Search Documents

By Kalanadh V. S. Sastry, D. W. Fuerstenau

A locked-cycle balling procedure has been designed to simulate continuous, closed- circuit balling drum operation in the laboratory. By this method, it is possible to simulate the surging in green-ball production rate and circulating load that is experienced in industrial balling circuits. Through an investigation of the effect of feed rate on the stability of the locked-cycle, balling process, it was found that higher feed rates lead to increasing instability in the process. An analysis of the experimental ,results is presented and the utility of the locked-cycle experimental technique for evaluating the stability of an industrial balling drum operation is discussed.

Jan 1, 1976

By John B. Pearse

The works heretofore used in carrying out the Bessemer process have been constructed substantially as follows: The whole works or plant has been divided into three parts. 1. The division in which the metals for conversion are melted. 2. The division in which the metals are converted into steel and cast into ingots, or the converting department. 3. The engine and boiler department which supplies the hydraulic power required to move the machinery, and which furnishes the blast used for converting the crude metal into steel.

By M. L. Jeremic

Abstract-Observations of ground behavior in mining the Choka Dulkan ore body have been described. Ore recovery was limited to approximately 60% because unconsolidated hydraulic fill did not permit either the widening of stope spans nor secondary ore recovery from pillars. Stope undercutting induced high stress concentrations. However, as extraction progressed, ground conditions improved but before extraction was complete they deteriorated again. After completion of a stope, the remnant rib and crown pillars continued to be deformed by other stresses for some time.

Jan 4, 1978

By W. R. Phibbs

THE blast furnace of the Columbia Steel Corpn., at Ironton; Utah, was put in blast April 30, 1924, and its operation has presented some interesting problems. The coke for the furnace is furnished by 33 Koppers Becker type ovens of 15 tons capacity each. The coal is shipped from the company's mine at Columbia, Utah, which is approximately 123 miles from Ironton, and is probably the highest volatile coal that is being coked for blast furnace use in this country. The analysis of the coal is: PER CENT. Moisture 3.90 Volatile 39.00 Fixed carbon 51.10 Ash.... 6.00 Sulfur : 1.07 The analysis of the coke is: PER CENT. Volatile 0.55 Fixed carbon :...:.::: :..:.:: 89.70 Ash 9.75 Sulfur 1.05

Jan 1, 1928

By D. H. Davis

There are two general types of oil flotation processes, froth and bulk-oil. In froth flotation, the coal concentrates are removed in the form of a froth or foam composed of air, liquid, and solids. Mechanical or pneumatic agitation of a coal slurry with suitable frothing agent causes a selective action of the bubbles to the coal particles which are carried to the upper portion of the pulp in the flotation cell; the refuse is wetted by the water and does not rise with the froth, but goes out as tailings. The other type of flotation process, bulk-oil, consists of thoroughly mixing the slurry or pulp with 30 to 50 pct of its weight of oil. The coal agglomerates with the oil and drops to the bottom of the cell while the refuse is wetted by the water and is carried away in suspension. The concentrate granules may be screened and drained to 12 to 15 pct moisture. The minus 200 or 300-mesh is very effectively treated by this process. The Trent process is a bulk-oil type which has been used for coal cleaning on a commercial basis, but its use has been discontinued in this country. Froth flotation of bituminous coal should be subdivided into two distinct fields: (I) separation of a dry coal product such as recovered from an aspiration system; (2) separation of a minus 48-mesh slurry such as produced from a thickener in a wet cleaning plant. The capacities, performance, and general operating characteristics are very different in these two fields. The recirculated slurry in a washery becomes oxidized and is much harder to treat than a dry dust. It is difficult to clean a slurry containing an appreciable percentage of plus 48-mesh without also floating some high-ash clays minus 200-niesh in size. On the other hand, while working with an aspirated dust, good results have been obtained in floating coal as coarse as 3/16-in. Because of the relatively low capacity of flotation machines as compared with conventional fine-coal cleaners .and because of the greater quantity of reagents required to float coarse coal, there is usually no point in considering flotation on bituminous coal for anything coarser than approximately 48-mesh. In some coal-cleaning plants, good separations are being made down to 80 or even 100-mesh by a less expensive system of coal cleaning than flotation. The Pittsburgh Coal Co. carried out extensive tests on laboratory batch machines and on small units of both pneumatic and mechanical agitation types from 1930 to 1935 and have operated six, eight, and then twelve mill-size mechanical subaeration cells from 1932 to 1944 This paper will deal with some of the operating phases and results of coal-flotation practices as derived from this experience, and more specifically with the flotation practice at the Champion No. I preparation plant. The experience gained from the research and initial experimental work contributed greatly to the successful operation of the mill-sized flotation units at Champion.

Jan 1, 1949

By Louis A. Panek

Most roof bolts are used in mines with bedded roofs, but it has not been determined to what degree thin-bedded roofs can be reinforced by bolting if there is no thick member in which to anchor the bolts, or what function the bolts must perform in such a case. Owing to widespread practice of systematic bolting to support thin-bedded roofs, moreover, it is desirable to design roof-bolting systems on a quantitative basis. Specifically, a solution to the following problem is required: For a roof composed of beds of given thickness and physical properties, what is the optimum length, spacing, orientation, and tightness of bolts consistent with safety and economy? The investigation reviewed here has produced a functional equation to evaluate these variables and establish basic principles of roof bolting.

Oct 1, 1955

IN NOVEMBER 1933 I had the pleasure of receiving an autographed copy of a small brochure entitled "Birth of the Porphyry Coppers." The author, James Colquhoun, a distinguished British mining engineer, had been the dominant figure in the Arizona Copper Company, Limited, which, until its acquisition by the Phelps Dodge Corporation in 1921, had been the principal producer of copper in the Morenci district. In addition to the highly productive Humboldt and Longfellow mines it owned the Clay property, which, of course, has now become Arizona's No. 1 copper mine. Except for Utah Copper it is the premier Porphyry copper enterprise in the United States. Mr. Colquhoun's little volume was inspired by THE PORPHYRY COPPERS which had appeared early that year. In a most courteous and friendly way he adduces data to show that "we (Arizona Copper Company Limited) were successfully treating low-grade porphyry ores in quantity for at least four years (1901 to 19W) before the Utah Copper Company did anything at all." This last remark is based on the figures in THE PORPHYRY COPPERS showing that Utah's first production came from the Copperton pilot plant in 1905. Mr. Colquhoun traces the story of Morenci beginning in 1883 when he first arrived there. He tells how the rich self-fluxing ores (containing lime- stone, silica, and iron in proportion to permit direct smelting to produce black copper) were gradually exhausted. High-grade siliceous ore could be mixed in limited quantity with the self-fluxing ores; and oxidized ores were leached to contribute substantially to the production of the district. But

Jan 1, 1957

By Ralph V. Higgins

This paper concerns the magnitude of the amount of supersaturation that occurs in an underground reservoir during the flow of oil and gas to wells and to the amount of undersaturation that occurs during repres-suring of an oil reservoir where some effective permeability to gas exists. The study is based on earlier laboratory findings of other investigators on the rate of diffusion of gas in oil as a function of the depth of oil. Utilizing these relationships and the principles of reservoir mechanics, a quantitative estimate of undersaturation and super-saturation was calculated. The results showed that the diffusion of the gas is rapid enough that for all practical purposes no supersaturation exists during the flow of oil to wells or undersaturation during repressuring in reservoir sands having some effective permeability to gas. The reason diffusion of the gas virtually keeps the oil saturated is the long time required in radial flow for oil to reach the well and the slow rate at which pressure in reservoirs is increased during repressuring. INTRODUCTION Knowledge of the phase relationships during flow of gas and oil in an underground reservoir is essential to operating the reservoir in the most efficient manner. In material-balance calculations and in fluid-flow studies, the oil is assumed to contain all the gas that it will dissolve at given temperature and pressure. Pressure-volume-temperature relationships are normally obtained in the laboratory using "bottom-hole" or combined samples of the reservoir fluids. In such laboratory determinations equilibrium is obtained between the oil and gas in the pressure cells by mechanical agitation. During the flow of oil and gas in reservoirs, however, no comparable agitation occurs to mix thoroughly these fluids to aid in effecting equilibrium between the two phases. During repressuring of a partly depleted underground reservoir, the gas is usually injected into the reservoir faster than the oil can absorb it; consequently, the oil is undersaturated. On the other hand, as the oil flows through the reservoir to the wells during producing operations the pressure decreases faster than the gas in solution can diffuse through the oil to the gas phase. The oil therefore is supersaturated with gas. Where the oil is undersaturated, gas diffuses away from the gas-oil interface, and where it is supersaturated the gas diffuses toward the interface. In either case the gas moves from a higher to a lower saturation. This report contains the results of a study of the factors influencing the degree of nonequilibrium of the phase relations of oil and gas in porous mediums during the flow of oil through reservoirs to wells and also during the injection of gas into partially depleted sands. Data from an underground reservoir are presented and the degree of supersaturation during the flow of the oil through the reservoir to the well is approximated. Also data from another reservoir are used and the degree of undersaturation during the repressuring operation is calculated. In addition, the flow rates of oil in laboratory experiments and in underground reservoirs are compared, as data from the laboratory are often used to interpret events in the reservoir, and the rates of flow influence appreciably the degree of nonequilibrium. Much of the contents of this report was prepared in 1943; but, because of other activities during and since the war, the manuscript was left untouched until 1952, when it was decided to include an estimate of the amount of undersaturation during repressuring as well as supersaturation during flow.

Jan 1, 1955

By W. N. Marchant, P. T. Brooks, P. B. Altringer, R. O. Dannenberg

The US Department of the Interior, Bureau of Mines conducted laboratory tests to devise a process for recovering a marketable grade of tungsten from the brine of Searles Lake, Calif. The brine contains only 56 ppm W (70 ppm W03). Using ion exchange resins synthesized by USBM chemists, 98% oft he tungsten was extracted from the brine and 92% of the tungsten was recovered as a marketable iron-tungsten concentrate containing 44% tungsten as tungsten trioxide. Although major technical problems have largely been resolved, research is progressing to escalate testing in a process research unit to provide more reliable data for an economic appraisal.

Jan 8, 1979

By Kenneth Robertson

THEREi9 probably less known of this subject than of any other connected with the metallurgy of iron. In all the books that treat of this mattes, there are given analyses of slags, their chemical formulae, the loss of iron, etc. ; but few, if any, give the character of the iron made at the time ; none give analyses and physical characteristics of the ores and limestones used, and they present merely isolated examples from various furnaces, and consequently one is more frequently puzzled than enlightened after reading them. During two years I have had occasion to analyze the slags and many of the pig-irons from two furnaces, and for this article I have made analyses of all the different grades of pig made by them. A

By A. M. Gaudin, D. W. Fuerstenau

IN concentration of certain ores by soap flotation, prevention of quartz flotation is desired; the contrary is true in treatment of some oxide iron ores. Experimental study of the flotation of quartz goes back at least a quarter of a century.' Clean quartz does not float with fatty acids or soaps but does float when activated by one of many metallic salts. Control of pH is important. Broadly speaking the problem of quartz flotation has been approached from the empirical side, as was the related topic of flocculation or dispersion of quartz suspensions.' Empirical studies indicated the existence of critical relationships between the additions of collector and activator. These additions were not stoichiometric for the formation of soaps of the activator cation.

Jan 1, 1955

By W. W. Anderson

A formula for quantitative efficiency is proposed, in which the efficiency value is a function of the improperly distributed material at the gravity of separation effected by the cleaning equipment. The misplaced material is expressed as a percentage of the total material discharged from the equipment. Numerous examples are given, demonstrating application of the formula to various types of separation, including multiple-product separations.

Jan 2, 1950

By R. W. Smashey, B. J. Piearcey

The structure, composition, and morphology of the carbide phases present in the nickel-base superalloy, Mar-M200, hare been determined and three carbide phases observed. The MC carbide is a solidification product, and the M23 Co and M6C carbides are both prod~icts of solid-state precipitation. The identity of each phase usas determined by both X-ray and electron-diffraction techn~ques. Compositions of all three carbides were studied using the electron beam micro-probe analyzer and by unalyszs of electrolytically extracted residues. Optical and electron microscopy were employed in order that the time/temperature -dependent behavior of the carbides might be observed. Supplementary studies were completed on thin foils and oriented single crystals to determine the mor-phology and orientation relationship of each phase with that of the matrix. MAR-M~OO* is a high-temperature, creep-resistant superalloy designed for use in the as-cast condition. The "as-cast" microstructure consists of a solid-solution matrix, referred to as gamma (y), which contains a general, coherent precipitate of the inter-metallic Ni3(A1,Ti) referred to as gamma prime (?). As a result of dendritic segregation during solidification, a degenerate, spherulitic ? -?' eutectic constituent is present at the grain boundaries and the in-terdendritic regions, which is nucleated by the y on the dendrite tips. A primary carbide phase, a solidification product, is also present at the grain boundaries and in the interdendritic areas, and an additional carbide appears at the grain boundaries as a fine discontinuous precipitate. The alloy is particularly susceptible to heat treatment. For example, the mechanical properties of the columnar grained mater- ial are substantially improved by solution heat treatment, followed by an intermediate temperature age. Metallographic examination of heat-treated material reveals, however, that exposure to elevated temperatures has a marked effect on the microstructure of the alloy; in particular, it is observed that precipitation of considerable amounts of various carbide phases occur. The following investigation was carried out to determine the morphology, composition, and behavior of the carbides in Mar-Ma00 as an aid to the determination of their effect on the mechanical properties and stability of the alloy. THE PRIMARY MC CARBIDE The MC carbide phase appears in the interdendritic interstices and the grain boundaries. In directionally solidified Mar-M200 the carbide appears as very small particles in the chilled region, Fig. l(a), whereas in material less affected by the chill, it becomes larger and develops a dendritic morphology, Fig. 1(b). Step polishing of metallographic specimens from this region shows that in directionally solidified material the individual carbide dendrites are connected in a dendritic network within the metallic interdendritic interstices, whereas in material from the chilled region and in conventional Mar-M200 they are discontinuous, isolated dendrites. No orientation relationship exists between the primary carbide and the matrix.

Jan 1, 1968

By W. D. Robertson, R. E. Reed-Hill

Slip on (11221 planes, which do not contain a close-packed direction, has been identified on crystals strained at —190°C. Evidence is also presented to show that (1071) pyramidal slip is a mode of deformation at 25ºC in a limited orientation range. PYRAMIDAL slip (l011) <1120> in magnesium at elevated temperatures has been established for some time.1-2 More recently, Burke and Hibbard reported this mode of deformation at 25ºC, but their results were questioned by Craig.&apos; Also, as far as the present authors know, slip in magnesium on pyramidal planes of the second order, Type II (1122)) has not previously been reported, although Gilman"," identified (1122) slip in another hexagonal metal

Jan 1, 1959

T. M. Morris (Measurement and Evaluation of the Rate of Flotation as a Function of Particle Size, P. 794), was the commanding officer of a patrol craft charged with guarding Aleutian waters against infiltration by the Japanese during World War II. Before going into service, he was an assistant research engineer with Anaconda Copper at Anaconda, Mont., and later a metallurgist with Tennessee Copper Co. Presently he is a professor in the Department of Metallurgy, Missouri School of Mines, Rolla, Mo. A member of the AIME, he is a graduate of Columbia University and the University of Missouri, with a Bachelor of Science, Master of Science and a Ph.D. Professor Morris is the author of a previous paper for the AIME, Measurement of the Equilibrium Forces Between an Air Bubble and an Attached Solid in Water. An outdoor man by predilection, he enjoys bird watching and hiking in his free time.

Jan 1, 1952

By F. I. Stalkup

Vapor-liquid phase equilibrium experiments have been conducted in a static equilibrium cell on mixtures of a light, 45 API stock- tank gravity reservoir fluid and a rich hydrocarbon gas containing approximately 55 mole per cent of intermediate hydrocarbons. Both apressure-vs-composition study of the gas and a simulated reservoir fluid, and a multiple-batch contact simulation of the condensing-gas-drive oil recovery process were performed. In the latter experiments equilibrium gas and liquid compositions were analyzed. Also, conventional, "condensing-gas-drive", long-tube displacement experiments of the reservoir fluid and gases of various richness were performed. The results of these experiments could not be satisfactorily interpreted by the conventional pseudo-ternary-diagram representation of multicom-ponent phase behavior. The results seem to be explained better by considering a bubble-point surface and a dew - point surface joined in a plait-point locus. Portions of the plait-point locus cannot be "seen" directly by the rich hydrocarbon gas because of curvature of the dew-point surface. In such a system, continuous injection of the rich gas over stationary reservoir fluid might form a zone of contiguously miscible compositions from pure rich gas to pure reservoir fluid by: (1) saturating the reservoir fluid with injected gas to the bubble-point surface; (2) creating by mass transfer with fresh injected gas a path of contiguously miscible compositions along the bubble - point surface to the plait-point locus; and (3) creating by mass transfer with additional injected gas a path of gas compositions along the dew-point surface up to the point where direct miscibility results between dew-point fluid and the injected rich gas. INTRODUCTION The use of the pseudo-ternary-phase diagram to illustrate miscible displacement phase behavior has been discussed by several authors.5,7 Such a representation of phase behavior is not rigorous, but the ternary diagram nevertheless gives a qualitative picture of what actually occurs in a miscible displacement process. Fig. 1 is a typical illustration of miscible displacement phase behavior by a ternary diagram. The multicomponent hydrocarbon system is divided into three pseudo-components: a light fraction containing methane and nitrogen, an intermediate fraction containing ethane through hexanes plus carbon dioxide, and a heavy fraction containing heptane and heavier components. A two-phase region is bounded by a dew-point curve and a bubble-point curve, which are joined at the critical point. The concept deduced from such a representation for miscible displacement by a condensing-gas-drive process is as follows: a rich gas G, which lies to the right of the limiting tie line through the critical point C, is injected into the reservoir and contacts reservoir fluid L, saturating the reservoir fluid to give bubble-point fluid L1 and equilibrium dew-point gas GI. Continued injection of rich gas changes the composition of the saturated liquid L1 through a series of liquid compositions lying along the bubble-point curve, until the critical composition C is reached, at which point direct miscibility with the rich gas is achieved. Some equilibrium gas with compositions lying along the dew-point curve from G1 to C is also formed in this process. Thus, continuous injection of rich gas forms a

Jan 1, 1966

By V. Lessels, D. J. Buckwalter, D. H. Rose

At White Pine Copper Co.&apos;s operation in the Upper Peninsula of Michigan, the company has been losing more than four lbs of copper in each ton of sand tailings. With an average rate of 12,000 tpd of sand going to the tailing pond daily, the company has been losing more than 14 million lbs of the red metal annually. With an eye aimed toward lessening this loss, White Pine engineers in 1959 initiated a study on techniques for recovering this "lost" copper from the sands. Inasmuch as the flotation operation was considered to be optimized, a logical approach seemed to be leaching. For various reasons ammonia, ferric chloride, acid, and biological leaching were ruled out as impracticable. This led to a consideration of cyanide leaching as practiced in the precious metals industry.

Jan 8, 1967

By W. F. James, Richard Murphy, S. N. Kesten, A. H. Lang

The paper is a summary of information on Canadian deposits of uranium and thorium up to the end of 1948, prepared by geologists of Eldorado Mining and Refining Ltd. and by the specialist on uranium deposits for the Geological Survey of Canada. The paper contains a history of Canadian uranium and thorium discoveries, a working classification of the deposits, fairly detailed descriptions of the Eldorado mine and of properties in northern Saskatchewan, and shorter accounts of several other discoveries.

Jan 2, 1950

By S. J. Noesen, J. R. Hughes

Several four-inch-diameter tungsten ingots were arc melted in vacuum or in hydrogen atmospheres. Melting pressures, melt-off rates, effect of atmospheres, and other pertinent factors were examined. Two of these ingots were extruded at 1650°C. Subsequently, forging and rolling were carried out at lower temperatures. For a 60 per cent area reduction by rolling, a one-hour recrystallization temperature of 1250°C was obtained. This temperature is considerably lower than those reported in previously published work, and can probably be attributed to the extreme purity of the as-cast ingots (N, H, 0 all less than 1 ppm). EVER since W. D. Coolidge, in 1909, described his process for producing tungsten metal of high density and good workability via the powder metallurgy tech-

Jan 1, 1961

By William E. Ford, Edward Salisbury Dana

THIS Appendix contains a series of tables, more or leas complete, of minerals arranged according to chemical composition or to certain prominent crystallograhic or physical characters. These, it is believed, will be of service not only to the student, but ago to the skilled mineralogist. The type used in the printing of the mineral names indicates their relative importance. Table I is a complete list of the species named in this book arranged fist according to the prominent basic elements which they contain and secondly according to their acid radicals. Table II is of Minerals arranged according to their System of Crystallization The other tablets make no claim to completeness, being limited often to common ah important species. For an exhaustive system of Determinative Tables based particularly upon blowpipe and chemical characters, the student is referred to the work of Professors Brush and Pen- field, mentioned on p. 330.

Jan 1, 1922