Search Documents

By L. P. Davidson

ThE new electrolytic zinc plant of the American Zinc Company of Illinois commenced operation in April 1941. The simple flowsheet using the standard current density and the economic reasons that dictated it are given herewith. The Evans-Wallower Zinc Co. built an electrolytic zinc plant at Monsanto, Ill., in 1929 and operated it for about two years. The plant stood idle from 1932 and was purchased by the American Zinc Co. in 1940. Because of the condition of the equipment, excepting the motor generator set, a complete rebuilding was necessary. The Fairmont City plant of the American Zinc Co. could treat the leach residues, the purification cake and the skimmings from the melting furnace in its various plants. This possibility permitted a simple flowsheet with good economic results. The flowsheet is shown in Fig. I. The calcined concentrates are leached in mechanically agitated tanks with spent electrolyte and such ferric iron solution as necessary. When the acid has been neutralized and the iron coagulated, the fluid is discharged to settling tanks. The underflow from these thickeners is filtered on a Moore filter; the filter cake leaves the plant for retreatment and the filtrate joins the thickener overflow. Zinc dust is added to this solution until the copper and cadmium are precipitated. The pulp is filtered through Shriver presses, which deliver the purified solution to stor- age tanks, and the copper-cadmium-zinc cake is shipped for retreatment and recovery of these three metals. The purified solution is electrolyzed; the regenerated acid is returned for use in the leaching plant and the cathode zinc, after stripping, goes to the melting furnace, from which it is cast in slabs. The skimmings from the melting furnace are shipped to the Fairmont City plant for reduction to metal in the retort furnaces. The choice of this simple flowsheet was made possible only because of the facilities of the Fairmont City plant. The long leaching pried, with high acid content and high temperature which characterize the high-density process, gives a higher zinc extraction but also dissolves more impurities, which must be removed. The same is true to a lesser degree of the multi-step leaching of the western low-density plants. By the sacrifice of some initial extraction, solutions can be obtained that are relatively easy to purify and give good ampere efficiency. This loss in initial extraction is made up in the retreatment of the residues in the Waelz plant. The impurities that accompany the zinc thus extracted are inconsequential when the Waelz product is treated in a distillation plant. It was recognized that this flowsheet would require a somewhat greater amount of sulphuric acid—-eithcr as acid or as sulphate sulphur in the calcine—because of poorer washing. The sulphuric acid plant at Fairmont City could deliver 60" Bè. acid to compensate for the sulphate loss and the cost would be less than the cost of more intensive washing.

Jan 1, 1943

By Mark J. Klein

An internal-friction profile induced by nitrogen in Cr-35 at. pet Re was studied as a function of nitrogen concentration and heat treatment. From these studies, the solubility of nitrogen in this alloy was deduced. The equilibrium solubility of nitrogen in chromium does not appear to be substantially changed by the addition of 35 at. pet Re to chromium. However the precipitation kinetics of nitrogen from solution are significantly decreased. IT has been found that rhenium has a beneficial effect on the low-temperature ductility of Group VI-A metals. As part of a study to investigate the mechanism of this increased ductility, it was of interest to compare the concentration of interstitials retained in solution in one of these ductile bee alloys with the concentration retained in solution in its base metal. In this regard, a study of the solubility of nitrogen in ductile Cr-35 at. pet Re was selected for this phase of the investigation because the solubility of nitrogen in the base metal, chromium, has been determined over a fairly large temperature span.1-3 In addition, nitrogen is known to have an embrittling effect on chromium,4 but does not appear to have a comparable embrittling effect on Cr-35 at. pet Re.5 The experimental method selected for this study was the measurement of internal friction. This technique allows interstitial-concentration measurements to be made in bee metals that are sensitive to small changes in the concentration of a particular interstitial, even when other interstitials are present. When subjected to a cyclic stress, interstitial atoms in solid solution give rise to an internal-friction peak whose origin is the stress-induced ordering of interstitials into preferred lat- tice sites. These internal-friction peaks signify a dissipation of elastic energy which is greatest when the period of oscillation is comparable with the relaxation time for the attainment of an equilibrium interstitial distribution. For dilute interstitial binary alloys, the height of the internal-friction peak is proportional to the concentration of interstitial atoms in solid solutions. snoek8 has shown that the internal friction, Q-1, may be expressed by the equation where A is the relaxation strength, ? is the angular frequency, and 7 is the relaxation time. The relaxation strength, A, is proportional to the concentration of interstitials taking part in the relaxation if no interaction occurs between solute atoms. Thus values of peak height, which can be determined as a function of temperature, give a measure of the relative concentration of interstitial atoms in solution at various temperatures. If equilibrium has been attained, the peak heights will be proportional to the interstitial solubilities. The constant that relates A to the interstitial concentration can be determined experimentally from peak-height measurements as a function of concentration for specimens of constant crystallographic orientation. When this has been done, Q-1 measurements can be used to determine solubilities according to the equation C - KQ-1 where C is the soluble interstitial concentration and K is a constant that can be experimentally determined. It is possible, however, that lattice imperfections may bind interstitials to certain lattice sites. Internal friction does not measure these interstitial~, but does measure interstitials which are free to move in the normal lattice sites when subjected to an applied oscillating stress. On alloying the pure metal with a substitutional

Jan 1, 1965

By A. D. Rich

The term "bleaching clay" or "bleaching earth," as used in the oil industries, refers to clays that in their natural state, or after chemical or physical activation, have the capacity for adsorbing coloring matter from oil. There are three common types of bleaching clays: fuller's earth, activated clays, and activated bauxite. Fuller's earth, or naturally active clay, is prepared from bentonites (see Chap. 5) that possess natural activity. It is not activated commercially; in fact, earths of this type ordinarily do not respond satisfactorily to acid activation. Fuller's earth is prepared in pulverized as well as granular form for use in the contacting and percolation processes, respectively. Acid-activated clays also are of bentonitic origin. The basic raw clay, however, is of a type that has a very low natural activity but is highly activable by treatment with mineral acid. Commercial acid-activated clays generally possess several times the decolorizing power (bleaching efficiency) of the best quality of fuller's earth. The former are prepared commercially only in the pulverized grade because of the difficulties in obtaining a satisfactory granular product, and hence are used only in the contact process. Activated bauxite is made by heat-treating bauxite ore, which in its natural state has very little natural activity. The commercial product is prepared in granular form for use in the percolation process on petroleum oils. For the most part, bleaching clay is used commercially in the decolorization of animal, vegetable and petroleum oils, fats and waxes. It is applied in two ways: (1) by the percolation method and (2) by the contacting method. Percolation refers to the passage of oil through a bed of granular clay whereas contacting refers to direct agitation of oil and pulverized clay followed by removal of the clay from the oil by filtration. In either case, the decolorizing effect is obtained by intimate contact between the liquid oil and the solid adsorbent. Petroleum oils are treated commercially by either the percolation or the contact process. Animal and vegetable oils are treated by the contact process only. Composition The raw clays from which both fuller's earth and acid-activated clays are prepared are composed of hydrous aluminum silicates containing varying quantities of magnesium, iron, calcium and other elements. These raw materials are usually nonswelling bentonites derived from volcanic ash or lava by weathering and hydrothermal chemical reactions. The bentonites have as their chief mineral constituent montmorillonite, which has the formula [(OH)4Si6A14O20•nH2O], according to Grim. (See Chap. 5, ref. 6, p. 91.) The underlying reasons are not fully known for the natural activity of the fuller's earth type of clay and its usual failure to further activate with mineral acid in contrast to the natural inactivity of the activatable type of clay. However, it may be said that the bentonites that are responsive to the acid-activation treatment generally have not undergone any drastic metamorphism. The chemical composition is not a reliable means of discrimination between a nonactive, a naturally active, and a nonactive but activable clay, therefore it is not possible to forecast the ultimate quality of a clay on the basis of the raw-clay analysis alone. Table 1 gives typical analyses of representative clays of the foregoing classifications.

Jan 1, 1960

By H. D. Yoo, M. R. Tek, D. L. Katz

The behavior of gas-storage reservoirs subject to water drive is investigated through analog simulation on an electronic differential analyzer. The simulation technique developed on an LM-10 computer permits the prediction of reservoir volume or pressure resulting from the movement of water in the surrounding aquifer. The method developed on the analog computer consists of setting up an appropriate transfer-function circuit and feeding the arbitrary time-varying boundary conditions as an input signal. The input may be specified as gas reservoir pressure, pore volume or the water flux. Several cases studied include an isolated gas reservoir on a limited aquifer, interference among three reservoirs adjacent to a common aquifer and the growth of gas-storage volume on an aquifer. It is concluded that the method developed on an electronic differential analyzer provides an excellent technique to simulate and investigate the behavior of gas reservoirs subject to water drive. The agreement between the reservoir performance as predicted from the simulation technique and as measured from actual field data is found to be better than the range usually encountered in predicting water-drive behavior. INTRODUCTION It is generally known that some gas-storage reservoirs are located on top of blanket sands of large extent, saturated with brine called aquifers. Because the volume of the body of water associated with aquifers is usually very large and water is compressible, the cyclic pressure variations encountered in normal storage service inevitably cause unsteady, compressible flow conditions in the adjacent aquifers. The solution to radial diffusivity equation for a limited aquifer for constant terminal conditions has been know111 since the early 1930's. The solution for the constant terminal conditions for an infinite aquifer was puhlished in 1949.2 The proldem of handling the unsteady flow of water through a porous medium with time-varying boundary conditions has been studied by many investigators through the use of graphical,3 digital4 computing techniques or on an R-C type of electrical analog called a reservoir analyzer.5 The digital computer performs a series of arithmetic calculations to superimpose the solutions of constant terminal conditions, while the R-C type of analyzer permits the simulation of the continuous medium by means of "lumped-cell" electrical resistance and capacitance elements based on finite-difference approximations. The graphical method is based on the convolution integral solution of the partial differential equalion. The purpose of the present study was to simulate the behavior of an aquifer on a general-purpose, electronic differential analyzer to obtain the influx of water or the change in pressure at the reservoir continuous1r and quickly. The use of the electronic differential analyzer was based on well known solutions for the constant terminal conditions already available in the literature.2,6-8 THEORETICAL DEVELOPMENT MODEL. The gas reservoir (R) is described in relation to an aquifer in Fig. 1. The permeability and porosity of an aquifer sand, the viscosity of the brine, and the compressibility of the brine and the formation are assumed to be constant. It further is assumed that the blanket sand is not thick enough to give appreciable vertical pressure distribution. The model in consideration is circular with radial geometry. The aquifer radius can be of limited or infinite extent. The gas-water interface is assumed to be fully segregated, and the displacement of the gas by

By D. J. Pye

Certain high molecular weight synthetic polymers in very dilute solutions decrease water mobility in porous media 5 to 20 times more than would be expected from the solution viscosity. This indicates that increasing water viscosity to reduce adverse mobility ratios in water floods is economically feasible in many situations. Laboratory results are consistent with accepted theory with respect to improved areal sweep, permeability distribution and displacement efficiencies as would be predicted from the solution mobility measured in the core. The laboratory results have been confirmed by field pilot floods which recovered 80 per cent and 100 per cent more oil than comparative water-flood pilots in fields containing 16 cp and 130 cp oil respectively. Economic analyses based on pilot data indicate the method to be profitable. INTRODUCTION The desirability of improving the water-oil mobility ratio in waterflood-ing operations has long been appreciated, especially for high viscosity crudes. Methods of reducing the oil viscosity by application of heat, gas resaturation and miscible drives have met with some success. Conversely, it has been generally conceded that increasing the water viscosity would also be effective, but the amount of thickening agent required to effect an appreciable increase in viscosity is discouragingly high. The use of such materials as glycerin, sugar, or glycols is completely out of the question economically, so that considerable attention has been given to the use of the much more efficient synthetic water-soluble polymers as viscosity improvers; but even these materials are not economically attractive. If increased water viscosity could be economically realized, marked improvements in areal sweep efficiency, as discussed by Caudle and Wittel and others, would be realized in field operations. Similarly, the improved mobility ratio would bring about increased recoveries by correcting permeability distribution problems as discussed by Stiles2 and Dykstra and Parsons,' and improvements in displacement efficiency would be obtained as recognized by Buckley and Leverett4 and Welge.5 LABORATORY STUDIES THE RESISTANCE EFFECT In the course of research to develop a more efficient water-soluble polymer viscosity builder, we discovered that a very few types of water-soluble polymers exhibited a most unusual and very interesting property not previously observed. Among the earliest materials showing such activity were polymers containing acry-lamide. Fig. 1 shows a typical plot of the solution viscosity vs concentration for one of these polymer solutions as determined in an Ostwald viscometer. As usual, such a plot is an approximate straight line on semi-logarithmic paper. Now, an inspection of Darcy's law, shows that a viscosity value can also be determined in a formation sample if the pressure, flow rate and permeability are known. If the core permeability is previously determined with wa- ter or brine, then the viscosity of another aqueous fluid may be determined from the equation. The viscosities so determined for glycerin (glycol or polyvinyl alcohol solutions, for example) agree with the viscometer determinations. However, in the case of the water-soluble polymer solutions in which we are interested, the viscosities measured in the formation sample depart very markedly from the viscometer values. A typical relationship for a polymer solution is also shown in Fig. 1. This unusual departure from the expected response is referred to as a resistance property of the polymer and is quantified as "resistance factor". Since the resistance factor R can best be determined in a core under study, the term has been defined on the basis of the ratio of the brine mobility to the polymer solution mobility at residual oil saturation so that:

Jan 1, 1965

By Jim D. Mote, Eugenia M. Howard, Willis L. Barmore, John E. Dorn

The effect of stress and temperature on the creep rate of Ag-33 at. pct A1 and Ag-33 at. pct Al-1 at. pct Zn for prismatic slip was determined over a range of temperatures from 440º to 700°K. The alloys exhibited a brief initial inverted transient creep over which the creep rate increased slightly to a steady-state value which depended only on the stress and temperature, regardless of the previous strain history. The steady-state creep rates were found to be given by: where the activation energy is independent of the stress and strain and agrees fairly well with that estimated for diffusion. The observed creep behavior was shown to be in qualitative agreement with a model based on the stress-induced local disordering in the vicinity of a dislocation. OVER the past fifteen years, considerable progress has been made in correlating the experimen-entally observed plastic behavior of pure metals over each temperature range with one or more of a series of theoretical strain-rate controlling dislocation mechanisms. Despite the current interest in the plastic behavior of intermediate phases and inter metallic compounds, however, very little has been done in identifying the operative dislocation mechanisms in these materials. It is anticipated that the plastic behavior of intermediate phases can be rationalized in terms of the same dislocation mechanisms that are appropriate to pure metals and a solid solutions, provided the additional complexities arising from crystal structure, bonding, long-range order, short-range order, and defect lattices are taken into account. As part of a more extensive investigation on the plastic behavior of intermediate phases, Mote, Tanaka, and Dorn1 recently reported on the effect of temperature on the yield strength for prismatic slip in the hexagonal Ag-33 at. pct A1 intermediate phase as recorded in Fig. 1: Over Region I the deformation was observed to take place as a result of the thermally-activated Peierls mechanism, and over Region II the athermal disordering mechanism applied. The experimental data at that time, however, were not sufficiently extensive to identify the thermally activated mechanisms operative over Region III. It is the purpose of this investigation to attempt to identify the mechanisms that are operative over this high-temperature region. It will be shown that the same mechanism operates all over Region Ill, although the activation energy for this mechanism is in good agreement with that for diffusion, the process cannot be attributed either to the motion of jogged screw dislocations or the climb of edge dislocations. The results, however, are in good qualitative agreement with stress-induced disordering localized at dislocations. EXPERIMENTAL PROCEDURE The alloys studied in this investigation were prepared from silver, aluminum, and zinc (each of purity greater than 99.995 pet) by induction melting under an argon atmosphere and chill casting in a copper mold. Rectangular bar single crystal specimens (1/4 by 1/8 in. in cross-sect ion) of Ag-33 at. pct Al were grown in vacuum by a modified Bridgman technique. Similar Ag-33 at. pct Zn specimens were produced by an identical technique employing an argon atmosphere. The specimens were so oriented that the angle 90-Xo between the tensile axis and the normal to the prismatic plane and the angle A, between the tensile axis and the slip direction were 45 ± 1 deg. The effect of a change in temperature on the creep rate and a change in stress on the creep rate were determined over the temperature range

Jan 1, 1963

By M. C. Miller, M. R. Tek, D. L. Katz

Previous studies have shown the influence of geometric variations on the drawdown and buildup behavior of a well completed in a homogeneous, porous medium containing a single-phase fluid. Other papers have shown the influence of leakage across caprocks on drawdown tests on water wells and aquifers. This paper presents two additional cases: the influence of an adjacent, expansible source of fluid, and the effect of caprock leakage on the measured in situ permeability and compressibility. Methods are developed for evaluating the influence of these two deviations from a uniform aquifer upon the in situ permeability and compre.ssibility indicated by pump tests. INTRODUCTION In relatively uniform porous media, saturated with a single-phase fluid, the effective reservoir permeability and compressibility of the water porous bed system may be obtained from drawdown and build-up data on wells, such as the initial wells drilled in aquifer storage reservoirs (Homers and Katz et al.7). In considering the drawdown and build-up behavior of wells adjacent to storage reservoirs, or of wells in an aquifer adjacent to an unknown gas field, questions arise as to the quantitative effect of the presence of compressible fluid on the measured permeability and compressibility of the formation. The solution to this problem is presented, using a constant pressure line source at some distance from two wells, one of which is pumped and the other used as the pressure observation well. The solution is presented in terms of the geometry of the wells and their relationship to the constant pressure line. It is known that caprock leakage can interfere with the determination of an aquifer in situ permeability and compressibility (Mantush4, Hantush and Jacob3 and Witherspoon and Muellerll). This paper presents an added case of the effect of leakage through a caprock of known thickness and permeability on well tests starting with a reservoir of constant pressure above the caprock and contributing to the aquifer as a result of the pump test. Again, both a pumping well and an observation well are postulated. These two cases are presented together since both a compressible fluid nearby and. caprock leakage show similar deviations from expected in situ permeability and compressibility results, and the solutions are similar in form. EFFECT OF A NEIGHBORING CONSTANT PRESSURE SOURCE ON IN SITU MEASUREMENTS Bixel, Larkin and van Poollenl presented a paper showing the influence of a discontinuity of the properties of a fluid formation system on drawdown and build-up performance. Their case is related to the present study but may be distinguished from it in that their numerical work and resulting graphs relate only to the performance of the pumping well itself. Incorrect values for in situ reservoir properties may be obtained from pump test data if the skin effect of the well and after-flow are not considered. Analysis of this problem by the authors indicated that the more reliable method of evaluating the influence of an adjacent gas field or expansible source was to use one well for pumping and another well at some distance from it for observing the aquifer pressure performance. An expansible source of hydrocarbon near a pumping well may be approximated by a line of constant pressure for a pump test. Fig. 1 illustrates a pumping well and an observation well near a line of constant pressure. Pressure behavior of an observation well during a drawdown pump test near a line of constant pressure is given by the diffusivity equation:

Jan 1, 1967

By J. A. Snyder, W. L. Finlay

G. Edmunds—Solid solubility is considered to be of either the interstitial or the substitutional type. Is it possible, in a binary alloy as the simplest case, that some of the solute atoms are present in the normal lattice sites (substitutionally or filling lattice vacancies) while simultaneously others are in interstitial positionss One might even ask whether a distribution of the two types may be the normal situation. H. M. Meyer—Metastable states of interstitial atoms occupying vacant lattice sites possibly occur as well as of substitutional atoms squeezed in between regular matrix positions. However (as we know since Hume-Rothery), the solute atoms choose between the two kinds of solutions; consequently, every solute will be unequivocally either substitutional or interstitial in the equilibrium state of the solid solution. M. Balicki—In view of the fact that the authors apparently correlate the analysis of the alloys at the ingot stage with the properties exhibited at the testing stage, I would like to ask whether this is a fully justifiable procedure. In other words, how good are their determinations of solute concentration for correlating them with the mechanical properties. The answer to this question may explain some of the divergencies. Assuming good enough homogenization of the samples and exact determination of mechanical properties the position of the plotted experimental points will depend solely upon the accuracy of composition determination. If this is not accurate, say due to loss or pickup of elements during processing from the ingot to the testing stage, or due to a systematic error in the method employed for obtaining solute concentration data, the points will deviate from their true position and may align themselves along a different curve than the one expected. H. V. Kinsey—We have been studying the creep-rupture properties of titanium-base alloys at 1000°F. In the course of this work, anomalies in behavior of the alloys that would suggest that the material under test was becoming stronger as the test progressed have been observed. If this was so, the most likely explanation that we could think of was that the test bars were absorbing oxygen and nitrogen from the air during the test and were thereby becoming strengthened. In an attempt to determine the strengthening effect of absorbed oxygen and nitrogen the following experiment was conducted. A length of cold-rolled titanium was supplied by the E. I. du Pont Co. Two test bars, having a 1/4 in. diam gauge length, were prepared from this material. One bar was tested in the as-received condition. The second bar was heated in air at 1550°F for 100 hr and subsequently air cooled prior to testing. A testing temperature of 1000°F was employed. The results of these tests are tabulated in table 11. In the author's opinion, is it reasonable to assume that the bar that was exposed to air at 1550°F for 100 hr was stronger because it absorbed oxygen and nitrogen from the air during this heat treatment? W. L. Finlay (authors' reply)—Direct experimental evidence for or against Mr. Edmunds' interesting suggestion will probably never be available. It seems possible, however, that mixed interstitial-substitutional solid solution might well occur with interstitial elements. The less likely possibility of interstitial solution of a normally substitutional element like copper in aluminum was recently discussed at length by the

Jan 1, 1951

By Caudle B. H., Cooper H. E. Jr., O. K. Kimbler

The results of studies of areal sweepout behavior in nine-spot injection patterns are presented in this paper. The ratio of the production rates of the two types of producing wells in a nine-spot pattern is considered in its effect on breakthrough. A model study was used to develop a method to predict the production histories of both side and corner wells and to develop the production history of the pattern or the field. INTRODUCTION The importance of areal sweepout behavior in injection operations has been recognized for a number of years. We now know that the fraction of a reservoir which will be reached by an injected fluid is a function of the geometric arrangement of the production and injection wells and of the mobility ratio of the fluids. Of these two, the mobility ratio (which is a measure of the relative ease with which the oil and the injected fluid can move through the reservoir) appears to have the greatest effect on recovery. The effect of mobility ratio on production history has been reported for most of the dispersed injection patterns (i. e., five-spot, staggered and straight-line drives).4-6 ere has been very little published on the nine-spot injection pattern. This may be because the two types of producing wells in the nine-spot pattern can—and sometimes should —be produced at different rates. This adds a second variable (the fist being mobility ratio) to be covered in a study of the nine-spot flooding network. Muskat1 has reported the sweep pattern efficiency at breakthrough for a mobility ratio of one at various ratios of producing rates for the two types of wells. For these conditions he found maximum oil production at breakthrough to occur when the corner well (the producing well farthest from the injection well) is produced 10.7 times as fast as the side well. Other investigatorsa2,3 have studied a few of the many possible operating conditions possible with this injection pattern. This paper presents the results of studies which are strictly applicable to a nine-spot injection pattern surrounded by other nine-spots in a homogeneous reservoir and which has no flowable gas present (no oil bank is formed). Although the full ranges of the variables mentioned above have not been covered, the results reported here should allow reasonable estimates of field operations to be made. EXPERIMENTAL The well spacing geometry of the nine-spot pattern is shown in Fig. 1. Here we see that each injection well is surrounded by eight production wells arranged in a square. Four of these producing wells are located at the corners of the square; the other four are in the midpoints of the four sides. These two types of producing wells are called "comer wells" and "side wells" respectively. It is the ratio of the producing rates of these two types of wells that affects the breakthrough recovery, as calculated by Muskat.' This ratio is defined as the total producing rate of a corner well divided by the total producing rate of a side well. The model used in this study represented one-eighth of a nine-spot pattern, as shown in Fig. 1. It contained the equivalent of one-fourth of a side well, one-eighth of a comer well, and one-eighth of an injection well. Because of these proportions, the actual producing rate ratios in the model were one-half of the ratios of producing rates as

Jan 1, 1965

By Thomas E. Garnar

Zirconium and hafnium are curious elements because they are almost always found together in nature. Zirconium was discovered by Klaproth in 1789 and isolated 35 years later by Berzelius. Because hafnium's chemical properties are so close to those of zirconium, it was not discovered until 1923 when Coster and Von-Heresey detected it using x-ray spectrographic analysis. These elements occur most commonly in nature as the mineral zircon (ZrSiO4) and less commonly as the oxide baddeleyite (ZrO2). They also are found as a variety of other silicates. Zircon was identified as a component in alluvial and beach sands in 1895, but it was not produced in any quantity until 20 years later. Zircon is always a coproduct from TiO2 mining and processing. During World War I it was produced as a coproduct of beach sand mining for titanium minerals just south of Jacksonville Beach, FL, and was patented as a refractory. It was not until the 1930s when Zircon Rutile, Ltd. began mining at Byron Bay on the east coast of Australia that zircon was first used as a foundry sand. Later in the 1940s, NL Industries, Humphreys Gold Corp., and E. I. du Pont de Nemours & Co., Inc. began production of zircon sands from fossil beaches in northeast and northcentral Florida. Baddeleyite first became available as a commercial product in 1916, but never in the quantity of zircon. Zircon holds a unique position as an industrial mineral because it is used for both its physical and chemical properties as well as an ore of zirconium and hafnium metals. Australia is the major zircon producer followed by South Africa and the US. Zircon is also produced in India, Sierra Leone, Sri Lanka, Malaysia, China, Thailand, and Brazil. Undeveloped heavy mineral beach sand reserves containing zircon are known to occur in Egypt, Malawi, Senegal, and Tanzania. Locations are shown in Fig. 1. Mineralogy Zirconium and hafnium are always present together in naturally occurring compounds. Most commonly they form as the silicate sometimes containing iron, calcium, sodium, manganese, and other elements. Less commonly they are found as oxides in combination with titanium, thorium, calcium, and iron. Zircon is the most common form. It is extremely resistant to weathering, therefore, often it is present in ancient beach sands and placer deposits. Although resistant to alteration from external sources, it is vulnerable to internal alteration as the result of thorium and uranium substituting for zirconium either in the zircon lattice or in solid solution. Alteration to the metamict state takes place as radioactive emanations from these elements disorder the crystal lattice, accompanied by hydration, reduction in specific gravity, and changes in color. The mineralogy of zircon and baddeleyite and variation of physical and chemical properties are shown in Table 1. The effects of zircon's internal alteration and darkened color can be corrected by heating to 1000°C for 30 min or so. A certain time-temperature relationship makes it possible for decolorization and reordering of the crystal lattice to take place when heating at higher temperatures for shorter periods or at lower temperatures for longer periods. After heating, x-ray diffraction patterns are sharper, the grains may be harder, and except for particles of malacon, the grains will be white or colorless in the absence of grain surface coatings. The color change is only temporary and the particles slowly darken with time. Zircon fluoresces light yellow in shortwave ultraviolet light. If exposed to ultraviolet light for extended periods of time, white (calcined) zircon turns purple. With time the induced color begins to fade and eventually disappears (e.g., calcined Florida zircon exposed to ultraviolet light for 24 hr still retains faint, but discernible, purple color after six months).

Jan 1, 1983

By N. S. Stoloff, R. G. Davies

The annealing behavior of a heavily cold-worked FeCo-V alloy has been studied at temperatures both above and below Tc, the critical temperature for ordering. It was found that re crystallization and grain growth can take place below Tc in the ordered state and that, in agreement with results for fcc alloys, order retards grain growth. The activation energy for pain growth is -55 kcal per mole in the disordered condition; it was not possible to assign a value to the activation energy for grain growth below Tc because the degree of order is changing rapidly over the temperature interval investigated. Precipitation of an fcc y phase was observed upon annealing the cold-worked alloy at temperatures of 675°C and below. SINCE it is known that diffusion constants are greatly affected by long-range order,' it is not unreasonable to anticipate that order will influence the diffusion-controlled phenomena of recrystallization and grain growth. In the course of a study of strain aging of ordering alloys around the composition Ni3Fe Vidoz, Lazarevic, and cahn2 noted that a disordered cold-worked alloy annealed at a temperature T1 just below Tc will order but not recrystallize; Tc is the critical temperature for order. The same alloy annealed at a temperature T2 just above Tc, or an alloy of different (nonordering) composition annealed at either T1 or T2, will recrystallize after equivalent amounts of cold work. Initially Selisskii and coworkers,3,4 who examined a series of cold-worked and annealed bcc Fe- Co alloys, reported that alloys forming the B2 FeCo super lattice could not be recrystallized below Tc. However in a later paper5 it was shown that FeCo ordered alloys could be recrystallized below Tc. Thus the first question to be answered by the present investigation was whether or not a heavily cold-worked Fe-Co-V alloy could be recrystallized below Tc. When it was found that the alloy would indeed re-crystallize below Tc, the influence of long-range order upon subsequent grain growth was studied. EXPERIMENTAL PROCEDURE The grain-growth measurements were made upon FeCo-2 pct V wire of 0.031 in. diam; the alloy was the same as that used in an earlier study of the mechanical properties of FeCO-v.6 The wire was produced by cold swageing and drawing a rod 0.125 in. diam that had been quenched into iced brine from 850°C to disorder the alloy; the initial grain size was 0.05 mm. Rates of grain browth were measured after isother-mally annealing the wire in the temperature range 675° to 825°C; T, is -720°C. Grain diameters were measured on the transverse cross section of the wires. The line-intercept method of determining the grain diameter was used; conventional light photomicrographs were taken when the grain size was greater than 10 . Carbon replicas were produced and examined in the electron microscope if the grain size was less than Dislocation configurations after recrystallization anneals were studied by electron transmission microscopy of foils produced by cold rolling a 0.125-in.-thick strip of the quenched material to 0.012 in. The foils, after heat treatments similar to the wire samples, were thinned by electropolishing in a chromic-

Jan 1, 1967

By J. A. Herbst, D. W. Fuerstenau

This paper examines the zero order production phenomenon in the context of the size discretized batch grinding model. A restrictive interrelationship between the selection and breakage parameters of the model, which is mathematically sufficient to ensure zero order behavior, is delineated. Based on this interrelationship, a scheme is developed for predicting the values of the selection and breakage parameters for all size fractions from a minimum of experimental data. To test this scheme, dolomite was ground in a laboratory batch ball mill. Successful simulation of the comminution behavior of this system was achieved using the batch grinding model with the parameter values obtained from the proposed scheme. Historically, a preponderance of comminution research has centered on attempts to relate breakage energy to the performance of comminution machines. Concomitantly, grinding data were interpreted almost exclusively in terms of inherently empirical energy-size reduction relationships1-3 or "laws of comminution"4- 6 which were based on highly oversimplified descriptions of the fracture process. In some instances, these relationships provide a crude basis for the correlation of experimental data, but, invariably, this approach is inadequate for meaningful process simulation. The control and optimum design of comminution circuits require a mathematical model capable of depicting the size reduction behavior of every size fraction for grinding conditions of technological importance. Energy-size relationships do not provide this detailed information. For example, an energy-size analysis for batch ball-milled dolomite has recently been completed in the authors' laboratories.7 This analysis provided a satisfactory correlation between the hypothetical size modulus, which characterizes only the finer portion of the size distribution, and the input energy. However, this relation did not constitute an adequate description of the complete system. In general, one of two distinct viewpoints toward simulation has been adopted in recent comminution research. The first approach focuses on the fracture of single mineral specimens, with the essential aim of representing the over-all process in terms of the breakage characteristics of individual particles and the characteristics of the stress field which the particles experience within the particular size reduction device. As illustrated by Harris's review,' the actual incorporation of single-specimen fracture information into a description of the behavior of a multiparticle comminution system has seldom been attempted. The only model to accomplish this incorporation was the one developed by Schönert.8 The Schonert model treats single-passage grinding machines in terms of a distribution of effective loads acting on a particle, a distribution of required particle breakage energies, and the breakage product distribution. However, the use of single-particle fracture behavior to derive models of the size reduction process is at present limited to machines in which the particle residence time is approximately equal to the time required to apply stress. As a result, Schönert's analysis cannot be used to advantage to simulate the complex environment which prevails within a tumbling mill. For multiple-passage systems a second approach to the description of comminution processes has been more fruitful. This approach entails the formulation of a mathematical model which is phenomenological in nature in that it lumps together the entire spectrum of stress-application events which prevail in a system under a given set of operating conditions. The appropriately defined average of these individual events is then considered to characterize the over-all breakage properties of the device. Thus, to analyze the performance of a tumbling mill, the manner in which the particles of a particular size (or size fraction) are stressed need not be distinguished. Instead, a single parameter is assumed to represent the resistance of that size to fracture, given the average grinding environment which exists in the mill. The isolation of such a parameter and a related set of quantities, which constitute the breakage product size distribution for the average event in this size fraction, allows the formulation of physically meaningful descriptive equations capable of yielding precise and detailed information for simulation.

Jan 1, 1969

By R. P. Alger, C. A. Doh, M. P. Tixier

The principle, the equipment and field operation of sonic logging are described. The tfio-receiver system produces logs independent of hole size and mud. Field experience is given and forms the basis for the interpretation of the log. The derivaiion of porosity values from measured velocities is discussed, according to the type of formations (hard formations, compacted sands, and unconsolidated formations). The time-average equation proposed by M. R. J. Wyllie, A. R. Gregory and L. W. Gardner is uscd as a basis for the computation of porosity in limestones, cemented sandstones and compacted sands. Variations in the lithologic character of limestones do not seem to change the porosity calibration markedly. The compaction of sands is related to the compaction of shale adjacent to them; and, thus, the shale velocity is used for the establishtnent of empirical relations for the computation of porosity in un-consolidated formations. Various forrnu.las are tentatively presented to account for shale and fluid content. Field experience demonstrates that considerable attenuation of sonic energy takes place in unconsolidated formations, particularly when gas bearing, and in fractrured formations. Unusually large attenuation produces skipped cycles, a feature easily recognized. The application of sonic logging to structura1 studies is featured, showing its possible integration with the dipmeter. Correlation and its application to the irrterpretation of seisrmic surveys are reviewed. The paper is illustrated with field examples. Sonic logging is the recording of the time required for a sound wave to traverse a definite length of formation. Sonic travel-times are inversely proportional to the speed of sound in the various formations. The speed of sound in subsurface formations depends upon the elastic properties of the rock matrix, the porosity of the formations and their fluid content and pressure. Below the "weathered" or low-velocity layer extending from 50 to 100 ft or so below the surface, sound velocities may range from about 6,000 ft/sec in shallow shales to as much as 34,000 ft/sec in dolomites. In hard formations (well cemented and/or compacted), the sonic log reflects the amount of fluid in the formations; hence, it correlates well with their porosity. In unconsolidated formations, which are usually of fairly high porosity, the sonic log gives an approach to porosity determination, when its readings are corrected for lack of compaction, shaliness, and fluid content. In such formations the sonic log may also indicate the presence of gas and may distinguish between oil- and water-bearing beds. Field experience with the sonic log in soft formations is more limited than that in hard formations. As a result, interpretation in soft formations is not as well developed at the present time. In all types of formations the sonic log is of considerable value for correlation and for the more detailed and accurate interpretation of seismic data. EQUIPMENT AND PRINCIPLE FIELD OPERATION The basic features of the sonic log" are a two-receiver system and two available short spacings. The log is recorded on film using a standard field unit. An SP curve is run along with the sonic curve to give a more interpretable log and to establish absclute depth control for comparison with other logs run in the same well. If desired, a gamma-ray curve may be recorded simultaneously with the sonic curve. Fig. 1 shows the sonic-gamma ray combination sonde. The sonic portion consists of a sound transmitter and three receivers mounted 3, 4 and 6 ft from the transmitter. When the first and second receivers are used, a sonic log of I -ft spacing (distance between receivers) is obtainea. Use of the first and third receivers provides a 3-ft spacing. The transmitter emits pulses at the rate of l0/sec. After the transmission of a pulse the first arrival of sound energy at each receiver triggers its response system. The differ-

By N. E. Garner

Laboratory experiments were conducted to investigate the cutting of a single diamond on limestone and shale under simulated down-hole conditions. A high-pressure chamber was modified by adding a rock-rotating device so that planing tests could be run. Weight on the diamond, diamond geometry and differential pressure across the face of the rock were varied. It was found that (I) high differential pressure reduced the volume of rock cut by the diamond at a given bit weight by strengthening the rock and changing the mode of failure; (2) a finely powdered rock left in the bottom of the grooves reduced the volume cut by as much as 50 percent; and (3) orientation of a single diamond about the axis of a drill point had considerable influence on diamond cutting efficiency. INTRODUCTION Diamond bits consist of many diamonds held in a matrix provided with water courses for fluid passage to clean, cool and lubricate the diamonds as they drill formation. Each diamond contributes its share to the overall effectiveness of a bit, but a lack of understanding of the performance of a single diamond has hampered efforts to engineer improvements in diamond bits. The need for those improvements prompted this study. This paper describes the findings of a laboratory investigation of the outting action of a single diamond where the differential pressure between the wdlbore and formation, diamond geometry and vertical force on the diamond were independently varied. The tests were conducted in a pressure chamber that provided relative horizontal motion (planing) between a rock and diamond under simulated down-hole pressure conditions. EQUIPMENT HIGH-PRESSURE CHAMBER WITH ROTATING DEVICE The high-pressure chamber used in previous rock mechanics studies' was modified for this study by addition of a rock-rotating device. The modified chamber (Fig. 1) differs from the old chamber in that the rock can be rotated to provide relative horizontal movement between the rock and the penetrator which may be a small element of a diamond or a drag bit. In this study the penetrator was a single diamond. The rock sample holder inside the chamber is mounted on a thrust bearing and is connected to the external drive mechanism by a stem that passes through two seal elements. The seal elements are needed to allow formation pressure to enter the bottom of the rock sample through a small hole in the stem. The Kapseal seal elements (Tefion boots backed by O-rings) provide low friction (hand free) even at differentials of 5,000 psi. The drive mechanism is a variable-speed transmission with a speed range from 0 to 30 rpm and an output torque of 2,800 in.-lb. A right-angle-drive gear box couples the drive to the stem. The new design has two independent pressure systems (formation and borehole) to simulate down-hole rock stress environment. Formation pressure enters from the bottom of the rock through a 6-in. diameter area, and borehole pressure acts over the remaining surface. A 14-in. layer of zero fluid loss oil-base mud poured over the top of the rock and an O-ring seal on bottom allow a differential between the borehole and formation pressures. Bayol 50 was used as the hydraulic fluid in the chamber. The differentials reported here were obtained by elevating the borehole pressure while keeping the formation pressure at zero.

By H. W. Mead, C. E. Birchenall

The rates of growth of graphite nodules in cast irons are calculated for a model of a growing graphite sphere surrounded by a shell of austenite through which carbon and iron are diffusing. The carbon is supplied by a cementite-austenite mixture at the outer edge of the shell. The calculated rates from carbon diffusion agree fairly well with the measured values, but the rates based on iron self-diffusion are much too low. Because the iron must be removed for the process to continue, o plastic deformation mechanism is suggested. THERE has been an unfortunate tendency in the literature of growth and dissolution reactions to identify the slope of a plot of the logarithm of the growth or dissolution rate vs reciprocal of temperature with the activation energies determined by diffusion measurements in chemically similar systems. If the solubility limits at the growing or dissolving phase interfaces change appreciably with temperature, such procedures may lead to serious errors in specifying the mechanisms controlling the rates of these processes. A reaction involving the simultaneous growth of graphite from and dissolution of cementite in austenite will be discussed here to show that substantial oversimplifications have been made in earlier studies of this process. From a dilatometric study of the overall y-range graphitization process, Bunin and Danil'chenko' found an apparent activation energy of 90 kcal per g-atom. They concluded that, since this value was much nearer the approximately 68 kcal per g-atom observed for self-diffusion in pure iron than it was to 32 kcal per g-atom for diffusion of carbon in iron, the rate-controlling process must be the diffusion of iron away from the growth interface to provide space for graphite to grow. Bunin and Salli' bolstered this agreement with the observation that graphite forms preferentially at surfaces, cracks, and pores where free volume is present initially. Ziegler, Meinhart, and DeaconQ ad found an apparent activation energy for graphitization of 98 kcal per g-atom. This value, like that of Bunin and Danil'chenko, applies to nucleation and growth occurring simultaneously. It is not generally assumed that nucleation is entirely diffusion-controlled. Treatments such as prior cold-working and prequenching, which strongly affect the rate of graphitization, would be expected to have little effect on diffusion processes occurring at the graphitization temperature. In any case 90 kcal per g-atom is not particularly close to the 54 kcal or lower to be expected for diffusion of iron which is carbon-saturated.' The presence of silicon in iron is said to reduce the activation energy for diffusion,' so its presence in cast irons would be expected to have a similar effect. The growth rates of nearly spherical graphite nodules have been studied by Brown and Hawkes." The initial rate of growth before impingement of adjacent carbon-depleted areas was found to be parabolic, and rate constants were measured at several temperatures. Their apparent activation energy for the growth process only was roughly 45 kcal per mol. Burke and Owen' made growth-rate measurements on several alloys, recording appreciable induction periods, initial nucleation rates, and average radial growth rates based on an assumed linear rate of radial growth. They found that increased silicon content increases the ovel-all reaction rate and the initial rate of nucleation, and decreases the induction period. Assuming 1) spherical nodules. 2) constant volume rate of nucleation, 3) austenite in equilibrium with cementite at positions where the cementite is not depleted, and 4) a constant diffusion distance during the growth of a nodule, they calculated an apparent overall activation energy of 68 kcal per mol, which was related to an activation energy for nucleation of 79 kcal per mol and activation energy

Jan 1, 1957

By L. H. Sjodahl, J. B. Conway

of each particle on grain boundary movement is proportional to the area it occupies on the grain boundary and this increases with the square of the particle radius. In contrast to the impression gained by Tiwari the effectiveness of a particle, as a grain boundary obstacle, increases rapidly as the particle size increases. The counterbalancing factor in a dispersion of constant volume (e.g., those considered by Zener) is of course the rapidly diminishing number of particles, a situation which does not exist in thoria dispersed materials where the volume fraction of thoria remains constant. Although it has been assumed that the Zener approach is valid for the sake of the above argument, it is open to the following objections: 1) It assumes that the effect of many small particles along a grain boundary is cumulative and does not take into account the possibility of each small particle being overcome separately. In this case the boundary will not be able to move forward until the largest particle on the boundary has been overcome. This means that the rate controlling factor will be the rate at which a few relatively large particles are overcome with the remaining small particles playing a negligible role. 2) When the dispersion consists of very small particles the interparticle spacing is usually small compared to the grain size and most particles are located away from grain boundaries where they can play no part. The most efficient dispersion, from a purely geometrical viewpoint, is one where the particle spacing is equal to the grain size so that all the particles are on grain boundaries. Tiwari's second point that voids cannot prevent re-crystallization seems to be unfounded as several workes20-23 have shown that voids alone can retard grain boundary movement and recrystallization. To further convince Tiwari, Fig. 17 shows a void in deformed TD Nichrome holding back a recrystallization interface. Tiwari's explanation for the effect of voids on recrystallization, i.e., they reduce local strain energy and hence lower the driving force for recrystallization may be valid in itself but is irrelevant to the present case where even complete recrystallization after ONE of the more recently proposed expressions for describing stress-strain behavior is that due to Voce.1,2 This equation is usually written: s =s8 ?(s8?so)e??/?c [l] where s is the true stress, ? is true strain, cC is a constant called the characteristic strain, s8 is the asymptotic stress approached at high strain values, and so is the threshold stress at which the plastic deformation begins. While this expression has not been universally accepted as yet it does contain certain features which are consistent with experimental stress-strain behavior. In a more recent publication Hsu, Davies, and Royles3 employed the concept of generalized strain proposed by seth4 and identified a method for linearizing the stress-strain plot. In this approach the generalized strain was given by: where 7 is the generalized strain, 1 is the instantaneous length, 1, the datum length, and n is a constant called the "coefficient of strain measure". A value of n was said to exist which would yield the linearity: s —s+ S[.-(tf] [3] In recent studies of both these approaches, it has been found that while the Voce equation and the gen-

Jan 1, 1970

By W. W. Krysko

In order to calculate the critical particle size of lead oxide entrapped in lead, Stoke's Formula may be applied. All data were available except figures for the density of lead oxide at elevated temperatwes. The density of lead oxide was determined by means of dilatometmetrc and volumetric methods up to 1010°C. Graphs of the density of lead and lead oxide as well as the viscosity of lead are given and discussed, with the conclusion that the most unfavorable region for the separation of lead oxide from molten lead lies just above the melting point of lead. DURING previous investigations, particularly on the dedrossing of lead with aluminum1 and the oxygen solubility in lead,' the critical particle size of lead oxide which could be entrapped in solidifying lead was estimated by calculation, and it was shown that high values found for the oxygen content of lead may be due to the method of sampling and the entrapped particles of dross. Unfortunately, due to lack of data, an exact mathematical solution was not possible. The particle size which will separate under a given condition can be estimated from Stoke's Law, which states that where: d = diameter of the critical particle size ¦q = viscosity of lead in Poise V = constant velocity in cm sec-I g = 981 cm sec-2 61= specific gravity of lead 62= specific gravity of lead oxide The depth of the lead bath and the time before solidifying define the velocity. The viscosity of molten lead is known from earlier work by Krysko and is given in Table I. The specific gravity of lead is also known, see Table II. These values are according to Hofmann. A careful survey of literature revealed no values for the density of lead oxide at elevated temperatures. The present investigation was therefore conducted to provide this information. RESEARCH INVESTIGATIONS The density of lead oxide was determined from the following experiments: 1) Determination of the density of lead oxide at room temperature. 2) Dilatometric investigations on the same samples. 3) Determination of the shrinkage at the liquid-solid trans£ormation. 4) Density determinations on liquid lead oxide. 5) Time temperature curves during cooling. 1) The samples for the determination of the density of lead oxide in the solid state were prepared in the following manner. Molten lead oxide was cast into I hot mold which could be opened along the longitudinal (vertical) axis. The cast samples were cylinders of approximately 10 mm diam and approximately 80 mm length. The cylindrical hot mold was open at both ends and was placed on a large copper chill plate shortly before casting. The solidification of the lead oxides proceeded upwards without any formation of internal cavities. The sample was carefully checked with respect to density and crystalline appearance, and only the lower portions which were crystalline and free from porosity were used. The density was determined in a specially made pyknometer-like container, where the surplus liquid was squeezed out through an orifice approximately 1/10 mm in diameter. Mercury or water was used as the liquid. The densities of the samples were calculated from the weight, volume, and mean specific gravity of eight samples was 9.62 * 0.05 g cm"3 at 22"~. 2) The samples were machined to approximately 1 1/2 in. in length and fitted into a dilatometer. A

Jan 1, 1962

By A. McLean, D. W. Gomersall, R. G. Ward

An experimental study has been made of the solubility of nitrogen in liquid iron and liquid Fe-C alloys using levitation melting and a rapid quenching device. Iron alloy droplets were equilibrated with nitrogen gas at 1 atm pressure, quenched, and analyzed. Previous techniques for studying the Fe-C-N system have produced data which me in marked disagreement. This disagreement is due largely to errors caused by reaction between the molten alloy and the crucible material. With the levitation procedure, errors from this source have been eliminated and precise solubility data obtained for temperatures between 1450° and 1750°C. C-N interactions in molten iron have been expressed in terms of first- and second-order free energy, enthalpy, and entropy parameters. ALTHOUGH the solubility of nitrogen in iron base alloys is in general small, the effects of nitrogen on the properties of steel may be quite profound. For most purposes nitrogen in finished steels is undesirable, particularly in the low-carbon grades, since on cooling to room temperature the solubility limit of nitrogen in the steel may be exceeded and this can lead to embrittlement and loss of ductility on aging. On the other hand, nitrogen can improve the work-hardening properties and machinability of steels while in certain stainless grades nitrogen is important in order to stabilize the austenite phase. It is, therefore, desirable that one should be able to predict the solubility of nitrogen in liquid iron alloys. To do this, information is required concerning the interactions between nitrogen and the various alloying elements which may be present in liquid iron. There have been several investigations of these effects in recent years1"7 and the interactions between nitrogen and many elements dissolved in liquid iron are now known to a high degree of precision at steel-making temperatures. Unfortunately, a number of iron alloy systems which are of interest in steelmaking have been difficult to deal with by the experimental techniques generally used for this type of investigation. Among the most important of these are the Fe-C alloys. In the past, two methods have been widely used for determining nitrogen solubilities: the Sieverts' technique, in which the amount of nitrogen required to saturate a given mass of liquid metal at a particular temperature and pressure is measured volumetrically, and the sampled-bath technique in which liquid metal held in a crucible is equilibrated with a gas phase containing a known partial pressure of nitrogen, and samples drawn from the melt are quenched and analyzed. These two methods have been discussed in detail elsewhere.5,8 With the Sieverts' technique, errors may be introduced from the following sources: i) Gas adsorption on metal films which have condensed on the cooler parts of the reaction chamber. ii) Uncertainty in the determination of "hot volume" calibrations. iii) Crucible-melt interaction, particularly if a gaseous reaction product is formed or if the melt becomes contaminated with material from the crucible walls. The sampled-bath method may also suffer from errors due to reaction between the melt and the crucible material. In addition, there is the possibility that gas may be lost from the sample during solidification and cooling. In the present investigation, the solubility of nitrogen in liquid iron alloys has been studied by means of a new technique based on the use of levitation melting equipment and a rapid quenching device. In addition to the fact that problems of the type outlined above are avoided, this particular approach has the following advantages: i) The high-frequency current induces vigorous stirring within the levitated droplet so that gas-metal equilibration is rapidly attained. ii) The gas phase surrounding the melt can be changed very quickly and is easily controlled. For example, a droplet may be levitated in helium, deoxidized in hydrogen, equilibrated with nitrogen, and quenched, within a period of 15 min. ii) Melts can be readily under cooled or superheated, thus extending the effective temperature range of an investigation and allowing temperature-dependent data to be determined with a high degree of precision. Excellent reviews of levitation melting techniques and their application to physical-chemistry studies at high temperature have been published recently by Jenkins et al.,9 Peifer,10 and Rostron.11 In the present investigation a levitation melting technique has been used to obtain data for the solubility of nitrogen in pure liquid iron and liquid Fe-C alloys at temperatures between 1450° and 1750°C. The solution of nitrogen in liquid iron can be described by the reaction:

Jan 1, 1969

By W. Mckewan, W. M. Fassell

The oxidation rates of copper have been determined at temperatures from 600" to 900°C in oxygen from 14.7 to 400 psi total oxygen pressure. The oxidation rate of copper is unchanged by oxygen pressures within the range studied. The observed data extend Feit-knecht's conclusion concerning the pressure independence of copper from atmospheric pressure to 400 psi. All samples studied in the above-mentioned temperature and pressure range have both Cu2O and CuO present in the oxide film. NUMEROUS papers have been published on the oxidation of copper, some of which have noted the effect of oxygen pressure on the oxidation rate of copper. It must be noted, however, that no data on the oxidation rates of copper at pressure in excess of 1 atm have been reported in the literature. (Le Chatelier¹ reported that a black oxide of silver was formed at 300°C and 15 atm pressure.) This is likewise true for the other metals. This investigation was initiated to obtain experimental oxidation rate constants for pure metals at elevated temperatures and high oxygen pressure. Copper was selected as the first metal since probably more reliable data are available on its oxidation rates and related physical and chemical properties than for any other metal or alloy. As a general summary, the following conclusions appear well established for the oxidation of copper: 1—The oxide coating consists of Cu2O with a superficial coating of CuO providing the ambient oxygen pressure exceeds the equilibrium pressure for the coexistence of Cu2O and CuO.² The following sequence of phases is then Cu/Cu2O/CuO/O2 (gas). The Cu2O consists of large crystals that have no relation to the orientation of the metal crystals, except for a very thin layer adjacent to the metal." The CuO consists of very fine crystals randomly oriented. If the oxygen pressure is below the equilibrium pressure for the coexistence of Cu2O and CuO, the coating consists of Cu,O only. 2—The rate-determining factor in the parabolic oxidation of copper is the diffusion of Cu+ ions through the Cu,O layer.4,6,7 The Cu+ ions are accompanied by electrons to maintain electrical neutrality. The mechanism of the reaction at the Cu2O/CuO interface and the method of growth of the CuO is in some doubt. 3—On copper, there are three reported pressure effects: (a) At pressures below 0.3 mm Hg oxygen pressure, the oxidation rate increases directly with pressure.', ' .Vxygen starvation at the surface may account for this effect. (b) At oxygen pressures from 0.3 to 63 mm, the oxidation rate increases as the 7th root of the oxygen pressure providing the temperature is such that only Cu2O is present in the film. (c) At pressures from above the equilibrium pressure for the coexistence of Cu2O and CuO (varies with temperature) to atmospheric pressure, the oxidation rate is independent of the oxygen pressure.' Equipment In order to determine the oxidation rates of metals in an oxidizing atmosphere at pressures up to 400 psi, the equipment is somewhat different than for low pressure work as is shown in Figs. 1 and 2. A Leeds and Northrup Micromax recording controller (A) is used to control the temperature of the Ni-chrome furnace winding in conjunction with a Micromax electric drive unit. The drive unit adjusts a 20 amp Variac (variable transformer) to control the power input into the Nichrome furnace winding. Due to the "self heating" of the sample by oxidation, frequently encountered in oxidation rate studies, it is essential that the sample temperature be measured independently. This is done by means of a series of six chromel-alumel calibrated thermocouples located spirally around the oxidizing metal sample. Each thermocouple is partially shielded from the direct radiation of the furnace wall by

Jan 1, 1954

By C. E. Birchenall, G. Derge

IN studying the kinetics of slag-metal reactions, it has become increasingly apparent that a complete knowledge of all aspects of interface phenomena will be required to clarify these processes adequately. A part of the data required for all oxidizing slags used in the refining of impure iron to steel is the rate of exchange of iron between the slag and metal phases. The simplest equilibrium of this type is that between liquid iron and iron silicate slag when both phases are equilibrated with the silica crucible containing them. In this study, the exchange of iron between the two liquid phases has been measured by using radioactive Fe as tracer. The observed high exchange rate indicates the ease with which such interfaces may be crossed in refining processes. The experiments required for this study involved relatively minor and normal modifications of well established techniques. Melting was accomplished by induction heating in heavy walled, fused silica, rotating crucibles." Rotation was used to minimize dilution of the slag by crucible erosion. The melting stock was ingot iron. Slags were prefused in iron crucibles using chemically pure grade oxide reagents. The special conditions applying to the active iron additions will be described for individual experiments. Suitable precautions were observed with regard to protection against radiation hazards.' Identification of Activity This particular study was initiated several years ago, but held in abeyance because the radioactive iron available at that time contained a foreign activity which concentrated in the slag so as to mask the iron activity and render the results unin-terpretable. With the benefit of experiences from other studies, radioiron of suitable purity can now be prepared. As received from the Isotope Div. of A.E.C., the unit appears to contain Fe + Fe50 and a high activity cobalt. The cobalt and iron are separated by repeated ether extractions, and the purified iron stored for sufficient time for the Fe'7 44 day half-life) to decay to negligible activity, leaving only Fe as the active isotope. This was confirmed by the absorption curves for slag and metal samples from heat No. 1. In Fig. 1 the experimentally measured points for the absorption curves of slag and metal are fitted by the calculated slope of 5.8 mg per sq cm in aluminum, which corresponds to the Mn K doublet emission resulting from the capture of an orbital electron of Fe" by the nucleus. This shows that the radioactive species are the same in both slag and metal and identifies it as Fe55 Description of Individual Heats For the first heat, the radioactive iron was contained in the prefused slag. The active Fe55 had been precipitated with carrier and was added as Fe2O3 during fusion in the iron crucible. The charge of 500 grams of ingot iron was melted, the protective iron sleeve added, rotation started, and a prefused, inactive slag was added to allow the system to approach equilibrium. After about 5 min at temperature, the wash slag was skimmed and the active slag added. Initial slag and metal samples were taken as soon as the slag was molten. Additional samples were taken at indicated intervals thereafter. Slag samples were dipped with a small iron spoon and metal samples were sucked into 1/4 in. ID silica tubes. The slag and metal samples were pulverized and mounted for radioactive counting. The slag samples were analyzed chemically for FeO. Temperature was read after the last slag sample by immersion of a Pt-Pt-Rh thermocouple protected by a fused silica sheath. Since no significant variation of rate with temperature was observed

Jan 1, 1954