Search Documents

By C. A. Siebert, G. Sandoz

Oil quenching of steel, in good commercial practice, is carried out using a great deal of agitation in the quenching bath. Many of the tests reported in the literature represent the results obtained on steels quenched into still oil. Scott1 describes three stages of cooling in liquid quenching baths, namely: "State 'A'— Vapor Blanket Cooling—In this, the first stage, a thin stable vapor film surrounds the hot metal. Cooling is by conduction and radiation through the gaseous film and is therefore relatively slow. "Stage 'B'—Vapor Transport Cooling— Termination of the 'A' stage is marked by wetting of the metal surface. Vapor forms copiously in bubbles and is carried away by gravity and convection currents to condense in cooler surrounding liquid. This is the fastest stage of cooling. "Stage 'C'—Liquid Cooling—The 'B' stage ends as the surface temperature of the metal approaches the boiling point of the quenching liquid. Vapor no longer forms, so cooling is by conduction and convection and the temperature difference is greatly decreased. This mode of cooling is slower than that of the 'B' stage." Mechanical agitation of the quenching medium will accelerate all three stages of cooling. The greatest effect, however, will be noted on stage ' B' because the removal of the bubbles from the surface of the steel will not be entirely dependent upon gravity and natural convection currents. The method employed in this investigation for evaluating the oils was the end quench test. The various oils were substituted for water as the quenching liquid and hardness determinations were made at various distances from the quenched end. Most of the tests were run using a 3/8-in. orifice with a 21/2-in. stream height. However, to check the effect of other velocities two additional conditions were used, namely: (I) A 3/8-in. orifice and I-in. stream height, and (2) a 1/2-in. orifice and a 31/2-in. stream height. In all cases the samples were suspended so that the quenched end was 1/2-in. above the orifice. Some tests were run on an NE 8740, .3,312, and a 4340 steel. The results obtained on these steels confirmed those obtained on the NE 9450 and have therefore been Omitted from this paper. The test bars were machined from 1/8-in. stock to I-in. diam by 4 in. long.

Jan 1, 1949

By G. Sandoz, C. A. Siebert

Oil quenching of steel, in good commercial practice, is carried out using a great deal of agitation in the quenching bath. Many of the tests reported in the literature represent the results obtained on steels quenched into still oil. Scott1 describes three stages of cooling in liquid quenching baths, namely: "State 'A'— Vapor Blanket Cooling—In this, the first stage, a thin stable vapor film surrounds the hot metal. Cooling is by conduction and radiation through the gaseous film and is therefore relatively slow. "Stage 'B'—Vapor Transport Cooling— Termination of the 'A' stage is marked by wetting of the metal surface. Vapor forms copiously in bubbles and is carried away by gravity and convection currents to condense in cooler surrounding liquid. This is the fastest stage of cooling. "Stage 'C'—Liquid Cooling—The 'B' stage ends as the surface temperature of the metal approaches the boiling point of the quenching liquid. Vapor no longer forms, so cooling is by conduction and convection and the temperature difference is greatly decreased. This mode of cooling is slower than that of the 'B' stage." Mechanical agitation of the quenching medium will accelerate all three stages of cooling. The greatest effect, however, will be noted on stage ' B' because the removal of the bubbles from the surface of the steel will not be entirely dependent upon gravity and natural convection currents. The method employed in this investigation for evaluating the oils was the end quench test. The various oils were substituted for water as the quenching liquid and hardness determinations were made at various distances from the quenched end. Most of the tests were run using a 3/8-in. orifice with a 21/2-in. stream height. However, to check the effect of other velocities two additional conditions were used, namely: (I) A 3/8-in. orifice and I-in. stream height, and (2) a 1/2-in. orifice and a 31/2-in. stream height. In all cases the samples were suspended so that the quenched end was 1/2-in. above the orifice. Some tests were run on an NE 8740, .3,312, and a 4340 steel. The results obtained on these steels confirmed those obtained on the NE 9450 and have therefore been Omitted from this paper. The test bars were machined from 1/8-in. stock to I-in. diam by 4 in. long.

Jan 1, 1949

By O. G. Bell

While all of the Southwest Texas fields lie within the Gulf Coastal Plain this area may be divided into three subdivisions—the Coastal Plain zone proper, the Reynosa Escarpment zone, and the interior zone. The Coastal zone includes that strip adjacent to the Gulf of Mexico and . extending inland for a distance of about 60 miles and includes the Palo Blanco, Palangana, Piedras Pintas, Kingsville, Agua Dulce, Saxet, White Point and Refugio fields. The Reynosa Escarpment zone includes a Pliocene overlap over older Tertiary sediments lying west of the Coastal zone. The western margin of the Reynosa formation forms a more or less well-defined westward facing escarpment with which the so-called Reynosa Escarpment fields are indirectly related. These fields include those in eastern Zapata, eastern Webb, western Jim Hogg, western Duval, McMullen, Live Oak, Bee, Goliad and Victoria counties. The interior zone includes these fields west of the Reynosa Escarpment which are not in any way related to it and are on separate types of structure. Production data by fields and wells are shown in Table 1. Roma.—During 1928 the Texas Co. completed two small gas wells at 198 ft. on the Roma Structure near the town of Roma on the Rio Grande in Starr County. This gas is of no commercial importance but was used for fuel in drilling other deep tests on this structure. Three dry holes ranging from 3600 to 4200 ft. were drilled; then their No. 4 Guerra, the fourth deep test, was completed during December as a small producer of 37" Bé. oil from a sand at 3560 to 3590 ft. No production was marketed during December but arrangements were being made to handle the output from this well during 1930. This is the first commercial producer in Starr County. Driscoll.—In 1929, Robert Driscoll discovered gas on his Santa Rosalia Ranch in Duval County while drilling water wells. Two sands were developed, one at 2400 ft. and another at 2936 ft. and several gas wells were completed in each, ranging in volume from 15,000,000 to 40,000,000 cu. ft. and in reservoir pressure from 500 to 1,000 Ib. Early in January of 1929, Mr. Driscoll's No. 14 Fee was completed as a 50-bbl. oil producer at 2894 ft. Two other oil producers were completed early in 1929. Mr. Driscoll's death early in the year curtailed develop-

Jan 1, 1930

By G. Sandoz, C. A. Siebert

OIL quenching of steel, in good commercial practice, is carried out using a great deal of agitation in the quenching bath. Many of the tests reported in the literature represent the results obtained on steels quenched into still oil. Scott1 describes three stages of cooling in liquid quenching baths, namely: "State `A'-Vapor Blanket Cooling-In this, the first stage, a thin stable vapor film surrounds the hot metal. Cooling is by conduction and radiation through the gaseous film and is therefore relatively slow. "Stage `B'-Vapor Transport Cooling- Termination of the `A' stage is marked by wetting of the metal surface. Vapor forms copiously in bubbles and is carried away by gravity and convection currents to condense in cooler surrounding liquid. This is the fastest stage of cooling. "Stage `C'-Liquid Cooling--The `B' stage ends as the surface temperature of the metal approaches the boiling point of the quenching liquid. Vapor no longer forms, so cooling is by conduction and convection and the temperature difference is greatly decreased. This mode of cooling is slower than that of the `B' stage." Mechanical agitation of the quenching medium will accelerate all three stages of cooling. The greatest effect, however, will be noted on stage `B' because the removal of the bubbles from the surface of the steel will not be entirely dependent upon gravity and natural convection currents. The method employed in this investigation for evaluating the oils was the end quench test. The various oils were substituted for water as the quenching liquid and hardness determinations were made at various distances from the quenched end. Most of the tests were run using a 3/8-in. orifice with a 2 ½ -in. stream height. However, to check the effect of other velocities two additional conditions were used, namely: (I) A 3/8-in. orifice and 1-in. stream height, and (2) a ½ -in. orifice and a 3 ½ -in. stream height. In all cases the samples were suspended so that the quenched end was ½ -in. above the orifice. The steel used was an NE 9450 having the following analysis: [ ] Some tests were run on an NE 8740, 3312, and a 4340 steel. The results obtained on these steels confirmed those obtained on the NE 9450 and have therefore been omitted' from this paper. The test bars were machined from 1 1/8 -in. stock to 1-in. diam by 4 in. long.

Jan 1, 1948

By J. P. Denny

The constitution of the Ga-In system was determined by thermal methods. An experimentally determined metastable equilibrium line (an extension of the indium-rich liquidus) was obtained. The various alloys were studied metallographically using polished samples obtained by a casting method. These low melting alloys required a special dry-ice assembly to maintain a suitable temperature. RECENT interest in alloys that are liquid at room temperature has led to rather extensive investigation of gallium-base alloys. Widely distributed over the earth, gallium could be produced in substantially larger quantities than at present, if a significant demand existed.' One study' has established its presence in 12 out of 14 zinc blends, in all of 15 aluminum ores, in 4 out of 12 manganese ores, in 35 out of 91 iron ores, and in all of 7 magnetite ores. It occurs as a rule in minute amounts, however, leading to high extraction costs. Recent quotations run from $2.50 to $7.50 per g. During the course of the present investigation, portions of the system Ga-In have been redeter-mined, and the results of this study are presented herein. Thermal and metallographic methods have been employed. Lecoq de Boisbaudran, the discoverer of gallium, conducted the first investigation" on Ga-In alloys in 1885. The temperatures of incipient melting, and of completion of melting, were determined at four alloy compositions. In 1936, Hansen' constructed a eutec-tic-type phase diagram for the system Ga-In, based on . work. The existence of a Ga-In compound was regarded as improbable by Hansen, and subsequent investigations are in agreement. French, Saunders, and Ingle3 conducted a more complete study of the system in 1938, using thermal methods. Their phase diagram is a eutectic type, containing a unique concave-upward liquidus. The solid-solution range of gallium in indium was reported as 9.5 pct by weight, and that of indium as less than 1 pct, at the eutectic temperature. The eutectic composition, determined as being bracketed by the compositions showing a true horizontal at the eutectic temperature (16°C), was reported as 76 5-0.5 pct Ga and 24 i 0.5 pct In. Experimental Procedure The preparation of Ga-In alloys is simplified by the low melting points involved. Various compositions were prepared by melting in pyrex tubes, using a cover of distilled water or parafin to prevent the alloys from wetting the glass wall. In all cases, the melts were homogenized. by stirring. Where possible, both cooling and melting curves were determined. The extensive undercooling of gallium was found to prohibit a satisfactory cooling-curve analysis of gallium-rich alloys, however, and transition points on the gallium side of the eutectic could be determined only by melting curves. The inverse rate method of thermal analysis proved to be most satisfactory and was used to a great extent. Various heating and cooling rates were used, ranging from 0.2" to 5.0°C per min. Low temperature melting analyses were conducted within a constant temperature bath, maintained at about 70 °C. The alloys were solidified (under water or paraffin) within a pyrex tube, using dry ice; the tube was then sealed within a cold Dewar flask, the unit transferred into the constant temperature bath, and periodic temperature readings taken. The high temperature melting-curve determinations and all cooling-curve determinations were made in a vertical tube furnace. At near-eutectic compositions, the furnace was placed within a refrigerated room held at —20°C. Accordingly, the furnace on cooling approached —20°C asymptotically and permitted the determination of those phase transitions occurring below room temperatures. Temperatures were measured with a 30-gage iron-constantan thermocouple, immersed directly in the alloy. To prevent contamination of the melt, the leads and junction were coated with Lucite, applied by painting with a solution of Lucite in ethylene dichloride. Electromotive force measurements were made with a Leeds and Northrup precision potentiometer, type 8662. The couples were calibrated against the boiling point. of water and, at lower temperatures, against a calorimeter thermometer having a Bureau of Standards certificate. The melting points of gallium and indium used in the present investigation were determined as 29.-77° and 156.1°C, in good agreement with previously reported values of 29.78°C° and 156.4"C.' The spec-

Jan 1, 1953

By Nathaniel Arbiter, Arthur F. Taggart

THE chemical reaction occurring in collection of nonmetallic minerals with amine-type collectors was early postulated by students of flotation phenomena to be metathesis between the mineral and the collector, involving exchange between the amine-bearing (aminium) ion and the cation of the mineral, and formation at the mineral surface of an oriented film of the amine salt of the mineral anion. Qualitative evidence of exchange has been obtained on several occasions at Columbia. Thus 1000 c.c. of a solution containing 495 mg. of laurylamine hydrochloride was shaken 17 min. with 100 grams of barite and ground in a porcelain mill to pass a 200-mesh screen; the mixture was then set aside for 48 hr. Filtrate therefrom analyzed 476 mg. per liter of laurylamine hydrochloride. There was no substantial loss of chloride ion (78.4 mg. per liter in the original; 74 in the filtrate). No successful analyses were concluded for barium ion. Earlier, confessedly rough work with scheelite indicated a solution gain in Ca++ equivalent to about one-half the aminium ion lost. Real quantitative proof of the exchange, in the form of an established stoichiometric balance, is unknown to the authors. The data of the present paper, however, obtained from experiments designed on the basis of the exchange hypothesis, constitute strong evidence of its truth, and at the same time point the way to economic utilization of the expensive nitrogen-bearing collectors in concentration of the low-priced nonmetallic minerals. The basic postulate underlying the experiments performed was that, if the collecting reaction is of the type [R+ + Y- + MX =± RX + M+ + Y¬] where R = aminium ion, Y = the anion of the amine salt, and M and X are, respectively, the cation and anion of the mineral, the reaction should obey qualitatively the implications of the massaction and solubility-product laws. This is to say that coating and collection should be aided by the addition to the solution of either ion (R+ or X-) of the collector-coating compound, and hindered by the addition of either of the ions M+ or Y-. Experimental work comprised determination of (1) the relative solubilities of the laurylammonium salts of a variety of nonmetallic-mineral anions; and (2) the contact angles1 of various minerals in solutions containing different concentrations of the postulated controlling ions. Semiquantitative flotation tests were run with barite as checks on the diagnostic character of the contact angles. The amine

Jan 1, 1944

COMMITTEES. Iron and Steel. Albert Sauveur, Chairman. A. A. Stevenson, Vice-Chairman. Herbert M. Boylston, Secretary, Abbot Bldg., Harvard Sq., Cambridge, Mass. LOCAL COMMITTEES. Program Committee.-A. A. Stevenson, Chairman. Herbert A3. Boylston, J. E. Johnson, Jr., Henry D. Hibbard, E. Gybbon Spilsbury. Reception Committee.-J. R. Johnson, Jr., Chairman. Felix A. Vogel, William R. Walker. Dinner Committee.-E. Gybbon Spilsbury, Chairman. The opening session was held on Thursday morning, Oct. 16, 1913, at the Institute Headquarters in the Engineering Societies Building, 29 West 39th Street, New York, N. Y., and was called to order by President Rand, who addressed the meeting briefly before presenting Albert Sauveur, who responded to the President's address, and presided at the meeting. The following papers were then presented in oral abstract by their authors or authors' representatives: The Cleaning of Blast-Furnace Gas, by W. A. Forbes. Discussed by S. K. Varnes, H. N. Diehl, F. H. Wagner, Joseph Hartshorne, S. B. Marshall, J. W. Richards, J. E. Johnson, Jr., W. A. Forbes, and others.

Jan 12, 1913

By H. I. Aaronson, H. A. Domian, A. D. Brailsford

A current study of the growth kinetics of k (hcp) plates in a Cu-Si (fcc)' has generated a requirement for data 02 the chemical interdiffusion coefficient in a (termed D,) as a function of temperature at the composition of the a/a + k pJase boundary. Rhines and Mehl 2 have determined D, as a function of composition at lower silicon contents by making Matano analyses of concentration-penetration curves. However, the accelerating increase in B, which they demonstrated as the phase boundary composition is approached at constant temperature and the rapidly diminishing accuracy of this analysis as the limiting compositions of a diffusion couple are approached (the silicon-rich component of their couples contained appreciably less silicon than is permitted by the solubility limit) indicate that the required information cannot be safely obtained by extrapolation of their data. Although the quite different method employed in this study is not exact, it will be shown that the approximations made are not serious ones, particularly from the viewpoint of the prgcipal application anticipated for these data. D, was determined from the migration kinetics of the a :k boundaries formed in sandwich-type diffusion couples produced by welding a block of high-purity copper to opposite sides of a cube (* in. on edge) of homogenized high-purity Cu-5.82 wt pct Si alloy. The alloy is pure k in the temperature range employed. The surfaces of the couple components which were normal to the diffusion direction were machined accurately flat and parallel, lightly polished, and carefully cleaned. Welding was then accomplished by means of the vacuum-encapsulated pressure jig technique previously employed.3 Welding was always conducted at the intended diffusion temperature; thus the welding anneal also served as the first diffusion anneal. Subsequent diffusion anneals were performed in evacuated Vycor capsules. Following the welding anneal, one of the surfaces parallel to the diffusion direction was machined, ground, and polished flat; additional material was removed from this surface after each diffusion anneal in order to avoid any effects of composition changes. After etching,4 the average distance between a : k boundaries was measured by means of a traveling microscope with an accuracy (per measurement) of better than 1 p. Satisfactory results were obtained at four temperatures in the range 775° to 655°C; attempts to obtain data at two lower temperatures were unsuccessful, evidently as the result of the interference of surface contamination during the welding process.

Jan 1, 1969

By Ralph H. Sweetser

AT the end of 1943 the charcoal pig iron capacity of the United States was at the lowest point in over 1110 years, with only one strictly charcoal blast furnace in operation, and all others permanently out of blast except one in Tennessee d reported to he running on part charcoal and part coke. Such a decrease in production has taken place in spite of the O.P A.'s high-premium price on charcoal pig iron of +34 per ton f.o.b. furnace in Michigan. Depletion of the hardwood supply within fifty mlles or inure of the blast furnace is the reason why; the deplorable lack of reforesting is the cause.

Jan 1, 1944

Papers published by the Institute are issued in a variety of forms MINING TECHNOLOGY, issued every other month, contains the TECHNICAL PUBLICATIONS on Metal Mining, Minerals Beneficiation (milling and concentration), Industrial Minerals (nonmetallic) and Mining Geology, Mining Administration, and Geophysics papers relating to Metal Mining (A, B, H, I, K, L ) METALS TECHNOLOGY, issued eight times a year, contains the TECHNICAL PUBLICATIONS of the Iron and Steel Division and the Institute of Metals Division, and once or twice during the year those on Non-ferrous Metallurgy (reduction and refining of nonferrous metals) (C, E, and D ) PETROLEUM TECHNOLOGY, issued every other month, contains the TECHNICAL PUBLICATIONS of the Petroleum Division, together with Geophysics papers relating to -the finding of Petroleum (G, L ) COAL TECHNOLOGY, issued four times a year, contains the TECHNICAL PUBLICATIONS of the Coal Division (F ) MINERAL INDUSTRY EDUCATION DIVISION papers appear in a TECHNOLOGY according to classification of subject matter DISCUSSIONS appear in the respective TECHNOLOGY as available MINING AND METALLURGY is the monthly magazine, which contains papers of general interest and news of the membership

Jan 1, 1952

By A. H. Daane, W. J. Wunderlin, B. J. Beaudry

In an earlier study at this laboratory,' the authors investigated the solid solubility of holmium in copper, silver, and gold, and also the melting point of the first eutectic on the noble-metal-rich side in these systems. In a more recent study of the solubility of rare-earth metals in gold at this laboratory. Rider, Gschneidner, and McMasters2 noted that the reported eutectic temperature in the Ho-Au system was lower than the corresponding eutectics in systems of dysprosium and erbium with gold. A redetermination of the eutectic temperature in the Ho-Au system with the same alloy used in the original study showed the eutectic temperature to be 810°C instead of 778°C as originally reported. (The eutectic temperatures in the Ho-Ag and Ho-Cu systems were also redetermined and were found to be 795" and 864°C compared to 787° and 868°C, respectively, which were reported originally.) Since this large change in eutectic temperature made the solubility data appear questionable, new alloys were prepared, heat-treated, and examined metallographically. The procedure of sample preparation and heat treatment used in the original work' was followed except longer heat treatments were used ranging from 7 days at 600°C to 6 hr at 900°C. The results obtained are shown in Fig. 1. There is good agreement between the two studies in the maximum solubility of holmium in gold. Since the slope of the solvus is less pronounced in the present study, the extrapolation to 550°C shows a solubility of 1.6 wt pct Ho in gold compared with 1.0 wt pct in the original work. Since additional data were obtained and longer heat treatments were used in the present study, the larger value is believed to be more accurate. The authors wish to express their appreciation to P. Rider and K. A. Gschneidner. Jr., for bringing this discrepancy to their attention, and also to D. Thompson for assisting in the present study.

Jan 1, 1965

By O. C. Wheeler

The principal interest in the oil situation in Colombia during the year centered around the enactment of the new petroleum law and the applications for concessions subsequently made by various interests. The year was a comparatively uneventful one from the standpoint of actual operations of drilling and development. There was a falling off both in exploratory work and in the development of producing properties; and as a result of curtailment of production, the output of oil from the country dropped to the lowest level since the completion of the looping of the Andian pipe line to the coast in 1927. Legislation Law No. 371 of 1931, with its Regulatory Decree No. 1270, was enacted during the year and marked Colombia's attempt to encourage more extensive exploration and development of the prospective oil resources of the country. Some of the outstanding provisions of the law are as follows: Tracts may be acquired by a concessionnaire directly and by transfer ranging from 5,000 to 100,000 hectares, except in certain reserved territories east of the summit of the eastern cordilleras where the maximum is increased to 200,000 ha. A security deposit of $1 per hectare, minimum $25,000, is required on government grants, and is returned to the concessionnaire only upon the fulfillment of stipulated terms of the law. Rentals, increasing progressively from 10c per hectare per year the first two years to 50c per hectare the sixth year, are required up to the start of the production period (beginning of development). The concession terminates 30 years after the beginning of the production period and can be extended for 10 years more at the option of the contractor. Wells must be produced at no less than 25 per cent of their maximum capacity. Royalties on oil from national lands vary from 2 to 11 per cent of the gross product, depending on the distance of the concession from the port of loading. Petroleum from private property is subject to a governmental tax varying from 1 to

Jan 1, 1932

Prof. G. W. MAYNARD, New York City (communication to the Secretary): Prof. Christy, in his admirable paper on "The Growth of American Mining Schools," has overlooked the work done by the Rensselaer Polytechnic Institute in its department of mining and metallurgy. This oversight is naturally due to the fact that the department was, for lack of money, discontinued in 1871. It was organized by the writer in 1867, starting with ten students, who had already completed the first two years of the civil engineering course in the Institute. The course covered two years, specifically devoted to mining, metallurgy and assaying, which, in connection with the two years' drill in the civil engineering department made a four years' course. During the four years of the existence of the department, thirty-five students took the course, of whom twentyfive graduated; and of this number eight have been members of the Institute of Mining Engineers, and the majority of them have occupied high positions in the profession. The equipment of the department was, at that time, second only to that of the Columbia School of Mines. As Prof. Christy has cited other institutions which are not distinctively mining schools, but in which the ruining course was subordinate to other courses, it seems to me that the work in this line carried out by the oldest engineering school in the country may very properly be referred to. In addition to the regular mining course, a special course in assaying was given; and many young men were here prepared for positions in the mines and metallurgical works of the west. PROF. George F. Swain, Boston, Mass.: I have listened with great interest to Prof. Christy's valuable paper, but there is one conclusion at which he arrives that appears to me entirely unjustifiable, and to which I desire to take exception. Prof. Christy finds that of the total wage-earners in the United States in 1880,10.41 per cent. were employed in " trade and transport;" 20.24 per cent. in " manufactures and mechanics," and 1.83

Jan 1, 1894

By William C. Peters

The pre-production interval, beginning with the recognition of an orebody's best potential and ending with significant production, contains time-dependent conditions well appreciated by miners but not always understood or appreciated by the landowners, investors, and legislators with whom a miner must deal. The expression persists, even outside of Western fiction, that someone has "found a mine." From a slightly more knowledgeable position, the question is asked "How long does it take to make a mine?" and an all-encompassing answer is expected. By scanning the discovery and development history of hundreds of mines and rejecting those which involve rehabilitation or expansion of older mines, some generalizations can be attempted. It should be kept in mind that while physical conditions involving the geology of the orebody and the geographic surroundings do not change markedly with time, technologic and economic conditions do change from year to year. The new methods, facilities, markets, land tenure, and politics form a pattern in which today's mines are made and which do sometimes modify the pre-production interval.

Jan 8, 1966

Colorado School of Mines Scientific Society held its first meeting on Friday evening, Jan. 14.1916. H. C. Parmalee gave an interesting talk on the Loss of Cyanide by Hydrolysis. F. E. BRIBER, Secretary. The School of Mines Society of the University of Minnesota held a meeting on Thursday evening, Jan. 13, 1916, at which Fred A. Jordan gave a talk on Magnetic Concentration of Iron Ores. Mr. Jordan is at present testing the new magnetic concentrator designed at the. School of Mines Experiment Station. This apparatus, if successful, will open up an enormous tonnage of ore on the Cuyuna and Mesabi ranges. ADOLPH DOVRE, President. At the College of Mines, University of Washington, Seattle, 33 mining men, with experience varying from one to 25 years, have enrolled in the 19th Annual Three Months' Short Session. At the annual smoker tendered the Short Session miners by the student branch of the American Institute of Mining Engineers, Capt. R. H. Stretch of the Alaska Bureau, Seattle Chamber of Commerce, delivered an address on The Mineral Belts of Alaska.

Jan 3, 1916

By Rudolph G. Wuerker

Charles T. Holland (Head, Dept. of Mining Engineeri*, Virginia Polytechnical Inst., Blacksburg, Va.) Mr. Wuerker has presented a very interesting discussion of the use of triaxial test methods for investigating the strength properties of rocks. Such methods, no doubt, eventually will develop considerable information of interest to those concerned with the design of mine layouts, particularly in the field of pillar design. From his discussion of my recent article, "Cause and Occurrence of Coal Mine Bumps" (Holland Mining Engineering 1958, p. 933-1002), it is evident that in one place at least I did not make my meaning clear to him and perhaps others. To clear the matter up I think it best to quote from the article, somewhat more fully than did Mr. Wuerker, as follows: "4) In actual operations — because rocksare not perfectly elastic, homogeneous, nor isotropic and because local yield does occur — the maximum stress as demonstrated by Phillips (Ref. 22, pp. 64, 65) and indicated by much experience in mining, does not occur at the walls of the opening but at a short distance inside the pillar. Furthermore, the maximum stress does not reach as great a value as theoretical considerations and laboratory experimental methods indicate.* Actual distance inside the pillar, measured from the wall, at which the maximum stress exists, has not been determined. Observations in many mines, however, indicate that this distance could have a mini-value of one to six or eight times the bed thickness and that it is probably affected by width and height of the opening, depth of cover, and relative values of the elasticity and plasticity of materials comprising the roof, floor, and coal seam. The actual value of the stress produced probably lies between the theoretical maximum and the average stress concentration that would be produced if the weight of the strata above the unsupported opening were evenly distributed over the pillars for a distance equal to the opening width." The footnote reference in the above quotation referred to the following: "*For example, the Pocahontas No. 4 coal bed in southern West Virginia is mined under cover up to 1800 ft thick. Development openings are driven 18 to 20 ft wide, and the bed is about 6 ft thick. According to the work of Panek, the tangential wall stress at mid-bed height under these conditions would reach values between 4000 and 5000 psi. Actual tests of 3-in. cubes of this coal show its compressive strength would be much less than this, perhaps as low as 400 psi. Yet the pillars usually show no evidence of failure in these headings. In this same bed at a depth of 800 ft, the author has seen an opening 225 ft between supports lying between two old groves approximately 1100 ft apart. According to the theoretical considerations, the stress in the pillar walls would have been about 18,000 psi, yet the pillar showed little or no evidence of weight. In view of these observations, it is clear that the wall stress does not attain the maximum values indicated by theory." (Underlining added to original wording.) By referring to Fig. 2A of my paper it will be noted that theoretically the maximum pillar stress would occur at the pillar wall, i.e., at the passageway surface of the pillar. Obviously this cannot be correct in the cases of stress ranging from 4000 to 18000 psi since the coal at the surface of the pillar is under no constraint and cannot have a strength much greater than 400 or 500 psi. Hence, my conclusion that the maximum stress does not occur at the wall but back in the pillar some distance from the wall. Since these stresses are pushed back in the pillar from the wall, it is also obvious that the loads transferred to the pillar from the opening will be spread over a greater area and hence Pillar stresses will not rise to the values postulated by theory and photoelastic experiment. Further since to visual inspection the coal along the pillar wall did not appear to be failed the conclusion was reached that the stress shift was caused by local elastic or plastic yield and by difference in the elastic modulus of the rocks composing the mine floor, mine roof, and coal bed. Later on under the heading "Strength of Mine Pillars" (pages 1000-1002) the effects of constraint is briefly described. Also a formula taking into account constraint is developed relating pillar strength to the uniaxial strength of coal and the L/T ratio of the pillar. Since my paper was written, reports of experiments conducted in South Africa (Denkhaus, et. al., 1959), in Sweden (Hast 19581, and in Canada (McInnes, et.al., 1959) reveal that the conclusion expressed relative to the existence of a low stress area existing around the edges of pillars and solid faces as described above is generally correct. But it seems possible that where the wall stress developed is less than the unconfined strength of the rock composing the pillar and where the roof, floor, and pillar

Jan 1, 1961

A development which could prove significant was the announcement on September 18 by Lone Star Industries, Inc., Greenwich, Conn., that the Snyder process which utilizes shock phenomena to break down ore in seconds, is operational. J. R. Kringel, chairman and president of Lone Star, says this about the process: "This new approach to the comminution of ores not only provides better mineral liberation at lower capital and operating costs, but it also makes a significant contribution toward the more efficient utilization of the country's rapidly depleting mineral reserves." The Snyder process consists of loading the material into a chamber, introducing a compressible working fluid such as steam under 300-500 psi, or as low as 80 psi, and then opening a millisecond-action discharge valve, causing the material to become entrained in the expanding fluid. The mixed fluid moves through a duct toward a discharge zone at near-sonic velocity, and is subject to a variety of extreme shock phenomena which accomplish the desired size reduction and mineral liberation.

Jan 11, 1972

By A. H. Underwood, M. –Ls. Trépanier

INTRODUCTION The King and Beaver mines of Asbestos Corporation Limited (ACL) were joined in 1957 to form the King-Beaver mine. In 1964, ACL purchased the Johnson's Asbestos Company. The combined underground workings are a part of the King- Beaver mine. Asbestos ore is mined at the rate of 4080 metric tons per day (mtpd) to provide 15% of the company's daily requirement in the Thetford Mines area. Figure 1 shows the location of Thetford Mines. Two shafts service the underground. No. 3 shaft, 457 m deep, is used for personnel and material transportation, downcast ventilation, and ore hoisting. No. 4 shaft, 820 m to the south, is 389 m deep. It is used for material transportation and upcast ventilation. Figure 2 shows the relative locations of the shafts and the underground workings. The ore is mined by block caving. HISTORY The orebody outcropped at surface and was first mined as an open pit. Underground mining commenced when open pit mining became impractical. Shrinkage stoping, used initially, was unsatisfactory in the highly fractured ore. Sublevel stoping improved ore recovery and safety, but did not overcome the adverse effects of the un- stable rock. Observations of the rock failures indicated that block caving would be satisfactory. This was confirmed by careful investigation and testing. A method of block caving similar to that used at the Miami Copper Company was adopted. The first block commenced production in June 1933. BLOCK CAVING General A large block of ore is undercut above pre- pared drawpoints. The ore above the undercut caves by its own weight. Caving progresses up- ward as the caved ore is drawn. A large proportion of the rock breaks up in the caving action so that it will pass through the drawpoints. Oversize blocks are broken by drilling and blasting or mudcapping. Figure 3 shows the progressive stages of block caving. In the central part of the ore zone, the vertical dimension of a block is determined by the 132 metres between production levels. When isolated ore pockets are developed, the vertical dimensions of a block depend on the extension of the ore zone above the undercut. The minimum horizontal dimension of an under- cut determines the cavability of the overlying block. When necessary, caving is assisted by drilling long horizontal holes into the block above the undercut and blasting them. This procedure speeds up or restarts caving. It will not ensure complete caving of blocks having undercuts less than 30 m wide. Orebodies suitable for block caving are highly fractured and wide enough to cave freely without excessive dilution. Undercutting must

Jan 1, 1981

By Henry N. McCarl

Lightweight aggregates include a variety of mineral and rock materials used to provide bulk in concrete building units (block), light- weight structural concrete, and precast concrete units, as plaster aggregate, insulating fill, and other structural and/or insulation purposes. They are distinguished from other mineral aggregate materials by their lighter unit weight- 80 to 100 pounds per cubic foot (pcf) or less for loosely packed lightweight aggregates as compared to 125 pcf or more for crushed stone, sand, gravel, air-cooled slag, and other more common mineral aggregates. The various lightweight aggregate materials may be classified into four groups as follows: 1) Natural Lightweight Aggregate Materials-prepared by crushing and sizing natural rock materials such as pumice, scoria, tuff, breccia, and volcanic cinders. 2) Manufactured Structural Lightweight Aggregates-prepared by pyroprocessing clay, shale, or slate in rotary kilns or on traveling grate sintering machines. 3) Byproduct Lightweight Aggregates-prepared by crushing and sizing foamed and granulated slag, cinders, and coke breeze. With the exception of processed slag, this group is becoming less important as time passes. 4) Manufactured Insulating Ultralight- weight Aggregates-prepared by pyroprocessing ground vermiculite or perlite. This chapter will focus on the use of natural lightweight aggregates and manufactured insulating ultralightweight aggregates, and both the production and use of manufactured structural lightweight aggregates with some comments on byproduct materials. Detailed discussion of the production and use of both expanded and air-cooled slag is presented in a separate chapter in the utilization section of this volume, and there are separate commodity chapters on vermiculite, perlite, pumice, and volcanic cinders. Discussion of the commodities covered elsewhere in the book will be limited to observations on their utilization and relation to other lightweight aggregate materials. All materials considered as lightweight aggregates are derived from some initial natural raw material. While historical definitions have included such organic materials as straw and peat as lightweight aggregates, the discussion in this chapter will restrict itself to lightweight aggregates derived from mineral or rock materials. Thus while the actual lightweight material in use may be a manufactured product, it is derived from an ore or raw material that is obviously a mineral resource. In this context, then, the reserves of raw materials for lightweight aggregate use may include iron ore and flux stone (the components of blast furnace slag) as well as coal (the raw material from which cinders are derived) as well as those clay, shale, and slate deposits that display the characteristics of bloating or controlled expansion when subjected to elevated temperatures (1600 to 2400°F.).

Jan 1, 1975

By D. L. Martin, E. R. Parker

IN a previous paper, one of the authors observed that the rate of cooling from the anneal prior to testing greatly influenced the life of copper under sustained load at 200°C. Furnace-cooled bars of oxygen-free copper (with, and without silver) had a life four to twenty-five times that of the water-quenched specimens. The addition of 0.054 per cent silver to the oxygen-free copper increased the life at a stress of 20,000 lb. per sq. in. from about 2 hr. to 50 hr. Fractures in these bars were intercrystalline. An explanation was advanced to account for the profound influence of cooling rate on the rupture properties at 200°C. The suggestion offered was that at the high annealing temperature the minor constituents are distributed at random. By water quenching, this condition is maintained at room temperature, whereas furnace cooling permits some segregation at the grain boundaries. The higher concentration of the minor constituents in the grain boundaries results in a strengthening, so that a longer life at a given stress and temperature results. Small amounts of cadmium or manganese have also been found to increase the life of copper at 200°C., and to a much greater extent than silver .2 The increase in the long-time strength of copper resulting from small additions of cadmium or silver appears to be related, indirectly at least, to the higher softening temperatures of such alloys. The elements, such as silver or cadmium, which greatly increase the rupture life of copper also cause large increases in the softening temperature. As little as 0.05 per cent of cadmium or silver is sufficient to raise the softening temperature more than 100°.3,4 The effects of cooling rate and of minor constituents on the rupture properties are of considerable fundamental as well as practical interest; therefore a more detailed study of their nature was conducted and is reported in this paper. EXPERIMENTAL PROCEDURE Materials The materials studied in this investigation may conveniently be classified in two groups: one consisting of a wide variety of commercial coppers, and the other composed of special high-purity, laboratory-prepared coppers. The commercial materials were tested to determine whether or not the effect of cooling rate occurred with all coppers, whereas the high-purity coppers were investigated in order to establish a basis for evaluating the effect of minor constituents on the rupture properties. In Table I are given the analyses of the coppers tested. The samples I to 6 are commercial materials and were obtained for the most part from stock supplies.*

Jan 1, 1943