Search Documents

By Orville R. Lyons

THE relative performance of coal washing equipment, or the effectiveness with which any type or make of equipment removes impurities from coal, has been most difficult to evaluate in the past. The most widely used yardstick is the Frazer and Yancey efficiency formula developed in 1922,1 but Yancey in a later article states that "washers treating coals of different density composition or operating at different densities of separation cannot be compared directly on the basis of this criterion."' Prior to and since 1922, a variety of other methods has been used for comparison purposes, including the distribution curve, the error area, and the "ecart probable" or probable error. Yancey and Geer in discussing these methods conclude, "Performance can be evaluated in a number of different ways, with the choice of the proper method to use being dictated by the objectives of the investigation and the data available."' It is true that performance can be evaluated in a variety of ways, but if the equipment is to be evaluated on an effectiveness basis, there should be only one universal comparison method. Varying methods have been used because one universal comparison method has not been found or developed. In the article previously quoted, Yancey and Geer state in clear terms the primary concept for a universal comparison method: "One of the simplest, and certainly one of the most obvious evaluations of washery performance is the quantity of sink material in the washed coal and the float material in the refuse. If the washery products are tested at the density at which the washing unit is operated, the sink in the washed coal and the float in the refuse represent material that has been misplaced." The quantity of misplaced material was used as a criterion of washery performance by Lincoln in 1913,8 by the United States Bureau of Mines in 1938,4 by Hancock in 1947,3 and by the national French research agency Cerchar in recent years.2 In 1950 Anderson' proposed the use of this criterion as an efficiency value to replace the Frazer and Yancey formula. However, none of the above-mentioned investigators used the misplaced material concept in a manner that would provide universal coal-cleaning equipment comparisons. The Correlation Theory The ideal coal cleaning process would treat all sizes and would make a perfect separation at any given specific gravity. All material lower in density than the desired value would report in the coal product and all material higher in density would report in the refuse product. Unfortunately, no known cleaning process achieves this goal and there seems little likelihood that any process yet to be invented will do more than approach it. When coal is treated in volume under operating conditions, it is impossible to avoid mechanical entrapment, fluctuations in throughput and effective gravity of separation, and the creation of turbulent currents, even when a true heavy-liquid bath is used and the feed is closely sized and contains little intermediate gravity material. This being so, it is possible to appreciate the difficulties inherent in trying to obtain a perfect separation when treating a wide range of sizes and a feed containing high percentages of intermediate material, using turbulent currents to help create the effective separation gravity, under operating conditions which normally tend to be on the overload side. When coal is separated from refuse in any coal cleaning equipment, some refuse always reports to the coal and some coal to the refuse; the writer therefore assumed that there should be a relationship between the total amount of misplaced material produced by any given piece of equipment and the difficulty of separation as represented by the percentage of near gravity material in the feed. With small amounts of near gravity or ±0.1 material in the feed there should be less misplacement of material than would occur with large amounts of near

Jan 1, 1952

By T. B. Massalski, C. S. Barett

THAT metals and alloys of the body-centered-cubic structure tend to become unstable at low temperatures is so nearly universal that any exceptions are worthy of special attention. Studies of the exceptions may disclose unrecognized examples of metastability or may shed light on the nature of some of the factors that stabilize the body-centered-cubic phase. Among the structurally analogous body-centered-cubic 3/2 electron compounds, the ß-phase in the Cu-Zn system deserves further attention for, although this phase is known to undergo partial mar-tensitic transformation on cooling below room temperature to the temperature of liquid nitrogen when the composition is less than about 42 wt pct Zn, it does not transform on cooling .when there is more than this amount of zinc present.1-4 The present authors recently found that an alloy containing 48.35 wt pct Zn could be transformed, however, if deformed severely at room temperature or lower temperatures.V his discovery led to the suggestion that the jerky flow of ß-brass single crystals6 and some of the unusual temperature variations of the yield strength and hardness are due to strain-induced transformation during the tensile tests. The present investigation is an extension of that work to cover the entire available range of compositions of Cu-Zn ß-phase alloys and certain interesting compositions of the ß-phase in the Cu-Zn-Ga system. Particular attention is given to the structure of the transformation product resulting from cold work, which is found to vary with alloy composition, and to the temperature range in which transformation can be induced in the various alloys. The composition limits of the body-centered-cubic phase in the Cu-Zn system, based on a recent review by Raynor7 and the precision determinations of Beck and Smith: are shown in Fig. la; in the ß region the alloys are disordered and in the ß region they are ordered. The rate of ordering is so rapid that a high degree of order is found in any of these alloys immediately after quenching. Experimental The nine binary and four ternary alloys of this investigation were prepared from cathode copper (99.99 pct purity), electrolytic zinc (99.99+ pct), and gallium (99.98+ pct). All alloys were cast in transparent Vycor tubing, homogenized at temperatures between 800° and 890°C, and quenched in water. Ternary alloys were cast in small amounts (-5 g) to predetermined compositions to fall along a line of constant electron concentration in the ternary system. Changes of weight during the casting operation of the ternary alloys were not greater than 1 part in 2500 from the intended nominal weights and therefore their compositions were accepted without chemical analyses. All binary alloys were cast in larger amounts (100 to 150 g), homogenized, and hot rolled after preheating to 800°C. The central portion of the rolled strip of each alloy was annealed for eight days and quenched in brine. All binary alloys were analyzed chemically. The compositions, heat treatments, and metallographic appearances of all alloys are tabulated in Table I. Various samples were subjected to heat treatment or cold work at several temperatures and were then examined metallographically or by means of X-rays. Specimens about 6x6x3 mm in size were examined metallographic ally to confirm the presence of the ß-phase after quenching. Cold work was introduced by fastening each sample between two pieces of steel, cooling the assembly to the desired temperature, and transfering it rapidly to a vise where moderate or severe compression was immediately applied. Cold working at liquid helium temperature was done by a chisel-shaped tool mounted on an X-ray spectrometer, described elsewhere.% A!! metal-

Jan 1, 1958

By D. D. Pollock

Many constitution diagrams do not indicate the limits oJ solid solubility of the silver-rich solid solutions below 200°C. Thermoelectric measurements were employed to determine this limit in the nieighborhood of room temperature. The appearance of a second phase causes a discontinuity to occur in the tkevtrroelectric power as a function of cornposition at constant temperature and pressure. This discontinuity was employed to determine the limits of the silver-rich terzinal solid solutions of the Ag-A l, Ag-As, Ag- Bi, Ag--Ge, Ag-In, Ag-Pb, Ag-Sb, and Ag-Sn systenls at 30°C. CONSIDERABLE work has been done on the constitution of binary alloys of silver. The available data have been compiled by Hansen1 and Elliott.2 However, many of the binary diagrams do not show the limits of solid solubility of the silver-rich solutions below about 200° C. This work was undertaken in an attempt to extend these limits to the neighborhood of room temperature . PREPARATION OF ALLOYS All of the alloys were made with silver containing less than 0.014 pct (by weight) of impurities. The materials were weighed out into 225-g heats and melted in a high-frequency induction furnace. The indium, tin, and antimony alloys were melted in A1203 crucibles, under a boric anhydride cover, and were poured into split graphite finger molds. The aluminum, germanium, arsenic, lead, and bismuth alloys were melted in machined graphite crucibles; they were also covered with boric anhydride and poured into split graphite finger molds. The $-in.-diam ingots were heated to 750°C and were forged and hot-rolled down to 0.1 by 0.1 in. The wires were pickled in a 25 pct HNO3-75 pct H2O solution to remove any oxygen-rich surfaces. The wires were then annealed at 550°C for 2 hr in a dissociated ammonia atmosphere. They were then furnace-cooled for 20 hr to room temperature in this atmosphere. The wires were cold-drawn to 0.0808 in. diam. The finished wires were again annealed at 550°C in the same manner as in the first anneal. Thermoelectric Power. The thermoelectric power of a single specimen of each alloy was determined against pure silver which contained a maximum impurity content of 0.014 pct by weight. The wire specimens were straightened and then cleaned with ethyl alcohol. They were then reannealed in the same way as the finished wires to assure that any residual stress would be at a minimum level. Previous work has shown that the presence of small amounts of stress has the effect of decreasing the thermoelectric power. The alloy specimen was soldered to the pure silver wire to form the measuring junction. A standard set of copper leads was then soldered to the reference junctions of the thermocouple. These junctions were maintained in separate dewar flasks which contained finely shaved melting ice during the test. The thermal electromotive forces of the thermocouples were measured at four temperatures between 15° and 45°C. A known source of electromotive force was balanced against the output of the thermocouple until a null balance was reached. The data were then expressed in terms of the thermoelectric power at 30°C. The results were then converted to absolute thermoelectric power, s303.3 These data have an average error of less than ±0.2 pct. RESULTS AND DISCUSSION All of the experimental data are given in Table 11. Since the electromotive forces of the binary alloys of silver were determined against the pure silver from which they were made, the resultant thermoelectric powers are only a function of the intentionally added binary elements at the constant test temperatures. This provides a direct measure of the effects of the alloying elements. The absolute thermoelectric power of an alloy of silver is given4 by:

Jan 1, 1968

By C. Chu

A theoretical investigation has been made of the forward combustion process using a one-dimensional linear mathematical model, taking into consideration the effect of the vaporization-condensation which occurs on the leading edge of the heat wave. This work involves the solution of five coupled partial differential equations. Besides the vaporization-condensation phenomenon, these equations account for conduction, convection, combustion, heat loss, diffusion and bulk fluid flow. For the one-dimensional linear model studied, the vaporization-condensation phenomenon does not induce appreciable change in the temperature at the combustion front; and its primary effect is to create a steam plateau and to increase the length of the heated zone ahead of the combustion front. This effect becomes more pronounced at lower pressures, higher porosities or reduced gas saturations. The peak temperature and the temperature profile on the leading edge of the heat wave stabilize after a certain period. The length of the steam bank remains practically constant, although the length of the water bank increases as the heat wave advances. INTRODUCTION The existence of the vaporization-condensation phenomenon in the heat-wave process and the important role played by the phenomenon have been recognized by several investigators. Kuhn and Kochl stated that steam plateaus were frequently observed on the temperature records of their experiments. The steam plateaus were attributed primarily to the vaporization and subsequent condensation of the interstitial water existing in the oil sand. Szasz2 suggested that both lighter hydrocarbons and water are vaporized on the leading edge of the heat wave, carried forward in the gas stream, and then condensed to create banks of oil and water. Martin et al suggested that the vaporization-condensation phenomenon is one of the main mechanisms of the heat-wave process, along with thermal expansion and viscosity reduction. Wilson et al. reported the existence of a steam plateau several inches in length in their small-scale tube-run experiments. However, this important phenomenon has never been taken into consideration in the numerous theoretical analyses by various authors. 5 The purpose of this work was to study the thermal aspects of a linear heat wave, taking into consideration the vaporization-condensation on the leading edge of the wave, to determine the effect of this phenomenon on the temperature profile of the reservoir, and to investigate how this effect varies when other process variables are changed. THEORY We consider a reservoir of porous medium of cross-sectional area A, extending from x = 0 to x = L. This reservoir contains, aside from the solid matrix itself, a gas phase and a "combined liquid phase" which is a combination of two immiscible liquid phases — namely, an oil phase and a water phase. The oil present in the reservoir is assumed to consist of three fractions, a noncondensable gas, a nondistillable residuum, and a vaporizable oil fraction which may be present in both the gas phase and liquid phase. Before the heat-wave process begins, preheating has taken place and has imparted an initial temperature distribution T,(x) to the reservoir. At the start of the process, a stream of oxygen-bearing gas is introduced through the face at x = 0. This gas supports the combustion of the residual fuel and supplies the heat throughout the process. In order to develop a tractable system of equations, the model properties are postulated as follows: (1) the system is isotropic and homogeneous; (2) there is a uniform fuel content throughout the reservoir; (3) combustion takes place in a moving vertical planar region of infinitesimal thickness; (4) the temperatures of the fluids and the solid matrix are identical; (5) radiation is negligible; (6) the gas and liquid saturations are uniform throughout the reservoir and remain unchanged

Jan 1, 1965

By Charles Catlett

AN examination of the census reports' for 1880, which contain a large number of complete analyses of typical American iron-ores, indicates that the existence of barium sulphate in intimate association with iron-ore is rather unusual. Of 94 analyses reported there, but four show any barium sulphate, and the maximum content amounts to 3.04 per cent. The note of the occurrence of considerable quantities of barite in connection with certain iron-ores found in the Pinar del Rio Province of Cuba may be of interest. These deposits are found near the little village of Francisco, about 25 miles west of the city of Pinar del Rio on the Western Railroad of Havana. The principal ridges are anticlines, and consist of very thick deposits of sandy shales and slates containing a large number of little veins of white quartz which, by the gradual disintegration of the mass of the material, is left covering the surface. This quartz occasionally shows sulphide, but is generally barren of any such indication. At times lenticular masses of a more or less pure limestone were observed in these slates. The shales, which are of light color, are occasionally talcose. The formation would tentatively be classed as the Lower Cambrian, and the heavy ridges of comparatively horizontal limestone found in the anticlinal valleys as the Upper Cambrian. Along the crest of these slaty ridges deposits of iron-ore are found which are apparently in place, and were probably formed by replacement of masses of limestone similar to those noted elsewhere. The ready disintegration of the slates, and the

Jul 1, 1907

By R. M. Goldhoff, H. J. Beattie

The high-temperature properties of a 1 Cr-Mo-V forging steel are described. A series of controlled heat treatments was designed to delineate the effects of austenitizing and tempering treatments, temile strength, and grain size on such properties. Studies indicate that the mechanical properties and their varlations under creep can be described by the initial metallurgical structures and their changes droPirzg exposure, particulavly the carbide reactions. Such structures are described and correlated with the mechanical properties. FOR many years the large steam turbine industry has relied on the 1 Cr-Mo-V type forging steel for critical applications. Because of its adequate heat resistance and relative economy, it is currently in use in the temperature range up to about 1050" to 1075°F. Attempts to understand the large property variations attainable in this steel involve the structural modifications due to the wide latitude in its heat treatment. The heat treatment essentially involves a two-step process which includes solution-ing of carbides in the austenite range followed by a suitable tempering treatment below the critical to adjust the level of properties. The latter step is referred to as "secondary hardening" and is basically an ordinary aging reaction involving carbides. In the commercial heat treatment of large components of such steel, homogenizing and stress-relief anneals may be included and have some importance in determining subsequent properties. Several studies of the engineering properties of this steel as a function of transformation micro-structure have been reported.1 3 However, in this steel the carbide reactions, which are a function of composition and heat treatment, appear to be the property-controlling factor rather than the micro-structure defined as a transformation product. Thus, the tempering resistance of this type of alloy steel is mainly a function of the size and distribution of alloy carbides.4 However, it is also necessary to consider the stability of the microstructure and the effect of dynamic carbide reactions on subsequent properties. It is the purpose of this paper to show the interdependence of properties and corresponding structures, particularly carbide reactions, developed for a limited set of controlled heat-treatment conditions applied to 1 Cr-Mo-V steel. MATERIALS AND PROCEDURE The material for this work came from a large production forging whose chemical composition is shown in Table I. The property data accumulated on this steel as a function of heat treatment were room-temperature tensile and smooth- and notch-bar creep rupture at 1050°F (notch geometry: shank diameter = 0.357 in., depth = 50 pct, radius = 0.005 in.). To achieve controlled structural variations the temperature and time of both austenitizing and tempering were varied in a manner to produce a series of eight steels each at one of two grain sizes and one of two hardness levels in proper combination for valid comparisons. This will be clear upon examination of Table I. Structural studies involved the use of optical and electron microscopy as well as X-ray and selected-area electron diffraction. To reveal the nature of carbide precipitations, electrolytic extraction techniques were used with subsequent analysis of the residue by X-ray diffraction. Weight losses of the steel specimens during electrolysis were measured and successive chemical fractionations of the residues were applied and checked by X-ray examination. The details of fine structural distributions, morphologies, and crystallography of the precipitates as well as dislocation distributions were investigated by examining in the electron microscope three common types of preparation. a) Relief Replicas. Mechanically polished sections were etched in 2 pct nital, replicated with a nitrocellulose film, which was shadowed by chromium vapor deposited at a glancing angle of 20 deg. b) Extraction Replicas. A thin film of carbon was vapor-deposited on the polished and etched surface. The carbon films were then etched off and gathered on electron-microscope supporting grids. The carbides left imbedded in the carbon replica in their original distribution were then examined crystallo-graphically by selected-area electron diffraction. c) Thin Films. Specimens were mechanically ground and polished down to a thickness of 0.001 to 0.003 in. Final thinning was done electrolytically in a "chrome-acetic" electrolyte. When holes began to appear in the foil, the voltage was interrupted and applied in several 1-sec bursts. Sections of the foil between holes were thin enough to pass a 100-kv electron beam that carries an image.

Jan 1, 1965

Jan 1, 1905

By K. A. Jackson, G. A. Chadwick, A. Klugert

The diffusion field ahead of a lamellar interfnce is analyzed using an electrical analog. A self-consistent solution is obtained for the shape of the interfnce and the diffusion field by an iterative process. The solutions presented here are for a 50-50 eutectoid or eutectic, The shape of the interface is found to he independent of growth velocity and lamellar spacing, and to depend on the relative values of interfacial free energies at the phase houndaries . The mode of growth of lamellar eutectics and eutectoids has been a subject of much interest for many years.1-4 Mehl and Hagel 1 have shown photomicrographs taken by Tardif when he attempted to determine experimentally the shape of an advancing pearlite interface; the results are completely ambiguous. Brandt' and schei13 have made approximate calculations of the composition ahead of a lamellar growth front. The shape of the advancing front and the composition distribution ahead of the front are difficult to calculate because one depends on the other. It is the purpose of the present paper to describe a method by which this calculation has been done. Lamellar-eutectic growth usually occurs under conditions where the growth is fairly rapid, and the interface temperature is close to the eutectic temperature. The growth rate is usually determined by heat flow. Eutectoid growth, on the other hand, can best be studied by quenching to some temperature, and allowing growth to proceed isother-mally. In both cases the growth is believed to be controlled by diffusion* rather than by the atomic kinetics of the transformation. This being the case, a single treatment of the diffusion equation will apply to both cases, provided the region of the interface in a eutectic may be considered to be isothermal. If a part of the interface could appreciably change its thermodynamic driving force by advancing ahead of or lagging behind the mean interface, then the two cases would not be similar. Eutectics normally grow in temperature gradients of the or-der of a few degrees per centimeter. The normal eutectic spacing is the order of a few microns. Part of the interface would have to extend many lamellar spacings ahead of the mean interface before it experienced sensibly different conditions. The interface temperature is usually a few tenths of a degree below the eutectic temperature so that temperature differences of the order of one-thousandths of a degree (a displacement of one lamellar spacing) would be unimportant. Protrusions large compared to the mean spacing do occur when one phase only grows into a eutectic liquid. This is usually a dendritic type of growth, and easily distinguishable from the lamellar mode of growth. A single treatment of lamellar growth will apply equally well to both eutectic and eutectoid decomposition. At the interface, which as shown above is essentially isothermal, the difference between the equilibrium eutectic temperature Teu and the actual interface temperature Ti, can be divided into two parts: 1) the composition varies across the interface, so that the local equilibrium temperature is not Teu; and 2) the interface is curved, so that the local equilibrium temperature is depressed according to the Gibbs-Thompson relationship. This undercooling can be written as Teu-Ti =?T = mAC(x) + a/r(x) [1] where ?C(X) is the departure of the composition at a point x on the interface from the eutectic composition, see Fig. 1, r(x) is the local radius of curvature at a point x on the interface, m is the slope of the liquidus line on the phase diagram, and a is a constant given by where s is the interfacial free energy, TE is the equilibrium temperature, and L is the latent heat of fusion. The calculations in this paper will be made only for the case where the phase diagram is symmetric, that is, the eutectic occurs at 50 pct, the liquidi have the same magnitude slope m at the eutectic temperature, and C,, the amount of B rejected when unit volume of a freezes, see Fig. 2(a), is the same for both phases. As shown in Fig. 2(b), the composition ahead of the a phase will be rich in B, the composition ahead of the ß phase will be rich in A. The composition at the phase boundary is the eutectic composition. The difference between the local liquidus temperature and the actual tempera-

Jan 1, 1964

By J. D. Mote, J. E. Dorn

This investigation was undertaken to study the effects of piledup arrays of dislocations on inducing slip, twinning, and fracturing in magnesium bicrystals. A series of variously oriented bicrystals of magnesium having a vertical grain boundary were prepared and tested in tension. It was found that piled-up arrays of dislocations at the grain boundary could, under appropriate conditions, induce slip, twinning- and cracking. The results that were obtained substantiate, at least qualitatively, the general dislocation mechanism for transmission of strain across grain boundaries and the Petch-Stroh concept of fracturing. WHEREAS single crystals of magnesium generally exhibit extensive deformation, coarse-grained poly-crystalline magnesium at subatmospheric temperatures fractures after a few percent elongation.' Although a small amount of ductility is obtained, several features of this fracturing are characteristic of typical brittle behavior. Over a rather broad temperature range the fracture stress is insensitive to the test temperature and the fracture stress increases linearly with the reciprocal of the square root of the mean grain diameter. The course of fracturing is predominantly intergranular, but small fragments of adjacent grains frequently adhere to the fractured surface.2 The brittle behavior of polycrystalline magnesium is attributable to the limited number of facile deformation mechanisms it exhibits at low temperatures. For a general deformation of a randomly oriented polycrystalline aggregate, each grain must exhibit at least five independent mechanisms of deformation to permit accommodation of the imposed deformation from grain to grain.= Although minor amounts of prismatic slip occur in corners of grains where stress concentrations are known to be high, glide in polycrystalline magnesium at low temperatures takes place almost exclusively by basal slip.' The common type of twinning, which takes place on the (1012) pyramidal planes, can under the most favorable orientations, lead to a. strain of only 6.9 pet; the contribution of twinning to the tensile strain would indeed be much less than this in a randomly oriented polycrystalline aggregate of magnesium. Since the three mechanisms of basal slip are coplanar, they are equivalent to only two independent mechanisms, a number insufficient for a general deformation. Consequently, once the permissible twinning has taken place in conjunction with basal slip, no further plastic deformation is possible because of interference to slip at the boundaries of dissimilarly oriented grains. At this stage brittle fracturing takes place due to high stress concentrations at the juncture of slip bands with the grain boundaries; the predominance of intergranular fracturing in magnesium, in preference to transcrystalline fracturing which is prevalent in zinc, has not yet been rationalized. A more atomistic description of the plastic behavior and fracture characteristics of magnesium follows from the analyses made by stroh4 on the stresses induced by piledup arrays of dislocations. Slip first takes place by dislocation motion in the most favorably oriented grains. As the dislocations approach the boundary of a dissimilarly oriented adjacent grain they begin to form an array of dislocations with its attendant stress field. Piledup arrays of screw and edge dislocations introduce high localized shear stresses at the spur of the array; piledup arrays of edge dislocations also induce high tensile stresses localized in the vicinity of the grain boundary. Whereas the shear stresses can induce slip to take place, the tensile stresses, if sufficiently high, can cause fracturing. The localized shear stress will be relieved if sufficient numbers of mechanisms of deformation become operative in the original and the adjacent grain to permit accommodation of the dislocations in the grain boundary. In this event a ductile behavior will be obtained. But if the number of deformation mechanisms is insufficient for complete migration of dislocation arrays into the grain boundary, the tensile stresses due to the edge components of piledup dislocation arrays will continue to increase with increasing applied stress until fracturing takes place. Whereas face-centered-cubic metals have a sufficient number of mechanisms of slip for accommodation of dislocations in their grain boundaries to exhibit ductile behavior, hexagonal-close-packed metals, in general, do not. Consequently, hexagonal-close-packed metals are usually brittle except when conditions such as alloying or temperature permit facile slip by a number of mechanisms. The arguments presented above suggest that the mechanical behavior of magnesium depends on whether or not dislocation arrays in adjacent grains can enter the grain boundary. When such accommodation is possible, ductile behavior is expected; but when such accommodation is impossible, fracturing will ensue. To further test the validity of these arguments it was considered advisable to study the

Jan 1, 1961

By P. M. Robinson, J. S. LI. Leach

The heats of solution oj' indiurrr, tin, lend, nrzd tellurium have been calculated from the measured heat effects when mechanical mixtres of indium and telLuium tin and tellurium, and lead and tellurium were added to liquid bismuth. The results are in good agreement xith publislzed values.s for the separate sollction of each eleltzent in bismuth. The heats oj solution of cadmium and tellurium calculated from the rneasuved heat effects on adding trechanical mixtures of these elements do not ugree zc,itl the published values jbv the separate solution of each element. It is shown that at 623°K Ile interaction between cadmium and tellurium dissolved in liquid bismuth is strong enough to led lo preciPitation of solid CdTc. The heats oj- jor-mation of CdTe at 273" nd 623°K (1)-c crilculated fi-or the measured heat ejlfecls. The calcnlaled az'erage deviation from the Kopp-l\'ez?,zunrz rule fov solid CdTe is less than 0.06 cat per g-atom- C over this lertzperalure range. Tlze importance 0.f these oDserl.ations to the determination of heals of formation hy metal solution calorimetry is considered. LIQUID metal solution calorimetry is a convenient method for determining the heats of formation of solid compounds. In this technique the heat of formation is the difference between the measured heat effects on dissolution of the compounds and of mechanical mixtures of the components in the liquid metal.' The heat of solution of the mechanical mixture may be calculated from the measured heat effect. At infinite dilution of the solutes, this heat of solution is equal to the sum of the heats of solution of the separate components. If the heat of solution of one of the components is known, the value for the other can be derived; if both are known, they may be used to check the accuracy of the calorimetric technique. The heats of formation of the tellurides of cadmium, indium, tin, and lead have recently been measured by metal solution alorimetr. The heats of solution of indium, tin, lead, and tellurium at infinite dilution in liquid bismuth at 623"K, calculated from the measured heat effects on solution of the mechanical mixtures, are in good agreement with the published values. The heats of solution of cadmium and of tellurium calculated from the measured heat effect on solution in bismuth at 623'K of mechanical mixtures of cadmium and tellurium, however, do not agree with values estimated from the literature. 1) EXPERIMENTAL PROCEDURE AND RESULTS The Heats of Solution of Indium, Tin, Lead, and Tellurium in Bismuth. The heat effects were measured when mechanical mixtures corresponding to the compounds In,Te, InTe, In2Te3, In2Te5, SnTe, and PbTe were dissolved in bismuth. The calorimetric procedure and the method of calculation have been described elsewhere.' The heats of solution of the mechanical mixtures were obtained by subtracting the change in heat content per gram-atom of the sample between the addition temperature (273°K) and the bath temperature (623"K), (H623°K - H273°K)S, from the measured heat effects. The calorimeter was calibrated with pure bismuth. The reported values of the measured heat effects are based on (HGoK - ^273oK)Bi = 4.96 kcal per g-atom.3 The measured heat effects are found to be linear functions of the solute concentrations of the bath in the dilute solution range. The values, extrapolated to infinite dilution, are listed in Table I, together with the heats of solution of the mechanical mixtures calculated using the published values of (H 623°K - H273°k)s for indium, tin, lead,3 and tellrium. All the error limits quoted in this work represent the spread of values obtained. The heats of solution in liquid bismuth at 623°K of mechanical mixtures of indium and tellurium in four different proportions were determined. Values of the heats of solution of the two components were then calculated from the resulting four simultaneous equations: The heats of solution at infinite dilution of tin and lead in liquid bismuth at 623°K were calculated from the heats of solution of the mechanical mixtures of tin and tellurium and of lead and tellurium using the heat of solution of tellurium calculated above. These values of the heats of solution are listed in Table I1 together with some published values for comparison.

Jan 1, 1967

By R. K. Dann, L. W. Roberts, R. B. Benson

The mechanical properties of 300-series stainless steels were investigated in both high-pressure hydrogen and helium environments at ambient temperatures. An auslenitic steel which is unstable with respect to formation of strain-induced a (bee) and € (hcp) mar-tensile is embrittled when plastically strained in a hydrogen environment. A stable austenitic steel is not embriltled when tested under the same conditions. The presence of hydrogen causes embrittlement at the mar-lensitic structure and a definite change in the general fracture mode from a ductile to a quasicleavage type. The embrittled martensitic facets are surrounded by a more ductile type fracture which suggests that the presence of hydrogen initiates microcracks at the martensitic structure. If a steel is unstable with respecl to fortnation of strain induced martensile, plastic deformation in a hydrogen environment will produce rapid embrittlement of a notched specimen in comparison to an unnotched one. FERRITIC and martensitic steels can be embrittled by hydrogen that has been introduced into the alloys, either by thermal or cathodic charging prior to testing.1-5 However, conflicting reports exist as to whether austenitic steels that are stable or unstable with respect to formation of strain-induced martensite can be embrittled by hydrogen.8-12 A recent investigation has shown that cathodically-charged thin foils of a stable austenitic steel can be embrittled.13 An earlier investigation of a thermally charged 18-10 stainless steel revealed a significant decrease in the ductility only at the lowest test temperature of -78°C, although strain-induced bee martensite was shown to be present in one specimen tested at ambient temperatures.' When martensitic steels are tested in a hydrogen atmosphere, they are embrittled.'4-'7 It has been observed in this Laboratory that 304L steel, which is unstable with respect to formation of strain induced martensite, forms surface cracks when plastically strained in a high-pressure hydrogen environment. Work in progress elsewhere concurrent with this investigation has also established that 304L is embrittled when tested in a high-pressure hydrogen atmosphere." The objective of this investigation was to study the effect of a high-pressure hydrogen environment on the tensile properties of a stainless steel that contained strain-induced martensite (304L) and one that did not (310). EXPERIMENTAL TECHNIQUES Notched and unnotched cylindrical specimens were machined from 304L* and 310 rods that were heat- treated at 1000°C in argon for 1 hr followed by a water quench. The chemical analyses of these steels are given in Table I. The unnotched specimens had a reduced section diameter of 0.184 & 0.001 in., a gage length of 0.7 in., and were threaded with a 0.5-in.-diam. thread on each end. The notched specimens had a reduced section diameter of 0.260 * 0.001 in. and a 0.75-in. gage length, with a 30 pct 60 deg v-notch at the center. The notch had a maximum root radius of 0.002 in. The tensile bars were fractured in a hydrogen or helium atmosphere of 104 psi at ambient temperatures. The system used for mechanically testing the specimens is to be described in detail elsewhere.19 Several specimens of each type were tested in air using an Instron testing machine. The same yield strength and ultimate tensile strength were obtained in 104 psi helium with the above system as with the conventional testing machine. Magnetic analysis was employed to determine that there was a (bee) martensite in plastically deformed 304L and that it was not present in plastically deformed 310. The magnetic technique depended on allowing the material being studied to serve as the core between a primary and secondary coil. Thus, any change in the amount of magnetic material present between the annealed and plastically deformed steels will be indicated by corresponding changes in the induced voltage in the secondary circuit." The ratio of the output signal of a nonmagnetic stainless steel to a completely magnetic maraging steel was 2000 to I. Several unnotched 304L bars tested in hydrogen were analyzed for hydrogen by vacuum fusion analysis. There was an increase in the hydrogen content to approximately 2 ppm for the specimens tested in hydrogen, as compared to less than 1 ppm for the as-received material. Several thin sections cut from notched areas of 304L specimens tested in hydrogen and containing the fracture surface contained approximately 1.5 ppm H. The accuracy of these determinations was estimated to be ± 50 pct.

Jan 1, 1969

By William H. Breeding

The remarks that follow are based substantially on experience covering 45 years, 80% of which has been in placer work, rather than on a review of available literature. Most commercial placers have been deposited by the action of water. The richer and more- difficult-to-mine placers are those in the headwater areas where gradients are steepest. The most lucrative placers are generally in inter- mediate areas where volumes are greater, fewer boulders are present, and gradients are from 3% to 1-1/2%. The higher volume, lower grade placers are in the lower reaches of river systems where gradients are lower. Where gold-bearing rivers have discharged into the sea, wave action can concentrate values on beaches, past and present. Most of the rich, readily accessible placers were mined by our forefathers. Current opportunities exist: (1) in remote areas where infrastructure has been absent in the past, or development has been prohibited by adverse ownership - political or commercial; (2) in deposits that could not be mined by equipment available to our forefathers; (3) in deposits unidentified by our forefathers; (4) where the-price-of-product/cost ratio is substantially better than in earlier years; or (5) a combination of those factors. When I entered the placer business in the late 1930s, and subsequently, a prevailing opinion believed that glacial deposits should be avoided as irregular in mineral content and composition, and unrewarding to explore and develop; yet an operator has been mining a fluvio-glacial deposit profitably for the past 17 years. Rich buried placer channels, of ten called paleo-channels were worked in the last century, generally by hand methods, and under conditions that would be unacceptable today. Exploration and mining equipment now available make some of these channels attractive targets. Well-known examples are in California and Australia. The formation of a commercial placer requires a source of valuable minerals. Above primary deposits, there may be eluvial deposits formed by the erosion of gangue minerals and the concentration "in situ" of valuable minerals. Down slope from these deposits are the hillside or colluvial deposits, and below them are the alluvial deposits of redeposited material. Most of the great placer fields of the world are the result of several generations of erosion and deposition. Well-known examples are in California and Colombia. Gold is a very resistant and malleable material, and gold placers may extend for 64 or 80 km (40 or 50 miles) along a river system. Platinum is less malleable, but is very resistant to disintegration. Diamonds are extremely hard, and (especially gem diamonds) may be found over great lengths of a river system. Cassiterite is less resistant to disintegration, and tin placers seldom extend over two miles without resupply from an additional source or sources of mineralizaton. Tungsten minerals are generally more friable, and within a few hundred yards of the source disintegrate to the point that they are uneconomical to recover. Rutile, ilmenite and zircon placers generally result from the weathering of massive deposits, and may be encountered over extensive areas; most are fine grained and durable. What does a geologist or mining engineer look for in placer exploration? The old adage to look for a mine near an existing mine is still valid. You need a source of valuable mineral. Then you require conditions for concentration, which means a satisfactory gradient and/or other conditions that will permit heavy minerals to settle. Nicely riffled gravel, often called a shingling of the bars, is conducive to placer formation. Coarser gravel is logically associated with coarser gold. Excessive clay and/or high stream velocities in narrow channels can carry gold far downstream and distribute it uncommercially over a large area. When material is extremely fine, in situ weathering and concentration become more important. Placers frequently occur distant from lode mines, and one must remember that in a larger watershed the exceptional floods that occur once in a hundred or a thousand years can move great quantities of material long distances. The carrying power of water is said to vary with the fifth or sixth power of its velocity. I am not ready to disagree with Waldemar Lindgren and accept that many commercial placers are substantially enriched by the chemical deposition of gold from solutions; however, I have seen crystalline gold in clayey material quite distant from known sources of primary gold that is dif-

Jan 1, 1985

By D. L. Albright, R. W. Kraft

High-purity materials have been used in producing as-cast, controlled, colony, and degenerate solidification structures in the Fe-FeS eutectic. Experiments disclosed that this eutectic can be classified as normal and has a natural morphology composed of rodlike iron particles dispersed in a matrix of iron sulfide. The metallography of the various structures was studied, and a preferred crystallography was revealed in the controlled specimens produced by unidirectional solidification. The orientation effects found in these latter specimens are an [001] fiber texture in the -mowth direction of the bcc iron bhase and a texture corresponding to bicrystalline behavior in the hexagonal iron sulfide, with the growth direction near to (2111) poles. The observed texture of the iron phase is considered as indirect evidence that the alloy un-dercooled by at least 75°C before solidification. The unidirectional solidification of binary eutectic alloys has produced materials which exhibit a structure and properties markedly dependent upon the solidification process. In many cases a controlled microstructure with pronounced metallographic and crystallographic anisotropy can be experimentally achieved by proper regulation and balance of the growth rate of the alloy, the chemical purity of the starting materials, and the thermal gradient in the liquid at the liquid-solid interface. The purposes of this investigation were to produce various micro-structures in the Fe-FeS eutectic for subsequent study of their magnetic properties and to correlate the different structures with the solidification conditions in order to obtain a better understanding of the structure of eutectics. The Fe-S equilibrium diagram exhibits a eutectic composed of nearly pure iron and stoichiometric iron sulfide (FeS1.00), with the eutectic reaction occurring at 988°C and 31.0 wt pct S.1 Calculations indicate that this eutectic should solidify with about 9.5 vol pct Fe and 90.5 vol pct FeS, which in turn suggests2 that the micros tructure will consist of a rodlike iron constituent dispersed in a matrix of FeS. This characteristic has in fact been revealed some years ago.3 Thus, controlled solidification of this alloy might yield a material whose micromorphology would consist of very small ferromagnetic iron particles, rod-like in shape and aligned parallel to one another, supported in a matrix of antiferromagnetic FeS. Such specimens, because of the magnetic characteristics of the two phases, would be interesting subjects of study as magnetic materials. Hence the magnetic properties were considered in detail and are reported elsewhere.4 EXPERIMENTAL PROCEDURE The specimens of Fe-FeS eutectic were prepared from ultrapure iron (99.99+ pct) and high-purity sulfur (99.999+ pct). The iron was estimated to contain 60 ppm impurities (99.994 pct Fe) after zone purification.5 The ingots of iron were cut into chips, and the lumps of sulfur were ground into powder. In order to redice any nometallic impurities which might have accumulated during handling, the iron chips were annealed for 5 hr at 750° ± 10°C in a dry hydrogen atmosphere. Immediately after this treatment the chips were blended with the sulfur powder in eutectic proportions; the mixture was tamped into transparent fused quartz tubing and then vacuum-encapsulated under a pressure of 40 to 60µ of Hg. Because FeS expands upon solidification it was necessary to re-encapsulate the initial capsules so that oxidation reactions would be avoided when the inner tube cracked during solidification. For purposes of homogenizing the blended mixtures before solidification, the double capsules were heated to 750° ± 20°C and held for 20 hr; after this treatment the reacted product was weakly agglomerated. Each sample was then loaded into an apparatus for very rapid melting and freezing; this was accomplished by passing a molten zone through the specimen, using induction heating and a traverse mechanism. The resulting specimens solidified in the shape of the quartz tubing. Two sizes of specimens were used in this work, 18 mm diam by 100 mm long and 5 mm diam by 30 mm long. Metallographic examination of several ingots of both sizes after the above consolidation indicated no lack of compositional homogeneity and a random "as-cast" structure, because the travel rate was so rapid that unidirectional solidification was not achieved. Unidirectionally solidified specimens were resolidified in the apparatus shown schematically in Fig. 1, This equipment consisted of a kanthal resistance furnace mounted on the carriage of a zone-melting unit so that the heating element could traverse the length of the sample at a selected rate of speed. Large specimens were solidified with the mechanism tilted at ap-

Jan 1, 1967

By J. J. Kramer, K. Foster

The orientation distribution of surface-energy -induced secondary recrystallized grains was determined. This work was conducted on thin sheets of a 3 pct Si-Fe alloy annealed under environmental conditions that furor grouth of grains with a (100) plane in the surface of the sheet. The texture was found to be extremely sharp and almost independent of sheet thickness. The distribution varied exponentially with the angular deviation from the {100} plane. It was possible to relate the distribution to the nu-cleation rate of the secondary rains as influenced by the surface-energy difference. THE role of surface energy in the secondary grain growth of cube-oriented grains (grains with a (100) plane in the plane of the sheet) in thin Si-Fe sheets has been previously discussed.1-4 In high-purity sheet material normal grain growth usually occurs until the grains have extended through the sheet. Further grain growth is inhibited by the thermal grooving of the boundaries at the sheet surface. However, additional growth of cube grains can occur by a secondary grain growth process under conditions where the (100) plane has a lower surface energy than other orientations. Apparently for these alloys, cusps exist in the polar plot5 of surface free energy with the lowest cusp energy occurring at the (100) orientations. This has been reported to be the result of preferential adsorption of sulfur on the (100) planes.6 As a result of this process, a distribution of orientations could arise from two possible mechanisms. First, when a cusp is present in the polar plot of surface free energy, there are orientations inside the cusp that have a lower surface energy than elsewhere on the polar plot. Also, at sufficiently high temperatures, flat surfaces whose orientations are inside or just outside the cusp (depending on its shape) can often thermally etch, yielding a microscopically stepped surface of even lower surface energy. As a result, grains oriented close to cube would also have a lower surface free energy, either because of the cusp shape or by thermal etching, and could possibly grow as secondary grains by the surface-energy phenomenon. One should thus observe a distribution in the surface orientation of the cube grains comprising the secondary structure. It is the purpose of this paper to investigate this orientation distribution experimentally and to discuss the factors involved in its formation. For this purpose, the surface orientations of a large number of secondary grains in various sheet thickness were determined by means of the Laue back-reflection X-ray technique. PROCEDURE A vacuum-melted 3 pct Si-Fe alloy containing a nominal impurity content of 0.005 wt pct was processed into strip. A single cold-rolling step of 90 pct reduction was used for each strip regardless of the final sheet thickness. Final strip thicknesses of 0.60, 0.30, 0.15, and 0.075 mm were used. Care was taken to insure that the final strip surface was smooth and flat. All strips of a given thickness were annealed together at 1200°C in dry hydrogen (dew point -70°C) to develop the desired secondary structure and to insure identical environmental annealing conditions. The annealing time was selected to develop a complete secondary structure in the thinner sheets but to permit the thicker sheets (0.60 mm) to have residual primary grains remaining. This was necessary to determine whether growth impingement could lead to one secondary grain consuming another at a greater angular deviation. For the X-ray determination of the surface orientation of the secondary grains, a special specimen holder was used. The camera and holder arrangement could be aligned by X-raying a grain in three positions rotated 180 deg to each other. Thus, with a small beam X-ray focus (1 mm), the surface orientation of any grain could be determined to within one-half a degree. The surface orientations of one hundred cube secondary grains were determined for each sheet thickness. The criteria of a secondary grain were its size relative to the sheet thickness and the number of sides of the grain observed in the sheet surface. (A primary recrystallized grain extending through a sheet will generally have six edges visible in the plane of the sheet, whereas a secondary grain will have many more when growing entirely into primary grains.) Grains were selected as randomly as possible by X-raying every secondary grain found along a line drawn on the strip. No attempt was made to determine the exact orientation of the planes of the surface, as many strips from randomly selected sheets were used. On1y the angular deviation of the surface plane from {100} was measured. In order to assess the volume distribution in the

Jan 1, 1965

By David A. Thomas, David N. French

The lrnrdness of WC crystals has been measured with the Knoop indenter at loads of 100 and 500 g on the (0001) and (1070) planes. The hardness as tneasitred on the basal plane is 2400 kg per sq mm and shows little anisotropy. The hardness on the prism plane, however, shows a marked orientation dependence, with a low value of 1000 kg -per sq mm when the long axis of the Knoop indenter is oriented parallel to the c axis and a high value of 2400 kg per sq mm when the indenter is perpendicular to the c axis. Slip lines (Ire observed surrounding the microhardness indentations and they show slip on (1010) planes, probably in [0001] and (1120) directions. This slip behavior can be explained by the crystal structure of TVC, which is simple hexagonal with a c/a ralio of 0.976. The hardness anisotropy call be explained by [0001]{1010} and (1130) {10l0] slii) and the resolved shear-stress analysis of Daniels and Dunn. HARDNESS anisotropy is a well-known phenomenon and has been reported for many metals, with both cubic and hexagonal structure.1-6 For hexagonal tungsten carbide, WC, a wide range of hardness values is reported in the literature. For example, Schwarzkopf and Kieffer7 give a hardness of 2400 kg per sq mm and report a value of 2500 kg per sq mm by Hinnüber. Foster and coworkerss give the average Knoop microhardness as 1307 kg per sq mm with a maximum value of 2105 kg per sq mm. Although these values and the structure of WC suggest the likelihood of hardness anisotropy, no such measurements have been made. We first detected a large apparent hardness anisotropy in WC crystals about 75 p large, in over-sintered cemented tungsten carbide. Prominent slip lines also occurred around many indentations. This report presents further observations and interpretations of hardness anisotropy and slip in WC crystals obtained from Kennametal, Inc. Both Knoop and diamond pyramid indenters were used on a Wilson microhardness tester with loads of 100 and 500 g. EXPERIMENTAL RESULTS The carbide crystals tended to be triangular plates parallel to the (0001) basal plane of the hexagonal structure. The side faces were parallel to the ( 1010) prism planes. Specimens were mounted approximately parallel to these two types of faces and metallographically polished. Laue back-reflection X-ray patterns were used to orient the specimens, which werethen ground to within ±1 deg of the (0001) and (1010) planes. The Knoop hardness values measured on the basal plane are plotted in Fig. 1. There is only a small anisotropy, with a hardness range of 2240 to 2510 kg per sq mm. The additional points at angles from 52.5 to 67.5 deg confirm the sharp minimum hardness at 60-deg intervals, consistent with the sixfold hexagonal symmetry. The average hardness of all values obtained on the basal plane is 2400 kg per sq mm. While the basal plane shows only slight anisotropy, the (1010) plane exhibits marked hardness anisotropy, from 1000 to 2400 kg per sq mm. Fig. 2 shows the hardness as a function of the angle between the long axis of the indenter and the hexagonal c axis, the [0001] direction. The minimum and maximum occur when the indenter is oriented parallel and perpendicular to the [0001] direction, respectively. The anisotropy of the prism plane is contrary to that reported for hexagonal zinc and hard- However, the basal-plane anisotropy is similar to these two metals.1'2 To check the accuracy and reproducibility of the measurements, a series of fifteen impressions was made at 100-g load in the same orientation in the same area of the specimen surface. The average for all was 2040 kg per sq mm, with a range of 1950 to 2130 kg per sq mm, giving an accuracy of about ± 5 pct. Thus the slight anisotropy on the basal plane is almost within experimental error. Fig. 3 shows slip lines around the Knoop indentations on the basal plane. The slip traces are in directions of the type (1130). The presence of slip steps on the basal plane indicates that the slip direction lies out of the (0001) plane. Because WC has a c/a ratio of 0.976,' the shortest slip vector is [0001], which suggests slip systems of the type [0001] (1010). Fig. 4 shows slip lines around the Knoop intentations on the (1010) plane. These slip lines are inconsistent with [0001] slip but can be

Jan 1, 1965

By Lee Hillard Meltzer, Ralph E. Davis

INTRODUCTION During the past few years emphasis has been placed upon methods of estimating the future expectancy of gas production from natural gas fields. Before technical methods were applied, the production expectancy over future years was based upon the knowledge of gas well behavior, learned through long experience and embedded in the "know-how" of men long in the gas producing business. It is doubtful that a technical study of future expectancy of a gas field or a group of fields was ever prepared for the preliminary planning of a natural gas pipe line system built prior to about five years ago. The decline in well production capacity was naturally recognized by all familiar with the business since its earliest beginnings more than 75 years ago. In 1953, the Bureau of Mines published Monograph Number 7, "Back-Pressure Data on Natural Gas Wells and Their Application to Production Practices," which gave to the industry the first technical analysis of the decline in production of individual gas wells. This method affords a means of estimating the future production in relation to decline in reservoir pressure. The demand for technical determination of expectancy of future gas productivity from fields or a group of fields led technical men to the application of the knowledge of well behavior to the problems. The decline in a well's ability to produce as pressures declined could be estimated by the use of the curve known as the "back-pressure potential curve" as developed by the Bureau of Mines. A field containing few, or even numerous, wells could be analyzed on the basis of the sum of potentials of all wells. In most studies of this nature, the problem is to estimate the rate of production that can be expected, not only from present wells but also, from wells that will in the future have to be drilled into the reservoir being studied. The "back-pressure potential" method requires that the following data be known or estimated: (1) Proved gas reserves. (2) Current shut-in pressures and rate at which shut-in pressures change with production. (3) Back pressure potential data on wells in the source of supply. (4) Ultimate number of wells which will supply gas, and their potential. (5) Limitations on productivity such as line pressures against which the wells will produce, friction drop in the producing string, and so forth. It is evident that the resulting estimate of gas available in each year for a future of say, 20 years, contains many uncertainties. While the method may have considerable merit for a field that is fully developed, it cannot be completely dependable in fields that are only partially developed. In such cases, some of the data upon which it is based can only be estimated or assumed. In the study of this problem during the past few years, a method has been developed which we believe has great merit, especially when applied to fields subject to substantial future drilling, and when applied to the study of fields which, on the average, appear to have characteristics similar, in general, to the average of the fields used in the development of the "yardstick" outlined herein. From an analysis of the production history of 49 reservoirs which are depleted, or nearly depleted, a curve has been constructed which shows the average performance of the reservoirs during the declining stages of production. When properly applied, this "average performance curve" can be used to determine the stage of depletion at which a reservoir or group of reservoirs will no longer be able to yield a given percentage of the original reserves. "AVAILABILITY" AND "AVAILABILITY STUDIES" The rate at which. a reservoir will yield its gas depends basically upon physical factors, such as the thickness and permeability of the sand, the effect of water drive, if any, and other conditions, and upon economic factors, such as the number of wells drilled. Within the ranges set by the physical conditions, a rate of delivery tends finally to become established. The rate (or range of rates) represents a balance between the interests of the operator, who desires the maximum return from his property and of the pipe line owner, who desires to maintain a firm supply for his market. This balance, which is influenced by the terms of the contract, determines the capacity which will be developed by the operator, and the time and rate at which the decline in production is permitted to occur. Thus the "availability" of gas

Jan 1, 1953

By Oliver Bowles

ALTHOUGH Oliver Bowles retired as chief of the nonmetal economics division of the Bureau of Mines last year, that retirement has not lessened his active interest in the field of nonmetallic minerals, in writing, nor in his hobby, cultivation of African violets. Excellent co-ordination of the timing of a professional meeting and a flower show permitted him on at least one occasion to attend technical sessions and take in the African violet exhibition which happily arrived simultaneously in one city. Dr. Bowles celebrated his seventieth birthday on Jan. 10, 1947, and

Jan 1, 1948

By F. G. Jones, R. D. Pehlke, H. E. Gardner

The solubility of nitrogen in liquid Fe-18 pct Cr-8 pct Ni-0. 7 to 2.3 pct A1 alloys has been measured up to the solubility limit for the formation of aluminum nitride in the temperature range 1600° to 1700°C uszng the Sieverts' method. The solubility of nitrogen in 18-8 stainless steel increases with increasing aluminum content. Based on a nitride composition, AlN, the standard free energy of formation of aluminum nitride from the elements dissolved in liquid 18-8 stainless-steel alloys has been determined to be: ?G° = -42,500 + 20. IT in the range from 1600° to 1700° C. EVANS and pehlke1 have measured the equilibrium conditions for the formation of aluminum nitride, AlN, in liquid Fe-A1 alloys. The present study extends that work to the more complex solvent, liquid 18 pct Cr-8 pct Ni (18-8) stainless steel. Recent work by Small and pehlke2 has dealt with the effect of fourth-element additions on the solubility of nitrogen in 18-8 base alloys. They found the effect of aluminum additions, up to 0.74 pct, on the solubility of nitrogen to be small. The present study covered the range from 0.74 to 2.28 pct aluminum, and by extending the composition range may be used to better define the effect of aluminum on the nitrogen solubility in these alloys. EXPERIMENTAL PROCEDURE The Sieverts' method was used to measure the equilibrium solubility of nitrogen gas in liquid 18-8 stainless steel alloys containing 0.74, 1.49, 1.93, and 2.28 pct Al. The solubility was measured as a function of the nitrogen gas pressure at temperatures of 1600°, 1650°, and 1700°C. The apparatus used is the same as described by Small and Pehlke.2 The 100-g melts were made from Ferrovac-E high-purity iron, Crucible Steel Co.; 99.95 pct Cr, Union Carbide Corp.; 99.9 pct Ni, International Nickel Co.; and 99.99+ pct Al, Aluminum Co. of America. The aluminum was charged at the bottom of the crucible, surrounded by nickel and iron. The chromium was packed into the interstices to minimize vapor transport of the aluminum during initial melting. The hot volume of the system, measured for each melt with argon, ranged from 45 to 55 standard cu cm with a temperature coefficient of —8 x 10-3 cu cm per °C. The melt temperature was measured with a Leeds and Northrup disappearing-filament type optical pyrometer sighted vertically downward on the center of the melt surface. The temperature calibration of the system by Small and pehlke2 was assumed. Two problems are involved in determining the solubility product of a solid, metal nitride phase in liquid iron alloys. These are: 1) establishing the point of departure from Henrian behavior at the solubility limit of the metal nitride phase; and 2) determining the composition of the solid nitride which is precipitated. Determination of the solubility product of AlN was made by admitting small amounts of nitrogen into the reaction bulb until the deviation from Sieverts' law was clearly evident in the form of a pressure halt. To obtain the solubility product at several temperatures during one run the following procedure was used: 1) add increments of nitrogen to determine the Sieverts' law line at the lowest desired temperature; 2) continue to add nitrogen to precipitate a small amount of the nitride phase; 3) increase the melt temperature 50°C to dissolve the precipitated nitride; 4) repeat step 2 until either a nitride formed or the system reached ambient pressure; if a nitride formed at 1650°C, the sequence was repeated at 1700°C. The composition of the precipitated phase was checked by an X-ray diffraction pattern obtained from powder scraped from the surface of the solidified 1.93 pct A1 melt. RESULTS AND DISCUSSlON Solubility Measurements. Fig. 1 is a typical nitrogen-absorption curve obtained from measurements on a 1.93 pct A1 alloy. Since the initial absorption of nitrogen follows Sieverts' law the nitrogen solubility is plotted as a function of the square root of the pressure of nitrogen gas in the reaction bulb. The results of the solubility measurements for all alloys studied are summarized in Table I. The slope of the Sieverts' law line for each alloy was determined. Since this is also the solubility of nitrogen at 1 atm pressure of nitrogen gas, the latter designation is used for the data. It should be noted. however, that in most cases the value lies above the solubility limit for AlN. Fig. 2 shows the effect of aluminum on the solubility of nitrogen at this reference pressure and as a function of melt temperature. The solid portions of the lines represent attainable solutions; the dashed regions lie above the limit for precipitation of AlN.

Jan 1, 1969

By R. A. Oriani

The partial molal volume of hydrogen is one of the parameters that describe the elastic interaction between the solute and the stress fields about inclusions, dislocations, and cracks. As such the partial molal volume is probably of importance in the elucidation of phenomena such as hydrogen embrittlement and hydrogen yield point. A knowledge of this quantity would also be helpful in thinking about the state of dissolved hydrogen in iron. However, because of the very low lattice solubility of hydrogen in iron the usual ways of determining the lattice expansion are not practicable. It is therefore of interest to apply the thermodynamics of stressed bodies to two sets of measurements of the effect of elastic stress upon the permeability of hydrogen in order to deduce a value of the partial molal volume, VH, of hydrogen dissolved in a iron. Beck ..' and previously de Kazinczy, observed that a uniaxial tensile stress increases the permeability of hydrogen in iron and in various steels. Beck et 01. employed Armco iron and A.I.S.I. 4340 steel, whereas de Kazinczy used a steel the composition of which was 0.13 C, 0.23 Si, 0.46 Mn, 0.006 P, and 0.038 S. Upon releasing the stress the permeability increment disappeared if the stress was below the elastic limit. Both investigators employed cathodic charging to introduce the hydrogen. de Kazinczy measured the permeation through a thin-walled tube by collecting the gas, whereas Beck et al. measured the permeation through sheets of various thicknesses by a very sensitive electrochemical technique. Both investigators measured the steady-state permeation at constant rate of hydrogen ion discharge, and Beck measured in addition the hydrogen diffusivity by a time-lag technique which is independent of the boundary conditions. Beck et al. and de Kazinczy found a linear relationship between log (J,/Jo) and the stress, where Ju/Jo is the ratio of the flux of hydrogen when the metal is under uniaxial tensile stress, a, to the flux under zero stress, for the same temperature and charging current. Beck et al. found in addition that the diffusivity of hydrogen is not changed by stress. Both investigators concluded that the observed change in permeability is due to an increase in hydrogen concentration, and furthermore that the increase in concentration is due directly to the thermodynamic effect of stress upon concentration. Accepting this assessment of the situation for reasons given below, one may use the equation3j4 in order to evaluate I/H, the partial molal volume of hydrogen. This equation is valid for the domain of a/E «¦ 1 (where E is the Young's modulus) and under the assumption that hydrogen expands the lattice isotrop-ically. From the data of Beck el al, one calculates V7H - 2.0 cu cm per g-atom, and from those of de Kazinczy one obtains 1.8 cu cm per g-atom. That the increase of concentration with stress is indeed of thermodynamic origin is attested to by the facts that the experimental results conform to the thermodynamic relation, Eq. [I], and that the results are the same whether a pure iron1 or each of two different steels172 is used. Neither of these facts wou1.d necessarily be expected if the effect of stress were, rather, to increase the ratio kn/k, of the kinetic factors of the following competing reactions: H(ads) — H (dissolved) Such a change of kinetics at the surface could be an alternative explanation of the effect of stress on the permeability. Although this writer does not deem this explanation to be the correct one for the reasons given above, it must be admitted that unambiguous proof that the phenomenon has a thermodynamic origin does not yet exist. Two kinds of experiments may be suggested. One is to plate a variety of metals on the input surface of the steel and repeat the stress experiment at a variety of hydrogen charging currents. The other is to employ somewhat thicker specimens in order to be able to apply uniaxial compressive stress. Eq. [I] shows that ln(c,/c,) depends on the sign of the stress, but it is difficult to see a physical basis for which k2/kl would depend on the sign of a. The present value of V^ in a iron agrees with phragmen's5 estimate, which he based on comparisons with the lattice expansion by hydrogen of titanium, zir-

Jan 1, 1967

By J. S. Levine, M. Prats

A homogeneous and uniform cylindrical reservoir containing oil and gas is fractured vertically on completion and is produced at a constant bottom-hole pressure. The fracture has an infinite flow capacity, is of limited lateral extent and is bounded above and below by the impermeable strata defining the vertical extent of the reservoir. Results show that such a fractured reservoir can be represented by a reservoir of circular symmetry having very nearly the same production history. The well radius of this circular reservoir is about 1/4 the fracture length and is essentially the same as that obtained previously for a single fluid of constant compressibility. At the same value of cumulative oil production, gas-oil ratios of fractured reservoirs producing at constant terzinal pressure are larger than those of reservoirs having no fractures. This leads to more inefficient use of the reservoir energy in fractured wells and results in lower reservoir pressures for the same cumulative oil production. The reduction in operating life due to fracturing a reservoir is not as great as that for a slightly compressible fluid. This diflerence can be accounted for by the lower reservoir pressure in the fractured reservoir and its adverse effect on the average mobility and compressibility of the oil. As anticipated, the reduction in operating life increases czs the reservoir permeability decreases. The type of results presented in this report can be used to determine the economic attractiveness of fracture treatments per se, to setect the initial spacing to be used in developing a field, and to compare the relative merits of fracturing available wells and infill drilling. INTRODUCTION The effect of vertical fractures on a reservoir producing either an incompressible or a compressible liquid has already been discussed in the 1iterature.l,2 Those results indicate that the production history of such a reservoir is essentially the same as that of a circular reservoir having an effective well radius of approximately one-fourth the fracture length. The present work reports on the effect of a vertical fracture on a reservoir producing two compressible fluids —oil and gas—by solution gas drive. Because of the empirical nature of the PVT and relative permeability data used to obtain the performance of such reservoirs, results can only be obtained numerically and with the aid of high-speed computers. Since reservoirs lose their radial symmetry when fractured vertically, pressure and saturation can no longer be given only in terms of distance from the well. Two coordinates (such as x and y) must now be used to describe the pressure and saturation within the reservoir, and, since we are dealing with compressible fluids, time is also a variable. Thus the solution of a vertically fractured reservoir requires finding two unknowns (pressure and saturation) in two space variables (say x and y) and in time (t). Since no means are readily and generally available for solving such problems at the present time, we have used the results of previous work1,2 to approximate the effect of a vertical fracture on a reservoir producing both oil and gas by depletion. The purpose of the present wmk, then, is to investigate the possibility of using available numerical techniques (limited at the moment to one space variable) to study the two-space-variable flow behavior resulting from a vertical fracture. Results obtained in the course of this investigation are also reported and discussed. Input and output data of the numerical methods used are given in practical units: BOPD, feet, psi, cp, and md. Results are discussed fist in terms of specific reservoir and crude properties and geometries. Later, dimensionless parameters are introduced in order to extend results to different values of some of the reservoir and fracture properties. IDEALIZATION AND DESCRIPTION OF THE FRACTURED SYSTEM It is assumed that a horizontal oil-producing layer of constant thickness and of uniform porosity and permeability is bounded above and below by impermeable strata. The reservoir has an impermeable, circular, cylindrical outer boundary of radius r,. The fracture system is represented by a single, plane, vertical fracture of limited radial extent, bounded by the impermeable matrix above and below' the producing layer (reservoir). It is assumed that there is no pressure drop in the fracture due to fluid flow. 1 indicates the general three-dimensional geometry of the fractured reservoir. Gravity effects and the effects of differential depletion resulting from variations in hydrostatic head (pressure) will be neglected. Thus, the flow behavior in the fractured reservoir is described by the