Search Documents

By Jr. Ensign C. O., J. W. Trammell

The two principal methods of room-and-pillar mining practiced at White Pine make it important to predict variations in the thickness and rock types of a stratum called the upper sandstone. In full column mining, the nearly barren upper sandstone occurs between two ore horizons (called upper shale and parting shale, respectively), and is mined as a part of the ore column. In general, full column mining is not practiced where excessive upper sandstone thickness causes full column ore grade to be substantially lower than parting shale ore. In parting shale mining, the upper sandstone forms the mine roof. Difficulty in predicting upper sandstone character arose because the extent and directions of its variations were not apparent in the property's diamond drilling, in which holes are spaced on 1000-ft centers. A study of sedimentary features, undertaken to improve the predictability of trends in the upper sandstone, led to an interpretation of the sedimentary environment in which the sandstone was deposited. Ripple marks, mud cracks, and cross-bedding, as well as other, less well known features, such as channel casts, flute casts, and current crescent casts, were mapped or recorded. These data, coupled with the knowledge of regional facies changes gained from studying drill core, show that the upper sandstone was deposited by a series of streams flowing northeastward over the underlying parting shale. Deposition of the lowermost bed of the upper sandstone, near the ancient shoreline, was locally preceded by erosion of the parting shale, and the greatest thicknesses of sandstone are found in channels scoured out of the parting shale. Awareness of the rather strong linear trends in the upper sandstone makes it possible to project continuous areas of thick upper sandstone through apparently isolated "highs" in the upper sandstone thickness contour map, which is based on drill-hole information. Since local exceptions to general stratigraphic trends exist, a method was also needed for esti- mating, in detail, the thickness and degree of shali-ness of upper sandstone forming the roof in active parting shale mining areas. Because locally the parting shale was thinned by erosion during the deposition of upper sandstone, parting shale thickness is inversely proportional to upper sandstone thickness. Utilizing information taken from short drill holes into the roof, curves were constructed for the correlation of parting shale thickness (measurable in the mine) with the upper sandstone total thickness, as well as the thickness of its basal member. The White Pine mine is situated in Ontonagon County, approximately 6 miles south of Lake Superior, in the Upper Peninsula of Michigan (Fig. 1). The orebody mined by White Pine Copper Co. occurs in the lowermost 20 to 25 ft of the Nonesuch formation, a series of middle- to upper-Keweenawan shales, siltstones, and sandstones. This paper discusses the solution of problems in ore grade control and mine planning arising from the presence of an essentially barren sandstone stratum within the orebody. THE OREBODY AND MINING TYPES A brief description of the orebody and mining methods is necessary to show how the upper sandstone affects mine planning and grade control. In the mine, the cupriferous zone of the Nonesuch shale is divided into three major portions, as shown in Fig. 2. Lying conformably on top of the Copper Harbor formation (or "lower sandstone") is the lower part of the orebody, the parting shale. The parting shale is overlain by the upper sandstone. On top of the upper sandstone, the basal portion (8 ft) of the upper shale is quite similar to the parting shale. Both the upper shale and parting shale are divided into a number of smaller stratigraphic units, each having a characteristic copper content, as shown by the histogram of Fig. 2. Other authors1'3 have dealt in detail with the stratigraphy and mineralogy of the orebody. However, in this article, we are concerned with the major subdivisions only, and it will suffice to note the low copper content of the upper sandstone, shown in Fig. 2. At present, two types of room-and-pillar openings are created in the orebody. In one type, called parting

Jan 1, 1964

By M. J. Pool

The partial molar heats of solution in liquid tin of cadmium, silver, tellurium, and zinc have been measured at 655°. 700°, and 750°K by liquid-metal solution calorimetry. Silver, cadmium, and zinc are endothermic at these temperatures while tellurium is exothermic. Only the heat of solution of silver depends on composition while all four elements show a temperature-de pendent heat of solution. The heat of solution of tellurium is constant up to 0.6 g-at. pct, becomes increasingly more exothermic, and reaches a limiting value at 1 g-at. pct Te. The limiting value has been used to calculate the heat of formation of SnTe at 750°K. The heat effects associated with the dissolution of the compounds Ag2 Te, CdTe, and ZnTe in liquid tin were measured at 750°K. These values are cotnOined with the measured hat effects at 750°Kfor silver, cadmium, tellurium, and zinc to detertrline the heats of formation of the telluride compounds. Cadmium lelluride exhibits a heat of dissolution which has a compositional dependence. THERE is a considerable amount of interest in the compounds of tellurium because of their electronic properties. Both cadmium and zinc tellurides are thermoelectric materials and considerable work has been done on their electronic properties but a limited amount of data is available on their ther-modynamic properties. This work was undertaken to elucidate the heat of formation data on cadmium and zinc telluride. Since both cadmium and zinc are in Group II it seemed to be of interest to compare the values obtained for them with the heat of formation of a Group I telluride. Silver telluride was selected for this comparison. In the course of the work it was also possible to determine the heat of formation of tin telluride and therefore to make a comparison of some of the Group I, 11, and lV tellurides with the metallic elements silver, cadmium, and tin being in the same period. There is also a great deal of interest in the energetic changes which occur upon addition of solute elements to a common solvent. This investigation provided an opportunity to study the partial molar heats of solution of silver, cadmium, tellurium, and zinc in liquid tin. The partial molar heats of solution are of theoretical interest because solute-solute interactions are a minimum in dilute solutions and application of solution models is simpli- fied. In order to complete the analysis of solute-solute and solute-solvent interactions the temperature dependence of the partial molar heats of solution was also measured. MATERIALS AND EXPERIMENTAL PROCEDURE All materials were of the highest purity available. The silver, zinc, cadmium, and tellurium were obtained from American Smelting and Refining Co. and were reported to be 99.999 pct pure. The silver telluride, zinc telluride, and cadmium telluride were obtained from Atomergic Chemetals Co., a division of Gallard-Schlesinger Chemical Manufacturing Corp., and were electronic-grade material of 99.999 pct purity. Tin used for the solvent bath and for calibration was obtained from the Vulcan Manufacturing Co. and was reported as being 99.99 pct pure. The liquid-tin solution calorimeter used in this work is similar in principle to the differential twin-type calorimeter described by K1eppa.l Two of three identical calorimeter wells are used together during any set of experiments, one well being active and the other being passive. The wells are positioned 120 deg apart in an aluminum calorimeter block. Each well contains a multijunction thermopile and a Pyrex test tube to hold the liquid metal bath. Forty-eight of the thermopile junctions are distributed over the surface of each calorimeter well adjacent to the test tube and serve to integrate the heat effects occurring. The other forty-eight are next to the aluminum calorimeter block. The thermopiles for the three wells are connected differentially so that any change in temperature at the outer junctions (which will be the same for both wells because of the high conductivity of the aluminum block) will oppose for the two wells and result in no shift of the zero. The electrical output represents the true temperature difference between the two reaction vessels. A reaction occurring in the active well gives a comparison with another body of very similar thermal properties. In this way, any spurious heat effects due to slight temperature drifts within the entire calorimeter block are eliminated. The output of the differential thermopile goes to a dc amplifier with multiple ranges of from * 10 pv to 1 30 mv. The output of the amplifier is then fed into a Leeds and Northrup strip-chart recorder. The adiabatic temperature change is then calculated using the technique of Howlett, Leach, Ticknor, and ever.' The aluminum calorimeter block is contained in a cylindrical furnace with main and control heaters

Jan 1, 1965

By W. Blake McCullogh

It is often written that the purpose of any mining operation is to produce efficiently, safely, and profitably, and always to search for more efficient, safer, and more profitable methods. To provide for continual improvement, an attitude that is not only reasonable but also imperative, there is an obvious need for a high standard of competence among the ranks both of supervision and of those being supervised. It naturally follows that, to achieve this standard, planned training in every level of an organization is a definite necessity. There are many factors involved in the need for training, and the scope of a program is influenced by answers to such questions as: "What is the geographic location of the project?" "What are the duties of each job?" "What is the source of the working force and supervision?" "What are the hiring standards for various jobs?" "What is the availability of trained personnel?" "What is the availability of outside training facilities?" The approach in this chapter will be to consider a need for a maximum of training, and it may be applied by the reader to whatever extent is considered necessary in each individual situation. 14.2-1. Administration. It is a basic responsibility of every supervisor at all levels to train those who work for him. However in a very extensive training program, which involves supervisors and the working force, includes both compulsory and voluntary participation, uses outside and in-plant methods, and where the increasing complexity of jobs requires more specialization, the establishment of a training department is definitely war- ranted. This will consist mainly of instructors for related classroom training and preparation of manuals, etc., and the necessary clerical help. A training staff does not relieve the various departments of their responsibility to train, but it does have facilities, experience, and contacts that are inval-

Jan 1, 1968

By John T. Eash

DURING the course of the war the supply of tin in this country has steadily decreased and a continued effort has been made since the beginning of the emergency to use alloys that are either tin free or contain appreciably lower quantities of it. Even with the use of emergency materials, the tin supply has become particularly acute, and it is estimated that after recovery of the far eastern mines probably one to two years will be required before our normal annual supply is attained. One of the major tin-consuming fields is the bronze industry. Recommendations were made several years ago by the War Production Board toward the use of bronzes of lower tin content and manganese bronze and yellow brass for the customarily used tin-bronze alloys. The substitution of 88-5-5-2 copper-nickel-tin-zinc for composition G received considerable attention before the war, and consequently this alloy and modifications of it have been adopted for some current structural and pressure castings requiring high mechanical properties. Another of the commonly used bronzes is the 10 per cent tin, 10 per cent lead copper alloy for heavy-duty bearings. It has been known for some time that about 2.5 per cent nickel could be substituted for an equal amount of tin with retention of equivalent casting and tensile properties; however, it was desirable that a still greater conservation of tin be made. Consequently the present paper deals with the development of an alloy of low tin content that could be used for bearings. SELECTION OF COMPOSITION While the final criterion of the suitability of an alloy for a bearing must 0f course be determined by practical applications where all the ramifications of service conditions are encountered, certain short cuts in the initial selection of compositions are necessary to avoid an extensive and time-consuming investigation. The present program has been to match certain metallurgical properties of the 80-10-10 bronze that have been shown by previous investigations to be related to good bearing qualities. Such properties as microstructure, hardness, compressive yield strength, ductility, and castability have been considered, and certain simple wear tests have been made. Of the readily assessed characteristics desired in a good bearing alloy, one can be certain that a uniform distribution of lead is required in a leaded bronze. It has generally been found that segregation of lead is one of the chief difficulties with this type of material. Tin has a powerful effect on lead distribution, and with 10 per cent present produces a random distribution of chunky particles, such as are shown in Fig. I. In addition, the tin bronze contains the hard alpha + delta eutectoid constituent distributed through-

Jan 1, 1945

By Richard W. Smith

There are three distinct varieties of phosphate rock, in Tennessee, known commercially as: (a) the "brown" rock, which is the residual product of the weathering and natural concentration of certain phosphatic Ordovician limestones; (b) the "blue" rock, which is an unaltered phosphatic stratum of Mississippian or Devonian age; and (c) the "white" rock, which is the result of chemical replacement and deposition. Before 1894, South Carolina and Florida had supplied most of the phosphate of the United States, South Carolina leading until that date and Florida from then until the present time. In December, 1893, the blue phosphate of Tennessee was discovered almost simultaneously on Swan Creek, in Lewis County, by two independent parties—by one as the result of a careful and systematic search for a workable deposit of the long known kidney phosphate, and by the other through mistaking it for a "bloom" of coal. Leases were taken and, with further prospecting disclosing other deposits in the region, the development progressed as rapidly as could be expected without railroad transportation. In January, 1896, Judge S. Q. Weatherly, who was interested in the development of the blue phosphate, while riding along the road south of Mt. Pleasant, noticed some slabs of a brown rock in place above the limestone. He took samples, and had them analyzed, thus discovering the high-grade brown phosphate of this district. This discovery was kept a secret until July, 1896, when mining was started at the village of Mt. Pleasant. Development proceeded rapidly, many owners obtaining their capital by the sale of their rock fences, which were largely composed of slabs of high-grade brown phosphate. The development of the brown rock, which is richer and more easily mined than the blue, caused Tennessee to advance from a poor third in production to second, surpassing the output of South Carolina, and being excelled only by Florida.

Jan 1, 1927

By D. E. Coates, G. R. Purdy, S. V. Subramanian

The morphological stability of the planar solid-liquid interface in dilute ternary alloys, undergoing steady-state unidirectional solidification, is analyzed in terms of both the constitutional supercooling principle and the perturbation methods recently developed by Mullins and Sekerka. First, various steady-state solutions for the two solute distributions ahead of a planar interface are examined. The nature of the solutions depends on the size and concentration dependence of the off-diagonal diffusion coefficients. W~thin the framework of the constitutional supercooling principle, a cumulative contribution to instability frorn the two solutes is found to exist in the absence of diffusional interaction. It is shown that the latter can produce a further enhancement of instability or can have a stabilizing influence, depending on the form of the liquidus surface and on the sign of the solute-solute interaction. A perturbation analysis, which ignores diffusional interaction, verifies the cumulative influence of lhe solute fields and demonstrates that the Mullins-Sekerka stability criterion for binary systems (with capillarity accounted for) can be readily extended for application to ternary systems. SOME time ago, Tiller et al.' calculated the solute concentration distribution ahead of the planar solid-liquid interface of binary alloys undergoing steady-state unidirectional solidification. An earlier qualitative proposal that the transition from planar to nonplanar growth morphologies is associated solely with the onset of constitutional supercooling in the liquid layer ahead of the moving interface2 was used in conjunction with this calculation to put the now well-known constitutional supercooling (C-S) stability criterion into quantitative terms. Mullins and Sekerka,3 in a recent and very elegant analysis, established a more complete criterion (hereafter referred to as the M-S criterion). Interfacial stability was investigated by determining the time derivative of the amplitude of a sinusoidal perturbation of infinitesimal amplitude which had been introduced into the originally planar shape of the moving interface. Of particular importance is the fact that capillarity was included in the boundary conditions of their calculation. The purpose of the present paper is to extend all of this earlier work on dilute binary systems for application to dilute ternary alloy solidification. The analysis is divided into three sections. In the first the two solute distributions ahead of a moving planar interface are considered. Mathematical solutions are de- termined for situations in which: a) diffusional interaction is negligible, 6) diffusional interaction must be considered but circumstances permit use of constant diffusion coefficients, and c) the concentration dependence of off-diagonal diffusion coefficients can be described by first-order dilute solution approximations. In the next section, a stability criterion analogous to the C-S criterion is developed and the influence of diffusional interaction on interface stability is analyzed. Finally, the perturbation formalism of Mullins and Sekerka, with capillarity included in the boundary conditions, is extended for analysis of ternary systems in which diffusional interaction is negligible. The study of interface stability in binary systems usually commences with the assumption that the equilibrium distribution coefficient and the slope of the liquidus line are constant at values corresponding to infinite dilution. Similar assumptions have not been introduced into the present treatment; that is, we do not assume planar solidus and liquidus surfaces joined by tie lines which yield constant distribution coefficients. The latter involves the assumption of no ther-modynamic interaction between solute species in both the solid and liquid. We consider a ternary phase diagram for which the solidus and liquidus surfaces are, in general, nonplanar and of course pass through the corresponding binary solidus and liquidus lines. These lines are not assumed to have constant slope. In the dilute regions we are concerned with, the following assumptions are made: i) The solidus and liquidus surfaces are of a form such that both the solidus and liquidus temperatures are monotonically varying functions of each solute concentration. ii) The tie lines are such that the equilibrium distribution coefficient of a given solute is greater than unity for every point on the solidus (or liquidus) surface or it is less than unity for every point. STEADY-STATE SOLUTE DISTRIBUTIONS IN THE LIQUID As will be demonstrated in the next section, a knowledge of the steady-state solute profiles is not a necessary prerequisite for the formulation of a ternary C-S stability criterion. However, in that details, such as the complete description of the equilibrium liquidus temperature profile, require an evaluation of the solute distributions, the overall treatment is enhanced if these distributions are determined. Consider a ternary system (solvent plus solutes 1 and 2) for which a planar solid-liquid interface is in unidirectional motion at constant velocity V. At this stage it is unnecessary to limit ourselves to dilute solutions. For a stationary frame of reference the generalized forms of Fick's equations are:

Jan 1, 1969

By Irwin Roman

IT has been known for many years that when a wire is moved in a magnetic field, an electromotive force is developed which is proportional to the rate at which the wire is moved in a direction perpendicular to the magnetic intensity and to the magnetic intensity itself. If the ends of the wire are connected to a current indicator, the current behaves exactly as though the source of electromotive force were a galvanic cell. If a wire is wound circularly and rotated uniformly around a diameter not parallel to the intensity, the current flowing through the wire will be alternating of sinusoidal shape. If, instead of a single loop, there are several turns wound in a short helix, the electromotive force developed will be approximately proportional to the number of turns, the area of the helix and to the speed of rotation. The maxi-mum electromotive force will be devel-oped when the axis of rotation is perpen- dicular to the field; if this is not so, only the component of the intensity that is perpendicular to the axis of rotation is effective. This is the principle of the usual earth inductor. With a few turns of wire and comparatively slow rotation, FIG. 1.-MAGNETIC GRADIOMETER. it is possible to produce a considerable deflection of a galvanometer. If two similar coils are rotated together at two different points for which the magnetic field intensities perpendicular to the axes of rotation are different, the electromotive forces developed will each depend on its corresponding intensity and be a measure of that intensity. If the inten-sities are sufficiently different so that the electromotive forces may be compared, the two intensities may be compared. This is the principle

Jan 1, 1934

By M. G. Driessen

For a number of years the cyclone, familiar to Americans as a dust collector, has been used as a thickener of suspensions at one of the coal-preparation plants of the Netherland State Mines in Limburg. The plant treats nut-size coal at 120 tons an hour in a heavy-medium washer. The diluted medium from the rinsing screens is thickened in cyclones. More recently the cyclone has been adapted to act as a coal cleaner. The principle of the cyclone thickener is the same as that of the cyclones used in industry for catching dust or fine particles suspended in the air or in gases. Generally the latter are more efficient in this respect—the smallest particles that can be caught with reasonable efficiency are considerably smaller than with the cyclone thickeners. The reason is obvious; the ratio of specific gravities between the dust particles in a gas and the gas itself is about 800 times larger than the ratio between, for instance, the specific gravities of shale particles and water. The ratio of the velocities of fall of shale particles (? = 2.5)† in air and in water is as follows: In the range of Stokes: ?air = 93?water In the range of Allen: Wair = 49Wwater In the range of Newton-Rittinger: ?air = 36.6?water The same ratios apply for the velocities in the centrifugal field, from which it follows that it is especially difficult to catch the very fine suspension particles in a liquid. The efficiency of a cyclone thickener depends mainly on the circumferential velocity of the liquid at its innermost radius, because here the centrifugal forces are the highest. However, these velocities cannot easily be calculated, as the flow is three-dimensional, and thus the axial components cannot be neglected .(p. 252, condition 3). We believe that at first a spiral tangential motion along the cyclone wall is created, which causes the inner vortex ascending from the apex of the cyclone (Fig I). At the same time the inner vortex is strengthened by the individual vortices in horizontal planes, and thus a part of the total flow can find another and perhaps quicker way to the outlet. In any case, the exact motion, not only of the fluid but especially of the suspended particles, is so difficult that we have to refer to the experiments to find the exact behavior of this kind of apparatus. Method of Judging PerforMance of Coal Washer Geologists, rather than mechanical en-gineers, would be able to describe the separating or stratifying effect in nature, but even a bather on the shore lying on the soft sand near the sea wonders why all the small sand grains have approximately the same size. A child playing on the border of the river could easily

Jan 1, 1949

By J. Chipman, N. J. Grant, H. L. Bishop, H. N. Lander

Data of several studies on the equilibrium between molten iron and open hearth-type slags have been combined to determine some of the chemical reactions involved in steel-making. Effects of slag composition and temperature on the iron oxide activity, distribution of sulfur between slag and metal, and the carbon content of the metal are discussed. Also, an overall reaction for the equilibrium between sulfur and oxygen is presented. DURING the past 15 years, a number of significant equilibrium studies have been carried out between liquid iron and simple basic and acid slags in an effort to throw light on the chemical reactions involved in steelmaking. This paper is a summary of the experimental reports on investigations which have been conducted at the Massachusetts Institute of Technology, and of related work in other laboratories. The investigations summarized in this paper include the works of Fetters and Chipman1 and Taylor and Chipman,' which dealt with simple slags that are similar to those found in the open hearth. The sulfur determinations of the slag-metal tests of Fetters and Chipman as reported by Grant and Chip-man" are included. Also, the investigations by Win-kler and Chipman' and Grant and ChipmanQ f more complex slag systems are included in this summary. The experimental procedure is described in detail in each of these papers and will not be discussed. Since the previous reports have been somewhat independent, it is desirable to review and combine the data of the various investigations to determine, as accurately as possible, the reactions in the slag-metal systems of the open hearth. It is the object of this report to present the combined data in such a way as to enhance their utility and applicability. Oxidizing Power of Slags of the System (CaO+MgO)-Si0,-FeO in Equilibrium with Carbon-Free lron The slags selected to determine the iron oxide activity in equilibrium with pure liquid iron were those containing less than 2 pct each of P,O,, MnO, or A1,0, on a weight percentage basis. The method used to calculate activities of iron oxide in liquid slags was that developed by Taylor and Chipman.' The solubility of oxygen in molten carbon-free iron under pure iron oxide slags can be expressed by the following eauation —6320 log (pctO)-------------— + 2.734 [1] where T is the absolute temperature. The oxygen solubility values as determined from Eq. 1 were used throughout this study to calculate the iron oxide activity. The iron oxide activities of slags of various iron oxide contents are plotted in Fig. 1 as a function of the basicity, which is defined as the ratio (pct CaO + pct MgO)/pct SiO,, and are based on molecular percentage values of the components. The percent (FeO), is the total iron content in the slag calculated to FeO. Fig. 1 shows that as the basicity increases at constant mol pct (FeO),, the iron oxide activity increases rapidly and reaches a plateau which extends on the basicity scale from about 1.3 to 2.3; the iron oxide activity then decreases rapidly until a basicity of about 3.0 is reached, where it tends to level off. The solid portions of the curves represent the experimental data of Fetters and Chipman and Win-kler and Chipman. Their experimental heats were made in magnesia crucibles, and hence the slags were saturated with magnesia. The broken lines on the left represent the experimental data of Taylor and Chipman, who used a rotating crucible. In general, these slags contained less than 3 pct MgO. The absence of data for slags containing less than about 40 mol pct (FeO), and basicity ratios greater than about 2.5 made it necessary to calculate curves using ionic concepts of slags. The broken lines on the right, which disregard the solubility limits of di and tricalcium silicate and lime, were obtained by following the treatment of Flood and Grjotheim,"

Jan 1, 1957

By H. R. Reed

THE cost of hoisting with electricity in deep mines is a matter about which little information has been published. This paper makes a detailed study of such costs and presents the information in a series of curves. In particular the curves show the cost of hoisting ore from depths varying from 500 to 7000 ft. vertical with the shaft at 70º incline for the double cylindroconical and double cylindrical drums, the hoists operating balanced, using Ward Leonard and Ilgner-Ward Leonard control, and designed for most economical operation from each depth. Operation with the double cylindrical drum is expanded to cover hoisting from 2000 to 5000 ft. using equipment designed for 5000 ft. and from 4000 to 7000 ft. using equipment designed for 7000 ft. Additional curves are included to show the ratings of the necessary hoist motors, energy input per hoisting cycle and size of flywheel in tons for complete equalization when the Ilgner-Ward Leonard system is used, also hoisting efficiency. The duty imposed on a mine-hoist motor fluctuates between wide limits during a cycle of operation. The demand on the motor may vary from a large horsepower value near the beginning of the cycle to a small or a negative demand near the end of the cycle. Such factors as tonnage to be raised per hour, depth of shaft, and balanced or unbalanced operation have such a marked effect on the operating cycle and vary to such an extent for different mines that no set of rules can be formulated for quickly determining the size of the motor required. The duty cycle from which the motor rating is derived must be determined for each case according to the conditions of the proposed hoisting operations. The motor torque required at the cardinal points of the duty cycle is determined from the moment or torque in pound-feet necessary to raise and lower the load and ropes, accelerate and retard the load, ropes, drum, etc. The torque diagram depends largely upon the type of drum. Two different types of drums, if used on exactly the same duty cycles, may have widely different peak demands and capacities of hoist motors. The essential feature in the design of hoisting drums and in determining

Jan 1, 1937

By Peter G. Tregelles, Derek K. Barham

Introduction A successful step towards mechanisation of the collier's work was taken in 1954 when the first Anderton shearer loader was commissioned in Lancashire, and progress was reinforced in 1956 when the first powered supports were installed in Nottinghamshire. By 1970, virtually 100% of the coalfaces in the United Kingdom were mechanised and the industry's productivity had doubled. In 1961 the National Coal Board recognised that the next move towards greater productivity and improved safety would be to automate the longwall system. What was not well enough understood, however, was that the basic prerequisites of automation - reliability and measurement - had not yet been achieved. Consequently, the schemes for automatic longwall faces and for an entirely automated colliery were abandoned at the close of the decade. A review of mining research and development policy, commissioned by the Board in 1974, confirmed that the system of longwall mining had great potential for investment and that the short-term policy of automation must once again be pursued. Since then, aided by advances in computer technology, systems for automating the transport of coal from the face to the coal preparation plant have been successfully instituted. Applications of sub-systems dealing with the conveyor, coal preparation plant, and various items of fixed plant are now at the exploitation stage. In the medium term, a number of key problems have been identified, which will arise once the productivity from the coalfaces has doubled, as it is now expected to do in the next five years. One of the most important of these problems is machine guidance, and considerable research and development work is now being carried out in this area. This paper reviews the work on machine guidance prior to 1974 and explains the programme on which the National Coal Board's Mining Research and Development Establishment is currently working.

Jan 1, 1981

By K. S. Lane

As the initial chapter in this section entitled "Role of Fluid Pressure in Rock," this attempts to fulfill an assignment for (1) summarizing the state-of-the-art and (2) illustrating engineering problems resulting from rock pore pressure. Hence, the chapter is presented in two parts: 1) Basic Concepts, and 2) Examples of Engineering Problems, including failures. Neither of these objectives has necessarily been completely met: partly from limitation of space and partly as the case histories have been restricted to the author's own field in civil engineering, and there deemphasizing those applications which will be covered in more detail by subsequent papers in this section. As with any state-of-the-art attempt, contributions of some have undoubtedly been overlooked (or omitted for brevity). Notwithstanding the foregoing limitations, it is hoped that this summary of the situation will at least: 1) Outline current concepts on effects of fluid pressure in rock-both as a pore pressure in interconnected void spaces of the intact rock and as a cleft pressure or hydraulic force acting in the joints or other discontinuities of the rock mass. 2) Indicate the often fragmentary nature of evidence presently available to support these concepts and thus encourage further research. 3) Illustrate the major significance of fluid pressure in several types of engineering problems and thus stimulate its consideration as designers encounter related situations.

Jan 1, 1970

By L. M. Pidgeon, P. G. Thornhill

A LTHOUGH a considerable number of experi--ti mental investigations dealing with the roasting of sulfide minerals have been reported in the past,'"" the behavior of the single roasting particle does not appear to have received the attention it perhaps deserves. This is understandable in that the natural sulfide counterpart of the slab or sheet of metal normally used in high temperature oxidation studies is difficult to obtain and prepare, and is, in most cases, virtually impossible to maintain in one piece at roasting temperatures. The employment, on the other hand, of static aggregations of small particles in masses great enough to permit evaluation of the roasting reactions by means of thermobalances or gas analyses introduces other complications, such as localized overheating, sintering, and variable gas-solid contact. In this investigation a compromise between the above extremes was attempted. Closely sized (e.g., 30 to 40 mesh) particles of natural sulfide minerals were isothermally roasted, out of contact with one another, in an air-swept system. The progress of the roasting reactions was followed by examination in polished section of the treated particles and by X-ray and chemical analysis of their residual sulfide kernels. In this way some conclusions respecting the mechanism of roasting reactions were drawn. Roasting Furnace—The vertical tube furnace used for roasting the sulfide particles had a heated zone 10 1/2 in. long in which four retractable light gage stainless steel trays were suspended. Each tray, and an accompanying baffle, was mounted on a 2 in. lengtn of 3/8 in. stainless steel tubing. These assemblies were axially suspended on a 30 in. length of ¼ in. stainless tubing, by means of which they could be lifted from the hot zone to a water-cooled brass chamber at the top of the furnace. Since each tray unit could slide freely on the 30 in. tube, any desired number of the trays could be retained in the cooling chamber by the manipulation of a horizontal plunger during a momentary withdrawal of the four trays from the hot zone. Although three heating coils, each equipped with variable external resistance, were employed, it was found impossible to avoid a drop of 10o to 15oC between the temperature at the top tray and that of the lower three. Consequently, only the bottom three trays were used for roasting. Temperature readings inside the furnace were made by means of a thermocouple inserted down the tray support tube at tray levels, and a separate thermocouple, inserted adjacent to the middle heating coil, was connected to a Micromax temperature control unit. Experimental Method—The sulfide minerals were obtained in a form as free as possible from gangue and contaminating sulfides, and were crushed and screened to the required particle size range. The tray assembly was kept inside the furnace during the heating-up period and, when a steady temperature had been reached, the trays were withdrawn. Each tray was sprinkled with from 200 to 500 mg of the sulfide grains, and the assembly was lowered into the furnace without delay in order to minimize the time required to achieve the operating temperature. The furnace top was then clamped into position and the thermocouple inserted down the center tube to the required level. It was found that, when this procedure was used, the trays achieved their former temperature within 2 min, after which time the flow of dry air was begun at a rate of 1 liter per min, and timing of the run was started. At the required intervals of time the trays were successively withdrawn from the hot zone and stored in the cooling chamber by means of the retention plunger. On completion of the run the treated particles were removed from the trays to be set aside for examination. The roasted particles were mounted in Lucite on a Buehler press Operating at a temperature of 140°C

Jan 1, 1958

By J. H. Wernick, D. Dorsi, K. E. Benson

A LTHOUGH a considerable number of experi--ti mental investigations dealing with the roasting of sulfide minerals have been reported in the past,'"" the behavior of the single roasting particle does not appear to have received the attention it perhaps deserves. This is understandable in that the natural sulfide counterpart of the slab or sheet of metal normally used in high temperature oxidation studies is difficult to obtain and prepare, and is, in most cases, virtually impossible to maintain in one piece at roasting temperatures. The employment, on the other hand, of static aggregations of small particles in masses great enough to permit evaluation of the roasting reactions by means of thermobalances or gas analyses introduces other complications, such as localized overheating, sintering, and variable gas-solid contact. In this investigation a compromise between the above extremes was attempted. Closely sized (e.g., 30 to 40 mesh) particles of natural sulfide minerals were isothermally roasted, out of contact with one another, in an air-swept system. The progress of the roasting reactions was followed by examination in polished section of the treated particles and by X-ray and chemical analysis of their residual sulfide kernels. In this way some conclusions respecting the mechanism of roasting reactions were drawn. Roasting Furnace—The vertical tube furnace used for roasting the sulfide particles had a heated zone 10 1/2 in. long in which four retractable light gage stainless steel trays were suspended. Each tray, and an accompanying baffle, was mounted on a 2 in. iength of 3/8 in. stainless steel tubing. These assemblies were axially suspended on a 30 in. length of in. stainless tubing, by means of which they could be lifted from the hot zone to a water-cooled brass chamber at the top of the furnace. Since each tray unit could slide freely on the 30 in. tube, any desired number of the trays could be retained in the cooling chamber by the manipulation of a horizontal plunger during a momentary withdrawal of the four trays from the hot zone. Although three heating coils, each equipped with variable external resistance, were employed, it was found impossible to avoid a drop of 10O to 15OC between the temperature at the top tray and that of the lower three. Consequently, only the bottom three trays were used for roasting. Temperature readings inside the furnace were made by means of a thermocouple inserted down the tray support tube at tray levels, and a separate thermocouple, inserted adjacent to the middle heating coil, was connected to a Micromax temperature control unit. Experimental Method—The sulfide minerals were obtained in a form as free as possible from gangue and contaminating sulfides, and were crushed and screened to the required particle size range. The tray assembly was kept inside the furnace during the heating-up period and, when a steady temperature had been reached, the trays were withdrawn. Each tray was sprinkled with from 200 to 500 mg of the sulfide grains, and the assembly was lowered into the furnace without delay in order to minimize the time required to achieve the operating temperature. The furnace top was then clamped into position and the thermocouple inserted down the center tube to the required level. It was found that, when this procedure was used, the trays achieved their former temperature within 2 min, after which time the flow of dry air was begun at a rate of 1 liter per min, and timing of the run was started. At the required intervals of time the trays were successively withdrawn from the hot zone and stored in the cooling chamber by means of the retention plunger. On completion of the run the treated particles were removed from the trays to be set aside for examination. The roasted particles were mounted in Lucite on a Buehler press operating at a temperature of 146°C

Jan 1, 1958

By N. A. Gokcen, R. A. Dodd

Solubility of nitrogen in liquid iron-manganese system at 1550°C and one atmosphere pressure has been determined by a simple method. Results show that the solubility increases from 0.040 pct for pure iron to 1.41 pct for pure manganese. DETERMINATION of the solubility of gases in volatile metals. and alloys by the well-known Sievertsl method is unreliable. This is particularly true for the Fe-Mn system since Mn vaporizes readily from the alloys containing as little as 2 pct Mn, and, upon condensing on the cooler parts of the apparatus, it absorbs large amounts of nitrogen. Further, the condensing Mn vapor interferes with the usual method of temperature measurements with an optical pyrometer.

Jan 1, 1962

By E. L. Bruce

GOLD occurs ill many mineral deposits in the rocks of the Canadian Shield. It is present in the ores of many base metals and a considerable quantity is recovered as a by-product from the production of copper at Noranda, of nickel and copper at Sudbury and of copper and zinc at Flinflon. But the greater part of the gold production of Canada is from deposits in which gold is the only metal of value. No gold is obtained from placer deposits within the borders of the Canadian Shield. A brief review of the geological relations of some of the gold deposits of the Canadian Shield will be presented in an attempt to explain certain associations. Only those which are being worked for their gold content will be considered and descriptions will be confined to representative types of deposits, chiefly those of major importance; a few others, differing in certain features from those of the older and larger mines, will be included in order to illustrate the general conditions in which gold occurs in these ancient rocks. Brief summaries will be given of the geological relations of the Beattie and Siscoe mines of northern Quebec, of the mines of the Porcupine and Kirkland Lake areas of northeastern Ontario and of the Howey, Central Patricia and Little Long Lac mines of northwestern Ontario. Genetic relations to igneous rocks of granitic composition, outcropping in the vicinity, have been assumed for many of these deposits. Undoubtedly the ore minerals have been derived from igneous sources and, for some occurrences, there is evidence suggestive of genetic relationship between the ore bodies and neighbouring intrusive rocks. During the past few years, however, many investigators have expressed doubt of the genetic relationship of certain ore bodies to igneous masses near which they occur. As will be seen from references in the following descriptions the importance of the structural conditions in localizing deposition has been realized. This is pointed out for Canadian pre-Cambrian gold deposits by E. T. Dougherty, who also refers to the

Jan 1, 1937

By S. S. Shen, M. J. Pool, P. J. Spencer

Heats of solution of silver and copper in dilute Ag-Cu-Sn alloys at 720°K have been determined using a liquid metal-solution calorieter. Values of the se2f-interaction coefficient n AgAghave been calculated at constant copper concentrations and n Cu Cuhas been determined at constant silver contents. The reliability of the experimental data is shown by the very good agreement between nCujAg and ij &$; these interaction coefficients have experimental values of -9100 and - 9590 cal per g-atom, respectively. Certain solution models are shown to be inadequate for prediction of solute interaction coefficients in dilute Ag-Cu-Sn alloys. In a previous publication' the results of a thermody-namic study of dilute Ag-Au-Sn alloys were presented. The present work represents the continuation of a program to investigate dilute alloys of the noble metals with tin and in particular is concerned with solute interactions in the Ag-Cu-Sn system. By determination of the magnitude and sign of the various interaction coefficients in dilute alloys it is possible to gain some understanding of the different types of solute-solute and so lute-solvent bonding changes that occur as the solute concentrations are varied. Hence systematic studies of alloys with similar physical characteristics as regards size, structure, electronegativity, and so forth, of their components can contribute a great deal to present theoretical knowledge of solutions. The recent definition of an enthalpy interaction coefficient, 11, by Lupis and Elliott2 is of particular value in calorimetric studies such as the present one: where j and i are solutes and s is the solvent; Si is the relative partial molar enthalpy of component i and x represents the mole fraction of solute or solvent. Values of ?Hi can be obtained directly by solution calorimetry and data for n are thus easily determined, often with a high degree of accuracy. ?Hi is related to the relative partial molar enthalpy at infinite dilution, ?Hi and to the enthalpy interaction coefficients by the expression: ?Hi?Hi + X;nz+ ... [2] The aim of the present work was to determine the self-interaction coefficients n AgAgand 178: in alloys of different compositions and also to establish values for n Agcg| and ncuAg. Since it is a thermodynamic requirement (resulting from the Maxwell-type relationships which can be applied to partial molar properties) that nAgcu and ncuAg should be equal, a further aim of this study was to demonstrate the agreement between experiment and theory. EXPERIMENTAL A description of the liquid metal-solution calorimeter used in this research has already been published,3 and no further details of its construction and operation will therefore be given here. Copper supplied by the American Smelting and Refining Co. was indicated by them as being 99.999 pct pure, and the silver obtained from A. D. Mackay, Inc., was also quoted as being 99.999 pct pure. A solvent bath consisting of between 70 and 80 g of 99.99 pct pure Sn was used for each series of experimental drops. Its weight was accurately determined and the appropriate amounts of copper or silver were added to give alloys of the desired composition. Approximately 0.00125 g-atom additions were used for determinations of the heat of solution of silver in the bath, while, for copper, specimens consisting of approximately 0.0015 g-atom were used. The heat capacity of the bath was determined at regular intervals during a series of drops using tin or tungsten calibration samples. The heats of solution of silver and copper in pure tin were first determined as a function of their concentration in order to establish the self-interaction coefficients 7AgAg and ncucu Alloys containing a constant 0.01, 0.02, 0.03, and 0.04 mole fraction of copper were then used to study 17:: in alloys of different copper content, while alloys of the same mole fractions of silver were used to determine equivalent data for 178: at constant silver concentrations. The composition of the bath was held at the desired copper or silver concentration by making calculated additions of the appropriate solute throughout the experiment. From the limiting values of ?HAg in the constant copper content alloys it was possible to study ?HAg as a function of xCu and hence to determine 42:. A similar analysis of the re, values permitted calculation of nAgcu. Heat content and heat capacity data from Hultgren et al* were used to calculate heat of solution values from the measured heat effects at the experimental temperature of 720°K. RESULTS AND DISCUSSION Determinations of ?HAg. A preliminary investigation of the heat of solution of silver in pure tin at 720°K was first made in order to establish the value of nAgAg before additions of copper were made and also to compare the value of ?HOAg(l) with that obtained in the previous study of Ag-Au-Sn alloys.' Then the heat of solution of silver in Cu-Sn alloys was investigated as a func-

Jan 1, 1970

By H. W. Young

DEVELOPMENT of high-tension outdoor substations during the past few years has been due primarily to economic reasons. The demand for power in small communities could not be met with the conventional and 1 FIG. 1.-33,000-VOLT STEP-UP OUTDOOR AIR-BREAK SWITCH AND SUBSTATION INSTALLATION OUTSIDE OF A POWERHOUSE GENERATING AT 2300 VOLTS STEPPING UP TO 33,000. TWENTY-ONE COAL MINES ARE SUPPLIED FROM LINES LEADING FROM THIS INSTALLATION. comparatively expensive indoor types unless the rate for service was materially increased. That the various problems incident to development have been solved successfully, it is only necessary to point to the

Jan 9, 1919

By L. S. Castleman, L. L. Seigle

THE formation and growth of intermetallic phase layers is of considerable practical importance to metallurgists interested in diffusion bonding and cementation processes and has been the subject of extensive qualitative investigation. In contrast, it is somewhat surprising that so little quantitative data have been amassed. The need for additional fundamental work was pointed out by Mehl in 1936,' and persists to a large extent to the present day. The early studies have been reviewed by Rhines,2 and his conclusions have been summarized by Lustman and Mehl3 substantially as follows: 1) All phases that are stable at the temperature at which diffusion occurs will appear in the interdiffusion of two metals; however, in some cases, certain of the phases may be too thin to be observed and identified easily. 2) The isothermal growth of intermetallic phases generally obeys a simple parabolic equation of the form X2 = Kt, where x is the thickness of the alloy layer, K the temperature dependent reaction rate constant, and t the time. 3) The rate of thickening varies with temperature according to the Arrhenius equation k = Ae -Q/RT , where k is the parabolic rate constant, A, a temperature independent constant, Q the heat of activation for the process, R the gas constant, and T the absolute temperature. Subsequently, Lustman and Mehl made a quantitative study of the laws of growth in intermediate layers in a number of binary systems, in which one of the components was either zinc or cadmium, and the other component was one of the following: nickel, copper, silver, cobalt, gold, iron, or Monel metal; the interdiffusion times used were for the most part less than 24 hr. It was found that the simple parabolic law was not obeyed in general, but that a generalized parabolic law of the form xn = kt was valid, where n was a temperature dependent constant; also,

Jan 1, 1959

By W. L. Martin, J. N. Dew, H. B. Steves, M. L. Powers

This paper presents and discusses the results obtained during a pilot test in the Loco field in southern Okla homa. The test was conducted in a 2%-acre pattern that was part of a 20-acre conventional waterflood pilot area. The conventional flood was well past its economic limit when the hot waterflood was initiated to obtain technical information and operating experience. Temperature data from nine observation wells showed that about 75 percent of the pattern was affected by heat, and that heat losses were severe in the pilot pattern. About 60 percent of the injected heat was lost to overburden and underburden zones during hot-water injection. Wellbore heat losses were held at tolerable levels at the shallow depth of the test by providing a low-pressure air annulus between the injection tubing and well casing. Hot water provided water injectivity increases of 200 to 400 percent. The hot water channeled across the lower portion of the oil sand in three directions through zones of relatively high water saturation. There was no conclusive evidence that natural fractures or pressure partings aflected the flow of fluids in the pilot pattern; however response undoubtedly was aflected by localized pressure gradients and by injection-production rate ratios. The results showed that hot waterflooding increased oil recovery in a reservoir containing 600 cp oil. The total tertiary oil production from the pilot pattern area was 3,896 bbl or about 156 bbl/acre-ft swept by heat. The corre.sponding WOR was about 34:I. Description of the Hot Waterflood Process To hot waterflood an oil reservoir, water is injected that has been heated to a temperature substantially higher than the original reservoir temperature, but lower than the vaporization temperature of water at the prevailing pressures. In the reservoir the hot water flows continuously into cooler sand and rapidly loses heat to the sand until it has been cooled to the original reservoir temperature. Thus, a heated zone and a region or "bank" of cooled water begins to accumulate immediately after hot water injection is started. This bank of cooled water continues to grow ahead of the heated zone, which also grows, but at a slower rate. This occurs because heat transfer is almost instantaneous, and the ratio of heat capacities of water to rock is such that two or three unit PV of hot water must be injected to heat a given unit bulk volume of the reservoir. The primary displacement mechanism is the same for both hot and conventional cold waterfloods; i.e., "piston" displacement occurs at the original reservoir temperature. The incremental benefits of hot waterflooding usually occur long after the breakthrough of cold water at producing wells, and the increased oil recovery necessarily is accomplished with high WOR's (water-oil ratios). Heat decreases the viscosity and density of oil and water. These effects result in more rapid and increased recovery of secondary or tertiary oil. If the cost of the required heat is low enough, the ultimate oil recovery of a hot waterflood should be increased substantially over what would be expected at the economic limit of a conventional cold waterflood. The economic benefits of any hot-fluid injection project depend primarily upon the cost of the heat required to produce more oil at an increased rate. This cost depends in part upon the amount of heat lost to surrounding formations. Heat loss depends upon reservoir thickness, water injection rate and temperature, the depth of the formation, well spacing, and the characteristics of the reservoir rock and surrounding formations. In general, percentage heat losses decrease as injection rate and reservoir thickness increase. Although it is an old idea, hot-water injection has not received widespread field application in the oil industry as a drive process. Much of the original field work with hot water was done in Pennsylvania fields where water permeabilities and injection rates are low. In these cases, hot-water injection was used primarily as a means of increasing in-jectivities — not as a recovery process. Ramey' recently has published an excellent review of the development of hot fluid injection processes. Recent publications"' and our own experiences now indicate that hot water or steam injection also can effectively increase the oil recovery from reservoirs containing viscous crudes. However, the economics of these methods as displacement processes have not been established. Several theoretical predictive techniques have been published (for a review see Ramey'), but simplifying assumptions make

Jan 1, 1969