Search Documents

By D. P. Morton

Since 1923, which closed the speculative era in the bituminous coal fields of the United States, there have been wide annual fluctuations in the national production of bituminous coal. These changes in annual output have been variously attributed to: (1) increased competition from petroleum products, natural gas and hydroelectric power; (2) lower unit consumption of coal; and (3) fluctuations in the general business level. The purpose of this paper is to measure, from a practical standpoint, the net effect upon the annual trend of bituminous coal production, and to give those who are interested a basis for estimating in advance the probable output of bituminous coal. It can readily be shown that changes in the level of general business affect the national production of bituminous coal more than does any other factor. Therefore it is necessary to use some standard measure of the relative business level for purposes of comparison. The Federal Reserve Board Index of Industrial Production offers the basis for such a measure.l This Index, a weighted composite of 81 different series, rests upon the averages of the years 1935 to 1939 as 100, and is presented graphically in Fig. I. Even a cursory examination of the chart will indicate a definite uptrend for industrial production over a period of years. This uptrend is due to at least two factors: (I) an actual increase in national population, and (2) a probable increase in the per capita consumption of goods. This means that there is no such thing as a fixed Normal, rather Normal is a variable, tending to increase from year to year. In order to measure the amount of annual increase in normal, the Index of Industrial Production must be studied in relation to its major components, Durable Goods and Nondurable Goods, Durable Goods are those made from the lasting materials such as iron, steel, other metals, lumber, stone, cement, clay, glass. Nondurable Goods are those for early consumption, such as foods, textiles, tobacco, chemicals, paper, gasoline, and goods made of leather and rubber. The purchase of Durable Goods may be postponed, but Nondurable Goods must be purchased currently unless the standard of living is lowered. The Federal Reserve Indexes of durable and nondurable goods are shown graphically, 1920 to 1939, on Fig. a (pp. 764-765 of ref. I). It is apparent that fluctuations in the production of nondurable goods are not nearly so wide as in the production of durable goods, and that the curve of Industrial Production (Fig. I) would fall between the two curves on Fig. 2. It would, however, seem logical that both curves should follow the same long-term trend, or that over a period of two to three decades the relative proportion of durable and nondurable goods, in periods of normal production, should be the same. It is neces-

Jan 1, 1942

By Norbert R. Morgenstern

INTRODUCTION An understanding of the role of water in controlling the stability of rock masses is central for a rational approach to the subject. The presence of water can hinder mining opera- tions in two ways: 1. excessive discharge 2. excessive pressure It should be noted that if the rock mass is very tight, excessive pressures can exist without large discharges. Alternatively, if abundant water is available and the rock mass is open, then substantial discharges can occur under quite small pressures. The problems associated with excessive discharge are usually well understood by the mining engineer. Vehicle mobility is inhibited, some areas are flooded and hence become inaccessible; at best, a costly nuisance exists. The methods of solving these problems are also well-known to mining engineers. They generally involve tapping the source of the excessive discharge and channeling it away in such a manner that any hindrance to the mining operation is minimized. The effects of water pressure on the stability of rock masses are less obvious and the following will be devoted solely to this aspect of the problem. The manner in which water pressures enter into the consideration of stability is made clear by an understanding of the concept of effective stress. THE CONCEPT OF EFFECTIVE STRESS The simplest mechanical model for the problem of rock slope stability consists of a rough, rigid block sliding down an inclined plane under the influence of gravity. This is illustrated in [Fig. 1]. The down-slope component of the weight of the block tends to produce movement which is resisted by the shearing force generated by friction along the base of the block. The shear stress per unit area inducing movement is

Jan 1, 1971

By R. H. Doremus

From measurements of carbide precipitation rates in a iron it was concluded that the carbides nucleated on dislocations in both strained and unstrained samples, except for the latter at lower temperatures and higher carbon concentrations, where there were more muclei than could form on the dislocations. The equation of Cottrell and Bilby for the segregation of atoms to dislocations was found to be inapplicable to this system. No satisfactory theory for the growth process is available. A study of the rate at which a second phase separates from solid solution can frequently reveal much about the mechanism of separation. There are still many features of the precipitation of carbon from a iron that are not understood, although this system has been examined extensively. To provide more insight into the mechanism of carbide precipitation in a iron, rates of this process were measured at different temperatures, carbon concentrations, and densities of dislocations in the iron. The concentra- tion of carbon in solution was followed from the height of the internal-friction peak; this height is directly proportional to the amount of carbon in solution and is not affected by the growing carbide particles. In this paper these rates are compared with those found by earlier investigators, and the mechanism of precipitation is discussed in light of these results as well as two earlier studies1, 2 and the electron microscopic work reported in the preceding paper. EXPERIMENTAL The amount of carbon in solution was followed by

Jan 1, 1961

By Charles P. Berkey, John B. Hastings

The reconnaissance of the Goldfield mining-district, describecl in this paper, was made in May and June, 1905, and, though this time was too short for a complete report, the work accomplished may serve as a basis for more thorough future research. Dr. Berkey has examined the rocks collected by me, and I am using his classifications. As a result of further field-work, and Dr. Berkey's examination of the rocks, this paper is an elaboration and correction of my views expressed in the Gold-$elm Sun, May 12, 1905. The sketch-map, Fig. 1, illustrates the geology of the Goldfield mining-district. Goldfield is an eruptive complex, consisting of alaskite (hinary granite), hornblende-andesite, hornblende-dacite, rhyolite, pyroxene-andesite, pyroxene-dacite (sometimes containing a small quantity of olivine), quartz-felsite, olivine-pyroxene-ande-site, and basalt. Considering this list to be arranged in the order of eruption, the age-sequence of the rocks conforms to Richthofen's law, formulated in 1868. From his observations in Europe and America, propylite, andesite, trachyte, rhyolite and basalt, occurring together, succeed one another. In a general way, the medium and the more acidic rocks precede the most basic—a result supposed by some to hare arisen from their position beneath the. surface, and due to a rude stratification by gravity in the original cooling magma during the older history of the earth, or to the same differentiation occurring during a quiescent (molten ?) period preceding eruption, being aided by the ease with which acidic rocks, mixed with water vapors, become fusible. In effect, the more basic and less re-

Jan 1, 1907

By I. Milton LeBaron

OPERATION of the phosphate flotation plant at the Peace Valley mine of the International Minerals and Chemical Corporation, Florida, began in the summer of [ ] 1942. Since that time several changes have been made in the flowsheet, with resultant increases in metallurgical results. Three flowsheets, together with the comparative plant results, are given in this paper, together with a discussion of the desliming circuit used for preliminary washing of the flotation feed. FIRST FLOWSHEET CHANGES Fig. I lists the essential units in the original flowsheet at the Peace Valley plant. The figures for tonnage and grade are average for a period of two months. Mineral Separation Airflow cells are used for both the fatty acid and the amine float. Three immediate difficulties presented themselves in the use of this flow sheet: I. Floating a maximum amount of phosphate in the rougher section to give good recovery sent a low-grade concentrate to the silica float, resulting in high costs for amine reagent in that section.

Jan 1, 1946

By Noah Fields Drake

During July and August, 1899, the writer took advantage of an opportunity of going to Shansi to gather some information concerning the geology and value of the already famous coalfields of that province. The long journey, mainly on slow river-boats, and the limited time at command, allowed only about ten days of work to be done in the coal-fields around Tsê Chou. The geologic structure and the rock-formations were found to be simple and quite regular, so that in that time the accompanying sketch-map (Pig. 1) was made, and a fairly good idea of the distribution of the coal and general geologic features was obtained. The map was made by measuring a base-line about three-quarters of a mile long, triangulating for principal points over the field, and filling in the details by rapid sketches. The few elevations marked on the map were taken with an aneroid barometer. Only a few of the great number of towns and villages that are within this densely populated area are shown; and the coal-mines indicated are not the only ones within the area, but the ones where most of the following information about the coal was obtained. The value of this coal-field was first clearly set before the scientific and commercial world by Baron von Richthofen,* who made a geologic reconnaissance of Shansi in 1870. Since that time the hostile attitude of the Chinese government and people towards foreigners and their enterprises has kept the coal-fields from being developed. But the last few years of rapid change in the conditions of China have at last apparently opened a way for the exploitation of this coal-field. The Peking syndicate, a joint English-Italian company, now has concessions from

Jan 1, 1901

By W. A. Cole, E. L. Derby, J. F. Wolff

Exploration of Lake Superior iron ores is done principally by drilling. The soft iron ores are churn drilled and the harder ores are diamond drilled. The churn drill used is the Mesabi type and its operation should be described as "water jetting." The drill rods are washed down by the combination action of the water jetting from the bit at the lower end of the rods and the churning motion given the line of rods. The water, which is forced down through the rods, comes up between the wash rods and the casing, bringing the choppings to the surface. It is caught in three or more barrels, each of which has a stoppered hole 8-10 in. from the bottom. These barrels are successively filled, allowed to settle, and drained to the hole, until the desired depth is drilled. The sediment from each barrel is transferred to a settling tub in which it is allowed to settle; the water is then drawn off and the wet sample is collected and dried. The number of barrels used depends on the character of the ore. For example, when drilling sandy ores, all the wash water is caught and settled for the proper length of time without refilling any of the barrels. Thus, the sediment held below the stoppered hole in any one barrel is not disturbed. The casing is kept as near the bottom of the hole as practicable to prevent the caving of the hole from jeopardizing the sample. While the casing is being driven down and the hole is being washed clean after casing, the return water is not run into the sample barrels. In exploratory work in the harder formations, where the diamond drill is used, the sample comprises both core and cuttings. The care given in handling and preserving the core depends on the importance that may be attached to certain characteristic strata in different formations. The following instructions for the care of core samples are issued by the Ogle-bay Norton Co. for diamond drill work done for them on the Gogebic Range of Michigan:

Jan 1, 1925

By H. I. Aaronson, S. Toney

When the component grains of .ferritic hicrystals of an Fe-1.55 pct Si alloy are disoriented through an angle "6 " about a conzmon [ll0] axis, the tendency for preferential growth of austenite crystals along the grain boundary during transformation at elevated temperatures is small when 11 deg, but increases rapidly at larger angles. This type of orientation-dependence indicates that grain boundary diffdsion promotes preferential growth along large-angle boundaries. Morphological differences between austenite crystals formed at small-angle [1101 and [loo] boundaries suggest that precipitate morphology can be dependent on the dislocation structure of the boundary. ThE morphology of precipitate crystals nucleated at a grain boundary can be significantly affected by the structure of the boundary.' The limited amount of experimental evidence available in the literature indicates that the morphological effects of boundaries made up of arrays of dislocations, such as subbound-aries and small-angle grain boundaries, are different from those of boundaries having essentially disordered structures, i.e., large-angle grain boundaries. On the basis of indirect evidence, it has been concluded that large-angle grain boundaries give rise to the formation of grain boundary allotriomorphs (crystals which nucleate at grain boundaries, and grow preferentially and more or less smoothly along them)2 in the proeutectoid ferrite and the proeutec-toid cementite reactions in plain-carbon steels, and apparently also in many non-ferrous alloys.' At small-angle grain boundaries in a plain carbon steel, on the other hand, ferrite crystals were found to take the form of primary side plates. Similarly, Guinie, loys. Primary sideplates formed at a subboundary with a constant orientation tend to be parallel to only one, or occasionally two matrix habit planes, and a marked change in the orientation of the boundary is accompanied by a change in the habit plane. Previous studies on the morphological effects of grain boundary structure were performed on poly-crystalline aggregates. Information on the disorien-tation of the pairs of grains forming the boundaries at which the various morphologies appeared in these specimens was largely either qualitative or semi-quantitative. Precipitate morphologies accordingly could not be accurately and systematically correlated with grain boundary structure, and thus theories which have been proposed for the various morphological effects could not be satisfactorily tested. This investigation was undertaken in an attempt to remedy these deficiencies by studying the morphological effects of grain boundary structure with a method in which the boundaries are formed by matrix grains whose disorientations are known and controlled with reasonable accuracy. EXPERIMENTAL PROCEDURE The crystallographic requirements of this study were fulfilled by means of oriented bicrystals of silicon-iron. Disorientation of the component ferrite crystals was carried out about common, major crystallographic axes through angles ranging from 1/2 to 44 deg. The silicon content was low enough SO that the bicrystals could be partially transformed to austenite by heating to elevated temperatures. The silicon-iron used had the following initial composition: 1.55 pct Si, 0.04 pct C, 0.0031 pct N, 0.17 pct Mn, 0.020 pct S, and 0.002 pct P. The alloy was obtained in the form of 0.036-in. sheet. The procedures employed to prepare seed crystals in strips of this sheet, to reorient the seeds, and to grow them into bicrystals are essentially those described by Dunn and Nonken and aynes." The characteristics of the bicrystals are given in Table I. The "bicrystal type" indicates the crystallographic plane parallel to the broad faces of the strip in both grains and the crystallographic direction which was parallel to the long edges of the strip in both grains prior to disorientation. The angular disorientation of the grains, 8, which was performed about the direction normal to the plane of the broad faces of the strip, was measured between the [ 00l] directions. Orientation of the grain boundary, , was taken as the angle between the plane of the grain boundary and a plane containing the axis of disorienta-

Jan 1, 1962

By R. M. Goldhoff, J. W. Spretnak

IN connection with establishing the mechanism by which boron enhances the hardenability of heat treatable steels, this research work has been undertaken. Spretnak and Speiser1,2 indicated the need for studying high temperature effects in boron steels and, chief among these, the possible nonhomogeneous distribution of boron in iron grains. The occurrence of this effect may be of significance in explaining the mechanism of enhancement of hardenability by boron as well as in explaining some of the observed characteristics of boron steel behavior. Primarily, then, this work was undertaken a) to establish whether or not boron is adsorbed in ? solid solutions, b) to determine the nature of any such adsorption effects, i.e., whether it is positive or negative as well as its temperature coefficient, and c) to establish the magnitude of any such effect. While past literature on this specific subject is rather sparse, a number of authors have postulated that the observed temporary loss of hardenability as well as the occurrence of the characteristic boron constituent in these steels is due to the nonuniform distribution of boron in austenite.3-0 Experimental Techniques Attempts to obtain direct evidence of grain boundary effects in boron steels have been unsuccessful, both by using the technique of Chalmers' in which small concentrations of solute made radioactive by irradiation are detected by autoradiographic means, and by means of studying cleavage fractures with the electron microscope.8 The present study attempts the design of experiments to measure the effect of boron on properties which might be subject to variation because of grain boundary effects. A study of the theoretical aspects of grain growth indicates that such studies may be pertinent. Another valid type of experiment involves the measurement in polycrystalline materials of properties whose values depend on the bulk of the grain, being negligibly influenced by grain boundaries. One such property is the lattice parameter measured by X-ray diffraction. The value of the lattice parameter reflects the average conditions which obtain over a relatively large number of atoms in a fixed crystalline lattice, and is therefore mainly dependent on bulk grain material. Measurement of lattice parameter variation over the austenite range of temperature in iron with and without boron should give evidence of concentration variations in the bulk grain material if adsorption effects are significant. Finally, use is made of the Grange and Garvey3 metallographic test for boron in which a characteristic boron constituent can be developed in austenite grain boundaries. The very occurrence of this phenomenon suggests grain boundary enrichment of boron and a study of the occurrence of this constituent and its varation with austenitizing temperature should help to detect grain boundary effects. Materials One lb ingots of pure iron, an Fe-B alloy, an Fe-C alloy, and an Fe-C-B alloy were prepared. The melting technique included an initial melting of electrolytic iron under vacuum followed by remelting under hydrogen and, finally, by melting under argon with the addition of alloying elements. Each ingot was surface machined between meltings. A quantitative spectrographic analysis was obtained on the pure ingot and, in addition, oxygen, nitrogen, and carbon were determined by the vacuum fusion method. The results of these analyses are given in Table I. Semiquantitative spectrographic analyses were performed on the alloy ingots, while quantitative determinations of the alloy additions were obtained. These analyses are shown in Table 11. The cast ingots were subjected to the following sequence of fabrication treatments: forging to 5/8 in. bars, swaging to 0.300 in. rounds, drawing to 0.025 and 0.010 in. wire. Portions of each ingot were retained in the swaged condition for experimental use. For certain portions of the work typical commercial steels were used. These materials were supplied by the Republic Steel Corp., Canton, Ohio, and correspond to AISI 8640 and AISI 86B40 compositions.

Jan 1, 1958

By W. G. Lidman, H. J. Hamjian

' I HE fabrication of many materials from powders involves a sintering process. A mass of powder will sinter because of the excess free energy over the same mass in the densified state caused by the higher total surface area of the powder. An understanding of the kinetics and mechanism of sintering should assist in improving the properties of such materials. The present investigation conducted at the NACA Lewis laboratory deals with the sintering of chromium carbide. Dry sintering (sintering at a temperature below the melting point) was divided into two stages by Shaler:' the first stage, during which the particles preserve much of their original shape and the voids are interconnected, and the second stage, during which densification occurs and the pores are isolated. The mechanism of forming interfaces between particles, or welding together of particles, has been investigated by Kuczynski2 and may be described by any one or a combination of the following mechanisms: viscous flow, evaporation and condensation, volume diffusion, or surface diffusion. The mechanism by which pores are closed or eliminated (densification) during sintering, is of interest. Grain growth observed during sintering may be attributed to the variation in the surface energies of individual grains, causing some grains to grow at the expense of others. Grain boundary migration occurs presumably by a diffusion process, therefore the rate of grain growth would be expected to increase exponentially with increasing time and temperature. Thus, for practical sintering times of less than 1 hr, a certain minimum temperature may exist at which major structural and property changes will occur. Densification and kinetics of grain growth during sintering under pressure of chromium carbide were investigated to provide additional information which will aid in describing more accurately the sintering process and the mechanisms involved. This material was selected for this study because of the current interest in high strength, oxidation resistant refractory materials, such as carbides, which are sintered to produce solid, dense materials from powders. Sintering under pressure is a process where the heat and pressure are applied to the compact simultaneously, specimens for this work were prepared by sintering under pressure at different temperatures and for various time periods. Experimental Procedure Preparation of Specimens: Chemical analysis of the commercial chromium carbide used in this investigation was as follows: Cr 86.19 pct, C 12.14 pct, and Fe 0.2 pct. X-ray diffraction powder patterns gave characteristic diffraction lines of Cr3C2 crystal structure. Powder particle size was determined microscopically and the average initial particle size was 6 microns with 85 pct between 2 and 10 microns. Specimens sintered under pressure were formed in graphite dies3 heated by induction. Sintering temperatures were measured with an optical pyrometer by sighting into a 3/8-in. hole drilled 1 in. deep at the midsection of the graphite die. A load of approximately 1 ton per sq in. was applied to the powder. The die assembly was heated in 20 min to the highest temperature (2500°F') at which no increase in grain size could be observed, and less than 2.5 min were required to heat from this temperature to the maximum temperature (3000°F). Sintering temperatures and times for the specimens of this investigation are indicated in Table I. Analysis of Specimens: Specimens polished with diamond abrasives were etched to reveal the grain boundaries with a 1:1 mixture of 20 pct potassium hydroxide and 20 pct potassium ferricyanide heated to 160°F. Representative areas of each sample were photographed at 1000 diameters. The largest diameters of all well-defined grains were measured, but only the measurements of 15 of the largest grains were averaged in order to determine an index of grain size on the assumption that they were among the first to begin growth. Densities were determined from differential weighing of the samples in air and water. The reported density values are considered correct within ±0.01 g per milliliter. Results and Discussion Metal compacts have exhibited grain growth when sintered at temperatures about two-thirds of the absolute temperature of their melting point.' Grain growth also occurs during the sintering of chromium carbide and is illustrated by the micrographs shown in Fig. 1. These micrographs were prepared from specimens sintered for 90 min at temperatures ranging from 1371°C (2500°F) to 1648°C (3000°F). Average grain size and density measurements of specimens investigated are presented in Table I. The relationship between grain size and sintering tem-

Jan 1, 1954

By Everett H. Graff, Ray H. Misener

THE Sol de Oro mine is in the province of Nazca, 487 km. southeast of Lima, and 60 km. inland from the coast at an elevation of 1200 m. above sea level. From Lima the mine may be reached in 8 hr. by automobile; 472 km. from Lima to Nazca over the paved Pan-American Highway and 15 km. from Nazca to the mine over a good graveled road. The trip from Lima can also be made in 2 hr. via the Faucett Air Lines which make two stops weekly at Nazca. The [Compania] Aurifera Nazca, owning and operating the Sol de Oro mine, was organized in Lima in 1930 by a group of prominent Peruvian mining men, including Ing. Carlos Alvarez Calderon, Dr. Alfredo Alvarez Calderón, Ing. Hector Boza, Ing. Jorge Félix Remy, Ing. Eulogio Femandini, Sr. Fernando Wiese, and Sr. Julio East. The nine claims in the Sol de Oro group owned by the company comprise an area of 52 square kilometers. Development of the property was not started until 1932 and only then under adverse conditions, owing to lack of transportation facilities. Mining machinery and other supplies could be taken as far as Ica by boat and railroad, but to transport them over the 180 km. of hot, sandy desert from Ica to the mine was a problem. There was no road in those days and only a few of the most venturesome truck drivers cared to contract the hauling. Another problem the company had to face was that of securing adequate labor. The Sol de Oro is in an agricultural region, and was forced to look to the near-by cotton plantations for men. Experienced men were imported from the "sierras," but they did not stay. The men are accustomed to high altitudes and cold climate and cannot easily acclimate themselves to the hot and arid coastal region. As a consequence the company has been forced to hire the inexperienced local laborers and train them for mining. The company has established three separate camps at the Sol de Oro property. Each is approximately one kilometer from the other and connected by auto road. The upper mine camp consists of living quarters for 300 workmen and their families, a general mine office, carpenter shop and timber-framing shed, compressor house, drill-sharpening and drill-repair shop, first-aid station, time office, school and store. At the central or "empleados" camp there is a 200-ton cyanide plant, general offices, warehouse, powerhouse, shops, laboratory, hospital, school, guest house, an 18-room hotel for the single staffmen, and 12 completely modern five-room cottages for the married staff employees. At the lower camp are living quarters for 200 workmen and their families, two general stores, a school and a small theater. Below this camp, along the river, are the company wells and pumping plant supplying water for mine, mill, and camp uses.

Jan 1, 1945

By James J. Norton, Lincoln R. Page

Effective methods for determining grade and reserves of pegmatites in advance of mining have been developed in recent years. When intensive work began on the economic geology of pegmatites during the early years of World War II, it was widely believed that grade and reserves could be estimated only in a most general way. The literature indicated that not all pegmatite deposits are unpredictable, but statements emphasizing unpredictability and irregularity seem to have been more widely accepted. Many standard references reflect the prevailing opinion that minerals are unsystematic in their occurrence in pegmatites. Pegmatites have been de- scribed as "notorious for their irregular structure," and minerals within pegmatites as "irregularly distributed," "irregularly disseminated,'' of "erratic occurrence," "proverbially erratic in distribution," "characterized by extreme irregularity in size and distribution of the essential minerals, and variety and proportion of the accessory minerals, and "spotty."

Apr 1, 1956

By N. B. Pilling

THE development of a proper treatment for shells in connection with war contracts has brought to our attention the fact that the temperature of the liquid bath in which steel is quenched has a decided influence on the speed of cooling in the case of some liquids and very little in the case of others. Widely different physical results have been obtained by the use of water spray, water immersion, and oil immersion and further experiment has shown that the quenching effect of water used as a spray or an immersion varies greatly with the temperature of the water. The present experiments were undertaken with the idea of obtaining information of a quantitative nature regarding the quenching properties of a number of liquids used commercially in hardening steel. The general features of such cooling media are common knowledge and in the literature may be found records of numerous attempts to evaluate the cooling power of a liquid when used as a quenching bath. Much, if not most, of the data given on this subject is in the form of a simple statement of the time required for a certain heated mass to cool between two arbitrary temperatures when immersed in the liquid, quite regardless of the path of the temperature change. Our own purpose has been somewhat different. We have attempted to isolate that property of these. liquids having to do with their ability to absorb heat rapidly, as distinct from the behavior of a considerable mass when exposed to different thermal environments. More specifically, from the data obtained through autographically recorded cooling curves of a small standard mass quenched under various conditions, we have tried to analyze the mechanism of heat absorption by the several liquids, measure the changes in its rate as a function of the temperature of the surface of transference, and ascertain the influence of the temperature of -the liquid itself upon both.

Jan 9, 1919

By Howbert Van Dyne

THE Presidio mine of The American Metal Co. of Texas is situated 45 miles south of Marfa, Texas, a town on the Southern Pacific R. R., and lies approximately 20 miles north of the Mexican border. Communication with the railroad is maintained over a state highway. All supplies for mine and mill are hauled in by truck from Marfa and precipitates and concentrates are freighted to the railroad by the same means and shipped to Selby and El Paso, respectively. The mill is at the town of Shafter, 1 mile from the mine and at approximately 350 ft. lower elevation. The ore is conveyed to it by an aerial tramway which requires practically no power on account of the difference in elevation. The mill is a countercurrent decantation cyanide and gravity concentrating plant of 200 tons daily capacity. Coarse and fine crushing are done at the mill. Two near-by shallow wells in the bed of Cibolo Creek furnish an abundance of water. Power is generated for the mill and town by a Diesel engine plant.

Jan 1, 1930

By J. S. Harris

AS a result of the study of social problems to which so much thought has been given in this country and Europe in the last half century, many employers of labor have come to think that some provision should be made for their workingmen in case of injury. There has been a growing tendency so to administer the laws governing industrial pursuits in these countries as to add self-interest on the part of capitalists, to the plea urged by humanity, that every possible care should be taken to guard the workers from accident; but as no care can guarantee immunity, there is a necessity to supplement these precautions by some method of providing pecuniary aid that shall be available when disabling accidents do occur. It was once a favorite idea of theorists on political economy, that in the ideal state of society every man should take care of himself, and that the less care or control there was assumed by any man over others' private affairs, the better; but this gospel of selfishness has had its day, and it is now generally recognized that in the existing state of affairs the stronger and richer cannot escape the duty of being to some extent, the keepers of their less fortunate brethren ; and, on the other hand, that an assumption of care for them involving to some extent an exercise of authority, is not a thing to he necessarily and always resisted. Out of these convictions, many efforts for the amelioration of the condition of workingmen have grown—which or one result have produced various plans which combine the con-

Jan 1, 1884

By J. L. Lamon, W. Crafts

Study with the electron microscope of the carbides in vanadium-chromium-molybdenum steels after tempering up to 1000 hr at 600 teelsto 1400°F confirmed that alloy carbides are formed at the secondary hardening temperature by decomposition of the plate-like iron carbides. It was also demonstrated that vanadium carbide persists as much smaller particles than do chromium- or molybdenum-bearing carbides. Conditions conducive to the formation of fine vanadium carbides are indicated to be favorable for high temperature strength. IN order to determine the effects of long exposure at high temperatures on vanadium-bearing steels, a survey has been made of their hardness and carbide structure. The behavior of carbides in the tempering of martensite was studied by X ray diffraction and electron microscope examination of electrolytically extracted residues in greater detail than in an earlier investigation.' A group of steels with about 0.25 pct carbon and containing chromium up to 5 pct, molybdenum up to 1 pct, and vanadium up to 1 pct was either quenched or annealed and then tempered for peri- ods of up to 1000 hr at 600° to 1400°F. Their hardness after tempering agreed with the Hollomon and Jaffe2 relation of equivalency of time and temperature, and with the degree of secondary hardening predicted from composition. Further, the appearance of the carbides indicated that the time and temperature equivalency relation was also applicable to the degree of carbide development. The mechanism of the tempering of martensite was demonstrated more clearly than in the earlier study. It was confirmed that carbides develop from martensite as poorly defined plates of the Fe2C type carbide followed by thickening of the plates with a transition to Fe,C. Finally the plate structure deteriorates into a lacy mass from which alloy carbides emerge as chunky particles that grow slowly with further increase of tempering temperature. Vanadium carbide derived from tempered martensite was found in characteristically small particles that tended to grow very slowly. The addition of chromium or molybdenum to a steel with predominant vanadium carbide tended to introduce carbides of a chromium- or molybdenum-bearing type having a somewhat larger particle size. The Cr,C, type carbide particles were larger than those of the V,C, type and somewhat smaller than the carbides in steel containing both Cr,C and M,C. Similar observations were made of the carbides in the pear lite of annealed steels. It appeared that high temperature properties would be benefited by the retention of the fine carbide particles that result from a balance of composition and heat-treatment designed to produce a maximum amount of vanadium carbide. Procedure: The steels used in the investigation were made with a base of Armco iron in a high-frequency furnace at the Union Carbide and Carbon Research Labs., Inc. The steels were deoxidized

Jan 1, 1951

By W. P. Sykes

IN CONNECTION with a study of tungsten steels, Honda and Murakami1 reported an investigation of the system iron-tungsten. This report included a tentative equilibrium diagram, photomicrographs of various alloys in the series, and qualitative measurements of hardness and magnetic properties. The present investigation originally had as its object the study of the hardness and tensile properties of a series of carbon-free iron-tungsten alloys. But, as the work progressed it became evident that the system possessed other features of interest, so the scope of the investigation was enlarged. MATERIALS The iron powder used in preparing the alloys was obtained as follows: Iron oxalate was precipitated from a ferrous-sulfate solution by the addition of a solution of oxalic acid. This oxalate, after thorough washing, was ignited to iron oxide, which after reduction in hydrogen at about 1000° C. yielded iron powder containing but about 0.2 per cent. iron oxide and about 0.005 percent. carbon. Tungsten metal in the form of powder, such as is used in the manufacture of filaments for incandescent lamps, was the other constituent. This material analyzed 99.8 per cent. tungsten and contained no carbon, The metal powders, in the desired proportions, were mixed by tumbling and formed, under pressure of 20 tons per sq. in., into rods 3/8 by 3/8 by 10 in. To form the alloys without contamination, sections of the pressed rods were placed on alundum slabs and heated in an alundum tube wound with a tungsten resistor and packed in heat-insulating material. While the resistor was heated, a stream of hydrogen was continually passed through both the tube and the case containing it. The tungsten winding on the tube, as well as the material heated within the tube, was thus protected from oxidation. Such a furnace will operate constantly

Jan 2, 1926

By John Griffen

The modern anthracite breaker or washery uses almost exclusively a wet method of preparation, which requires, roughly, 1 gal. of water per minute per ton of production per day. The entire anthracite industry uses about 320,000 gal. per min. of water for this purpose or 800,000 tons of water per day. As this water leaves the breakers, it contains fine solids—coal, slate, pyrite, and clay—and is then called silt or slush; as slush is the term most commonly used, it will be employed throughout this paper. The solid content of the slush will be referred to as solids. In the earlier days of anthracite mining, little coal was washed, less crushing was employed, and virgin coal was mined exclusively. As a result, the slush problem was not acute because of the relatively small quantity and the coarseness of the solids. Such slush as was produced could usually be easily impounded and retained or could be discharged into streams without any appreciable pollution being apparent. The character of the fine waste from the breakers changed materially as its quantity increased until now about 40,000 tons of slush solids are produced daily. Second mining and robbing operations materially increased the quantity of fine solids delivered to the breaker in the mine car. The demand for chestnut, stove and egg sizes, to the exclusion of grate, steamboat, and lump sizes, requires finer crushing of the mine-run coal with a consequent increase of fine solids in slush. The use of rice and barley sizes removed a considerable tonnage of coarser solids from the slush but left great quantities of fine solids difficult to retain completely, and to store, and long considered of no possible fuel value. Despite the efforts of the coal operators, the slush solids have found their way into the streams causing, in some cases, serious pollution. The Water Supply Commission of Pennsylvania published, in 1916, a report on Culm in the Streams of the Anthracite Region,' from which the following is taken: About 40,000,000,000 gal. of water carrying 10,000,000 tons of fine culm are discharged into the water-courses direct, flushed into the mines, or disposed of by various means on the surface. The extent to which the very small sizes of anthracite have been deposited in the rivers draining the coal fields is made evident by the fact that over a quarter of a million tons are recovered annually from the river beds by coal-washing operations.

Jan 1, 1922

By C. Y. Wang

China now leads the world in antimony production, having contributed during recent years something over 60 per cent. of the world's production. The history of the antimony industry of China dates back to 1897 when the Tai Shing Co. was formed, under contract with the Hunan Bureau of Mines, for the smelting of the ore to crude; and in 1908 the Wah Chang Mining & Smelting Co. was formed for the smelting and refining of the ore and crude to regulus. The writer was then asked to take charge of the erection and control of this first plant for regulus production in China and has, since then, been more or less connected with the antimony industry in this country. This paper contains the results of many years' experience in connection with the Wah Chang Mining & Smelting Co., Changsha; the Pao Tai Mining & Smelting Co., Wuchow; the Loong Kee Smelting Works and the To-Cheng Smelting Works, Hankow; as well as information gathered from various other small smelters, scattered in different parts of the Provinces of Hunan, Hupeh, Kwangsi, and Kwangtung. An idea of the growing importance of regulus production in this country can be gleaned from the fact that, within a period of about 8 years, the export of regulus from Hunan alone jumped from 3 tons in 1908 to about 6000 tons in 1915; that a production of about 23,000 tons of regulus per year could easily be effected from all the smelters, as tabulated below, most of which were erected a year or two ago under the stimulus of the war booms, if the price at Hankow were to stay somewhere about $900 (Mexican) per ton, half of what it was at its height, thus enabling the utilization of ores from the hinterlands of the provinces; and even under the present ruling of prices and the closing of the less favored smelters, the production of regulus should not be less than 12,000 tons per year.

Jan 1, 1919

By I. A. Lesk

The various materials utilized in the construction of integrated circuits, and the resultant materials interfaces, are discussed with emphasis on a materials system that is compatible with all types of integrated circuits and minimizes the number of different interfaces. Problems with interfaces may originate in the silicon, on its surface, and between other materials within the integrated-circuit package independent of the silicon. ThE difference between integrated-circuit theory and practice may generally be spelled out in terms of the difficulties in fabricating a desired structure. There are, of course, problems in forming the requisite materials, of the necessary composition and geometry, where needed. A distinct class of problem, however, is associated with interfaces— generally between different materials, but occasionally between regions of the same material. We require that each interfacial system perform its proper electrical, mechanical, and thermal function, and do so in an unchanging manner with time under the most severe operating conditions. In a practical sense, we deal in nonideal systems, such that it is generally not possible to form an interface exactly the way it was intended, even if we allow for a knowledge of the practical limitations of the fabrication system. Another way of looking at this situation is to realize that, when we form a group of interfaces under apparently the same experimental conditions, there are often differences of important consequence between them. Very high-magnification pictures, such as are obtained by an electron microscope, reveal fine structure that often differs over the area of a given sample, as well as from sample to sample. Low-magnification pictures look better, but don't eliminate the problem. The trend towards integrated circuits, and away from circuits fabricated utilizing separate components, is very strong in many areas of electronics. A typical silicon monolithic integrated circuit, still in place in the wafer on which it was fabricated, is shown in Fig. 1. The increased reliability which is being experienced through the use of integrated circuits can, to a large extent, be credited to the reduced complexity of the interface system that is present in the electronic system. A glance at Fig. 1, however, with all of its epitaxial and diffused p-n junctions, and interconnect system, shows that interfaces have been far from eliminated. Fig. 2, depicting a schematic cross-sectional view of a (partial) typical integrated circuit, illustrates in detail the numerous interfaces that occur in this type of structure. Besides the individual circuit elements, there are interfaces for isolation, and, Fig. 3, even a crossover requires a series of interfaces. What has been accomplished, however, irrespective of whether or not the total number of interfaces in the circuit is increased or decreased, is that the variety of interfaces is very much reduced. This is because there are fewer materials involved. Since the expense incurred in an R & D program to improve reliability is pretty much directly proportional to the variety of interfaces involved, it is economically advisable to work with integrated circuits for highest reliability. That is not to say that circuits built using standard components could not be made as reliable as integrated circuits, but that the expense involved because of the more complex over-all interface system would be much greater. Although electronic performance utilizing integrated circuits with all silicon elements (i.e., transistors, diodes, resistors, capacitors) is adequate for many applications, there are numerous instances where thin-film passive elements must

Jan 1, 1965