Search Documents

By A. R. Troiano, W. J. Barnett

IN recent years the demands of space limitations and increased loads, particularly in the aircraft industry, have accelerated the trend toward utilization of ultra-high strength steels. The increased application of such steels has focused attention on the phenomenon of delayed failure or static fatigue. Parts subjected to a static load, after successfully sustaining the load for an extended period of time, may fail in a brittle manner. Subsequent examination of such failed parts by conventional laboratory tests in many cases reveals no apparent signs of embrittle-ment. That is, the material exhibits good ductility and impact resistance. Furthermore, consideration of the service conditions (environment and temperature) under which this brittle failure occurred eliminates its classification as a stress-corrosion or creep type of failure. Recently this unique time dependent fracture process has been the subject of numerous investigations. The most significant result of these studies was the recognition of hydrogen as the source of embrittlement. While the effect of numerous variables on the occurrence of static fatigue failure has been defined, an adequate explanation of these behaviors is lacking. The occurrence of this phenomenon in steels generally has been limited to strength levels in excess of 180,000 lb per sq in. Although steels at high hardness levels have exhibited delayed failure in the absence of hydrogen introduction after heat treat-ment,'.' this behavior was most prevalent when the material in processing had been subjected to an environment conducive to the absorption of hydrogen. Delayed failures have been produced in high strength steels by the introduction of hydrogen

Jan 1, 1958

By Leendert de Witte

Conventional resistivity logs consisting of a short normal, a long normal, and one or more long lateral curves do not give data that allow a complete quantitative interpretation in beds thinner than 20 ft. Reservoir rocks usually exhibit zones of continuous homogeneity of quite limited thickness where the long lateral curves become useless because of adjacent bed effects and boundary phenomena. If the beds are 12 ft or thicker, the short and long normals may be used for qualitative interpretation, which can be streamlined by the application of simplified departure curves. For beds of a thickness less than twice the long normal spacing, this procedure breaks down. The combination of the limestone curve, the later-olog or guard electrode log, and the microlaterolog permit quantitative interpretation for beds that are at least 10 ft thick, provided the mud resistivity and the hole diameter are known with sufficient accuracy. For beds thinner than 10 ft, combinations of the microlaterolog with short spaced laterologs and pseudo laterologs appear to be promising. Interpretation of these curves again requires the application of simplified departure curves. Resolution of various possible combinations was analyzed using departure curve data calculated on the Whirlwind I computer at the Massachusetts Institute of Technology. A field example is shown using the microlaterolog-microlog combination, and the combination of a 6-in. modified laterolog plus a 6-in. pseudo laterolog. INTRODUCTION For the purpose of quantitative interpretation of resistivity logs in porous formations, we want to obtain two essential quantities from the logs, namely, the true resistivity of the undisturbed formation, Rt, and the resistivity of the part of the formation invaded by mud filtrate, Rt. The apparent resistivities of all conventional logging devices are functions of these two parameters and are also influenced by a third unknown parameter, the diameter of the invaded zone, d. It has been shown' that from the normal curves alone it is impossible to arrive at a unique solution for the three unknowns, Rt, R1, and d1. In very thick homogeneous beds, if invasion is not too deep, we can obtain a fair approximation to Rt from the long lateral curves and then use the two normal curves to find Rt and d1 Even under the most favorable conditions, the resolution of this system is not very good. The short normal does not give a reasonable approximation to R1 unless invasion is very deep (dl>16 hole diameters). For very deep invasion, however, the long laterals no longer approximate Rt. For bed thickness between 20 and 40 ft, the long laterals are affected appreciably by the adjacent beds; and the curves are distorted by boundary anomalies to the extent that they lose their quantitative usefulness in most cases. For the same bed thicknesses, the normal curves still function reasonably well. Although it is impossible to find unique solutions Lor R1 and Rt using the normal curves alone, we can obtain a reasonable approximation for the ratio R1/Rt through the use of simplified departure curves. This fact was brought to our attention by A. J. de Witte, geologist with Continental Oil Co. As the magnitude of Rl/Rt is a major clue to the presence of oil in formations, this method can be used to good advantage for qualitative analysis and will be discussed in somewhat greater detail. With the aid of suitable bed thickness corrections, the analysis of the normal curves may be used for bed thicknesses larger than 12 ft. For thinner beds, the method rapidly loses its resolution; and we have to resort to different types of resistivity logs if we want to attempt to analyze the curves quantitatively. The inadequacy of conventional resistivity curves in thin beds is far more serious than generally realized. Fig. 1 shows a conventional E. S. with a 16-in. and 64-in. normal and a 16-ft lateral through a section of Lansing-Kansas City lime, in comparison to a guard electrode survey through the same section in a neighboring well. The porous zones, which show up as low resistivity breaks on the guard electrode log, are completely masked by adjacent bed effects and boundary anomalies on the conventional curves. Even the short normal shows most of the porous Zones only as Vague deflections and in many cases fails to register Their

Jan 1, 1955

By J. S. Westwater

The Mather mine of The Negaunee Mine Co. embraces nearly all of Sections 1 and 2, T47N, R27W, within the limits of the cities of Negaunee and Ishpeming on the Marquette iron range of Michigan's Upper Peninsula. Operations of the Negaunee Mine Co., the stock of which is jointly owned by Bethlehem Steel Co. and The Cleve-land-Cliffs Iron Co., are under the direction of the latter company. The opening of the Mather mine was described by C. W. Al1en.† Mather " A " shaft was completed to an initial depth of 2352 ft in early 1943. The shaft capacity of over one million tons yearly is in prospect of being realized by orderly development and mining, and sinking of the second or "B" shaft then started in accordance with previous planning. Mather "B," also a vertical shaft, was designed as a twin to Mather "A" shaft and the sinking technique developed at Mather "A" was utilized in "B" shaft operation. Shaft Sinking General Plan An average depth of 16 ft of sand overburden at the shaft site was cleared away by bulldozer, and the shaft approximately 15 by 20 ft in rock opening put down to an initial depth of 87 ft. Mucking of the broken rock to this depth was accomplished by an Insley excavator equipped with a 1/2 yard ca-pacity Owens clamshell bucket. Addition of 200 lb weight to each lip of the clam bucket provided adequate "bite" to dig the broken diorite and jasper rock. Temporary heavy wood bearers were placed across the shaft mouth to support the steel shaft sets which were hung in this initial 87 ft depth, aligned accurately and concreted in place from the lowest set upwards. The permanent steel headframe foundations and three service tunnel openings to the shaft were also concreted in the upper section to the shaft collar. A temporary wood headframe was then erected over the shaft mouth, and initial hoisting machinery assembled consisting of a Lake Shore 12 ft diam single drum grooved for a 1 3/8 in. rope and powered by two 400 hp motors to attain hoisting speed of 1100 fpm. Compressed air was obtained from a Nordberg 2 stage tandem horizontal type with a capacity of 1500 cfm. An enclosed landing platform at the shaft collar was equipped with a rotary dump and pocket for discharge of the rock into a Euclid 15 ton truck. On completing assembly of this equipment and installation of a special cage in the shaft, sinking was resumed on a three shift, six days per week

Jan 1, 1950

By A. F. Andresen

IN the course of another investigation the lattice parameters were determined for a series of compositions of tin in copper. Ten-gram samples of the alloys were made from spectroscopically pure tin and copper. The metals were weighed and placed in graphite capsules (previously fired at 5500°F) which were then sealed individually in evacuated vycor tubes. The tubes were mounted on a spit, transverse to its axis, which continually rotated the melts in a furnace. After homogenizing, filings were made of one third of each slug by filing off a complete cross section. A 325-mesh sieve was used to obtain the powder for the X-ray determination. The sieved powders were annealed in vacuo at 600°C for 24 hr to remove the cold work, and then quenched. The lattice parameters were determined with a flat-plate back-reflection camera using CuKa radiation (A., = 1.5405A, A,? = - 1.5443A). With this radiation the (331) and (420) reflections appeared close to the focusing region. As reference lines were used the same reflections from pure copper powder, between which the (420) lines of all these alloys are situated. The variation of the systematic error over this angular range was found to be less than the estimated experimental error ±0.0005A which is indicated in Fig. 1 for all but the sample with 8 pct Sn. As a check some of the powders also were examined in a regular Debye-Scherrer camera with the Straumanis film mounting. The parameters were here evaluated by extrapolation against cos2? to ?= 90o. The results are shown in Fig. 1 where the lattice parameters in Angstrom units are plotted as a function of weight percent of tin. The reflection lines for the 8 pct alloy were not clear at first, perhaps due to coring. Several measurements were made after different annealing programs on two separate

Jan 1, 1959

By William Meyer

DURING the seventeen years Fairchild has been making aerial surveys and aerial photographic equipment many changes and improvements have been made in the equipment and in the technique of using it. Aerial photographic operations have, been developed from the crude methods and apparatus of wartime to a science upon which exact engineer-ing calculations can be based. In the early days there was no airplane specially designed to meet aerial photographic requirements. One type of camera was used in all types of operations. Projects were made to conform to the products we could make and deliver. Obviously this entailed definite limitations. We now have airplanes designed specially for aerial photographic operations in accordance with the conditions encountered in actual service experience. We have cameras for every photographic purpose and our laboratory technique and equipment have been developed to the point where it is possible to make contour maps from vertical aerial photographs with contour intervals as close as five feet. Therefore, the selection of equipment now can be made in accordance with the time at our disposal, the justifiable cost, the scale desired, and the general requirements of the client. This does not mean, however, that arbitrary deliveries can be set for aerial photographic products. The factors in each project vary and each job must be considered in accordance with the factors involved. This accounts for the fact that products of aerial surveys may readily vary from $1.25 to $200 a square mile. Sherman M. Fairchild became interested in the design of a radically different aerial camera during the war. At its close he was about ready to demonstrate his design to the War Department. By 1920, he was able to bring out his first completed model. It had a number of radical features, one of which was the first dependable high-speed between-the-lens shutter, which makes for accuracy in aerial photographic work. Another feature was the use of metal throughout, eliminating the wooden parts that had been employed in wartime cameras. Another feature was the interchangeability of parts.

Jan 1, 1936

By John Birkinbine

Much has been contributed to the Transactions of the Institute concerning the construction and operation of American blast-furnares ; but the following compilation is offered as possibly furnishing additional information upon the general features, dimensions, locations, capacities, etc., of the blast-furnaces of the United States; while, incidentally, the ores upon which they rely are noted in a general way. The paper is presented chiefly as a compilation, and the figures given are selections from most reliable sources, or averages calculated from official statistics, placed for convenient reference, with a view of assisting those who consult the Transactions in determining the present relative merits and importance of various sections of the country. The scope of the paper has been restricted to as few topics as possible, and all the details of special plants, or notable outputs have been ignored. While every effort has been made to give correct figures and data, the changes which are constantly taking place in the iron-producing industry, will, undoubtedly, by the time the paper is in print, develop some errors. It is difficult to determine which of the blast-furnace plants of the country should or should not be considered as upon the active list. A number which have not been in operation for years are still reported as active, some of which will scarcely be put in blast again, and others are handicapped so that they can only operate in times of abnormal profits. It is therefore scarcely probable that there are over 600 blast-furnaces in the United States which can properly be considered as active; but so many considerations affect the various plants, that, it being impossible to determine the exact number, I have relied upon the annual reports presented to the American Iron and Steel Association. Concerning the number of plants which could be stricken from the list, the Secretary of this Association says: "In January last (1885) we enumerated 669 furnaces, which included many stacks which had not been in blast for a very long time, and others which could not be operated except during short periods of exceedingly high prices for pig iron. We have gone over this list very carefully and have eliminated 10 anthracite, 19 bituminous, vol. xiv.—36

Jan 1, 1886

By Tran K. Van, Francois E. Heuzé, Richard E. Goodman

Sound design of structures founded in or upon rock requires that the deformability of each rock member involved be characterized. This can be done by means of loading tests (plate bearing, flat jacks, borehole jacks, pressure chambers, etc.) or through convergence measurements (tunnel convergence, roof sag, etc.) in exploratory works. Analysis of data will be qualitative (degree of nonlinearity, creep behavior, scattering of results over a number of sites, etc.) and quantitative (modulus of elasticity or deformation). Some of these tests involve a very bulky apparatus and are expensive to perform. On the other hand, for the purpose of mapping and describing the various rock members which occur within a given site, many feet of diamond drill holes are frequently completed. Even with the optimum equipment and expert drillers, however, quantitative characterization of the rock units on the basis of tests on returned samples is apt to be misleading; the softer and weaker components of the rock tend to be lost and the fabric of the rock block- fracture system in situ is not sampled. Laboratory moduli of elasticity have proved to be consistently higher than in-situ values selected for engineering purposes. This led to the design of instruments which would operate in boreholes, combining the advantages of a reduced size and a deeper investigation, from the surface to several tens of feet. BOREHOLE DEFORMABILITY MEASURING INSTRUMENTS In the last 10 to 15 years, a number of testing devices have been con- structed which can be inserted into a borehole to apply a load and mea-

Jan 1, 1972

By J. Peperakis

Coal mine bumps are normally associated with pillar mining under moderate or deep cover. Severe bumps at Sunnyside, however, have not been confined to pillar lines. Many have occurred in virgin development and in localities a long way from active pillar workings. As early as 1918 bumps in virgin territory were attributed to the faulted structure in the Sunnyside area.' Sunnyside is an old property, mined for more than 60 years. Both man-made and natural conditions contribute greatly to bump occurrences, and loss of life and great destruction of workings have resulted from some unusual bumps in recent years. Before Kaiser Steel acquired the Sunnyside Mines in 1950, about 21 million tons of coal had been extracted. Large areas had been worked out and equally large areas first-mined. As demand for coking coal gradually diminished, extensive blocks were shut down, and during the low production period of the 1930's mining on a very limited scale was confined to a section of the property close to the coal tipple. Following purchase of the property Kaiser Steel developed the mines into a fully modernized operation. The worked out and first mined areas covered about four square miles extending five miles along the strike and up to one and a half miles down dip from the outcrop. The sections with favorable mining conditions and clean coal had been largely extracted under the selective mining system imposed by economic conditions and the lack of cleaning plant facilities. Large reserves remained on the fringes of the worked out sections and in areas under deep cover and difficult roof. There were also considerable reserves in first-mined areas. In recent years much of Sunnyside's daily output of 7000 to 8000 tons has been derived from the partially mined localities. Many bumps have occurred when pillars have been pulled within the first-mined areas and on the fringes. The bumps have been associated with retreating pillar lines backing up against old workings and pillar lines in old first-mined areas backing up against highly stressed oversized barrier pillars surrounded by smaller pillars. In some parts of the property the upper Sunnyside seam was extensively worked in the past, and sizable areas of old works overlie the present lower seam workings. Abutment pressures from barrier pillars and pillar remnants are transmitted to the lower seam, contributing to bumps and squeeze conditions. Cover: The terrain is exceedingly rough, and cover varies considerably over relatively short horizontal distances. For example, at No. 1 mine the 2000-ft cover line is ony 2700 ft from the coal outcrop, and at No. 2 mine the cover over the main hoisting slope increases from 1000 to 2000 ft in a horizontal span of 1200 ft. Cover over the present mining sections ranges from several hundred feet in the valleys to 2500 ft under the crest of the divides. A short distance ahead of Sunnyside's deepest development down dip the cover reaches 3000 ft or more.

Jan 1, 1959

By Julien F. Phillips, Donald E. Garrett

The production of soda ash from natural sources is one of the United States' oldest industries. The London Company, which financed the settlement of Jamestown, in the fall of 1608 exported in its first cargo from Virginia " . . . trials of pitch, tar, glass, frankincense, and soap-ashes."1 This last product, a crude mixture of sodium and potassium carbonates obtained by the burning of wood in iron pots, was the commercial soda ash of its day, used in the infant soap, glass, and bleaching industries. Besides having a good cash value, its production helped to clear the land, and it was a compact, easily shipped commodity. The extra high potassium content of these American "pot-ashes" gave them an added market as a fertilizer, a field that they dominated until the opening of the Strassfurt deposits in 1860. This form of natural soda ash disappeared forever from commercial importance with the introduction of the Le Blanc process (1791), and later the Solvay process for manufacturing soda ash. The Solvay process was rapidly accepted in the United States, and has accounted for most of the country's soda ash production since 1884. It was not until the western part of the country began to be developed that natural soda ash was again produced. A number of lakes, playas, and springs west of the Rocky Mountains were found to be rich in this mineral, and climatic conditions were ideal for its easy recovery by solar evaporation. The production of natural soda ash from these deposits has become a steadily growing industry in the United States. Production A summary of the production and value of natural sodium carbonates in the United States is presented in Table 1. Prior to 1927 the principal output came from several different companies at Owens Lake, California. Then production at Searles Lake, California, began to [ ] increase until it became the most important source. In 1948 the sale of crude trona from Green River, Wyoming, commenced and since that time production from these latter two areas has been about equal. Table 2 lists the four

Jan 1, 1960

Slovenliness is as reprehensible in words as in clothes. Much writing that we recognize as poor in style is merely sloppy. Just as some students postpone the necessary shave or forget to change their collars, so young engineers in writing drop their articles, definite and indefinite, or omit prepositions where they are required, possibly to compensate for those they use unnecessarily The work will begin [on] Saturday. Influenza seriously affected many mines [during] the last three months. Flotation in America [during] the last two years has made tremendous strides. Construction of the mill started [on] August 12, 1915, at which time 75% of the excavation was completed. The idea I wish to convey is [that] there are mineral deposits to which the present law applies badly. For this reason, if there was [for] no other, the ownership of the ore below and [of] the surface above should go together. When a unit of mapping is furnished, be the unit a claim or [a] group of claims, it is necessary . . . A fully stocked store was started in Park City and all employees [were] sold merchandise on a strictly cost basis. The word "merchandise" is left without government or agreement. 'I suggest: ". . . and merchandise was sold to all the employees on a strictly cash basis." The verb 'be' is serving concurrently both as a principal and as an auxiliary in the following: At first the work was interesting and [was] liked by most of the men. The sulphide ore was more complex or [was] milled at an increased cost. The failure to repeat the auxiliary verb in successive clauses is a common error, as in The filter is filled with liquid allowed to empty, and then ignited.

Jan 1, 1931

By Ben L. Seegmiller

Localized open pit slope failure was avoided as an apparent result of a practical rock mechanics program conducted at the Twin Buttes copper operation. The key to the program was the application of cable bolting, a technique that artificially supports open pit slopes using properly installed post-tensioned cables. As a result of the research and testing program, extensions of the cable bolting principal became significantly apparent. • The economics of artificial stabilization appear to be overwhelmingly favorable, and • Best practical applications are "final" pit slopes, slopes beneath permanent structures and potentially slope failing areas. Success of this research is manifested by the fact that similar stabilization systems are presently under consideration for Twin Buttes as well as other open pit operations.

Jan 12, 1974

By B. G. Langston, R. D. MacDonald, F. M. Stephens

WITH the development of uranium ores that contain substantial amounts of acid-consuming compounds, the alkaline leach has become an attractive method for extraction. Considerable work has been done on both atmospheric and pressure-leaching with aqueous solutions of sodium carbonate and sodium bicarbonate as the lixiviants.1,2,3 For the treatment of uranium-bearing limestones and other high-lime (CaO) ores, the sodium carbonate leach has proven attractive because it avoids the high reagent consumption incurred by the reaction of sulfuric acid with lime. In addition, the corrosion problems with sodium carbonate are negligible as compared with those encountered in the acid-leach system. The sodium carbonate leach, however, does not yield as high an extraction of the uranium as the acid leach and is not attractive for economic reasons when treating ores that are high in sulfates or sulfides.

Jan 9, 1957

By A. Raman, P. P. Singh

The constitution of the La-Rh system was studied by powder X-ray diffraction, metallopaphic, and differential thermal analysis techniques and an equilibrium diagram is presented. Eleven intermediate phases occur in the system and the crystal structural data for nine of them were determined. La3Rh crystallizes in an orthorhombic structure of undetermined type, whose unit cell is obtained by doubling the 'a; and 'c,,' edges of an FesC type unit cell. The other intermediate phases of the system are LarRh-3( undetermined structures also occur in the system. LaRh, undergoes a polymorphic phase transformation at 1240°C. LaRh3 and La2Rh7 also exhibit polymorphisnz. The phases Laah and LazRh7 melt congruently. The latter undergoes a eutectoid transformation into LaRh, and Rh at 1205°C. Laah3 is formed by a peritectoid reaction between Laah and La,Rh,,. The other Phases result from peritectic reactions between the liquid and the adjacent rhodium-rich phases. The intermediate Phases of the La-Rh system are compared with those of the La-Co and La-Ni systems. DURING the course of a detailed investigation to study the occurrence of CrB, FeB, A1B2, and related structures in the rare earth alloys it was found that much information is lacking for the rare earth noble metal systems. Although the structures of several rare earth alloys containing the noble metals at the AB and AB2 stoichiometries have been reported, the occurrence of related structures at other stoichiometries has not been studied. We have initiated a project to study the crystal structural features of selected rare earth-rhodium alloys and to map the equilibrium diagrams of representative systems with conventional methods. The results of our investigation in the La-Rh system are presented in this paper. Two phases were known in the La-Rh system. LaRh has the CrB-type structure.' LaRhz is a MgCu2-type Laves phase.z EXPERIMENTAL PROCEDURE Alloys weighing less than 1 g were prepared from commercially pure lanthanum (99.9 pct +), supplied by Lunex Company, Pleasant Valley, Iowa, and rhodium (99.92 pct +), supplied by Engelhardt Industries, Newark, N.J., in a conventional arc melting furnace under argon atmosphere. The buttons were turned upside down and remelted three times to insure homogeneity in the samples. Since negligible loss of material was encountered during melting, a chemical analysis of the alloy buttons was not undertaken. Powder specimens for X-ray diffraction studies in the as cast state were then prepared. The buttons were wrapped in thin molybdenum foils and homogenized by heating in vacuum at suitable high temperatures for more than 1 week. They were then broken into three or four pieces for annealing experiments. The pieces were wrapped in molybdenum foils and annealed at various temperatures in evacuated quartz capsules. The annealing was carried out for 2 hr at or above 1200°C, 1 day at temperatures close to llOO°C, 2 days at 1000°C, and for 1 week at temperatures below 1000°C. After annealing the alloy pieces were again broken and powder specimens for X-ray diffraction were prepared. The powders of the lanthanum rich alloys with more than 80 at. pct La were prepared by filing. The filings were sealed in molybdenum tubings and stress-relieved at 600°C in vacuum. It was not deemed necessary to stress-relieve the powders of the other alloys, since the alloys were very brittle and were ground easily. POWDER X-RAY DIFFRACTION X-ray diffraction photographs of powders (-325 mesh size) of the alloys in the as cast and annealed states were prepared in a Guinier-de Wolff focussing camera with copper K, X radiations. These patterns were studied to identify the stoichiometries and the crystal structures of the intermediate phases. The lattice parameters of the phases were calculated after minimizing the differences between the observed sin2 6 values, calculated from the diffraction angles 8, and the sin2 8 values, calculated using approximate lattice constants obtained from a few lines. These differences were minimized manually to less than 0.0005. The latLice constants are judged to be accurate to *0.005A for values less thp about 10A and to k0.01~ for values greater than 10A. The relative intensities of the lines were calculated using a computer program written by Jeitschko and Parthk.~ No attempt was made to refine the atomic positional parameters in the phases. METALLOGRAPHY The phase equilibria in the investigated alloys in the as cast and annealed states were also studied by metallographic examination. The polished specimen surfaces were etched with 10 pct picric acid in alcohol (alloys up to 25 pct Rh), concentrated picric acid (from 25 to 37.5 pct Rh), 2 pct nital (40 to 50 pct Rh), 10 pct nital (from 50 to 66.7 pct Rh) and with concentrated 48 pct HF for the other rhodium-rich alloys. Selected microstruture~ were then photographed using a Po-laroid Land camera. THERMAL ANALYSIS Differential thermal analysis of the alloys was carried out in DTA-668 Stone differential thermal ana-

Jan 1, 1970

By Charles C. Rodd

Prior to 1938, proration procedure in Kansas required the physical testing of wells in order to set up a basis for allocating production. Subsequently the use of liquid-level data and bottom-hole pressure data was authorized on certain types of wells as a basis for calculating well capacities, thereby permitting wells to be tested at low rates and with small volumes of production. This paper gives some attention to the equipment used for obtaining liquid-level data but in general it is devoted to the theoretical and physical factors involved in well testing by drawdown methods. These tests are divided into two classifications: (I) liquid-level data used directly to calculate capacities, and (2) liquid-level data and liquid-level measuring equipment used in connection with other data to determine bottom-hole pressure. Equations and calculations for both types are shown. Well capacities calculated from fill-up data have not been used generally but offer a simple means of testing some wells. Theoretical factors and calculations for such tests are shown. In the state of Kansas, proration laws required that the "ability of a well to produce" be given consideration in state allocation orders and for many years this was the only factor used in prorating the allowed oil. The "ability of a well to produce", was the quantity of oil that could be obtained from a well in a prescribed period, usually 24 hr. Early in the history of State-regulated proration, Kansas operators realized that, unless some restriction were placed upon equip- ment, the competition between producers to obtain large well "potentials" might result in a race to install the largest pumping equipment. Consequently, restrictions were placed upon the size of tubing and length of pump stroke that could be used in pumping wells during potential tests. Later, restrictions were placed also upon the size of tubing and chokes that could be used in flowing walls. Despite the restriction setup, better pumping equipment was designed and installed, pumps were improved, and various devices were invoked to obtain high rates of production for short periods of time. By 1937 pumping cycles of forty to forty-five 54-in. strokes per minute were not uncommon, and numerous wells had produced at the rate of 3500 bbl. per day for short periods. Such production was far beyond any rate that could be long sustained. Equipment necessary to take "potentials" was several times larger than that needed for normal producing purposes, and repairs and replacements required by the high pumping speeds were excessive. Also, many operators suspected that the high rates of production main tained during '"potential" tests were conducivc to early water encroachment. By 1938 large-scale physical testing of wells in Kansas ended, the use of the bottom-hole pressure gauge had become common, engineers and operators were becoming familiar with the term ''productivity index," and bottom-hole pressure was being used as a factor in allocation in many areas. There were many drawbacks, however, to large-scale use of

Jan 1, 1943

By Charles C. Rodd

Prior to 1938, proration procedure in Kansas required the physical testing of wells in order to set up a basis for allocating production. Subsequently the use of liquid-level data and bottom-hole pressure data was authorized on certain types of wells as a basis for calculating well capacities, thereby permitting wells to be tested at low rates and with small volumes of production. This paper gives some attention to the equipment used for obtaining liquid-level data but in general it is devoted to the theoretical and physical factors involved in well testing by drawdown methods. These tests are divided into two classifications: (I) liquid-level data used directly to calculate capacities, and (2) liquid-level data and liquid-level measuring equipment used in connection with other data to determine bottom-hole pressure. Equations and calculations for both types are shown. Well capacities calculated from fill-up data have not been used generally but offer a simple means of testing some wells. Theoretical factors and calculations for such tests are shown. In the state of Kansas, proration laws required that the "ability of a well to produce" be given consideration in state allocation orders and for many years this was the only factor used in prorating the allowed oil. The "ability of a well to produce", was the quantity of oil that could be obtained from a well in a prescribed period, usually 24 hr. Early in the history of State-regulated proration, Kansas operators realized that, unless some restriction were placed upon equip- ment, the competition between producers to obtain large well "potentials" might result in a race to install the largest pumping equipment. Consequently, restrictions were placed upon the size of tubing and length of pump stroke that could be used in pumping wells during potential tests. Later, restrictions were placed also upon the size of tubing and chokes that could be used in flowing walls. Despite the restriction setup, better pumping equipment was designed and installed, pumps were improved, and various devices were invoked to obtain high rates of production for short periods of time. By 1937 pumping cycles of forty to forty-five 54-in. strokes per minute were not uncommon, and numerous wells had produced at the rate of 3500 bbl. per day for short periods. Such production was far beyond any rate that could be long sustained. Equipment necessary to take "potentials" was several times larger than that needed for normal producing purposes, and repairs and replacements required by the high pumping speeds were excessive. Also, many operators suspected that the high rates of production main tained during '"potential" tests were conducivc to early water encroachment. By 1938 large-scale physical testing of wells in Kansas ended, the use of the bottom-hole pressure gauge had become common, engineers and operators were becoming familiar with the term ''productivity index," and bottom-hole pressure was being used as a factor in allocation in many areas. There were many drawbacks, however, to large-scale use of

Jan 1, 1943

By C. P. Parsons

During the past year considerable interest has been shown in cementing operations for shutting off bottom water, whipstocking, etc. A number of plug-back methods have been used, with various adaptations for special conditions, but those described in this paper are representative of the methods now in use. Conditioning the Well Various preliminary operations for improving the results from plug-back operations have been evolved. In one method, a nitroglycerin shot is discharged at the upper portion of the formation to be plugged off, the purpose being to make a wide place in the hole in order to give the cement a more secure anchor against thrust pressure of the water against the bottom of the cement plug after the well is again put on production. Another is intended to attain a similar result by under-reaming a wide place in the hole by means of a rotary wall scraper. In one well in which this device was used there was a water sand at the bottom of the well immediately below the cap rock above which the oil sand occurred. Before the plugging back operation, the water sand was underreamed in an attempt to get a square shoulder on the underside of the cap rock, in order to prevent the water from breaking in over the top of the cement plug after the well should be put on production, and also to get a more secure anchor for the cement plug against the thrust pressure of the water against it. As an aid in calculating the amount of cement required to fill a given amount of hole to be plugged back, a device has been developed for measuring and recording the irregularities and cavities in open holes, called an "open-hole recording caliper." If consists of a steel shell, 5 in. in diameter, which encloses a recording mechanism that receives impressions from four movable arms that make sliding contact with the wall of the hole. The arms operate a ratchet, which raises and lowers a recording stylus against a chart. Each arm registers its own radius. The device is run into a well on a steel measuring line. While the device is being lowered, the arms are folded inside the shell; they are

Jan 1, 1936

By C. P. Parsons

During the past year considerable interest has been shown in cementing operations for shutting off bottom water, whipstocking, etc. A number of plug-back methods have been used, with various adaptations for special conditions, but those described in this paper are representative of the methods now in use. Conditioning the Well Various preliminary operations for improving the results from plug-back operations have been evolved. In one method, a nitroglycerin shot is discharged at the upper portion of the formation to be plugged off, the purpose being to make a wide place in the hole in order to give the cement a more secure anchor against thrust pressure of the water against the bottom of the cement plug after the well is again put on production. Another is intended to attain a similar result by under-reaming a wide place in the hole by means of a rotary wall scraper. In one well in which this device was used there was a water sand at the bottom of the well immediately below the cap rock above which the oil sand occurred. Before the plugging back operation, the water sand was underreamed in an attempt to get a square shoulder on the underside of the cap rock, in order to prevent the water from breaking in over the top of the cement plug after the well should be put on production, and also to get a more secure anchor for the cement plug against the thrust pressure of the water against it. As an aid in calculating the amount of cement required to fill a given amount of hole to be plugged back, a device has been developed for measuring and recording the irregularities and cavities in open holes, called an "open-hole recording caliper." If consists of a steel shell, 5 in. in diameter, which encloses a recording mechanism that receives impressions from four movable arms that make sliding contact with the wall of the hole. The arms operate a ratchet, which raises and lowers a recording stylus against a chart. Each arm registers its own radius. The device is run into a well on a steel measuring line. While the device is being lowered, the arms are folded inside the shell; they are

Jan 1, 1936

By W. Klement

By quenching liquid alloys, single-phase solid solutions are obtained in the ranges 0 to 42.0 at. pct Co-Au and 0 to 15 and 75 to about 100 at. pet Co-Cu. Metastable solid solutions are also found in multiphase 42.0 to 49.0 and 69. 0 to about 100 at. pet Co-Au alloys. fie inability to achieve complete solid solubiliiies in Au-co and cu-co alloys is rationalized by a conszderation of the rate processes during cooling and solidification. Trends in lattice distortion and shifts in the compositions of the melting-point minima and critical points are discussed for the binary alloys of copper, silver, and gold with some of the transition metals of the first long period. By rapidly cooling alloys from the melt, a continuous series of metastable solid solutions can often be obtained for components of similar crystal structure which normally form eutectic systems.' The eutectic system Au-Co, Fig. 1, and the peritectic system Cu-Co, Fig. 2, were investigated in order to determine the extent of the metastable solid solutions attainable with the present technique.* EXPERIMENTAL PROCEDURES Most of the alloys were prepared by melting weighed quantities of the elements (purity greater than 99.9 pct) under hydrogen in alumina crucibles by means of induction heating. After reweighing, the alloys were cast under argon into 1 mm diam wires. However, it was not possible to prepare some of the Cu-Co alloys with the requisite homogeneity (over about 1 mm3) in this way. For these alloys, reduced powders (purity greater than 99.9 pct) were mixed for 12 to 48 hr, pressed into compacts that were sintered at 1000º to 1050°C for 6 to 48 hr under hydrogen, and then furnace-cooled. Alloy charges of a few mm3, cut from the cast wires or chipped from the sintered compacts, were heated to 1550º to 1600°C in 30 sec in an alumina insert held within a graphite support and then ejected by a pulse of helium onto a lightly polished copper strip on the inner periphery of a rotating wheel. The

Jan 1, 1963

By Franz R. Dykstra, R. F. Tatnall

A ferroalloy is defined as: "An alloy of iron with some element other than carbon used as a vehicle for introducing such an element into the manufacture of steel. The element may alloy with the steel by solution or, as the carbide, -neutralize the harmful impurities, by combining with them and separating from the steel as flux or slag before solidification."a The most commonly used ferroalloys are: ferromanganese, ferrochrome, ferrosilicon, ferrovanadium, ferromolybdenum, ferronickel, ferrotungsten, ferrocolumbium, and ferrophosphorus. Concern here is with the sources and markets of the major metallic alloying elements. The discussion is further restricted to those - ferroalloy ores, the principal use of which is in the production of steel. Phosphorus, silicon, and tungsten, for example, are ferroalloys of some economic significance, but other uses dwarf their alloying applications. Thus, this discussion will deal with the ores of managanese, chromium, nickel, molybdenum, vanadium, and columbium. As shown in Table 14.1B.1 ferroalloys serve to- facilitate processing and impart to the finished steel such characteristics as tensile strength, ductility, low-temperature impact, hardenability, high-temperature strength, corrosion resistance, toughness, and abrasion resistance. In the steel-making process, ferroalloys may be added in the charge, in the molten bath near the end of the finishing period, in the ladle, or in the molds. Timing of the addition depends on the effect of the addition on the temperature of the molten metal, the formation and elimination of reaction products, and the protection of subsequent additions from oxidation. MANGANESE General Approximately 95% of the manganese ore sold is consumed by the steel industry, either as ferromanganese or as manganese metal. Manganese is the universal alloy, without which good steel cannot be made. It serves as a scavenger, removing phosphorus, sulfur and, to a degree, oxygen from the melt. As an alloying material it makes steel hard, tough, and resistant to wear. Approximately 6 kg of manganese is required for every ton of common steel produced by United States steelmaking practice. The remaining 5 % of the manganese ore consumed consists of special or so-called "chemical" ores, including high-grade pyrolusite ores, electrochemically reactive "battery ores," and a number of special varieties, as well as those otherwise regarded as "metallurgical ores."

Jan 1, 1976

By A. E. Lehman

A RECENT demand for some form of panoramic display of an important railway line, showing its branches, connections, and terri tory controlled by it, revealed to the writer the advantages of' a topographical model or relief map fix this purpose. Hitherto, maps of this nature have been used chiefly for scientific and geographical purposes, and confined to a comparatively narrow field of service. They deserve to become more popular and to have their advantages better understood. Much has been written and accomplished in this direction by Prof. Lesley, Messrs. Harden, Moulten, de Mendonca Cortez, and others; but I believe their pub lished descriptions of the methods employed in the construction of these models are confined to those used by themselves. It is the writer's aim to present in condensed form these various methods, and some suggestions of practical value as to the most economical course of procedure, as well as to mention some of the uses that may be made of the results obtained Methods of Construction.—Many different materials have been prepared and used in the preparation of relief maps, such as metal, clay, plaster, gypsum, wax, putty, Card-board, papier-mache, wood, and compositions of varions kinds, with results more or less success ful : wood, however, in the writer's experience, has been found to be by far the most satisfactory, combining the advantages of stability, accuracy and ease of handling. The following is a brief description of several of the methods used in constructing topographical models : When clay, wax, putty, compositions or materials of a plastic nature are used, the operator carries his work up from its base by means of measurements or by the eye, manipulating and shaping the material as best he can, ac cording to such features of his subject as he wishes to delineate. This process requires remarkable skill, and given this, will probably fall short even then of an approximation to accuracy; lacking essential elements of detail nil over the work and exactness, particularly in position and elevation of the most important points in the territory mapped. When either of the above mentioned materials or compositions are used, metal or wooden pins are sometimes driven into the base or level datum plane of wood, the top of these pins giving the eleva-

Jan 1, 1886