Search Documents

By E. S. Machlin

The alternate processes by which solute atoms can limit the migration of grain boundaries have been considered. At the lowest solute concentrations the controlling process is "mechanical breakaway" in which the solute atoms affect the driving force and not the mobility. In the next higher range of solute concentration, solute atoms are bound to the boundary and diffuse by boundary diffusion along cusps in the boundary developed at the solute atoms. In this region the boundary velocity is controlled by the component in the direction of boundary migration of the rate at which the bound solute atoms can diffuse along the boundary. At still higher concentrations, it is predicted that boundaries break away from the binding solute atoms by thermal activation. The specific behavior Predicted is consistent with the observations of Aust and Rutter. The most striking agreement between prediction and experiment is that obtained for a range of solute concentration in which the boundary velocity is inversely proportional to the cube power of the solute concentration. MaNY models have been devised for the atomic steps in the motion of a grain boundary. McLean1 has listed some of these models and Aust and utter' have evaluated these and other models. If there are

Jan 1, 1962

By W. A. Schaeffer, M. Albertson

The Yates field is situated in northeastern Pecos County, Texas. Its productive area is about 15,000 acres. Production is chiefly from limestone of Permian age. Depths of wells vary from 1100 to 1800 ft. Initial productions range from a few barrels to 8000 bbl. per hour. The field outlet has always been prorated. Gas-oil ratios originally varied from less than 100 cu. ft. up to 8000 cu. ft. per barrel at allowable production rates. The average ratio was about 500 cu. ft. Fig. 1 shows the structure of the field and the location of the Tippett lease, on which the original experimental tubing work was done. Before the latter part of the year 1929, little actual effort in practice had been given to determination of the conditions under which the highest efficiencies may be realized in naturally flowing wells. For the preceding few years attention had been given to gas-oil ratios and their possible reduction by maintenance of back-pressure by choking at the well head. Some attempts had been made toward reduction of ratio by bottom-hole choking. In late 1929, the Shell Petroleum Corp. started the experimental installation of specially designed flow columns adapted to high-pressure flowing conditions in the Yates field. The objectives in view were the attainment of low gas-oil ratios at low rates of flow and the maintenance of high bottom-hole pressures. All naturally flowing wells should be provided with a suitable eductor string immediately upon completion of the well, so that the benefits of efficient flow will be derived from the beginning. This paper presents a method of tubing for efficient flow and a discussion of some complex factors which influence well behavior. Factors Influencing Gas-oil Ratios Many factors influence the production of gas from naturally flowing wells. The writers believe that in some instances gas control is effected mainly in the reservoir itself, in others in the well bore, and in still others both sets of factors may be significant. Some wells apparently have penetrated productive zones in which practically all of the gas is closely associated with, and mostly dissolved

Jan 1, 1932

By G. M. Ritcey, M. J. Slater, B. H. Lucas

The recovery of uranium from acid leach slurries by continuous ion exchange, or solvent extraction using sieve-plate pulse columns, is compared. Differences in processing costs are of prime concern and can be related to differences in the unit operations of the two methods, as well as the chemical and physical properties of the slurry. Parameters are defined for the operation of the solvent-in-pulp process and the design of the continuous ion exchange column. Pilot plant operating experience with both recovery systems is described, and an overall assessment of the relative costs is presented.

Jan 1, 1973

By Jesse O. Betterton

IN the last analysis, two basic factors influence the use of metals and alloys; namely, cost and adaptability to the use under consideration. These are so interrelated that to study the properties of metals or alloys without considering the prices and price trends is quite illogical. Lead has been a cheap metal, selling in 1932 for the extremely low price of 2.56 cents per pound. The cheapness of lead in the past was not due to a particularly abundant supply of the element in the earth's crust but rather to the ease with which it was won from its ores and to the chemical stability of the metal, preventing its dissipation. Today, however, our modern economy has caught up with the distribution of lead in the earth's crust and the price is largely dictated by the supply of concentrates readily available for smelting, and which can be placed quickly upon the market. The demand for lead, particularly in times of stress, has brought the price up to the level of 19 cents in the United States, where the price is controlled by Government decree, and the price has been even higher in the world markets. The higher price for lead has changed the uses for this metal to a marked degree, driving it out of the fields where it is not essential. Lead articles of great antiquity have been found in Egyptian ruins, proving the stability of the element and indicating the basic simplicity of its metallurgy. It is probable that lead was the first

Jan 1, 1953

By Henry Howland

INTRODUCTION DURING the last decade no topic has created more interest or received more thought among blast-furnace men than colic. One reason for this is, undoubtedly, the remarkable increase in the use of byproduct coke. Formerly our coke was made at a distance from the furnaces and by a distinct organization. There was little cooperation or development possible under these conditions. Today the situation is greatly changed. Much of our coke is made by the organization operating the furnaces and the coke oven is operated with the primary object of obtaining the best results in the blast furnace. The effect of changing the method of coke manufacture, even in some minor detail, is often felt almost immediately at the blast furnace. There naturally results one of the most valuable assets of the byproduct coke oven, -i.e., the possibility of increased blast-furnace efficiency clue to close observance and correct operation of the ovens. The results are evident, but it often is difficult correctly to account for them. In attacking the solution of a problem of as much importance as why one coke is better than another, there are facts which should be kept clearly in mind The author hopes, in this paper, to bring out some points relative to the use of carbon in the blast furnace which will be of value in solving this question.

Jan 3, 1916

FRIENDS of the late Charles F. Rand presented in 1930 a sum of money from which the income is available to support various phases of the work of the Institute in which Mr. Rand was so deeply interested. At present the fund amounts to $10,900. The specific terms of the deed of gift are as follows: "The fund collected to establish a memorial to the late Charles F. Rand shall be placed in the custody of the Board of Directors of the American Institute of Mining and Metallurgical Engineers, to be set up as a trust to be known as the `Charles F. Rand Foundation,' the income of which shall each year be applied to a distinct purpose to be decided upon in that year by vote of the Board of Directors. This purpose shall be such as to promote the general welfare of the Institute and to constitute a permanent memorial of the usefulness of Mr. Rand, who for many years gave unstintingly of his time and talents in its service. "It shall be within the discretion of the Board of Directors to establish a medal to be known as the Charles F. Rand Memorial Medal to be awarded at such a time and under such rules as may be determined by the Board of Directors, for Distinguished Achievement in Mining Administration." The establishment of this medal was announced at the annual meeting in February, 1932, the term "mining" being defined in its broad sense to include metallurgy and petroleum. Robert Linton is chairman of the Charles F. Rand Foundation Award Committee.

Jan 1, 1942

By Robert Gilman Brown

The original power-plant of the Standard Company has been described* by Mr. T. H. Leggett, late president and manager of the company; but since the presentation of his paper considerable additions have been made, which will be found interesting because of the engineering features involved and of the attainment of a high degree of flexibility with the inflexible, two-wire, alternating system of electrical transmission. Although these additions have been completed during the last year, they constitute, to a large extent, only the carrying out of plans that belonged to the original conception of the installation. The regular operation of the water-power through the winter proved very difficult; there was a considerable length of ditch to be kept open, and, as the stream is small and any freezing night may stop the whole flow of water, there was the .additional trouble of having no reserve to draw upon. The rule for the winter is, that after a night of hard frost water begins to move in the canon before noon on all but the coldest days. To obviate the nuisance of the anchor-ice, and to make available all of the water, a dam of sufficient height to impound several days' run of water has been built across the canon, 3875 feet above the power-house, and provided with pressurepipe well below the surface. In place of the 1571 feet of pipeline from penstock to power-house, there has been substituted a line 3875 feet long to bring water direct from the dam. The dam is of logs, cribbed up in squares of about 12 feet, ballasted with earth and rock and sheathed on the water-face with 3-inch plank.

Jan 1, 1897

By Ralph E. Grim

THE technology of clay minerals is defined, for the purpose of this review, as- the application of fundamental data regarding clay minerals, and techniques of handling them, to the various industries, arts, and professions concerned with clay materials. The aim of the paper is to narrate recent developments in clay mineral technology. This review does not claim to be complete, and perhaps gives undue emphasis to matters that have been worked on in the author's laboratory or with which he has some other connection. In the United States in recent years, particularly since the end of World War 11, interest in clay mineralogy has increased greatly. Many laboratories in many different fields have embarked on studies of clay minerals but unfortunately much of this work has not been published. CERAMICS In the field of ceramics, in recent years, a great deal of interest has developed in clay mineralogy. Papers too numerous to be reviewed here have been published portraying the clay mineral composition of substantially all the important types of ceramic clays in all countries. There has been a growing tendency to attempt to solve processing problems on the basis of clay mineral data rather than chemical analytical data. Likewise, there is an in- creasing tendency to control the characteristics of raw materials on the basis of clay mineral composition rather than chemical composition. In the United States in the last few years something like 50 differential thermal analyzers have been set up, and many are for the sole purpose of controlling raw material and processing. The ceramic industry is currently increasing its attention to the influence of exchangeable ions and soluble salts on physical properties. Ion concentration in clay suspensions has long been a matter of interest, but now it is also of interest in clays in the plastic state because of its recognized importance in the plastic, shrinkage, and bonding properties of clays. Students of clay have long recognized that an understanding of the plastic properties of clays is based on an understanding of the character of the water in clay-water systems, the nature of the binding force between individual clay mineral particles, and the factors that control the character of the water and the nature of the bonding force. In the last few years, some extremely important contributions have greatly increased the understanding of the nature of water adsorbed on the clay mineral surfaces. In this connection the work

Jan 1, 1952

By Thomas Egleston

The process of lixiviating silver ores, which do or do not contain gold, by means of hyposnlphite of soda is likely to assume a very great importance in the West, the conditions being such that while it is applicable to very rich ores which do not contain lead enough to smelt, it is also equally applicable to many ores that are either too poor or too impure to be treated by any other process. Western ores are generally divided into four classes: those which contain copper enough to be smelted for copper, from which the gold and silver is extracted in the wet way, as is the practice of the Boston and Colorado works; those in which there is a large quantity of lead, which can be smelted for lead, and the gold and silver extracted from it; ores in which there is neither copper nor lead enough to allow of a process of smelting, but which can be treated in pans, these ores being " free milling " if they require no metallurgical treatment, or '(rebellious" if they have to be roasted with or without the addition of salt; and ores which do not contain enough either of lead or copper for smelting, which are poor both in silver and gold, contain large amounts of sulphur, arsenic, and antimony, and cannot be treated in many places in the West by any of these processes. Roasting with salt would convert the base metals as well as the silver into chlorides, and would give in the amalgamation a very base bullion, and the expense of the process would be SO great that the margin of profit would be very small, the reason being that for the ordinary process of pan-amalgamation, which is the only one suitable for ores containing small amounts of the base metals, and poor in silver and gold, the cost of a plant for milling is so large as not to justify the expense of treating such ores. The electrolytic processes which have been partially successful in Europe have not been tried 'here. While in the near future they will undoubtedly be used, it is hardly possible to consider them now.

Jan 1, 1884

By L. W. Davies

A problem often encountered is the provision of materials which have impurity contents below a certain specified level. This problem is in some cases solved by making use of the segregation of the impurity with respect to the liquid and solid states of the material: an ingot of the material is subjected to directional solidification and the ends of the ingot. which are richer in solutes which respectively raise and lower the melting point of the solvent, are removed. An important extension of this process is the zone-refining process invented by pfann,' in which molten zones are passed successively along the length of an ingot and displace solutes towards the ends. Pfann's process is particularly appropriate in cases for which the segregation coefficient k does not differ greatly from unity, or when the impurity content must be kept extremely low (-=,6 atom fraction); it is widely used, particularly in the purification of materials for use in semiconductor electronic devices. It is the purpose of this paper to investigate theoretically the efficiency of the above refining processes; that is! we determine the most economic method of attaining a given yield of solvent of specified purity, taking into account the variables of the process. One variable of interest is the effective value of the segregation coefficient. which depends on the rate of movement of the liquid-solid interface and on the degree of stirring in the liquid; in addition to this, in the zone-refining process we are also interested in the choice of zone length for most efficient operation. A mathematical determination is made here of the lengths of successive molten zones which give, for an initially uniform distribution, the most efficient removal of a solute of arbitrary distribution coefficient. In order to be able to give a quantitative treatment of efficiency, we first define figures of merit applicable to a given distribution of solute. FIGURE OF MERIT Let an ingot of length L contain a distribution y(x) of solute: we confine our discussion to mono-tonic distributions, in order to avoid inconsistencies in the subsequent analysis. The first moments of the distribution about the origin and x = L are respectively L F = hy{x)dx [I] G = f(L -x)y(x)dx = YoL2-F, [21 where yoL is the total amount of solute present. We shall see that the quantities F and G are useful figures of merit for a discussion of the efficiency of zone-refining processes. In the first place, it is

Jan 1, 1960

By D. B. Dowling

The interest which has been aroused in prospecting for oil in the foothills of southern Alberta, and in the oil possibilities of the known gas fields situated in the less-disturbed areas, called for a much closer examination of the structure, thickness, and composition of the underlying rocks of the region than had hitherto been made. The areal geology of the larger part of the great plains was outlined by Dawson, McConnell, and Tyrrell, between 1881 and 1885. The foothill area was not critically examined at that time, owing to the time which would have been required for its proper study and the difficulty that was found in recognizing in the foothills the divisions which had been adopted in the mapping of the formations of the plains. This was due in great measure to the paucity of exposures in continuous sections of the lower divisions of the Upper Cretaceous. Since the pioneer work on the plains was published, the beds which form continuations south into Montana have been critically examined, The Canadian beds arch over the end of a flat anticline which rises to the south; and two sections in Montana, one on each side of the anticline, help to explain some of the difficulties previously encountered in the mapping of the measures found in the foothills. The index map, Fig. 1, shows the area studied, and its relation to southeastern Alberta, and to Montana. Problems of Correlation The principal difficulty experienced in correlation was in connection with the measures known as the Montana group. The beds of this group did not seem to agree in the two Montana sections. They showed the same differences to some extent as are encountered in comparing the foothill measures with those of the plains. The Montana group in Dakota and Manitoba consists of a series of shales of marine origin. In the eastern Montana section two sandstone members appear, leaving a shale member at the top and another

Jan 1, 1916

By William P. Blake

The occurrence and distribution of phosphorus is one of the most important questions with which the steel-maker has to do. Large sums are invested in processes for the removal of this element from ores before they come to the blast-furnace, and much greater sums in freeing the pig-iron from it. Mechanical engineers are becoming more and more critical of the amount of total phosphorus left in structural steel, the tendency being to require that it be reduced to the lowest possible figure. The old maximum of 0.1 per cent. is now considered much too high for first-class structural steel, and demands for 0.03 to 0.01 per cent. are by no means unheard of. The first to speak, in a scientific way, of the harmful effect of phosphorus on iron and steel appears to have been Meyer, who, in 1781, made mention of what we now term "cold-shortness," ascribing it to the presence of this metalloid, but not suggesting any remedy. It is, however, doubtful if a clear idea of this subject was possessed by the scientific world until after the invention of the pneumatic or Bessemer process, in 1855-56. One of the chief obstacles in the way of this renowned metallurgist,—one, indeed, the removal of which was the sine qua non of success,—was the phosphorus in the iron blown. The effect of the phosphorus does not seem to have been apprehended until many and costly experiments had been made, and then the required minimum percentage of it in the iron was secured only by the use of low-phosphorus ores. It was not until '1879-80 that practical success was reached, by the Thomas process, in the actual removal of the phosphorus from the iron. We now know something of the effect of the total amount of phosphorus on iron and steel, but very little as to the effect of the condition of the phosphorus. The state of combination in which

Jan 1, 1893

By J. N. Breston, R. V. Hughes

Conclusions drawn by previous research workers with reSPect to the relation between Pressure gradients and/or velocity and oil recovery obtained by laboratory water flood tests have been in disagreement probably due to variable procedures and unnatural conditions and materials. The Bradford Laboratory of the Pennsylvania Grade Crude Oil Association as part of its secondary recovery research program has conducted nineteen water floods on two long cores of widely differing characteristics in an attempt to clarify this relationship and make it an aid in predicting flooding pressures in the field. Unlike previous research procedures the present experiments were conducted with the aim of duplicating field conditions as closely as possible by using long unextracted consolidated cores, a live crude, and natural brines for both flooding and, connate water content. Also, the pressure gradients and flooding velocities were representative of field conditions where similar sands were being flooded. Eleven floods on one core and eight floods on the other core showed increased recoveries and lower residual oil saturation with increased flood pressure gradients and flood velocities. A marked decrease in recovery was obtained from both cores at very low flood velocities. This pressure versus recovery relationship is shown to hold up to the point of water breakthrough and also up to the 100 and 1 produced water to oil ratio point. INTRODUCTION The possibility of water flooding oil sands was suggested by Carl1 of the Pennsylvania Geological Survey in 1880. It is not known when the practice was tried intentionally for the first time, but its beneficial effects were noted in the annual production rate of the Bradford field as early as 1907. The practice was illegal in Pennsylvania until 1921. Early water floods in the Bradford field usually consisted of shooting or splitting the casing secretly to permit subsurface waters to enter the producing sands under hydrostatic head. As it was noted that the benefits of water flooding seemed to be proportional to the quantity of water dumped into the well many also began to utilize surface sources after the practice became legal. It was probably during the middle 20's before many producers realized that the pressurehead of the water upon the producing sand determined the rate and quantity of water that would enter the sand. Hence, rate and quantity of production appeared to be a direct function of input pressures. By 1927 a few producers had ventured the installation of pressure pumps in order to increase water-input rates and production through the combination of hydrostatic and hydraulic pressures. The adoption of pressure flooding and the "five-spot" drilling pattern in the Bradford field were essentially simultaneous. Water-input pressures in 1930 seldom exceeded 300 p.s.i. at the well head or 1100 p.s.i. at the sand face. Since that time, water-flood producers in the Bradford-Allegany fields have gone to higher and higher pressure until today 600 p.s.i. at the well heads is called a low pressure flood. Many high pressure floods now operate at 1300-1400 p.s.i. at the well head. The limiting and advisable pressure at the sand face has been pronounced as that pressure just under what is required to lift the overburden or to cause formation parting: According to this rule any water flood operation utilizing well-head pressures nearly equal in pounds per sq. in. to 1.1 times the average depth in feet to the top of the producing sand would be considered as a high-pressure flood. Despite the higher pressure trends in the Bradford-Allegany field operations and the results of early laboratory water flooding research, the desirability and benefits of high input pressures are still questioned by many operators, particularly in midwestern water flood operations. The present paper recounts a series of 19 laboratory water floods using two long, consolidated cores of widely differing characteristics saturated with live crude and flooded with oil field brines in an effort to simulate field conditions under • various pressure gradients and flooding velocities. For both cores, higher recoveries and lower residual oil saturations were obtained at higher pressure gradients and flood velocities. This relationship is shown to hold up to the water breakthrough point and also up to the 100 to 1 produced water to oil ratio point.

Jan 1, 1949

By R. V. Hughes, J. N. Breston

Conclusions drawn by previous research workers with reSPect to the relation between Pressure gradients and/or velocity and oil recovery obtained by laboratory water flood tests have been in disagreement probably due to variable procedures and unnatural conditions and materials. The Bradford Laboratory of the Pennsylvania Grade Crude Oil Association as part of its secondary recovery research program has conducted nineteen water floods on two long cores of widely differing characteristics in an attempt to clarify this relationship and make it an aid in predicting flooding pressures in the field. Unlike previous research procedures the present experiments were conducted with the aim of duplicating field conditions as closely as possible by using long unextracted consolidated cores, a live crude, and natural brines for both flooding and, connate water content. Also, the pressure gradients and flooding velocities were representative of field conditions where similar sands were being flooded. Eleven floods on one core and eight floods on the other core showed increased recoveries and lower residual oil saturation with increased flood pressure gradients and flood velocities. A marked decrease in recovery was obtained from both cores at very low flood velocities. This pressure versus recovery relationship is shown to hold up to the point of water breakthrough and also up to the 100 and 1 produced water to oil ratio point. INTRODUCTION The possibility of water flooding oil sands was suggested by Carl1 of the Pennsylvania Geological Survey in 1880. It is not known when the practice was tried intentionally for the first time, but its beneficial effects were noted in the annual production rate of the Bradford field as early as 1907. The practice was illegal in Pennsylvania until 1921. Early water floods in the Bradford field usually consisted of shooting or splitting the casing secretly to permit subsurface waters to enter the producing sands under hydrostatic head. As it was noted that the benefits of water flooding seemed to be proportional to the quantity of water dumped into the well many also began to utilize surface sources after the practice became legal. It was probably during the middle 20's before many producers realized that the pressurehead of the water upon the producing sand determined the rate and quantity of water that would enter the sand. Hence, rate and quantity of production appeared to be a direct function of input pressures. By 1927 a few producers had ventured the installation of pressure pumps in order to increase water-input rates and production through the combination of hydrostatic and hydraulic pressures. The adoption of pressure flooding and the "five-spot" drilling pattern in the Bradford field were essentially simultaneous. Water-input pressures in 1930 seldom exceeded 300 p.s.i. at the well head or 1100 p.s.i. at the sand face. Since that time, water-flood producers in the Bradford-Allegany fields have gone to higher and higher pressure until today 600 p.s.i. at the well heads is called a low pressure flood. Many high pressure floods now operate at 1300-1400 p.s.i. at the well head. The limiting and advisable pressure at the sand face has been pronounced as that pressure just under what is required to lift the overburden or to cause formation parting: According to this rule any water flood operation utilizing well-head pressures nearly equal in pounds per sq. in. to 1.1 times the average depth in feet to the top of the producing sand would be considered as a high-pressure flood. Despite the higher pressure trends in the Bradford-Allegany field operations and the results of early laboratory water flooding research, the desirability and benefits of high input pressures are still questioned by many operators, particularly in midwestern water flood operations. The present paper recounts a series of 19 laboratory water floods using two long, consolidated cores of widely differing characteristics saturated with live crude and flooded with oil field brines in an effort to simulate field conditions under • various pressure gradients and flooding velocities. For both cores, higher recoveries and lower residual oil saturations were obtained at higher pressure gradients and flood velocities. This relationship is shown to hold up to the water breakthrough point and also up to the 100 to 1 produced water to oil ratio point.

Jan 1, 1949

By Frederick G. Tickell

Petroleum engineers are displaying considerable interest in those fundamental properties of matter and energy that control the phenomena of oil and gas production. The subject is a difficult one to investigate by laboratory experiments for two reasons: (1) it is impossible to reproduce in the laboratory the scale of forces and dimensions that exist in the underground reservoir; (2) if we attempt to scale down the dimensions we are unable to reduce all proportionally. It is as if we tried to construct a model blast furnace for the reduction of iron ore, and reduced all lineal dimensions. We should find that the interstices between the miniature chunks of ore would not permit rapid transfer of gases, that combustion and heat transfer would not take place as in the full size furnace and that, in short, the contraption would not work. Just so, when we attempt to make a reduced scale oil field we find we must have, not only miniature reservoir and miniature wells, but "miniature" sand, 011, gas, etc. Much valuable work, however, has been done along these experimental lines and more will no doubt follow, but investigators should bear this point in mind and strive to attain dimensional homogeneity and dynamical similarity in order that their conclusions may be translated into terms applying to the oil reservoir. As Gibson says,' "These conditions are attained when all terms of the physical equation have the same dimensions, . . . when all corresponding particles of the two systems trace out similar paths and when the velocities are such as to make all corresponding forces acting on two such particles in the same ratio." It is the purpose of this paper to discuss the mechanics of fluid movement as it pertains to the oil pool and to point out the complexity of the laws of fluid delivery under the conditions often found. We have to do, fundamentally, with confined fluids, possessing potential energy whose expenditure is restricted by certain properties of the confining media and of the fluids themselves. The equation of motion and time is completely stated when we can assign values to the propulsive

Jan 1, 1929

By W. J. Carlson, I. lwasaki

Manganese and silica in nonmagnetic tailings from the direct reduction-magnetic separation step were so closely associated that no physical concentration methods were effective. Dilute sulfuric acid dissolved manganese and iron rapidly; manganese in the form of silicates was virtually insoluble in sulfuric acid solutions, thereby governing the maximum extraction attained by leaching. Autoclave leaching at elevated temperatures and at high oxygen pressures reduced the iron extraction to less than one tenth without affecting the manganese extraction. There was an indication that autoclaving solubilized the manganese silicates appreciably. Elimination of iron from leach solutions was carried out by aerating the solution in the pH range of 6.5-7; a platinum-calomel electrode pair provided a reliable indicator for the end point of iron removal. The purified leach solutions were free of interfering impurities for the recovery of manganese as metal, dioxide, or carbonate. Manganiferous iron ores of the Cuyuna Range, Minn., are too low in iron content to be directly useful as iron ores, and too low in manganese content to be termed manganese ores. Common methods of physical beneficiation such as gravity concentration and flotation have not been successful in upgrading this material. The R-N process, when applied to manganiferous iron ores,1'2 produces sponge iron by direct reduction of iron oxides, while leaving manganese as manganous oxide. From fine grinding and magnetic separation of the reduced ore, a tailing is produced which is relatively rich in manganese and low in iron content. The nonmagnetic tailing can readily be leached with acids and then further processed to recover manganese in various forms. In this way, two processes, neither of which would be an economic solution to the Cuyuna ore problem by itself, may be combined to produce two marketable products, thereby rendering the over-all process economically more attractive. This article reports on the results of a leaching study on the nonmagnetic tailings, both in a batch agitation vessel and in an autoclave; on the problems involved in the purification of leach liquors by aeration; and on the recovery techniques used to produce manganese metal by electrolysis, manganese dioxide either by electrolysis or by autoclaving, and

Jan 1, 1968

By Eric J. Jette

In thermodynamic studies of gas mixtures and liquid solutions, the respective problems have been greatly simplified by the use of two general limiting laws; Dalton's law of partial pressures and Raoult's law. It is generally recognized that these two laws have a common physical and chemical basis which may be stated as follows: The law may be expected to be strictly valid only for systems in which the different molecular species are so nearly the same in their physical and chemical properties that a molecule is unable to recognize whether its neighbor is one of its own kind or not. Positive and negative deviations from both laws are frequently encountered. The occurrence of negative deviations in both gases and liquids is ascribed to attractive forces which, in the more extreme cases, may be so large in magnitude and so highly specific in character as to lead to the formation of definite chemical compounds. Positive deviations in gases develop only at higher pressures where the intermolecular distances are so decreased that factors such as molecular size and shape, which ultimately become concerned with the repulsive forces, come into play. In liquid mixtures, positive deviations are generally considered as due to differences in the symmetrical (nonpolar) fields of force which surround the various molecular species and which are supposed to give rise to a tendency for each species to associate with its own kind and thus to "squeeze out" the other variety. Fundamentally this also involves the existence of repulsive forces between unlike molecules. If the fields of force are unsymmetrical (polar) a tendency towards compound formation results. Stated in more exact terms, strict adherence to the law means that the "activity" (or any adequate measure of this quantity) of a component in a mixture is a linear function of the molecular (or atomic) fraction of that component between the mol fraction limits 0 and 1. A positive deviation means that the activity is greater than corresponds to the law; a negative deviation that the activity is less. The deviations from Raoult's law have been fully discussed by many writers1

Jan 1, 1934

By E. L. Raymond

The effect of heat treatment on the microstructure and resultant notch-bar rupture life of ZNCONEL alloys X- 750 and 718 was studied. It was found that the primary effect of heat treatment in rendering these alloys notch-ductile is the elimination of any y' denuded zone adjacent to the pain boundaries. The mechanisms by which such a denuded zone can arise and be eliminated by heat treatment are discussed. InCONEL Ni-Cr alloy X-750 and INCONEL Ni-Cr alloy 718 are age-hardenable austenitic materials. Alloy X-750 is used for its corrosion and oxidation resistance and high creep-rupture strength up to 1500°F. Alloy 718 is used most effectively up to 1300°F. One of the most important areas in their development has been establishment of consistently good rupture properties, especially in the presence of a stress concentration, such as imposed by a notch. A desire to improve these properties has led to extensive studies of the effect of heat treatment on the micro structure of these alloys and their performance in stress-rupture tests. In earlier investigations"~ of INCONEL* alloy X-750, *INCONEL i s a Registered Trademark of The International Nickel Co., Inc. grain boundary carbide morphology was linked with stress-rupture properties. If, during heat treatment, the carbide MZSC was precipitated in the grain bound-ary in a cellular form, poor rupture properties re-

Jan 1, 1968

By W. W. Cotter, W. R. Clark

WEBSTER tells us the word "extrude" means to "force, press or push out; to protrude." As applied to the metal industry, the process consists largely of forcing plastic elements (plasticity usually obtained by preheating), through dies of predetermined profiles, into constant sections of considerable length and weight. Most of the "virgin" metals are quite malleable under this process, likewise many of the commonly used "alloys" in various industries, when basic elements are proportioned or combined within the natural laws and limits of good metallurgy. Several of the foundry alloys, both ferrous and nonferrous, together with some of the heat-treatable light metal mixtures, are decidedly weak and hot short at ordinarily plastic ranges, and consequently are troublesome or quite incapable of commercial extrusion. DEVELOPMENT OF PROCESS This process was conceived some time before 1800 and during its first century was employed almost entirely in making lead pipe, plumbing fittings and coating electrical cables. As a result of contact and experience with the lead industry and presses, Alexander Dick, of London, England, is credited with first having applied the principles of extrusion to brass, and in 1894 brought out a 500-ton horizontal press powered by hydraulics. A duplicate of this unit was imported by one of the Connecticut brass mills and was in experimental operation by 1900. During the first five years of operation, this press proved the value of the method to American industry, as it immediately revolutionized and converted the manufacture of brass rod from a 15-pass cold-rolling operation, with elimination of several intermediate anneals and cleanings, to an extrusion and a finishing draw. Likewise, ornamental brass and bronze moldings formerly cast and machined were produced in one squeeze on the extruder. The extrusion operation, being entirely that of compression, deforms the material without tensile stresses and can be used on delicate mixtures under heat, which cannot be hot-worked by straight hot-rolling or roller piercing. Base slabs of clock-brass strip were early in line of development or improvement, as were the brass bronzes (Naval brass, Muntz metal, manganese bronze, and others), popular as engineering materials for bolt stock, as well as structural shapes for marine and other mild conditions of corrosion. By 1910, American engineers undertook to design tube shell extruders, but were unsuccessful. The first World War began before fabricators could procure the more substantial designs of tube extruders produced in Germany; and it was not until the middle twenties that better models of the Universal extruders (double-actioned presses), equipped with hydropneumatic accumulator systems and other modern equipment, were available in the United States.

Jan 1, 1945

By E. D. Gardner

INTRODUCTION OIL shale deposits have been exploited in various countries throughout the world, but generally with government aid. The oil-shale industry of Scotland perhaps is the oldest and best-known; the largest was conducted in Manchuria by the Japanese during World War II as a source of liquid fuels for military uses. In general, foreign oil-shale deposits that have been exploited are much lower grade than those in the western United States. Considerable interest began to be shown in western oil shales in 1916; the peak of activities was in 1923. The Catlin operation, near Elko, Nevada, perhaps was the nearest approach in this country to an oil-shale enterprise on a commercial scale. Over 100 companies were formed, ostensibly for exploiting the oil shale; a large number of them, however, proved to be stock promotions only, which gave the embryo industry a black eye. The Bureau of Mines operated an experimental oil-shale retort plant near Rifle, Colorado, from September 1926 to June 1927 and again from April 1928 to July 1929, after which the plant was dismantled. By this time the East Texas oil fields had come in and the country lost interest in substitute liquid fuels. During World War II the Nation again became concerned about the magnitude of its petroleum reserves. Congress (April1944) directed the Bureau of Mines to build and operate demonstration plants to produce synthetic liquid fuels from coal, oil shales, and agricultural and other products; a five-year program was authorized. As a part of this program the Bureau of Mines has built, at Anvil Points near Rifle, Colorado, a retort plant and developed an experimental mine to supply the plant with oil shale. An important part of the mining work at Rifle is to devise methods and select practices for mining the oil shale on a commercial scale at the lowest practicable cost. The product to be mined has a relatively low value, a fact that must be kept continuously in mind. The combined aim of those in charge of the mining and those in charge of retorting is to demonstrate that the shale oil can be produced at a cost per barrel corresponding to the current quotation for crude petroleum -or at least very close to it. Plans call for an uninterrupted flow of broken oil shale from the face in the mine, through crushers, through the retorts and thence to the disposal dump. The disposal of the spent shale in the Rifle area should present no unusual problem. Mining research has consisted so far of paper studies of the general phases of the problem, determination of the widest span that the roof stone will stand safely unsupported, and drilling problems. Underground development has not proceeded far

Jan 1, 1947