DAWSON. Logan Prof. of Geology and Dean, Faculty of Applied Science, McGill Univ Montreal. Que Canada. Adama, Gale L Research Enar., General Pet. Corp. of California, Higgins Bldg Los Angeles. Cal. Adams. George I, Prof. of Geol. & Mineralogy Univ. of Alabama, Tuscaloosa, Ala. Adams. H. H Cons. Geol Room 416, W. T. Waagoner Bldg Fort Worth. Tex. Adams, Henry. Cons. Min. Ennr 1050 Edgewood Ave., Plainfield, N. J. Adams, Henry H.285 Madison Ave., New York. N. Y. Adams, Henry Farnum. Engr., Charge. Experimental Work. Inspiration Concentrator, Inspiration Cons. Copper Co Box 354. Inspiration. Ariz. Adams. Huntington. Min. Enar I41 Broadway, New York. N. Y. Mama, Leland D., V. P., Leslie-California Salt Co 166 Montgomery St., San Francisco, Cal. Adams, Louis W., Illinois Steel Co .Gary. Ind.

Jan 1, 1929

PUGET SOUND LOCAL SECTION. Executive Committee. CHESTER F. LEE, Chair roan. C. R. CLAGHORN, Vice-Chairman. JOSEPH DANIELS, Secretary-Treasurer, University of Washington, Seattle, Wash. W. C. BUTLER. AL K. RODGERS. On the evening of Tuesday, Sept. 2, an informal dinner was held at the University Club, Seattle, Wash., at which the Secretary of the Institute was present, and a valuable and interesting conference took place concerning the recent activities of the Institute and the relations of the Institute management to the Local Sections. SOUTHERN CALIFORNIA LOCAL SECTION. Executive Committee. THEODORE B. COMSTOCK, Chairman SEELEY W. MUDD Vice-Chairman. FREDERICK J. H. MERRILL, Secretary-Treasurer, 300 Germain Building, Los Angeles, Cal. C. COLCOCK JONES. FRANK ROBBINS. Maintains headquarters at 300 Germain Building, Los Angeles, Members of the Institute are invited to visit these headquarters whenever they are in the city. A reception was held at the headquarters of the Section on Wednesday, Sept. 10, at 8 p.m., to meet the Secretary of the Institute and discuss Institute activities and affairs. Light refreshments were served, and about 20 members of the Section attended.

Jan 10, 1913

By Harold Margolin, W. R. Hibbard, R. W. Fenn, H. P. Moore

Deformation lines, also called etch markings or strain markings, are non-effaceable lines developed in individual grains by etching a metal specimen which has been cold worked sufficiently to cause atomic non-conformity or slight orientation differences within the grains. Etching occurs more rapidly at these lines of high chemical reactivity to produce a result similar to that revealing grain boundaries. Wider etching effects forming bands have been found. They are believed to be bands of deformation lines which form areas of measurably different orientation from the crystal matrix. The crystallite rotations causing these bands have been shown by Barrett2 to contribute to deformation textures. Although deformation lines have been observed in many metals, the amount of deformation requireti for their appearance has been established only in general terms. Mathewson and Phillips3 observed the first appearance of deformation lines in cold-rolled alpha brass at about 20 pct reduction in thickness using the standard ammonium hydroxide hydrogen peroxide etchant. Price and Davidson4 noted defor- mation lines in common high brass after 26.5 pct reduction by cold rolling using the same etchant. Johnson6 observed dark thick forklike lines in 99.99 pct pure copper reduced 31.8 pct. Adcock6 observed deformation lines in 80-20 copper-nickel alloy rolled 50 pct. Samans7 found no deformation lines in alpha brass single crystals cold rolled 9.5 pct but they did appear after 25 pct reduction using ammonium hydroxide and hydrogen peroxide etchant. Barrett and Levenson8 observed deformation bands in drawn polycrystalline iron at very small reductions in area and noted that their initial appearance perhaps depends on grain size and other conditions. They reported deformation bands in a single crystal of iron reduced 6 pct by drawing. Brickg noted that deformation lines in 70-30 brass apparently associated with I I I I ) planes appeared after reductions of from 20-50 pct by cold rolling. Brick and Williamson10 noted that in single crystals of 70-30 alpha brass "as in polycrystalline brass, no deformation markings appeared until reductions exceeded 20 pct." Cook and Richards" reported that in Copper cold rolled less than about 50 Pet few strain markings were apparent but for higher reductions many strain markings appeared transverse to the rolled direction. In a review article Brick and Phillips12 noted that previous studies had not shown deformation lines in cold rolled alpha brass below 20 pet reduction and added that 4

Jan 1, 1949

By H. P. Moore, R. W. Fenn, Harold Margolin, W. R. Hibbard

Deformation lines, also called etch markings or strain markings, are non-effaceable lines developed in individual grains by etching a metal specimen which has been cold worked sufficiently to cause atomic non-conformity or slight orientation differences within the grains. Etching occurs more rapidly at these lines of high chemical reactivity to produce a result similar to that revealing grain boundaries. Wider etching effects forming bands have been found. They are believed to be bands of deformation lines which form areas of measurably different orientation from the crystal matrix. The crystallite rotations causing these bands have been shown by Barrett2 to contribute to deformation textures. Although deformation lines have been observed in many metals, the amount of deformation requireti for their appearance has been established only in general terms. Mathewson and Phillips3 observed the first appearance of deformation lines in cold-rolled alpha brass at about 20 pct reduction in thickness using the standard ammonium hydroxide hydrogen peroxide etchant. Price and Davidson4 noted defor- mation lines in common high brass after 26.5 pct reduction by cold rolling using the same etchant. Johnson6 observed dark thick forklike lines in 99.99 pct pure copper reduced 31.8 pct. Adcock6 observed deformation lines in 80-20 copper-nickel alloy rolled 50 pct. Samans7 found no deformation lines in alpha brass single crystals cold rolled 9.5 pct but they did appear after 25 pct reduction using ammonium hydroxide and hydrogen peroxide etchant. Barrett and Levenson8 observed deformation bands in drawn polycrystalline iron at very small reductions in area and noted that their initial appearance perhaps depends on grain size and other conditions. They reported deformation bands in a single crystal of iron reduced 6 pct by drawing. Brickg noted that deformation lines in 70-30 brass apparently associated with I I I I ) planes appeared after reductions of from 20-50 pct by cold rolling. Brick and Williamson10 noted that in single crystals of 70-30 alpha brass "as in polycrystalline brass, no deformation markings appeared until reductions exceeded 20 pct." Cook and Richards" reported that in Copper cold rolled less than about 50 Pet few strain markings were apparent but for higher reductions many strain markings appeared transverse to the rolled direction. In a review article Brick and Phillips12 noted that previous studies had not shown deformation lines in cold rolled alpha brass below 20 pet reduction and added that 4

Jan 1, 1949

By Stanley D. Michaelson, Norman Weiss

This was a year of realization. Some years are for planning and development, some for designing and building, others for fulfillment. With greater hopes and plans for the future than ever before, the year 1954, nevertheless, will be remembered principally because of project completion. Among copper mines, for example, there were Silver Bell, Copper Cities, Bisbee, Yerington, and White Pine. In iron, there were the Humboldt, Coleraine, Cerro Bolivar, and Eagle Mountain. In asbestos, Johns-Manville's new mill at Asbestos, Que. In uranium, completion of the ninth mill on the Colorado Plateau-Kerr-McGee's at Shiprock, N. M. In research, 1954 marked the completion of Kennecott's Research Center in Salt Lake City, one of the historic forward strides in the science of minerals beneficiation. The year was fruitful in other directions as well. Investigations of a fundamental nature were on the upswing, and pilot plant projects have also increased in size and number. Progress in new reagents and equipment was greater than normal. It can already be conservatively predicted-from the technological point of view-that 1955 and 1956 will be tremendous years.

Jan 3, 1955

By N. Tiner

The mechanical properties of magnesium-alloy castings are greatly improved by grain refinement, and at present considerable attention is being paid to methods of obtaining fine-grained castings. One method of achieving this end is the use of proper melting and superheating techniques. These have been employed com-rnercially to a great extent, but no comprehensive study of the subject appears to have been published at present. Numerous investigations found in the literature include some reference to superheating techniques,1"4 and Achenbach, Nippcr and Piwowarsky,% ased principally on thermal analysis, ascribe the grain-refilling action of superheating to the influence of solid foreign particles or dissolved gases present in the melt upon the course of crystallization. The primary purpose of this paper is to present the principal facts concerning the cffect of superheating on grain size of magilesium alloys. .ittempts are also made to explain the experimental results in terms of a general hypothesis. The investigations are limited chiefly to common commercial casting alloys. In order to carry on this work, it was necessary to determine the factors influencing grain size and to develop a proper technique for the preparation of samples. Thc preliminary tests made by the author indicated that the grain size of magnesium alloys resulting from the solidification of a melt is determined by alloy composition, presence of impurities, rate of cooling during solidification, thermal history of the melt and to some extent the structure of the charge used. The rate of cooling is in turn dependent upon the mass of the melt, pouring temperature, and dimensions, properties and temperature of the mold into which the melt is poured. The final grain size of the alloys is still further modified by heat-treatment subsequent to casting. It is not within the scope of the present paper to discuss all of these factors, and it would suffice to note here that when equal amounts of magnesium alloys are prepared from the same alloying materials, melted in graphite crucibles under the same thermal conditions, then cast into graphite molds at a constant temperature, the resultant solids have the same grain size. By maintaining all other factors constant, it is thus possible to vary thermal conditions of a melt and to examine the grain size of resultant castings. Preparation of Samples and Grain-size TestiNg The alloys investigated in this paper were taken from ingots made by Permanente the Or or prepared by the author with pure carbothermic magnesium and necessary alloying elements. Melting was carried out under a flux in a graphite crucible heated uniformly by an

Jan 1, 1946

By N. Tiner

The mechanical properties of magnesium-alloy castings are greatly improved by grain refinement, and at present considerable attention is being paid to methods of obtaining fine-grained castings. One method of achieving this end is the use of proper melting and superheating techniques. These have been employed com-rnercially to a great extent, but no comprehensive study of the subject appears to have been published at present. Numerous investigations found in the literature include some reference to superheating techniques,1"4 and Achenbach, Nippcr and Piwowarsky,% ased principally on thermal analysis, ascribe the grain-refilling action of superheating to the influence of solid foreign particles or dissolved gases present in the melt upon the course of crystallization. The primary purpose of this paper is to present the principal facts concerning the cffect of superheating on grain size of magilesium alloys. .ittempts are also made to explain the experimental results in terms of a general hypothesis. The investigations are limited chiefly to common commercial casting alloys. In order to carry on this work, it was necessary to determine the factors influencing grain size and to develop a proper technique for the preparation of samples. Thc preliminary tests made by the author indicated that the grain size of magnesium alloys resulting from the solidification of a melt is determined by alloy composition, presence of impurities, rate of cooling during solidification, thermal history of the melt and to some extent the structure of the charge used. The rate of cooling is in turn dependent upon the mass of the melt, pouring temperature, and dimensions, properties and temperature of the mold into which the melt is poured. The final grain size of the alloys is still further modified by heat-treatment subsequent to casting. It is not within the scope of the present paper to discuss all of these factors, and it would suffice to note here that when equal amounts of magnesium alloys are prepared from the same alloying materials, melted in graphite crucibles under the same thermal conditions, then cast into graphite molds at a constant temperature, the resultant solids have the same grain size. By maintaining all other factors constant, it is thus possible to vary thermal conditions of a melt and to examine the grain size of resultant castings. Preparation of Samples and Grain-size TestiNg The alloys investigated in this paper were taken from ingots made by Permanente the Or or prepared by the author with pure carbothermic magnesium and necessary alloying elements. Melting was carried out under a flux in a graphite crucible heated uniformly by an

Jan 1, 1946

By Chas. A. Ashburner

The occurrence of oil- and gas-springs in the State of New York has been a fact of historical record since 1627, when the existence of the Cuba oil-spring was first recorded. The utilization of natural gas at Fredonia in 1821 attracted the attention of the public to the possibility of obtaining an illuminating gas by digging and drilling into the rocks. No active search was made, however, for oil or gas by the drilling of wells until after the discovery of commercial oil in Pennsylvania in 1859. In 1862 a well was drilled at Bradford, McKean County, Pennsylvania, but a few miles south of the New York state line, to the depth of 200 feet, in search of the oil-sand which had been found at Titusville, Oil City, and at other points in Western Pennsylvania. Immediately subsequent to this, other wells were drilled in search

Jan 1, 1888

By E. M. Murphy

(Presented by invitation at a meeting of the Spokane Local Section of the Institute, Feb. 17, 1912.) EIGHT years ago the Hecla mine, a lead-silver producer, situated at Burke, Idaho, was producing ore from but two levels, the 300- and the 600-ft. All hoisting was done with a 12- by 16-in. slide-valve, double-reel, hoist. The hoist was being worked to its capacity and was unsuitable for hoisting from greater depths. As the work of opening a new level was about to be started, it became necessary to remodel the then-existing equipment or install a new hoist. The recent advent of electricity from Spokane had made available a cheaper power than steam. By a series of tests conducted throughout the Coeur d'Alène district, it was found that it cost $109 per year to generate a horse-power with steam. Electric power was to be had for $50 a horse-power per year. It was decided to substitute for the engines a motor-drive, of sufficient capacity to operate from the 900-ft. level, and ultimately install an entirely new hoist. After disconnecting the engines, installing a new shaft, and making a few minor changes, a 300-h-p., 2,300-volt, 514-rev. per min., variable-speed motor of the induction type was geared to the reel-shaft. The reels were supplied with 3/8 by 4-in. flat rope, and the duty of the hoist was about as follows: Cage, 1,700; ore, 2,600; car, 1,400; rope, 2,250; total, 7,950 pounds. The Bristol ammeter chart, Fig. 1, shows the combined current-consumption of the hoist- and mine-motors. The large intermittent load is clearly shown ; this produced harmful fluctuations in the voltage of the long, lightly-loaded, 60,000-volt transmission-line from Spokane to the Coeur d'Alènes. The power company received no compensation for the increased cost of producing power for this intermittent or fluctuating load. In order to protect its system from similar excessive

Sep 1, 1912

By M. von Heimendahl, G. Thomas

The microstructure of TD-Ni has been examined by transmission electron microscopy in the extruded, annealed. and deformed states. The tensile properties hove been correlated with the observed microstructures and the results ore com-pared with those obtained from pure nickel. The important conclusions are that the thorin particles in TD-Ni act as strong burriers to dislocntion motion during both deformation (slip) and annealing (climb). During deformation. the dislocations tangle around the particles and a cell structure is devleloped after 10 pct or more strain. The cell size appears to be determined by the spacing of the largest particles and is about five times smaller than that in pure nickel for the same strain. The higher work-hardening rate in TD-Ni compared to nickel is probably due to the more rapid rate of dislocation multiplication in the alloy as a result of dislocation-particle interactions. The Th0,particles inhibit recrystallization and twin growh so that some strengthening may arise from the high density of small annealing twins. THE strengthening of materials due to the presence of a dispersed second phase has been the subject of considerable experimental and theoretical investigation in recent years. One of the newest dispersion-strengthened alloys to be developed is TD-Ni,1 a system of approximately 2 vol pct thoria (ThO2) dispersed in a matrix of commercially pure nickel. This material is fabricated by powder-metallurgical techniques and offers high-temperature stability and useful mechanical properties virtually to the melting point of the base metal. While the mechanical properties of this system have been investigated,2,3 there have been no reports in the literature concerning the microstruc-ture of TD-Ni and its correlation to mechanical properties. This paper describes a transmission electron microscopy investigation of the micro-structure of TD-Ni together with its mechanical properties. The results are compared with the structure and properties of pure nickel.

Jan 1, 1964

By Robert H. Hafner, Irvin R. Kramer

IN recent years considerable interest has been shown in surface-alloyed metals, particularly those of chromium (chromized steels), which have excellent corrosion [ ] resistance under a variety of severe conditions, and may undergo bending and flanging operations without spalling. An early method1 employed to produce a high-chromium case on steel was developed by Kelley in 1921. It consisted of heating a low-carbon steel in intimate contact with powdered chromium in the presence of hydrogen at temperatures sufficiently high to permit diffusion of chromium into the steel. The usefulness of this process was limited because the extremely high temperatures of 1200° to 1400°C. (2200° to 2550°°F,) caused excessive grain growth and warpage, Louenstein and Ulmer2 packed iron castings in ferrochromium and com- [ ] mon salt, and heated for approximately three hours at 930° to 1040°C. (1700° to 1900°F,). A recent and more practical method of depositing chromium on steel surfaces has been developed in Germany by Daeves, Becker and Steinberg3-8 and in Russia by Izgaryshev and Sarkisov.9 This process consists of passing gaseous chromium chloride over the steel to be chromized at temperatures of 900° to 1000°C., or packing them in a porous, ceramic material that previously had been saturated with chromium chloride. They reported obtaining a chromized layer, 0.004 in, thick, on low-carbon steels. Later, Daeves4 established a relationship between the carbon content

Jan 1, 1942

By H. Kurushima, S. Tsunoda

An investigation of the hydrometallurgy of Cu-Zn concentrates by The Dowa Mining Co. of Japan is described and a detailed flowsheet of the Kosaka hydro-metallurgical plant is given. Sufficient operating experience has shown that the Dorrco FluoSolids system has proven successful for recovery of both zinc and copper by roasting in a fluidized bed. At present, 2400 metric tons of concentrates per month are being treated and recoveries of 93 pct Cu and 65 pct Zn are being effected. A SURVEY of the Japanese chemical industry in 1949 revealed, among other things, that sulphur-bearing blast furnace gas from the Kosaka smelter of The Dowa Mining Co. Ltd., Kosaka, Japan, was being exhausted to the atmosphere as waste. In addition, it was costing that company an average of ten million yen ($28,000) annually for damages to the surrounding property caused by the sulphur dioxide in the gas. It was recommended by this survey that the gas be utilized for the production of sulphuric acid by the contact process. Mr. Kurushima visited the United States in May 1950 to investigate the engineering, construction, and operation of a contact acid plant. Any acid produced at Kosaka would necessarily have to be 98 pct H,SO, to prevent corrosion in railroad tank cars transporting it to the point of use. However, the production of 98 pct acid requires constant volume and SO, content of the gas. As the converter gas at Kosaka fluctuates in both volume and quality, it was decided to evaluate the smelting process with relation to other methods of recovery. This evaluation revealed a relatively new type of roaster, the Dorrco FluoSolids reactor, which was reported to be capable of roasting the copper sulphide concentrate in an excess of air with the production of an SO1 gas strong enough for acid production and a water-soluble copper sulphate calcine. The copper sulphate then could be leached from the roasted ore and electrolytic copper recovered from the leach solution in much the same manner as practiced by the Chile Exploration CO. for treating naturally occuring copper sulphate ores. Use of a reactor of this type would eliminate the need for a blast furnace and converter and, in addition, would effect savings in labor and fuel. The Kosaka ore is a microscopically fine mixture of copper, zinc, and lead sulphides. The lead and a small amount of the barite present can be separated by flotation, but any separation of copper and zinc proved extremely difficult. In blast furnace operation at Kosaka, zinc had been slagged off until a stockpile of about 12,000,000 tons containing 5 pct Zn had been accumulated. Mr. Kurushima felt that if any of the zinc in the concentrate was sulphat-ized and leached with the copper, it also could be recovered electrolytically. The Dorr Co., sponsors of fluidization technique in the metallurgical field, suggested that sulphate roasting be tested out on a laboratory scale and that, if successful, a commercial Dorrco FluoSolids system be constructed. They indicated that the results from such laboratory tests could be transposed to a commercial scale without pilot planting the roasting operation. It was therefore decided to send samples of flotation concentrate to the West-port Mill, laboratories of The Dorr Co., for testing. The objective of Mr. Kurushima's visit to the United States thus had changed from investigation of sulphuric acid plants to a fundamental examination of the hydrometallurgy of copper and zinc. Testing Program In February 1951, Mr. Tsunoda went to the United States to witness the application of the FluoSolids system to sulphate roasting at The Dorr

Jan 1, 1956

By N. N. Breyer, W. R. Warke, S. Dinda

A model for the low-temperature peak, LTP, in fcc metals is presented. In high stacking fault energy metals, e.g., aluminum and nickel, it is proposed that a reversible dislocation glide and climb process might give rise to the observed high relaxation strengths and activation energies equivalent to volume self-diffusion values. In low stacking fault energy metals such as copper, gold, and silver, dislocation climb is energetically unfavorable at T < 0.5 Tm and the relaxation process is therefore mainly one of reversible glide. This model is used to explain the effect of a change in grain size and impurities on the LTP. THE low-temperature grain boundary damping peak, LTP, in spectroscopically pure aluminum,&apos; copper,17&apos; gold,2 nickel,3 and silver4 has recently been the subject of a detailed investigation by our laboratory. The main results are summarized in Table I. An empirical relationship was found between the peak relaxation strength, AE, and the width of the dissociated dislocation, do,* given by: do = µa2/24p? (Ref. 5) [I] where p is the shear modulus, y is the stacking fault energy,6-8 and a is the lattice parameter, Table 11. 4E is plotted against do in Fig. 1. Two regions are apparent: region (a)! which contains all but one of the metals, where AE decreases linearly with increasing do, i.e,, AE 1/do; and region (b), where ?E is approximately independent of do. A similar trend is observed when the ratio Qp/QL is plotted as a function of do, Fig. 2. (Qp and Ql are the activation energies for the peak and for lattice diffusion, respectively). In the past, when Qp and QL were found to be comparable, the relaxation peak was explained in terms of grain boundary sliding.10 The equivalence of Q, and Qb. the activation energy for grain boundary diffusion, prompted the suggestion that it was a consequence of reversible grain boundary migration on an atomic scale." A new model for the LTP, which is based on the experimental relationships in Figs. 1 and 2, is presented. In region (a) it is suggested that stress relaxation occurs through the reversible glide and climb of grain boundary dislocations; in region (b) only reversible glide can take place. The resultant effect on the grain boundary might be sliding or "a bowing out", but, since the total distance moved will be 50A, the atomic movements are considered of primary im- portance. It must be emphasized that this is only a qualitative model, but at the moment it appears the most likely way to explain the widely varying, but re-

Jan 1, 1969

By C. J. Fleisch, C. P. Clingerman

THE recent installation of a combination dust catcher, gas washer and precipitator at Carrie blast furnaces of the Homestead Steel Works has given very satisfactory results. The following description of the gas-cleaning installation is based on actual operating experience. When Carrie blast furnace No. 3 was rebuilt the decision was made to fine-clean all the gas produced by the furnace, because the management wanted fine-cleaned gas for fuel in the stoves and boilers. In order to keep the installation cost as low as possible, the gas-cleaning system was streamlined. All by-pass lines and goggle valves for bypass lines were eliminated from the system. A radical departure from the use of 8-in. tubes in the Cottrell-type precipitators was made by using 12-in. diameter tubes in a single compartment, the single compartment being divided into two units by a single partition wall in the top header. THE FURNACE PROPER A few of the characteristic points and dimensions of the furnace proper are: [Hearth diameter 26 ft. o in. Bosh diameter 29 ft. 1 3/4 in. Stock-line diameter 20 ft. o in. Large-bell diameter 114 ft. 8 in. Small-bell diameter 6 ft. 6 in. Height of furnace from center of iron notch to bottom of large bell, closed 94 ft. 4 in. Height of furnace from center of iron notch to main platform 105 ft. o in.] The furnace top is equipped with a McKee revolving distributor, the operation of which is electrically interlocked with the skips, bell hoists, and coke-weighing and charging apparatus through a Freyn automatic charging control. The gas leaves the furnace first through four offtakes, 5 ft. g in. in diameter, then through uptakes that are approximately 85 ft. high, which feed into a single down-comer that is 9 ft. in diameter. DUST CATCHER The primary dust catcher installed (Fig. I) may be described as a single-cone type. The inlet pipe at the top of the dust catcher is g ft. in diameter; it is flared to a conical shape as it extends down inside the dust-catcher shell, which is 35 ft. in diameter, 37 ft. high on the straight side, and has a conical top and bottom. The slope of the bottom is 50° with the horizontal. The cone-shaped pipe inside the dust-catcher shell is 42 ft. high and is 19 ft. 7 in. in diameter at its bottom lip where it releases the gas in-

Jan 1, 1943

By Robert W. Hunt

The memorable features of American history have been making fast during the last century, and notably so since 1860; and they are by no means confined to political or to any one branch of scientific development. Of all the industrial arts, none show a greater change or &apos;a mightier progress than the Bessemer manufacture. And this year, while we are celebrating the first centennial of our national life, we can also celebrate the first decennial of American Bessemer practice. While not forgetting or undervaluing what has been done in other countries, I have thought that a brief history of the introduction and development of the Pneumatic or Bessemer process in America would be of interest. In 1863 the Kelly Pneumatic Process Company was formed and an arrangement entered into with William Kelly, who had taken out letters-patent of the United States, Nos. 16,444; 17,628, reissued as 505; 18,910, dated January loth, 1857; June 23d, 1857; November 36, 1857; and December 22d, 1867, respectively. This association mas composed of the Cambria Iron Company, E. B. Ward, Park Brothers & Co., Lyon, Shorb & Co., Z. S. Durfee, and, later, Chouteau, Harrison & Valle joined the combination. Not satisfied with possessing the control of the Kelly patent, they sent Mr. 2. S. Durfee to England, to secure for this country Mushet&apos;s patent on recarburization, No. 17,389, dated May 26th, 1857, the same having been taken out in England on September 22d, 1856. In this Mr. Durfee was successful. Previous to the application of William Kelly for a patent, Henry Bessemer, of England, had taken out patents dated February 12th, 1856, and August 25th, 1856, in this country. Kelly claimed priority in the discovery of the principles of the process, and the Patent-office allowed his claim by granting him his patents. In the autumn of 1862 Mr. Alexander L. Holley, while in England, was impressed with the importance of Mr. Bessemer&apos;s invention, and so fully foresaw its future, that, upon his return to the United States, he induced Messrs. John A. Griswold and John F. Winslow, of Troy, New York, to join him in endeavoring to possess Bessemer&apos;s American patents. Mr. Holley returned to England in

Prof. J. C. BRanner, Stanford University, Cal. (communication to the Secretary): On p. 398, Mr. Hedburg mentions Marionite and Brannerite as ores of zinc. Neither of these has been authoritatively recognized as a distinct mineral species. Marionite, originally described by Elderhorst, was subsequently determined to be nothing else than hydrozincite. Analyses of the so-called Brannerite were sent by me to Prof. Penfield, who says it is a mixture of Smithsonite with some other mineral. On p. 398, Mr. Hedburg says the zinc-bearing formation of North Arkansas " is recognized as the Upper Silurian." So far as my observation goes, the ores occur both in Lower Carboniferous and in Ordovician or Lower Silurian rocks, but nowhere in rocks known to be of Upper Silurian age. If Mr. Hedburg has any paleontological evidence of the Upper Silurian age of these rocks, or of any of them, he will confer a favor upon geologists by making it known. On the same page is another statement in which I cannot concur. He says that in this region, " it can easily be seen that the largest fissure-deposits have been eroded and washed away, leaving here and there a few patches adhering to the hillsides." I am compelled to say that in many years&apos; study of the geology of the region in question, I have never been able to recognize such a state of affairs as Mr. Hedburg here describes. The patches which he regards as remnants of fissure-veins, " adhering to the hillsides," I have found to be either the edges of bedded deposits, or portions of the zinc-bearing breccias, formed along old drainage-lines, and laid bare by the ordinary processes of erosion. That fissure-deposits have been partly removed by the same agency, goes without saying; but it is, in ,my judgment, no more true of North Arkansas than of any other mining-region that erosion has selected and washed away " the largest " deposits. My own views of the region in question are given in detail

Jan 1, 1902

By C. R. Fast

In order to evaluate the ability of a Hydrafrac treatment to effect a sustained increase in well production, data were accumulated on the first 65 wells in 26 fields treated by Stano-lind. Since these data were obtained from such a large number of fields, it is felt that individual well or reservoir characteristics do not affect the overall picture, as might be the case if the study were made in one field or one group of wells in a field. These data are tabulated in Table I and plotted on Figs. 1 and 2. An analysis of Fig. 1 shows that at the end of six months, 75 per cent, or 45, of 60 wells on which data were available showed a sustained production increase. At the end of two years, data were available on 25 wells. Of these, 15 wells, or 60 per cent, showed a sustained production increase. At the end of three years, 55 per cent, or 10, of 18 wells had a production rate greater at that time than before Hydrafrac treatment. The lack of information on additional wells at the end of the third year is primarily a result of the small number of treatments conducted in the early stages of field application

Jan 1, 1952

COLUMBIA SECTION STANLY A. EASTON, Chairman, FREDERIC KEFFER, Vice-Chairman, L. K. ARMSTRONG, Secretary-Treasurer, P. 0. Drawer 2154, Spokane, Wash. D. C. LIVINGSTON FRANK A. Ross The first meeting of the Columbia Section was held on March 24, as a part of the 1916 Northwest Mining Convention which was held under the -auspices of the Spokane Mining Men&apos;s Club assisted by the Spokane Chamber of Commerce, the technical program being in charge of the Spokane Engineering and Technical Association assisted by the local sections of the A. I. E. E., A. S. C. E., and A. I. M. E. The program of the successive sessions was carefully arranged with view to its application to mining, and in addition to the technical program there were exhibits of ores, minerals, devices, etc., of interest to the delegates, who numbered over 500. A portion of the program was also arranged with special reference to the requirements of the prospector and miner. A reception, a banquet, a complimentary luncheon, a regular daily call&apos; of the Stock Exchange, a visit to the High Schools and to one of the substations of the Washington Water Power Company and to the Union Iron Works kept the visitors entertained, the ladies being looked after by a special committee of ladies who held open house during the entire week. Several important resolutions were passed by the Convention and one by the Columbia Section, A. 1. M. E. With Stanly A. Easton, chairman, presiding, the Columbia Section, American Institute of Mining Engineers, occupied the time between 2.00 and 5.30 p.m., March 24th, the Moorish room of the Spokane hotel being filled with members and their guests. "The Apex Law and the Mineral Surveyor" was a paper presented by F. W. Callaway and generally dis-cussed because of its local application in the Coeur d&apos;Alenes, the conclusions being reached after expensive litigation between two of the large mining operators in that district.

Jan 6, 1916