Search Documents

By Paul Bechtner

THE name bentonite formerly was applied solely to a peculiar clay occurring in Wyoming and South Dakota, which was distinguished from other clays by its unctuous feel when wet and the property of swelling in water. In the last decade scientific studies of clay have recognized that bentonite is composed mainly of the clay mineral montmorillonite and the name bentonite has been extended to cover the entire family of clays that have montmorillonite as their chief constituent. Montmorillonite has the chemical formula of A1203-4Si0-xH2O, With Fe203 and MgO replacing part of the A1203. The montmorillonite crystal is an Si-Al-Si clay mineral, being formed of two silicon-oxygen sheets with an aluminum-oxygen sheet sandwiched between them. In contrast, kaolinite-the chief clay mineral of most clays other than bentonite-is Si-Al, one silica and one alumina sheet. The unit crystal of montmorillonite is much thinner than that of kaolinite, with greater surface area. These differences in crystal structure patterns are leading factors in the dissimilar properties and commercial uses of bentonite compared with other clays. Mineralogically, bentonites are 85 to 90 pct montmorillonite with fragments of feldspar, gypsum, calcium carbonate, quartz and traces of other minerals. They vary in color; the widely used Wyoming type is creamy white when dry and a light shade of tan when wet; the low-swelling bentonites of the southern United States and elsewhere are found in many shades of gray, blue, yellow, red, and brown. Pure white bentonites are rarer and generally of the medium or low-swelling type, though there are a few exceptions to that general rule. PROPERTIES Bentonites may be divided into two general classes: (1) those that adsorb large quantities of water, "swelling" greatly in the process, and that remain in suspension in thin water dispersions; (2) those that adsorb only slightly more water than ordinary plastic clays or fuller's earths, do not swell noticeably, and settle rapidly in thin water dispersions. Another distinction is that some varieties of the No. 2 type

Jan 1, 1949

By D. C. Hilty, W. Crafts

J. Chipman—It has been my privilege to discuss this work with the authors on several occasions and to observe at first hand the experimental methods employed. I wish, therefore, to emphasize certain points which they have mentioned only briefly with regard to the experimental techniques. The rotating induction furnace as here employed interposes liquid metal between slag and refractory thus preventing the two nonmetallic parts of the system from reaching equilibrium with one another. It is therefore impossible for the metallic phase to be completely in equilibrium with both the slag and the crucible. The metal also acts as a partially permeable membrane allowing certain components, including oxygen, to diffuse from slag to crucible. This transfer results in building up on the face of the crucible a layer of material whose composition is in part dependent on that of the bath. Reactions between the layer and the solid refractory are slow, as evidenced by the rather good life of the crucible. Hence it seems probable that the layer is more nearly in equilibrium with the metal than with the underlying crucible material and that, once it is established under a bath of a given composition, its further reactions with that bath are slow. Additions to slag or bath may be followed by changes in the layer; and time must be allowed for virtual completion of such changes, before it can be assumed that slag and metal are in equilibrium. We may judge from the results reported that, in general, this was the case and that the data represent at least quite close approximations to slag-metal equilibrium. Data on deoxidation and on oxygen solubility are no better than the analytical methods employed. The vacuum fusion method as used by the authors seems entirely adequate for the samples analyzed. I have had frequent occasion to compare results with their laboratory, always with very satisfactory agreement. The determination of aluminum at very low concentrations is perhaps an even more difficult procedure. Here also the colorimetric method used has been worked out with great care and is undoubtedly the most dependable method available. The discrepancy between observed and calculated deoxidation or solubility lines is not to be explained as the result of experimental errors, either in the sampling or analysis of the metal. Nor is it to be blamed upon inaccuracies in the several kinds of indirect data upon which the calculated results were based. It is true that both the observed and the calculated lines admit of some uncertainty as to their exact locations, but the uncertainties are small compared to the wide gap which separates the two lines. The authors have pointed out the real cause of the discrepancy. In all of their experiments the solid phase was not Al2O3 but a mixed oxide containing iron and aluminum. This suggests an extension of the calculated values to include equilibrium with the spinel FeO . A12O3. The free energies of FeO and A12O3 are known, that of the spinel is not. However, it cannot differ greatly from that of its component oxides for even in the more stable spinel, chromite, the free energy of formation from the oxides is less than 10,000 cal. For purposes of calculation we shall call this free energy X and solve for values of X lying between zero and 10,000 cal. The other data required are taken from the forthcoming revision of "Basic Open Hearth Steelmaking" and are given in the following equations in which underlined symbols indicate elements dissolved in liquid steel and the standard concentrations are 1 pct. ?F° at 1600°C, cal ?LA = 2 Al + 3 O; + 107,200 FeO = Fe + 0; + 5,460 FeO + A12O3 = Fe + 2A1 + 4 0; + 112,660 — X The corresponding equilibrium concentrations are shown in fig. 21. The line marked A12O3 corresponds to the first equation, those marked FeO . AL2O3 correspond to the last, with X = 0, 5000 and 10,000 cal, respectively. The two upper lines represent the data of Hilty and Crafts and of Wentrup and Hieber. The points are the observations of Hilty and Crafts in the presence of 0.50 pct Mn.

Jan 1, 1951

By G. H. Kessler

ALTHOUGH considerable attention has been devoted to reaction mechanisms and equilibria of a number of endothermic reactions through which metals or their refractory compounds can be formed upon heated surfaces, only a comparatively small amount of work has been done to develop rate information for these systems. The interestin and very worthwhile work of Holden and Kopelman, Runnalls and Pidgeon,Dijring and Moliere, and Herrick and ICrieble4 is to be noted; however, their work was done under very specific conditions and the rate information which they have developed is not applicable to many systems which have been studied experimentally. That a more generalized approach is needed is shown by the diversity of these systems and of the experimental conditions which they require. These include the preparation of titanium, zirconium, tungsten, molybdenum, chromium, co-lumbium, aluminum, and silicon by decomposition or disproportionation of their halides, in some instances through hydrogen reduction; the preparation of nickel and iron by decomposition of their car-bonyls; and the preparation of copper by decomposition of the acetylacetonate. They may be carried out at temperatures ranging from 100" to over 2000°C and at pressures of from less than one mm Hg to superatmospheric. The physical mechanism of the overall process can be broken down into several steps, any one of which may be rate-determining; and the rate associated with each of these basic physical processes can be predicted. Consequently, by proper application of the present technology of rate processes, it is possible to arrive at a rate of metal deposition in the system of interest and to reach an understanding of the influence of' each major variable upon the deposition rate. It is the purpose of this paper to illustrate how this can be done and to present experimental results for a specific system for comparison with theory. The overall process of deposition of metal upon a heated surface which is immersed in vapors of a compound of the metal can be broken down into the following steps: 1) Transport of the reactant vapors to the surface. 2) Decomposition of the reactant in the immediate vicinity of the surface to a) establish chemical equilibrium if reaction rates are high; or to b) establish a dynamic equilibrium in accordance with the several reaction rates. 3) Diffusion of reaction products away from the vicinity of the surface, with or without simultaneous recombinations to form still other products. The overall process is said to be diffusion controlled if Step 1, or the equivalent Step 3, is slow; it is reaction-rate controlled if Step 2b is slow. When experimental evidence shows the reaction rate to be controlling, the well-known theories of Eyring' and others can be used as a basis for correlating and extrapolating the experimental data. Although these theories give only approximate estimates of reaction rates, they are of considerably greater value in correlating experimental data. Most deposition systems operate at surface temperatures sufficiently high that reaction rates near the surface are very high. Mass-transport rates then become controlling; and it is this regime of diffusion controlled rates which is most often of concern and Which will be considered here. When the system pressure is very low, i.e., in the micron range, then the transport processes are those of molecular movement, and the results of kinetic theory can be applied to specify a rate of arrival of reactant molecules at the heated surface. If the condensation coefficient can be estimated, then the deposition rate will be given by the product (rate of arrival) x (condensation coefficient), Conversely, experimental data can be used to determine a condensation coefficient, as was done by Holden and Kopelman' for the decomposition of zirconium tetraiodide upon a heated molybdenum surface, who found the coefficient for zirconium on molybdenum to be 1.0 at temperatures of 1382°C and above. In this pressure range, the geometry of the system. and in particular the distance between the source of reactant molecules and the heated surface, can exert a considerable effect upon the deposition rate;

Jan 1, 1961

By E. T. Hayes, A. H. Roberson, M. H. Davies

R. F. Dornagala and D. J. McPherson (Armour Research Foundation, Chicago)—I should like to compliment the authors for a workmanlike job in determining the partial phase diagram of a system comprised of two rnetals which are certainly not easy to work with. We are completing work at Armour Research Foundation on an Atomic Energy Commission-sponsored project for the determination of eight zirconium binary diagrams. Work on the Zr-Cr system has been completed and should be published within the next year. For our work, Westinghouse Grade 3 iodide crystal bar served as the zirconium melting stock. Johnson-Matthey, electrolytic chromium, specially treated for oxygen removal, was employed. The overall constitution of the system determined at Armour Research Foundation is in very good agreement with the present work. We found a eutectic at 18 pct Cr and 1280 °C, somewhat lower than the value reported. This temperature was confirmed by thermal analysis, incipient melting studies, and regular isothermal anneals. The eutectoid was located close to 1 pct Cr and 835°C by metallographic analysis of annealed specimens. Maximum solubility of chromium in /S zirconium was 4.5 pct at the eutectic temperature. Chromium solubility in a zirconium was less than 0.28 pct at all temperatures. We found the compound at 53 pct to melt around 1700°C, with an open maximum, but determined its crystal structure to be hexagonal close-packed (MgZn, type). The lattice parameters were in excellent agreement with those determined by Wallbaum in 1942. The diagrams are in substantial agreement, and .part of the differences are undoubtedly due to the use of different zirconium melting stock. M. K. McQuillan (Birmingham, England)—I read this paper with a great deal of interest, as it covered the same field as some work of my own.' There are a number of points in the present paper on which I would like to comment. First, I should say that I, too, used zirconium prepared by magnesium reduction of the tetrachloride and electrolytically prepared chromium, and melted the alloys in a Kroll-type arc furnace. The purity of my alloys should, therefore, be comparable with the purity of those of the present authors, and any differences in our observations would not be expected to be attributable to this cause. The differences between my observations and theirs concern the presence of the eutectic, the temperature of the eutectoid, and the melting point of the compound. I would be very much interested in any further evidence the authors may have for the occurrence of the eutectic at 1380°C. During the course of my work I noted that a number of my alloys containing 60 to 90 pct Zr melted at about 1400 °C, and for a time assumed that a eutectic occurred at this temperature as described in the paper. On further investigation, however, I found that the structures of the as-melted alloys could not be made to fit in with this interpretation of the system. If a eutectic exists in this region of the system it would be expected that the as-melted alloys would show the usual type of cast structure, i.e., dendrites of the compound plus eutectic. This, however, does not occur, as may be seen from Fig. 9. The compound seen there is not dendritic in form, and the remaining material is by no means certainly eutectic. It may be argued that a compound such as ZrCrl would not form dendrites but would tend to crystallize in geometric shapes. In this case, however, I have evidence to the contrary, as on the chromium side of the compound, where a eutectic occurs at about 1545"C, the compound formed from the liquid takes on a conventional dendritic form, and the eutectic is observed in the interdendritic spaces in the usual way. There is no reason to suppose that the compound would behave differently in an alloy lying on the zirconium side of the compound composition if a eutectic existed there too.

Jan 1, 1953

By G. W. Healy, L. F. Sander

was investigated by reacting thin discs of calcium oxide with gas mixtures of CO2, CO, and Son. Its value was 19,300 * 300 cal independent of temperature in this range. No solid solubility of sulfur in calcium oxide was detected within the limits of the experimental method and it is estimated to be below 0.025 pct by weight. The importance of lime in desulfurization is well-established but complete information on the pure phase equilibrium: CaO + 1/2 s2 = CaS + +02 [11 is not yet available. The goal of this work was to evaluate solid solubility of CaS in CaO and to determine the free-energy change associated with Reaction [I] at temperatures of 1400" to 1650°C. The equilibrium constant for Reaction [1] can be written: It is convenient to rewrite Eq. [2] in the form: where A = {Ps /PqJ1'2 has been referred to' as the "sulfurizing power' of a gas mixture. In this work, thin discs of CaO were suspended in a vertical tube furnace and exposed to CO + CO2 + SOz gas mixtures having known values of A. The samples were then analyzed for sulfur. As expected, X-ray diffraction confirmed that CaS was the only sulfur-bearing phase formed at the relatively low oxygen pressures used. EXPERIMENTAL PROCEDURE Reagent-grade CaCO3 was pressed in a 3/8-in.-diam pill die and prefired in air to produce CaO discs weighing between 0.004 and 0.01 g. Several discs were used to provide a suitable weight for chemical analysis while maintaining a large surface area to react with gas mixtures. These were placed in a platinum mesh basket and suspended in the gas stream in the hot zone of a vertical tube furnace. Desired gas mixtures were prepared from cp grade CO and CO2 and anhydrous grade SO2. The method of soap bubble displacement was used to calibrate capillary flow meters. While this gave excellent results with CO and Con, some problems with bubble insta- bility and soap film "drag" arose with the use of SO2 at low flow rates. Hence, frequent sampling and analysis of gas mixtures was carried out to insure proper control of the ingoing SOZ. The furnace used for gas:solid equilibration was a vertical mullite tube externally wound with 60 pct Pt-40 pct Rh wire having a diameter of 0.028 in. An inner tube of $ in. ID served as the reaction chamber having Pyrex ground joints sealed to the mullite to provide gas-tight connections at top and bottom. A Pt-Pt 10 pct Rh thermocouple was inserted into a protection tube adjacent to the sample basket to measure sample temperature during a run. Constant-temperature control to 2C was observed at any desired set point within the range of this investigation. This was accomplished by a control thermocouple imbedded in the furnace windings which served to actuate an electronic controller wired for high-low operation. The sulfur analyses of the solid samples were carried out using a stoichiometric combustion technique based on the method of Fincham and Richardson. Some analyses were done using a modified evolution method3 but these were used primarily to check the results of the combustion method. The results were in good agreement but the combustion technique of-ferred an advantage in economy of time and material. CALCULATION OF GAS EQUILIBRIA Heating a given mixture of CO + CO + SO2 to high temperatures gives rise to a large number of product species. The details of calculating the partial pressures of these products of interaction and dissociation can be found in several references4,5 and need not be repeated here. The thermodynamic data selected for the major species in the gas mixtures are shown in Table I. Equilibrium constants from these reactions were combined with oxygen, carbon, and sulfur balances and a computer program written to facilitate the calculations. Some early difficulties in reproducing experimental results were finally traced to the effect of atmospheric pressure changes. No reference to consideration of this question had been found in the

Jan 1, 1969

By John Tabor, R. B. Spivey

INTRODUCTION Shafts have been sunk in a number of ways. By and large, however, most have been sunk by drill, blast, muck, and slip form methods. Most methods have provided satisfactory means of completion. The major drawbacks to the conventional methods have been: (1) un- reliable cost estimates for completion; (2) unreliable rates of progress; and (3) unreliable integrity of the shaft lining. Recently , engineering design studies have been done that strongly indicate, that, by the use of existing proven technology, shafts can be completed faster, more cheaply, safer, and with a better lining that has been possible using conventional methods. THE METHOD The alternate method utilizes the techniques of big hole drilling, shield excavator tunnelling, and pre-cast concrete lining. Big Hole Drilling - Drilled shafts have been completed for several years and I don't intend to address the technology, only to point out the use of drilled shafts is an alternate method of shaft sinking. Ideally, in a multi-shaft mine, the first shaft would be blind bored and cased to a size, whereby it can handle the muck from the excavation of subsequent shafts. It should be an 8' to 10' completed diameter. The cost of such a shaft in sedimentary formations compares favorably with a conventional shaft. However, it is much faster. For additional shafts, the role of the drill is to complete small holes (3' to 4') to the desired horizon. This is merely a hole to allow slashing to a larger size with easier muck removal from an underground drift connected to the previously drilled shaft. The smaller holes, just as the larger one, should be cased and grouted into place so as to assure a smooth open hole. SHIELD EXCAVATOR Theory and History - Tunnelling Shields have been in common use for several decades, and steam powered shields were used in England over 100 years ago. The purpose of the shield is to provide temporary ground support, protect personnel during operation, and to house the excavating equipment. The excavating equipment approach has varied from attempts at a continuous or semi-continuous boring machine, the tunnel mole, to a mechanical or hydraulic digging arm. The shield may or may not be an active digging element. If not active, the boring tool or cutter is advanced ahead of the shield to full diameter and then the shield is moved up to the cutter, or the shield advances along with the cutter. If active, the cutter opens a conical free face, and the shield is either jacked forward so that the leading edge spalls rock to the free face or poling plates are thrust forward to spall to the free face. In either approach, various methods of muck removal are incorporated into the shield. These may be gathering arms, conveyors, or with moles, hydraulic transport, where the cuttings are sufficiently fine. The efficiency of the muck removal system is critical as excavation is rapid and the system could easily become muck-bound. Application to Shaft Sinking- Technically, the use of a shield to sink vertical shafts is no different than a tunnelling operation. It is, in fact, less complex in most respects. Muck and water removal are difficult in a blind-driven shaft. However, where an underground opening is available for handling muck and water, rapid shield sinking is possible, using a pilot hole for muck and water to fall through and be removed from below. The Tabor Mining Shield is basically a caisson approach, whereby, the ground is only seen at the face or bottom. It does have hydraulic jacks to force it downward and has segmented cutting edges which allows forepoling ahead of the shield. The hydraulic excavator allows mining in the center of the face around the previously drilled hole with the forepoling segments slabbing to this free face. First, the drilled hole is cased and grouted. The machine is a tube with an excavator. The work cycle is as follows: (1) The casing and grout are cut at predetermined intervals by shaped charges. (2) The casing is crushed by the excavator, removed from the hole and hoisted to the surface. (3) The excavator then rips out a face around the hole by digging the formation in tension and breaking the pieces

Jan 1, 1982

By B. S. Gottfried

A generalized mathematical model is presented, which describes the thermal recovery of oil in linear systems with convective external heat loss. Three-phase fluid flow, conduction-convection heat transfer, chemical reaction between oxygen and oil and aqueous phase change are included, making the model applicable to a variety of thermal recovery processes. The complexity of the model requires that numerical solutions be obtained with a digital computer. The numerical approximations of the partial differential equations are presented and the algorithm is discussed in detail. The analysis is applied to the detailed simulation of a forward-combustion laboratory tube experiment. The results of the simulation exhibit with reasonable accuracy all of the principal thermal and bydrodynamic characteristics observed in the laboratory (i.e., the propagation of a combustion zone, a steam plateau, and oil and water banks). Numerical variations in the parameters appearing in the external heat-loss term, the aqueous phase-change term, and the Arrhenius combustion term are examined, and their effects on the predicted temperature profiles, oil and water production histories, and the air-oil ratio are presented. In spite of an oversimplification in the chemical reaction mechanism and the considerable computer time required to obtain solutions, the model represents a major advance in the ability to simulate the phenomena observed in thermal recovery experiments. INTRODUCTION Thermal oil recovery refers to a class of recovery processes where heat is supplied to a reservoir to provide the necessary expulsive energy. This thermal energy can be supplied externally as steam or hot water, or it can be generated in situ by forward or reverse combustion. In either case, however, thermal recovery processes are charac- terized by the simultaneous flow of two or three fluid phases in a variable - temperature field, accompanied by possible chemical reaction or phase-change effects.2-5, 7- 10, 14,16-18,20-22 Although a physical understanding of the thermal recovery processes is far from complete, it is possible to construct mathematical models which describe approximately all of the principal physical and chemical phenomena. However, attempts to solve such models, even with high-speed computers, involve formidable mathematical difficulties. Consequently, theoretical solutions have been obtained only for idealized cases in which important physical phenomena are neglected. For example, consider the process of forward in situ combustion. All such theories which have been developed consider only certain aspects of the process, such as heat transfer, 2-4,8,9,l6,l8 heat transfer with phase change,10 heat transfer with chemical reaction,7 or the hydrodynamics of three-phase flow.21 A general theory including all of the above phenomena has not been developed to date. This paper presents a unified theory of thermal recovery processes in linear systems. A mathematical model is developed which explicitly includes conduction-convection heat transfer with convective external heat loss, chemical reaction between air and oil, aqueous phase change, and the hydrodynamics of three-phase flow. A system of equations is developed which can be solved numerically on a high-speed digital computer, resulting in predicted temperature, pressure, and saturation histories in space and time. The model allows a more detailed simulation of thermal recovery tube experiments than had previously been possible. THEORETICAL DEVELOPMENT Consider the linear flow of gas, water and oil in a homogeneous porous medium. Assume that the oil will react with gaseous oxygen, and that mass is transferred between the water and gas phase by evaporation or condensation. In the absence of hydrocarbon phase change, intraphase diffusion,

Jan 1, 1966

By A. Steiner, E. Miller, K. L. Komarek

Equations have been derived to calculate the chemical potentials of the components of liquid binary alloys from liquidus and enthalpy data. The equations are applicable to systems with intermetal-lic compounds of limited solid solubility. The liquidus curve of the Mg-Sn system was accurately redetermined, and the melting point of the compound Mg2Sn was found to be 770.5° * 0.3°C. The thermo-dynamic properties of the liquid alloys were calcu -lated from the liquidus data. The activity of tin shows both positive and negative deviations from Raoult&apos;s law and the relative integral entropy is positive. THE phase boundaries in an equilibrium phase diagram are functions of the thermodynamic properties of the coexisting phases. Specifically, the shape of the liquidus curve near an intermediate compound is determined by the properties of the compound and the liquid phase. Hauffe and wagnerl have derived an equation for the chemical potential differences (ui) of the liquid alloys near the congruent melting point when the heat of fusion of the compound and the liquidus curve are known. In their derivation the temperature dependence of the ui value was neglected, and liquid of stoichio-metric composition was chosen as the reference state. To obtain chemical potentials over the ntire composition range of the phase diagram with the pure components as the reference state, equations have been derived which incorporate the temperature dependence of the chemical potentials. Such a thermodynamic analysis can be carried out when the liquidus curve and the enthalpy values are known. The equations have been applied to the redetermined liquidus curve of the Mg-Sn system to obtain the thermodynamic properties of liquid Mg-Sn alloys. The Mg-Sn phase diagram has been studied by various investigators and the results have been compiled and critically assessed by Hansen.2 Preliminary thermal analyses showed that the basic features of the diagram were correct. The system has one congruent melting compound, Mg2Sn, two eutectics, and some solid solubility of tin in magnesium. However, the published liquidus temperatures show considerable scatter. In order to perform an accurate thermodynamic analysis, the liquidus curve between the magnesium-rich and tin-rich eutectic compositions was therefore redetermined by careful thermal analysis using highest-purity starting materials. EXPERIMENTAL PROCEDURE The magnesium metal (Dominion Magnesium Ltd, Toronto, Canada) had a purity of 99.99+ pct with the following impurities (in ppm): 20 Al, 30 Zn, 10 Si, <1 Ni, <1 Cu, <10 Fe; tin (Cominco Products, Spokane, Wash.) contained 99.999+ pct Sn. The graphite crucibles were machined from graphite rods (United Carbon Products Corp., Bay City, Mich.) which had an average total ash content of less than 30 ppm. All the graphite parts were baked out in vacuum at 950" to 1000°C for a minimum of 24 hr to remove volatile organic materials. The graphite crucibles (3 in. long, 1-5/8 in. OD, 1-3/8 in. ID) were tightly closed with a threaded cover (1/2 in. thick) which had a central thermocouple well (2-1/4 in. long, 5/16 in. OD, 3/16 in. ID). Cover and thermocouple well were machined from one piece of graphite. A thin sheath of quartz was inserted in the well to protect the thermocouple

Jan 1, 1964

By R. G. Davies, R. H. Richman

Several techniques, X-ray diffraction, transmission electron microscopy, conventional, metallography, and mechanical property measurements are combined to investigate decomposition in the suPersaturated solid solution Fe-27 at. pct Be. The following sequence of structures for aging temperatures below 400°C is established: massive short-range order, pseudo-FeBe (L2o) order, Fe3Be (DU3) order, sinusoidal modulation of composition, general or continuous precipitation, and discontinuous or cellular precipitation. In addition to this sequence itself, several features of the individual stages are noteworthy; for example, when coherent modulations occur, their development is parallel to (100) everywhere in the specimen apparently without incubation, and both the wavelength and the composition amplitude of the modulations increase with aging time. Two types of discontinuous reaction are observed, depending upon the aging temperature. At low temperatures (<550°C) the boundary-nucleated variety of discontinuous precipitate predominates; but at higher temperatures (>600°C) the crystallographic variety occurs instead. Hardness and flow-stress measurements clearly reflect the quoted structure sequence. Some qualitative aspects of the structure changes and of the relationship between mechanical properties and structure are discussed. BERYLLIUM in solid solution markedly strengthens iron.&apos;" A recent study demonstrated that not only were supersaturated single crystals of Fe-27 at. pct Be very strong, but they deformed primarily by mechanical twinning.3 Such behavior, coupled with the decrease in solid solubility of beryllium in a Fe from about 33 at. pct at 1165°C to about 10 at. pct at 500°C4 as shown in Fig. 1, leads naturally to questions about property changes with aging in this system. In 1929 roll,1 and later Seljesater and Rogers,5 reported that useful increases in strength could be obtained by aging quenched Fe-Be alloys, but it was not until quite recently that any of the details of precipitation in these alloys were studied. Richman6 observed that both an Fe3Be superlattice (with a DO3 crystal structure the same as Fe3A1, illustrated in Fig. 2) and a modulated structure preceded the appearance of a discrete second phase in the 20 at. pct Be composition. Here, a modulated structure refers to a periodic composition fluctuation within one crystal, while its lattice remains coherent. Subsequent work on a Fe-Be alloys by Heubner7 and von Heimendahl and Heubner8 confirmed the existence of the modulated structure, although only an FeBe (L20) ordered structure was detected (also shown in Fig. 2). Both Rich-man and Heubner corroborated the large increases in hardness during aging reported earlier, but other mechanical properties were not examined. Since modulated systems are encountered relatively infrequently, the influence of coherent modulation upon mechanical properties is not well-known. With the accumulation of information about age-hardening systems, it has become clear that many precipitation reactions cannot always be described by the concept of heterogeneous nucleation at some lattice discontinuity followed by diffusional growth. Rather, complex sequences involving prior "preparation" of the matrix are quite common; that is, a transition structure occurs in the parent phase, instead of in some "nucleus" form. Delineation of such subtle sequences appears to be a worthwhile step toward the understanding of solid-state precipitation. Since not many structural progressions of comparable nature have been reported, the objectives of the present survey are to identify and elucidate the various

Jan 1, 1967

By R. E. Miner, J. K. Jackson, D. F. Gibbons

Internal-friction measurements were made during isothermal aging treatments of 18 pct Ni maraging-steel wires between 420° and 612°C. A sharp initial drop in the internal-friction level was interpreted in terms of a rapid dislocation recovery reaction. The rate of the recovery was found to be independent of temperature. Truncation of the recovery reaction was apparent in those systems that exhibited the rapid age-hardening characteristics of the maraging steels. It is proposed that this initial hardening response is the result of a low activation energy preprecipitation reaction involving molybdenum. A gradual rise in the internal-friction level at longer aging times was associated with the precipitation of a molybdenum-containing precipitate. CONSIDERABLE research effort has recently been devoted to the mechanisms responsible for the high strength and toughness of 18 pct Ni maraging steels. These bcc martensitic alloys are found to harden during aging at temperatures between 400° and 600°C. The aging response is very rapid with more than half the total hardness increase occurring within the first few minutes of aging, Fig. 1. Precipitate particles have been observed in the later stages of aging by a number of investigators.&apos;-&apos; While the identity of the precipitates remains the subject of some controversy, one or more of the intermetallic compounds, Ni3Mo, Ni3Ti, and Fe2Mo, are almost certainly involved. Heterogeneous nucleation of precipitates at dislocations has been noted8 and cobalt is believed to enhance the formation of fine, homogeneously distributed particles by lowering the solubility of the alloying elements in the martensitic matrix.3,7 Transmission electron microscopy studies of the initial hardening behavior have not been fruitful. Strengthening mechanisms based on atomic ordering have not been generally supported by X-ray and neutron-diffraction experiments.9 In the present investigation, the aging reaction was studied using isothermal-aging internal-friction measurements. The marked sensitivity of internal friction to short-range diffusion and precipitation processes has provided a convenient tool for the elucidation of the strengthening mechanisms operative in the maraging steels. EXPERIMENTAL PROCEDURE An upright torsion pendulum was used to measure the internal friction of several maraging steels during isothermal aging. The pendulum was placed in an atmosphere of helium at a pressure slightly less than atmospheric. To permit measurement of internal friction during the first minutes of aging, the specimens were rapidly heated by passing a current through them in a manner similar to that described by Ang and Wert.10 Thermal gradients in the specimen were largely eliminated by using specially designed specimen grips11 which produced temperature variations of less than 1 pct over 90 pct of the specimen length and less than 3 pct over the entire length at aging temperatures up to 620°C. A proportioning strip-chart program controller was employed to maintain constant specimen temperature during treatments of up to 36 hr duration. A number of vacuum-melted laboratory heats having compositions near that of a typical commercial 18Ni-7Co-5Mo-0.4Ti alloy were investigated. The amount of cobalt was varied from 0 to 7 wt pct in five of the heats. Either molybdenum or titanium was omitted in the remaining two heats. The alloy desig-

Jan 1, 1967

By Fritz Wald, Martin Weinstein, Herbert E. Bates

ONE of the methods for preparing a fiber-reinforced composite is that of directional solidification of a eutectic melt. Its major drawback lies in the fact that the matrix in this case is a pure constituent (or a terminal solid solution of fixed concentration) and the ratio of fiber to matrix volume is fixed. Only very few, if any, pure metal matrices possess technically useful properties, and the necessity for alloying is the inevitable consequence of this fact. Nevertheless, structures similar to binary eutectic ones can be obtained in higher-order systems by pseudoeutectic reactions of a type where crystallites and a solid-solution matrix are simultaneously precipitated from a liquid.1"3 Trials to solidify such alloys directionally—the matrix consisting of a solid solution of chromium, nickel, and silicon and the reinforcing phase being Cr3C2— will be reported elsewhere.4 This note describes constitutional studies carried out primarily to determine -the position of the pseudoeutectic and further to insure that no undesirable reactions between the reinforcing phase and components of the matrix occur in the solid state at elevated temperatures. In the investigation it was specifically desired to reinforce a matrix which is as close as possible to the 80/20 Nichrome composition with Cr3C2 to insure good oxidation resistance and improve the strength at high temperatures. No konstitutional information on the quaternary C-Cr-Ni-Si svstem in the range of interest was found in the literature. Nevertheless, the two most important ternaries c-cr-Ni5 and have been completely investigated. On C-Cr-Si some investigations have been conducted,7"9 and C-Ni-Si was studied with a few alloys in the course of the present investination 9 Eight alloys were prepared to investigate the changes in the constitution of the ternary C-Cr3Ce-yNi eutectic5 with silicon contents up to 10 wt pct. Five alloys were made with varying chromium and carbon contents around compositions containing -60 to 70 wt pct Ni and 5 to 6 wt pct Si. The latter alloys were designed to locate the y(Ni-Cr-Si-C)-Cr3C2 pseudoeutectic reaction and to determine the maximum chromium content in solid solution compatible with a two-phase equilibrium between y and Cr3C2 only. The alloys were prepared from electrolyte nickel, semiconductor-grade silicon, high-purity chromium (99.999 pct pellets), and semiconductor-grade graphite. They were melted inductively in high-purity alumina crucibles under flowing argon. Twenty-gram charges were prepared and investigated by optical microscopy (including hot-stage investigations), X-ray powder methods, and electronmicroprobe analysis. The alloys were studied in the as-cast condition and also after a homogenization annealing treatment of 48 days at 900°C in evacuated quartz ampoules. The structures of all alloys based on the ternary eutectic plus silicon in the as-cast state consisted generally of an inhomogeneous solid solution and at least two other phases. Annealing of the alloys showed that the solid solution was homogenized but that an incomplete solid-state reaction had taken place in all alloys with silicon contents over 5 wt pct. This reaction is clearly visible in Fig. 1 around the large Cr3C2 crystals (gray areas). Below this concentration, the alloys consisted of a homogeneous matrix and precipitates of Cr3C2 plus graphite, Fig. 2. The Cr3C2 was entirely unreacted here. From these observations and subsequent X-ray and microprobe investigations, it was deduced that the

Jan 1, 1969

By K. G. Kreider, J. H. Brophy, J. Wulff

The technology of nickel-activated sintering of tungsten powder has been successfully applied to the densification of plasma-sprayed tungsten. Nickel was added by infiltration in a zinc solution followed by evaporation of the solvent. After sintering one hour at 1300°C density 95 pct of theoretical and transverse rupture strength of 74,000 psi were obtained. Shrinkage was found to be anisotropic and the mechanism of densification was comparable to that found in the nickel-activated sintering of tungsten powder. 1 HE use of a plasma spray gun for the fabrication of massive tungsten parts has become increasingly interesting. Applications now exist where a deposit in the as-sprayed condition is satisfactory. However, these deposits are generally characterized by a lamellar anisotropic microstructure containing 15 pct porosity of which, typically, two-thirds is open to the surface. Mechanically, the as-sprayed deposits fail at relatively low stress levels with a biscuit-like fracture. As a result of these problems the possibility of improving structure and strength by sintering treatments subsequent to spraying is particularly attractive. Preferably this sintering treatment should be adaptable to large bodies of sprayed metal. The similarity between the as-sprayed tungsten structure and that of a powder compact suggests that the relatively low-temperature activated sintering technique1 might be profitably employed in the densification of plasma-sprayed tungsten. It was the purpose of the present investigation to develop a technique for introducing the nickel-activating agent into the sprayed structure, to evaluate the amount and mechanism of densification obtained as a function of time and temperature, and to obtain an indication of the relative strength before and after sintering. EXPERIMENTAL PROCEDURE Powder used for spraying was purchased from the Wah Chang Corp. in several size fractions ranging from an average size of 4 to 150 . These powders were sized further for an explicit study of the influence of average feed size on densification. All powders were dried at 200°C before use. Spraying was accomplished with a Plasma Flame unit manufactured by Thermal Dynamics Corp. Several modifications of the unit were helpful in conducting the investigation. A variable speed auger feed mechanism coupled with the carrier gas mecha nism facilitated the use of fine particle sizes. A coil of ten turns of copper tubing in series with the arc power and concentrically would around the nozzle improved nozzle life and extended the range of operating currents available. The function of the auxiliary coil was to cause the arc to spin and to prevent impingement at only one point in the nozzle. Normally air sprayed deposits were made with an arc maintained at 400 amp at 50 to 70 v. The arc was blown by a gas mixture containing from 5 pct H, 95 pct N for the finest powder feed sizes ranging to 20 pct H, 80 pct N for the coarsest size. The flow rate was maintained at 100 cu ft per hr NTP through a nozzle of 0.25 in. ID. When apraying in air, the powder stream was directed toward an aluminum substrate for ease of mechanical removal of the deposit. The substrate was cooled by diverting the plasma flame with an air jet, and a second jet was directed on the deposit surface. In this configuration a gun-to-work distance of 2 to 3 in. was found to be satisfactory. Fig. 1 represents a typical as-sprayed deposit micro-structure. Laboratory studies of protective atmosphere spraying were carried out in cylindrical chamber 8 in. in diam by 18 in. in length. In operating the nozzle attached to such a chamber, particular care was required to avoid nozzle burn out due to reduced gas flow. The structure and density of the chamber sprayed deposits varied over wide ranges depending on substrate temperature. For the purposes of this investigation, flat deposits were made approximately 2 in. sq by 3/8 in. thick. From these deposits individual samples were cut an ground to a rectangular shape typically 1 1/2 in. by 1/8 in. sq such that the long dimension was perpendicular to the spraying direction. For the study of shrinkage anisotropy deposits up to one inch thick were produced. From these, rectangular samples were cut having a longer dimension parallel to the spraying axis. Prior to the addition of activating agent, the samples were deoxidized in hydrogen at 800°C for 20 min. No detectable dimensional or microstructural change was observed after this treatment. The addition of nickel was accomplished by infil-

Jan 1, 1963

By C. B. Alcock, L. I. Cheng

By the use of radiochemical methods for the study of the gas-liquid equilibria at low temperature, and for the determination of the sulfur contents of metal beads which had been equilibrated with H2S/H2 mixtures of known sulfur potential, it has been possible to obtain the liquid solubility and the free energy of solution of sulfur in liquid tin and lead at temperatures between 500°and 680°C. THE gas-liquid equilibrium method has proved in the past to be most successful in the determination of the thermodynamic behavior of dilute solutions of sulfur in liquid metals.1,2 One of the basic requirements for success with this method is that the volatility of both the metal and its lowest sulfide should be small, otherwise sulfide will be deposited at the cool end of the furnace, where it may react with the outgoing gases to form either sulfur-rich lowest sulfide or higher sulfides. The resultant value of the apparent equilibrium constant will then be lower than the correct one. This argument applies even at sulfur potentials below that in equilibrium with a separate condensed phase of the lowest sulfide at the reaction temperature, T. The mass of sulfide which is deposited at the cold end of the furnace, and hence the extent to which further reaction occurs with the outgoing gases, depends on the time taken for equilibrium to be reached between metal and gas. Since this will depend principally on the bulk of the metal phase which is used, one should clearly attempt to uie as small metal samples as possible. These considerations are important in the study of dilute solutions of sulfur dissolved in liquid tin and lead which both have moderately high vapor pressures as metals and form volatile sulfides. The limit on the size of the metal samples which may be used is set chiefly by the difficulties of analysis for very small amounts of sulfur. The oxygen or carbon dioxide combustion method, followed by iodimetric determination of the sulfur dioxide which is formed,has been found to be successful for the determination of small amounts of sulfur in copper, iron, cobalt and nickel.4 This method was unsatisfactory for sulfur dissolved in tin and lead, mainly because the sulfur dioxide was to some extent absorbed by the copious tin or lead oxide deposits which were formed on the walls of the combustion tube. Furthermore some of the sulfur was found to segregate on the surface of the beads as flaky sulfide crystals which would easily be lost in the transfer of a bead from a boat in the gas equilibration apparatus to one in the combustion apparatus. Oxidation in aqueous media to sulfate ion followed by precipitation as barium sulfate was, therefore, adopted as the analytical procedure. The gas-metal equilibrium experiments were all carried out with radioactive sulfur and thus the analysis involved the counting of barium radiosulfate. Furthermore the use of the radioisotope meant that the approach to the gas-metal equilibrium could be followed continuously by gas counting.&apos; The metal beads were held separately in glass crucibles during equilibration and were transferred from the furnace to the beaker for dissolution in nitric acid still in the crucibles, and thus the possibility of sulfur loss by detachment of the sulfide segregates was eliminated. The temperature range of this investigation was 500° to 680°C. EXPERIMENTAL APPARATUS AND METHOD The apparatus consisted of two furnaces placed in series in a gas recirculation system, Fig. 1. One furnace F1, which was vertical was used to heat the alumina crucible, A, holding six metal beads in separate glass crucibles. The beads weighed between 300 and 700 mg each. The crucible assembly was introduced and removed from the furnace mechanically under a stream of oxygen-free argon. The other furnace, F2, was horizontal and was used to heat a cobalt Co9S8 mixture, held in an alumina boat, and made with radiosulfur containing about 1/2 millicurie per g of sulphur. This mixture, which was finely powdered, was used as a source of known H2S/H2 mixtures6 for a given furnace temperature. The recirculation system also contained a gas re-circulation pump (P), an end window Geiger-Miiller counter (N)—placed downstream of F1 so as to monitor the H2S pressure in the gas leaving this furnace— a sample volume for chemical analysis of the gas phase (G), gas drying tubes (D), filling taps and other standard ancillary equipment. The gas sampling volume was principally used in the cali-

Jan 1, 1962

By Leon Merker

FLAME fusion growth of strontium titanate crystals was undertaken to obtain large transparent crystals on which physical data could be gathered. The fact that strontium titanate is a cubic crystal and probably has a high index of refraction indicated that it might be useful in optics. No large boules* of strontium titanate had been synthesized previously, and none have been found as natural occurrences. The flame fusion process, invented by Verneuil in 1904,1 was first applied to grow large crystals of ruby and has since been used extensively to grow crystals of corundum and spinel on a commercial scale. Only during the past nine years has this technique been applied to the growth of large single crystals of other high melting compounds such as rutile,2 mullite,3 and ferrites4 One of several significant advantages of the flame fusion technique over more conventional methods of growing crystals from a melt is that the crystals are grown without the use of melt containers. This fact alone excludes other methods of growing crystals from a melt whenever there are compounds with a melting point near 2000°C or above. Growth of the crystal, similar to that of a stalagmite, takes place inside a circular refractory furnace that does not contact the crystal, Fig. 1. This eliminates a serious source of impurities as well as the likelihood of multi-crystalline solidification along the container walls. The flame fusion technique is particularly advantageous for research because it produces large crystals quickly and at lower cost. A corundum crystal 25 mm long and 12 mm in diam can be grown in 2 to 3 hr. Operating conditions permit observation of the growing crystal during any stage of the process. The various flame patterns and a wide range of oxidation-reduction conditions can be investigated in a relatively short time. It should be pointed out that formation of the foot of the boule is the most critical step in growing an unfractured boule. When the tip of the sintered cone is fused to initiate crystal growth, the original area of fusion should be kept as small as possible so that one crystallite can assume dominance over all the others and propagate as a single crystal. If the boule start happens to consist of several crystals, usually the entire boule also contains several crystals. In many cases these tightly cohering crystals exhibit different crystallographic orientations. Although the basic technique of the original Verneuil process has been retained, refinements in method and burner design have been developed in recent years. For example, boule growth may be initiated on a seed crystal rather than by fusion of a sintered cone. The danger of multicrystalline or twinned boule starts is thus eliminated, and this procedure may also be used to grow boules of predetermined crystallographic orientation. Prior Art: Of the many attempts to produce artificial gem crystals, most early efforts% ere directed toward synthesis of .rubies and sapphires and diamonds. None of these efforts resulted in a process that was commercially practical. Without exception only tiny crystals of corundum were obtained, and those at excessive cost. Verneuil announced his process in 1904; Ravier6 in 1934 presented a detailed description of a commercial boule production plant. Descriptions of the German synthetic stone industry, the process details, and the equipment used have been published by Barnes7 and by Merker.&apos;

Jan 1, 1956

By R. J. Towner

Tensile properties of Aluminum Powder Metallurgy (APM) products at 600°, 800°, and 1000°F were lowered by cold reductions of as little as 10 or 20 pct. The detrimental effect of cold work on yield strength at elevated temperatures increased with temperature. Heating cold-worked products at 850° to 1150°F removed the structural effects of cold work through the process of recovery and restored, at least partially, the strength at 600°F to the level of hot-worked material. Material containing 5 pct A1203 was recrystallized by cold reductions of 97 pct or more followed by annealing at 1100°F. Recrystallization lowered sharply the strength at room temperature, but raised the strength at 600°and 800°F relative to that of the cold-worked state The high strength of Aluminum Powder Metallurgy (APM) products at elevated temperatures&apos;-4 is well-known. In this paper, some conditions of processing that can affect this important characteristic are presented. The following nomenclature will be used to identify different alloys: All of the above alloys are of the aluminum-aluminum oxide type made from milled powders of commercially pure aluminum with the exception of M486, which is fabricated from atomized A1-Fe alloy powder. The products made from milled powders are hardened by a dispersion of aluminum oxide par- ticles in the aluminum matrix, while the intermetal-lic compound FeAL is the dispersion hardening agent in M 486.&apos; The process used for making all APM products involves the application of heat and pressure to form a compact from powder which is fabricated into an extrusion, sheet, strip, or wire by standard techniques. Probably the most common cold-worked APM product is sheet. Cremens, Bryan, and rant&apos; determined the room-temperature tensile properties and the 600°F stress-rupture properties of XAPOOl and XAPOO3 sheet and reported that there was little difference between the as-extruded, cold-worked, and annealed at 1200°F conditions. On the other hand, Emmons6" found that the tensile and stress-rupture properties of XAPOOl and XAPOO3 sheet at 600" and 800°F were lower than those of extrusions. The tensile properties of XAPOO3 sheet were also determined at elevated temperatures by Doyle&apos; and ~ayward.&apos; According to Friske" and Kendal et a1.," cold working by swaging, rolling, and tube drawing reduced the tensile and creep-rupture strength of XAP 001 Recrystallized aluminum powder metallurgy products are rare because the dispersion in the aluminum matrix is usually too fine, uniform, and concentrated to permit recrystallization. However, Lenel12 was able to recrystallize wires made from aluminum powders containing about 1.75 and 3.0 pct oxide and found that the tensile properties at room temperature remained higher than those of annealed commercially pure aluminum because of the dispersed oxide particles. Westerman and Lenel13 found the kinetics of recrystallization of the powder products were very different from those of cold-drawn commercially pure aluminum wire. The alloy containing 3.0 pct oxide recrystallized to a very coarse grain size was more creep-resistant at 400" to 600°C (752" to 1112°F) than in the as-extruded, fine-grained condition, according to Ansell and weertman.14 Ansell and aenel" further studied creep at 500" to 620°C (932" to 1148°F) of recrystallized 1.75 pct oxide wire and confirmed the creep model of Ansell and Weertman. The present work is being reported for the fulfillment of the following objectives: 1) to show the effect of cold work on tensile properties at elevated temperatures;

Jan 1, 1964

By L. Yarborough, L. R. Smith

This paper presents results of a laboratory study of retrograde condensate recovery by revaporization into dry injection gas. Flow tests were performed in 10.6-ft long sand packs at 100F and 1,500 psi. In three runs methane revaporized the liquid from a n-pentane-methane mixture in the presence of immobile water. TWO of these tests were water-wet, and the third was totally oil-wet. In the three runs n-pentane recovery was complete after 2.5 hydrocarbon PV of injection. There was no significant performance difference between the two wettability extremes. In a fourth experiment, a methane-hydrogen sulfide mixture revaporized a synthetic light, sour condensate. No water saturation was present. Equilibrium compositions and volumetric data were obtained for the four-component condensate. The heavy component, n-beptane, was removed after 6 PV production. Comparison of the effluent fluid compositions with known equilibrium data shows that the flowing fluid was equilibrium vapor and that the mixing zone between equilibrium vapor and dry injection gas was short. Data indicated that complete recovery of retrograde liquid occurred after it was contacted by a sufficient quantity of dry gas. INTRODUCTION When pressure declines below the fluid dew point in a gas condensate reservoir, a liquid phase forms. In this process, referred to as retrograde condensation, the quantity of liquid formed is frequently small enough that the liquid is not a flowing phase. To prevent loss of valuable retrograde liquids, the process of dry gas cycling has been employed for several years as a more or less standard practice. In this procedure the reservoir pressure is maintained above the fluid dew point so that the liquid components may be produced as vapor and then separated at the surface. Although full pressure maintenance by gas cycling seems ideal in terms of preventing liquids loss, several factors can reduce the atuactiveness of such an operation. From a study of a condensate reservoir in Alberta, Canada, Havlena et a1.1 con-cluded that cycling under conditions of declining pressure leads to economic advantages and to a high recovery of hydrocarbon liquids. This study considered effects of volumetric sweep efficiency, retrograde behavior of the original wet gas and revaporization characteristics of the retrograde liquid when contacted by dry gas. The first major work concerning revaporization of liquid in a gas condensate system is that of Standing et a1.2 Calculations based upon the PVT behavior of a recombined gas condensate fluid indicated that all retrograde liquid can be recovered if it is contacted by a sufficient quantity of dry gas. The paper considered the effect of variable permeability upon the recovery of retrograde liquid. Standing et al. concluded that recovery of heavier components in the retrograde liquid is greatest if reservoir pressure is allowed to decline below the dew point prior to dry gas injection. Since the work of Standing et al., several laboratory studies have been reported which show that recovery of hydrocarbon liquids by vaporization into dry injected gas can contribute to increased recovery above that obtained by ordinary production practices. Vaporization from retrograde condensate,3 conventional oil4-7 and volatile oil8 reservoirs has been considered. There is little work that deals with revaporization recovery from condensate reservoirs. This study demonstrates that vapor-liquid equilibrium exists when a dry gas is injected into a porous medium containing retrograde condensate; investigates the effect of wettability on revaporization of retrograde condensate; and provides an indication of the amount of dry gas necessary to

Jan 1, 1969

By T. L. Berger, M. C. lnman, M. F. Rose

AFTER shock loading, mechanical twinning has been observed by several authors1-4 for a variety of fcc metals and alloys. It has been shown2,3 that low stacking fault energy materials deform primarily by the formation of mechanical twins and stacking faults during dynamic loading. Further, Inman, Murr, and Rose2 have shown that a correlation exists between the average hardness and the volume percent of mechanically twinned material in stainless steel. It has been observed in nickel&apos; that mechanical twins are produced during shock deformation if the peak pressure associated with the shock wave is greater than 350kbar. It is the purpose of this work to discuss shock-hardening mechanisms in nickel and to determine to what extent the initial condition influences the final response. The "flying plate technique" was used to generate planar shock waves with peak pressures as high as 710 kbar. The details of the technique5" have been discussed elsewhere and will not be repeated here. The material used in this study was polycrystalline nickel of 99.98 pct purity and had an initial grain size of 0.18 mm. Prior to any deformation, all samples were given a stress-relief anneal of 6 hr at 600°C in a vacuum furnace. After annealing, the initial condition of the samples was changed by cold rolling individual samples from 0 pct to a maximum of 80 pct reduction in thickness. This provided samples with controlled initial histories for shock deformation. Immediately after shock loading, the specimens were slowed and quenched by suitable arrangement of buffer material and water bath. This technique minimized specimen damage and the effects of shock heating on the samples. Since deformation twins in high stacking fault energy fcc metals are only produced at high stress levels, the initial defect configuration prior to mechanical twinning should greatly influence the number of twins formed. In fact, Zukas and Fowler7 have found that prestraining in iron and steel greatly suppresses the formation of mechanical twins during the shock deformation process. Following the methods of Warren and warekois8 and Cohen and Wagner,9 X-ray diffraction profile analysis was performed to determine the incidence of stacking faults and mechanical twins in the deformed nickel. Analysis was made on samples in the annealed, cold-rolled, shock-loaded, and cold-rolled—shock-loaded states. The estimated accuracy of the peak position measurements is *0.01 deg in 2?. Therefore the accuracy in the measurement of the relative peak shifts between the (400) and (222) diffraction line profiles is on the order of *0.04 deg in 2?. None of our measurements indicated peak shifts greater than 0.04 in 28. This would correspond to a fault density of -1 pct and sets the limit on the sensitivity of our instrument. Similarly, analysis of the shift in the center of gravity of the diffraction line profiles yields the minimum measurable value of the twin fault probabilitya to be -0.002. Fig. 1 shows mechanical twinning in nickel shock-loaded to 400 kbar. In this photograph, fault intersections are clearly visible. The thickness of the individual fault lamellae was determined from the image widths of their lines of intersections by the

Jan 1, 1968

By D. W. Akins

The case history of a combination gas and water flood instituted early in the life of a field is described. It was recognized from the beginning that recovery would be low, under normal production methods, from the several separate, thin beds of porous limestone which had such poor native permeability that the wells would not produce without acidizing. It is thought that the combination flood gives excellent recovery efficiencies for this type of reservoir. The chief function of the gas flood now is to maintain bottom hole pressure in that part of the reservoir which will not be affected by the water injection program until later. Present estimates are that ultimate recovery will be approximately double the recovery expected under the original solution gas drive mechanism. Wide (80-acre) spacing has enhanced the economics of the over-all field program by the elimination of more than $5,000,000 worth of unnecessary wells. INTRODUCTION The Haynesville Pettit Field was discovered in November, 1941, with the completion of T. L. James Co.&apos;s Callie Akin No. 1, located in the W 1/2 of the NE 1/4 Section 27-23N-8W, Claiborne Parish, La., at an approximate depth of 5,300 ft. The center of the field is about two miles north and a mile west of the town of Haynesville, La. A total of 189 producing wells have been drilled on 14,500 acres. An additional nine dry holes were drilled. The Louisiana-Arkansas state line divides the field so that 34 wells are in Arkansas and 155 are in Louisiana. Governmental sections are divided equally to contain eight production units making 80-acre spacing where the sections are regular. Along the state line in Louisiana there is an irregular tier of sections, each of which contains approximately 456 acres. When divided equally into eight production units the spacing is 57 acres per well for these three and a fraction productive sections. All Haynesville Pettit wells are identified by their section number followed by their position in the section as determined by numbering the production units counterclockwise beginning in the upper right corner of the section. All of the producing wells in the field except two are unit-ized and operated by the Haynesville Operators Committee. These two wells are located in the extreme northern part of the field in Arkansas. Efforts to bring them into the Unit are being continued. The Pettit operators organized the Haynesville Operators Committee and the field became a unit operation May 1: 1944. GEOLOGY The Pettit is Lower Cretaceous in age and is defined as the uppermost porosity in the Sligo formation. The unitized area known as the Haynesville Pettit Field is composed of two separate zones of porosity approximately 40 ft apart and without connection between the two, except in wells. These zones are known as the Upper Pettit and the Lower Pettit. The Upper Pettit is separated into two sections throughout most of its area by a relatively thin but quite impervious shale streak. These are called the "A" and "B" sections of the Upper Pettit. All of these lenticular zones are composed of coquina limestone and a small percentage of normal oolites. The large

Jan 1, 1951

By D. W. Akins

The case history of a combination gas and water flood instituted early in the life of a field is described. It was recognized from the beginning that recovery would be low, under normal production methods, from the several separate, thin beds of porous limestone which had such poor native permeability that the wells would not produce without acidizing. It is thought that the combination flood gives excellent recovery efficiencies for this type of reservoir. The chief function of the gas flood now is to maintain bottom hole pressure in that part of the reservoir which will not be affected by the water injection program until later. Present estimates are that ultimate recovery will be approximately double the recovery expected under the original solution gas drive mechanism. Wide (80-acre) spacing has enhanced the economics of the over-all field program by the elimination of more than $5,000,000 worth of unnecessary wells. INTRODUCTION The Haynesville Pettit Field was discovered in November, 1941, with the completion of T. L. James Co.&apos;s Callie Akin No. 1, located in the W 1/2 of the NE 1/4 Section 27-23N-8W, Claiborne Parish, La., at an approximate depth of 5,300 ft. The center of the field is about two miles north and a mile west of the town of Haynesville, La. A total of 189 producing wells have been drilled on 14,500 acres. An additional nine dry holes were drilled. The Louisiana-Arkansas state line divides the field so that 34 wells are in Arkansas and 155 are in Louisiana. Governmental sections are divided equally to contain eight production units making 80-acre spacing where the sections are regular. Along the state line in Louisiana there is an irregular tier of sections, each of which contains approximately 456 acres. When divided equally into eight production units the spacing is 57 acres per well for these three and a fraction productive sections. All Haynesville Pettit wells are identified by their section number followed by their position in the section as determined by numbering the production units counterclockwise beginning in the upper right corner of the section. All of the producing wells in the field except two are unit-ized and operated by the Haynesville Operators Committee. These two wells are located in the extreme northern part of the field in Arkansas. Efforts to bring them into the Unit are being continued. The Pettit operators organized the Haynesville Operators Committee and the field became a unit operation May 1: 1944. GEOLOGY The Pettit is Lower Cretaceous in age and is defined as the uppermost porosity in the Sligo formation. The unitized area known as the Haynesville Pettit Field is composed of two separate zones of porosity approximately 40 ft apart and without connection between the two, except in wells. These zones are known as the Upper Pettit and the Lower Pettit. The Upper Pettit is separated into two sections throughout most of its area by a relatively thin but quite impervious shale streak. These are called the "A" and "B" sections of the Upper Pettit. All of these lenticular zones are composed of coquina limestone and a small percentage of normal oolites. The large

Jan 1, 1951

By Voyle R. McFarland, Robert A. Burmeister, David A. Stevenson

The distribution of lead between phases in the Ag-Sb-Te system was studied using microautoradio -graphy. Two compositions were investigated, both containing an intermediate phase Known as silver antimony telluride as the major phase, and one containing AgzTe and the other SbzTes as the minor phase. For both compositions, two thermal treatments were used: nonequilibrium solidification from the melt and long equilibration anneals of the as-solidified structure. For each composition, lead was segregated in the minor phase of the as-solidified structure, but was distributed in the matrix after anneal. The electrical resistivity and carrier type were insensitive to the distribution of lead in the two-phase structure. ThERE has been considerable interest in the Ag-Sb-Te system because of its thermoelectric properties. The major interest has been in compositions on the vertical section between AgzTe and SbzTes, particularly the 50 mole pct SbzTes composition AgSbTez (compositions are conveniently expressed as mole percent SbzTes along the AgzTe-SbzTes section). One of the major problems in the proper evaluation and utilization of this material is the inability to control the electrical properties through impurity additions: all alloys prepared to date have been p-type, even with the addition of large amounts of impurities. It has been shown Wit all the compositions previously studied contain an intermediate phase of the NaCl st&apos;ructure as a major phase (denoted by b) and a second phase, either AgzTe or SbzTe3, as a minor phase.&apos;-3 One explanation for the unusual electrical behavior of this material is that the impurity additions have a higher solubility in the second phase than in the matrix; the impurity would segregate to the second phase, leaving the bulk matrix essentially free of impurity.4 In order to investigate this mechanism with a specific impurity element, the distribution of lead between the two phases was determined using autoradiography. Lead 210 was chosen because of the suitability of its 0.029 mev 0 particle for autoradiography and also because of the interest in lead as an impurity in this system.5&apos;6 EXPERIMENTAL PROCEDURE Two compositions were taken from the vertical section between AgzTe and SbzTes, 50 mole pet SbzTes (Viz. AgSbTez) and 75 mole pct SbzTes, in which AgzTe and SbzTes appear, respectively, as the minor phase. Lead containing radioactive lead (pb210) was added to the above compositions to provide a concentration of 0.1 wt pct Pb. The material was placed in a graphite crucible in a quartz tube which was then evacuated and sealed. The samples were melted and solidified by cooling at a rate of 8°C per min and then removed and prepared for microa~toradiography. After autoradiographic examination of these samples, they were again encapsulated and annealed in an isothermal bath at 300°C for a number of days and prepared for examination. An alternate method of preparation employed a zone-melting furnace; the molten zone traversed the sample at a rate of 1.2 cm per hr and the solid was maintained at a temperature of 500°C both before and after solidification. This treatment had the same effect as solidification at a slow rate followed by an anneal for several hours at 500°C. In order to obtain the best resolution, thin sections of the alloy were prepared by hand lapping to a thickness of approximately 20 p. Other samples were prepared for examination by lapping a flat surface on the bulk sample. The resolution, although somewhat better in the former procedure, was adequate in both instances and the majority of the samples were treated in the latter fashion. A piece of autoradiographic film (Kodak Experimental SP 764 Autoradiographic Permeable Base Safety Stripping Film) was stripped from its backing, care being taken to avoid fogging due to static-electrical discharge. A small amount of water was placed on the sample, the film applied emulsion side down on the surface of the sample, and the sample and the film dipped into water in order to assure smooth contact. After drying, the film was exposed for 2 to 5 days, the period of time selected to give the best resolution. The film was developed on the specimen and fixed and washed in place. Two major factors must be considered in establishing the reliability of an autoradiograph: the in-

Jan 1, 1964