Search Documents

By John W. Brauns, David H. Orr

9.1-1. Description and Basic Function. A conventional railroad haulage system for a surface mine performs the function of transporting the ore and/or waste out of the pit to a crushing plant or dump. Trains consisting of a locomotive and gondola or side-dump care suitable for loading by power shovels are used. Gondola cars are restricted to hauling ore as a rotary dumper is required to unload them. Side-dump cars are more versa- tile, being satisfactory for carrying both ore and waste; but because of their additional dumping mechanism they are likely to be more expensive to maintain (12). Also they weigh up to two times as much as a flat-bottom car of the same capacity, and, therefore, fewer cars can be hauled per train. Standard-gauge track is most commonly used. Track systems incorporate temporary track of low quality in areas where moves are frequent and permanent track of high quality on main lines. Rail haulage enabled open pit mining to establish its reputation, for efficiency. Prior to World War II it was the principal type of transportation used in large pits. Other successful surface mine haulage methods have been developed since that time. These have served to supplement railroad transportation, permitting selection of a method that is best adapted to the peculiar requirements of each mining project. 9.1-2. General Applicability and Controlling Physical Conditions. For handling rough rock, the shovel-train system is unexcelled (6). The ideal application is in a physically large, but not excessively deep, open pit mine from which the coarsely blasted ore and waste must be transported distances in excess of three miles. If, in addition, a high production rate is to be maintained, railroad haulage will probably afford a lower cost per ton transported than will any other haulage method. Relatively gentle

Jan 1, 1968

By J. N. Hummel

THE methods of electrical prospecting, which employ contact electrodes to produce an electric field in the ground, furnish information concerning the constitution of the material beneath the surface, as indicated by the distortion of this artificially produced field and anomalies therein. To reveal the distortion of such field of known character, it is only necessary to measure qualitatively the direction of the field, using sensitive compensation methods. In such a case, the survey is relatively simple, and that is an important factor from a practical point of view, The distortion of the normal field thus determined permits an easy interpretation and gives approximate information as to the subsurface conditions, without the necessity of a thorough theoretical knowledge of the electrical field. The true field of application of the equipotential lines and search-coil methods, which are based on this principle of directional determination of the electrical field in the ground, is that of search for deposits of economic minerals for the mining industry, although they can also be used in solution of other problems; for example, in the determination of the strike of anisotropic beds. The distortion of the electric field as represented by the picture of equipotential lines or other measured curves is striking only when bodies having conductivities different from that of the country rock are embedded in the underground, or when the underground is anisotropic.

Jan 1, 1931

By D. S. Gleason, D. E. Severson, D. R. Skidmore

Pittsburg and Midway Coal Co. has modified the German Pott-Broche process, on which patents date back to 1927, to produce on a bench scale liquid products by solution hydrogenation of coal. A continuing program of lignite solution-hydro gena-tion experiments is directed toward investigating coal solution reactions, determining favorable conditions for the solution refining of lignite by the Pott-Broche process, and investigating some of the uses for the de-ashed product obtained from lignite The German Pott-Broche process1" on which patents date back to 1927, has been modified by the Pittsburg and Midway Coal Co., a Gulf Oil subsidiary, to produce on a bench scale liquid products by solution -hydrogena-tion of coal." The objectives of the present effort are to investigate coal solution reactions, to determine favorable conditions for the solution refining of lignite by the Pott-Broche process, and to investigate some of the uses for the de-ashed product obtained from lignite. This paper is a summary of results to date in a continuing program of lignite solution-hydrogenation experiments. The coal solution reaction program has several principal aims. The first of these is to determine whether lignite can be successfully dissolved in solvents that might be practical for commercial development. The second object is to determine whether the solvents function after successive cycles of use, recovery, and reuse. It seems necessary to the economics of a potential commercial process that the solvent be recycled. Third, it is desired to learn something about the distribution of the ash constituents between cake and filtrate. The extent of ash removal is important. The nature and quantity of mineral matter passing through the filter may determine end-use marketability. For certain use applications, trace quantities of certain minerals can be objectionable, e.g., titanium and vanadium must be very low in electrode carbon for aluminum production. The Solution Reaction The coal solution Process involves an extremely complex system of chemical reactions. An initial solvent such as anthracene oil is a mixture of hundreds of different compounds with a boiling range of roughly 500" to 750°F at atmospheric pressure. The coal macro-molecule is broken down by thermal decomposition and solvent action into myriads of different compounds, some the same as those comprising the solvent. This similarity in structures opens up the possibility of production and subsequent recovery of solvent. Some solvent is inevitably lost by reaction. Regeneration of solvent was not a problem in the early German Pott-Broche plant. The coal refinery was an integral part of a petroleum refinery complex and replacement solvent was readily available. A coal refinery using lignite, however, might be isolated from other hydrocarbon processing facilities and the regenerability of solvent could be vital to the economic success of the venture. Several structural features of the solvent molecules have been cited as important to the coal solution process.'. The first of these is aromaticity of the material, the second, ability to transfer hydrogen to another molecule, as for example the ability of tetralin to transfer hydrogen and be converted to naphthalene. Finally, the presence of hydroxyl groups on aromatic rings within the molecule, i.e., phenolic character, seems beneficial. Mixtures of pure compounds have been tried by various investigators. Mixtures of o-cresol, a phenolic substance, and tetralin were found to dissolve bituminous coal better than either substance alone.3 This maximum solubility was not found with lignite." Hydrogen contributes to the reaction by hydro-genolysis and by combining with free radicals and molecular "loose ends" to stabilize the compounds formed in coal depolymerization. High boiling point, and correspondingly high molecular weight, seems to be a property which improves solution potential for coal with a given type of compound.' The maceral components of the coal appear to have an important bearing on its ease of solution. The fusain portion is quite inert to solvent action, but the an-thraxylon material dissolves quite readily.3 The hydrogenation reaction can be improved by the use of a catalyst; commercial hydrogenation catalysts having been found effective. Although cost is involved in the use of catalyst and catalyst recovery, the resulting saving in time and perhaps lowered temperature or pressure might justify their use in the solution refining process and decrease the total process costs. Apparatus and Procedure The coal solution runs were made in a 1-gal stainless steel stirred autoclave. The autoclave was provided with thermocouple wells and a transducer to permit continuous recording of temperature and pressure. The autoclave stirrer was magnetically driven, eliminating the leakage inherent with a rotating pressure seal. For runs in which a catalyst was used, the catalyst in the form of beads was placed in a wire mesh container mounted on the stirrer shaft. A control system programmed the heatup and reaction cycle. The permissible heating rate was 5°F per min because of the need to minimize thermal stress in the autoclave body. The temperature was raised at that rate until the reaction temperature was attained and then the temperature was held constant for the desired length of time. The maximum temperature seldom exceeded the average run temperature by more than 15°F.

Jan 1, 1971

By M. L. Pearce

A comparison of the isotope-dilution, vacuum-fusion, and chemical methods of analysis for nitrogen in Si-Fe is made with particular emphasis on the effect of sample history. The superiority of the isotope-dilution method from the point of view of 1 HE analytical techniques used to determine nitrogen in Si-Fe have been subjected to close scrutiny in recent years primarily because of the marked influence of the element on the properties of the alloy. These investigations have led to a diversity of opin- both precision and accuracy is demonstrated. The solubility of nitrogen in 3.06 pct Si-Fe is investigated and the effect of silicon content on the activity coefficient of nitrogen is derived. ion regarding the reliability of the vacuum-fusion and chemical methods of nitrogen analysis when applied to si- Fe.'-' A majority of workers appear to favor the vacuum-fusion method over chemical methods particularly in those cases where part of the nitrogen may exist as silicon nitride or the total nitrogen content is very low. Contrary views have been expressed, however,' and it has been demonstrated that for some Si-Fe alloys both methods yield results which are significantly lower than those

Jan 1, 1963

By O. Hoover, M. Herman, V. V. Damiano

The Jetter and borie' teclznique of determining textures using a spherical specimen has been applied to tlze study of compression-rolled beryllium sheet. Snzall spheres the order of 1 mm in diam cut from the beryllium sheet were autotnatically rotated about tz41o axes using the G.E. single-crystal goniometer. Quantitative pole figures were obtained without tke need to apply absorption corrections. Compression-rolled beryllium exhibited peak intensities ,for (0002) planes of positions tilted 10 deg to the rolling plane and a near random distribution of (1010) planes about the nornal to the rolling plane. TECHNIQUES for determining textures of rolled sheet material are amply described in the literature. The techniques are found to be variations of two basic methods. One due to Decker, Asp, and arker, referred to as the transmission method, utilizes a thin-sheet specimen in which the X-ray beam enters the specimen from one side and the intensity of the beam which emerges from the opposite side is measured. The second method due to chulz,3 referred to as the reflection method, utilizes a thick specimen and the intensity of the beam emerging from the same side is measured. The two rotations of the specimen in the beam are designated a and 8. In order to completely determine the texture of sheet material, it is generally necessary to use a combination of the two methods. The calculations involved in correcting the raw X-ray data for absorption effects and the combining of the data obtained by the two methods are very laborious and time consuming. To avoid the intensity corrections which arise as a result of the changing diffraction volume and path length within the sample other methods have been proposed. The Norton method utilizes a cylindrically shaped specimen cut from the sheet material. Since the rods have rotational symmetry, the absorption correction is constant for rotations about the sheet texture. Jetter and Borie' employed a spherical specimen to analyze the fiber texture of extruded aluminum rods. The spheres were rotated rapidly about the fiber axis to include a large number of grains in the X-ray beam and changes in intensity with respect to tilts of the fiber axis were measured. The absorption correction was constant for all angles and was neglected. The Jetter and Borie' technique finds excellent ap- plication to very fine-grained low-absorbing metals in which the entire sphere volume can contribute to the diffraction volume. In the case of low-absorbing metals, however, serious limitations on specimen thickness occur as demonstrated by Braggs due to de-focussing effects. Peak shifts may occur which negate the assumption that integrated intensities are proportional to peak intensities. These limitations in sphere size to the order of 0.5 to 1 mm for beryllium require that the grain size be sufficiently small to include a large enough statistical sample. The present paper describes the application of spherical specimens less than 1 mm in diam to the quantitative determination of pole figures for compression-rolled beryllium sheet having a grain size the order of 10 p. EXPERIMENTAL 1) Specimen Preparation. Two techniques for spark-machining beryllium spheres were tried. One involved the use of a hollow cylinder as a cutting tool. The tool was fed into the rotating cylindrical specimen as shown in Fig. l(a). The hollow cylinder was carefully aligned such that the axis of the cylinder and the axis of the specimen lay in the same plane and were 90 deg to each other. As the hollow cylinder was fed into the rotating cylindrical specimen, a spherical shape was formed as shown in Fig. 1. Alignment was very critical. Slight misalignment resulted in the formation of a barrel-shaped specimen instead of a sphere. A second technique involved the use of a cutting wheel shaped as shown in Fig. 2 with a groove of the desired radius. A section of the sheet specimen was first turned into a cylinder on the left part of the cutting wheel. It was then shifted to the right and a spherical specimen was turned as shown in Fig. 2. The axis of the cylinder lay in the plane of the sheet. Flats corresponding to the rolling plane of the sheet were used to grip the specimen during the machining operation and these served to identify the rolling plane of the sphere. 2) Rotation of Spec=. The spherical specimen is shown mounted on the G.E. single-crystal goniometer in Fig. 3. The knob A of the goniometer shown in Fig. 3 rotates the specimen about the pedestal axis. These angles have been designated as @ angles. The knob B rotates the specimen about an axis perpendicular to the pedestal axis. These angles have been designated as p angles. A device was made to automatically drive the single-crystal goniometer by means of two flexible shafts connected to the A and B knobs as shown in Fig. 3. The motor system was designed to rotate the knob A, thus rotating the specimen through angles of $I while the B knob remained stationary. After one complete

Jan 1, 1967

By Norman Hedley, George Barsky, S. J. Sawinson

The cyanidation of precious-metal ores is a complex chemical process. Numerous reactions occur, some of which cause an undesired consumption of alkali and of cyanide. A knowledge of these reactions, their products, and the factors that influence the rates at which they proceed should be of value in working out the most economical conditions for cyanidation; but at present, much of this knowledge is lacking. This paper is confined to a study of some of the fundamentals of cyanidation. At the start of such an investigation it is necessary to simplify the problem under consideration by eliminating as many variables as possible. The results are then, of course, not immediately applicable to practice, but it is hoped in further work to round out the information and thereby make it of more practical value. For convenience in presentation, the paper has been divided into two parts, one devoted to a study of the reaction between cyanide and gold or silver, the other to a consideration of the factors that determine the rate of dissolution. I. REACTIONS INVOLVED IN DISSOLUTION OF GOLD AND SILVER IN DILUTE CYANIDE SOLUTIONS Ever since the cyanide process for gold and silver extraction was introduced there has been discussion of the equation representing the reactions involved. In undertaking a detailed study of these factors, it was felt that the most logical first step was to determine, if possible, what reactions could theoretically take place when gold and sill-er are dissolved by dilute cyanide solutions. It is possible to determine whether or not a given reaction will theoretically take place by calculating the free energy of the reaction. This free-energy value for any given reaction is the algebraic sum of the free energies of formation of each of the reactants and products, and, if these values are known, the calculation is simple. (A chemical change always involves an energy change and the amount of energy change involved is the factor determining whether a given reaction will take place or how far it will go. In chemistry we consider what is known as the "free energy"; that is, the maximum amount of energy that can be utilized as

Jan 1, 1935

By H. L. Hopkins, L. W. Kempf

Aluminum alloys, in common with most other metallic alloys exhibit slight density changes with variations in temper achieved by heat-treatment, which usually are the result of the variation with temperature of the solid solubility of the various alloy constituents in the solvent metal. Changes in density are, of course, most marked in conditions that exhibit the maximum variation in solid solubility of the constituents. In aluminum alloys these conditions usually prevail when alloys are quenched from just below the melting point and are subsequently reheated to some lower temperature. Since commercial heat-treatments may be of this type, the density changes, although small (of the order of 0.3 per cent which may be compared with the density change of about 1.5 per cent involved in the transformation, at ordinary temperatures, of gamma to alpha iron during the hardening of steel), may in some specific applications necessitate quantitative consideration. This phenomenon has been investigated extensively in the laboratories of the Aluminum Company of America over a period of years. A number of investigators '-5t have observed and measured the density changes accompanying the heat-treatment of aluminum alloys. In general, these changes have not been directly translated to dimensional changes and their significance has been overlooked to some extent by the practical user of aluminum alloys. It is the purpose of this paper to consider some practical aspects of these density and dimensional changes. These density changes were given some consideration in 1917 in connection with the use of aluminum-alloy pistons for aircraft engines. Investigations by Lea and Shakespear were reported in some confidential reports of the British Advisory Committee for Aeronautics, Light Alloys Subcommittee, during 1917 and 1918, which are not generally available in published form. In these reports the term "permanent growth" was applied to the dimensional changes occurring in the pistons at the tem-

Jan 1, 1936

By P. D. P. Hamilton

In any mining district where benefication of the ores is practiced, one can usually observe several types of flow sheets even though the various producers are milling ore from the same geological formations. It is obviously impossible to describe all the mills in the Porcupine district. However, the following description of some of them is of particular interest in that it shows where one mill has paid particular attention to corduroy blanket practice; one to gravity concentration of sulfides for intensive cyanidation of the values therein contained; one to flotation of values and cyanidation of this product only; and others where small variations of standard all-slime cyanidation practice prevail. In all cases it will be seen that cyanidation is the basic principle. Discussions involving the difference in the flow sheets and the reasons for them will always be of value to those interested in the art. The author of this article, however, believes that such discussions should originate from the operators of the mills under discussion. For this reason no comparisons or discussion will be included in the description of the mills mentioned. Should any reader of this article obtain information therefrom which will be of value to him in helping to solve his own particular problems, the author will consider that the article has satisfactorily served its purpose. All values mentioned throughout this article are based on the value of gold at $20.67 per ounce. Coniaurum Mines, Limited The ore of the Coniaurium mines consists of a mineralized schist and quartz containing about 2.5 per cent sulfides. Owing to the low grade of ore developed in the mine, extreme care has had to be exercised throughout the entire mining and milling operation in order that an operating profit might be obtained. The management, however, has been able to keep costs down, with the result that at present the outlook for the property is considerably brighter than it has been in the past. This is partly due to the fact that it is now known how to mine and treat

Jan 1, 1935

By B. C. Burgess

IN the first edition of this volume,44 feldspar was introduced as "the I commonest mineral of the crystalline rocks," usually in small grains associated with other minerals and commercially produced only from pegrnatites. Now other crystalline rocks, such as alaskites and granites, have become present or potential sources of feldspar. In addition, feldspar has encountered very vigorous competition from such substitutes as nepheline syenite and aplite. COMPOSITION AND PROPERTIES The feldspars form a group of which the principal species are orthoclase, microcline, albite, and anorthite. These are aluminum silicates of potassium, sodium and calcium. There are also a barium feldspar, celsian, and barium orthoclase feldspar, hyalophane, rarely found and of no commercial importance. None of the minerals in the feldspar group are found pure or nearly pure. The potash feldspars, orthoclase and microcline, nearly always contain some albite (soda microcline, an- orthoclase); the soda feldspars usually contain some anorthite (lime feldspar). There is a series of soda-lime feldspars known as plagioclase in which the albite and anorthite molecules replace each other in varying proportions from albite through oligoclase, andesine, labradorite, and bytownite to anorthite. Theoretical chemical composition of the principal feldspars is given in Table 1. The Whiteware Division of the American Ceramic Society sub- mitted a list of definitions of ceramic terms, in April 1947, for use in technical literature. For feldspar it gives: "A group of igneous minerals consisting chiefly of the aluminum silicates of potash, soda and lime, in which one base generally predominates." Commercial feldspars are intergrowths of at least two species of feldspar, which occur associated with one or more accessory minerals such as quartz, muscovite, biotite, garnet and tourmaline as well as with small but varying proportions of the decomposition product, kaolinite. An intergrowth of quartz and feldspar frequently contains

Jan 1, 1949

By Morris Muskat

A theory is presented for calculating the performance history of complete water-drive systems producing from idealized stratified formations. The general equations are applied to systems where the permeability stratification is either of the exponential or linear type. Calculations were carried through for different degrees of permeability stratification, but with special emphasis on the effect of the mobility ratio between the produced oil and the invading water on the resultant performance. These results are also expressed graphically as curves for the initial water breakthrough recovery, for the different degrees of stratification, as a function of the mobility ratio, and of the composition of the produced fluid stream as a function of the cumulative oil recovery. For several typical cases the latter has also been plotted as a function of the cumulative oil and water throughflow. The general result is that when the mobility of the oil is lower than that of the invading water the channelling tendency resulting from the permeability stratification becomes aggravated as the higher permeability zones become flooded out. Situations of this type would obtain when producing low gravity or highly viscous oils. Conversely, if the mobility of the oil is high compared to that of the invading water, the flooding of the high permeability zones will lead to a retarding and choking effect, and the gross bypassing phenomena will be partially suppressed. These conditions would correspond to those of flooding high gravity or low viscosity oils. A discussion is given of the various basic assumptions made in the analysis, including that of ignoring the stripping phase of the production history as implied by relative permeability concepts. INTRODUCTION The physical ultimate recoveries from oil reservoirs are basically determined and limited by the physical oil displacement processes associated with the reservoir producing mechanism. In practice, however, the economic ultimate recoveries are further limited by the mobility of the reservoir fluids and the uniformity and continuity of the producing formation. In fact, it is the differential depletion between the component parts of the composite reservoir which ultimately determines the total recovery at the time of field abandonment. While this observation applies to both the solution gas drive and gravity drainage mechanisms, in which use is made only of the energy contained within the original oil-bearing reservoir, it is of even more paramount importance under operations wherein the energy associated with extraneous fluids provides the ultimate oil expulsion mechanism. Whether the invading fluid is the water from an edgewater drive, water injected for pressure maintenance, gas injected for pressure maintenance, or gas returned to the formation in a cycling program, it is often the continuity and uniformity of the producing section which will control the economic efficiency of the operations. The importance of the problem of reservoir non-uniformity does not, of course, lessen its complexity or the difficulties of its solution. In fact, these are inherently such that the concept of a "general" solution is virtually meaningless. About all that can be reasonably hoped for is the analysis of specific and well-defined types of non-uniformity which may give some degree of approximation to actual reservoir conditions. Since variations in the nature of the reservoir which depend only on the position along the streamlines will not lead directly to major differential depletion development within the reservoir, the types of non-uniformity considered thus far have involved stratification assumptions. That is, the producing section has been replaced by a multi-layer "sandwich," each uniform areally, and differing from the others only in its basic physical constants as to thickness, porosity and permeability. The fluid motion in the composite system is thus approximated by a parallel superposition of the independent fluid movements in the individual strata. For the specific application to cycling operations the theory of the effect of permeability stratification has been developed for both discontinuous' and continuous types of permeability stratification. Among the latter, treatments have been given of systems in which permeability distributions are governed by exponential, linear' or probability3 functions. In all these studies complete dynamical equivalence was assumed between the injected dry gas and the displaced wet gas. The overall effective permeability of each stratum was therefore considered as constant and independent of the degree of invasion of the injected fluid. In the case of the displacement of oil by water, the assumption of dynamical equivalence between the water and oil will be strictly valid only by accident. Even if the oil viscosity should be the same as that of the water, the effective permeability to the oil in the presence of the connate water will in general be quite different from that of the water behind the water-oil interface flowing past the trapped residual oil. As a result the effective permeability for the stratum as a whole and rate of water invasion will change with time as the intrusion continues. The differential fluid motion in the individual strata will thus also vary with time. Qualitatively, it is easy to predict the resultant effects. If the permeability to viscosity ratio of the invading fluid exceeds that of the fluid displaced, the stratification and bypassing effect of the perme-

Jan 1, 1950

By Hans Rumpf

INTRODUCTION Agglomeration is based on adhesion between particles. Production of agglomerates of specific strength, strain properties, size, porosity and structure necessitates the activation of the adhesive forces. To achieve this, it is important for us to know details of the various systems of adhesion. Reports on the work of our Institute for the investigation of systems of adhesion were published on various occasions. A reference to those publications is made in the following abstract, and the findings previously published are presented only to the extent necessary for a better understanding of more recent test results, or of changed ideas. 1. MECHANISMS OF ADHESION We must distinguish between various "mechanisms of adhesion". By "mechanism of adhesion" we understand the interaction between a particle and a substrate resulting from a clearly definable physical or physico-chemical process resulting in a definite mathematical interrelation- ship between the decisive variables.

Jan 1, 1977

By Raymond Mancha

The number of installations of propeller mine fans completed during the years of 1936 and 1937 is evidence of the increasing popularity of the propeller fan with the American mining industry. During the period from 1931 to 1936, there were several different low-pressure, low-efficiency propeller fans available, which filled a definite need in replacing inefficient centrifugal fans operated at comparatively low pressure by means of purchased power. Since 1936, however, the trend toward the propeller fan has greatly increased, as propeller fans are now available practically without pressure limitations and capable of efficiencies high enough to warrant replacement of efficient centrifugal fans in many instances. Few manufacturers of propeller mine fans base their fan-operating characteristics upon similar test methods, primarily because of inadequate facilities for testing in the factory and the need of a test code incorporating a calibrated duct or nozzle that makes possible the testing of large propeller fans quickly, accurately and without prohibitive expense and space requirements. As a result, fan manufacturers have resorted to various methods for testing large propeller fans in the factory, and different yardsticks have produced uncomparable and often inaccurate performance data. It is the purpose of this paper to describe and discuss in detail the test procedure of the Jeffrey Manufacturing Co., which has been proved both accurate and practical. Fig. 1 shows a plan, a side elevation and two end elevations of the test duct with a propeller fan of the exhaust type in place. Testing propeller fans exhausting permits greater accuracy than testing these fans blowing, because in the former uniform flow conditions are more easily established at Pitot tube stations where fan pressure and air-volume measurements are desired. Any residual rotation remaining in the air discharged from a propeller fan blowing into a test duct must be removed before an attempt is made to obtain accurate pressure and volume readings. Although various devices for straightening the air may be placed between the blowing fan and the volume-measuring station without resulting complications, uniform flow so obtained at the pressure-measuring station necessitates corrective calculations to compensate for duct resistance

Jan 1, 1940

By Raymond Mancha

The number of installations of propeller mine fans completed during the years of 1936 and 1937 is evidence of the increasing popularity of the propeller fan with the American mining industry. During the period from 1931 to 1936, there were several different low-pressure, low-efficiency propeller fans available, which filled a definite need in replacing inefficient centrifugal fans operated at comparatively low pressure by means of purchased power. Since 1936, however, the trend toward the propeller fan has greatly increased, as propeller fans are now available practically without pressure limitations and capable of efficiencies high enough to warrant replacement of efficient centrifugal fans in many instances. Few manufacturers of propeller mine fans base their fan-operating characteristics upon similar test methods, primarily because of inadequate facilities for testing in the factory and the need of a test code incorporating a calibrated duct or nozzle that makes possible the testing of large propeller fans quickly, accurately and without prohibitive expense and space requirements. As a result, fan manufacturers have resorted to various methods for testing large propeller fans in the factory, and different yardsticks have produced uncomparable and often inaccurate performance data. It is the purpose of this paper to describe and discuss in detail the test procedure of the Jeffrey Manufacturing Co., which has been proved both accurate and practical. Fig. 1 shows a plan, a side elevation and two end elevations of the test duct with a propeller fan of the exhaust type in place. Testing propeller fans exhausting permits greater accuracy than testing these fans blowing, because in the former uniform flow conditions are more easily established at Pitot tube stations where fan pressure and air-volume measurements are desired. Any residual rotation remaining in the air discharged from a propeller fan blowing into a test duct must be removed before an attempt is made to obtain accurate pressure and volume readings. Although various devices for straightening the air may be placed between the blowing fan and the volume-measuring station without resulting complications, uniform flow so obtained at the pressure-measuring station necessitates corrective calculations to compensate for duct resistance

Jan 1, 1940

By R. M. Treco

THE purpose of this work has been to investigate recrystallization characteristics of zirconium after cold working and annealing. In order to do this, hafnium-contain ing crystal bars of Foote Mineral Co. iodide zirconium were selected for high purity. maximum diameter (about ½ in.), brightness of surface, and absence of core wire. A typical lot analysis is shown in Table I. In order to obtain uniformity of starting material, all bars were cold-swaged to 0.310 in. diam, annealed for 2 hr at 1000°C, and furnace cooled.

Jan 1, 1957

By J. S. Levine, M. Prats

Several methods are available for calculating the performance of solution-gas-drive reservoirs from the PVT properties of the oil and from the relative permeability and other properties of the formation. These methods require a number of simplifying assumptions. The present method of computation has made use of a high-speed computer to solve simultaneously the nonlinear partial differential equations that describe two-phase flow by solution-gas drive in order to calculate the performance of a reservoir. Some of the results obtained by the nonlinear partial differential equation solution are compared with those obtained with an approximate method, which has been called the semisteady-state solution. The pressure and saturation profiles from the wellbore to outer boundary calculated by the two methods are compared for one constant-terminal-rate case and two constant-teminal-pressure cases. The agreement in these profiles, as well as in the values of average reservoir pressure and cumulative recovery, leads to the conclusion that, for most engineering calculations, the semisteady-state method will give a reasonable approximation to the numerical solution of the differential equations describing solution-gas drive. An unfavorable (as regards ultimate oil production) set of relative permeability curves was used in the calculations in the belief that the effect of the parameters which were studied would be emphasized to a greater degree. Furthermore, the reservoir was assumed to be completely homogeneous, and these results should not be considered applicable to any other type of reservoir. Gravity effects are not considered. The absolute permeability was varied from 25 to 0.5 md. At an economic limit of 2 B/D, the recovery for a 25-md reservoir is about 1.8 times as great as that for a 0.5-md reservoir. The effect of permeability on the producing gas-oil ratio is minor. Once PVT properties of the oil and the relative penneability properties of the reservoir are fixed, the pro- during gas-oil ratio is found to be a function of the fraction of oil recovered. Well spacings of 10, 40 and 80 acres were considered. For the assumed homogeneous-reservoir properties, the effect of spacing on recovery at an economic limit of 2 B/D was very slight. Certain dimensionless groups can be used to extend the results to other fields having different penneabilities, spacings, reservoir thicknesses, well radii and porosities, so long as the PVT and relative permeability properties are similar to those used in this paper. INTRODUCTION An important aspect of reservoir engineering is the prediction of the performance of the reservoir based on the limited information normally available early in the life of a field. Usually, soon after a field has been discovered, it is necessary to decide upon the spacing to be employed and the production program to be used for most efficient utilization of reservoir energy. Where these decisions have not been dictated by legal or political considerations, they have frequently been based on experience factors which indicate that two fields with similar characteristics will probably have similar performances. To the extent that the industry has been successful in economically exploiting oil reservoirs, this rule-of-thumb method has been found to have merit. A large amount of theory has been developed with which it is possible to predict the performance of a reservoir by using certain known properties of the oil and the formation. Because of the difficulties of the mathematics involved for a drainage area having square or rectangular boundaries, the problem usually has been simplified and idealized by assuming each drainage area to have radial symmetry and the field to be represented by a number of these drainage areas. Muskatl was one of the first to formulate the theory for two-phase flow and to solve the equations for a few cases by numerical integration, using the relatively slow means of computing available at that time. His equations describing

INCREASING realization that pouring and ingot-mold practices involve many factors of fundamental importance to ingot quality and general steel-mill operations has caused these phases of steelmaking to become major concerns of operators and metallurgists engaged in control of quality and costs. Methods of pouring steel from the ladle into the ingot molds have some direct effects on ingot quality. The mold itself governs solidification and dimensions of the ingot and in so doing exerts some very tangible influences not only on ingot quality but also on product yields and general steel-mill processing. In addition, practices are employed' in the handling of molds during daily open-hearth operations that are important to quality and production costs. Therefore, pouring and mold practices must be considered highly specialized and important steps in steel-mill operations. MOLD DESIGN Mold design is difficult to discuss in a precise manner because it varies greatly throughout the industry, both in theoretical concepts and practical application, and few well developed data are available. Most ingot molds are designed to meet conditions peculiar to a given plant wherein quality standards are dictated by end-use requirements, which may differ considerably, even for the same grade of steel. The mold designer must also consider the equipment available to process ingots and the product obtained from them. Such equipment, used for stripping, heating, blooming and finishing operations, is seldom, if ever, exactly the same in any two steel plants. Thus, pronounced contrasts in mold designs can be expected to continue, even among plants making strictly comparable types of product, particularly because some producers are just beginning to realize the benefits possible from specialized designs. Certain fundamentals are used in mold design but even these

Jan 1, 1951

By A. A. Watts, R. I. Jaffee, F. C. Holden, H. R. Ogden

Hypoeutectoid Ti-Cu alloys are responsive to heat treatment, and considerable variation of mechanical properties may be produced by transformation of the ß phase. Control of cooling rate, isothermal transformation, or quench tempering determine the transformation structure and properties. The transformation products are similar to those of carbon steel. THE equilibrium diagram for the Ti-Cu system has been studied by various investigators, and the most recent diagram is that determined by Jou-kainen, Grant, and Floe.' The titanium-rich portion of this diagram is reproduced in Fig. 1. The alloy compositions and annealing temperatures used in this work are shown. The Ti-Cu alloys containing up to 17 wt pct Cu are representative of an active eutectoid alloy system. Joukainen et a1.l have stated that ß phase cannot be retained on quenching and this has been confirmed in the present work. The similarity between the Ti-Cu system and the Fe-C system is evident and, as will be shown later, many of the transformation products appear to have similar microstructures. Heat treatments in this program were designed to produce the structures of primary interest for study and determination of mechanical properties. Experimental Procedures Preparation of Alloys: Five ½ lb ingots, ranging in composition from 0.8 to 6.83 pct Cu, were prepared by double arc melting in an atmosphere of high purity argon. Titanium melting stock was obtained from high purity iodide titanium, and copper additions were made from copper wire clippings. Segregation was reduced by inversion melting, in which the once-melted ingots were inverted in the crucible and remelted. The double-melted ingots were forged at 1600°F to ¾ in. diam rods, with both heating and forging operations being carried out in air. Surface scale was removed by grit blasting and grinding, after which the forgings were vacuum annealed at 900°C. The alloys then were swaged to ¾ in. diam rod at 750°C and test specimens were cut from this material. The vacuum annealing operation was to remove dissolved hydrogen, which is commonly present in the iodide titanium as-received. Although vacuum fusion analyses were not obtained for all these alloys, past experience indicates that the 6 hr treatment with a limiting pressure of 10- to 10-5 mm of Hg is sufficient to reduce the hydrogen level to 10 to 30 ppm. Vacuum fusion analysis of the 0.8 pct Cu alloy showed 19 ppm of hydrogen. In addition to the five hypoeutectoid alloys, three 15 g ingots were prepared with nominal copper additions of 9, 10, and 11 pct. Fabrication procedures were similar, except that these alloys were rolled to 0.040 in. sheet. Microstructure specimens only were obtained. Table I shows analyzed compositions and fabrication temperatures for these alloys. Heat Treatments: All heat treatments were made in potentiometer-controlled, resistance-wound tube

Jan 1, 1956

By Henry M. Bates, Roscoe Pound

Mr. Chairman and Gentlemen: I accepted your Chairman's invitation to speak to a group of experts in this field with the greatest hesitation, because I know little or nothing about it. Certainly I can make no detailed suggestions, or suggest planning along very definite lines. You cannot do that sort of thing in a vacuum, and as I have suggested, my knowledge of the whole oil problem is next to nothing. It is possible that as a student of our public law, constitutional law particularly, for a number of years, I have acquired a perspective that may enable me to offer, for what they are worth, some general thoughts on these problems. I think that nothing in the whole field of law requires more definitely and clearly the functional approach than does the problem of a sound legal solution of the difficulties of the oil and gas industry. The industry is dealing with substances that are peculiar, and one must know how those substances act and what has been the history of the industry, to undertake to make anything like specific suggestions. I certainly am not qualified.

Jan 1, 1935

By John A. Church

When, in 1879,I examined the mines of the Tombstone Mill and Mining Company, at Tombstone, Arizona, I found a bed of tailings containing 12,000 tons, which had a value of 9 to 12 ounces of silver per ton and some gold. The ore had been amalgamated in pans, in which each charge had been ground for four hours, having been pre viously stamped through rough-punched screens, which gave a pro duct varying from 1-100th to 1-20th of an inch, according to the state of wear of the screen. It was certain that a large proportion of the tailings must be in fine slimes, and the question of recovering their value was difficult. Even now the concentration of slimes is . an unwelcome task, and at that day very little was known about it. Nevertheless, after considering the results of a test by repanning the tailings, I advised the company to concentrate and smelt, although they had to face the difficulty of making a smelting-product from slimes containing only 3 per cent. of lead. Limestone was abundant enough, but no iron suitable for flux was to be had for hundreds of miles. One of the company's claims con tained an argeutiferous manganese-ore, which gave but poor results by amalgamation. This was one reason for recommending smelt ing ; for if manganese would play the part of a precipitant, as iron does, the company could smelt by combining two of its silver ores, without other flux than the small amount of lime that might be needed. At that time no smelter had ventured to trust manga nese as a precipitant, though large quantities of this ore containing silver were bought and used by custom-smelters, who looked upon the manganese solely as a basic flux for silica. I believe that no other furnace has been obliged to trust this metal, and that the man ganese practice of Tombstone remains unique among the records of smelting lead-ores in the shaft-furnace. The bright side of the problem was given by the fact that the mines were shallow and that the enterprise would at least begin with oxidized ores. The tailings contained about 85 per cent. of silica,

Jan 1, 1895

By R. C. Davis, R. F. Berry, G. W. White, B. T. O’Connell, L. A. Stacha

P,, and v, may now be solved for by trial and error between Eqs. 2 and 3, by assuming time approaching zero and equating PI, to P12. Observe that the pressure under the slug, P12 of Eq. 3, does not remain equal to the P1, at the valve in Eq. 2 as the slug proceeds up the hole. To plot the profile of pressure vs depth, it is necessary to express P12 in terms of P11. To do so, the extent to which the original submergence length S changes with respect to time must be analyzed. At the end of time t after injection, the actual value of L in Fig. 3 is The fall-back v,(t) is now distributed in the gas and exerts pressure on the bottom. This, in addition to the weight of the gas, amounts to the difference in pressures from point to point. With the average pressure profile calculable, a true numerical value for the average pressure in the tubing may be obtained. The value of v, must be obtained experimentally, and since v,, S and D are known, the basic Eq. 1 may be solved for the amount produced. Knowing P, and the actual volume of tubing occupied by gas (vat), it is possible to calculate the volume of gas at standard conditions which is present in the